Professional Documents
Culture Documents
Selection guide
A little makes a big splash!
Contents It takes only a little of an additive from Dow to make the significant
performance difference your customers demand from your paint, ink and
2–3 Introduction coating formulations. DOWSIL™ and XIAMETER™ brand additives provide
4–9 Features, typical use problem-solving performance.
and properties of • Use in waterborne or solventborne formulations
additives from Dow
• Compatible with most binder systems
10–13 Additive selection trees
• High efficiency at low concentration levels to help lower raw
14–15 Additive selection table materials costs
16 Contact information • Suitable for use in low-VOC, sustainably formulated products
• Formulated for versatility and ease of use
Problem-solving performance
For more than half a century, Dow has led the way in silicon-based
technology and is a global leader in the development of problem-solving,
silicon-based technologies used in paints, inks and coatings. Many of our
additives impart a combination of benefits, giving you a high benefit-to-cost
ratio. Whether you need foam control; improved pigment dispersion, surface
wetting, leveling or adhesion; water resistance, mar resistance, slip, gloss or
texturization; or any combination of benefits, silicon-based technology from
Dow can help you achieve it.
pg 2
How to use this guide
dow.com/coatings gives you
This guide will help you explore the properties and performance capabilities
access to:
of our global line of additives for paints, inks and coatings. Table 1 groups
the additives by their primary benefit and describes their physical makeup, • Product samples
features, secondary benefits and properties. Table 2 highlights products
available in sample size via our Additive Sample Program. • Product literature and
technical datasheets
About concentrations and blending • Technical articles
The amount of additive required to achieve a particular benefit depends on • Customer service
the type of formulation, the solvent it contains, the resin system and total • The name of a technically
system solids. Generally, our additives are effective at the concentrations knowledgeable Dow
noted in Table 1. Since advantages do not increase proportionally, avoid distributor near you
using excess amounts. Additives from Dow are usually added during grind or
let-down, or they are post-added. However, some may be added during any
processing stage. See Table 1 for additional information.
pg 3
Table 1: Features, typical use and properties of additives from Dow[1] (Products are listed under their primary benefit)
pg 4
Viscosity at
Compatible Point of Typical Suitable Reactive Food contact
Product Description Features/benefits Solvent 25ºC (77ºF),
binder systems addition concentration[2] diluents[3] groups compliance[4]
cSt
Slip, mar resistance
Aromatics
Increases mar resistance of Solventborne acrylic, Grind,
Silicone polyether such as xylene Swiss Ordinance RS
DOWSIL™ solventborne coatings; also alkyd, amide, epoxy, let-down
copolymer; 0.1-0.5% or toluene; Carbinol Toluene 1.0-2.0 817.023.21 Annex 10
11 Additive improves leveling and gloss and nitrocellulose, polyester, or post
10% active mineral spirits Part A or B
prevents pigment separation polyurethane, vinyl add or ketones
Dispersion of high
molecular weight Provides slip and mar resistance Acrylic, polyester, Let-down Swiss Ordinance RS
DOWSIL™ polydimethylsiloxane in waterborne and solventborne polyurethane 250,000-
or post 0.1-1.0% Water None None 817.023.21 Annex 10
18 Additive and silicone coatings; anti-blocking in (waterborne and 650,000
add Part A or B
surfactant; 100% waterborne coatings solventborne)
active
Non-reactive silicone Effective at mar resistance and slip Water-based acrylic Let-down Water and
DOWSIL™ glycol copolymer; while maintaining gloss; reduced flexographic ink and U or post 0.1-1.0% suitable None None 275 FDA 176.210
27 Additive 100% active coefficient of friction V overprint varnish add solvents
Dispersion of high Imparts mar resistance and slip Waterborne acrylic, alkyd,
molecular weight Grind, let- Swiss Ordinance RS
DOWSIL™ to waterborne coatings; may also epoxy, nitrocellulose, 200,000-
polysiloxane and down or 0.05-3.0% Water Silanol Water 817.023.21 Annex 10
51 Additive provide room temperature polyester, polyurethane, 750,000
surfactants; post add Part A or B
anti-blocking vinyl
80% active
Viscosity at
Compatible Point of Typical Suitable Reactive Food contact
Product Description Features/benefits Solvent 25ºC (77ºF),
binder systems addition concentration[2] diluents[3] groups compliance[4]
cSt
Foam control
Fluorosilicones
Provides foam control with good Solventborne alkyd, 2K Grind, Methyl ethyl
DOWSIL™ Fluorosilicone; MEK and
balance between effectiveness polyurethane and let-down or 0.5-0.7% None ketone and Not available
102F Additive 1% active n-Propyl acetate
and compatibility epoxy paints post add n-Propyl acetate
Solventborne 1K silicone
DOWSIL™ Foam control agent in solvent- acrylic paint, acrylic Grind,
Fluorosilicone; MEK and Methyl ethyl
8621 based and radiation-curable/ dispersion paint, alkyd let-down or 0.1-1.0% None 0.94
5% active n-Propyl acetate ketone
Additive UV-curable coatings and radiation-curable post add
paint
Emulsions
Added
XIAMETER™ Silicone antifoam Good foam control and high directly or
AFE-0700 emulsion; 10% persistency over a wide pH Water-based systems during the 0.05-1.0% Water None None 1,750
Antifoam active and temperature range let-down
Emulsion stage
[1]
These values are not intended for use in preparing specifications.
[2]
The typical concentrations are usage levels where the materials have performed successfully. Usage levels can vary depending on application and performance requirements. Please evaluate for optimum performance in each specific application.
[3]
Review the Safety Data Sheet for each solvent prior to use. Safety Data Sheets can be obtained from your solvent supplier.
[4]
Complainant at effective date of publication of this selection guide. Visit dow.com/customersupport to obtain food contact regulatory information, including FDA, EU, Swiss Ordinance and German BfR clearance. FDA Title 21 CFR - 175 (175.105, 175.300,
175.320) Indirect food additives: adhesives and components of coatings; 176 (176.130, 176.170, 176.180, 176.200, 176.210) Indirect food additives: paper and paper board components; 177 (177.1390, 177.2600, 177.1520(b))
pg 5
Indirect food additives: polymers.
[5]
Use level not to exceed 0.015%.
Table 1: Features, typical use and properties of additives from Dow[1] (continued)
pg 6
Viscosity at
Compatible Point of Typical Suitable Reactive Food contact
Product Description Features/benefits Solvent 25ºC (77ºF),
binder systems addition concentration[2] diluents[3] groups compliance[4]
cSt
Foam control (continued)
Self-dispersible compounds
Provides foam control in waterborne
FDA 176.170 [6], Swiss
coatings, especially ink and Alcohols, glycol
DOWSIL™ Organo-modified silicone Let-down or Ordinance RS 817.023.21
clear wood coatings; balancing Waterborne acrylic 0.1-0.5% ethers and ester None None 350-900
71 Additive copolymer post add Annex 10 Part A or B, bfr 15-
effective foam control and surface alcohol
0002, bfr 36-0002
appearance
Waterborne acrylic
Can be added
Effective foam control for waterborne styrene emulsion paint,
DOWSIL™ Grind, directly or Swiss Ordinance RS
Silicone anti-foam compound coating and ink systems at low interior wall paint, flexo
8603 let-down or 0.05-1.0% pre-diluted None None 900-3,600 817.023.21 Annex 10 Part
with silica; 100% active dosages; tendency toward low gravure inks, polyester
Additive post add with alcohols or A or B
surface defects acrylic, acrylic-modified
polyglycols
alkyd
Release additives
Aromatic
FDA 175.105, 175.300,
DOWSIL™ hydrocarbons,
Provides release properties in clear Grind, 176.170, 176.180, 176.200,
1-9770 High viscosity, reactive ketones,
or pigmented coatings; can be used Polyester, silicones let-down or 0.1-5.0% Silanol None 11,000-14,000 176.210, 177.2260, 177.2800,
Release silicone fluid acetates and
in food contact applications post add 178.3120, 178.3570, 178.3910,
Additive other suitable
181.28, bfr 15-0002
solvents
[1]
These values are not intended for use in preparing specifications.
[2]
The typical concentrations are usage levels where the materials have performed successfully. Usage levels can vary depending on application and performance requirements. Please evaluate for optimum performance in each specific application.
[3]
Review the Safety Data Sheet for each solvent prior to use. Safety Data Sheets can be obtained from your solvent supplier.
[4]
Complainant at effective date of publication of this selection guide. Visit dow.com/customersupport to obtain food contact regulatory information, including FDA, EU, Swiss Ordinance and German BfR clearance. FDA Title 21 CFR - 175 (175.105, 175.300, 175.320) Indirect food additives: adhesives and
components of coatings; 176 (176.130, 176.170, 176.180, 176.200, 176.210) Indirect food additives: paper and paper board components; 177 (177.1390, 177.2600, 177.1520(b)) Indirect food additives: polymers.
[5]
Chemically equivalent to DOWSIL™ Z-6032 Silane.
[6]
Limitations may apply. Please contact Na.info@dow.com for more information.
[7]
Use level not to exceed 0.025%.
Table 1: Features, typical use and properties of additives from Dow[1] (continued)
Viscosity
Compatible Point of Typical Suitable Reactive at 25ºC Food contact
Product Description Features/benefits Solvent (77ºF),
binder systems addition concentration[2] diluents[3] groups compliance[4]
cSt
Adhesion promotion and surface treatment (substrates, pigments)
Improves pigment dispersion Aromatics
Solventborne
and reduces separation and Grind, let- such as xylene
DOWSIL™ Silanol-functional (Si-OH) additive; 10% acrylic, alkyd,
flotation in solventborne down or post 0.1-0.5% or toluene; Silanol Toluene 0.7-1.4
3 Additive active polyester, epoxy,
coatings; also provides leveling, add mineral spirits
polyurethane
flow-out and gloss or ketones
Titanium dioxide dispersant both Combine
DOWSIL™ for high-grade and low-grade Solventborne with resins
Alkoxy siloxane with organic group; Xylene and
700P TiO2; provides stabilization of inorganic filler before adding 0.02-4.0% Alkoxy Methanol 5.5
90% active butyl acetate
Additive pigment dispersion and prevents dispersant pigment for
pigment flooding and floating grinding
Improves adhesion of Grind for
Waterborne and Primer: dilute
DOWSIL™ waterborne and solventborne waterborne;
Aminoethylaminopropyltrialkoxysilane; solventborne to 10% active Alcohols Amino;
Z-6121 coatings when bonded to glass let-down or n-Butanol < 10 FDA 175.105
50% active acrylic, alkyd, epoxy, Additive: and water alkoxy-silyl
Silane or metal substrates; can be post add for
polyester 0.1-5.0%
used as an additive or primer solventborne
Primer: dilute
Adhesion promoter and Waterborne and
XIAMETER™ Grind, to 10% active
Aminoethylaminopropyltrimethoxysilane; pigment treatment in solventborne Alcohols Amino; FDA 175.105,
OFS-6020 let-down or in isopropanol None < 10
99% active waterborne and solventborne acrylic, alkyd, epoxy, and water methoxy-silyl 175.300
Silane post add Additive:
coatings polyurethane
0.5-2.0%
Improves adhesion of Waterborne and Primer: dilute to
XIAMETER™ waterborne, solventborne and solventborne acrylic, 0.1-0.5% active in
3-methacryloxypropyltrimethoxysilane; alkyd, epoxy, polyester,
Let-down or acidified (pH~4.0)
Alcohols Methacrylate;
OFS-6030 radiation-cured coatings to None 2.3-2.7 FDA 177.2465[7]
98% active polyurethane, vinyl;
post add water Additive:
and water methoxy-silyl
Silane inorganic substrates when used
as a primer or additive radiation-cured acrylic 0.1-3.0%
Primer: dilute
Adhesion promoter in with methanol
XIAMETER™ Waterborne and Grind, let- Amino;
Cationic vinylbenzyl and amino- waterborne and solventborne or ethanol mixed Alcohols
OFS-6032 solventborne acrylic, down or post vinylbenzyl; Methanol 1-3
functional methoxy-silane; 40% active coatings; can be used as an with water 10:1 and water
Silane[5] epoxy add methoxy-silyl
additive or primer Additive:
0.05-3.0 wt%
Adhesion promoter and Primer: dilute
Waterborne and FDA 177.1390,
XIAMETER™ pigment treatment in Grind, let- to 10% active
Glycidoxypropyltrimethoxysilane; solventborne acrylic, Alcohols Epoxy; Swiss Ordinance
OFS-6040 waterborne and solventborne down or post in isopropanol None 2.95-3.20
99% active alkyd, amine, epoxy, and water methoxy-silyl RS 817.023.21
Silane coatings; can be used as an add Additive:
polyurethane, vinyl Annex 10 Part B[8]
additive or primer 0.05-3.0%
Can be added
Bonds with inorganic surfaces Solventborne during Swiss Ordinance
XIAMETER™ through alkoxysilane; forms acrylic, alkyd, epoxy, solventborne Additive: Alcohols Vinyl; RS 817.023.21
OFS-6300 Vinyltrimethoxysilane; 99% active paint formulation
None 0.56
siloxane crosslinks via polyurethane; 0.05-1.0% and water methoxy-silyl Annex 10 Part
Silane moisture cure UV-curable epoxy at the pigment A or B
grind step
[1]
These values are not intended for use in preparing specifications.
[2]
The typical concentrations are usage levels where the materials have performed successfully. Usage levels can vary depending on application and performance requirements. Please evaluate for optimum performance in each specific application.
[3]
Review the Safety Data Sheet for each solvent prior to use. Safety Data Sheets can be obtained from your solvent supplier.
[4]
Complainant at effective date of publication of this selection guide. Visit dow.com/customersupport to obtain food contact regulatory information, including FDA, EU, Swiss Ordinance and German BfR clearance. FDA Title 21 CFR - 175 (175.105, 175.300, 175.320) Indirect food additives: adhesives and
components of coatings; 176 (176.130, 176.170, 176.180, 176.200, 176.210) Indirect food additives: paper and paper board components; 177 (177.1390, 177.2600, 177.1520(b)) Indirect food additives: polymers.
pg 7
[5]
Chemically equivalent to DOWSIL™ Z-6032 Silane.
[7]
This product is an unreacted monomer. May be copolymerized as stipulated in 177.2465(a).
[8]
May be used as an optional trimethoxysilane coupling agents in accordance with 177.1390 (c)(2)(iv)(a).
Table 1: Features, typical use and properties of additives from Dow[1] (continued)
pg 8
Viscosity
Compatible Point of Typical Suitable Reactive at 25ºC Food contact
Product Description Features/benefits Solvent
binder systems addition concentration[2] diluents[3] groups (77ºF), compliance[4]
cSt
Water resistance
Swiss Ordinance
Low-viscosity emulsion
DOWSIL™ Provides water resistance for waterborne Let-down RS 817.023.21
of silicone elastomer Mainly acrylics 1.0-5.0% Water Silanol Water 250-650
84 Additive systems, particularly inks or post add Annex 10 Part
precursors; 60% active
A or B
Medium-viscosity Swiss Ordinance
DOWSIL™ emulsion of silicone Provides water resistance for waterborne Let-down 34,000- RS 817.023.21
Mainly acrylics 1.0-5.0% Water Silanol Water
85 Additive elastomer precursors; systems, particularly inks or post add 46,000 Annex 10 Part
60% active A or B
Provides water repellency and water beading for
DOWSIL™ Emulsion; 38-44% Acrylic, styrene-acrylics and vinyl Let-down Ethoxy-
waterborne systems with minimal effect on water 1.0-5.0% Water Water 6
87 Additive actives acetate emulsions or post add silanol
vapor permeability; particularly for decorative paints
Provides water repellency with minimal effect
Aliphatic and Swiss Ordinance
on water vapor permeability; can be used in
DOWSIL™ Silane/siloxane blend; Let-down aromatic Alkoxy- RS 817.023.21
waterborne systems containing polar solvents Acrylic, styrene-acrylics 1.0-5.0% None 35
88 Additive 98% actives or post add hydrocarbons and silanol Annex 10 Part
and solventborne systems; particularly for
polar solvents A or B
decorative paints
General-purpose low-VOC hydrophobe to
DOWSIL™ Silicone emulsion; 60% improve water resistance and water contact Water-based acrylic, styrene Let-down Alkoxy;
901H 0.5-5.0% Water Water Not available
active angle; may provide corrosion resistance for acrylic and VAE systems or post add silanol
Additive waterborne industrial metal coating
Co-binder for high-PVC siloxane paints;
decreases water absorption through
DOWSIL™ Silicone-resin-based hydrophobization of pores; can be combined Water-based acrylic, styrene Let-down
902H 8.0-10.0% Water Alkoxy Water 300-2,000
emulsion; 50% active with a beading additive to additionally achieve acrylic and VAE systems or post add
Additive high water-contact angle; may provide dirt pick
up resistance
DOWSIL™ Provides snail trail resistance in high PVC (dark) Typical coalescent
Amino functional Acrylic and styrene acrylic high Grind or
904H colored paints and provides improved surface 1-5% used in architectural Amino None 70
polydimethylsiloxane pigmented paint let-down
Additive hydrophobicity and water repellency formulations
Leveling, gloss
Aromatics such
Aids deaeration without destabilizing the curtain Swiss Ordinance
Grind, as xylene, toluene,
DOWSIL™ Arylalkyl-modified in solventborne curtain coatings; improves Water-based acrylic, styrene RS 817.023.21
let-down or 0.05-0.5% mineral spirits and None None 1,125-1,645
56 Additive silicone; 100% active leveling and gloss; aids pigment orientation; acrylic and VAE systems Annex 10 Part
post add esters such as butyl
good thermostability A or B
acetate
FDA 176.170,
175.3001], Swiss
Acetone, toluene,
Improves leveling, slip, mar resistance and Grind, Ordinance RS
DOWSIL™ Silicone polyether (NOTE: Always check mineral spirits and
gloss in waterborne and solventborne coatings; let-down or 0.1-1.0% None None 175-390 817.023.21
57 Additive copolymer compatibility before usage) isopropyl alcohol;
provides substrate wetting post add Annex 10 Part B,
dispersible in water
bfr 15-0002, CN
9685.2016
Swiss Ordinance
Flow and leveling additive for solventborne and
DOWSIL™ Grind, Alcohols, glycol RS 817.023.21
Silicone polyether waterborne coatings; also lowers coefficient of Water-based acrylic, styrene
401LS let-down or 0.05-1.0% ethers and aromatic None None 100-250 Annex 10 Part
copolymer friction to improve slip and hand feel; compatible acrylic and VAE systems
Additive post add solvents B, bfr.15-0002,
with clear coats
bfr.36-0002
Effective flow and leveling additive for waterborne
Swiss Ordinance
DOWSIL™ and radiation curable systems; also lowers Alcohols, glycol
Silicone polyether (NOTE: Always check RS 817.023.21
402LS coefficient of friction, giving good slip; suitable Let-down 0.1-1.0% ethers and aromatic Carbinol None 280-400
copolymer compatibility before usage) Annex 10 Part
Additive in pigmented and clear coat formulations; also solvents
A or B
provides anti-blocking and applied hiding
Solvent-based acrylic, epoxy,
DOWSIL™ Carbinol-functional Provides leveling and slip with good compatibility polyester and urethane systems; Grind,
Water, alcohols,
8526 silicone polyether;100% in solventborne, waterborne and UV-curable waterborne acrylic, polyester, let-down or 0.2-1.0% Carbinol None 1,552
toluene, xylene
Additive active coatings, inks and overprint varnishes epoxy and urethane systems; UV post add
systems
[1]
Limitations may apply. Please contact www.dow.com/contactus for more information.
Table 1: Features, typical use and properties of additives from Dow[1] (Products are listed under their primary benefit)
Typical Viscosity
Compatible Point of Suitable Reactive Food contact
Product Description Features/benefits concen- Solvent at 25ºC
binder systems addition diluents[3] groups compliance[4]
tration[2] (77ºF), cSt
Wetting
Imparts spreading and wetting in waterborne
Swiss
and radiation-curable coatings on difficult Isopropyl
Waterborne acrylate, Ordinance RS
DOWSIL™ substrates, e.g., low-energy substrates such Let-down or alcohol, acetone;
Silicone polyether copolymer alkyd, polyester, 0.1-0.4% Carbinol None 31-51 817.023.21
67 Additive as polyethylene, polypropylene, polyester; post add dispersible
polyurethane Annex 10 Part
suitable in inks, decorative and industrial in water
A or B
coatings for plastic, metal and wood
Imparts enhanced substrate wetting in Isopropyl
Waterborne acrylic
DOWSIL™ waterborne and radiation curable systems; alcohol, acetone
and polyurethane;
500W Silicone polyether copolymer suitable across a wide range of substrates, Let-down 0.1-0.4% and toluene; None None 25.5-29.5
radiation-curable
Additive including wood and plastics; stable at high dispersible
acrylate
pH in water
Isopropyl Swiss
Imparts enhanced substrate wetting in Waterborne acrylic
DOWSIL™ alcohol, acetone Ordinance RS
waterborne and radiation curable systems; and polyurethane;
501W Silicone polyether copolymer Let-down 0.1-0.4% and toluene; None None 10-30 817.023.21
suitable across a wide range of substrates, radiation-curable
Additive dispersible Annex 10
including wood and plastics acrylate
in water Part B
Isopropyl Swiss
Imparts enhanced substrate wetting in Waterborne acrylic
DOWSIL™ alcohol, acetone Ordinance RS
waterborne and radiation curable systems; and polyurethane;
502W Silicone polyether copolymer Let-down 0.1-0.4% and toluene; Carbinol None 49-75 817.023.21
suitable across a wide range of substrates, radiation-curable
Additive dispersible Annex 10
including wood and plastics acrylate
in water Part B
Designed to provide wetting, prevent
DOWSIL™ pinholing and improve film surface Acrylic latexes,
Let-down or Water and 1500-2000 bfr 15-0002,
503W Silicone glycol copolymer appearance in solventborne and waterborne polyurethane 0.1-1% None None
post add alcohols cP bfr 36-0002
Additive inks, paints and coatings applications; dispersions
reduced foam generation
Texturing (matting and/or tactile effects)
Best added to
a portion of the
Powder consisting of Solvents such
resin/solvent Swiss
transparent spherical silicone as glycols, glycol
DOWSIL™ Imparts mar and abrasion resistance with Waterborne and system under Ordinance RS
elastomer particles with ethers, alcohols,
23 N a smooth, matte finish to waterborne and solventborne acrylic, high shear 0.5-5.0% Epoxy None NA 817.023.21
epoxy functionality; average water with
Additive solventborne coatings polyurethane conditions prior Annex 10 Part
particle diameter of 1-3 cosolvents such
to blending A or B
microns as acetone
into the final
formulation
Waterborne suspension of
spherical silicone elastomer
DOWSIL™ particles with epoxy Imparts a silky, smooth, matte finish to Waterborne acrylic,
Post add 2-10% Water Epoxy Water <150
33 Additive functionality; median particle waterborne coatings polyurethane
diameter of 3-4 microns;
46% active
Aromatic
DOWSIL™ Primarily Final thinning solvents such as
Imparts a hammertone finish to metal 0.05- Ethylbenzene,
61 Paint 10% silicone in solvent solventborne; stage or prior to xylene or toluene, None 120
surfaces 0.5% xylene
Additive some waterborne let-down mineral spirits, or
ketones
[1]
These values are not intended for use in preparing specifications.
[2]
The typical concentrations are usage levels where the materials have performed successfully. Usage levels can vary depending on application and performance requirements. Please evaluate for optimum performance in each specific application.
[3]
Review the Safety Data Sheet for each solvent prior to use. Safety Data Sheets can be obtained from your solvent supplier.
[4]
Complainant at effective date of publication of this selection guide. Visit dow.com/customersupport to obtain food contact regulatory information, including FDA, EU, Swiss Ordinance and German BfR clearance. FDA Title 21 CFR - 175 (175.105, 175.300,
175.320) Indirect food additives: adhesives and components of coatings; 176 (176.130, 176.170, 176.180, 176.200, 176.210) Indirect food additives: paper and paper board components; 177 (177.1390, 177.2600, 177.1520(b)) Indirect food
additives: polymers.
NA = Not Applicable
pg 9
Additive selection tree for coatings applications
DOWSIL™ 18 Additive
DOWSIL™ 23 N Additive
DOWSIL™ 29 Additive
DOWSIL™ 57 Additive
DOWSIL™ 67 Additive
Solventless UV-cure/ DOWSIL™ 100F Additive
EB-cure system DOWSIL™ 102F Additive
Start DOWSIL™ 163 Additive
DOWSIL™ 205SL Additive1
DOWSIL™ 402LS Additive
DOWSIL™ 500W Additive
DOWSIL™ 501W Additive
DOWSIL™ 502W Additive
DOWSIL™ 8526 Additive
DOWSIL™ 8621 Additive
Solvent Waterborne DOWSIL™ 8628 Additive
Systems system
FDA compliant DOWSIL™ 3 Additive DOWSIL™ 14 Additive
DOWSIL™ 11 Additive DOWSIL™ 29 Additive
DOWSIL™ 14 Additive Leveling DOWSIL™ 57 Additive
DOWSIL™ 27 Additive DOWSIL™ 29 Additive DOWSIL™ 401LS Additive
DOWSIL™ 57 Additive Leveling DOWSIL™ 56 Additive DOWSIL™ 402LS Additive
DOWSIL™ 62 Additive DOWSIL™ 57 Additive DOWSIL™ 8526 Additive
DOWSIL™ 71 Additive DOWSIL™ 401LS Additive
DOWSIL™ 74 Additive DOWSIL™ 8526 Additive
DOWSIL™ 163 Additive DOWSIL™ 503W Additive DOWSIL™ 14 Additive
DOWSIL™ Z-6121 Silane Mar DOWSIL™ 18 Additive
XIAMETER™ OFS-6011 Silane resistance/ DOWSIL™ 27 Additive
XIAMETER™ OFS-6020 Silane Mar DOWSIL™ 11 Additive slip DOWSIL™ 51 Additive
XIAMETER™ OFS-6030 Silane resistance/ DOWSIL™ 14 Additive DOWSIL™ 52 Additive
XIAMETER™ OFS-6032 Silane slip DOWSIL™ 29 Additive DOWSIL™ 54 Additive
XIAMETER™ OFS-6040 Silane DOWSIL™ 54 Additive DOWSIL™ 57 Additive
DOWSIL™ 55 Additive DOWSIL™ 205SL Additive
DOWSIL™ 57 Additive DOWSIL™ 210S Additive
DOWSIL™ 205SL Additive DOWSIL™ 211S Additive
Pigment
Pigment DOWSIL™ 3 Additive treatment XIAMETER™ OFS-6011 Silane
treatment DOWSIL™ 700P Additive XIAMETER™ OFS-6020 Silane
XIAMETER™ OFS-6020 Silane XIAMETER™ OFS-6040 Silane
XIAMETER™ OFS-6030 Silane
XIAMETER™ OFS-6040 Silane
Texturing
DOWSIL™ 23 N Additive
Gloss DOWSIL™ 33 Additive
DOWSIL™ 57 Additive
Solventborne
Solvent Waterborne
DOWSIL™ 62 Additive
DOWSIL™ 71 Additive
systems systems
DOWSIL™ 74 Additive
DOWSIL™ 163 Additive
DOWSIL™ 7 Additive
DOWSIL™ 100F Additive
DOWSIL™ 102F Additive
DOWSIL™ 163 Additive
DOWSIL™ 8621 Additive
Waterborne
< 60% PVC3 paints > 60% PVC3 paints
DOWSIL™ 62 Additive and inks
DOWSIL™ 71 Additive
DOWSIL™ 74 Additive
Emulsions
XIAMETER™ AFE-0700
Self-dispersible Antifoam Emulsion
compounds Emulsions
Recommended
0.1-0.5% 0.1-0.4% 0.05-0.2% 0.05-0.2%
use level
pg 11
Mar-resistant/slip additive selection tree for coatings applications
Multipurpose;
may also improve Best leveling
To improve wetting, combine with And wetting
wetting and leveling
DOWSIL™ 57 Additive DOWSIL™ 57 Additive
DOWSIL™ 29 Additive
DOWSIL™ 57 Additive
DOWSIL™ 402LS Additive
Best mar
Best mar Resistance and slip
Resistance and slip Anti-blocking
DOWSIL™ 18 Additive
Solventless uv-cure/ DOWSIL™ 27 Additive DOWSIL™ 18 Additive
DOWSIL™ 18 Additive
Eb-cure system DOWSIL™ 57 Additive DOWSIL™ 52 Additive
DOWSIL™ 8526 Additive
DOWSIL™ 18 Additive Best wetting
Low foam DOWSIL™ 29 Additive
DOWSIL™ 57 Additive DOWSIL™ 57 Additive
DOWSIL™ 54 Additive DOWSIL™ 205SL Additive Defoaming
DOWSIL™ 402LS Additive
DOWSIL™ 205SL Additive
Hand feel
DOWSIL™ 52 Additive
Solventborne
DOWSIL™ 11 Additive
DOWSIL™ 14 Additive Waterborne
DOWSIL™ 18 Additive
DOWSIL™ 29 Additive
DOWSIL™ 14 Additive DOWSIL™ 55 Additive
DOWSIL™ 54 Additive
DOWSIL™ 27 Additive DOWSIL™ 57 Additive
DOWSIL™ 55 Additive
DOWSIL™ 57 Additive Start DOWSIL™ 29 Additive
DOWSIL™ 51 Additive
DOWSIL™ 205SL Additive
DOWSIL™ 401LS Additive
DOWSIL™ 205SL Additive
DOWSIL™ 52 Additive DOWSIL™ 402LS Additive
DOWSIL™ 401LS Additive
Best mar
Best leveling and Resistance and slip To improve wetting, combine with
wetting
DOWSIL™ 67 Additive
DOWSIL™ 51 Additive DOWSIL™ 500W Additive
DOWSIL™ 57 Additive DOWSIL™ 52 Additive DOWSIL™ 501W Additive
DOWSIL™ 401LS Additive DOWSIL™ 502W Additive
DOWSIL™ 503W Additive
Easy to incorporate
DOWSIL™ 52 Additive
DOWSIL™ 210S Additive
DOWSIL™ 211S Additive
pg 12
Leveling and wetting additive selection tree for coatings and ink applications
Recoatable
DOWSIL™ 11 Additive
Multipurpose;
Multipurpose; Also gives mar
Also gives mar Resistance and slip
Resistance and slip
DOWSIL™ 14 Additive
DOWSIL™ 11 Additive DOWSIL™ 29 Additive
FDA compliant DOWSIL™ 57 Additive
DOWSIL™ 14 Additive
DOWSIL™ 29 Additive DOWSIL™ 57 Additive DOWSIL™ 401LS Additive
DOWSIL™ 55 Additive DOWSIL™ 402LS Additive
DOWSIL™ 57 Additive DOWSIL™ 8526 Additive
DOWSIL™ 401LS Additive
DOWSIL™ 8526 Additive
Solventborne Waterborne
DOWSIL™ 57 Additive
pg 13
Table 2. Additive selection table
Use this chart to identify the additives that meet your performance requirements.
)
effects
nd trim
slip
ING
R)
E
etting
r tactile
HE
NC
nd
ETT
E
l wall
ood a
(OT
ance a
E
IAL er)
STA
UR
L
RN
ELI g and w
RO
e
NE
&W
& O opvs
US l (oth
DIA n cur
VE borne
cking
NC
g and/o
AM ontro
PVS
SI
ectura
BO
NT
ATE borne
trial w
OR
E
NG
resist
TIO
NT
RR
TR
CO
(mattining
dustria
ksS and
RB
RAadiatio
A T E se
nti-blo
SSOoLlvent
FFOoam c
LLEeVvelin
Water
Archit
Textur
Relea
Indus
Mar
ND
NK
IIn
IIn
R
A
W
W
DOWSIL™ 11 Additive
DOWSIL™ 14 Additive
DOWSIL™ 18 Additive
DOWSIL™ 27 Additive
DOWSIL™ 29 Additive
DOWSIL™ 51 Additive
DOWSIL™ 52 Additive
DOWSIL™ 54 Additive
DOWSIL™ 55 Additive
DOWSIL™ 7 Additive1
DOWSIL™ 62 Additive
DOWSIL™ 68 Additive
DOWSIL™ 71 Additive
DOWSIL™ 74 Additive
pg 14
Table 2. Additive selection table (continued)
)
effects
im
slip
ING
and tr
CE
& W ting
r tactile
nd
ment
ETT
TAN
E
l wall
et
ce
ance a
E
ther)
UR
ood
RN
ELI g and w
RO
e
TER istan
NE
opvs
SIS
t treat
DIA n cur
VE borne
g
l
NC
g and/o
AM ontro
ectura
BO
lockin
trial (o
NT
ATE borne
trial w
OR
RE
NG
resist
TIO
res
NT
CO
(mattin g
nd
RB
RRAadiatio
igmen
in
SSOoLlvent
FOoam c
LLEeVvelin
Hiding
Anti-b
Inks a
Water
Water
Archit
Textur
Indus
Indus
Mar
A
P
W
W
F
DOWSIL™ 3 Additive
DOWSIL™ 84 Additive
DOWSIL™ 85 Additive
DOWSIL™ 87 Additive
DOWSIL™ 88 Additive
DOWSIL™ 56 Additive
DOWSIL™ 57 Additive
DOWSIL™ 23 N Additive
DOWSIL™ 33 Additive
DOWSIL™ 67 Additive
pg 15
Your global connection
At home or abroad – wherever your business takes
you – you will find the product supply, customer service
and technical support you need to succeed available
locally from Dow.
Whether you are facing a challenge that could benefit
from Dow’s international business and market experience
or you need a reliable, local source of supply for
innovative paints, inks and coatings solutions, contact
your Dow representative. Product samples, technical
information and assistance also are available online at
dow.com/coatings.