SPEAU@ RGN ico sPeCuLReguReeuenTs FOR prop atte SP 1
eal e Rev.
See eee
SPECIAL REQUIREMENTS FOR
“AXNI”
PROJECT : KHDS
OWNER ~~ : M/S BORL
JOB NO. B109
ye
ics cee hy
S180 Tue as job speciation —_KCY__NK
Rev. Date Porpose Prepared Checked Approved
by by byeT ORM ien SPecuLReoUREEMENTSFOR gion. or. te<0 sr-0001
ae eras i ‘Rov.
4.0 GENERAL
‘This specification applicable for WET H2S Application for Carbon Steels,
20 WET H2S RESISTANT MATERIALS.
24 REQUIREMENTFOR CS MATERIAL IN WET H2S SERVICE
244 CarbonStea! (CS) most be ful kiled
242 Carbon Steel (CS) products shall be supplied in he Normalized or Quench
‘and Tenpared condition regarloss of thickness,
24.3 Hardness of Carbon Stee! (CS) products (base metal before PWHT) shall
belimtod below 22HRC (or 237 HE.
2.44 Ncontant shal be Lined below 130
245 — Cccontent shal be Linited below 0.20% w
246 Garton Equiaient CE = C+ Mrs + (Crt MovVVS + (NisCuy18 should
belted to
= Belon 0 42% for thickness below 2
1 Belon 0.45% for thickness above
2.4.7 _Inaddlton to above points, Phosphorus and Sulur content ited as
described in folowing sections dedicated to efferent CS Product forms
24.8 Thermal stress reliving is required for cold worked and cold forged
zones, even f not roquifed by the construction code, Col defermation
above 5% may require recovery annealing o restore proper of stool
22 Plates, welded
1s and other products originated from Plates
Impurty level in carbon sioel products originated trom plates shall be controlled in
‘ofdert0 avoid the acourrence of ite phases curing welcing!
Maximum allowable Phosphors content .02056W
Maximum allowable Sulfur content 0.010%
22:4 Impact Test Proverties
Charpy V-noteh impact testing is required for al pressure retaining components
‘The impact lest value mentioned correspond io the average of absorbed encroy
Requifed for thes sample taken in ansverceorantation and impact ested at
given Temperatre
ITS is spectied (no incleation of MDM), impact tect values shall ot be lees
than those indicted in EN 10028-2 speciication: 34) at O°C.
23 Seamless pipesand seamless Tubes
‘Small & Mecium sze process piping and tubing for heat exchangers shall be of|
Seamless type whenever possibe.
Impurity lol in asamieae oarben steal izes and tubes shal be conte
cider to avoid the cccurrence of brite phases during welding:
Maximum allowable Phosphorus content 0.030%
= Maximum allowable Sulfor content 0.01056pee Jos secmcan0H
eSREORM Mico srecntmcquneewenrsron siorareaasroot
23:1 Impact Test Properties
For CS, i the seamless pipe is used for pressure vessel, the requirements for impact
test must folow those defined fr plates. If tie used for piping.
the requirements of ENT0216-2+A2 specification are applied: minimum energy 27J
aoe.
24 Forging, Casting, Fitting and Accessories
Impurity level in carbon ste! forging, castings and ftings not onginated from plates
{hall be controll in ardar to avoid the oecuttence of bitte phases dun welding
Maximum allowable Phosphorus content 0.025%
= Maximum allowable Sulfur content 0.020%
241 Impact Test Propertos
Fr CS (no indication of MOM), ithe forging is used for prossure vessel, the
requirements forimpact est musi folow those defined fr plates in all ther cases,
the mpaet test value shal not be less than these indicated in EN10022-4,
spectiation: minimum energy 274 at O°C.
For CS the requirements for impact test value must follow those defined in EN 10523-
2 (minimum energy 274 a 0°C for fitings and those defined in ENTO213 (minimum
energy 274 at 20°C for casting
3.4 WELDING/ PWHT! HARDNESS in wet H2S Service
3.44 Fill metal and weld depost shall have difusible hydrogen content
‘typically below SMU1009. Nickel content of filer metal also shall emaie
Below 1% and Manganese content below 1.5%.
3.4.2 Welding Procedure Specification WPS for CS material in wet H2S serve
shall inlude PWHT requrements regardless of onstruction code
Fequiremerts. PWHT temperature shal not be less than 620 °C (1150"F)
{and minimum 83° C (200° F) preheat temperature should be used fra
welding
3.4.3. Hardness shouldbe limited tothe folowing after PWT:
Base Metal 237 HBW (22 HRC)
Weld deposit 200 HBW
= Heat flected Zone (HAZ): 237 HBW (22HRC)
3.4.4 PWHT shal be applied to welded assembles for corosion reasons, and
production welds shal be 100% UT tested. Hardness Verification of
prosction welds is requiredSee Ohi se ae
40 Valves internal nade from carbon steel shall have Harcness limited below 22 HRC
before PHT. Other elements not made from Carbon steal sll comply nah
Secicated secien of NACE MROTOS # applicable.
5.0 In adaltion tothe above requirements, NACE- MR.0103 tobe folowed fo al tems.