Professional Documents
Culture Documents
Introduction
Specifications
Battery powered 3.6V Lithium thionyl chloride (LiSOCl2) batteries non rechargeable, size D
Power 24 Vdc Wired Power (option) - For I.S. Application: 21 V to 25 Vdc Operated with
MTL7728P+ barrier (252 Ohms Max. end to end resistance), Max input current 26mA.
For Non I.S. application: 11 V to 30 Vdc Input range, Max input current 100mA.
1
For model STGW944 with CTFE fill fluid, the rating is –15 to 70°C (5 to 158°F); for model STGW94L, 97L, 98L and 99L with
CTFE fill fluid, the rating is –15 to 110°C (5 to 230°F).
2
For models STGW94L, STGW97L, STGW98L and STGW99L the upper limit is 110°C (230°F).
3
Short term equals 2 hours at 70°C (158 °F)
** The Ambient Limits shown are for Ordinary Non-Hazardous locations only. Refer to the appropriate
Control Drawing, FM/CSA, ATEX, or IECEx for the Ambient Limits when installed in Hazardous
Locations.
34-XY-03-24
Page 3
Wireless Specifications
Parameter Description
Wireless 2,400 to 2,483.5 MHz (2.4 GHz) Industrial, Scientific and Medical (ISM) band
Communication FHSS Selection – Frequency Hopping Spread Spectrum
DSSS Selection – Direct Sequential Spread Spectrum per FCC 15.247 / IEEE 802.15.4–2006.
ISA100.11a Compliant (2.4 GHz Direct Sequence Spread Spectrum 802.15.4 DSSS-FH)
Every data packet transmitted in either direction is verified (CRC check) and acknowledged by the
receiving device.
USA – FCC Certified
Canada – IC Certified
European Union – RTTE/ETSI Conformity
Japan – Ministry of Internal Affairs and Communications Certified (DSSS Selection only)
ISA100.11a RF NA Selection – 125 mW (20.9 dBm) maximum transmit power not including antenna per FCC/IC, or
Transmitter 400 mW (26.0 dBm) maximum EIRP including antenna for USA and Canadian locations.
Power (Optional) EU Selection – 10 mW (10.0 dBm) maximum EIRP including antenna per RTTE/ETSI for EU
locations.
FHSS RF NA Selection – 125 mW (20.9 dBm) maximum transmit power not including antenna per FCC/IC, or
Transmitter 400 mW (26.0 dBm) maximum EIRP including antenna for USA and Canadian locations.
Power (Optional) EU Selection – 100 mW (20.0 dBm) maximum EIRP including antenna per RTTE/ETSI for EU
locations.
DSSS RF NA Selection – 125 mW (20.9 dBm) maximum transmit power not including antenna per FCC/IC, or
Transmitter 400 mW (26.0 dBm) maximum EIRP including antenna for USA and Canadian locations.
Power (Optional) EU Selection – 10 mW (10.0 dBm) maximum EIRP including antenna per RTTE/ETSI for EU
locations.
JP Selection – 12.14 dBm/MHz [32mW (15.14 dbm)] maximum EIRP including antenna for
Japanese locations.
Data PV Publish Cycle Time: Configurable as 1, 5, 10 or 30 seconds
Rate: 250 Kbps
Antennas Integral – 2 dBi omnidirectional monopole
Integral – 4 dBi omnidirectional monopole
Remote – 8 dBi omnidirectional monopole with up to 20 m cable and lightning surge arrester.
Remote – 14 dBi directional parabolic with up to 20 m cable and lightning surge arrester.
Signal Range Nominal 305 m (1,000 feet) between Field Transmitter and Infrastructure Unit (Multinode) or
Gateway Unit when using 2 dBi Integral antenna with a clear line of sight.*
Two XYR 6000 transmitters both having TX Power set to 16 dBm with a clear line of site nominal
signal range is 150 m (490ft.)
Routing vs Non- Unit can be set as a Field Routing or non-Field Routing device; the number of routing devices is set
Routing by the system manager.
Using the device as a routing device will impact battery life, the more messages routed through a
device, the greater the impact on battery life.
* Actual range will vary depending on antennas, cables and site topography.
34-XY-03-24
Page 4
Remote Antennas
Performance Under Rated Conditions* - Models STGW944 & 94L (0 to 500 psi/35 bar)
Parameter Description
Upper Range Limit psi 500
bar 35
Zero Elevation and Suppression No limit except minimum span from absolute 0 (zero) to +100% URL.
Specifications valid over this range.
Accuracy (Reference – Includes ±0.0625% of calibrated span or upper range value (URV), whichever is greater,
combined effects of linearity, terminal based. For URV below reference point (20 psi), accuracy equals:
hysteresis, and repeatability)
20 psi 1.4 bar
0.0125 0.05
or 0.0125 0.05 in % of span
span/ psi span/ bar
Zero Temperature Effect per 28°C ±0.15% of span. For URV below reference point (50 psi), effect equals:
(50°F)
50 psi 3.5 bar
0.15
span/ psi or 0.15 span/ bar in % of span
Combined Zero and Span ±0.225% of span. For URV below reference point (50 psi), effect equals:
Temperature Effect per 28°C
50 psi 3.5 bar
(50°F) 0.075 0.15
or 0.075 0.15 in % of span
span/ psi span/ bar
Stability ±0.015% of URL per year
* Performance specifications are based on reference conditions of 25°C (77°F), 10 to 55% RH, and 316L Stainless Steel barrier diaphragm.
Performance Under Rated Conditions* - Models STGW974 & 97L (0 to 3,000 psi/210 bar)
Parameter Description
Upper Range Limit psi 3,000
bar 210
Minimum Span psi 300
bar 21
Zero Elevation and Suppression No limit except minimum span from absolute 0 (zero) to +100% URL.
Specifications valid over this range.
Accuracy (Reference – Includes ±0.075% of calibrated span or upper range value (URV), whichever is greater,
combined effects of linearity, terminal based. For URV below reference point (750 psi), accuracy equals:
hysteresis, and repeatability)
750 psi 52 bar
• 0.025 0.05
or 0.025 0.05 in % of span
span/ psi span/ bar
Zero Temperature Effect per 28°C ±0.20% of span. For URV below reference point (500 psi), effect equals:
(50°F)
500 psi 35 bar
0.20
span/ psi or 0.20 span/ bar in % of span
Combined Zero and Span ±0.30% of span. For URV below reference point (500 psi), effect equals:
Temperature Effect per 28°C
(50°F)
500 psi 35 bar
0.10 0.20
or 0.10 0.20 in % of span
span/ psi span/ bar
Stability ±0.03% of URL per year
* Performance specifications are based on reference conditions of 25°C (77°F), 10 to 55% RH, and 316L Stainless Steel barrier diaphragm.
34-XY-03-24
Page 6
NOTE: Pressure transmitters that are part of safety equipment for the protection of piping (systems) or vessel(s) from
exceeding allowable pressure limits, (equipment with safety functions in accordance with Pressure Equipment Directive
97/23/EC article 1, 2.1.3), require separate examination.
Units can withstand overpressure of 1.5X MAWP without damage.
Mounting
Figure 4—Examples of typical mounting positions for in-line models STGW94L, STGW97L, STGW98L, and
STGW99L. Note that a mounting bracket is not required for in-line models.
millimeters
Reference Dimensions: inches
Figure 5—Typical mounting dimensions for dual-head models STGW944 and STGW974 for reference
34-XY-03-24
Page 9
millimeters
Reference Dimensions: inches
Figure 6—Typical mounting dimensions for in-line models STGW94L, STGW97L, STGW98L,
and STGW99L for reference
34-XY-03-24
Page 10
In Eastern Europe:
Honeywell Praha,
s.r.o. Budejovicka 1
140 21 Prague 4,
Czech Republic
In Asia:
Honeywell Asia Pacific Inc.
Honeywell Building,
17 Changi Business Park Central 1
Singapore 486073
Republic of Singapore
In the Pacific:
Honeywell Pty Ltd.
5 Thomas Holt Drive
North Ryde NSW Australia 2113
(61 2) 9353 7000
In Japan:
Honeywell K.K.
14-6 Shibaura 1-chrome
Minato-ku, Tokyo, Japan 105-0023
Specifications are subject to change without notice.
Or, visit Honeywell on the World
Wide Web at:
www.honeywell.com/ps
34-XY-03-24
Page 11
Model Selection Guides are subject to change and are inserted into the specifications as guidance only.
Prior to specifying or ordering a model check for the latest revision Model Selection Guides which are published at:
http://hpsweb.honeywell.com/Cultures/en-US/Products/Instrumentation/ProductModelSelectionGuides/default.htm
34-XY-16U-34
Issue 15
Page 1 of 4
Instructions
Select the desired Key Number. The arrow to the right marks the selection available.
Make one selection from each table, I and II, using the column below the proper arrow.
Select as many Table III options as desired (if no options or approvals are desired, specify 9X).
A () denotes unrestricted availability. A letter denotes restricted availability.
Restrictions follow Table V.
TABLE II
No Selection 00000
1
Carbon Steel heads are zinc-plated and not recommended for water service due to hydrogen migration. For that service, use
316 stainless steel Wetted Process Heads.
2
Vent/Drains are sealed with Teflon® 9 or PTFE 6
Supplied as indicated or as Grade CW12MW, the casting equivalent of Hastelloy® C-276
3
Hastelloy® C-276 or UNS N10276 7
Supplied as indicated or as Grade M30C, the casting equivalent of Monel 400®
4
Monel 400® or UNS N04400 9
Teflon® or PTFE
5 10
Supplied as 316 SS or as Grade CF8M, Monel 400® or UNS N04400 or UNS N04405
the casting equivalent of 316 SS.
13
The standard reference head for the STG9XX is carbon steel (zinc-plated). See Table III for a stainless steel reference (HR) head option.
Note: End vent drain valve standard for STGW9XX.
34-XY-03-24
Page 12
TABLE IV - OPTIONS
Radio Options (Must Choose a Radio Option)
2.4 GHz Frequency Hopping Spread Spectrum (FHSS) XF
b
2.4 GHz Direct Sequence Spread Spectrum (802.15.4 DSSS-FH) XD
ISA 100.11a Compliant (2.4 GHz Direct Sequence Spread Spectrum 802.15.4 DSSS-FH) XS
Power Option (Must Choose Power Option)
Battery Holder Only - No Battery Included 00
Battery Power BA b
24VDC DC
Transmitter Housing & Electronics Options
Custom Calibration and I.D. in Memory CC
Transmitter Configuration and ID in Memory TC
M20 Conduit Thread (1/2" NPT is standard) A1 f
1/2" NPT to 3/4" NPT 316 SS Conduit Adapter A2 g b
5,9
316 SS Electronics Housing - with M20 Conduit Connections SH
5,9 b
316 SS Housing with 1/2" NPT Conduit Connection A3
Stainless Steel Customer Wired-On Tag TG
(4 lines, 28 characters per line, customer supplied information) b
Stainless Steel Customer Wired-On Tag (blank) TB
End Cap Warning Label in Spanish SP
End Cap Warning Label in Portuguese PG b
End Cap Warning Label in Italian TL
End Cap Warning Label in German GE
Meter Body Options
A286 SS (NACE) Bolts and 304 SS (NACE) Nuts for Process Heads CR
316 SS Bolts and 316 SS Nuts for Process Heads SS b
B7M Bolts and Nuts for Process Heads B7
5
316 SS Adapter Flange - 1/2" NPT with CS Bolts S2 c
5
316 SS Adapter Flange - 1/2" NPT with 316 SS Bolts S3 c
5
316 SS Adapter Flange - 1/2" NPT with NACE A286 SS Bolts S4 c
5
316 SS Adapter Flange - 1/2" NPT with B7M Bolts S5 c
® 3, 6
Hastelloy C-276 Adapter Flange - 1/2" NPT with CS Bolts T2 c b
® 3, 6
Hastelloy C-276 Adapter Flange - 1/2" NPT with 316 SS Bolts T3 c
® 4, 7
Monel 400 Adapter Flange - 1/2" NPT with CS Bolts V2 c
® 4, 7
Monel 400 Adapter Flange - 1/2" NPT with 316 SS Bolts V3 c
5
316 SS Blind Adapter Flange with CS Bolts B3
5
316 SS Blind Adapter Flange with 316 SS Bolts B4
5
316 SS Blind Adapter Flange with NACE A286 SS Bolts B5 b
5
316 SS Blind Adapter Flange with B7M Bolts B6
5
316 SS Center Vent Drain and Bushing CV
Side Vent/Drain (End Vent Drain is standard) SV
®8
Viton Process Head Gaskets VT b
Graphite Process Head Gasket GF
®8
Viton Adapter Flange Gaskets VF m
316 SS Reference Head (Carbon Steel Standard) HR
3
Hastelloy® C-276 or UNS N10276 Table IV continued next page
4
Monel 400® or UNS N04400
5
Supplied as 316 SS or as Grade CF8M, the casting equivalent of 316 SS.
6
Supplied as indicated or as Grade CW12MW, the casting equivalent of Hastelloy® C-276
7
Supplied as indicated or as Grade M30C, the casting equivalent of Monel 400®
8
Viton® or Fluorocarbon Elastomer
9
If ordered with Remote Antenna option, Table III Selection M _ _ _ _ or D _ _ _ _, antenna parts are not SS or Marine type cables
34-XY-03-24
Page 13
Approval
Body Approval Type Location or Classification
II 1 GD; Ex ia IIB; T4, Ta ≤ 70°C, Zone 0; IP66
Intrinsically Safe 3U
Ex tD A20 IP66 T90ºC
II 2 GD; Ex d [ia] IIB; T4, Ta ≤ 70°C, Zone 1; IP66
Flameproof 3B
Ex tD A21 IP66 T90ºC
II 3 GD; Ex nA [nL] IIC; T4, Ta ≤ 84°C, Zone 2
Non-Sparking 3Y
Ex tD A22 IP66 T90ºC
ATEX
II 1 GD; Ex ia IIB; T4, Ta ≤ 70°C, Zone 0; IP66
Intrinsically Safe
Ex tD A20 IP66 T90ºC
II 2 GD; Ex d [ia] IIB; T4, Ta ≤ 70°C, Zone 1; IP66
Flameproof 3C*
Ex tD A21 IP66 T90ºC
II 3 GD; Ex nA [nL] IIC; T4, Ta ≤ 84°C, Zone 2
Non-Sparking
Ex tD A22 IP66 T90ºC
Intrinsically Safe Ex ia IIB; T4, Ta ≤ 70°C, Zone 0; IP66
CU
Ex tD A20 IP66 T90ºC
Flameproof Ex d [ia] IIB; T4, Ta ≤ 70°C, Zone 1; IP66 b
CB
Ex tD A21 IP66 T90ºC
Non-Sparking Ex nA [nL] IIC; T4, Ta ≤ 84°C, Zone 2; IP66
IECEx CY
Ex tD A22 IP66 T90ºC
Australia &
New Zealand Intrinsically Safe Ex ia IIB; T4, Ta ≤ 70°C, Zone 0; IP66
Ex tD A20 IP66 T90ºC
Flameproof Ex d [ia] IIB; T4, Ta ≤ 70°C, Zone 1; IP66
C1*
Ex tD A21 IP66 T90ºC
Non-Sparking Ex nA [nL] IIC; T4, Ta ≤ 84°C, Zone 2; IP66
Ex tD A22 IP66 T90ºC
Intrinsically Safe Ex ia IIB; T4, Ta ≤ 70°C, Zone 0; IP66
ZU
Ex tD A20 IP66 T90ºC
Flameproof Ex d [ia] IIB; T4, Ta ≤ 70°C, Zone 1; IP66
ZB
Ex tD A21 IP66 T90ºC
Non-Sparking Ex nA [nL] IIC; T4, Ta ≤ 84°C, Zone 2; IP66
ZY
SAEx Ex tD A22 IP66 T90ºC
South Africa Intrinsically Safe Ex ia IIB; T4, Ta ≤ 70°C, Zone 0; IP66
Ex tD A20 IP66 T90ºC
Flameproof Ex d [ia] IIB; T4, Ta ≤ 70°C, Zone 1; IP66
ZC*
Ex tD A21 IP66 T90ºC
Non-Sparking Ex nA [nL] IIC; T4, Ta ≤ 84°C, Zone 2; IP66
Ex tD A22 IP66 T90ºC
Intrinsically Safe Ex ia IIC; T4, Ta ≤ 85°C, Zone 0; IP 66
INMETRO
Flameproof Ex d IIC; T4, Ta ≤ 85°C, Zone 1; IP 66 6C*
Brazil
Non-Sparking Ex nA IIC; T4, Ta ≤ 85°C, Zone 2; IP 66
* The user must determine the type of protection required for installation of the equipment. The user shall then check
the box [√] adjacent to the type of protection used on the equipment certification nameplate. Once a type of protection
has been checked on the nameplate, subsequently the equipment shall not be reinstalled using any of the other
certification types.
WARNING – Division 2 / Zone 2 apparatus may only be connected to processes classified as non-hazardous or
Division 2 / Zone 2. Connection to hazardous (flammable or ignition capable) Division 1 / Zone 0, or 1 process is
not permitted.
34-XY-03-24
Page 15
TABLE V Availability
Country (Must Choose a Country Code) Country Code
North America, Canada NA00
European Union EU00 b
Japan JP00 r
RESTRICTIONS
Restriction Available Only With Not Available With
Letters Table Selection Table Selection
b Select only one option from this group
c I __G
III _ 00 _ _
d
III _ _ _ 00
e III _ 00 _ _
f IV SH, A3
g IV BA, SH, A1
h I _2_
i IV CR, S4, B5
Select from Table IV
k IV
S2, S3, S4, S5, T2, T3, V2, V3
m IV VT
n IV SH, A3
p V JP00
r IV 9X
Supplemental
Accessories & Kits
Description Part Number
1/2 NPT Socket Plug (ZN Plated CS) 50021832-001
1/2 NPT Certified Conduit Plug (SS) 50021832-002
M20 Certified Conduit Plug (SS) 50000547-001
M20 Conduit Plug (ZN Plated CS) 50000547-002
Surge Diverter* 50018279-090
Lithium Thionyl Chloride Batteries (Qty 2) 50026010-501
Lithium Thionyl Chloride Batteries (Qty 4) 50026010-502
Lithium Thionyl Chloride Batteries (Qty 10) 50026010-503
* Surge Diverter Accessory supplied with Table III, Selections XXX01, XXX03, XXX10
34-XY-03-24
Page 16
Model Selection Guides are subject to change and are inserted into the specifications as guidance only.
Prior to specifying or ordering a model check for the latest revision Model Selection Guides which are published at:
http://hpsweb.honeywell.com/Cultures/en-US/Products/Instrumentation/ProductModelSelectionGuides/default.htm
Section 13
Issue 15
Page 1 of 4
Instructions
Select the desired Key Number. The arrow to the right marks the selection available.
Make one selection from each table, I and II, using the column below the proper arrow.
Select as many Table III options as desired (if no options or approvals are desired, specify 9X).
A () denotes unrestricted availability. A letter denotes restricted availability.
Restrictions follow Table V.
TABLE II
No Selection 00000
Honeywell Field Solutions, 512 Virginia Drive, Fort Washington, Pennsylvania 19034
Printed in U.S.A. © Copyright 2010. Honeywell International Inc.
34-XY-03-24
Page 17
Availability
TABLE IV - OPTIONS Selection
Radio Options (Must choose a Radio Option)
2.4 GHz Frequency Hopping Spread Spectrum (FHSS) XF
b
2.4 GHz Direct Sequence Spread Spectrum (802.15.4 DSSS) XD
ISA 100.11a Compliant (2.4 GHz Direct Sequence Spread Spectrum 802.15.4 DSSS-FH) XS
Power Option (Must choose Power Option)
Battery Holder Only - No Battery Included 00
Battery Power BA b
24VDC DC
Transmitter Housing & Electronics Options
Custom Calibration and I.D. in Memory CC
Transmitter Configuration and ID in Memory TC
M20 Conduit Thread (1/2" NPT is standard) A1 f f
b
1/2" NPT to 3/4" NPT 316 SS Conduit Adapter A2 g g
1,2
316 SS Electronics Housing - with M20 Conduit Connections SH
b
316 SS1,2 Housing with 1/2" NPT Conduit Connection A3
Stainless Steel Customer Wired-On Tag TG
(4 lines, 28 characters per line, customer supplied information) b
Stainless Steel Customer Wired-On Tag (blank) TB
End Cap Warning Label in Spanish SP
End Cap Warning Label in Portuguese PG b
End Cap Warning Label in Italian TL
End Cap Warning Label in German GE
Transmitter Mounting Brackets Options
Mounting Bracket - Carbon Steel MB
Mounting Bracket - 304 SS SB b
Flat Mounting Bracket - Carbon Steel FB
Services/Calibration/Conformance Options
User's Manual Paper Copy UM
Clean Transmitter for Oxygen or Chlorine Service with Certificate 0X h h
Over-Pressure Leak Test with F3392 Certificate TP
Calibration Test Report and Certificate of Conformance (F3399) F1 b
Certificate of Conformance (F3391) F3
Certificate Options
Certificate of Origin (F0195) F5
NACE Certificate (F0198) F7
Warranty Options
Additional Warranty - 1 year W1 b
Additional Warranty - 2 years W2
1
Supplied as 316 SS or as Grade CF8M, the casting equivalent of 316 SS.
2
If ordered with Remote Antenna option, Table III Selection M or D , antenna parts are not SS or Marine type cables
_
34-XY-03-24
Page 18
Approval
Body Approval Type Location or Classification
No hazardous location approvals 9X
Class I, II, III, Div. 1, Groups A,B,C,D,E,F,G;
Intrinsically Safe T4, Ta ≤ 85°C; Type 4X
Class I, AEx ia IIC; T4, Ta ≤ 85°C, Zone 0; IP66
Class I, Div. 1, Groups A,B,C,D;
Cl II, Div. 1,Groups E, F & G;
FM Explosion-proof 1C
Cl III, Div. 1, T4, Ta ≤ 85°C; Type 4X b
Class I, AEx d IIC; T4, Ta ≤ 85°C, Zone 1; IP66
Nonincendive Class I, Div. 2, Groups A,B,C,D; T4,
Ta ≤ 85°C; Type 4X
Non-Sparking Class I, AEx nA IIC; T4, Ta ≤ 85°C, Zone 2; IP66
Nonincendive, CL I, Div 2, Groups A,B,C & D,
Nonincendive
CL II & III, Div 2, Groups F & G, T4 Ta = 85°C 2N
Non-Sparking Class I, Ex/AEx nA IIC; T4, Ta ≤ 85°C, Zone 2; IP66
Class I, Div. 1, Gp A,B,C,D; Class II, Div 1,
Intrinsically Safe Gp E,F,G; Class III, Div 1; T4, Ta ≤ 85°C; Type 4X
Class I, Ex/AEx ia IIC; T4, Ta ≤ 85°C, Zone 0; IP66
CSA
Class I, Div. 1, Groups A,B,C,D;
cus
Class II, Div. 1,Groups E, F & G;
Explosion-proof 2C
Class III, Div. 1, T4, Ta ≤ 85°C; Type 4X
Class I, Ex/AEx d IIC; T4, Ta ≤ 85°C, Zone 1; IP66
Class I, Div. 2, Groups A,B,C,D; T4,
Nonincendive
Ta ≤ 85°C; Type 4X
Non-Sparking Class I, Ex/AEx nA IIC; T4, Ta ≤ 85°C, Zone 2; IP66
II 1 GD; Ex ia IIB; T4, Ta ≤ 70°C, Zone 0; IP66
Intrinsically Safe 3U
Ex tD A20 IP66 T90ºC
II 2 GD; Ex d [ia] IIB; T4, Ta ≤ 70°C, Zone 1; IP66
Flameproof 3B
Ex tD A21 IP66 T90ºC
II 3 GD; Ex nA [nL] IIC; T4, Ta ≤ 84°C, Zone 2
Non-Sparking 3Y
Ex tD A22 IP66 T90ºC
ATEX
II 1 GD; Ex ia IIB; T4, Ta ≤ 70°C, Zone 0; IP66
Intrinsically Safe
Ex tD A20 IP66 T90ºC
II 2 GD; Ex d [ia] IIB; T4, Ta ≤ 70°C, Zone 1; IP66
Flameproof 3C*
Ex tD A21 IP66 T90ºC
II 3 GD; Ex nA [nL] IIC; T4, Ta ≤ 84°C, Zone 2
Non-Sparking
Ex tD A22 IP66 T90ºC b
Ex ia IIB; T4, Ta ≤ 70°C, Zone 0; IP66
Intrinsically Safe CU
Ex tD A20 IP66 T90ºC
Ex d [ia] IIB; T4, Ta ≤ 70°C, Zone 1; IP66
Flameproof CB
Ex tD A21 IP66 T90ºC
Ex nA IIC; T4, Ta ≤ 84°C, Zone 2; IP66
IECEx Non-Sparking CY
Ex tD A22 IP66 T90ºC
Australia &
New Zealand Intrinsically Safe
Ex ia IIB; T4, Ta ≤ 70°C, Zone 0; IP66
Ex tD A20 IP66 T90ºC
Ex d [ia] IIB; T4, Ta ≤ 70°C, Zone 1; IP66
Flameproof C1*
Ex tD A21 IP66 T90ºC
Ex nA [nL] IIC; T4, Ta ≤ 84°C, Zone 2; IP66
Non-Sparking
Ex tD A22 IP66 T90ºC
Intrinsically Safe Ex ia IIB; T4, Ta ≤ 70°C, Zone 0; IP66
ZU
Ex tD A20 IP66 T90ºC
Flameproof Ex d [ia] IIB; T4, Ta ≤ 70°C, Zone 1; IP66
ZB
Ex tD A21 IP66 T90ºC
Non-Sparking Ex nA [nL] IIC; T4, Ta ≤ 84°C, Zone 2; IP66
ZY
SAEx Ex tD A22 IP66 T90ºC
South Africa Intrinsically Safe Ex ia IIB; T4, Ta ≤ 70°C, Zone 0; IP66
Ex tD A20 IP66 T90ºC
Flameproof Ex d [ia] IIB; T4, Ta ≤ 70°C, Zone 1; IP66
ZC*
Ex tD A21 IP66 T90ºC
Non-Sparking Ex nA [nL] IIC; T4, Ta ≤ 84°C, Zone 2; IP66
Ex tD A22 IP66 T90ºC
Intrinsically Safe Ex ia IIC; T4, Ta ≤ 85°C, Zone 0; IP 66
INMETRO
Flameproof Ex d IIC; T4, Ta ≤ 85°C, Zone 1; IP 66 6C*
Brazil
Non-Sparking Ex nA IIC; T4, Ta ≤ 85°C, Zone 2; IP 66
* The user must determine the type of protection required for installation of the equipment. The user shall then check the
box [√] adjacent to the type of protection used on the equipment certification nameplate. Once a type of protection has
been checked on the nameplate, subsequently the equipment shall not be reinstalled using any of the other certification
types.
WARNING – Division 2 / Zone 2 apparatus may only be connected to processes classified as non-hazardous or Division 2 / Zone
2. Connection to hazardous (flammable or ignition capable) Division 1 / Zone 0, or 1 process is not permitted.
34-XY-03-24
Page 19
TABLE V Availability
Country (Must Choose a Country Code) Country Code
North America, Canada NA00
European Union EU00 b
Japan JP00 m m
RESTRICTIONS
Restriction Available Only With Not Available With
Letters Table Selection Table Selection
a Approvals Pending
b Select only one option from this group
d III _ 00 _ _, _ _ _ 00
e III _ 00 _ _
f IV SH, A3
g IV BA, SH, A1
h I _2_
j IV SH, A3
m IV 9X
p V JP00
Supplemental
Accessories & Kits
List
Description Part Number Price
1/2 NPT Socket Plug (ZN Plated CS) 50021832-001 **
1/2 NPT Certified Conduit Plug (SS) 50021832-002 **
M20 Certified Conduit Plug (SS) 50000547-001 **
M20 Conduit Plug (ZN Plated CS) 50000547-002 **
Surge Diverter* 50018279-090 **
Lithium Thionyl Chloride Batteries (Qty 2) 50026010-501 **
Lithium Thionyl Chloride Batteries (Qty 4) 50026010-502 **
Lithium Thionyl Chloride Batteries (Qty 10) 50026010-503 **
* Surge Diverter Accessory supplied with Table III, Selections XXX01, XXX03, XXX10
** Consult Honeywell Order Entry Systems for current parts pricing.
34-XY-03-24
Page 20
OneWireless and XYR are trademarks and Experion is a registered trademark of Honeywell International Inc.