Professional Documents
Culture Documents
BS121FE
Step①
BS121FE
1
2
TRUE WIRELESS EARBUDS 3
4 Erect headset and place
User Manual them into the cochlea
should TRUE WIRELESS EARBUDS should be used with the compatible devices
which support Bluetooth wireless technology. This allows you to
make two calls and enjoy the music streaming at any time freely. Use the USB cable to connect with
Please read this user manual carefully before using the EARBUDS, mobile phone charger
and also read your device’s user manual regarding the Bluetooth
function, and pay attention to those important safety and R Step② Note 1: Check the charging device is suit to the headset or not.
Note 2: Use only the supplied charger to charge the headset, if use
maintenance information. L
6 7 Slightly rotate headset until it firm other device may violate the validation or the maintenance
Please keep the headset away from children. article of this product and may cause danger.
5 Note 3: Do not attempt to force open the built-in battery as this could
damage the headset.
1)MFB(multifunction button) 5)ON/OFF Note 4: A fully charged headset will lose its power automatically if left
2)Indicator light and MIC 6)Charging indicator unused. It is recommended to charge the headset each three
months.
3)Speaker 7)Micro USB charging port Note 5: Do not leave the headset in a too hot or too cold condition (best
4)The charging contact point between -10℃ and 50℃) which may affect the headset's operations
although it is fully charged.
Step③ Note 6: Do not dispose of the headset into fire or wate
r.
Specifications Make the headset to cochlear edge tightly.
Note 7: Please take out of the headsets from the charging base and store it
separately if not to use for a long time .
Bluetooth Version: V4.2 Status No. Status Headset Performance
Bluetooth Profiles Supported: HSP, HFP, A2DP, AVRCP, TWS
1 The Single Pairing The indicator light of headset(R) flashes red and blue Turning ON/OFF
alternately.
Audio Decoding Protocol: SBC, AAC After TWS pairing successed, the indicator light of right
Transmission Power: Class 2 2 TWS Pairing
headset alternately flashing red and blue, when the right
headset pairing successful with mobile phone, the
indicator light flashes blue once every 5 seconds
Method
Operation Range: Up to 10 meters The indicator light of right headset flashes blue once every In OFF MODE, press and hold MFB for 2 seconds to turn on.
3 Standby Mode
5 seconds In ON MODE, press and hold MFB for 5 seconds to turn off.
Frequency Range: 2.4GHz-2.48GHz When in a call, the indicator light of right headset flashes
4 Call State
red every 5 seconds
Battery of Headset: 45mAH Li-polymer Battery X2
Headset Charging The indicator light of headset is red when being charged,
Charging Voltage of Headset: 5V 5 State and will turn off automatically after being fully charged
2s On standby mode, shortly press MFB to play On OFF MODE state, press MFB button for 10 seconds (OFF
music. MODE→ON MODE(2 seconds)→Delete pairing records (10
On music playing state, shortly press MFB to seconds), until hearing the Beep voice for 3 times, and the
PLAY music, press MFB again to PAUSE music. red/blue light flashes twice at the same time.
Maintenance
On OFF state, press MFB key for 2 seconds to power on and
waiting for 10 seconds , the two headsets will enter pairing • Do not use abrasive cleaning solvents to clean the headset.
mode automatically. Two headsets connected with each other • Do not allow the headset to touch with any sharp objects as this will cause
after few seconds, the headset (R) alternately flashing red and Answering /Ending a Call Headset(R) scratching and damage
blue, and then open the phone's bluetooth device to search. • Please keep headset away from high-temperature, humidity and dust.
On standby state or call state, you can answer/end the call by shortly
press MFB of the headset(R).
Do as the above ways: 1 or 2 , after TWS successfully paired: Press and hold MFB of headset(R) for 2
The two headsets TWS
pairing failure/TWS paired Too many pairing records Delete pairing records according
left headset prompts "left channel" and right headset prompts "right seconds to reject the call, the speaker prompts successful but can not find to user manual
channel-pairing" “beep” twice and “call reject”. the headset(R)
Charging base without
Cell phone begines to search for bluetooth indicator light when
DC power supply doesn’t Check whether the micro USB
output power charging line is plugged or the
devices (see the user guide of your phone charging power switch is on
for instructions). Mobile phone to search Headsets without
1)Checking headset charging interface
Bluetooth ON The headsets couldn’t being whether has touched to POGO PIN of
for “BS121FE-R” and select the indicator light when
charged in charging base
charging base and the location is
BS121FE-R charging correct or not.
“BS121FE-R”.
The Last Number Redialing Headset(R)
2)Charging for charging base
Turning off Low battery Charging headset for 2-3 hours
automatically
On standby state or call state, shortly press
Headset echo Volume is too loud or Adjust the volume at phone or
MFB twice to redial the last phone number. The environment is noisy change a place
speaker will prompt "beep" twice and "redial". Environmental interference Change a place or move to
Noise in call caused or distance between close the headset and mobile
Connect headset and mobile is too far
Low voive of the calling Adjusting wearing position of
Wearing headset is wrong
party headset
The headset reconnected The charging base without Charging for charging base
with mobile phone after put power, the headset will auto turn
back to the charging base on and paired
-Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Changes or modifications not expressly approved by the party responsible for compliance
could void the user's authority to operate the equipment. This device complies with Part
(2) this device must accept any interference received, including interference that may