Professional Documents
Culture Documents
A8VO
A8VO
A8VO
Data sheet
Series 61 / 63
Sizes 55...200
Nominal pressure 350 bar
Peak pressure 400 bar
for open circuit
Contents Features
Ordering Code / Standard Program 2 – Variable double pump with two axial tapered piston rotary
groups of bent-axis design for hydrostatic drives in open
Technical Data 4
circuits
LA0, LA1 - Individual Power Controller 7
– The flow is proportional to the input speed and to the dis-
EP - Electric Control with Proportional Solenoid 11 placement, and is infinitely variable from qV max to qV min = 0
Unit Dimensions, Size 55 12 – The pump is suitable for direct mounting on the flywheel
case in diesel engines
Unit Dimensions, Size 80 16
– One common suction port for auxiliary pump and both circuits
Unit Dimensions, Size 107 20
– A wide range of control instruments is available for different
Unit Dimensions, Size 140 24
control and regulating functions
Unit Dimensions, Size 200 28
– Individual power controller
Power Take-off Dimensions 32
– Integrated auxiliary pump with pressure-relief valve, optionally
Overview of Attachments 34 with additional pressure-reduction valve
Power Take-off, Auxiliary Pump and Valves 35 – Power take-off for mounting axial piston and gear pumps
Connector for Solenoids 37 – Excellent power to weight ratio
Installation Notes 38 – Long service life
General Notes 40
/40 Bosch Rexroth AG A8VO RE 93010/03.09
Operation mode
02 Double pump (parallel construction), for open circuits O
Size
03 ≈ Displacement Vg max in cm3, per rotary group 55 80 107 140 200
Direction of rotation
06 viewed from shaft end: clockwise R
Seals
08 NBR (nitrile-caoutchouc), shaft seal ring in FKM (fluor-caoutchouc) N
Shaft end
09 Splined shaft, DIN 5480 Z
Power take-off 1) 2)
3 Hub for splined shaft 4)
12 Flange SAE J744 ) 55 80 107 140 200
82-2 (A) 5/8in 9T 16/32DP (A) l l l l l ...01
101-2 (B) 7/8in 13T 16/32DP (B) l l l l l ...02
1in 15T 16/32DP (B-B) l l l l l ...04
127-2 (C) 1 1/4in 14T 12/24DP (C) ❍ l l l l ...07
152-4 (D) 1 1/4in 14T 12/24DP (C) – – – ❍ l ...86
1 3/4in 13T 8/16DP (D) – – – l l ...17
Technical Data
Hydraulic fluid Selection diagram
Before starting project planning, please refer to our data -40° -20° 0° 20° 40° 60° 80° 100°
sheets RE 90220 (mineral oil), RE 90221 (environmentally ac- 1600 1600
1000
ceptable hydraulic fluids) and RE 90223 (HF hydraulic fluids) 600
for detailed information regarding the choice of hydraulic fluids 400
and application conditions. 200
VG 68
VG
VG 32
VG 46
VG 2
10
2
The A8VO variable double pump is not suitable for operation 100
0
with HFA. If HFB, HFC and HFD or environmentally accept- 60
able hydraulic fluids are being used, the limitations regarding
Viscosity n in mm2/s
40 36
technical data and seals mentioned in RE 90221 and RE
νopt.
90223 must be observed. 20
16
When ordering, please indicate the used hydraulic fluid.
10
Operating viscosity range
We recommend that a viscosity (at operating temperature) for 5 5
optimum efficiency and service life purposes of -40° -25° -10° 0° 10° 30° 50° 70° 90° 115°
Temperature t in °C
νopt = optimum operating viscosity 16 to 36 mm2/s
tmin = -40°C Hydraulic fluid temperature range tmax = +115°C
be chosen, taken the tank temperature (open circuits) into
account.
Details regarding the choice of hydraulic fluid
Limits of viscosity range The correct choice of hydraulic fluid requires knowledge of the
operating temperature in relation to the ambient temperature, in
The following values apply in extreme cases:
an open circuit the tank temperature.
νmin = 5 mm2/s
The hydraulic fluid should be chosen so that the operating vis-
short-term (t < 3 min)
cosity in the operating temperature range is within the optimum
at max. perm. temperature of tmax = +115°C.
range (νopt.) - the shaded area of the selection diagram. We
νmax = 1600 mm2/s, recommended that the higher viscosity class be selected in
short-term (t < 3 min) each case.
at cold start (p ≤ 30 bar, n ≤ 1000 rpm, tmin = -40°C).
Example: At an ambient temperature of X°C, an operating tem-
Only for starting up without load. Optimum operating
perature of 60°C is set. In the optimum viscosity range (νopt.,
viscosity must be reached within approx. 15 minutes.
shaded area) this corresponds to the viscosity classes VG 46
Note that the maximum hydraulic fluid temperature of 115°C or VG 68; to be selected: VG 68.
must not be exceeded locally either (e.g. in the bearing area).
Note:
The temperature in the bearing area is – depending on pres-
The case drain temperature, which is affected by pressure and
sure and speed – up to 12 K higher than the average case
speed, is always higher than the tank temperature. At no point
drain temperature.
in the system may the temperature be higher than 115°C.
Special measures are necessary in the temperature range from
If the above conditions cannot be maintained due to extreme
-40°C to -25°C (cold start phase); please contact us.
operating parameters, please contact us.
For detailed information about use at low temperatures, see
RE 90300-03-B.
Filtration
The finer the filtration, the higher the cleanliness level of the hy-
draulic fluid and the longer the service life of the axial piston unit.
To ensure functional reliability of the axial piston unit, the hy-
draulic fluid must have a claenliness level of at least
20/18/15 according to ISO 4406.
At very high hydraulic fluid temperatures (90°C to max. 115°C)
at least cleanliness level
19/17/14 according to ISO 4406 is required.
If the above classes cannot be observed, please contact us.
RE 93010/03.09 A8VO Bosch Rexroth AG /40
Technical Data
Operating pressure range Case drain fluid
Input The case drain chamber is connected to the suction and gear
chambers. A case drain line to the tank is not required. Note the
Pressure on port S special feature of size 200 for flushing fluid.
The minimum permissible inlet pressure depends on the input
speed. The following limit values must not be exceeded or External flushing fluid connection
undercut.
All A8VO variable double pumps in size 200 always require an
pabs min_ _____________________________________ 0.8 bar external flushing fluid connection from the R4 port to the tank, to
The max. pressure pabs max is also dependent on the speed ensure cooling and lubrication of the bearing sets.
(see following diagram).
This line should have an internal diameter ≥ 15 mm.
Minimum permissible inlet pressure at suction port S with Note:
increased speed
The tank level must be higher than the position of the R4 port
In order to avoid damage to the pump (cavitation), a minimum (see page 37).
inlet pressure at the suction port must be assured. The mini-
mum inlet pressure is depends on the speed and the displace-
A3
ment of the variable pump.
1,22 (Speed limit) Minimum inlet pressure pabs in bar R4
1,2 1,5
1,4
R3 R1
Speed n / nmax 1
1,1 1,2
1,1
1,0 1,0
0,9 R4
0,9 0,8
M2
A2
Circuit diagram with R4 port
0,8
0,6 0,7 0,8 0,9 1,0 X1
Displacement Vg / Vg max
Example:
Vg max Vg min M3
Given: Size 80, input speed 2560 rpm X3
results in a minimum inlet pressure of pabs = 1.3 bar at full Temperature range of shaft seal ring
swivel angle (Vg max).
The FKM shaft seal ring is permissible for case drain tempera-
If a free inlet flow can only be achieved at e.g. pabs = 1 bar, the tures of -40°C to +115°C.
displacement must be reduced to 0.88 • Vg max.
Output Input
Pressure on port A1 or A2 Via flexible coupling.
(pressure data according to DIN 24312)
Nominal pressure pN_ ____________________________________ 350 bar
Peak pressure pmax_ ______________________________________ 400 bar
Technical Data
Table of values (theoretical values, without efficiencies and tolerances; values rounded)
Size 55 80 107 140 200
Displacement Vg max cm3 2 x 54.8 2 x 80 2 x 107 2 x 140 2 x 200
Vg min cm3 0 0 0 0 0
Gear ratio i = ninput/nrotary groups 1.0 1.0 1.0 1.0 1.0
Input speed at Vg max 1) nmax 1 rpm 2500 2240 2150 2100 1950
at Vg ≤ Vg max 2) nmax rpm 3000 2750 2450 2450 2250
Flow at nmax and Vg max qv max L/min 2 x 137 2 x 179 2 x 230 2 x 294 2 x 390
Power
at nmax, Vgmax and Dp=350 bar Pmax kW 160 209 268 294 3) 325 3)
Input torque
at Vg max and Dp=350 bar Tmax Nm 611 891 1192 1337 3) 1592 3)
Rotary stiffness (single rotary group) 5)
Vg max to 0,5•Vg max cTW Nm/rad 11213 17985 25565 41408 39505
0,5•Vg max to 0(interpolated) cTW Nm/rad 41442 67666 89381 146677 156876
Moment of inertia for rotary group
with power take-off,
JTW kgm2 0.0161 0.0209 0.0345 0.0581 0.0849
without attachment pump
without power take-off (PTO) JTW kgm2 0.0126 0.0173 0.0288 0.0500 0.0750
Angular acceleration (single rotary group) 5) a rad/s2 25800 21800 17100 7500 11000
Mass approx. m kg 82 90 116 146 180
1) The values shown are valid for absolute pressure (pabs) of 1 bar at suction port S and for operation with mineral fluids with a
specific mass of 0.88kg/L.
2) The values shown are valid for V ≤ V
g g max or for an increase in the inlet pressure pabs at the suction port S (see page 5).
3) Observe max. permissible torque!
4) (...) = Available on request!
5) Caution: Exceeding the permissible limit values may result in a loss of function, a reduction in service life or in the destruction
of the axial piston unit.
Other permissible limit values with respect to speed variation, reduced angular acceleration as a function of the
frequency and the permissible startup angular acceleration (lower than the maximum angular acceleration) can be
found in data sheet RE 90261.
are possible.
Start of control
250 250
Setting range
Setting range
ler, i.e. below the power controller characteristic, the displace- 15
ment is adjusted depending on the pilot pressure. If the set 10
flow or the operating pressure is such that the power controller
characteristic is exceeded, the power controller overrides the 4
stroke limiter and reduces the displacement along the spring
characteristic. 0 0,5 1,0
Vg min Displacement Vg max
Note: The H1/H2/H3 characteristic curve is influenced by the
design of the power controller!
LA0H2; LA1H2
LA0H1/3; LA1H1/3 Hydraulic stroke limiter and external pilot pressure supply
Hydraulic stroke limiter (negative control) (positive control)
Control range from Vg max to Vg min. Control range from Vg min to Vg max.
With increasing pilot pressure the pump swivels to a smaller With increasing pilot pressure the pump swivels to a larger
displacement. displacement.
Start of control (at Vg max) adjustable from 4 – 15 bar Start of control (at Vg min) adjustable 0 to 15 bar
Please specify start of control in clear text when ordering.
Note: The start of control depends on the power controller
setting. Initial position in depressurized state: Vg max
Please specify start of control in clear text when ordering. To control from Vg max to Vg min a pressure ≥ 30 bar is required.
Initial position in depressurized state: Vg max The required fluid is taken from the high-pressure line or the
external control pressure applied at port Y3 (≥ 30 bar) (pilot
Note for H1: pressure < start of control).
A pressure ≥ 30 bar is necessary for control. The required control Characteristic: LA0/1H2
fluid is taken from the high-pressure line. Pilot pressure increase (Vg min – Vg max) ∆p = approx. 25 bar
When using negative control directional valves, the control
pressure is supplied from the negative control system via the
40
high-pressure line.
35
Pilot pressure pSt in bar
15
When using standard open-center directional valves, this
control must be carried out with the external control pressure 10
supply. 5
0 0,5 1,0
Vg min Displacement Vg max
R3 R1
X1
Y3
M
A1
M1 X1
R2 S M2
A2
M
X1
Vg max Vg min M3
X3
X1
M
A1
M1
R2 S
Circuit diagram module for LA0KH3
Y3
X1
X1
Y3
10/40 Bosch Rexroth AG A8VO RE 93010/03.09
800
Series 20_ ______________________________ RE 95200
Series 21________________________________ RE 95201
600 Series 22_ ______________________________ RE 95202
Series 30_ ______________________________ RE 95203
400 and application software
– Analog amplifier RA_______________________ RE 95230
200
M1
A1
M
Y3
Vgmin Vgmax
Y3
M
A2
M2
R2 S
12/40 Bosch Rexroth AG A8VO RE 93010/03.09
LA0KH1/H3, LA1KH1/H3
Individual power controller with hydraulic coupling and hydraulic stroke limiter (negative control)
View X
225
148.9
18
337 X1
162 X3 X1 M3 X1
108 M3
A3 R3 A3
R3
Y3
305
R1 Y3
210
Y3
1,7
ø381 1)
96
-0.214 )
125 1
ø346
ø407
X
ø361.95 -0.
S
25
A2
34.6
184
S
R2 A1
12
30
°
x
M
30
ø11
5 15° 54.3
°
12
243 83.8 192.3
284
62
23.8
50.8
ø19
106.4
ø75
1) Dimensions according to SAE J617-No. 4, for connection to flywheel case in internal combustion engine.
RE 93010/03.09 A8VO Bosch Rexroth AG 13/40
36
12
M16x2 2)5)
ø42
20
58
Ports
A1, A2 Service line ports (high-pressure series) SAE J518 3/4in
Fixing thread DIN 13 M10x1.5; 17 deep 5)
S Suction port (standard series) SAE J518 3in
Fixing thread DIN 13 M16x2; 21 deep 5)
A3 Service line port (auxiliary pump) DIN 3852 M18x1.5; 12 deep 140 Nm 5)
R1, R3 Air bleed port 6) DIN 3852 M14x1.5; 12 deep 80 Nm 5)
R2 Fluid drain 6) DIN 3852 M14x1.5; 12 deep 80 Nm 5)
M Gauge port for control pressure 6) DIN 3852 M12x1.5; 12 deep 50 Nm 5)
M3 Gauge port for power override 3) 6) DIN 3852 M14x1.5; 12 deep 80 Nm 5)
X1 Pilot pressure port for hydraulic stroke limiter DIN 3852 M14x1.5; 12 deep 80 Nm 5)
X3 Pilot pressure port for power override 3) DIN 3852 M14x1.5; 12 deep 80 Nm 5)
Y3 External control pressure port 4) 7) DIN 3852 M14x1.5; 12 deep 80 Nm 5)
2) Center bore according to DIN 332 (thread according to DIN 13)
3) On the LA0 version, the port has no function
4) Only for versions LA...H2 and LA...H3
5) Please observe the general notes for the max. tightening torques on page 40.
6) Plugged
7) 1x plugged, 1x open
14/40 Bosch Rexroth AG A8VO RE 93010/03.09
LA0H2, LA1H2
Individual power controller with hydraulic stroke limiter and external pilot pressure supply (positive control)
View X
337
X1
X1
X3
M3
Y3
314
Y3
X
Y3
LA0K, LA1K
Individual power controller with hydraulic power coupling
View X
(X3)
337
X3
269
X
S
RE 93010/03.09 A8VO Bosch Rexroth AG 15/40
337 (X3)
View X X1 X1
Y3
X3 X1
Y3
312
Y3 X
S
16/40 Bosch Rexroth AG A8VO RE 93010/03.09
LA0KH1/H3, LA1KH1/H3
Individual power controller with hydraulic coupling and hydraulic stroke limiter (negative control)
View X
225
148.9
18
M3
337 X1
162
X1 X1
108 X3 M3 A3
A3
R3 R3
Y3
Y3 Y3
305
R1
210
1,7
ø409.58 -0.232 1)
ø428.62 1)
S
-0.135
A2
ø456
A1
ø394
M2
25
X M1
34.6
S
191
R2 M M
12
30
x3
M °
0°
ø11
6 15° 54.3
12 83.8 192.3
241
284
61.9
27.8
57.2
ø25
106.4
ø75
1) Dimensions according to SAE J617-No. 3, for connection to flywheel case in internal combustion engine.
RE 93010/03.09 A8VO Bosch Rexroth AG 17/40
36
12
M16x2 2)5)
ø42
20
58
Ports
A1, A2 Service line ports (high-pressure series) SAE J518 1in
Fixing thread DIN 13 M12x1.75; 17 deep 5)
S Suction port (standard series) SAE J518 3in
Fixing thread DIN 13 M16x2; 21 deep 5)
A3 Service line port (auxiliary pump) DIN 3852 M18x1.5; 12 deep 140 Nm 5)
R1, R3 Air bleed port 6) DIN 3852 M14x1.5; 12 deep 80 Nm 5)
R2 Fluid drain 6) DIN 3852 M14x1.5; 12 deep 80 Nm 5)
M Gauge port for control pressure 6) DIN 3852 M12x1.5; 12 deep 50 Nm 5)
M1, M2 Gauge port for high-pressure 6) ISO11926 9/16-18UNF-2B;12 deep 80 Nm 5)
M3 Gauge port for power override 3) 6) DIN 3852 M14x1.5; 12 deep 80 Nm 5)
X1 Pilot pressure port for hydraulic stroke limiter DIN 3852 M14x1.5; 12 deep 80 Nm 5)
X3 Pilot pressure port for power override 3) DIN 3852 M14x1.5; 12 deep 80 Nm 5)
X4 Pilot pressure port for load sensing DIN 3852 M14x1.5;12 deep 80 Nm 5)
Y3 External control pressure port 4) 7) DIN 3852 M14x1.5; 12 deep 80 Nm 5)
2) Center bore according to DIN 332 (thread according to DIN 13)
3) On the LA0 version, the port has no function
4) Only for versions LA...H2 and LA...H3
5) Please observe the general notes for the max. tightening torques on page 40.
6) Plugged
7) 1x plugged, 1x open
18/40 Bosch Rexroth AG A8VO RE 93010/03.09
LA0H2, LA1H2
Individual power controller with hydraulic stroke limiter and external pilot pressure supply (positive control)
337 (X3)
View X
X1
X1
X3 Y3
X1
Y3
312
X
Y3
S
LA0K, LA1K
Individual power controller with hydraulic power coupling
View X (X3)
337
X3
X
269
LA0KH2, LA1KH2
Individual power controller with hydraulic power coupling, hydraulic stroke limiter and external pilot pressure supply
(positive control)
X3 Y3
X1
Y3
312
Y3 X
S
RE 93010/03.09 A8VO Bosch Rexroth AG 19/40
LA0KS, LA1KS
Individual power controller with hydraulic power coupling and load sensing
View X (X3)
337
X4 X4
X3
269
X
X4
S
20/40 Bosch Rexroth AG A8VO RE 93010/03.09
Unit Dimensions, Size 107 Before finalizing your design, please request a
binding installation drawing. Dimensions in mm
LA0KH1/H3, LA1KH1/H3
Individual power controller with hydraulic coupling and hydraulic stroke limiter (negative control)
View X
242
165.9
33
364
X1 M3 X1
174
X3 X1
122 A3
A3 R3 M3 Y3
Y3
Y3
308
232
R1
32*)
ø428.62 1)
7,7**)
ø409.58 -0.2321)
32*)
-0.135
ø456
ø388
S
A2 A1
29
38
X M2 M1
196
M
R2 M
12
30
°
x3
M 15°
0°
ø11
12 60.5
6
172*) 94.5 215.5
269
313
27.8
57.2
ø25
120.7
ø90
*) Center of gravity
**) with auxiliary pump 10.7 cm3 = 4.7 mm
1) Dimensions according to SAE J617-No. 3, for connection to flywheel case in internal combustion engine.
RE 93010/03.09 A8VO Bosch Rexroth AG 21/40
36
12
M16x2 2)5)
ø47
20
58
Ports
A1, A2 Service line ports (high-pressure series) SAE J518 1in
Fixing thread DIN 13 M12x1.75; 17 deep 5)
S Suction port (standard series) SAE J518 3 1/2in
Fixing thread DIN 13 M16x2; 21 deep 5)
A3 Service line port (auxiliary pump) DIN 3852 M18x1.5; 12 deep 140 Nm 5)
R1, R3 Air bleed port 6) DIN 3852 M14x1.5; 12 deep 80 Nm 5)
R2 Fluid drain 6) DIN 3852 M14x1.5; 12 deep 80 Nm 5)
M Gauge port for control pressure 6) DIN 3852 M12x1.5; 12 deep 50 Nm 5)
M1, M2 Gauge ports for high-pressure 6) DIN 3852 M14x1.5; 12 deep 80 Nm 5)
M3 Gauge port for power override 3) 6) DIN 3852 M14x1.5; 12 deep 80 Nm 5)
X1 Pilot pressure port for hydraulic stroke limiter DIN 3852 M14x1.5; 12 deep 80 Nm 5)
X3 Pilot pressure port for power override 3) DIN 3852 M14x1.5; 12 deep 80 Nm 5)
X4 Pilot pressure port for load sensing DIN 3852 M14x1.5; 12 deep 80 Nm 5)
Y3 External control pressure port 4) 7) DIN 3852 M14x1.5; 12 deep 80 Nm 5)
2) Center bore according to DIN 332 (thread according to DIN 13)
3) On the LA0 version, the port has no function
4) Only for versions LA...H2 and LA...H3
5) Please observe the general notes for the max. tightening torques on page 40.
6) Plugged
7) 1x plugged, 1x open
22/40 Bosch Rexroth AG A8VO RE 93010/03.09
Unit Dimensions, Size 107 Before finalizing your design, please request a
binding installation drawing. Dimensions in mm
LA0H2, LA1H2
Individual power controller with hydraulic stroke limiter and external pilot pressure supply (positive control)
Y3 X3 X1 Y3
Y3 314 X
LA0K, LA1K
Individual power controller with hydraulic power coupling
View X (X3)
360
X3
272
LA0KH2, LA1KH2
Individual power controller with hydraulic power coupling, hydraulic stroke limiter and external pilot pressure supply
(positive control)
359 (X3)
View X
X1 X1
X3 X1
Y3
Y3
315
X
Y3
S
RE 93010/03.09 A8VO Bosch Rexroth AG 23/40
Unit Dimensions, Size 107 Before finalizing your design, please request a
binding installation drawing. Dimensions in mm
LA0S, LA1S
Individual power controller with load sensing
View X (X3)
364
X4
X4
X3
254
X
X4
S
LA0KS, LA1KS
Individual power controller with hydraulic power coupling and load sensing
364 (X3)
View X
X3
X4 X4
272
EP2
Electric control with proportional solenoid (positive control)
349
View X
139
X
317
Y3
Y3
Y3
24/40 Bosch Rexroth AG A8VO RE 93010/03.09
Unit Dimensions, Size 140 Before finalizing your design, please request a
binding installation drawing. Dimensions in mm
LA0KH1/H3, LA1KH1/H3
Individual power controller with hydraulic coupling and hydraulic stroke limiter (negative control)
View X
282.4
198.5
47
428 X1 M3 X1
220 X1
165 A3
20 48,7 A3 X3 M3
R3
Y3
Y3
310
R1
236
ø409.58 -0.232 1)
40*)
-0.135
30*)
ø428.621)
S
ø394
ø456
A1
42
A2
32
X M2 M1
209
R2
M M
30
12
° M
x3
ø11
6 15° 67
0°
12
220*) 101 235
328
373
57.2
27.8
ø25
130.2
ø100
*) Center of gravity
1) Dimensions according to SAE J617-No. 3, for connection to flywheel case in internal combustion engine.
RE 93010/03.09 A8VO Bosch Rexroth AG 25/40
36
12
M16x2 2)5)
ø52
20
58
Ports
A1, A2 Service line ports (high-pressure series) SAE J518 1in
Fixing thread DIN 13 M12x1,75; 17 deep 5)
S Suction port (standard series) SAE J518 4in
Fixing thread DIN 13 M16x2; 21 deep 5)
A3 Service line port (auxiliary pump) DIN 3852 M18x1.5; 12 deep 140 Nm 5)
R1, R3 Air bleed port 6) DIN 3852 M18x1.5; 12 deep 140 Nm 5)
R2 Fluid drain 6) DIN 3852 M18x1.5; 12 deep 140 Nm 5)
M Gauge port for control pressure 6) DIN 3852 M12x1.5; 12 deep 50 Nm 5)
M1, M2 Gauge port for high-pressure 6) ISO11926 9/16-18UNF-2B;12 deep 80 Nm 5)
M3 Gauge port for power override 3) 6) DIN 3852 M14x1.5; 12 deep 80 Nm 5)
X1 Pilot pressure port for hydraulic stroke limiter DIN 3852 M14x1.5; 12 deep 80 Nm 5)
X3 Pilot pressure port for power override 3) DIN 3852 M14x1.5; 12 deep 80 Nm 5)
X4 Pilot pressure port for load sensing DIN 3852 M14x1.5;12 deep 80 Nm 5)
Y3 External control pressure port 4) 7) DIN 3852 M14x1.5; 12 deep 80 Nm 5)
2) Center bore according to DIN 332 (thread according to DIN 13)
3) On the LA0 version, the port has no function
4) Only for versions LA...H2 and LA...H3
5) Please observe the general notes for the max. tightening torques on page 40.
6) Plugged
7) 1x plugged, 1x open
26/40 Bosch Rexroth AG A8VO RE 93010/03.09
Unit Dimensions, Size 140 Before finalizing your design, please request a
binding installation drawing. Dimensions in mm
LA0H2, LA1H2
Individual power controller with hydraulic stroke limiter and external pilot pressure supply (positive control)
View X X1 (X3) X1
428
X3 X1 Y3
Y3
Y3
310
X
LA0K, LA1K
Individual power controller with hydraulic power coupling
View X (X3)
428
X3
271
LA0KH2, LA1KH2
Individual power controller with hydraulic power coupling, hydraulic stroke limiter and external pilot pressure supply
(positive control)
X1 X1
View X (X3)
428
X3 X1 Y3
Y3 Y3
317
S
RE 93010/03.09 A8VO Bosch Rexroth AG 27/40
Unit Dimensions, Size 140 Before finalizing your design, please request a
binding installation drawing. Dimensions in mm
LA0S, LA1S
Individual power controller with load sensing
X3
X4
274
S
LA0KS, LA1KS
Individual power controller with hydraulic power coupling and load sensing
View X A3 (X3)
428
X3
X4 X4
273
X4
X
S
EP2
Electric control with proportional solenoid (positive control)
410
View X
146
X
325
Y3
Y3 Y3
28/40 Bosch Rexroth AG A8VO RE 93010/03.09
Unit Dimensions, Size 200 Before finalizing your design, please request a
binding installation drawing. Dimensions in mm
LA0KH1/H3, LA1KH1/H3
Individual power controller with hydraulic coupling and hydraulic stroke limiter (negative control)
View X
264.5
186.5
479 26.5
171 X1 M3 X1
68 X1
61,7**) A3 R3 A3 Y3
X3 M3
M2
M1
Y3 Y3
261
R1
329
25*)
ø511.2 -0.232 1)
ø530.2 1)
S
-0.135
ø480
ø555
A1
47
36
R4
X
239
A2
R4 R2 M M
M
12
x3
30
°
0°
15°
ø111)
6 35*)
10 20 104 146
195*)
372
422
66.7
ø32
31.8
ø125
152.4
hole diam. 11 mm for new projects only (previous types with short code G and hole diam. 14 mm)
RE 93010/03.09 A8VO Bosch Rexroth AG 29/40
36
12
M16x2 2)5)
ø60
20
58
Ports
A1, A2 Service line ports (high-pressure series) SAE J518 1 1/4in
Fixing thread DIN 13 M12x1.75; 19 deep 5)
S Suction port (standard series) SAE J518 5in
Fixing thread DIN 13 M16x2; 23 deep 5)
A3 Service line port (auxiliary pump) DIN 3852 M18x1.5; 12 deep 140 Nm 5)
R1, R3 Air bleed port 6) DIN 3852 M22x1.5; 12 deep 210 Nm 5)
R2 Fluid drain 6) DIN 3852 M22x1.5; 12 deep 210 Nm 5)
R4 Flushing fluid port 6) DIN 3852 M18x1.5; 12 deep 140 Nm 5)
M Gauge port for control pressure 6) DIN 3852 M12x1.5; 12 deep 50 Nm 5)
M1, M2 Gauge port for high-pressure 6) ISO11926 9/16-18UNF-2B;12 deep 80 Nm 5)
M3 Gauge port for power override 3) 6) DIN 3852 M14x1.5; 12 deep 80 Nm 5)
X1 Pilot pressure port for hydraulic stroke limiter DIN 3852 M14x1.5; 12 deep 80 Nm 5)
X3 Pilot pressure port for power override 3) DIN 3852 M14x1.5; 12 deep 80 Nm 5)
X4 Pilot pressure port for load sensing DIN 3852 M14x1.5;12 deep 80 Nm 5)
Y3 External control pressure port 4) 7) DIN 3852 M14x1.5; 12 deep 80 Nm 5)
2) Center bore according to DIN 332 (thread according to DIN 13)
3) On the LA0 version, the port has no function
4) Only for versions LA...H2 and LA...H3
5) Please observe the general notes for the max. tightening torques on page 40.
6) Plugged
7) 1x plugged, 1x open
30/40 Bosch Rexroth AG A8VO RE 93010/03.09
Unit Dimensions, Size 200 Before finalizing your design, please request a
binding installation drawing. Dimensions in mm
LA0H2, LA1H2
Individual power controller with hydraulic stroke limiter and external pilot pressure supply (positive control)
View X X1 (X3) X1
479
Y3
X3
X1
Y3
313
X
Y3
S
LA0KH2, LA1KH2
Individual power controller with hydraulic power coupling, hydraulic stroke limiter and external pilot pressure supply
(positive control)
X1 (X3) X1
479 View X
X3 X1 Y3
Y3
338
X
Y3
S
LA0S, LA1S
Individual power controller with load sensing
X4 (X3) X4
479 View X
X3
X4
292
X
S
RE 93010/03.09 A8VO Bosch Rexroth AG 31/40
Unit Dimensions, Size 200 Before finalizing your design, please request a
binding installation drawing. Dimensions in mm
LA0KS, LA1KS
Individual power controller with hydraulic power coupling and load sensing
(X3)
479 View X
X3
X4 X4 X4
292
S
32/40 Bosch Rexroth AG A8VO RE 93010/03.09
A3 Size A1 A2 A3 A4 A5 2)
ø82.55
200 260 12 37 10.2 M10x1.5;15 deep
K02/F02, K04/F04
A2
A5 Size A1 A2 A4 A5 2)
55 185 13.1 10 M12x1.75;18 deep
80 185 13.1 10 M12x1.75;18 deep
ø101.6
146
45° A2 Size A1 A2 A3 A4 A5 2)
A5
55
80 185 16.1 59.1 3) 13 M16x2
107 197 30.1 – 13 M16x2
181
ø127
140 243 15.1 – 13 M16x2
200 267.5 19.5 – 11 M16x2
3) Illustration as for K01
Note related to the position of the fixing threads:
A4
Standard position is shown. Further positions of the fixing
A1 threads available on request.
(to mounting flange)
Please specify in clear text.
A3 K86/F86, K17/F17
161.6
A5 A2 Size A1 A2 A3 A4 A5 2)
140 248.5 20.6 77.6 14.5 M20x2.5
200 267.5 19.5 76.5 14.5 M20x2.5
ø152.4
161.6
A4
A1
(to mounting flange)
Overview of Attachments
Attachment for 2nd pump
Short A4FO A4VG A10VG A10VO/31 A10VO/53 A11VO
Flange Hub for code Size Size Size Size Size Size External
splined shaft K.../F... (Shaft) (Shaft) (Shaft) (Shaft) (Shaft) (Shaft) gear pump
Power take-off – A8VO55/80
82-2 (A) 5/8in 01 – – – – – – Size F
Sizes 4-22 1)
101-2 (B) 7/8in 02 16, 22, – 18 (S) 28 (S, R) 28 (S, R) – Size N
28 (S) 45 (U, W) Sizes 20-32 1)
Size G
Sizes 38-45 1)
1in 04 – 28 (S) 28,45 (S) – 45 (S, R) 40 (S) –
60 (U, W)
127-2 (C) 1 1/4in 07 – 40, 56, (S) – – 60 (S) 60 (S) 2) –
Power take-off – A8VO107
82-2 (A) 5/8in 01 – – – – – – Size F
Sizes 4-22 1)
101-2 (B) 7/8in 02 16, 22, – 18 (S) 28 (S, R) 28 (S, R) – Size N
28 (S) 45 (U) 45 (U, W) Sizes 20-32 1)
Size G
Sizes 38-45 1)
1in 04 – 28 (S) 28,45 (S) 45 (S, R) 45 (S, R) 40 (S) –
60 (U, W)
127-2 (C) 1 1/4in 07 – 40, 56, 71 (S) – – 60 (S) 60 (S) –
Power take-off – A8VO140
82-2 (A) 5/8in 01 – – – – – – Size F
Sizes 4-22 1)
101-2 (B) 7/8in 02 16, 22, – 18 (S) 28 (S, R) 28 (S, R) – Size N
28 (S) 45 (U) 45 (U, W) Sizes 20-32 1)
Size G
Sizes 38-45 1)
1in 04 – 28 (S) 28,45 (S) 45 (S, R) 45 (S, R) 40 (S) –
60 (U, W)
127-2 (C) 1 1/4in 07 – 40, 56, 71 (S) 63 (S) 71 (S, R) 60 (S) 60(S) –
100 (U) 85 (U)
152-4 (D) 1 1/4in 86 – – – – – 75 (S) –
1 3/4in 17 – 90 (S) – 140 (S) – 95 (S) –
Power take-off – A8VO200
82-2 (A) 5/8in 01 – – – – – – Size F
Sizes 4-22 1)
101-2 (B) 7/8in 02 16, 22, – 18 (S) 28 (S, R) 28 (S, R) – Size N
28 (S) 45 (U) 45 (U, W) Sizes 20-32 1)
Size G
Sizes 38-45 1)
1in 04 – 28 (S) 28,45 (S) 45 (S, R) 45 (S, R) 40 (S) –
60 (U, W)
127-2 (C) 1 1/4in 07 – 40, 56, – 71 (S, R) 60 (S) 60 (S) –
71 (S)
100 (U) 85 (U)
152-4 (D) 1 1/4in 86 – – – – – 75 (S) –
1 3/4in 17 – 90, 125 (S) – 140 (S) – 95, 130 –
(S)
1) Rexroth recommends special gear pump versions. Please contact us.
2) For mounting the A11VO size 60, side threaded ports for A1 and A2 are required. Please contact us.
RE 93010/03.09 A8VO Bosch Rexroth AG 35/40
For technical data, see table of values on page 6. For technical data, see table of values on page 6.
For mounting on PTO: The pressure-relief valve installed to protect the integrated
Axial piston pumps and gear pumps auxiliary pump has a fixed setting of 30 bar.
R3 R1 A3
R3 R1
M2
A2
M
M2
X1 A2
M
Vg max Vg min M3 X1
X3
X1
M
A1
M1
R2 S
36/40 Bosch Rexroth AG A8VO RE 93010/03.09
Y View Y
A3
For technical data, see table of values on page 6. For technical data, see table of values on page 6.
The pressure-relief valve installed to protect the integrated The pressure-relief valve installed to protect the integrated
auxiliary pump has a fixed setting of 30 bar. auxiliary pump has a fixed setting of 30 bar. An electrically
For mounting on PTO: controlled pressure-reduction valve can be used to override the
Axial piston pumps and gear pumps power setting (load-limiting control).
A3 Pressure-reduction valve control voltage:
F..4 24V DC
Recommended frequency >100Hz
For mounting on PTO:
R3 R1 Axial piston pumps and gear pumps
A3
M2
A2
M
R3 R1
X1
M2
A2
M
X1
RE 93010/03.09 A8VO Bosch Rexroth AG 37/40
Mating connector
DEUTSCH DT06-2S-EP04
Rexroth Mat. No. R902601804
consisting of: DT designation
– 1 case _________________________________DT06-2S-EP04
– 1 wedge ________________________________________W2S
– 2 sockets _____________________________ 0462-201-16141
The mating connector is not included in supply.
This can be supplied by Rexroth on request. 36
Ø37
50
68,5
Installation Notes
General
During commissioning and operation, the axial piston unit must be filled with hydraulic fluid and air bled. This is also to be ob-
served following a relatively long standstill as the system may empty via the hydraulic lines.
The case drain chamber is internally connected to the suction chamber. A case drain line to the tank is not required.
Note the special feature of size 200 for flushing fluid. (Port R4)
In all operational states, the suction line must flow into the tank below the minimum fluid level.
The minimum suction pressure at port S must not fall below of 0.8 bar absolute.
Installation position
Shaft horizontal.
Below-tank installation
Below-tank installation is when the pump is fitted below the minimum fluid level in the tank.
S
RE 93010/03.09 A8VO Bosch Rexroth AG 39/40
Notice
40/40 Bosch Rexroth AG A8VO RE 93010/03.09
General Notes
– The A8VO pump is designed to be used in open circuits.
– Project planning, assembly and commissioning of the pump require the involvement of qualified personnel.
– The service line ports and function ports are only designed for mounting hydraulic lines.
– During and shortly after operation, there is a risk of burns on the pump and especially on the solenoids. Take suitable safety
precautions, e.g. wear protective clothing.
– There may be shifts in the characteristic depending on the operating state of the pump (operating pressure, fluid temperature).
– Tightening torques:
- The tightening torques specified in this data sheet are maximum values and must not be exceeded
(maximum values for screw thread).
Manufacturer's instruction for the max. permissible tightening torques of the used armatures must be observed!
- For DIN 13 fixing screws we recommend checking the tightening torque individually according to VDI 2230 Edition 2003.
– The data and information contained herein must be adhered to.
Bosch Rexroth AG © This document, as well as the data, specifications and other information set
Hydraulics forth in it, are the exclusive property of Bosch Rexroth AG. It may not be repro-
Axial Piston Units duced or given to third parties without its consent.
Glockeraustrasse 2 The data specified above only serve to describe the product. No statements
89275 Elchingen, Germany concerning a certain condition or suitability for a certain application can be de-
Phone +49 (0) 73 08 82-0 rived from our information. The information given does not release the user from
the obligation of own judgment and verification. It must be remembered that our
Fax +49 (0) 73 08 72 74
products are subject to a natural process of wear and aging.
info.brm-ak@boschrexroth.de
Subject to change.
www.boschrexroth.com/axial-piston-pumps