ae aster)
Sea ‘Technology &..
Technical-Info
SW...C
8/10/12/14/16/18/20/22
Kaieg sin $0 32024
Catalogue order No,
Calibration balance system AT8-AT9 old Software
1” 2015-09-11 ‘5082028Calibration balance system ATB-AT9 old Software
1.
To calibrate the scale the container must be completely empty. Please see also the capture selt-
cleaning in the user guide.
2.
Go to page machine data, in the operating terminal and set correction scales to 0.00
and factor scales on 1.00.
Please follow these steps strict:
1] Boo]
22 DDD » Dksené |s00%
mp ese
Bats lee
a
1
Change from main menu 1
to main menu 2 by
Pressing button 1"
OOOO
Baa]
DOD » Desend <<
(ride 29..2Du-» a
e . 2
e Soa aeeee Change from main menu 2
sae . to main menu 3 by
Toe Roo athe pressing button ,1".
Gassaiae— h
orere'e'e
2 2015-09-11 ‘s032024Calibration balance system ATB-AT9 old Software
3.
Change from main menu 3
to machine data by
pressing button ¥
Baraoae L
4,
You are now in the menu
machine data.
‘Tum knob ,9*, unti the field
Correction scales" is black
{ap geese marked. Push knob ,9",
and set it by turing knob
*9" to 0,00. Push knob “9”
to confirm it.
Tum knob ,9*, until the field
Factor scales" is black
marked. Push knob ,9",
and set it by turning knob
“9° until you have 1,00.
Push knob "9" to confirm it
By pushing button .8", you
menu.
3 2015-05-11 ‘5032024Calibration balance system ATB-AT9 old Software
4.
It could be the weight information in the main menu does not show 0,00. It is because of a rest qty
in the container or any additional equipment you welded on the container.
Please see following steps to correct it:
B0a.~]
aaa. ders
1.
Change from main menu 1
to main menu 2 by
pressing button ,1*.
overe'e"e
L209 ae
(G00 -0D.), 09.39. | P|
‘ea i pa008, = Ghange from main menu 2
fe etonanae, |e it organs by
sao, LE pressing button ,8*.
Hes EE
SEM master
i
ooje'e"e
® 2015-09-11 ‘s032024Calibration balance system ATB-AT9 old Software
Custoner: aaaaaaaaaa|
Tarset val: 239.ak9/m4|
Density
C.Factor: 3.43 staf
| EM master
3.
Jump by pressina button
wi" and ,4" at the same
time to the parameter
menu.
ee 148cr
OK] 22299... 12"
5100-00 25 Brome 2. O3inn
5.
Now put an exactly known test weight on the top of container, or fil
weight
4
‘You are now in the
parameter menu.
Tum knob 9" unti the field
-Parameter 8" is black
marked. Push knob ,9* and
the first digit begins to
blink; set every digit by
turning knob °9". If you.
push it again it wil jump to
the next digit.
Change this parameter
until the scale is 0.
inder with exactly known
More weight means more calibration accuracy. We prefer a weight of min. 1.500k9.
But take care, to not damage the container!Calibration balance system ATB-AT9 old Software
6
Compare the weight in the display with your real loaded weight.
I
Adjust factor scales, as long as display scales fit to the real weight (is normally not far from 1.00)
Setpoint : actual value = Factor scale
Please see following steps:
DDD . Dus7n4 so0%
PH, 983) BD.» |-10%
Sa"! aaaaa.
1.
‘Change from main menu 1
e asoes.-| foman menu by
- pressing button .1*.
aaa.
e@ Smecr me ees
SP) master
ove'e'ere
aaa. au a
(228-29), 29.30 | Re
com A agaaa, |
2.
Change from main menu 2
tomain menu 3 by
pressing button ,1".
SK, a0900.- | gis
fereasaaaa.. “
=
oo aaa.
Barsoraan a
master
ore'e'e'e
a) 2015-09-11 ‘s032024Calibration balance system ATB-AT9 old Software
-OOVD . Desert
(ROT .BD.) BD. TDinn
som, A 89999,
2b, 2339.
Serta00000..
or aaa.
Bars
MACHINE DATA
set Eb
aevehi) 2
2 18 neless + §8838—
$58
3.
Change from main menu 3
to the menu machine data
by pressing button 4"
4.
You are now in the menu
machine data.
Turn knob ,9* until the field
Factor scales” is black
marked. Push knob 0" and
‘set your factor scale by
‘tumning knob "9" until you
reach your real weight in
the field display scales.
Push knob “9” to confirm.
With pushing button “8" you
will get back to your main
menu.
8
Now the calibration is done and you can remove the weight. Some material will be left in the
container after spreading or any tools are in the storage boxes. This weight will be shown in your
scale. You can compensate this with the factor correction scales.
Please see following steps:
78 2015-05-11 ‘5032024ae aster)
Calibration balance system ATB-AT9 old Software ‘Spreading Technology
BEE Oo,
72 DOD 3% soo
1.
Change from main manu 4
to main menu 2 by
pressing button ,1*.
SK, aaaa0..]
frrewrtanaa@a.!
orere'e'e
Da] 2
DDD . Desend
@ fit) |@ao.oo> } 99-20. 2
yeaa Seeee Change from main menu 2
e@ rag, 20080 ? tomain menu3 by
— | ae sing bution 1".
e rat aaa. Pressing
as Ty
master
orere'e'e
° Sa.-|
HODDD .D.378%
209 TOY 9D. TIsen
aaaaa.
aaaaa..
=} fro mtaaaaa.. t
eC
Hiss i
HGS aster
3.
Change from main menu 3
to the menu machine data
by pressing button ,4”
o*ere'e’e
wo 2015-09-11 ‘s032024Calibration balance system ATB-AT9 old Software
4.
You are now in the menu
MACHINE DATA machine data.
Turn knob ,9* until the field
Correction scales" is black
marked. Push knob ,9" and
tum until you reach your
real weight in the field
display scales. Push it
again to confirm.
Push button “8” to get back
to the main menu.
1 2015-05-11 ‘5032024