Professional Documents
Culture Documents
2011 BF-3(T)
SERVICE NOTES
Issued by RJA
Table of Contents
Identifying the BF-3(T) .....................................................2 Data Backup and Restore Operations ............................9
Cautionary Notes ..............................................................2 Performing a Factory Reset..............................................9
Specifications .....................................................................3 Updating the System ........................................................9
Location of Controls .........................................................4 Test Mode ...........................................................................9
Exploded View ..................................................................5 Circuit Board (Main, VR, LED, SW, Output B
Disassembly Procedure ....................................................6 Board)................................................................................12
Conversion to the BF-3A ..................................................6 Circuit Diagram (Main, VR, LED, SW, Output B
Parts List .............................................................................7 Board)................................................................................14
Verifying the Version........................................................9
BF-3 BF-3A
Production number Up through H**8560 and after User Data Cannot Be Backed Up
H**8559
Style of component mounting Single-side Double-side The setting for the sleep mode is saved on the Main Board even when the
on the circuit board mounting mounting power has been switched off, but neither verification of its status (ON or OFF)
System version Version 1.00 Version 2.00 or later
nor backing up the setting is possible. When the Main Board has been
replaced, the sleep mode is returned to its default (ON). For more information
After identifying the type of the product being serviced, refer to the about the sleep mode, refer to About Sleep Mode (Owner’s Manual, p. 14).
corresponding Service Notes for information on required parts and test No user data other than the setting for the sleep mode is saved.
methods.
BF-3: SERVICE NOTES (#17058043E0)
BF-3A: SERVICE NOTES 2ND EDITION (#17058043E1)
Part Replacement
This version of Service Notes is for the BF-3A.
When replacing components near the power-supply circuit or a heat-
generating circuit (such as a circuit provided with a heat sink or including a
cement resistor), carry out the procedure according to the instructions with
respect to the part number, direction, and attachment position (mounting so as
to leave an air gap between the component and the circuit board, etc.).
Parts List
A component whose part code is ******** will not be supplied as a service part
because one of the following reasons applies.
• Because it is supplied as an assembled part (under a different part code).
• Because a number of circuit boards are grouped together and supplied as
a single circuit board (under a different part code).
• Because supply is prohibited due to copyright restrictions.
• Because reissuance is restricted.
• Because the part is made to order (at current market price).
• Because it is carried in electronic data on the Roland web site.
• Because it is a package or an accessory irrelevant to the function
maintenance of the main body.
• Because it can be replaced with an article on the market. (battery or etc.)
Circuit Diagram
In the circuit diagram, “NIU” is an abbreviation for “Not in Use,” and
“UnPop” is an abbreviation for “Unpopulated.” They both mean non-mounted
components. The circuit board and circuit board diagram show silk-screened
indications, but no components are mounted.
2
Jun. 2011 BF-3(T)
Specifications
1 kΩ
Dimensions
Recommended Load Impedance 73 (W) x 129 (D) x 59 (H) mm
2-7/8 (W) x 5-1/8 (D) x 2-3/8 (H) inches
10 kΩ or greater
Controls Options
Pedal Switch AC Adaptor PSA-series
MANUAL Knob
RES (resonance) Knob
DEPTH Knob
RATE Knob
MODE Knob
* 0 dBu = 0.775 Vrms
* Printed matters will not be supplied after the end of the production. Then,
Indicator download the electronic file from the Roland web site.
CHECK Indicator (Serves also as tempo and battery check indicator) * In the interest of product improvement, the specifications and/or appearance of
this unit are subject to change without prior notice.
Connectors
GUITAR IN Jack
BASS IN Jack
OUTPUT A (MONO) Jack
OUTPUT B Jack
AC adaptor Jack (DC 9 V)
3
Jun. 2011 BF-3(T)
Location of Controls
fig.panel.eps
16
17
18
4
Jun. 2011 BF-3(T)
Exploded View
fig.bunkaizu.eps
10
1
a
9
b 8
6
c
4 5
5
Jun. 2011 BF-3(T)
Disassembly Procedure
1. Remove No. 6 Bottom Cover, and No. 7 Insulating Sheet.
3. Remove the VR Board (1), and then the OUTPUT B jack (2).
fig.bunkai.eps
BF-3 BF-3A
Part Code Part Name Description Part Code Part Name Description
75D6439001 MAIN BOARD ASSY 5100020562 MAIN SHEET ASSY
******** MAIN BOARD ******** MAIN BOARD
******** VR BOARD ******** VR BOARD
->
******** LED BOARD ******** LED BOARD
******** SW BOARD ******** SW BOARD
75D643O000 OUT JACK ASSY ******** OUTPUT B BOARD
G2167301 INSULATION SPACER -> 5100022073 INSULATING SHEET (for insulating the bottom)
******** INSULATING SHEET -> 5100023214 INSULATING SHEET 36X14X0.5 (for insulating OUTPUT B)
G6017304 OWNER’S MANUAL JAPANESE -> 5100021062 OWNER’S MANUAL JAPANESE
G6017305 OWNER’S MANUAL ENGLISH -> 5100021063 OWNER’S MANUAL ENGLISH
fig.insulating-sheet.eps
6
Jun. 2011 BF-3(T)
Parts List
fig.-part1-e.eps
Note: The parts marked # are new. (initial parts) The description “Q’ty” means a necessary number of the parts per one product.
CASING
5100021031 CASE 1
5100021036 PANEL 1
5100021035 PEDAL 1
5100006632 BOTTOM COVER (22027851R0) 1
CHASSIS
5100008294 PEDAL PLATE (22357304R0) 1
KNOB, BUTTON
04567601 P R-KNOB MF BLK/LCG(22480260R0) 3
22480220 P R-KNOB (INTERNAL) (SS) BF BLK/LCG 1
22480221 P O-KNOB (EXTERNAL) (OUTER) S BLK/LCG 1
SWITCH
13129710R0 SWITCH(PUSH) JM-0404(13129710R0) SW500 (SW Board) 1
PWB ASSY
# 5100020562 MAIN SHEET ASSY 1
* This unit includes the following parts.
******** MAIN BOARD 1
******** VR BOARD 1
******** LED BOARD 1
******** SW BOARD 1
******** OUTPUT B BOARD 1
DIODE
F5029423R0 LED L-3VEGW LED500 on LED Board 1
POTENTIOMETER
5100018911 ROTARY POT(F3229220R0) RD912DF-20-20FWH-B50K-60009A2 VR500 (RES, MANUAL) 1
5100014193 R.POTENTIOMETER (F3279853R0) RD901F-20-15FB-B50K-04 VR503 (MODE) 1
F3279852R0 POTENTIOMETER RD901-20-15FW-B54-006 VR501, VR502 (DEPTH, RATE) 2
WIRING, CABLE
5100021030 WIRING W2(3PIN) 1
5100021029 WIRING W1(7PIN) 1
SCREWS
40010267 SCREW M3X10 BINDING MACHINE FE BZC 2
5100007965 SCREW 3X6(H5029325R0) PAN TAPPING B1 BZC 5
5100007512 THUMB SCREW (H5029820R0) 1
40128923 HEX NUT M7 4
5100003918 JACK NUT M9X12X2 NI RTC(H5039510R0) 4
5100008086 INT TOOTH WASHER 9.5X12.5X0.5 NI RTC(H5039205R0) 4
5100008092 PLAIN WASHER 3X6X0.5 RESIN RTC(H5039708R0) 2
5100003926 PLAIN WASHER 9X13.5X0.5T NI(H5039158R0) 4
5100015893 PLAIN WASHER 9.2X14X1.6 NI (H5039104R0) 1
5100015900 PLAIN WASHER 9.6X14XW11X1.0 AL (22137709R0) 1
7
Jun. 2011 BF-3(T)
MISCELLANEOUS
5100007872 BATTERY CONNECTOR 006P BATTERY SNAP (F3419102R0 1
5100007503 BATTERY CUSHION (22267333R0) 1
5100006633 BOTTOM FOOT (22357305R0) 1
5100006631 CAUTION SEAL PSA (FCC/EMI)(G2537516R2) 1
5100007504 COIL SPRING (22177109R0) 1
5100014487 COMPACT PSA LABEL (22537538R0) 1
# 5100020413 EARTH TERMINAL 2
# 5100023214 INSULATING SHEET 36X14X0.5 1
5100022073 INSULATING SHEET 1
5100007870 INSULOCK TIE YJ-80 V2 (H5319102R0) 2
5100002339 LED SPACER 304 1
5100007505 PEDAL GUIDE BUSH (22157702R0) 1
ACCESSORIES (Standard)
# 5100021062 OWNER’S MANUAL JAPANESE 1
# 5100021063 OWNER’S MANUAL ENGLISH 1
8
Jun. 2011 BF-3(T)
* 6. Battery Operation Check is carried out in the normal mode, and not in the
The setting for the sleep mode is saved on the Main Board even when the Test Mode. 7. Noise Check is carried out in its own mode.
power has been switched off, but neither verification of its status (ON or OFF)
nor backing up the setting is possible. When the Main Board has been
replaced, the sleep mode is returned to its default (ON). For more information Entering the Test Mode
about the sleep mode, refer to About Sleep Mode (Owner’s Manual, p. 14).
No user data other than the setting for the sleep mode is saved. 1. Turn down all controls completely counterclockwise (to MIN or
MOMENTARY).
2. Hold down the pedal and connect the AC adaptor to the DC IN jack.
The CHECK LED lights up and the unit enters the Test Mode.
Performing a Factory Reset * The unit cannot enter the Test Mode unless all controls are turned down to
minimum. If the minimum value is not detected for all volume controls due to a
problem such as a defective volume control, the Test Mode cannot be entered.
This product has no factory-reset feature.
Updating the System * If an error occurred in 1. DSP and CPU Check, depressing the pedal does not
quit the mode. In such cases, disconnect the AC adaptor to switch off the power.
A system update cannot be performed for this product. If an update is * At 5. CODEC (ADC) R-channel Check, depressing the pedal does not quit
required, replace with an updated circuit board. Updates can be accomplished the mode. In this case, either adjust the MODE control to any setting other than
only at the factory. ULTRA and depress the pedal, or disconnect the AC adaptor to switch off the
power.
9
Jun. 2011 BF-3(T)
2. Connect the signal generator to the GUITAR IN jack and input a signal
like the following.
200-Hz rectangular wave at 1 Vp-p
3. Verify that a signal like the following (the same as the input signal) is
output from OUTPUT A and B.
200-Hz rectangular wave at 1 Vp-p
fig.001.eps
6. Disconnect the plug from the GUITAR IN jack and connect it to the BASS
IN jack.
7. Verify that a signal like the following is output from OUTPUT A and B.
400-Hz rectangular wave at 1 Vp-p
fig.003.eps
2. Volume Check
Verify that the MODE control is set to MOMENTARY.
* The volume check can be executed only in this sequence: RES -> MANUAL ->
DEPTH -> RATE -> MODE.
9. Verify that a signal like the following (delta wave) is output from
MANUAL Volume Check OUTPUT A.
fig.004.eps
Slowly turn the MANUAL control from MIN to center, and then to MAX,
and verify that the CHECK LED changes in this sequence: green ->
orange -> green -> orange -> green.
10
Jun. 2011 BF-3(T)
2. Verify that the CHECK LED is lighted up red. 2. Connect the stabilized power supply to the DC IN jack, then insert the
plug into the GUITAR IN jack.
3. Connect the oscilloscope to the OUTPUT A and B jacks.
3. Set the output voltage of the stabilized power supply to 9.0 V.
4. Connect the signal generator to the BASS IN jack and input a signal like
the following. 4. Depress the pedal to make the CHECK LED light up.
1-kHz sine wave at -20 dBm 5. Set the output voltage of the stabilized power supply to 7.5 V.
5. Verify that signals like the following are output from OUTPUT A and B. 6. Verify that the CHECK LED dims.
fig.005.eps
7. Detach the plug from the DC IN jack to disconnect the stabilized power
supply.
9. Depress the pedal several times, and verify that the CHECK LED
repeatedly lights up and goes dark.
10. While the CHECK LED is illuminated, disconnect the plug from the
GUITAR IN jack.
2. Hold down the pedal and connect the AC adaptor to the DC IN jack.
6. Connect the noise meter to the OUTPUT A and B jacks.
3. Verify that the CHECK LED is lighted up orange.
7. Verify that the level of each signal at OUTPUT A and B is at the values
4. Release the pedal.
shown below.
-22.5 to -20.5 dBm (JIS-A) 5. Connect the 47-kΩ dummy plug to the GUITAR IN jack.
-22.5 to -20.5 dBm (DIN-Audio) 6. Connect the amp-equipped monitor speaker to the OUTPUT A and B
jacks.
12. Depress the pedal to make the CHECK LED go dark (bypass state).
13. Verify that each noise level at OUTPUT A and B is at the values shown
below.
-103 dBm or lower (JIS-A) or -100 dBm or lower (DIN-Audio)
15. Switch the pedal on and off and turn the respective controls, and verify
that no abnormal noise occurs.
7. Verify that the level of each signal at OUTPUT A and B is at the values
shown below.
-22.5 to -20.5 dBm (JIS-A)
-22.5 to -20.5 dBm (DIN-Audio)
11
Jun. 2011 BF-3(T)
12
Jun. 2011 BF-3(T)
fig.b-main-2.eps
13
Jun. 2011 BF-3(T)
TP28
MAIN BOARD (1/5)
C56
16V 10uF
AVCC
A+3.3
0.1uF
A+3.3
8
0.1uF
C30
IC3
R110
4
NJM4580M(TE1)
C22
IC2
10
NJM2115V(TE1)
4
AVCC TP121 TP2 AGND
D7 AGND R65
1SS362FV(TPL3) C76 C62 56k
1 2 TP117 TP4 10uF 16V 100uF 6.3V D ( 0.5% )
GUITAR IN R83 TP34 TP80
2SK880-GR(TE85R.F)
22k R81
3
TP93
TP113 TP120 TP8 TP40 TP68 D ( 0.5% ) 10k
R30 AGND R77 D ( 0.5% )
6 UnPop C29 C19
Q17
10k
2
7 C95 0.1uF 0.1uF
8 BROWN W125 3 1800pF D ( 0.5% ) C87 100pF
TP86 AGND AGND TP94
C97 1800pF
5
4
4 R89 R79
3 C44 TP87
C104 UnPop
W126 10k R64 C69 C68 22k
1
0.1uF C91 100pF
R5
2 2
VD
VA
10uF 16V 16V 10uF
1M
YELLOW 56k 1 2 15
D ( 0.5% )
2
D ( 0.5% )
W127 C66 3 LIN LOUT 1
JK500 IN-REFV 10uF 16V D ( 0.5% ) IC2 TP12 3
R10
SCJ614M2NCS3B11G BLACK C65 TP42
10k
A+3.3REF 16V 10uF AVREF IC3
AGND NJM2115V(TE1) NJM4580M(TE1)
CHASSIS AGND 1 16
RIN ROUT
SD-DA 9 8 SD-AD
D+3.3 SDTI SDTO
ORANGE
D9 LRCK
BASS IN 2
UnPop
1
R105 TP75
MCK
BCK
11
12
LRCK
MCLK
VCOM 100 56k
D ( 0.5% )
TP60 TP7 7 BCLK TP9 TP90
150k DEM1 TP82 R76 TP57
2 D ( 0.5% ) 6 10k
3
3 13 DEMO
R96
DGND
VSS
D ( 0.5% )
22k
1 R75 PDN
R60 C89 UnPop
0.1uF
JK501 1k 10k C75
C94 1800pF
TP32
IN-DET D ( 0.5% ) 6 10uF 16V IC4
HTJ-064-14D C108
3
CHASSIS 7 AK4552VTP-E2
1uF R80
5 50V 22k
C37
IC2 C92 100pF
A+3.3REF D ( 0.5% )
NJM2115V(TE1) 6
7
VR-DVREF C31 5
VR BOARD (2/5) DGND 0.1uF AGND AVREF IC3
NJM4580M(TE1)
BLACK
MANUAL
VR500
23
RD912DF-20-20FWH-B50K-60009A2
22
RES
21
13
12
11
VR500
RD912DF-20-20FWH-B50K-60009A2
DEPTH
VR501
RD901F-20-15FW-B50K-006
2
1
VR502
RATE
RD901F-20-15FW-B50K-006
2
Battery 006P
1
3
MODE
2
RD901F-20-15FB-B50K-04
7
6
5
4
3
2
1
1
VR503
CN503
VR-DGREF DVREF
C48
10uF
VR-POWER 1
VR-GND 2
VR1_1 3
VR1_2 4
VR2 5
RED
VR3 6
LED BOARD (3/5) VR4 7
CN2 PVCC
2SC4738-GR(TE85L.F)
L-RED
DGND
1 LED-RED 1
A(RED) 1 2
K 3
2 LED-GND 2
3 LED-GRN 3
R114
A(GRN) LED500
33k
L-GRN CN504 CN3
3
L-3VEGW
Q14 1
TP16
2
W128
R24
TP79
22k
TP29
Q18
2
2SA1832-GR(T5L.F.T) R94
1 LED-RED
TP70 TP39
VBAT TP50 IN-REFV AVREF 22k
AVCC
3
TP96
D12 R46 TP59
Q13
TP102
JK1 220
SS14 2SC4738-GR(TE85L.F) Q19 R97
KM02018ABM1P
2
C110 LED-GRN
D ( 0.5% )
2 3 2
R103 UnPop
R104 UnPop
3
1
R16
R18
2.2k
R7
UnPop
10k
10k
0.1uF
1
2SA1832-GR(T5L.F.T)
TP24
5
47uF 25V
100uF 16V
TP23
4 C96 R45
C109
C51
TP6
UDZS TE-17 11B
150
D ( 0.5% )
UnPop
D ( 0.5% )
C15 UnPop
C26
10uF 16V
0.1uF
C71
UnPop
C40
D13
10uF
R111
C70
16V
C72
C13
10uF
D1
R9
12k
12k
GS1G-M4 16V
C90 DGND
UnPop
UnPop
AGND
PVCC D+1.5
1
Q12 Q10 L2
1 2SC4738-GR(TE85L.F) QS5U27TR(PB FREE) ELL6SH151M FB_1.5
TER2
C36 0.1uF
4
2 5
RC-3(T) COMPACT DIP EARTH TERMINAL 3 2
18
100uF
6.3V
1
C58
Q10
C2
1.5k C52
C84 0.1uF 15 10uF
FB_1.5 R115 12k D ( 0.5% ) FB1 D+3.3
16
2.2k
R6
13 INV1
C107 470pF R100 47k R101 1.5k DTC1 12 R109 56 TP56 DGND
C83 0.1uF 6 PVCC1 11
FB_3.3 TP18 5 FB2 OUT1
R35
7
D ( 0.5% )
R116 Q11 L1
10k DTC2
TP85 15k QS5U27TR(PB FREE) ELL6UH221M FB_3.3
D ( 0.5% ) D ( 0.5% ) TP31 4 8
D ( 0.5% )
D ( 0.5% )
D ( 0.5% )
NON2 PVCC2 9
D ( 0.5% )
D ( 0.5% )
0.1uF
4
R15 2 5
C10
OUT2
100uF 6.3V
19
R74
6.8k
R107
R19
STB Q11
0.1uF
R8
1
10k
10k
C41
C59
D ( 0.5% )
C20
2
3 RT
UDZS TE-17 11B
D ( 0.5% )
R66
CT 10
27k
27k
TP19 PGND
10uF
14
C67
16V
D2
SCP
DGND
R37
17
C82 1000pF R29
TP115
VREF
GND
FIN
C105 R108
C9 1000pF
56
R11 10k
470pF C86
1 C6
20
30
Q3
DTC114TUAT106
DGND DGND DGND
14
Jun. 2011 BF-3(T)
fig.d-main.eps@R
TP108
Q8
2SK879-Y(TE85R.F)
2 1
3
TP44
R52
AVREF
220k
1SS387(TPH3.F) D6
Q9
2SK879-Y(TE85R.F)
2 1
3
AVCC TP77
1SS387(TPH3.F)
D3
R22
56k
R2
1M
TP33
TP103
3
DTC114TUAT106
1 C100
Q1
0.1uF
2
AGND 2SC4116-GR(TE85R.F)
AVCC
DGND
Q6
Q16
TP20 TP58
2SK879-Y(TE85R.F) 1 TP69
C73 JK503
C53 2 1 C54 10uF 16V R63 HTJ-064-14I
220k
WHITE
2
R54
R57
220k
R13 220k
1
R56
UnPop W131
220pF
R47
C88
GRAY
D4
10k
3
JK502
(5/5)
2SC4116-GR(TE85R.F)
R95
22k
AVCC R58 CHASSIS HTJ-064-12DMP
1k DGND
TP65 TP67 TP100 OUT-DET
3
Q7
Q15
R51
16V AVREF
R14 220k
R53
AVREF 3
220k
AVREF I2C-SDA
4
D ( 0.5% )
R55
I2C-SCL
1SS387(TPH3.F)
C49 10uF 5
220pF
C93
I2C-WC
D5
R20 C7 0.1uF
56k 100k
R4 C24 0.1uF CN1
1M C17 0.1uF DGND UnPop
TP47 TP41 TP46 C27 0.1uF C46 10uF
AGND AGND AGND TP10 C33 0.1uF C42 0.1uF For UPDATE
DTC114TUAT106
3
C8 0.1uF C4 0.1uF
TP17 C11 0.1uF C18 0.1uF
AGND
4.7k
4.7k
10k
DGND
9
17
26
34
49
61
82
96
114
122
132
144
36
41
55
72
101
108
141
IC7 DGND DGND
M24512-RMN6TP
R71
R70
R84
3
8 E2 2
VCC E1 1
C23 E0 79 121 DA-MUTE
0.1uF 5 I2C-SDA 80 68
4 SDA 6 I2C-SCL 69
VSS SCL 7 I2C-WC
_WC TP55 102
TP63 103 124
TP11 104 125
TP72 105 126 IN-DET
D+3.3 DVREF TP89 106 127 OUT-DET
DGND 128
R31 TP118 129 LED-GRN
UnPop 84 130 CODEC-PDN
85 131 LED-RED
C50 C14
TP53
TP45
TP78
TP91
TP74
10uF 0.1uF 95 53
94 54
56
DGND 93 57
92 58
R26 0 91 59
R43 0 90 60
R27 0 89 63
R33 0 88
R28 0 87 43
86 44
0.01uF
0.01uF
0.01uF
0.01uF
0.01uF
TP66 45
D+1.5
46
134 47
48
D+3.3 51
C81
C77
C78
C80
C79
C47 C32
10uF 0.1uF 52
133
IC1 IC1
VCC
64
8
22pF ESB16.9344F16D35F
4
3 5 RST-DCDC X1
120
C98 78 INT-SW
DGND IC1 27pF 98 D+3.3
TP109
R25
DGND 99
56k
PVCC TC7W04FK(TE85L/F)
135 22
136 24
RESET TP112 137 21
10k
10k
R92
BD45431G-TR R32
0 DGND 29 TP95
TP21 5 4 81 31 TP114
VDD VOUT 33 TP73
3 1 C85 39 TP61
0.1uF
SUB
C16
75 30 TP76
TP106
DGND
TP122
TP123
TP124
10k
10k
10k
10k
10k
10k
TP97
TP98
DGND 76 2
TP54 77 3
4
119 5
R93
R91
R87
R85
R86
R90
BYPASS-MUTE
6
7
118 8
1 8 11
LRCK 110 ESC:MODE1
MCK 2 7 DGND
111
BCK 3 6 107 20
SD-DA 4 5 19
RA1 112 16
SD-AD 100 113 14
116 13
117 12
TP22 15
A+3.3 A+3.3REF
R44
UnPop
D ( 0.5% )
IC6
TP15 TP13
115
123
100
109
138
GREEN UPD800402GJ-211-UEN-A(ESC)
10
18
27
35
50
62
83
97
37
42
73
R12
W132
10k
R59
0.01uF
C39
W133 1k
100uF
DGND
6.3V
C63
JM-0404#01
10uF 16V
W503 LED-GRN
0.1uF
C35
R17
C74
INT-SW
10k
DGND
SW BOARD (4/5)
AGND AGND
15