Professional Documents
Culture Documents
Standard Terminology
Relating to Metallic Coated Steel Products1
This standard is issued under the fixed designation A902; the number immediately following the designation indicates the year of
original adoption or, in the case of revision, the year of last revision. A number in parentheses indicates the year of last reapproval. A
superscript epsilon (´) indicates an editorial change since the last revision or reapproval.
1. Scope* 3. Terminology
1.1 This standard is a compilation of terminology related to 3.1 Definitions:
metallic coatings used in the steel industry, and to the steel on aluminized coating, n—a coating on steel consisting of either
which the coatings are applied. Terms that are generally commercially-pure aluminum (Type 2) or aluminum-silicon
understood or adequately defined in other readily available alloy (Type 1), applied by the hot-dip process. (2005)
sources are not included.
barb, n—as related to barbed wire, a short length of wire, with
1.2 When a term is used in an ASTM document for which exposed ends cut on a bias to produce sharp points. (1995)
Committee A05 is responsible it is included herein only when
judged, after review by Subcommittee A05.18, to be a gener- barbed wire, n—a fabricated wire product consisting of two
ally usable term. line wires twisted to form a two-wire strand, into which
2-point or 4-point barbs are tightly wrapped and locked into
1.3 Definitions that are identical to those published by other
place at specified intervals. (1995)
ASTM committees or other standards organizations are iden-
tified with the ASTM standard designation (for example, base metal, n—as related to metallic-coated steel, the steel to
Terminology B374) or with the abbreviation of the name of the which the coating is applied, as distinguished from the
organization. coating metal. (1990)
1.4 A definition is a single sentence with additional infor- batch coating, n—of metallic coated steel products, the
mation included in notes. The year the definition was adopted, process of discontinuous-sequential passage of steel articles
or the year of latest revision, is appended. The responsible through the various steps of the coating process, such as,
subcommittee reviews the definition for each term at five-year cleaning, pickling, fluxing, and coating. (1995)
intervals, and prepares revisions as needed.
breaking strength, n—as related to wire, the maximum force
2. Referenced Documents developed prior to fracture during tension testing of wire and
2.1 ASTM Standards:2 wire products.
A641/A641M Specification for Zinc–Coated (Galvanized) DISCUSSION—In testing of stranded wire products, the maximum
force may be developed after fracture of one or more individual wires.
Carbon Steel Wire
(1993)
A924/A924M Specification for General Requirements for
Steel Sheet, Metallic-Coated by the Hot-Dip Process carbon steel, n—steel having a maximum carbon content of
B374 Terminology Relating to Electroplating 2.0 % and a composition conforming to the following: (1) no
D6386 Practice for Preparation of Zinc (Hot-Dip Galva- minimum content is specified for chromium, cobalt, colum-
nized) Coated Iron and Steel Product and Hardware bium (niobium), molybdenum, nickel, titanium, tungsten,
Surfaces for Painting vanadium, zirconium, or any other element added to obtain
D7396 Guide for Preparation of New, Continuous Zinc- a desired alloying effect; (2) the specified minimum and
Coated (Galvanized) Steel Surfaces for Painting maximum values for copper do not exceed 0.35 % and
0.60 %, respectively; (3) the specified maximum for any of
the following elements does not exceed these percentages:
1
This terminology is under the jurisdiction of ASTM Committee A05 on manganese 1.65 %, silicon 0.60 %, columbium (niobium)
Metallic-Coated Iron and Steel Products and is the direct responsibility of
Subcommittee A05.18 on Editorial and Terminology. 0.015 %, vanadium 0.008 %, boron 0.0008 %, or titanium
Current edition approved Nov. 1, 2013. Published November 2013. Originally 0.025 %; and (4) the incidental content of the following
approved in 1990. Last previous edition approved in 2013 as A902 - 13a. DOI: elements does not exceed these percentages: nickel, 0.20 %;
10.1520/A0902-13B.
2
For referenced ASTM standards, visit the ASTM website, www.astm.org, or
chromium, 0.15 %; and molybdenum, 0.06 %.
contact ASTM Customer Service at service@astm.org. For Annual Book of ASTM DISCUSSION—Carbon steels typically contain small quantities of
Standards volume information, refer to the standard’s Document Summary page on certain residual elements from the feed materials. When the quantity of
the ASTM website. such retained elements exceeds the values listed in (4) above, the
APPENDIXES
(Nonmandatory Information)
X1.1 The following keywords are recommended for use as polymer coated steel sheet
determined appropriate by the subcommittee responsible for polymer coatings
the standard. Other keywords may be used as necessary. steel sheet—aluminum coated
X1.1.1 General for All Standards:— steel sheet—55 % aluminum-zinc alloy coated
aluminum coatings steel sheet—polymer coated
coatings—aluminum steel sheet—terne coated
coatings—55 % aluminum-zinc alloy steel sheet—zinc coated (electrolytic process)
coatings—metallic steel sheet—zinc coated (hot dip process)
coatings—zinc steel sheet—zinc-5 % aluminum-mischmetal coated
coatings—zinc-5 % aluminum alloy steel sheet—zinc-5 % aluminum-magnesium coated
coatings—zinc-5 % aluminum-mischmetal zinc coatings—steel sheet
galvanized coatings [see zinc coatings] X1.1.4 Related to Steel Wire:
steel products—metallic coated aluminum coatings—steel wire products
zinc coatings copper clad steel wire
zinc-5 % aluminum alloy coatings fencing material
X1.1.2 Related to Testing: fences/fencing—chain link
coating thickness fences/fencing—farm/field
coating weight [mass] metallic coated steel wire
steel wire—aluminum coated
X1.1.3 Related to Steel Sheet:
aluminum coatings—steel sheet steel wire—copper clad
coatings—composite steel wire—zinc coated
coatings—polymer steel wire—zinc-5 % aluminum-mischmetal coated
coatings—terne metal steel wire rope
coatings—zinc-5 % aluminum-mischmetal steel wire strand
coatings—zinc-5 % aluminum-magnesium zinc coatings—steel wire products
electrodeposited coatings X1.1.5 Related to Steel Fabricated Products:
metallic coated steel sheet coatings—zinc
X2.1 The following terms are defined in individual stan- A792/A792M Specification for Steel Sheet, 55%
dards under the jurisdiction of Committee A05, and are Aluminum-Zinc Alloy-Coated by the Hot-Dip Process
applicable only to the specific document (or documents) in A796/A796M Practice for Structural Design of Corrugated
which the term is defined. Definitions are not necessarily the Steel Pipe, Pipe-Arches, and Arches for Storm and Sanitary
same when a term is listed in two or more documents. Sewers and Other Buried Applications
A798/A798M Practice for Installing Factory-Made Corru-
X2.2 Referenced Documents gated Steel Pipe for Sewers and Other Applications
X2.2.1 ASTM Standards: A123/A123M Specification for A807/A807M Practice for Installing Corrugated Steel
Zinc Hot-Dip Galvanized Coatings on Iron and Steel Products Structural Plate Pipe for Sewers and Other Applications
A116 Specification for Metallic-Coated, Steel-Woven A809 Specification for Aluminum-Coated (Aluminized)
Wire Fence Fabric Carbon Steel Wire
A818 Specification for Coppered Carbon Steel Wire
A143 Practice for Safeguarding Against Embrittlement of
Hot-Dip Galvanized Structural Steel Products and Procedure A824 Specification for Metallic-Coated Steel Marcelled
for Detecting Embrittlement Tension Wire for Use With Chain Link Fence
A849 Specification for Post-Applied Coatings, Pavings,
A153/A153M Specification for Zinc Coating (Hot-Dip) on
and Linings for Corrugated Steel Sewer and Drainage Pipe
Iron and Steel Hardware
A855/A855M Specification for Zinc-5 % Aluminum-
A308 Specification for Steel Sheet, Terne Lead-Tin Alloy
Mischmetal Alloy-Coated Steel Wire Strand
Coated by the Hot-Dip Process
A875/A875M Specification for Steel Sheet, Zinc-5 Alumi-
A390 Specification for Zinc-Coated Galvanized Steel
num Alloy-Coated by the Hot-Dip Process
Poultry Fence Fabric Hexagonal and Straight Line
A929/A929M Specification for Steel Sheet, Metallic-
A475 Specification for Zinc-Coated Steel Wire Strand
Coated by the Hot-Dip Process for Corrugated Steel Pipe
A586 Specification for Zinc-Coated Parallel and Helical A930 Practice for Life-Cycle Cost Analysis of Corrugated
Steel Wire Structural Strand Metal Pipe Used for Culverts, Storm Sewers, and Other Buried
A653/A653M Specification for Steel Sheet, Zinc-Coated Conduits
Galvanized or Zinc-Iron Alloy-Coated Galvannealed by the A964/A964M Specification for Corrugated Steel Box Cul-
Hot-Dip Process verts
A740 Specification for Hardware Cloth (Woven or Welded A974 Specification for Welded Wire Fabric Gabions and
Galvanized Steel Wire Fabric) Gabion Mattresses (Metallic Coated or Polyvinyl Chloride
A742/A742M Specification for Steel Sheet, Metallic (PVC) Coated)
Coated and Polymer Precoated for Corrugated Steel Pipe A975 Specification for Double-Twisted Hexagonal Mesh
A754/A754M Test Method for Coating Weight Mass of Gabions and Revet Mattresses (Metallic Coated Steel Wire or
Metallic Coatings on Steel by X-Ray Fluorescence Metallic Coated Steel Wire with Polyvinyl Chloride (PVC)
A755/A755M Specification for Steel Sheet, Metallic Coating)
Coated by the Hot-Dip Process and Prepainted by the Coil- A978/A978M Specification for Composite Ribbed Steel
Coating Process for Exterior Exposed Building Products Pipe, Precoated and Polyethylene Lined for Gravity Flow
A760/A760M Specification for Corrugated Steel Pipe, Sanitary Sewers, Storm Sewers, and Other Special Applica-
Metallic-Coated for Sewers and Drains tions
A761/A761M Specification for Corrugated Steel Struc- A979/A979M Specification for Concrete Pavements and
tural Plate, Zinc-Coated, for Field-Bolted Pipe, Pipe-Arches, Linings Installed in Corrugated Steel Structures in the Field
and Arches A998/A998M Practice for Structural Design of Reinforce-
A762/A762M Specification for Corrugated Steel Pipe, ments for Fittings in Factory-Made Corrugated Steel Pipe for
Polymer Precoated for Sewers and Drains Sewers and Other Applications
black—A123/A123M fade—A755/A755M
SUMMARY OF CHANGES
Committee A05 has identified the location of selected changes to this standard since the last issue (A902 - 13a)
that may impact the use of this standard. (November 1, 2013)
Committee A05 has identified the location of selected changes to this standard since the last issue (A902 - 13)
that may impact the use of this standard. (June 1, 2013)
ASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentioned
in this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the risk
of infringement of such rights, are entirely their own responsibility.
This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years and
if not revised, either reapproved or withdrawn. Your comments are invited either for revision of this standard or for additional standards
and should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of the
responsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you should
make your views known to the ASTM Committee on Standards, at the address shown below.
This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,
United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the above
address or at 610-832-9585 (phone), 610-832-9555 (fax), or service@astm.org (e-mail); or through the ASTM website
(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/
COPYRIGHT/).