Professional Documents
Culture Documents
DTX Specification
DTX Specification
Mechanical Interface
Specification
AMD is providing this Specification and any related information (the "Materials") for your internal
evaluation only. No licenses, express or implied, are granted to you by AMD hereunder. Additionally,
please note that this Specification and the contents therein may be modified or amended at any time at
AMD’s sole discretion.
You may, but are not obligated to, provide AMD with feedback, suggestions, and improvements
regarding the DTX Mechanical Interface Specification and drafts thereof for possible
incorporation by AMD or its designee into future versions of the DTX Mechanical Interface
Specification. Such feedback, suggestions, and improvements provided to AMD shall be referred
to herein as “Feedback.” AMD or its designee shall be free to incorporate any and all Feedback
into the DTX Mechanical Interface Specification, and reserves the right to determine, in its sole
discretion, the contents of the DTX Mechanical Interface Specification. You hereby grants to
AMD, and AMD accepts, a non-exclusive, irrevocable, perpetual, worldwide, transferable, royalty-
free license, with the right to any and all Feedback provided by you to AMD hereunder.
Note that your use of the Materials in any manner indicates your compliance with the following
terms and conditions. If you do not agree to these terms and conditions, do not use the Materials
and/or do not provide Feedback.
Unless otherwise provided in a separate written agreement specifically licensing the Materials and signed by
both parties, the Materials may only be used for internal evaluation only. Notwithstanding the foregoing,
the Materials may not be distributed, modified, or reproduced in whole or in part by any means.
LIMITATION OF LIABILITY: THE MATERIALS ARE PROVIDED "AS IS" WITHOUT ANY
EXPRESS OR IMPLIED WARRANTY OF ANY KIND, INCLUDING BUT NOT LIMITED TO
WARRANTIES OF MERCHANTABILITY, NONINFRINGEMENT, TITLE, FITNESS FOR ANY
PARTICULAR PURPOSE, OR WARRANTIES ARISING FORM CONDUCT, COURSE OF
DEALING, OR USAGE OF TRADE. IN NO EVENT SHALL AMD OR ITS LICENSORS BE
LIABLE FOR ANY DAMAGES WHATSOEVER (INCLUDING, WITHOUT LIMITATION,
DAMAGES FOR LOSS OF PROFITS, BUSINESS INTERRUPTION, OR LOSS OF
INFORMATION) ARISING OUT OF THE USE OF OR INABILITY TO USE THE MATERIALS,
EVEN IF AMD HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. BECAUSE
SOME JURISDICTIONS PROHIBIT THE EXCLUSION OR LIMITATION OF LIABILITY FOR
CONSEQUENTIAL OR INCIDENTAL DAMAGES, THE ABOVE LIMITATION MAY NOT
APPLY TO YOU.
AMD does not assume any responsibility for any errors which may appear in the Materials nor any
responsibility to support or update the Materials. AMD retains the right to modify the Materials at any
time, without notice, and is not obligated to provide such modified Materials to you.
NO SUPPORT OBLIGATION: AMD is not obligated to furnish, support, or make any further
information, software, technical information, know-how, or show-how available to you.
U.S. GOVERNMENT RESTRICTED RIGHTS: The Materials are provided with "RESTRICTED
RIGHTS." Use, duplication, or disclosure by the Government is subject to the restrictions as set
forth in FAR 52.227-14 and DFAR 252.227-7013, et seq., or its successor. Use of the Materials by
the Government constitutes acknowledgement of AMD's proprietary rights in them.
Trademarks
PCI Express is a registered trademark of the PCI-Special Interest Group (PCI-SIG).
Other product names used in this publication are for identification purposes only and may be trademarks of their
respective companies.
42197 Rev. 1.00 February 2007 DTX Mechanical Interface Specification
Contents
Revision History ...............................................................................................................................4
List of Figures
Figure 1. Mechanical Requirements ..................................................................................................6
Figure 2. Keepouts – Primary Side ....................................................................................................7
Figure 3. Keepouts – Secondary Side ................................................................................................7
Figure 4. Chassis I/O Aperture Requirements ...................................................................................8
Figure 5. Chassis I/O Rear Panel Location........................................................................................8
Figure 6. 24-Pin Power Connector Pinout .........................................................................................9
Figure 7. 2x2 Power Connector Pinout..............................................................................................9
List of Tables
Table 1. Keepouts ..............................................................................................................................7
Contents 3
DTX Mechanical Interface Specification 42197 Rev. 1.00 February 2007
Revision History
Date Revision Description
February 2007 1.00 Initial public release.
4 Revision History
42197 Rev. 1.00 February 2007 DTX Mechanical Interface Specification
DTX
Mechanical Interface Specification
The DTX Mechanical Interface Specification describes the requirements for the locations,
dimensions, and keepouts of features/components on the motherboard and for the rear I/O
connector panel. This document also provides the pinouts for the power connectors. This
document is intended for both motherboard designers and chassis builders to assist them in
independently designing compatible products.
Motherboard Requirements
Figure 1 on page 6 shows the following mechanical requirements:
• Overall size
o DTX – 9.60 in x 8.00 in (243.84 mm x 203.20 mm)
o Mini-DTX – 6.70 in x 8.00 in (170.18 mm x 203.20 mm)
• Mounting hole locations
• Rear I/O dimensions and locations
• PCI and/or PCI Express® connector locations
5
DTX Mechanical Interface Specification 42197 Rev. 1.00 February 2007
Keepouts
Figures 2 and 3 on page 7 show the primary and secondary sides of the motherboard respectively.
Table 1, also on page 7, lists the maximum component height by area (denoted by letters A
through E shown in these figures).
6
42197 Rev. 1.00 February 2007 DTX Mechanical Interface Specification
Table 1. Keepouts
Maximum
Area
Component Height
A 2.8 in (71.12 mm)
B 0.60 in (15.24 mm)
Figure 2. Keepouts – Primary Side C 1.38 in (35 mm)
D 0.098 in (2.49 mm)
E 0.010 in (0.254 mm)
7
DTX Mechanical Interface Specification 42197 Rev. 1.00 February 2007
8
42197 Rev. 1.00 February 2007 DTX Mechanical Interface Specification
9
DTX Mechanical Interface Specification 42197 Rev. 1.00 February 2007
References
For additional information, refer to the following documents:
10