Professional Documents
Culture Documents
2007
DATED.
D
(Sole plate at
" (Typ.)
" (Typ.)
bearing)
1" (Typ.)
anchor rod with heavy
hex nut (All galvanized)
AND
" (Typ.) N L N "THIS MEDIA SHOULD
NOT BE CONSIDERED
A CERTIFIED
SEALED
2"
DOCUMENT."
Q Q
¸
"
¸ Swedge
ELECTRONICALLY
anchor rod
M
" (Min.)
Dimension based on size
H
ELEVATION OF GALVANIZED Top of (Typ.) Burr threads (Typ.)
(Typ.)
of neoprene bearing pad bent cap
STEEL STOPPER PLATE DATE PREPARED
Hex nut (Typ.) Bevel sole plate 9/10/2010
PLAN OF GALVANIZED to match slope of
(Typ.)
(Typ.)
ROUTE STATE
unthreaded
Top of
(Height of
beam (total bevel
STEEL STOPPER PLATE * MO
bent cap shown in column P DISTRICT SHEET NO.
x 1 1/4" x 1/4" below)
HAS BEEN
" (Typ.)
Galvanized steel strap BR *
¸ 9/16" Hole for
bolt)
COUNTY
1/2" anchor rod
with heavy hex nut 1/8" Stainless *
Sole plate steel plate
(all galvanized) JOB NO.
"
1/8" Stainless
(Typ.)
Neoprene CONTRACT ID.
steel plate PTFE
"
PTFE
elastomeric
B
Neoprene Flat surface (see Sec 1080) pad PROJECT NO.
bearing
pad
1/8" Stainless
" " BRIDGE NO.
steel plate
1/8" Stainless Sole plate C BRG 7
1/8" Stainless
steel plate " A "
DESCRIPTION
steel plate
")
G Bond Polytetrafluoroethylene
PTFE, 1/8" (PTFE) to 1/8" stainless steel
stainless steel
"
plate, then to neoprene
(-0 +
" plate and neoprene ¸ Slotted hole
Sole plate elastomeric pad
elastic pad
(Min.)
IF A
¸ Slotted
A hole
C/2 C/2
K
C
E
"
A " (Min.)
(Typ.) 1/8" Stainless
steel pad
DATE
11 Gage or 1/8"
x x Neoprene elastomeric
shim plate (see
Galvanized steel 1/8" Stainless
PART PLAN SHOWING steel plate
PTFE, 1/8" stainless table for number pad (bond to bearing
stopper plate (Typ.) seat with epoxy adhesive)
TRANSPORTATION
steel plate and required)
STOPPER PLATE
(1-888-275-6636)
CAPITOL
65102
neoprene elastomeric
Stopper plates and straps shall be provided to prevent pad
MO
Payment for fabricating and installing the stopper plates
WEST
PART PLAN
CITY,
and straps will be considered completely covered by the
contract unit price for Type N PTFE Bearing.
105
Surface of Surface of
JEFFERSON
The bottom face of the 1/8" stainless steel plate that
COMMISSION
concrete concrete
1-888-ASK-MODOT
is welded to the sole plate shall be lubricated with a
AND
lubricant that is approved by the bearing manufacturer.
HIGHWAYS
1"
1"
2"
"
Top of
(1) USE NOTE H3.29 OR
"
Stopper
4 Equal
conc.
2 " to
spaces
" to
plate "
beam H3.29.1, CHECK WITH
3 "
" to
"
"
STRUCTURAL PROJECT
"
" to
MISSOURI
"
" to
4"
2 "
Anchor rods shall be ASTM F1554 Grade 55 swedged rods and shall
DETAIL FOR 3/4" THRU OPTIONAL DETAIL FOR 1 3/8" extend into the concrete with AASHTO M291 (ASTM A563) Grade A Hex or
2 1/2" ANCHOR RODS THRU 2 1/2" ANCHOR RODS Heavy Hex nuts. Actual manufacturer’s certified mill test reports
(chemical and mechanical) shall be provided. Swedging shall be 1" less
SECTION A-A SWEDGE ANCHOR ROD DETAILS than extension into the concrete.
Structural steel for sole plate shall be ASTM A709 Grade and shall be
coated with a minimum of two coats of inorganic zinc primer (5 mils
minimum). The stainless steel plate shall be protected from any coating. (1)
(*) The required shim plate shall be placed between layers of elastomer TOTAL
and molded together to form an integral unit. BEARINGS
Type N PTFE Bearings shall be in accordance with Sec 716.