Professional Documents
Culture Documents
TT-5166 Programmable Temp and Hum Control System Manual
TT-5166 Programmable Temp and Hum Control System Manual
2014-08-12
1/30
KOMEG Service Hotline:400-886-7870 Email:bella@komegtech.com
3 Monitor screen, when setting mode into the fixed value Figure2-1
2/30
KOMEG Service Hotline:400-886-7870 Email:bella@komegtech.com
to enter.
5 Alarm record, you can view all alarm start time, and the recovery Figure2-1
Figure3-2
3/30
KOMEG Service Hotline:400-886-7870 Email:bella@komegtech.com
performed.
4/30
KOMEG Service Hotline:400-886-7870 Email: bella@komegtech.com
3 According to the left and right arrows to switch into curve. Figure4-1
Figure5-1
Figure5-2
programs, the section number and the total time, shall jump the
a jump out the window of the image has not been closed, calculation
program to the total number of segments of time also does not have
please enter the program cycle changes.) Also can click, refresh the
4 According to the set program part number can choose to run the Figure5-1/Figure5-2
program.
5 According to the left and right arrows to switch such as running, will Figure5-1/Figure5-2
enter the program to monitor the detailed pictures, stop when they
Figure6-1
performed.
change.
5 According to the left and right arrows to switch into curve. Figure6-1
Figure7-1
2 Stop the way, when running a power outage, and then calls, such Figure7-1
began to run, was elected to the hot and will start automatically,
3 Fault recovery, after the failure downtime, artificial after the Figure7-1
window.
Figure8-1
2 Set the timing as constant value runtime timing control, such as Figure8-1
3 Temperature humidity slope for the fixed value runtime, when to Figure8-1
4 Figure8-1
Figure9-1
2 The time when the end time for alarm cancel Figure9-1
4 Fault alarm resume can be used to view the history record, Figure9-1
Figure10-2
3 Sampling time, for the data sampling unit time, the factory is 60 s Figure10-1
each page.
6 Hold the curve part will automatically display, hold down the Figure10-1
8 According to the query, can enter the start time of the query. Figure10-1
Figure11-1
Figure11-2
2 According to the download, select the time period of data can be Figure11-2
3 According to the clear, there will be a clear picture, need to hold Figure11-1
10 s clock can remove all the historical data
Figure12-1
components Content
Figure13-1
5 May have a period of 50, can according to the next page, page Figure13-1
select segment number.
Figure14-1
Figure15-1
Figure16-1
ways of output
2 Fully open output is selected as the runtime, which would have Figure16-1
been output.
3 Output is selected as the barrier, the runtime, which would have Figure16-1
been no output.
4 Output elected according to time, run time, which can output Figure16-1
according to the set time.
5 Time must be greater than the open time. Figure16-1
Figure17-1
Figure18-1
Figure19-1
Figure20-1
1 Time to adjust, when the system display the time difference, can Figure20-1
be set, set after press, determine the date/time adjustment.
2 Appointments can be preset time, when the system time arrives, Figure20-1
can automatically start system. (device has been electrified state)
Figure21-1
Figure22-1
Twenty-three,Tip screen
When the program all the time parameter setting for all O, will come out this picture.
4, Program number segment number greater than the total number of segments, when they start
cues, need to modify the minor cycle parameters.
5, When the controller and the communication machine control panel is not on, you will be
prompted with pictures, need to check whether the communication line behind the good.
When set to ON images of the lock operation, related operation will appear this hint,
When appear to be set in the operating images of the lock is set to OFF, you won't get some
hints.
8, The keypad
2
For the clear key
3
For more multifunction button, you can switch uppercase
and lowercase, symbols, pinyin input.
THE END
If you find mistakes in manual and please send mail to the bella@komegtech.com
2014.08.12