Professional Documents
Culture Documents
Electrical Safety Ch-1
Electrical Safety Ch-1
Adapt this list of reminders to your working environment. Be sure to consider company policies
before establishing a written electrical safety program.
Protect flexible cords and cables from physical damage. Check cords for cut, broken, or
cracked insulation.
Keep slack in flexible cords to prevent tension on electrical terminals.
Make sure the insulating qualities of a splice are equal to or greater than the original cord.
Extension cords are for temporary use. Install permanent wiring when use is no longer
temporary.
Verify that all three-wire tools and equipment are grounded.
Water, electrical equipment, and power cords do not mix!
Ground exposed parts of fixed equipment that could be energized.
Use non-conductive tools whenever possible.
Always double-check the operation of your voltage testers by testing a live circuit.
Other Considerations
Determine the reason that a fuse operated or circuit breaker tripped before replacing or
resetting.
Know where your over current devices are (i.e. circuit breakers and fuses) so they can be
easily and quickly reached in case of emergency.
When replacing lamps and bulbs, verify that the replacement matches fixture
requirements.
When planning and performing work on electrical systems and equipment, keep these principles
in mind:
Accident victims can also incur the following injuries from electrical shock:
Every electrical safety program should include a procedure for analyzing the risks and hazards
associated with each job. Employees should always consider the following:
Environment
o Wet or dry
o Indoors or outdoors
o Open or cramped
o Well lit or dim
o Metal ladders in area where overhead wires or exposed conductors are present
o Electrical cords over a heat source
o Overloaded electrical outlets
Condition of Equipment
o Age of equipment
o Integrity of grounding system
o Internal safety mechanisms
o Operating voltage
o Electrical wiring and loads incurred
o Fault current available to produce arc flash
Electrical
Safety Work Practices
o Ensure that operating procedures are up to date and appropriate for conditions
o Evaluate circuit information drawings
o Determine degree and extent of hazards
o Comply with minimum clearances when working around electrical power lines or
other exposed conductors
o Determine approach boundaries:
o Flash protection boundary - linear distance to prevent injury from a potential
arc-flash
o Limited approach boundary - restricted distance for "unqualified" persons
o Restricted approach boundary - restricted distance for "qualified" persons
o Prohibited approach boundary - for direct contact with live parts - flashover
distance
o Determine "flash protection boundary"
o Determine appropriate personal protective equipment based on potential
hazards present
o Always wear safety glasses and a hard hat when working on live circuits
o Use electrically insulated tools
o Use electrically insulated gloves
o Test dates for integrity of equipment and protective clothing - independent
safety lab
o Wear required personal protective clothing (i.e., long sleeve shirt and long
pants)- flame resistant materials for clothing (different weights for protection
dependent on fault levels and clearing times)
o Your hands are your most valuable tools. Protect them by wearing appropriate
safety gloves. Before using, inspect the gloves for signs of wear and tear and
other damage.
o Evaluate personnel qualifications
o Use ladders with nonconductive side rails if there is any possibility the ladder
could contact exposed energized parts
o Follow lock-out/tag-out procedures
o Use power tools that are double-insulated or that have ground-fault circuit
interrupters protecting the circuit
o Inspect all extension cords for wear and tear and make sure they are listed by a
third-party testing laboratory
o Never drape electrical cords over heat sources
o Never store flammable liquids near electrical equipment, even temporarily
o Be aware of special training requirements
o Motors with thermal protection can restart without warning, always lockout the
motor before working on it.
o Only qualified personnel should perform maintenance, inspection and repairs on
any electrical equipment.
o Do not use tin stranded wire with solder - this promotes corrosion and limits
contact area.
o If measuring voltage with respect to ground, make the ground connection first
and remove it last.
o Plugs and connectors should be wired with additional slack. In the event of
undue strain on the cord, the grounding will be the last broken.
o Grounding continuity should be checked on new tools and equipment before
being put into service.
o Remove paint from mating surfaces or use a locknut or set screw to penetrate
the paint and make a metal-to-metal contact.
o Don’t over bend cables when pulling them through a bend in a raceway, often a
pressure or squeezing develops causing insulation damage.
Electrical Hazard Mitigation - Prevention
Reducing and eliminating exposure to electrical hazards requires constant attention. Safety is
everyone's responsibility - employers and employees. A safe electrical environment makes good
personal as well as business sense.
Physical barriers (around energy source) such as fences and insulators on conductors
o Keep work areas clean and dry. Cluttered work areas and benches invite
accidents and injuries.
Management barriers - policy documents
o Who is responsible for electrical safety at the site?
o How is electrical safety dealt with at the site?
o How are people trained?
o What are the qualifications for people working on and around electrical
equipment?
Administrative barriers (driven by management) Implementation of policy documents
o Site and task specific
o Recognizing the hazards
o Guidelines on how to deal with electrical hazards.
Call for help (can't be handled by one person) and follow the emergency response system
as set forth in the safety procedures of each organization.
Get the approved first-aid supplies (these should be easily accessible when required).
De-energize the circuit.
Separate the person from the energy source.
Make sure you and the victim are in a safe zone - not in contact with any electrical source,
away from downed or broken wires.
Never grab the person or pull the person off the current with your hands; you might
become part of the circuit and become injured as well.
Use a dry wood broom, leather belt, plastic rope or something similar that is non-
conductive such as wood or plastic cane with hook on the end to free the person from the
energy source
Administer first aid2apply mouth-to-mouth resuscitation and/or CPR; know what to do
Keep the victim lying down, warm and comfortable to maintain body heat until help
arrives. Do not move the person in case of injury to neck or back.
If the victim is unconscious, put him/her on side to let fluids drain.
Make sure the victim receives professional medical attention (person shocked could have heart
failure hours later)
Burn victim first-aid steps:
o If the person's clothing is on fire, roll the person on the ground to smother the flames.
o Cool the burn with water or saline for a few minutes or until the skin returns to normal
temperature. Do not attempt to remove clothing that is stuck to a burn.
o Remove constricting items from the victim, such as shoes, belts, jewelry and tight
collars. They could continue to burn or cut off circulation if the victim experiences
swelling.
o Check the victim's breathing and heartbeat. Apply mouth-to-mouth resuscitation
and/or CPR if necessary.
o Keep victim warm and comfortable by covering him/her with clean, dry sheets or
blankets.
o Cover wounds with clean sheets and dry blankets.
o Elevate burned areas to reduce swelling.
An important way to reduce electrical shock accidents is to institute and follow established
procedures for preventive maintenance. This is the responsibility of the employer, employee and
owner - establishing a close working relationship to reduce and eliminate electrical accidents.