Professional Documents
Culture Documents
CODE: 00ZARM455UA1E
DIGITAL MULTIFUNCTIONAL
SYSTEM
AR-M351U/M451U
MODEL AR-M355U/M455U
CONTENTS
Parts marked with “ ” are important for maintaining the safety of the set. Be sure to replace these parts with
specified ones for maintaining the safety and performance of the set.
Cautions on laser
+10 nm At the production line, the output power of the scanner unit
Wave length 785 nm
−15 nm is adjusted to 0.4 MILLIWATT PLUS 8 % and is maintained
North America: constant by the operation of the Automatic Power Control (APC).
Pulse times
35 cpm model: (6.2 µs ± 6.2 ns)/7 mm
45 cpm model: (4.8 µs ± 4.8 ns)/7 mm Caution
Europe: This product contains a low power laser device. To ensure
35 cpm model: (6.2 µs ± 6.2 ns)/7 mm safety do not remove any cover or attempt to gain access
45 cpm model: (4.8 µs ± 4.8 ns)/7 mm to the inside of the product. Refer all servicing to qualified
Output power 0.2 mW - 0.4 mW personnel.
This Digital Equipment is rated Class 1 and complies with 21 CFR 1040.10 and 1040.11 of the LASER KLASSE 1
CDRH standards. This means that the equipment does not produce hazardous laser radiation. For
LUOKAN 1 LASERLAITE
your safety, observe the precautions below.
● Do not remove the cabinet, operation panel or any other covers. KLASS 1 LASERAPPARAT
● The equipment's exterior covers contain several safety interlock switches. Do not bypass any
safety interlock by inserting wedges or other items into switch slots. CAUTION
INVISIBLE LASER RADIATION
WHEN OPEN INTERLOCKS
Caution DEFEATED. AVOID EXPOSURE
Use of controls or adjustments or performance of procedures other than those specified herein may result in TO BEAM.
hazardous radiation exposure.
VORSICHT
UNSICHTBARE
LASERSTRAHLUNG WENN
ABDECKUNG GEÖFFNET UND
SICHERHEITSVERRIEGELUNG
ÜBERBRÜCKT. NICHT DEM
STRAHL AUSSETZEN.
ADVARSEL
USYNLIG LASERSTRÅLNING
VED ÅBNING, NÅR
SIKKERHEDSBRYDERE ER
UDE AF FUNKTION. UNDGÅ
UDSAETTELSE FOR
STRÅLNING.
VAROITUS!
LAITTEEN KÄYTTÄMINEN
MUULLA KUIN TÄSSÄ
KÄYTTÖOHJEESSA
MAINITULLA TAVALLA SAATTAA
ALTISTAA KÄYTTÄJÄN
TURVALLISUUSLUOKAN 1
YLITTÄVÄLLE
NÄKYMÄTTÖMÄLLE
LASERSÄTEILYLLE.
manuals4you.com
CONTENTS
1. System configuration . . . . . . . . . . . . . . . . . . . . . . . . .2-1 4. Job status screen (common to print, copy, fax,
network scan and Internet fax) . . . . . . . . . . . . . . . . . 5-4
A. Basic system . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-1
5. Cross sectional view . . . . . . . . . . . . . . . . . . . . . . . . . 5-5
B. Option lineup . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2-2
A. Scanner unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5
C. List of combination of peripheral devices . . . . . . .2-4
B. Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5
[3] SPECIFICATIONS
6. Switch, Sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6
1. Basic Specification . . . . . . . . . . . . . . . . . . . . . . . . . . .3-1
A. Scanner unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6
A. Base Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-1
B. Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-6
B. Document Feeding Equipment . . . . . . . . . . . . . . .3-2
7. PWB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-7
C. Output Equipment . . . . . . . . . . . . . . . . . . . . . . . . .3-2
A. Scanner unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-7
2. Specific Function . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-2
B. Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-7
A. Printer Function . . . . . . . . . . . . . . . . . . . . . . . . . . .3-2
8. Motor, Clutch, Solenoid . . . . . . . . . . . . . . . . . . . . . . . 5-8
B. Image send function . . . . . . . . . . . . . . . . . . . . . . .3-5
A. Scanner unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-8
C. Copy function . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-7
B. Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-8
3. B/W Scanner Module (DSPF). . . . . . . . . . . . . . . . . . .3-8
[6] UNPACKING AND INSTALLATION
4. Rack for Scanner . . . . . . . . . . . . . . . . . . . . . . . . . . . .3-9
1. Installing procedure flowchart . . . . . . . . . . . . . . . . . . 6-1
[4] CONSUMABLE PARTS
2. Note for installation place . . . . . . . . . . . . . . . . . . . . . 6-2
1. Supply system table . . . . . . . . . . . . . . . . . . . . . . . . . .4-1
3. Unpacking procedure . . . . . . . . . . . . . . . . . . . . . . . . 6-2
A. European Subsidiary/East Europe/Russia/
A. AR-M355U/M455U (North America),
Australia/New Zealand . . . . . . . . . . . . . . . . . . . . .4-1
AR-M351U/M451U (Europe) . . . . . . . . . . . . . . . . 6-2
B. Taiwan (Aurora). . . . . . . . . . . . . . . . . . . . . . . . . . .4-1
B. AR-M351U/M451U (Except for Europe) . . . . . . . 6-2
C. Asia . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-1
4. Remove the locking tape
D. Middle East/Africa/Israel/Philippines . . . . . . . . . . .4-1 (AR-M355U/M455U (North America),
E. Hong Kong . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4-1 AR-M351U/M451U (Europe)) . . . . . . . . . . . . . . . . . . 6-3
4. Transport section/Paper exit reverse section . . . . . .7-33 2. Standard original placement orientations . . . . . . . . 10-1
manuals4you.com
[1] GENERAL
1. Note for servicing
Pictogram
This Service Manual uses some pictographs to assure safe opera-
tion.
Please understand the meanings of pictographs before servicing.
CAUTION: If this CAUTION is ignored, an injury or damage to
property could occur.
Fusing unit
Adjuster
manuals4you.com
Lock Release
Necessary options
• Any one of the stand/MPD & 2000 sheet paper drawer (AR-D28), the stand/3 x 500 sheet paper drawer (AR-D27), or the multi purpose
drawer (AR-MU2)*
• Any one of the upper exit tray extension (AR-TE4), the finisher (AR-FN6), the mail-bin stacker (AR-MS1), or the right upper exit tray
(AR-TE5)
• AR-EF3
• AR-RK2
* To install the AR-MU2, the exclusive-use desk is required.
9. Duplex module
(AR-DU3) 12. Mail-bin stacker
(AR-MS1)
y ou.c om
nu a l s 4
ma
(10) Noise
B
At working less than 6.8dB
At waiting mode less than 5.0dB
∗ Showing noise benchmark in each model as a whole system.
(11) Dimensions
External dimensions 37.9" x 26.2" x 44.4"
(W x D x H) (963 mm x 665 mm x 1127 mm)
(including automatic document feeder)
E Occupied space 37.9" x 26.2" (963 x 665 mm)
D dimensions (Include automatic document feeder)
A
(W x D)
Weight Engine: Approx. 85.8 lb (38.9 kg)
Paper size
Desk: Approx. 72.6 lb (32.9 kg)
Printable area Rack: Approx. 16 lb (7.4 kg)
DSPF: Approx. 46 lb (21 kg)
If a printer driver for Windows or Macintosh is used for printing, the
printable area will be smaller. The actual printable area depends
on the printer driver to be used.
B. Taiwan (Aurora)
No. Item Content Life Model name Remarks
1 Toner Cartridge (Black) Toner CA with IC Chip x 10 350k AR-455ET *Life : A4 size at Area Coverage
(Toner; Net Weight 750g) (35k x 10) 6%
2 Developer (Black) Developer x 10 1,000k AR-455LD
(Developer; Net Weight 500g) (100K x 10)
3 Drum Drum x1 200k AR-455DM
C. Asia
No. Item Content Life Model name Remarks
1 Toner Cartridge (Black) Toner CA with IC Chip x 10 350K AR-455CT *Life: A4 size at Area Coverage
(Toner; Net Weight 750g) (35K x 10) 6%
2 Developer (Black) Developer x 10 1,000K AR-455CD
(Developer; Net Weight 500g) (100K x 10)
3 Drum Drum x1 200K AR-455DR
D. Middle East/Africa/Israel/Philippines
No. Item Content Life Model name Remarks
1 Toner Cartridge (Black) Toner CA with IC Chip x 10 350K AR-455ET *Life : A4 size at Area Coverage
(Toner; Net Weight 750g) (35K x 10) 6%
2 Developer (Black) Developer x 10 1,000k AR-455CD
(Developer; Net Weight 500g) (100K x 10)
3 Drum Drum x1 200k AR-455DR
E. Hong Kong
No. Item Content Life Model name Remarks
1 Toner Cartridge (Black) Toner CA with IC Chip x 10 350K AR-455CT-C *Life : A4 size at Area Coverage
(Toner; Net Weight 750g) (35K x 10) 6%
2 Developer (Black) Developer x 10 1,000K AR-455CD-C
(Developer; Net Weight 500g) (100K x 10)
3 Drum Drum x1 200k AR-455DR-C
F. China
No. Item Content Life Model name Remarks
1 Toner Cartridge (Black) Toner CA with IC Chip x1 35k AR-456ST-C *Life : A4 size at Area Coverage
(Toner; Net Weight 750g) 6%
2 Developer (Black) Developer x1 100k AR-455SD-C
(Developer; Net Weight 500g)
3 Drum Drum x1 200k AR-455DR-C
D. China
No. Item Content Life Model name Remarks
1 200K PM kit Cleaner blade x1 200K AR-451KA *1: Screen grid, charging plate, MC
Drum separation pawl x4 cleaner unit are included.
MC unit *1 x1
Toner receiving seal x1
Side malt F x1
Side malt R x1
Transfer roller x1
Discharger plate x1
Paper dust removing unit x1
DV blade x1
DV side seal F x1
DV side seal R x1
Upper heat roller x1
Fusing separation pawl (Upper) x4
Lower heat roller x1
Fusing separation pawl (Lower) x2
Cleaning roller x1
Bearing x2
2 Staple cartridge Staple cartridge x 3 3000 times x 3 AR-SC1 Cartridge for AR-FN4
Common with cartridge for AR-FN6
3 Staple cartridge Staple cartridge x 3 5000 times x 3 AR-SC2 Common with cartridge for AR-FN7
Note: The other maintenance parts which are not listed above are registered as service parts.
1 2 3 4 5 6 7 8 9 10 1 Alphabet
Indicates the production factory.
1 Number
2 Number
For this model, this digit is 2. Indicates the production year.
2 Alphabet
3/4 Number
Indicates the model conformity code. T for this model. Indicates the production month.
3 Number
5/6 Number
Indicates the end digit of the production year. Indicates the production day.
4 Number or X, Y, Z
7 Hyphen
Indicates the production month.
8 Number
X stands for October, Y November, and Z December.
Indicates the production lot.
5/6 Number
Indicates the production day on the month.
3. Environmental conditions
7 Number or X, Y, Z
Indicates the month of packing. A. Operating conditions
X stands for October, Y November, and Z December.
8/9 Number 30 85%
Indicates the day of the month of packing. 85
10 Alphabet
Humidity (%)
Indicates the production factory. "A" for Nara Plant.
35 60%
B. Toner cartridge
The lot number is of 7 digits, and each digit indicates as follows.
The lot number shall be printed in the position shown in the figure.
1 2 3 4 5 6 7
20
1 Version number (A - sequentially revised)
2 Numeral figure 10 Temperature 35
Indicates the end digit of the production year. (Without dew condensation)
3 Alphabet
Indicates the production factory. (B for SOCC) B. Storage conditions
4 Destination code
5/6 Numeral figures
Indicates the production day.
90
7 Numeral figure or X, Y, Z
Humidity (%)
20
-10 Temperature 40
(Without dew condensation)
Heat seal
Aluminum bag
1 2 3 4 5 6 7 8 9 10 12
11 13
1 2 3 4
5 6
2 3
1 2 3
4 5 6 7 8 9 10 11
1 *1 2 "COMPLETE"
"JOB QUEUE" screen job screen
3 4 5 6 7 8 9 10 11
No. Name Function
1 Job list The displayed jobs in the job list are themselves operation keys. To cancel printing or to give a job the highest print
priority, touch the relevant job key to select the job and execute the desired operation using the keys described in 8
and 9.
This shows the current job and the jobs waiting to be run. The icons to the left of the jobs in the queue show the job
mode. The document filing reprint job icon is highlighted.
Note that the icon does not become highlighted during retransmission of a fax/image transmission job.
Print mode Copy mode
E-MAIL/FTP mode
Scan to e-mail job Scan to FTP job Scan to Sharpdesk job
Fax mode
Fax send job Fax reception job PC-Fax send job
Internet Fax mode
i-Fax send job i-Fax reception job PC-Internet Fax send job
*1: "PAPER EMPTY" in the job status display
When a job status display indicates "PAPER EMPTY", the specified paper size for the job is not loaded in any of the
trays.
In this case, the job will be suspended until the required paper is loaded. Other stored jobs will be printed (if
possible) until the required paper is loaded. (Other jobs will not be printed if the paper runs out during printing.) If
you need to change the paper size because the specified paper size is not available, touch the current job key to
select it and then touch the [DETAIL] key described in 10.
2 Mode select key This switches the job list display between "JOB QUEUE" and "COMPLETE".
"JOB QUEUE": Shows stored jobs and the job in progress.
"COMPLETE": Shows finished jobs.
Files saved using the "FILE" and "QUICK FILE" functions and finished broadcast transmission jobs appear as keys
in the finished job screen.
The "FILE" or "QUICK FILE" job keys in the finished job screen can be touched, followed by the [CALL] key, to call
up a finished job and print or transmit it. A finished broadcast transmission job key can be touched followed by the
[DETAIL] key to check the result of the transmission.
3 [PRINT JOB] key This displays the print job list of print mode (copying, printing, fax reception, Internet fax reception, and self printing).
4 [E-MAIL/FTP] key This displays the transmission status and finished jobs of scan mode (Scan to e-mail, Scan to FTP, and Scan to
SharpDesk) when the network scanner option is installed.
5 [FAX JOB] key This displays the transmission/reception status and finished jobs of fax mode (fax and PC-Fax) when the fax option
is installed.
6 Display switching keys Use to switch the page of the displayed job list.
7 [INTERNET-FAX] key This displays the transmission/reception status and finished jobs of Internet fax mode and PC Internet fax mode
when the network scanner option is installed.
8 [STOP/DELETE] key Use to cancel or delete the current job or delete the stored job. Note that printing of received faxes and received
Internet faxes cannot be canceled or deleted.
9 [PRIORITY] key Touch this key after selecting a stored job in this [JOB QUEUE] list to print the job ahead of the other jobs.
Note that a job in progress cannot be interrupted if it is an interrupt copy job or if it is a list print job.
10 [DETAIL] key This shows detailed information on the selected job. Files saved using the "FILE" and "QUICK FILE" functions and
finished broadcast transmission jobs appear as keys in the finished job screen. A Quick File in the finished job
screen or the [Filing] key can be touched, followed by the [CALL] key, to call up a finished job and print or transmit it.
A finished broadcast transmission job key can be touched followed by the [DETAIL] key to check the result of the
transmission.
11 [CALL] key When this key is touched after selecting a job in the COMPLETE job status screen (a job stored using the FILE or
QUICK FILE keys of the document filing function), the "JOB SETTINGS" menu screen appears to let you resend or
reprint the finished job.
15
14 13 12 11 10 9 8
No. Name No. Name
1 CIS unit 10 Copy lamp base unit
2 Original resist roller 11 No. 1 mirror
3 Original resist front sensor (SPPD) 12 Copy lamp (Xenon)
4 Original set sensor (SPED) 13 Mirror base unit
5 Original take-up sensor 14 No. 3 mirror
6 Original length sensor 1 (SPLS1) 15 No. 2 mirror
7 Original length sensor 2 (SPLS2) 16 Original exit roller
8 CCD/lens unit 17 Original exit sensor
9 Original feed roller
B. Engine
POD1 POD2 POD3
21 22 23 24
20
18
15
19
16
17
26 4
3
2
1
8
6
9
25
5
PPD1
10
11
12 13 PED TUD 7 14
12 9
11
10
B. Engine
5.POD3
4.POD2
2.DSW-L
3.POD1
7.TCS
8.LUD
6.PPD1 10.MAIN SW
1.DSW-F
9.PED
12
7
11 8
10
9
B. Engine
1
4
7 5
11
10
13
9
12
3
4
3
1 2
7
6
B. Engine
13.PSPS 16.CNTFAN
10.CFM2
3.POM 6.VFM2
17.PM
1.DM
15.HDDFAN
14.RRC
12.TRC
2.MM
11.CPFC 7.VFM1
7.VFM1
5.LUM
8.CFM1
4.TM
Finishing device
Main unit Main unit
Start of installation
∗ For installation of an option unit, refer to the Service Manual of the option unit.
4) Remove the locking tape from the right and left sidesof the
tray.
Then, Remove the top of the carton and lower the plastic bag
covering the machine while the machine is still on the carton
base.
5) Remove the packing tape from the paper tray, pull out the
paper tray until it stops and remove it by tilting it upward.
Rear side
Note: The center of gravity of the machine lies in the left side
when viewed from the Back of machine. When lifting the <Parts included>
machine, be careful not to drop it.
Front mounting Rear mounting Screws (M4x6):
plates: 2 pcs. plates: 2 pcs. 4 pcs.
"OFF"
Screw Screw
Rear mounting plate
Rear
2) Attach the adjusters and adjust them. mounting plate
<1> Insert the left adjusters to the stand/paper drawer.
<2> Turn the each adjusters to lower them until they touch the
floor. Desk frame
Caution: Insert the rear mounting plates under the desk frame.
<2> Pull out the upper paper tray of the stand/paper drawer until it
stops and attach the front mounting plates using a supplied
screw for each.
Then, remove the lock of the paper tray and close the tray.
2
2
2 Front
mounting plate
1 2
Screw
<2> Hold the main unit of the printer at the positions shown in the
illustration and put the main unit on the stand/paper drawer
so that the front side and the left side of the main unit are
aligned to those of the stand/paper drawer.
Front side
5) Connect the power supply I/F harness to the PCU PWB of the
main unit of the printer.
<1> Remove the screw that fixes the harness cover of the main
unit of the printer and slide the harness cover up to remove it.
Rear side
Process the harness cover as shown in the illustration.
Screw
Harness cover
<Parts included>
1) Turn off the main switch of the main unit of the printer.
Turn the main switch located on the front side of the printer to
the "OFF" position.
Then remove the power plug from the outlet.
<3> Reattach the power supply I/F harness cover to its original
position and fix it with the removed screw.
At this time, ensure that the power supply I/F harness are
"OFF"
arranged as shown in the illustration.
• Fix the harness securely to the wire saddle.
Harness cover
2
Wire saddle 2
Wire saddle
2
6) Attach the paper guides to the lower tray (large capacity tray)
1 2
and set the size.
Refer to "Setting and adjustment" described later. ∗ Be sure to attach the left adjuster to prevent overturning.
∗ If another peripheral device must be installed, carry out the fol- Caution: The lower tray cannot be pulled out unless the adjuster
lowing step at the end of the installation work. is lowered to the specified position.
7) Adjust the position of the paper guides of the upper paper tray 3) Put the main unit of the printer on the stand/paper drawer.
of the stand/paper drawer.
<1> Pull out the paper tray of the main unit until it stops and then
Refer to "Setting and adjustment" described later.
remove it by lifting both ends of the tray.
8) Carry out the off center adjustment.
Rear side 5) Connect the power supply I/F harness to the PCU PWB of the
main unit of the printer.
<1> Remove the screw that fixes the harness cover of the main
unit of the printer and slide the harness cover up to remove it.
Process the harness cover as shown in the illustration.
Screw
Harness cover
<2> Connect the power supply I/F harness connector (red, 22pin)
Screw Screw to CN11 (red connector) of the PCU PWB of the main unit of
the printer.
Rear mounting plate
Connector
Mounting plate
CN11
Desk frame
Caution: Insert the rear mounting plates under the desk frame.
<2> Pull out the upper paper tray of the stand/paper drawer until it
stops and attach the front mounting plates using a supplied
screw for each.
Then, remove the lock of the paper tray and close the tray.
Remove the locks of the middle tray and the lower tray simi- Connect the connector (white, 4pin) of power supply I/F har-
larly. ness to the I/F connector (white, 4pin) of the main unit.
Remove the M4 screw shown in the illustration, insert the cir-
cle terminal of ground harness, and it fixes again.
Front
mounting plate
Screw
Front mounting
plate Screw
Screw
Power supply
I/F harness
<2> Hold the main unit of the printer at the positions shown in the
illustration and put the main unit on the multi purpose drawer
so that the front side and the left side of the main unit are
Harness cover
aligned to those of the multi purpose drawer.
Front side
Wire saddle
Wire saddle
6) Adjust the position of the paper guides of the upper paper tray
of the stand/paper drawer.
Refer to "Setting and adjustment" described later.
7) Carry out the off center adjustment. Rear side
C. AR-MU2
<Parts included>
Screw
Screw
1) Turn off the main switch of the main unit of the printer.
Turn the main switch located on the front side of the main unit
to the "OFF" position. Tray frame
Then, remove the power plug of the main unit from the outlet.
"OFF"
Front
mounting plate
Screw
<3> Reattach the paper tray of the main unit of the printer.
Screw
Cut out.
4) Remove the multi rear cabinet.
<1> Remove the two screws that secure the multi rear cabinet.
Harness cover
Screw
<2> Connect the connector of the relay harness of the multi pur-
pose drawer to the connector of the PCU PWB of the main
unit of the printer.
CN10 Connector
Multi rear cabinet
Screw
<2> Remove the two screws that secure the Harness protection
sheet.
CN11
Screw
Cam
Rack sheet
Harness cover
Wire saddle Rack mounting hole
Boss
Wire saddle
M4 stepped
screw Reference
Reference
Screw
(M4x8
M4 stepped
screw
"OFF"
Rack
Scanner unit
5) Attach the top cover to the developer cartridge and install the
cartridge to the machine.
SIMULATION 25-2
AUTOMATIC DV ADJUSTMENT. PRESS START.
HUMIDITY AREA: 70.0 - 72.5
TEMPERATURE AREA: 70.0 - 72.5
DEVE REFERENCE: 128
D. Paper setting
1) Pull out the first stage paper feed tray.
Slowly pull out the tray until it stops. Press [START] key. Press [CUSTOM SETTINGS] key, and the
operation is stopped immediately or after 2 min.
SIMULATION 25-2
AUTOMATIC DV ADJUSTMENT. EXECUTING···.
HUMIDITY AREA: 70.0 - 72.5
TEMPERATURE AREA: 70.0 - 72.5
DEVE REFERENCE: 118
15mm
Fixing screw
(M4x8)
13. Key sheet attachment
Attach the key sheet to the specified position on the operation
panel according to the support table below.
2) Insert the handle into the left rack notch diagonally upward as
shown in the figure.
Reference 3) Attach the screw which was removed in procedure 1) to
secure the handle.
Reference
4) Lift the rear edge A of the handle to engage the head with
the rack.
2
2
1 2
When
Unit name Part name 100K 200K 300K 400K 500K 600K 700K 800K Remark
calling
Drum peripheral Drum ✕ ▲ ✕ ▲ ✕ ▲ ✕ ▲ Replace at 200K or 1 year.
Cleaner blade ✕ ▲ ✕ ▲ ✕ ▲ ✕ ▲
Toner reception seal ✕ ▲ ✕ ▲ ✕ ▲ ✕ ▲
Side molt F ✕ ▲ ✕ ▲ ✕ ▲ ✕ ▲
Side molt R ✕ ▲ ✕ ▲ ✕ ▲ ✕ ▲
Transfer roller ✕ ✕ ▲ ✕ ▲ ✕ ▲ ✕ ▲
Discharge plate ✕ ✕ ▲ ✕ ▲ ✕ ▲ ✕ ▲
TR bearing (F/R) ✕ ✕ ✕ ▲ ✕ ✕ ✕ ▲
Transfer roller collar ✕ ✕ ✕ ▲ ✕ ✕ ✕ ▲
After-transfer star ring ✕ ✕ ✕ ✕ ✕ ✕ ✕ ✕
TR gear ✕ ✕ ▲ ✕ ▲ ✕ ▲ ✕ ▲
Drum separation pawl unit ✕ ▲ ✕ ▲ ✕ ▲ ✕ ▲
MC unit ✕ ❍ ▲ ❍ ▲ ❍ ▲ ❍ ▲ Includes the screen grid, the
charging plate, and the MC
cleaner.
❍: Charging plate cleaning by
the MC cleaner
Paper guide ❍ ❍ ❍ ❍ ❍ ❍ ❍ ❍ ❍
Developing Developer ▲ ▲ ▲ ▲ ▲ ▲ ▲ ▲ Supplied when installing
section DV blade ✕ ▲ ✕ ▲ ✕ ▲ ✕ ▲
DSD collar ❍ ❍ ❍ ❍ ❍ ❍ ❍ ❍
DV side seal F ✕ ▲ ✕ ▲ ✕ ▲ ✕ ▲
DV side seal R ✕ ▲ ✕ ▲ ✕ ▲ ✕ ▲
Toner cartridge – – – – – – – – Attached when installing./
750g, user replacement for every
35K.
Fusing section Upper heat roller ✕ ✕ ▲ ✕ ▲ ✕ ▲ ✕ ▲
Lower heat roller ✕ ✕ ▲ ✕ ▲ ✕ ▲ ✕ ▲
Upper separation pawl ❍ ❍ ▲ ❍ ▲ ❍ ▲ ❍ ▲
Lower separation pawl ❍ ❍ ▲ ❍ ▲ ❍ ▲ ❍ ▲
Thermistor ✕ ✕ ✕ ✕ ✕ ✕ ✕ ✕ ✕ Clean and remove paper dust.
Upper heat roller gear ✕ ▲ ✕ ▲ ✕ ▲ ✕ ▲
Paper guides ❍ ❍ ❍ ❍ ❍ ❍ ❍ ❍ ❍
Gears ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩
CL roller ✕ ✕ ▲ ✕ ▲ ✕ ▲ ✕ ▲
CL roller bearing ✕ ✕ ▲ ✕ ▲ ✕ ▲ ✕ ▲
Filters Ozone filter ▲ ▲ ▲ ▲ ▲ ▲ ▲ ▲
Paper feed Pick-up roller ✕ ✕ ✕ ✕ ✕ ✕ ✕ ✕ ✕ Note 1
section Paper feed roller ✕ ✕ ✕ ✕ ✕ ✕ ✕ ✕ ✕ Note 1
Separation roller ✕ ✕ ✕ ✕ ✕ ✕ ✕ ✕ ✕ Note 1
Torque limiter ✕ ✕ ✕ ✕ ✕ ✕ ✕ ✕ ✕ Note 1
Transport section Resist roller ✕ ❍ ❍ ❍ ❍ ❍ ❍ ❍ ❍
Paper exit Transport rollers ✕ ❍ ❍ ❍ ❍ ❍ ❍ ❍ ❍
reverse section Transport paper guides ❍ ❍ ❍ ❍ ❍ ❍ ❍ ❍ ❍
Paper dust remover unit ❍ ❍ ▲ ❍ ▲ ❍ ▲ ❍ ▲
Optical reflection sensor ❍ ❍ ❍ ❍ ❍ ❍ ❍ ❍ ❍ PS roller unit section
Drive section Gears (Specified position) ✕ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩
Belts ✕ ✕ ✕ ✕ ✕ ✕ ✕ ✕ ✕
Image quality ✕ ✕ ✕ ✕ ✕ ✕ ✕ ✕ ✕
Other Sensors ✕ ✕ ✕ ✕ ✕ ✕ ✕ ✕ Cleaning is performed by air
blowing.
Note 1: Replacement reference: Use the counter value of each paper feed port as the replacement reference.
Paper feed roller/Separation pad/Torque limiter section (Include Desk, Multi purpose): 100K or 1 years
When
Unit name Part name 100K 200K 300K 400K 500K 600K 700K 800K Remark
calling
Optical Mirror/Lens/Reflector/Sensors ❍ ❍ ❍ ❍ ❍ ❍ ❍ ❍ ❍
section Table glass/Dust-proof glass/OC ❍ ❍ ❍ ❍ ❍ ❍ ❍ ❍ ❍
White reference glass ❍ ❍ ❍ ❍ ❍ ❍ ❍ ❍ ❍
Rails ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩
Drive belt/Drive wire/Pulley ✕ ✕ ✕ ✕ ✕ ✕ ✕ ✕
DSPF Paper feed Pick-up roller ❍ ❍ ❍ ❍ ❍ ❍ ❍ ❍ ❍ Note 2
section Paper feed roller ❍ ❍ ❍ ❍ ❍ ❍ ❍ ❍ ❍ Note 2
Separation mylar lower ❍ ❍ ❍ ❍ ❍ ❍ ❍ ❍ ❍ Note 2
Separation pad ❍ ❍ ❍ ❍ ❍ ❍ ❍ ❍ ❍ Note 2
Transport section PS roller ❍ ❍ ❍ ❍ ❍ ❍ ❍ ❍ ❍
Exposure section ❍ ❍ ❍ ❍ ❍ ❍ ❍ ❍ ❍
(Dust-proof glass)
Paper exit Paper exit roller ❍ ❍ ❍ ❍ ❍ ❍ ❍ ❍ ❍
section
Other Sensors ❍ ❍ ❍ ❍ ❍ ❍ ❍ ❍ For cleaning, blow air.
Note 2: Replacement reference: Replace by using the SPF counter value as an indication.
Paper feed section pickup roller, paper feed roller, separation pad, separation lower mylar lower:
100K or 1 year
When
Option name Part name 100K 200K 300K 400K 500K 600K 700K 800K Remark
calling
Finisher Transport section Transport rollers ❍ ❍ ❍ ❍ ❍ ❍ ❍ ❍ ❍
De-curler roller (❍)✕ ❍ ❍ ❍ ❍ ❍ ❍ ❍ ❍
Transport paper ✕ ❍ ❍ ❍ ❍ ❍ ❍ ❍ ❍
guides
Drive section Gears ✕ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ (Specified position)
Belts ✕ ✕ ✕ ✕ ✕ ✕ ✕ ✕ ✕
Other Sensors ✕ ✕ ✕ ✕ ✕ ✕ ✕ ✕ ✕
Discharge brush ✕ ✕ ✕ ✕ ✕ ✕ ✕ ✕ ✕
Staple unit Replace unit
at 200K staple.
Staple cartridge User replacement
for every 3000 pcs.
Mail-bin Transport section Transport rollers ✕ ❍ ❍ ❍ ❍ ❍ ❍ ❍ ❍
stacker Transport paper ✕ ❍ ❍ ❍ ❍ ❍ ❍ ❍ ❍
guides
Drive section Gears ✕ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ (Specified position)
Belts ✕ ✕ ✕ ✕ ✕ ✕ ✕ ✕ ✕
Other Sensors ✕ ✕ ✕ ✕ ✕ ✕ ✕ ✕ ✕
Discharge brush ✕ ✕ ✕ ✕ ✕ ✕ ✕ ✕ ✕
Saddle finisher, Transport section Transport rollers ✕ ❍ ❍ ❍ ❍ ❍ ❍ ❍ ❍
punch unit Transport paper ✕ ❍ ❍ ❍ ❍ ❍ ❍ ❍ ❍
guides
Drive section Gears ✕ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ (Specified position)
Belts ✕ ✕ ✕ ✕ ✕ ✕ ✕ ✕ ✕
Other Sensors ✕ ✕ ✕ ✕ ✕ ✕ ✕ ✕ ✕
Discharge brush ✕ ✕ ✕ ✕ ✕ ✕ ✕ ✕ ✕
Staple unit Replace unit at 300K
staple.
Staple cartridge User replacement
for every 5000 pcs.
Punch unit Replace unit at
1000K.
ADU Paper feed Paper feed (❍)✕ (❍)✕ (❍)✕ (❍)✕ (❍)✕ (❍)✕ (❍)✕ (❍)✕ (❍)✕ Note 3
+ Manual feed separation section rollers
Transport section Transport rollers ✕ ❍ ❍ ❍ ❍ ❍ ❍ ❍ ❍
Transport paper ✕ ❍ ❍ ❍ ❍ ❍ ❍ ❍ ❍
guides
Drive section Gears ✕ ✩ ✩ ✩ ✩ ✩ ✩ ✩ ✩ (Specified position)
Belts ✕ ✕ ✕ ✕ ✕ ✕ ✕ ✕ ✕
Other Sensors ✕ ✕ ✕ ✕ ✕ ✕ ✕ ✕ ✕
Note 3: Replacement reference: Use the counter value of each paper feed port as the replacement reference.
Paper feed section pickup roller, paper feed roller, separation pad: 100K or 1 year
1. Process section
A. General
Toner is attached to electrostatic latent images formed by the
laser beams which were radiated to the OPC drum charged by the
main charger, forming toner images.
The toner images formed on the OPC drum are transferred to
paper by the transfer roller.
MAX 8KV
constant current
opc27 m
ctc27 m 13 3
Separation electrode 12
1
-1.8KV 4
-650V
11 10
2 (-620V)
30 9
6
-800V
5
25µA (45ppm)
15
19µA (31/35ppm)
MAX 5KV
16 7
Paper dust cleaner Toner density sensor
8
200M 200M
14 14
Temperature/humidity sensor
-500V
(-470)
9
4
5
6
8
3
CN5
B8B-PH-K-S
CN15 GND2 1
1-84432-4(AMP) 9604S-14F +5VCRU 2
SRA-21T-4L DSW-F 1 1 DSW-F CRUCLK 3
PS-187
RD GND2 2 2 GND2 CRUSDA
MHV RD 4
GND2 3 3 GND2 PSPS\ 5
SRA-21T-3 PS-187 DHVREM 4 4 DHVREM
WH +24V1 6
THV WH MHVREM\ 5 5 MHVREM\ (NC) 7
SRA-21T-4L THV+PWM\ 6 6 THV+PWM\ +24V1 8
PS-187
WH GBPWM\ 7 7 GBPWM\
GB YL HV DHVPWM\ 8 8 DHVPWM\ PCU PWB CN6
SRA-21T-3 9604S-08C
PS-187 THV-PWM\ 9 9 THV-PWM\
RD DSW-F 1
DHV BL DVREM\ 10 10 DVREM\
DSW-F 2
DVPWM\ 11 11 DVPWM\
PS-187 GND2 3
THVREM\ 12 12 THVREM\
BIAS DV GR GND2 4
MHV-T 13 13 MHV-T
DM\ 5
THin 14 14 THin
DM-T 6
DMCLK\ 7
(NC) 8
Signal
Code Name Function/Operation Type Note
name
DM DM OPC drum motor Drives the OPC drum and the transfer section. DC brushless motor
PSPS PSPS Drum separation pawl solenoid Drives the OPC drum separation pawl Solenoid
Screen grid
CTL
CGL
Aluminum
layer OPC drum
The main charger grid is provided with the screen grid. The
OPC drum is charged at a voltage virtually same as the volt- Residual toner removed from the OPC drum surface is trans-
age applied to the screen grid. ported to the recycle toner collection section in the toner car-
2) LED lights are radiated to the OPC drum surface by the laser tridge by the waste toner transport screw.
unit to form latent electrostatic images. 4) All the surface of the OPC drum is discharged by laser beams.
CLT CLT
CGL CGL
layer layer
Aluminum Aluminum
OPC drum
OPC drum After completion of the job, laser beams are radiated onto al
CTL the surface of the OPC drum.
CGL When laser beams are radiated onto the CGL of the OPC
layer drum, positive and negative charges are generated.
Aluminum Positive charges generated in CGL are attracted to the nega-
tive charges on the OPC drum surface. On the other hand,
negative charges are attracted to positive charges in the alu-
When LED lights are radiated to the OPC drum CGL, negative
minum layer of the OPC drum.
and positive charges are generated.
Therefore, positive and negative charges are balanced out on
Positive charges generated in CGL are attracted to the nega-
the OPC drum surface and in the aluminum layer, reducing
tive charges on the OPC drum surface. On the other hand,
positive and negative charged to decrease the surface voltage
negative charges are attracted to the positive charges in the
of the OPC drum.
OPC drum aluminum layer.
Therefore, positive charges and negative charges are bal-
anced out on the OPC drum and in the aluminum layer, reduc-
ing positive and negative charges to decrease the OPC drum
surface voltage.
Electric charges remain at a position where LED lights are not
radiated.
As a result, latent electrostatic images are formed on the OPC
drum surface.
2
8
1
3
7
5
2
b-1
a-8
a-5 a 3) Put down the DV guide handle. Loosen the screw, and remove
a-3 the drum cartridge.
a-1
a-2
a-6
a-4
a-7
a-3
After installing the drum separation pawl unit, push the separation
lever and check to confirm that the separation pawl operates nor-
mally.
a-2. Drum
a-3. DSD collar
1) Remove the drum cartridge.
2) Loosen the screw, and remove the drum boss mounting plate.
3) Remove the drum, and remove the DSD collar.
∗ When removing the drum, place the drum cartridge as shown in
the figure and remove the drum.
0.5mm
(From the blade edge) 0.3mm 0mm
0.1mm 0.1mm Reference
Reference
Put side seal powder (1g) on the moquettes F/R and spread side
seal powder all over the moquettes surfaces.
Side seal powder: UKOG-0309FCZZ
∗ Do not apply powder excessively to the ambient parts.
∗ Be careful not to damage the cleaning blade and the side blade.
∗ When installing the cleaner blade, pull the cleaner shaft fully
toward you.
∗ After installing the cleaner blade, insert the cleaner shaft fully to
the bottom.
a-7. Side molt F
a-8. Side molt R
1) Remove the drum cartridge.
2) Remove the drum and the DSD collar. b-1. Separation solenoid
3) Remove the toner reception seal. 1) Remove the screw, and remove the rear cabinet.
4) Remove the cleaner blade.
5) Remove the side molt F and R.
4) Remove the E-ring and the screw, and remove the separation
solenoid.
[Transfer section]
A. General
In this section, toner images on the OPC drum are transferred to
paper.
4 5
3
6
2
4
1 3
CN15
1-84432-4(AMP) 9604S-14F
SRA-21T-4L DSW-F 1 1 DSW-F
PS-187
RD GND2 2 2 GND2 CN6
MHV RD
GND2 3 3 GND2 9604S-08C
SRA-21T-3 PS-187 DHVREM 4 4 DHVREM DSW-F 1
WH
THV WH MHVREM\ 5 5 MHVREM\ DSW-F 2
SRA-21T-4L THV+PWM\ 6 6 THV+PWM\ GND2 3
PS-187
WH GBPWM\ 7 7 GBPWM\ GND2 4
GB YL HV DHVPWM\ 8 8 DHVPWM\ PCU PWB DM\ 5
SRA-21T-3 PS-187 THV-PWM\ 9 9 THV-PWM\ DM-T 6
RD
DHV BL DVREM\ 10 10 DVREM\ DMCLK\ 7
DVPWM\ 11 11 DVPWM\ (NC) 8
PS-187
THVREM\ 12 12 THVREM\
BIAS DV GR
MHV-T 13 13 MHV-T
THin 14 14 THin
Signal
Code Name Function/Operation Type Note
name
DM DM OPC drum motor Drives the OPC drum and the transfer section. DC brushless motor
THV THV Transfer high voltage High voltage for transfer
DHV DHV High separation voltage High voltage for separation of paper
-1.8KV -1.8KV
-800V -800V
25 A 45ppm 25 A 45ppm
19 A 31/35ppm 19 A 31/35ppm
MAX 5KV MAX 5KV
200M 200M
Separation operation The transfer cleaning voltage and the developing positive bias are
Since paper with toner images transferred on it is positively applied to the OPC drum at the timing shown below so that
charged, a high negative voltage is applied to the separation elec- remaining toner on the transfer roller is attracted again to the OPC
trode to separate the paper from the drum. drum, performing cleaning.
1) When the power is turned on:
Separation electrode
CLEANING READY CONDITION
-1.8KV
WARMING UP
PRINTING Job
25 A 45ppm
19 A 31/35ppm
MAX 5KV 3) After printing 100 sheets (during 1 job)
200M 1sec 1sec
PRINTING (100 Sheets) CLEANING PRINTING (100 Sheets) CLEANING
4
5
3
2
4
3
(2) Maintenance and parts replacement 2) Remove the transfer lock pawl, and pull out the transfer roller
unit.
No. Unit Parts
a Transfer roller unit 1 After-transfer star ring ✕
2 Discharge plate ✕
3 Transfer roller ✕
4 Transfer roller collar ✕
5 TR bearing (F/R) ✕
6 TR gear ✕
a-4
a-1
a-5
a-6
a-3
a a-2
a-4
a-1. After-transfer star ring
a-5
1) Remove the transfer roller unit.
a. Transfer roller unit 2) Remove the transfer rear star ring.
1) Pull out the left door.
CN6
9604S-08C
DM TM1 1 DSW-F
2 DSW-F
3 GND2
4 GND2
5 DM\
6 DM-T
7 DMCLK\
8 (NC)
HUS-DV CN7
173981-2
TH-DV BK
1 TMA
BK
2 TMB
1 CN5
3 TCS BR
B8B-PH-K-S
1 GND2
GY
2 +5VCRU
BL
3 CRUCLK
BR
4 CRUSDA
5 PSPS\
6 +24V1
1 2 3 3 7 (NC)
8 +24V1
CN8
QR/P8-12S-C(01) B11B-PH-K-S
BR
1 DVCH1 1 1 DVCH1
BR
2 DVCH2 2 2 DVCH2
BR BR
3 DVCH3 3 3 DVCH3
BR BR
51021-0400 4 TH-DV 4 4 TH-DV
GY GY
(NC) 1 5 GND2 5 5 GND2
GY
+24V1 2 6 GND2 6 6 GND2
BR BR
TCS 3 7 TCS 7 7 TCS
GY GY
GND2 4 8 GND2 8 8 GND2
RD RD
HUS-DV BL
9 +24V1 9
BL
9 +24V1
TH-DV TCS ZHR-4 10 +5V2 10 10 +5V2
BR BR
+5V2 1 11 HUS-DV 11 11 HUS-DV
WH WH
HUS-DV 2 12 DVBias 12
GND2 3
#187
TH-DV 4 Bias
SRA-21T-3
Bias PCU PWB
Signal
Code Name Function/Operation Type Note
name
HUS-DV HUS-DV Developing humidity sensor Developing section peripheral humidity Humidity sensor Analog detector
detection
TH-DV TH-DV Developing temperature Temperature detection around the Thermistor Analog
thermistor developing unit
TCS TCS Toner density sensor Toner density detection Magnetic sensor Analog detector
DM DM Drum motor Drives the drum/developing section. DC brushless motor
TM1 TM Toner motor Drives the toner hopper. Synchronous motor
Bias Bias Developing bias High voltage for developing bias
layer
Aluminum CGL
CTL
Drum
-500V
(-470V)
4 5
No. Unit Parts 1) Release the lock, and pull out the left door.
a DV cartridge 1 Developer ▲ 2) Open the front door.
2 DV blade ✕
3 DV side seal F ✕
4 DV side seal R ✕
5 Toner density sensor
6 Temperature/humidity sensor
b 1 Toner cartridge
2 Toner motor
b-2
a-6
a-4 3) Put down the DV guide handle, release the lock, and remove
a-1 the DV cartridge.
a-5
b-1
a
a-3
a-2
0mm
Reference
(Step)
0.5mm
0mm 0.5mm
Reference
0.5mm 0.5mm
Reference Reference
0mm 0mm
0mm 0.5mm 0.5mm 0mm
Reference Reference
a-2. DV blade
1) Remove the DV cartridge.
2) Remove the DV blade.
4) Remove the coupling and the spring from the toner motor.
Paper
Copy Fusing
exit
Power/
Filter PWB
B-5 SMP-04V-NC+SMR-04V-N
B-1
B-4 BR BR
B-2 1 RTH1 1
B-3 GY GY
B-2
B-3
BR
2 GND2 2
BR
PCU
B-4 3 RTH2 3
B-1
B-5
GY
4 GND2 4
GY PWB
CN14
VLP-03V+VLR-03V CN2 B16B-PH-K-S
WH
BR
1 1
WH
1 HL1 1
AC/DC B7B-PH-K-S
RD
1 FW
2 2 2 HL2 2 2 +24VPR
BK +24VPR 1
3 3 3 L2 3 BR
4 4
GY PWB (NC) 2 3 HLPR
+12V2
HLPR 3 4
BR
HLCNT1 4 5 HLCNT1
CN1 BR
HLCNT2 5 6 HLCNT2
B03P-VL BR
SRA-51T-4 SRA-51T-4 MSW MON 6 7 RTH1
1 HL1 GY
DCCNT/ 7 8 GND2
2 HL2 BR
9 RTH2
L2
FILTER PWB 3 GY
10 GND2
L2out BK 11 (NC)
3 VLP-03V+VLR-03V
CN1 WH CN5 12 (NC)
(NC) 2 1 HL1 1
B03P-VL(RD) WH B12P-HL-A BR
L2in BK 13 MSW MON
1 2 HL2 2 RD
BK +24V1 1 14 BUP_PR
3 L2 3 RD
GY +24V2 2
TAIWAN ONLY BK +24V3 3
15 GND
16 GND
REACTOR BR +5V1 4
PWB WH
CN1
+5V2 5
OR
CN17
+3.3V1 6 B9P-VH
B03P-VL RD
WH OR
HL-1N 1 +3.3V1 7 1 +24V1
1 HL1 RD
WH GY
HL-2N 2 GND2 8 2 +24V2
CN2 2 HL2 GY
BK GY
B03P-VL HL-L 3 GND2 9 3 GND2
3 L2
GY
GND2 10 4 +5V2
L2 BK GY
1 L #187(BK) GND2 5 +5V2
11
(NC) BR OR
2 FW 6 +3.3V1
12
(NC) L2R #187(BK) OR
CN1 3 7 +3.3V1
B2P4-VH L2R BK GY
4 8 GND2
GY
GND2
200V ONLY 9
CN9
9604S-08C
1 DSW-F
2 DSW-F
3 GND2
4 GND2
5 +5V2
6 GND2
7 MM\
8 MM-T
MM 7 6 5 2 7,8
9
Rth1 8
Rth2
HLTS HL2
8FE-ST-VK-N
DSW-L 8 HL1
DSW-L 7
GND1 6
GND1 5
+5V2 4
GND2 3
MM\
MM-T
2
1
10 4 3 1 9
1 Heater lamp 1 Generates heat and transmits heat to the heat roller. The temperature is controlled by the
thermistor. (Temperature control is made mainly on the center.)
2 Heater lamp 2 Generates heat and transmits heat to the heat roller. The temperature is controlled by the
thermistor. (Temperature control is made mainly on both sides.)
3 Upper heat roller Transmits heat to melt toner on paper and fuse toner by means of a pressure with the lower heat
roller.
4 Lower heat roller Fuses toner on paper by means of a pressure with the upper heat roller.
To improve fusing capability, the diameter is greater than the conventional ones.
(ø30mm→ø40mm)
5 Fusing upper separation pawl Prevents winding of paper around the upper heat roller.
6 Fusing lower separation pawl Prevents winding of paper around the lower heat roller.
7 Thermistor (Center) Detects the surface temperature of the upper heat roller.
(On/off of heater lamp 1 is controlled according to the detected temperature.)
8 Thermistor (Side) Detects the surface temperature of the upper heat roller.
(On/off of heater lamp 2 is controlled according to the detected temperature.)
9 Thermostat When an abnormal temperature of the upper heat roller is detected, the heater lamp power is
interrupted.
To supply power again, press the switch on the top.
10 Cleaning roller Cleans toner on the lower heat roller. The blast process is employed.
PCU MM
---------
Paper exit
2
8 5
7
4
8
5
a a-2
a-9
a-8
a-4
a-6
a-5
a-1. Lower separation pawl
a-3 1) Remove the fusing unit.
a-1 a-7 2) Open the fusing rear lower PG, and remove the lower separa-
a-10 tion pawl.
a-6
a-3
a. Fusing unit
1) Pull out the left door.
A. General
This section picks up paper in the cassette and feed it to the trans-
port roller section.
The capacity of the paper feed tray is 550 sheets for 64g/m2 or
500 sheets for 80g/m2.
There are three kinds of the paper feed desk: 3-stage paper feed
a-10. Thermostat
desk (AR-D27), 2-stage paper feed desk (AR-D28), and 1-stage
1) Remove the fusing unit.
paper fed desk (AR-MU2). For details, refer to the AR-D27/D28/
2) Open the fusing unit. MU2 Service Manual.
3) Remove the fusing rear upper PG.
4) Remove the heater lamp.
5) Remove the upper heat roller.
6) Remove the screw, and remove the electrode plate and the
thermostat.
CN2
173979-2 173979-2 CSS PWB CN1
S4B-PH-K-S
OR 1 BR
LUMB 1 LUMB CSS 1
LUMA 2
OR 2
LUMA CSS GND2 2
GY
BR
LUMB 3
BR
LUMA 4
LUM 179228-3(AMP)
+5V2 1
LUD 2
GND2 3
179228-3(AMP)
+5V2 1
PED 2
MM CPFC GND2 3
LUD
PED
2
3
1
PHNR-02-H+BU02P-TR-P-H
BR
2 CPFC\ 1
RD
1 +24V1 2
CN13
PHNR-09-H+BU09P-TR-P-H
B24B-PHDSS-B
GY
GND2 1 1 +5V2 9
RD
+24V1 2 2 PPD1 8
BR
PCU PWB PED 3
BR BL
3 GND2 7
BL
CPFC\ 4 4 +5V2 6
BL BR BR
+5V2 5 5 LUD 5
GY GY
+24V1 6 6 GND2 4
CN9 GY BL BL
9604S-08C GND2 7 7 +5V2 3
8FE-ST-VK-N BR BR
1 DSW-F RRC\ 8 8 PED 2
DSW-L 8 BR GY GY
2 DSW-F LUD 9 9 GND2 1
DSW-L 7
3 GND2 +24V1 10
GND1 6 BL
4 GND2 +5V2 11
GND1 5
5 +5V2 TRC\ 12
+5V2 4
6 GND2 GND 13
GND2 3 BR
7 MM\ CSS 14
MM\ 2
8 MM-T GND2 15
MM-T 1 GY
GND2 16
PPD1 17
BR
LUMB 18
+5V2 19
BR
LUMA 20
CFM1\ 21
GND2 22
+24V1 23
2 1 4
GND2 24
3 6
Signal
Code Name Function/Operation Type Note
name
CPFC CPFC Paper feed clutch Paper freed tray section roller ON/ Electromagnetic clutch
OFF control
LUM LUM Paper feed tray lift-up motor Drives the lift plate of the paper feed DC brush motor Selection of Rotation
tray. mode/ Brake mode
PED PED Defector Paper empty detection
LUD LUD Defector Paper tray upper limit detection
CSS1
CSS2
CSS4
CSS3
CSS1
CSS2
CSS4
CSS3
(Remaining quantity sensor status change when the tray is moving up and remaining quantity)
2/3 area
sensor logic HIGH
3/3 area
sensor logic LOW
2
1
4
3
a-7
a-8 a-5
a-6
a-2 a-1 2) Disengage the pawl, and remove the paper guide.
a-4 a-3
4) Disengage the pawl, and remove the separation roller and the
torque limiter.
2) Remove the connector, and remove the cassette detection
PWB.
a-5. Paper feed cassette upper limit detection a-8. Lift-up motor
a-6. Paper feed cassette paper empty detection 1) Remove the screw, and remove the rear cabinet.
1) Pull out No. 1 paper feed tray unit, and remove the paper
guide.
2) Remove the screw, and remove the pickup roller arm.
3) Remove the paper feed roller and each part.
4) Remove the pickup roller shaft, and remove the pickup roller
guide.
5) Remove the actuator.
6) Remove the connector, the paper feed cassette upper limit
detection, and the paper feed cassette paper empty detection.
2) Remove the connector and the screw, and remove the lift-up
motor unit.
A. General
In this paper transport section, paper fed from each paper feed
port is transported to the resist roller section, where the lead edge
of the paper is aligned with the lead edge of images on the OPC
drum. Images are transferred onto paper in the transfer section,
and the paper is discharged face-up or face-down through the fus-
ing section.
o m
o u.c
y
a ls4
u
m an
179228-3
BL
3 +5V2
BR
1 POD2
GY
2 GND2
179228-3
BL
CN4 3 +5V2
BR
B32B-PHDSS-B 1 POD3
BR GY
/POMXB 1 2 GND2
BL
+5V2 2
BR RD
/POMB 3
POD1 4
BR
BR RD
SFPS-41T-187 DSW-L
/POMA 5
GND2 6
GY
BR
POD3
/POMXA 7 PHNR-03-H+BU03P-TR-P-H
BL
+5V2
+24V1
8
9
RD
RD
BR
3 +24V1 1 POD2 5
POD2 10
BR
RD
GY
2 VFM2\
1 GND2
2
3
POM
+24V1 11
GND2 12
GY
POD1
GND2 13
BL
+5V2
CFM2\
14
15
VFM2
BR
POD3 16
+24V1 17
GY
GND2 18
+24V1
CFM2\
19
20
MM
RD
+24V1 21
VFM2\
+24V1
22
23
RD RRC
GY
GND2 24
(NC) 25
GND2
DSW-L
26
27
RD 4
DSW-L 28
(NC) 29
(NC)
(NC)
30
31
TRC
DSW-F 32 2
CN9
GY HVR
PCU PWB 9604S-08C 8FE-ST-VK-N PWB
DSW-F 1 8 DSW-L
DSW-F 2 7 DSW-L
GND2 3 6 GND1
GND2 4 5 GND1
+5V1 5 4 +5V2 PPD1
GND2 6 3 GND2
MM\ 7 2 MM\
MM-T 8 1 MM-T
PHNR-02-H+BU02P-TR-P-H
CN13
B24B-PHDSS-B
BR
1 RRC\ 2
1
RD
GND2 1 2 +24V1 1
+24V1
PED
2
3
PHNR-03-H+BU03P-TR-P-H
BR
4 5
CPFC\ 1 TRC1\ 3
4
+5V2 2 (NC) 2
5 RD
RD 3 +24V1 1
+24V1 6
GND2 7
BR PHNR-09-H+BU09P-TR-P-H PHNR-03-H+BU03P-TR-P-H 179228-3(AMP)
RRC\ 8
BL BL BL
LUD 9 1 +5V2 9 1 +5V2 3 1 +5V2
RD BR BR BR
+24V1 10 2 PPD1 8 2 PPD1 2 2 PPD1
GY GY GY
+5V2 11 3 GND2 7 3 GND2 1 3 GND2
BR
TRC\ 12 4 +5V2 6
GND 13 5 LUD 5 3
CSS 14 6 GND2 4
GY
GND2
GND2
15
16
7 +5V2
8 PED
3
2
GY HVR
PPD1 17
BR
9 GND2 1 PWB
LUMB 18
+5V2 19
BL CFM1
LUMA 20
BR
CFM1\ 21
GY
GND2 22
RD PHNR-03-H+BU03P-TR-P-H
+24V1 23 TSR-04V-K PHR-3
GY GY RD RD
GND2 24 1 GND2 +24V1 1 3 +24V1 1
RD DRAWER CFM1\ 2 BR BR
2 +24V1 2 CFM1\ 2
GY GY GY
3 GND2 PWB GND2 3 1 GND2 3
BR
4 CFM1\
Signal
Code Name Function/Operation Type Note
name
POD1 POD1 Paper exit detector 1 Paper exit detection from fusing Transmission Paper transport system sensor
type
POD2 POD2 Paper exit detector 2 Paper pass detection from paper exit Transmission Paper transport system sensor
type
POD3 POD3 Paper exit detector 3 Paper exit detection to upper section Transmission Paper transport system sensor
paper exit tray (Full detection) type
POM POM Paper exit motor Drives the paper exit roller. Stepping Selection of Normal speed/
motor High speed/ Reverse rotation
VFM2 VFM2 Fusing cooling fan motor Discharges heat generated in the DC brushless PWM control
fusing section. motor
CFM1 CFM1 Fusing cooling fan motor Discharges heat generated in the DC brushless PWM control
fusing section to cool it. motor
C. Operational descriptions
[Paper transport path and paper exit]
Paper transport path with an option installed
1.
2.
4) Paper is taken into the machine again, passed over the reverse gate, and transported to the duplex unit.
5) When duplex printing is made, the ADU gate solenoid switches to the upper side of the ADU paper exit gate to switch the paper path to
the ADU.
6) When paper is discharged to the left tray or when paper is transported to the console finisher (AR-FN7), the ADU gate solenoid
switches to the upper side of the ADU paper exit gate to switch the paper path to the ADU.
Metal
Sponge
2
4
1
2
5
∗ When installing the fan, check the left door indication arrow and
c. Left door unit note the fan direction.
1) Remove the screw, and remove the left door unit. c-3. Drawer PWB
1) Remove the left door unit.
2) Remove the left door transport paper guide.
3) Remove the screw, and the reverse gate unit and remove the
angle.
3) Remove the screw, and remove the paper exit upper cabinet.
4) Remove the screw, and remove the left rear cabinet.
5) Remove the screw, and remove the front left upper cabinet.
∗ When installing the fan, check the indication arrow and note the
d-3. Left door open/close detection
fan direction.
1) Remove the paper exit reverse unit.
d-7. After-fusing roller
2) Remove the connector and the screw, and remove the left
1) Remove the paper exit reverse unit.
door open/close detection.
2) Remove the E-ring and the parts.
3) Remove the connector and the screw, and remove the paper
exit drive frame.
3) Remove the E-ring, and remove the paper exit roller. Remove
the bearing, the gear, and the parallel pin.
5 1
2
6
10
BD PM
PCU 3
PWB 4 8
MFP MOTHER CN2
SLD30R-1 7
CN16 CN2
CONTROL BOARD 30 +12V2 S32B-PHDSS-B S32B-PHDSS-B
29
28
PCU_VCCW
GND TEST3 1
BR
32
45 sheets (35 sheets)
TEST3
9
BR
PWB PWB 27
26
DTR_PCU
GND
TEST2
GND2
2
3
GY
31
30
TEST2
GND2
CN1
S11B-PH-K-S
PHNR-03-H+BU03P-TR-P-H
BR 45 sheets (35 sheets)
25 DSR_PCU /SYNC 4 29 /SYNC RD RD
GY +24V1 11 3 +24V1 1
24 GND GND2 5 28 GND2 BR BR
23 TXD_PCU GND2 6
GY
27 GND2
VFM1\ 10
GY
2 VFM1\ 2
GY VFM1
GY GND2 9 1 GND2 3
22 GND GND2 7 26 GND2 RD
BR +24V1 8 POWER SOURCE
21 RXD_PCU LSU_S/H 8 25 LSU_S/H BR
BR VFM1\ 7 PHNR-03-H+BU03P-TR-P-H SECTION
20 POF VRB 9 24 VRB GY RD
GY GND2 6
19 MSW_MON GND2 10 23 GND2 RD 3 +24V1 1
GY +24V1 5 BR
CN1 CN2
18 GND GND2 11
BR
22 GND2 PMCLK\ 4
BR 2 VFM1\ 2
GY VFM1
17 RES_PCU TEST 12 21 TEST BR 1 GND2 3
BR READY(READY\) 3
16 GND VIDEO 13 20 VIDEO BR
LBR START\ 2
15 HSYNC /VIDEO 14 19 /VIDEO GY
BR GND2 1
14 GND /LDON 15 18 /LDON PHR-5
GY
13 DTEN GND2 16 17 GND2
GY 1 PMCLK
12 BUR_PR GND2 17 16 GND2
2 READY
11
10
GND2
VIDEO1
+5V2
GND2
18
19
BL
GY
15
14
+5V2
GND2
LSU 3 START\
BL 4 GND2
9 VIDEO0 +5V2 20 13 +5V2
RD 5 +24V1
8 GND +24V1 21 12 +24V1 CN3
RD
7 +5V1 +24V1 22 11 +24V1 S4B-PH-K-S B4B-PH-K-S
BR BR
6 +5V2 /VFM1 23 10 /VFM1 GND2 1 4 GND2
GY LB
5 +5V2 GND2 24 9 GND2 SYNC\ 2 3 SYNC\
BR BR
4 +5V2 /START 25 8 /START GND2 3 2 GND2
BR BL
3 +5V2 /VFM1 26 7 /VFM1 +5V2 4 1 +5V2
BR
2 +5V2 /PMCLK 27 6 /PMCLK
BR
1 +12V1 /READY 28 5 /READY
GY
GND2 29 4 GND2
GY
GND2 30 3 GND2
BL
+5V LD 31 2 +5V LD
GY
GND2 32 1 GND2
1
Signal
Code Name Type Function/Operation NOTE
name
PM PM Polygon mirror (motor) Reflects laser beams at the constant rotation speed.
BD BD PWB Detects the laser scan start timing. This device is used
to detect a laser trouble.
a-1
5) Remove the connector, the screw, and the angle. Remove the
snap band.
∗ Do not disconnect the LSU side.
10) Remove the connector and the screw, and remove the duct
holding cover.
6) Pull out the No. 1 paper feed tray unit, and push up and
remove the front door.
7) Release the lock, and pull out the left door. Remove the
screw, and remove the front cover right.
11
MIM
6
2
1 CCD PWB
3
4
CL1
5
MHPS
10
CN1 CN2
SLD5R-1 SLD5S-1
GND2 5 1 GND2
GND2 4 2 GND2
/CL1 3 3 /CL1 CN11
+24V3 2 4 +24V3 S3B-PH-K-S 53053-0310(MOLEX)
LB
+24V3 1 5 +24V3 MHPS 1 1 MHPS
GY
GND2 2 2 GND2
BL
+5V2 3 3 +5V2
10 4 12 9 7 8 11
5 3 1 6
C. Operational descriptions
(1) CCD/lens unit
This machine employs the reduction optical-type line CCD (Charge Coupled Device) of scan resolution of 600dpi and 7450 pixels.
CCD scan is performed by shifting the scan positions sequentially by the carriage unit (lamp and mirror) scan or moving the document with
the SPF.
Lights reflected by the document are reflected by each mirror to form images on CCD elements through the reduction-type lens. The CCD
converts the optical energy into electrical energy (analog). (Photoelectric conversion)
(2) CIS unit
The image sensor which scans back document images is attached to the SPF. The close-contact type image sensor (Contact Image Sen-
sor) with scan resolution of 600dpi and 7196 pixels is employed.
For the CIS to scan documents, the scan position is sequentially shifted by shifting the document by the SPF, and the LED light in the unit
is radiated to the back of the document, and photo energy is converted into electric energy (analog signal).
CIS
Auto-focus lens
Lens center line
LED PWB
Glass
CIS UNI
Focus point
SPFM
1030mS
SRRC
SPPD4
94mS
SPOD
55mS
181mS
CCD
CIS
manuals4you.com
2 1
5
2
5
4
3
4
2)
1)
1)
3)
4)
3)
4)
6) 5)
4) 1)
1)
3)
2)
a-5. Mirror
1) Remove the table glass.
2) Clean mirror.
3) 4)
3)
2)
1)
1)
3)
2)
1)
2)
1)
3)
4) 1)
3)
1)
2)
3) 1)
2)
5)
2)
2)
1) 4)
3)
1)
b-3. Lamp
1) Remove the table glass.
2) Slide the lamp unit base to the notch section.
1) 1)
2)
1) 1)
1)
3) Flip the notch section Mylar and remove the screw. Slide the
lamp holder to the front side, and remove it upward from the
rear side. Remove the connector.
1)
2)
3)
(+) direction
Reference line
(-) direction
1 scale: 1.4mm
7. DSPF section
SCOV
OCSW
SDSS SPLS2
4
SPED
SPLS1
SPFS 7
SPPD SPFVR
SPFM 3
SPFC
9
SRRC
8
10
5
2
STMP
12
SPOD
CIS unit
SOCD
11
1
CN1 CN3
TX24-100R-LT-H1 TX25-100P-LT-H1
CNC CN10
CND CN3
PHNR-6-H+BU6P-TR-P-H B26B-PHDSS-B S28B-PHDSS
B6B-PH-K-S 9604S-35F
6 /B 1 2 /B +24V3 7 1 +24V3
VLED 35
5 +24V3 2 4 +24V3 +24V3 8 2 +24V3
DGND 34
4 B 3 1 B GND2 5 3 GND2
VAS 33
3 A 4 3 A GND2 6 4 GND2
DGND 32
2 +24V3 5 5 +24V3 5 +5V1
VDS 31
1 /A 6 6 /A +5V2
GND2
4
9
6
7
+5V2
GND2
SCN DGND
SCN
30
29
1754873+179228-3 VAREF 17 8 VAREF
DGND 28
+5V1 1 SPPD 19 9 SPPD
SPED
GND2
2
3
SPFC
SPED
18
21
10
11
SPFC
SPED
JNT LGATE
DGND
CLK
27
26
25
1754873+179228-3 SDSS 12 12 SDSS
CNB DGND 24
+5V2
SCOV
1
2
PHNR-11-H+BU11P-TR-P-H
1 +5V1 11
B22B-PHDSS-B
5 +5V
SCOV
SRRC
SPWS
23
14
24
13
14
15
SCOV
SRRC
SPWS
PWB CIS DATA
DGND
23
22
GND2 3 2 SPED 10 16 SPED
SPFS 16 16 SPFS
(1/2) LD 21
1754873+179228-3 3 GND2 9 1 GND2 DGND 20
+5V2
SPPD
1
2
4
5
6
+5V2
SCOV
GND2
8
7
6
7
18
+5V2
SCOV
SPFMO0 3
17
18
19
GND2
GND2
SPFMO0
cnt SCLK
DGND
19
18
GND2 2 GND2 /LST 17
3 SPOD 20 SPOD
7 +5V2 5 8 +5V2 25 DGND 16
/SPFMA 2 21 /SPFMA
SMP-02V-NC+SMR-02V-N
1 +24V3 1
8
9
10
SPPD
GND2
+24V3
4
3
2
14
3
11
SPPD
GND2
+24V3
SOCD
SPFMA
26
1
22
23
SOCD
SPFMA
PWB SD0
DGND
SD1
15
14
13
2 /SDSS 2 11 /SDSS 1 SPLS1 22 24 SPLS1 12
15 /SDSS DGND
/SPFMB 11 25 /SPFMB 11
9 +5VPOD SD2
4 GND2 SPLS2 20 26 SPLS2 10
DGND
20 SPOD SPFMB 13 27 SPFMB 9
B3B-PH-K-S PHNR-6-H+BU6P-TR-P-H SD3
10 +5V2 SPFSET 15 28 SPFSET 8
+5VPOD 1 6 +5VPOD 1 DGND
GND2 10
GND2 2 5 GND2 2 22 SOCD SD4 7
CN7 CN1
SPOD 3 4 SPOD 3 6 GND2 DGND 6
S26B-PHDSS B26B-PHDSS
3 +5V2 4 12 +24V3 2_DATA1- 2_DATA1- 1 SD5 5
1754873+179228-3 1
2 SOCD 5 19 /SPFC 2_DATA1+ 2_DATA1+ 2 DGND 4
+5V2 1 2
1 GND2 6 13 +24V3 2_DATA0- 2_DATA0- 3 SD6 3
SOCD 2 3
17 /SRRC 2_DATA0+ 2_DATA0+ 4 DGND 2
GND2 3 4
21 (NC) 2_CLK- 2_CLK- 5 SD7 1
5
PHNR-2-H+BU2P-TR-P-H 2_CLK+ 6
2 +24V3
1 /SPFC
1
2
SPF 6
7
8
2_CLK+
2_DBL-
2_DBL+
2_DBL-
2_DBL+
7
8
9 GND2 GND2 9
PHNR-3-H+BU3P-TR-P-H
10 FRM_CCD2 FRM_CCD2 10
3 +24V3
2 (NC)
1 /SRRC
1
2
3
PWB 11
12
CLK_CCD2
PAGE2
CLK_CCD2
PAGE2
11
12
13 ADD_CCD2 ADD_CCD2 13
14 TXD_CCD2 TXD_CCD2 14
SMR-03V-NC+SMP-03V-N 15 RES_CCD2 RES_CCD2 15
16 RXD_CCD2 RXD_CCD2 16
1 VAREF 1
17 +3.3V +3.3V 17
2 SPWS 2
CNA 18 +3.3V +3.3V 18
3 GND2 3
B12B-PHDSS-B 19 +24V3 +24V3 19
1754873+179228-3 1 VAREF 20 GND2 GND2 20
+5V2 1 2 SPWS 21 +12V1 +12V1 21
SPLS1 2 9 GND2 22 GND2 GND2 22
GND2 3 5 +5V2 23 +5V2 +5V2 23
4 SPLS1 24 GND2 GND2 24
1754873+179228-3 12 GND2 25 +5V2 +5V2 25
+5V2 1 7 +5V2 26 /CIS_SET /CIS_SET 26
SPLS2 2 6 SPLS2
GND2 3 10 GND2
PHNR-2-H+BU2P-TR-P-H
11 +24V3
3 /SPFS
SCN
2 +24V3 1
1 /SPFS 2
SRA-01T-3.2
c
GY
cnt
SRA-21T-3
a
GY GY
b
FG PWB
SRA-21T-3
CN6
179228-4+175694-4 B4B-PH-K-S
RD
+24V3 1 1 +24V3
BR
/STMPS 2 2 /STMPS
LB
/STSET 3 3 /STSET
GY
GND2 4 4 GND2
12
1 5 10 8
11
Signal
Code Name Function/Operation Type Note
name
SCOV SCOV SPF cover switch SPF cover open/close detection Transmission type Sensor
SPFM SPFM1 SPF paper feed motor, paper Drives the paper feed roller and the Stepping motor
transport motor transport roller. (SPF)
SPFC SPFC SPF paper feed clutch SPF paper feed section roller ON/OFF Electromagnetic clutch
control
SRRC SRRC SPF resist roller clutch SPF resist roller ON/OFF control Electromagnetic clutch
SPED SPED SPF document set detector SPF document presence detection Transmission type Sensor
SPPD SPPD SPF document paper pass detector SPF document paper pass detection 1 Transmission type Sensor
SPFS SPFS SPF document pickup solenoid SPF document pickup Solenoid
STMP STMP FAX finish stamp solenoid Drives the FAX document finish stamp. Solenoid
SPLS1 SPLS1 SPF document length detector 1 SPF document length detection (Short) Transmission type Sensor
SPLS2 SPLS2 SPF document length detector 2 SPF document length detection (Long) Transmission type Sensor
SPFVR SPFVR SPF document size (Width) SPF document size (Width) detection Volume resistor Other
detection analog data detector detector
SOCD SOCD SPF open/close detector SPF unit open/close detection Transmission type Sensor
SPOD SPOD SPF paper exit detector SPF paper exit detection Transmission type Sensor
Note 2: Replacement reference: Replace by using the SPF counter value as an indication.
Paper feed section pickup roller, paper feed roller, separation pad, separation lower mylar lower:
100K or 1 year
7
7
4
1
3
2
6
5
2)
1)
5) 1)
5)
3) 4) a-2. SPF document resist front sensor
5)
a-3. SPF paper feed cover sensor
3)
4)
2)
4) 4)
3)
3)
4)
1) 3)
2)
a-5. SPF control PWB
2)
1) Remove the SPF PWB, and remove the SPF control PWB.
1)
2)
3)
a-1. SPF document stopper solenoid 3) 4)
1) Remove the upper transport unit cover. 3)
4)
4)
2) 5)
1)
1)
2)
1)
1)
3)
4)
3)
2) Remove the original length sensor cover, and remove the sen-
sor.
1)
2)
1)
1)
2) 4)
1)
3)
4)
3)
1)
2)
1)
2)
5)
4)
2) 3)
For easy installation of the cover, slide the earth line to the con- 1)
nector side when attaching.
3) Remove the paper exit frame, and remove the paper exit
Note: The CIS unit is factory-adjusted before shipping.
roller.
Since these adjustments cannot be performed in the
market, never touch the following screws of the CIS unit. 5)
6)
a a a
3)
7)
2)
1)
3)
4)
3)
1) 1)
1) 3)
1) 1) 1)
2)
3)
1)
4)
2)
1) 2)
2)
2)
3)
2)
2)
2)
2) Remove the SPF resist roller and the SPF resist roller clutch.
2)
2)
1)
2)
3)
1)
2)
1)
1)
2)
3) Remove the screw, and remove the separation plate and the
front separation plate.
3) Remove the SPF pickup unit.
4) Remove the separation Mylar lower, and the separation pad.
2)
1)
1) 1)
4) Remove the original paper feed solenoid and the SPF original 8. Operation panel section
paper feed clutch.
3)
2) 4)
1)
A. General
This section describes various types of settings, display and oper-
ation.
The LCD display section is controlled by the MFP CONTROL
PWB.
The touch panel, operation keys and LED display are controlled by
the SCANNER CONTROL PWB.
ORSLED
OCSW
2
ORS PD
/CCFT
TOUCH
LCD
1
CN3 CN1
TX25-100P-LT-H1 BOARD TO BOARD TX24-100R-LT-H1
GND2 1 1 GND2
GND2 2 2 GND2
/1_DBL- 3 3 /1_DBL-
/1_DBL+ 4 4 /1_DBL+
1_CLK- 5 5 1_CLK-
1_CLK+ 6 6 1_CLK+
1_DATA0- 7 7 1_DATA0-
1_DATA0+ 8 8 1_DATA0+ SCN
SCN 1_DATA1-
1_DATA1+
GND2
9
10
11
9 1_DATA1-
10 1_DATA1+
11 GND2
GND2
GND2
12
13
12 GND2
13 GND2
cnt
JNT GND2
GND2
14
15
14 GND2
15 GND2
GND2
(NC)
16
17
16 GND2
17 (NC)
PWB
CN4
20FLS-SM1-TB
PWB +12V1
+24V3
18
19
18 +12V1
19 +24V3 (1/3)
1 GND2
(1/2) +24V3 20 20 +24V3
PDSEL1 21 21 PDSEL1
2 (NC) PDSEL2 22 22 PDSEL2
CN1 CN5
3 (NC) 30FMZ-BT 30FMN-BT /KEYIN 23 23 /KEYIN
4 (NC) XH 30 1 XH SEG0 24 24 SEG0
5 (NC) GND2 25 25 GND2
/YL 29 2 /YL
GND2 26 26 GND2
6 GND2 /XL 28 3 /XL LcdS+ 27 27 LcdS+
7 LCD D3 YH 27 4 YH LcdS- 28 28 LcdS-
8 LCD D2 /CCFT 26 5 /CCFT LcdM+ 29 29 LcdM+
9 LCD D1 +24V3 25 +24V3 LcdM- 30 30 LcdM-
6
LcdCP1+ 31 31 LcdCP1+
10 LCD D0 GND2 24 7 GND2 32 LcdCP1-
LcdCP1- 32
11 GND2 TH 23 8 TH LcdCP2+ 33 33 LcdCP2+
12 LCD-VEE 34 LcdCP2-
13 3.3V
LVDS GND2 22 9 GND2 LcdCP2-
LcdD0+
34
35 35 LcdD0+
LcdD3- 21 10 LcdD3-
LcdD0- 36 36 LcdD0-
14 Lcd DIS LcdD3+ 20 11 LcdD3+
15 GND2
PWB LcdD2- 19 12 LcdD2-
LcdD1+
LcdD1-
37
38
37 LcdD1+
38 LcdD1-
16 LCD CP2 LcdD2+ 18 13 LcdD2+ LcdD2+ 39 39 LcdD2+
17 GND2 LcdD1- 17 14 LcdD1- LcdD2- 40 40 LcdD2-
LcdD3+ 41 41 LcdD3+
18 LCD CP1 LcdD1+ 16 15 LcdD1+
LcdD3- 42 42 LcdD3-
19 LCD M LcdD0- 15 16 LcdD0- GND2 43 43 GND2
20 LCD S LcdD0+ 14 17 LcdD0+ GND2 44 44 GND2
LCD-VEE 13 18 LCD-VEE YH 45 45 YH
/XL 46 46 /XL
3.3V 12 19 3.3V
/STSET 47 47 /STSET
CN2 LcdDIS 11 20 LcdDIS /STMPS 48 48 /STMPS
FFC-4PIN 04FM-1.0ST GND2 10 21 GND2 GND2 49 49 GND2
(X2) 1 /YL GND2 50 50 GND2
LcdCP2- 9 22 LcdCP2-
(Y2) CN6
2 XH LcdCP2+ 8 23 LcdCP2+
GND2 51 51 GND2
GND2 52 52 GND2 S6B-PH-K-S H3P-SHF-AA+B3P-SHF-1AA
(X1) 3 YH BL BL
GND2 7 24 GND2 +12V1 53 53 +12V1 +5V1 1 1 +5V1
(Y1) 4 /XL GY GY
LcdCP1- 6 25 LcdCP1- +12V1 54 54 +12V1 GND2 2 2 GND2
LB LB
LcdCP1+ 5 26 LcdCP1+ GND2 55 55 GND2 OCSW 3 3 OCSW
+5V2 56 RD
56 +5V2 +24V3 4
LcdM- 4 27 LcdM- BR RD
CN3 GND2 57 57 GND2 /LED0 5
S02(8.0)B-BHS-L LcdM+ 3 28 LcdM+ +5V2 58 58 +5V2 LB BR
/LED1 6
/CCFT 1 1 /CCFT LcdS- 2 29 LcdS- GND2 59 59 GND2 LB
HV 2 2 HV LcdS+ 1 30 LcdS+ +3.3V 60 60 +3.3V
FRM_CCD1 61 61 FRM_CCD1
CLK_CCD1 62 62 CLK_CCD1
TXD_CCD1 63 63 TXD_CCD1
RES_CCD1 64 64 RES_CCD1
CN101 CN4 RXD_CCD1 65 65 RXD_CCD1
T24FAZ-SMT-TF T24FAZ-SMT-TF ADD_CCD1 66 66 ADD_CCD1
GND2 24 1 GND2 GND2 67 67 GND2
CN102 PDSEL0 23 2 PDSEL0 PAGE1 68 68 PAGE1
S6B-PH-K-S B6B-PH-SM3-TB GND2 69 69 GND2
BR PDSEL1 22 3 PDSEL1
PDSEL0 1 1 PDSEL0 GND2 70 70 GND2
LB PDSEL2 21 4 PDSEL2 /CL1 71 71 /CL1
PDSEL1 2 2 PDSEL1
PL +5V2 20 5 +5V2 PDSEL0 72 72 PDSEL0
PDSEL2 3 3 PDSEL2
BL 19 6 PD +5V2 73 73 +5V2
+5V2 4 +5V2 PD
4 PD 74 74 PD
BR GND2 18 7 GND2
PD 5 5 PD SEG1 75 75 SEG1
GY +5V2 17 8 +5V2 SEG2 76 76 SEG2
GND2 6 6 GND2
/KEYIN 16 9 /KEYIN GND2 77 77 GND2
SEG0 15 10 SEG0 /F0 78 78 /F0
MFP SEG1 14 11 SEG1
GND2 79 79 GND2
80 /F1
/F1 80
OPE SEG2 13 12 SEG2 GND2 81 81 GND2
/F0 12 13 /F0 /F2 82 82 /F2
/F1 11 14 /F1 GND2 83 83 GND2
PWB /F2 10 15 /F2
/F3 84 84 /F3
GND2 85 85 GND2
/F3 9 16 /F3 /BZR 86 86 /BZR
GND2 8 17 GND2 GND2 87 87 GND2
GND2 7 18 GND2 +5V1 88 88 +5V1
Lcd DIS 89 89 Lcd DIS
GND2 6 19 GND2
+3.3V 90 90 +3.3V
(NC) 5 20 (NC) GND2 91 91 GND2
(NC) 4 21 (NC) LCD-VEE 92 92 LCD-VEE
/BZR 3 22 /BZR TH 93 93 TH
/CCFT 94 94 /CCFT
+5V1 2 23 +5V1
/YL 95 95 /YL
GND2 1 24 GND2 XH 96 96 XH
+24V3 97 97 +24V3
+24V3 98 98 +24V3
GND2 99 99 GND2
GND2 100 100 GND2
C. Maintenance and parts replacement 3) Remove the document size detection PWB (Light emitting
side)
No. Unit Parts
a Original detection 1 Original size detection PWB 1)
1)
unit (Light emitting side) 1)
2 Original size detection PWB
(Light receiving side)
b Operation panel 1 LVDS PWB
unit 2 MFP operation PWB
2)
3)
a-1
a-2
b-2
b-1
a-2. Original size detection PWB (Light receiving side)
b 1) Remove the operation panel lower cabinet.
2) Remove the original size detection PWB (Light receiving side)
a. Original detection unit
a-1. Original size detection PWB (Light emitting side)
2)
1) Remove the rear cabinet. 2)
1)
2) Remove the original detection unit (Light emitting side). 2)
3)
3) 2)
1)
2)
1)
2)
1)
1)
1) 2)
1)
4) Remove the operation panel lower cabinet. 1)
2)
2)
2)
2)
3)
1)
2)
1)
1)
1)
1)
2)
1)
1)
2)
1)
a-1
a-1
a-1
a-4
b-1
a-3
b-2
a-2
PS front roller
section
4) Remove the connector and the screw, and remove the main Apply grease FLOIL G484
drive unit.
a-2. Paper cassette paper feed clutch
a-3. Paper transport clutch
a-4. Resist roller clutch
1) Remove the main drive unit.
2) Remove the parts.
a-1. Gears
1) Remove the main drive unit.
2) Remove the screw, and remove the drive cover.
b-2
b-4
a-1
b-3
b-1
a-2 a-3
a
a. Power unit
b-1. Drum motor 1) Remove the main switch mounting plate.
b-2. Main motor 2) Remove the screw, and remove the right cabinet.
1) Remove the screw, and remove the rear cabinet.
2) Remove the connector and the screw, and remove the drum
motor and the main motor.
(Taiwan only)
6) Remove the connector, the screw, and the angle. Remove the
snap band.
2) Release the lock, and pull out the left door. Remove the
screw, and remove the front cover right. 3) Remove the screw, and remove the cooling fan motor.
∗ When installing the fan, check the indication arrow and note the
fan direction.
2) Remove the connector and the screw, and remove the inlet 12. PWB
mounting plate.
A. Maintenance and parts replacement
No. Unit Parts
a 1 MFP controller PWB
2 HDD (Option)
3 PCU PWB
4 Mother PWB
a-1
3) Remove the connector and the screw, and remove the fuse a-2
PWB.
a-3 a-4
3) Remove the screw, and remove the paper exit upper cabinet.
4) Remove the screw, and remove the left rear cabinet. ∗ When installing the fan, note the fan direction.
5) Remove the screw, and remove the front left upper cabinet. 12) Remove the connector and the screw, and remove the control-
ler cooling fan motor 2.
6) Remove the screw, and remove the paper exit tray cabinet.
7) Remove the screw, and remove the front right upper cabinet.
∗ When installing the fan, note the fan direction.
8) Remove the front door.
a-3. Ozone exhaust fan motor
1) Pull out the left door.
2) Remove the rear cabinet.
3) Remove the paper exit upper cabinet, the left rear cabinet, and
the front left upper cabinet.
4) Remove the paper exit tray cabinet, the front right upper cabi-
net, and the front door.
5) Remove the screw, and remove the controller duct.
6) Remove the connector and the screw, and remove the ozone
exhaust fan motor.
9) Remove the screw, and remove the cooling fan duct upper.
∗ When installing the fan, check the indication arrow and note the
fan direction.
<Adjustment specification>
Specification
Marking position Measure from 54.2mm
the P surface above.
SIMULATION 64-1
Center line
SELF PRINT MODE. SELECT 0-7, AND PRESS START.
0. TRAY SELECT :1 1. PRINT START
2. PRINT PATTERN:87 3. DENSITY :1 1
4. MULTI : 1 5. MODE :1
6. LEVEL : 1 7. DUPLEX :1
Standard paper of A3
SIMULATION 50-10
PRINT OFF-CENTER ADJUSTMENT. SELECT 0-8, AND PRESS
START.
0.TRAY SELECT 1 1.COPY START
2.MAGNIFICATION 100
2
(ADJUSTMENT DATA)
3.TRAY1 50 4.TRAY2 50 5.TRAY3 50
6.TRAY4 50 7.BPT 50 8.ADU 50
3) Check the lead edge void area on the self print pattern 2) Make a copy at the normal ratio (100%) and check the lead
edge void area and the image loss. (Enter 100 as the set value
(SIM67-1).
of the copy magnification ratio (MAGNIFICATION), and press
(Enter 1 and press [START] key.) [START] key.)
4) If the adjustment result is not satisfactory, perform the follow- 3) If the adjustment result is not satisfactory, perform the follow-
ing procedures.
ing procedures.
∗ If the lead edge void area is not 3.5mm:
∗ If the lead edge void are is not 3.5mm:
Change the adjustment value of RRCB and perform the
Change the adjustment value of RRCB and perform the
adjustment. (Change the adjustment value of RRCB and
adjustment. (Change the adjustment value of RRCB and
press [START] key.)
press [START] key.) (1msec/step)
(Shift for the adjustment value change: 0.1mm/step)
∗ If the lead edge image loss is not 1.5mm:
SIMULATION 50-5 Change the adjustment value of RRCA and perform the
LEAD EDGE ADJUSTMENT. SELECT 0-20, AND PRESS START. adjustment. (Change the adjustment value of RRCA and
0.TRAY SELECT 1 1.PRINT START press [START] key.)
(ADJUSTMENT DATA)
LEAD EDGE: 2.RRCB 50 3.SIDE2 ADJ. 50
2 (Shift for the adjustment value change: 0.2mm/step)
RESIST: 4.T1 50 5.T2 50 6.DESK 50 (Rear edge void area adjustment)
7.BPT 50 8.ADU 50 Adjust so that the rear edge void area is 3.5mm. (Change the
OFF CENTER: 9.T1 50 10.T2 50 11.T3 50 12.T4 50
13.BPT 50 14.ADU 50 adjustment value of TRAIL EDGE, and press [START] key.)
(Front/rear frame direction image loss adjustment)
(VOID SETTING) 15.LEAD_EDGE(DENA) 50
16.TRAIL_EDGE(DENB) 30 17.FRONT/REAR 30 Set the adjustment value of SIDE to 20. (Enter 20 as the adjust-
ment value of SIDE, and press [P] key.)
<Specification> When the adjustment value is changed, the image position is
shifted in the front/rear frame direction.
Set position Specification Set value
(Front/rear frame direction void area adjustment)
Self print lead Print start A = 4.0mm or less Shift of
edge position A of (Lead and tail 0.175mm Adjust so that the total of the front/rear direction void areas is
adjustment the output total: 8.0mm or (35ppm) / 7.0mm. (Change the adjustment values of FRONT/REAR, and
SIM 50-5 pattern 1 less) 0.225mm press [START] key.)
(45ppm) for Front frame void area = 3.5mm Rear frame void area = 3.5mm
set value 1. If, as shown above, the front and the rear void areas are not even,
use SIM 50-5 to adjust the image off-center position.
Print
lead edge A
• In the case of Fig. 1
Shift cam A in the direction A by the difference in the copy image.
For one scale (one groove), shift by 0.5mm.
After shifting, tighten the fixing screw (M3 x 12) of cam A and
make a copy again, and check the copy again to insure that there
B. Adjustment on the scanner side is no distortion.
<1> OC scan distortion adjustment • In the case of Fig. 2
Items which must have been completed before this adjust- Shift cam A in the direction B by the difference in the copy image.
ment. For one scale (one groove), shift by 0.5mm.
• Adjustment on the engine side (If there is no problem in self After shifting, tighten the fixing screw (M3 x 12) of cam A and
print, no need to adjust.) make a copy again, and check the copy again to insure that there
Items which must be executed after completion of this adjust- is no distortion.
ment. After adjustment, tighten the fixing screw (M3 x 12) and the scan-
• OC scan off-center ner fixing screw (M4 x 8).
• OC scan lead edge adjustment ∗ If the above adjustment does not fix the problem, perform the
1) Make a test chart as shown below. (Make a self-print pattern MB rail adjustment.
71.) ∗ After the OC distortion adjustment, perform SIM53-8 SPF scan-
ning position automatic adjustment.
<2> SPF height adjustment
Items which must have been completed before this adjust-
ment.
• Nothing special
Items which must be executed after completion of this adjust-
2) Make a copy from the table glass, and check it. ment.
At that time, set the test chart correctly. If it is set in a distorted • Nothing special
position, the adjustment cannot be made correctly. 1) Close the (D)SPF.
3) If the output value is not in the specified range, perform the fol- 2) Check to confirm that the dove and the reference plate in the
lowing adjustment. figure below are in contact with the table glass (point a) and
4) Adjust the distortion. the side guide (point b). (Place copy paper under the dove and
Use a level gauge to check that the scanner is installed hori- pull it out.) If they are not in contact, adjust with the set screw.
zontally.
Make a copy and check it. If there is any distortion as shown in
Fig. 1 or Fig. 2, loosen the scanner fixing screw (M4 x 8) and
the cam A fixing screw (M3 x 12) and adjust.
SIMULATION 51-2
RESIST TIMING ADJUSTMENT. SELECT 0-8, AND PRESS START.
0.TRAY SELECT 1 1.PRINT START
2.TRAY1 60 3.TRAY2 50 4.DESK 50
5.BPT 55 6.ADU 50
7.SPF(HIGH) 60 8.SPF(LOW) 75
1
5) Though the SPF resist amount is the above value, if there is
any distortion in SPF scan, adjust the SPF installing position in
the following procedures.
6) Loosen the nut which is fixing the adjustment set screw of the
hinge R, and adjust the adjustment set screw.
7) Make a copy again, and check again that the value is in the
specified range.
b 8) Tighten the nut to fix the adjustment screw.
a
a b
a
a b
b
b
<Specification>
Adjustment a
Specification
position
Distance between 3-point contact Hinge <Specification>
dove (Reference (Left front/Left rear/Right adjustment set
plate) and table front when viewed from screw Specification Adjustment position
glass the front) Skew feed Within ±3mm Hinge R adjustment screw
∗ After the SPF distortion adjustment, perform SIM53-8 SPF
<3> SPF scan distortion adjustment
scanning position automatic adjustment.
Items which must have been completed before this adjust-
ment. <4> OC scan magnification ratio adjustment
• Adjustment on the engine side (If there is no problem in self Items which must have been completed before this adjust-
print, no need to adjust.) ment.
• OC scan distortion adjustment • Adjustment on the engine side (If there is no problem in self
• SPF height adjustment print, no need to adjust.)
Items which must be executed after completion of this adjust- • OC scan distortion adjustment
ment. Items which must be executed after completion of this adjust-
• SPF off-center ment.
• SPF lead edge adjustment • OC scan lead edge adjustment
• Front/rear and left/right void amount setting • Original off-center adjustment
1) Make a test chart as shown below. (Print a self-print pattern 1) Place a print of self-print pattern (A3 or WLT) 70 or a scale on
71.) the table glass.
2) Make a copy with DSPF. 2) Close the original cover, and make a copy.
3) Check that it is in the specified range. 3) Check that the value is within the specification.
4) If the value is not within the specified range, execute SIM48-1
(item 3, 4).
5) Make a copy again and check again that the value is within the
specification.
Adjustment Adjustment
Specification SIMULATION 48-1
position value
MAGNIFICATION ADJUSTMENT. INPUT VALUE 0-99, AND PRESS
Main scan direction ±0.5% SIM48-1 Set value 1: START.
magnification ratio (3, 4) 0.1% change 4.CCD(SUB) 50
CCD (MAIN)
Sub scan direction Press [START] key.
Select 1, and Press [CUSTOM SETTINGS] key,
magnification ratio press [START] key. or terminate copying.
CCD (SUB)
<5> SPF scan magnification ratio SIMULATION 48-1
MAGNIFICATION ADJUSTMENT. NOW COPYING.
Items which must have been completed before this adjust-
ment.
Press [START] key, or
• Adjustment on the engine side (If there is no problem in self Select 0, and press [START] key. press [CUSTOM SETTINGS] key.
print, no need to adjust.)
• OC scan distortion adjustment SIMULATION 48-1
• SPF scan distortion adjustment MAGNIFICATION ADJUSTMENT. SELECT 1-15, AND PRESS START.
(FEED TRAY)
• OC scan magnification ratio
1.TRAY1 2.TRAY2 3.TRAY3 4.TRAY4
• SPF height adjustment 5.BPT 6.LCC 1
Items which must be executed after completion of this adjust- (ABOVE+10: DUPLEX MODE)
ment.
Select 2, and Press [START] key, or
• SPF scan lead edge adjustment
press [START] key. press [CUSTOM SETTINGS] key.
• Original off-center adjustment
1) Set a chart of print pattern 70 on SPF/DSPF. SIMULATION 48-1
2) Make a copy. (In the case of DSPF back copy, make a single MAGNIFICATION ADJUSTMENT.
copy in the duplex mode.) (MAGNIFICATION)
3) Check that the output paper satisfies the specifications. INPUT 25-400(%) 100
4) If the value is not within the specified range, execute SIM48-1
<Specifications>
(item 5, 6).
5) Make a copy again, and check that the output paper satisfies Adjustment Adjustment
Specifications
the specifications. position value
SPF sub scan direction ±0.5% SIM 48-1 Set value 1:
magnification ratio (5, 6) 0.1% change
SPF (SUB)
DSPF main scan
(back) direction
magnification ratio
CIS (MAIN)
∗ The SPF main scan direction magnification ratio is common with
OC.
Specification ± 1.5mm
SIMULATION 50-12
ORIGINAL OFF-CENTER ADJUSTMENT. SELECT 0-9, AND PRESS
START.
0.TRAY SELECT 1
2.MAGNIFICATION 100
1.COPY START 2
(ADJUSTMENT DATA)
3.PLATEN 50 4.SPF SIDE1 50 5.SPF SIDE2 50
Paper
exit
direction
Original Copy
A3 white paper
SIMULATION 41-1
Adjust screw
PD SENSOR CHECK..
Front side
OCSW PD1 PD2 PD3 PD4 PD5 PD6 PD7
SIMULATION 41-2
PD SENSOR ADJUSTMENT. SELECT1-2, AND PRESS START.
(PLEASE OPEN THE ORIGINAL COVER.)
1. NO ORIGINAL
2. A3 ORIGINAL
1
Select 1 and
32±0.5mm press [START] key. Press [CUSTOM SETTINGS] key.
SIMULATION 41-2
PD SENSOR ADJUSTMENT.
NO ORIGINAL ··· COMPLETE (or "ERROR at PD1 PD2...")
A3 ORIGINAL ··· INCOMPLETE
SIMULATION 41-3
<Specification>
PD SENSOR DATA DISPLAY.
OCSW Specification Adjustment
PD1[128]: 200 PD2[128]: 200
PD3[128]: 50 PD4[128]: 52 Document size detection photo COMPLETE SIM 41-2
PD5[128]: 51 PD6[128]: 50 sensor adjustment
PD7[128]: 52
SIMULATION 46-2
EXP. LEVEL SETUP (2). SELECT 3-6, AND PRESS START. SIMULATION 46-9
(EXP. LEVEL SELECT) EXP. LEVEL SETUP (CHAR.2). SELECT 1-5, AND PRESS START.
3. AE 3.0
5. MIX 3.0
4. CH 3.0
6. PHOTO 3.0
1 (FEED TRAY)
1. TRAY1 2. TRAY2 3. TRAY3 4. TRAY4
• Adjustment spec
SIMULATION 46-9
Chart Adjustment Chart Adjustment EXP. LEVEL SETUP (CHAR.2). SELECT 3-11, AND PRESS START.
Mode EXP. (EXP. LEVEL SELECT)
No. level No. level
3. 1.0 4. 1.5 5. 2.0
Character 3 3 Copied 2 Not copied 6. 2.5 7. 3.0 8. 3.5
Character/ 3 3 Copied 2 Not copied 9. 4.0 10. 4.5 11. 5.0 1
Photo
Photo 3 3 Copied 2 Not copied 2) Press the COPY button to make a copy
Auto 3 Copied 2 Not copied Check that the copy density is as shown in the table below. If not,
If the copy density is too light, increase the adjustment value. change the adjustment value.
If the copy density is too dark, decrease the adjustment value. For the auto mode, there is only one adjustment value. For the
Adjustment range: 30 - 170 other modes, the adjustment value for each density level must be
adjusted.
(2) Adjusting the print quality in fax mode
This adjustment is needed in the following situations:
• The CCD unit has been replaced.
• U2 trouble has occurred.
• The MFP control PWB has been replaced.
• The EEPROM on the MFP control PWB has been replaced.
• The scanner control PWB has been replaced.
• The EEPROM on the scanner control PWB has been replaced.
• One or more parts of the scanner (reading) section have been
replaced.
SIMULATION 46-14
EXP.LEVEL SETUP FAX(FINE).SELECT 0-14,AND PRESS START.
0.TRAY SELECT 1 1.PRINT START
2.EXP LEVEL 1
3.AUTO 50 4.1.0 50 5.2.0 50
1
6.3.0 50 7.4.0 50 8.5.0 50
00 9.AUTO(H) 50 10.1.0(H) 50 11.2.0(H) 50
12.3.0(H) 50 13.4.0(H) 50 14.5.0(H) 50
2) Go through the simulation modes that correspond to the Fax SIMULATION 46-14
modes for which to adjust the print density (i.e., the modes EXP.LEVEL SETUP FAX(FINE),INPUT VALUE 0-99, AND PRESS
START.
specified in Simulations 46-13, -14, -15, -16, or -45).
4.1.0 50
SIMULATION 46-13 Select 1, Press [START] key.
and press Press [CUSTOM SETTINGS] key,
EXP.LEVEL SETUP FAX(NORMAL). SELECT 0-8, AND PRESS [START] key. or terminate copying.
START.
0.TRAY SELECT 1 1.PRINT START
2.EXP LEVEL 1
1 SIMULATION 46-14
EXP.LEVEL SETUP FAX(FINE). NOW PRINTING.
3.AUTO 50 4.1.0 50 5.2.0 50
6.3.0 50 7.4.0 50 8.5.0 50
Press [START] key,
Select 0, and press [START] key. or press [CUSTOM SETTINGS] key.
SIMULATION 46-13
EXP.LEVEL SETUP FAX(NORMAL). SELECT 1-5, AND PRESS
START.
(FEED TRAY)
1.TRAY1 2.TRAY2 3.TRAY3 4.TRAY4
5.BPT
1
(ABOVE +20:DSPF MODE)
SIMULATION 46-13
EXP.LEVEL SETUP FAX(NORMAL). SELECT 3-8, AND PRESS START.
(EXP.LEVEL SELECT)
3.AUTO 4.1.0 5.2.0
6.3.0 7.4.0 8.5.0 1
SIMULATION 53-7
SPF TRAY ADJUSTMENT(MANUAL). SELECT 1-4, AND PRESS SIMULATION 53-6
START. SPF TRAY ADJUSTMENT.
1.MAX.POSITION: 66 POSITION 2 ... COMPLETE (or “ERROR”)
2.POSITION 1 : 456
3.POSITION 2 : 713 1 Select 4, and press [START] key. Press [CUSTOM SETTINGS] key.
4.MIN.POSITION: 791
SIMULATION 53-6
Press [START] key. Press [CUSTOM SETTINGS] key. SPF TRAY ADJUSTMENT.
MIN.POSITION ... COMPLETE (or “ERROR”)
SIMULATION 53-7
SPF TRAY ADJUSTMENT(MANUAL). INPUT VALUE 0-1023, AND
PRESS START.
1.MAX.POSITION 66
2. Code-type simulation
A. Operating procedures and operations
∗ Entering the simulation mode
1) Copy mode key ON → Program key ON → Asterisk (*) key ON
→ CLEAR key ON → Asterisk (*) key ON → Ready for input of
a main code of simulation
2) Entering a main code with the 10-key → START key ON
3) Entering a sub code with the 10-key → START key ON
4) Select an item with the scroll key and the item key.
5) The machine enters the mode corresponding to the selected
item.
Press START key or EXECUTE key to start the simulation
operation.
To cancel the current simulation mode or to change the main
code and the sub code, press the user setup key.
∗ Canceling the simulation mode to return to the normal mode
1) Press CA key.
NO Do you YES
Operation is made according want to end the Press the clear all key.
to the selected mode and item. simulation ?
NO
The display is made according to
the selected some and the item.
NO
The selected mode and
the item are cleared.
4. LOW SPEED
SIMULATION 2-1
SPF AGING TEST. EXECUTING···.
Press [START] key, and the
operation is started.
Press [CUSTOM SETTINGS] key, and
scanning is stopped.
1. HIGH SPEED 2
2. LOW SPEED
SIMULATION 1-1
SCANNER CHECK. EXECUTING···. 2-2
1. TOP SPEED
2. HIGH SPEED
Purpose Operation test/Check
3. MIDDLE SPEED Function Used to check the operations of the sensors and
4. LOW SPEED 1 (Purpose) detectors in the automatic document feeder unit
and the related circuits.
Section DSPF
1-2 Item Operation
Operation/Procedure
Purpose Operation test/Check
The operating conditions of the sensors and detectors are dis-
Function Used to check the operation of sensor and
played.
(Purpose) detector in the scanning (read) section and the
related circuit. The active sensors and detectors are highlighted.
Section Optical (Image scanning) SPFSET SPF sensor
Item Operation SOCD Open/close sensor
Operation/Procedure SCOV Paper feed cover sensor
The sensor and detector operation conditions are displayed. SPED Document set sensor
The active sensors and detectors are highlighted. SPPD Resist front detection sensor
• The scanner (read) unit is in the home position.: "MHPS" section SPOD Document paper exit sensor
is highlighted. SWDn Document width sensor (n → 1 (inside) - 6
(outside))
• The scanner (read) unit is not in the home position.: "MHPS" is
normally displayed. SPLSn Document length sensor (n → 1 (inside) - 2
(outside))
MHPS Optical system home position CISSET CIS installation detection
STSET Stamp unit installation sensor
SIMULATION 1-2 SWD_LEN SPF guide plate position (unit: 0.1mm)
SCANNER SENSOR CHECK.. SWD_AD SPF document width detection volume output AD
MHPS value
SIMULATION 3-2 2
FINISHER SENSOR CHECK.
FSSS FJS FFDSW FTCS FFDS
FSPS FSUC FSS FSTHPS FSHPS FLE FLLLS
FULS FFE FFES FFRHPS FFHPS FFPS FSLS 3-6
FBES FOBHPS FAS FRJHPS FFJHPS FARHPS FPHPS Purpose Adjustment
FES
Function Used to adjust the stacking capacity of the
(FPE)(FPSHPS)(FPUC)(FPDS)(FPDSS4)(FPDSS3)(FPDSS2)
(FPDSS1)(FPTS) (Purpose) finisher. (Used to adjust the alignment plate
(jogger) stop position in the finisher paper width
( ) : Added when the punch unit is installed. direction. The adjustment is made by changing the
alignment plate home position in the paper width
direction by software.)
3-3
Section Finisher
Purpose Operation test/Check Item Operation
Function Used to check the operation of the load in the Operation/Procedure
(Purpose) finisher and the control circuit.
Enter the adjustment value with 10 digit key pad and press START
Section Finisher key. The jogger moves to LT position (Inch series) or A4 position
Item Operation (AB series) according to the entered value, and stops there.
Operation/Procedure
1) Select the number corresponding to the target of operation SIMULATION 3-6
check with 10-key. FINISHER JOGGER ADJUSTMENT. INPUT VALUE 40-60, AND PRESS START.
Press [START] key, and the operation Press [CUSTOM SETTINGS] key, and SIMULATION 3-21
is started. the operation is stopped. MAIL BOX LOAD TEST. SELECT 1-8 AND PRESS START.
1.MM
2.GSOL1
3.GSOL2
2
SIMULATION 3-10
CONSOLE FINISHER SETTING. INPUT VALUE, AND PRESS START. 4.GSOL3
1.FOLDING POSITION 5.GSOL4
200 6.GSOL5
7.GSOL6
8.GSOL7
3-20 Press [START] key, and the operation Press [CUSTOM SETTINGS] key, and
is started. the operation is stopped.
Purpose Operation test/Check
Function Used to check the mail bin stacker sensor.
(Purpose) SIMULATION 3-21
MAIL BOX LOAD TEST. EXECUTING....
Section Mail bin stacker
1.MM
Item Operation 2.GSOL1
3.GSOL2
2
Operation/Procedure
4.GSOL3
The operating conditions of the sensors and detectors are dis- 5.GSOL4
played. 6.GSOL5
7.GSOL6
The active sensors and detectors are highlighted. 8.GSOL7
MPFD1 Tray 1 paper full detection
MPFD2 Tray 2 paper full detection
MPFD3 Tray 3 paper full detection
MPFD4
MPFD5
Tray 4 paper full detection
Tray 5 paper full detection
4
MPFD6 Tray 6 paper full detection
MPFD7 Tray 7 paper full detection 4-2
MPFD8 Tray 8 paper full detection Purpose Operation test/Check
MPID Interface unit paper entry detection Function Used to check the operations of the sensors and
MPPD1 Paper transport sensor 1 (Purpose) detectors in the paper feed section (desk paper
MPPD2 Paper transport sensor 2 feed/large capacity tray) and the related circuit.
MPPD3 Paper transport sensor 3 Section Paper feed
MPPD4 Paper transport sensor 4 Item Operation
MPPD5 Paper transport sensor 5
Operation/Procedure
M24VM 24V power supply
The operating conditions of the sensors and detectors are dis-
MDD1 Jam cancel door
played.
MDOPD Interface unit door
The active sensors and detectors are highlighted.
SIMULATION 3-20
MAIL BOX SENSOR CHECK.
MPFD1 MPFD2 MPFD3 MPFD4 MPFD5 MPFD6 MPFD7
MPFD8 MPID MPPD1 MPPD2 MPPD3 MPPD4 MPPD5
M24VM MDD1 MDOPD
<LCC>
SIMULATION 4-3
TDRS Tandem side door sensor LCC LOAD TEST. SELECT 1- , AND PRESS START.
TTSD Tandem tray sensor 1.
TLUD2 Tandem tray 2 upper limit sensor 2
TLUD1 Tandem tray 1 upper limit sensor
TSPD2 Tandem tray 2 remaining quantity sensor
Press [START] key, and the operation Press [CUSTOM SETTINGS] key, and
TSPD1 Tandem tray 1 remaining quantity sensor is started. the operation is stopped.
TPED2 Tandem tray 2 paper sensor
TPED1 Tandem tray 1 paper sensors
TPFD3 Tandem paper transport sensor 3 SIMULATION 4-3
LCC LOAD TEST. EXECUTING....
TPFD2 Tandem paper transport sensor 2 1.
MCSS4 MP tray size detection 4 2
MCSS3 MP tray size detection 3
MCSS2 MP tray size detection 23
MCSS1 MP tray size detection 1
MCSPD MP tray remaining quantity detection
MCLUD MP tray upper limit detection
MCPED MP tray paper empty detection
TPFD1 MP tray transport detection
SIMULATION 4-2
LCC SENSOR CHECK.
o m
u.c
TDRS TTSD TPFD1 TPFD2
TPFD3 MCLUD TLUD1 TLUD2
MCSPD TSPD1 TSPD2 MCPED
y o
ls4
TPED1 TPED2 MCSS1 MCSS2
MCSS3 MCSS4
u a
m an
SIMULATION 5-3
COPY LAMP TEST. SELECT 1-2, AND PRESS START.
After 6.0sec Press [CUSTOM SETTINGS] key, 1.COPY LAMP
and the operation is stopped. 2.CIS 1
SIMULATION 5-1 Press [START] key, and the operation Press [CUSTOM SETTINGS] key, and
is started. the operation is stopped after 10sec.
SIMULATION 5-3
5-2 COPY LAMP TEST. EXECUTING···.
1.COPY LAMP
Purpose Operation test/Check 2.CIS 1
Function Used to check the operation of the heater lamp
(Purpose) and the control circuit.
Section Fixing (Fusing)
Item Operation
Operation/Procedure
1) Select the number corresponding to the target of operation 6
check with 10-key.
2) Press [START] key. 6-1
The load selected in procedure 1 performs ON/OFF operation.
Purpose Operation test/Check
Press [CUSTOM SETTINGS] key to stop the operation of the Function Used to check the operation of the paper transport
load. (Purpose) system loads and the control circuit.
The ON/OFF operation of the selected heater lamp is Section Paper transport (Discharge/Switchback/Transport)
repeated every 500ms five times. Item Operation
1 HL1 (LOWER) Heater lamp 1 (Lower) Operation/Procedure
2 HL2 (UPPER) Heater lamp 2 (Upper) 1) Select the number corresponding to the target of operation
check with 10-key.
SIMULATION 5-2 2) Press [START] key.
HEATER LAMP TEST. SELECT 1-2, AND PRESS START.
The load selected in procedure 1 operates.
1.HL1(LOWER)
2.HL2(UPPER) 2 Press [CUSTOM SETTINGS] key to stop the operation.
1 MSWPR MSW power relay signal
2 HLPR Heater power relay
Press [START] key, and the Press [CUSTOM SETTINGS] key, and
3 DCPR DC power relay
operation is started. the operation is stopped.
The operation is repeated the specified 4 MM Main motor
number of times before stopping. 5 DM Drum motor
6 POM_FW Paper exit motor forward rotation
7 POM_RV Paper exit motor reverse rotation
SIMULATION 5-2
8 CPFC Paper feed clutch
HEATER LAMP TEST. EXECUTING···.
1.HL1(LOWER)
2 9 RRC Resist roller clutch
2.HL2(UPPER) 10 TRC Transport roller clutch
11 FGS_FIN Finisher gate solenoid
12 LUM Tray 1 lift-up motor
13 TRC_DSK Desk clutch sync signal
14 PSPS Separation pawl solenoid
15*1 MCM MP drive motor control signal
16*1 MCPCL MP tray paper feed clutch signal
17*1 MCFCL MP tray transport clutch signal
SIMULATION 6-2
FAN MOTOR CHECK.. Press [START] key to start registration and operation.
2.FMLo The operation mode is kept until the power is turned off or setting is made again.
2
Press [START] key, Press [CUSTOME SETTING] key, Press [START] key. Press [CUSTOM SETTINGS] key.
and time count is started. and time count is stopped.
SIMULATION 8-1
SIMULATION 7-8
DV BIAS SETTING. INPUT VALUE, AND PRESS START.
WARM UP TIME DISPLAY. WARMING UP,PLEASE WAIT.
1:AUTO (0-745)
(UNIT:sec)
485
30
Warm-up is completed. Press [CUSTOM SETTINGS] key. Press [START] key. Press [CUSTOM SETTINGS] key.
Or after 30sec output.
SIMULATION 7-8
WARM UP TIME DISPLAY. WARM UP COMPLETED. SIMULATION 8-1
(UNIT:sec) DV BIAS SETTING. EXECUTING···.
60 1:AUTO
485
9 10
9-1 10-1
Purpose Operation test/Check Purpose Operation test/Check
Function Used to check and adjust the operation of the load Function Used to check the operations of the toner motor
(Purpose) (clutch/solenoid) in the duplex section and the (Purpose) and the related circuit.
control circuit. Section Process (Developing)
Section Duplex Item Operation
Item Operation
Operation/Procedure
Operation/Procedure
1) Select the number corresponding to the target of the operation
1) Select the number corresponding to the target of the operation check with 10-key.
check with 10-key.
2) Press [START] key.
2) Press [START] key.
The load selected in procedure 1) is operated for 10sec.
The load selected in procedure 1) is operated.
Press [CUSTOM SETTINGS] key to stop the operation.
Press [CUSTOM SETTINGS] key to stop the operation.
NOTE: Never execute this simulation with toner in the toner hop-
1 ADMEN1 ADU motor 1 control signal per.
2 ADMEN2 ADU motor 2 control signal If executed, excessive toner will enter the developing sec-
3 DGS ADU gate solenoid tion. Be sure to remove the toner motor from the toner hop-
per before execution.
14
16
14-0
16-0
Purpose Clear/Cancel (Trouble etc.)
Function Used to cancel excluding the self-diag U1/LCC/ Purpose Clear/Cancel (Trouble etc.)
(Purpose) U2/PF troubles. Function Used to cancel the self-diag U2 troubles.
Item Trouble Error (Purpose)
Operation/Procedure Section MFP control PWB, PCU PWB, scanner control
1) Select 1 (YES) with 10-key. PWB
Item Trouble
2) Press [START] key. (The trouble display is canceled.)
Operation/Procedure
1 YES After canceling the trouble other than U1, U2, PF,
1) Select 1 (YES) with 10-key.
and LCC, the machine returns to the main code
entry standby mode. 2) Press [START] key. (The trouble display is canceled.)
2 NO Without canceling the trouble, the machine returns 1 YES After canceling the U2 trouble, the machine returns
to the main code entry standby mode. to the main code entry standby mode.
2 NO Without canceling the trouble, the machine returns
SIMULATION 14 to the main code entry standby mode.
TROUBLE CANCELLATION. (OTHERS)
ARE YOU SURE?
1. YES 1 SIMULATION 16
U2 TROUBLE CANCELLATION.
2. NO ARE YOU SURE?
1. YES 1
2. NO
21 SIMULATION 22-1
COUNTER DATA DISPLAY.
TOTAL: ******** DRUM: ******** TONER: ********
21-1 DEVE: ******** MAINTENANCE: ********
TOTAL OUTPUT: ******** COPIES: ********
Purpose Setting
PRINTER: ******** FAX OUTPUT: ********
Function Used to set the maintenance cycle. I-FAX OUTPUT:******** DOC FILING OUTPUT:********
(Purpose) RIGHT SIDE:******** OTHERS: ********
Item Specifications Counter
Operation/Procedure
1) Enter the number corresponding to the maintenance timing 22-2
display.
Purpose Adjustment/Setup/Operation data output/Check
2) Press [START] key. The condition entered in procedure 1) is (Display/Print)
set.
Function Used to check the total numbers of misfeed and
Maintenance timing display Set range (Purpose) troubles. (When the number of misfeed is
0 Default (Differs depending on the model.) 0 - 999 considerably great, it is judged as necessary for
1 - 200 Maintenance display at 1K - 200K repair. The misfeed rate is obtained by dividing
999 No maintenance display this count value with the total counter value.)
Item Trouble
Operation/Procedure
SIMULATION 21-1
MAINTENANCE CYCLE SETUP. INPUT VALUE 0-999, AND PRESS The paper jam/trouble counter value is displayed.
START.
PAPER JAM Number of paper jams
0: DEFAULT
1-200: MAINTENANCE CYCLE (1K-200K) SPF JAM Number of SPF jams
999: FREE 0 TROUBLE Number of troubles
SIMULATION 22-2
JAM/TROUBLE COUNTER DATA DISPLAY.
PAPER JAM: ******** SPF JAM: ********
TROUBLE: ********
SIMULATION 23-80
23 DATA PRINT MODE. EXECUTING....
0. TRAY SELECT :1
23-2
0
Purpose Adjustment/Setup/Operation data output/Check Select 2 and press [START] key. Press [CUSTOM SETTING] key
(Display/Print) or [START] key.
Function Used to check the trouble history of paper jam and
(Purpose) misfeed. (If the number of misfeed and troubles is SIMULATION 23-80
considerably great, it may be judged as necessary DATA PRINT MODE. INPUT VALUE, AND PRESS START.
to repair.) (PRINT PATTERN)
INPUT 1.
Item Trouble
Operation/Procedure
1
1) Select "1. PRINT START."
2) Press [START] key.
The trouble history of paper jam and misfeed is printed.
This data can be cleared by SIM 24-1.
SIMULATION 24-3
24-2 ORG./STAPLE COUNTER DATA CLEAR. SELECT 1-5, AND PRESS
START.
Purpose Data clear 1. SPF
Function
(Purpose)
Used to clear the number of use (the number of
prints) of each paper feed section.
2. SCAN
3. STAPLER
1
4. PUNCH
Section Paper feed 5. STAMP
Item Counter
Operation/Procedure
Press [START] key. Press [CUSTOM SETTINGS] key or
1) Select the counter to be cleared with 10-key. [START] key.
2) Press [START] key.
The confirmation to clear is opened. SIMULATION 24-3
3) Select Yes/NO of counter clear with 10-key. * COUNTER DATA CLEAR.
YES: Clear ARE YOU SURE?
1 1
SIMULATION 24-4
* COUNTER DATA CLEAR. SIMULATION 24-6
ARE YOU SURE? * COUNTER DATA CLEAR.
ARE YOU SURE?
1. YES
2. NO
1 1. YES
1
2. NO
* = MAINTENANCE
* = COPY
24-5
24-7
Purpose Data clear
Function Used to reset the developer counter. (The Purpose Data clear
(Purpose) developer counter of the DV unit which is installed Function Used to clear the OPC drum counter. (Perform this
is reset.) (Purpose) simulation when the OPC drum is replaced.)
Section Image process (Photoconductor/Developing/ Section Image process (Photoconductor/Developing/
Transfer/Cleaning) Transfer/Cleaning)
Item Counter Developer Item Counter Photo conductor
Operation/Procedure Operation/Procedure
1) Select the counter to be cleared with 10-key. 1) Select the counter to be cleared with 10-key.
2) Press [START] key. 2) Press [START] key.
The confirmation to clear is opened. The confirmation to clear is opened.
3) Select Yes/NO of counter clear with 10-key. 3) Select Yes/NO of counter clear with 10-key.
YES: Clear YES: Clear
NO: Not clear NO: Not clear
4) Press [START] key. 4) Press [START] key.
1 DV CARTRIDGE Developer cartridge After replacing the OPC drum, be sure to clear the OPC drum
counter.
SIMULATION 24-5 1 DRUM OPC drum counter
DEVELOPER COUNTER DATA CLEAR. PRESS START.
1. DV CARTRIDGE
SIMULATION 24-5
* COUNTER DATA CLEAR.
ARE YOU SURE?
1. YES
2. NO
1
* = DV CARTRIDGE
SIMULATION 25-1
DV MONITOR. EXECUTING···.
HUMIDITY AREA : 70.0 - 72.5
TEMPERATURE AREA: 70.0 - 72.5
DEVE REFERENCE : 128
SIMULATION 26-5
26 A3(LEDGER) COUNT UP MODE SETTING. SELECT 1-2, AND PRESS
START.
26-3
1. TOTAL COUNTER
(1: 1COUNT UP, 2: 2COUNT UP)
1
Purpose Setting
Function Used to set the specifications of the auditor.
(Purpose) Setting must be made according to the auditor use 26-6
conditions. Purpose Setting
Section Auditor Function Used to set the specifications (paper, document
Item Specifications (Purpose) detection, etc.) of the destination.
Operation/Procedure Item Specifications Destination
1) Select the number corresponding to the auditor mode with 10- Operation/Procedure
key. 1) Select the number corresponding to the destination with 10-
2) Press [START] key. key.
1 P10 Built-in auditor mode 2) Press [START] key.
2 VENDOR Coin vendor mode After completion of setting, the machine is automatically reset.
3 OTHERS Other 1 USA United States of America
4 VENDOR-EX Coin vendor mode (without temporarily 2 CANADA Canada
charge) 3 INCH Inch series EX
5 VENDOR-EX+ Coin vendor mode (without temporarily 4 JAPAN Japan
charge) + Document filing function 5 AB_B AB series B5
enable 6 EUROPE Europe
(Default: 1) 7 UK UK
8 AUSTRALIA Australia
9 AB_A AB series A5
10 CHINA China
26-35
26-10
Purpose Setting
Purpose Setting Function Used to set whether the same continuous troubles
Function Used to set the network scanner trial mode. (Purpose) are displayed as one trouble or the series of
(Purpose) troubles with SIM 22-4 when the same troubles
Item Operation occur continuously.
Operation/Procedure Section
1) Select START/END of the network scanner trial mode with 10- Item Specifications
key. Operation/Procedure
2) Press [START] key. 1) Select the number corresponding to the operation mode with
Max. 500 menus can be scanned. 10-key.
2) Press [START] key.
0 END Trial mode cancel Default
1 START Trial mode start 0 ONCE When two or more troubles of a same kind occur
continuously, the troubles are displayed as one
trouble in the trouble history of SIM22-4.
SIMULATION 26-10
NETWORK SCANNER TRIAL SETTING. SELECT 0-1, AND PRESS
1 ANY When two or more troubles of a same kind occur
START. continuously, the troubles are displayed straightly
as two or more troubles in the trouble history of
0.END
1.START
1 SIM22-4.
(Default: 0)
Purpose Setting
SIMULATION 26-52
Function Used to set the automatic magnification ratio BLANK PAPER COUNT UP SETTING. SELECT 0-1, AND PRESS
(Purpose) selection (AMS) in the pamphlet mode. START.
Section 0. NO (NO COUNT UP)
1. YES (COUNT UP)
1
Item Specifications Operation mode (Common)
Operation/Procedure
1) Enter the number corresponding to whether AMS operation is
automatically performed or nor in the center binding mode with
26-68
the 10-key.
2) Press [START] key. Purpose Setting
Function Used to set ENABLE/DISABLE of the CA key
0 NO AMS/APS selection allowed (Purpose) cancel function of print stop.
1 YES AMS is forcibly operated. Section
(Default: 1 for Europe and UK, 0 for the others) Item Specifications Operation
Operation/Procedure
SIMULATION 26-41
PAMPHLET MODE AMS SETTING. SELECT 0-1, AND PRESS 1) Select ENABLE/DISABLE of the CA key cancel function of
START. print stop with 10-key.
0. NO
1. YES
1 2) Press [START] key.
0 DISABLE Disable
1 ENABLE (PRINT STOP) Enable
(Default: 1)
26-50
Purpose Setting SIMULATION 26-68
Function Black-White reverse YES/NO setting CA KEY CANCEL MODE SETTING. SELECT 0-1, AND PRESS
(Purpose) START.
Item Specifications Operation 0. DISABLE
1. ENABLE (PRINT STOP)
0
Operation/Procedure
1) Select ENABLE/DISABLE of the B/W reverse mode with 10-
key.
2) Press [START] key.
0 DISABLE B/W reverse mode DISABLE
27
1 ENABLE B/W reverse mode ENABLE Default
27-1
SIMULATION 40-1
BYPASS TRAY SENSOR CHECK..
SIMULATION 40-2
BYPASS TRAY ADJUSTMENT. SIMULATION 40-11
POSITION 2 ··· COMPLETE (or "ERROR") TRAY3 SENSOR CHECK..
SIMULATION 40-2
BYPASS TRAY ADJUSTMENT.
MIN. POSITION ··· COMPLETE (or "ERROR")
SIMULATION 41-2
SIMULATION 40-12
PD SENSOR ADJUSTMENT.
MULTI PURPOSE TRAY ADJUSTMENT.
NO ORIGINAL ··· COMPLETE
MIN. POSITION ··· COMPLETE (or "ERROR")
A3 ORIGINAL ··· COMPLETE (or "ERROR at PD1 PD2...")
41-3
41 Purpose Operation test/Check
Function Used to check the operation of the document size
41-1 (Purpose) sensor and the related circuit. (The document size
Purpose Operation test/Check sensor output level can be monitored with the LCD
Function Used to check the operation of the document size display.)
(Purpose) sensor and the related circuit. (The operation of Section Other
the document size sensor can be monitored with Item Operation
the LCD display.) Operation/Procedure
Section Other The detection output level (A/D value) of the document sensors
Item Operation (PD1 - PD7) is displayed in real time.
Operation/Procedure ∗ The value in [ ] on the side of each sensor name indicates the
The operating conditions of sensors and detectors are displayed. threshold value.
The active sensors and detectors are highlighted. The light receiving value (A/D value) and the threshold value (A/D
value) of PD1 - PD7 are in the range of 1 - 255. The default of
OCSW Document cover Open: Normal display threshold value is 128.
status Close: Highlighted
PD1 - 7 Document detection No document: Normal display OCSW Original cover status Open: Normal display
sensor status Document present: Highlighted Close: Highlighted
PD1 - 7 PD sensor detection level The value in [ ] indicates the
adjustment threshold value (SIM41-2 adjustment
SIMULATION 41-1
PD SENSOR CHECK..
value).
OCSW PD1 PD2 PD3 PD4 PD5 PD6 PD7
44-4
43
Purpose Setup
Function Used to set the target image (reference) density
43-1
(Purpose) level in the developing bias voltage correction.
Purpose Setting Section Process
Function Used to set the fusing temperature in each (OPC drum, developing, transfer, cleaning)
(Purpose) operation mode. Item Data
Section Fixing (Fusing) Operation/Procedure
Item Operation 1) Select the number corresponding to the setting mode with 10-
Operation/Procedure key.
1) Select the number corresponding to the setting mode with 10- 2) Press [START] key.
key. 3) Enter the set value.
2) Press [START] key. 4) Press [START] key.
3) Press [CUSTOM SETTINGS] key.
Item
4) Press [START] key.
1 TEMP. AREA *1 Process environment temperature
Item Default forcible setting value
1 INSIDE NORMAL Heater inside/normal 190 (0 - 13 /normal: 0)
2 OUTSIDE NORMAL Heater outside/normal 190 2 HUMIDITY AREA *1 Process environment humidity
3 INSIDE PREHEAT Heater inside/preheat 150 forcible setting value
4 OUTSIDE PREHEAT Heater outside/preheat 150 (0 - 14 /normal: 0)
3 S_WT Vb rising correction standby time
(0 - 180 sec/default: 90)
SIMULATION 43-1
FUSER TEMPERATURE SET. SELECT 1-4, AND PRESS START.
4 Vb1 Vb correction amount (first rotation)
1. INSIDE NORMAL 190 (0 - 150V/default: 50)
2. OUTSIDE NORMAL 190 5 Vb2 Vb correction amount (second
3. INSIDE PREHEAT 150
4. OUTSIDE PREHEAT 150
1 rotation) (0-50V/default: 15)
*1: Only when this value is 0, control is made with the actual mea-
surement value of the process thermistor (temperature/humid-
Press [START] key. Press [CUSTOM SETTINGS] key. ity). When it is not 0, control is made with the forcible setting
value.
SIMULATION 43-1
FUSER TEMPERATURE SET. INPUT VALUE, AND PRESS START. SIMULATION 44-4
1. INSIDE NORMAL PROCESS CONTROL VALUE SETTING. SELECT 1-5 AND PRESS
START.
190 1.TEMP. AREA 0
2.HUMIDITY AREA 0
3.S_WT 100
3
4.Vb1 50
5.Vb2 50
SIMULATION 46-12
EXP.LEVEL SETUP FAX(AUTO SET).SELECT 1-5, AND PRESS
START.
(FEED TRAY)
1.TRAY1 2.TRAY2 3.TRAY3 4.TRAY4
5.BPT
Select 1, and
Select 2, and Press [START] key, or press [START] key. Press [CUSTOM SETTINGS] key.
press [START] key. press [CUSTOM SETTINGS] key.
SIMULATION 46-19
SIMULATION 46-18
EXP.MODE SETUP. INPUT VALUE 1-2, AND PRESS START.
GAMMA SETUP(COPIER). SELECT 3-14, AND PRESS
1.AE MODE
START.
(EXP.LEVEL SELECT) 2
3.AUTO 4.1.0 5.2.0 1
6.3.0 7.4.0 8.5.0 Select 2, 3, or 4 and Press [START] key, or
9.AUTO(H) 10.1.0(H) 11.2.0(H) press [START] key. press [CUSTOM SETTINGS] key.
12.3.0(H) 13.4.0(H) 14.5.0(H)
SIMULATION 46-19
EXP.MODE SETUP. INPUT VALUE 0-1, AND PRESS START.
2.AE STOP MODE(COPIER)
46-19 1
Purpose Adjustment
Function Used to set the auto mode operation
(Purpose) specifications in each mode (copy, scan, FAX).
Item Picture quality Density
Operation/Procedure
(Toner save operation YES/NO setting in the auto mode)
1) Select "1. AE MODE" with 1-key.
2) Press [START] key.
3) Select the number corresponding to the operation specifica-
tions with 10-key.
4) Press [START] key.
When [START] key is pressed, the adjustment value is set.
(Operation setting in the auto copy mode)
1) Select the number corresponding to the mode with 10-key.
(Select one of 2 - 4.)
2) Press [START] key.
3) Select the number corresponding to the operation mode with
10-key.
SIMULATION 46-21
∗ Normal mode (Image density adjustment level)
EXP.LEVEL SETUP SCANNER(AUTO SET), INPUT VALUE 0-99, ∗ Normal mode (Image density adjustment level) (Half-tone
AND PRESS START. mode)
0.SCANNER EXP.LEVEL 50 ∗ Auto mode
∗ Auto mode (Half-tone mode)
2) Press [START] key.
46-22
3) Enter the image density adjustment value with 10-key.
Purpose Adjustment 4) Press [START] key or press [P] key.
Function Used to adjust the scanner exposure level in the
The adjustment value is set.
(Purpose) normal text mode.
Item Picture quality Density Set
Item Default
Operation/Procedure range
0 AUTO Auto 0 - 99 50
1) Select the number corresponding to one of the following
adjustment items with 10-key. (Select one of 0 - 5.) 1 1.0 Exposure level 1
2 2.0 Exposure level 2
∗ Normal mode (Image density adjustment level)
3 3.0 Exposure level 3
∗ Auto mode
4 4.0 Exposure level 4
2) Press [START] key.
5 5.0 Exposure level 5
3) Enter the image density adjustment value with 10-key. 6 AUTO (H) Auto (Half-tone)
4) Press [START] key or press [CUSTOM SETTINGS] key. 7 1.0 (H) Exposure level 1 (Half-tone)
The adjustment value is set. 8 2.0 (H) Exposure level 2 (Half-tone)
Set 9 3.0 (H) Exposure level 3 (Half-tone)
Item Default 10 4.0 (H) Exposure level 4 (Half-tone)
range
0 AUTO Auto 0 - 99 50 11 5.0 (H) Exposure level 5 (Half-tone)
1 1.0 Exposure level 1 NOTE: Only the set value is changed and no printing is performed.
2 2.0 Exposure level 2
3 3.0 Exposure level 3 SIMULATION 46-23
4 4.0 Exposure level 4 EXP.LEVEL SETUP SCANNER(FINE). SELECT 0-11,AND PRESS
5 5.0 Exposure level 5 START.
SIMULATION 46-23
Select other than 0 - 5, and Press [START] key, or press EXP.LEVEL SETUP SCANNER(FINE). INPUT VALUE 0-99, AND
press [START] key. [CUSTOM SETTINGS] key. PRESS START.
0.AUTO
50
SIMULATION 46-22
EXP.LEVEL SETUP SCANNER(NORMAL), INPUT VALUE 0-99, AND
PRESS START.
0.AUTO 50
SIMULATION 46-25
SIMULATION 46-24 EXP.LEVEL SETUP SCANNER(ULTRA FINE). INPUT VALUE 0-99,
EXP.LEVEL SETUP SCANNER(SUPER FINE). INPUT VALUE 0-99, AND PRESS START.
AND PRESS START.
0.AUTO
50
0.AUTO
50
Purpose Adjustment
Function Used to adjust the image density in the FAX mode SIMULATION 46-45
EXP.LEVEL SETUP FAX(600dpi). SELECT 1-5,AND PRESS START.
(Purpose) (600dpi).
(FEED TRAY)
Item Picture quality 3.TRAY1 2.TRAY2 3.TRAY3 4.TRAY4
Operation/Procedure 5:BPT 1
1) Select the number corresponding to one of the following
adjustment items with 10-key. (Select one of 0 - 11.)
Select 2, and Press [START] key, or
∗ Normal mode (Image density adjustment level) press [START] key. press [CUSTOM SETTINGS] key.
∗ Normal mode (Image density adjustment level) (Half-tone
mode)
SIMULATION 46-45
∗ Auto mode
EXP. LEVEL SETUP FAX(600dpi). SELECT 3-8,AND PRESS START.
∗ Auto mode (Half-tone mode) (EXP. LEVEL SELECT)
2) Press [START] key. 3.AUTO
6.3.0
4.1.0
7.4.0
5.2.0
8.5.0
1
3) Enter the image density adjustment value with 10-key.
9.AUTO(H) 10.1.0(H) 11.2.0(H)
4) Press [START] key or press [P] key. 12.3.0(H) 13.4.0(H) 14.5.0(H)
The adjustment value is set.
Set
Item Default
range 46-46
0 AUTO Auto 0 - 99 50
Purpose Adjustment
1 1.0 Exposure level 1
Function Used to adjust sharpness of the scanner mode.
2 2.0 Exposure level 2
(Purpose)
3 3.0 Exposure level 3
Item Picture quality
4 4.0 Exposure level 4
Operation/Procedure
5 5.0 Exposure level 5
1) Enter the sharpness level with 10-key.
6 AUTO (H) Auto (Half-tone)
2) Press [START] key.
7 1.0 (H) Exposure level 1 (Half-tone)
8 2.0 (H) Exposure level 2 (Half-tone) The greater the adjustment value is, the greater the sharpness is.
9 3.0 (H) Exposure level 3 (Half-tone) Set range: 1 - 3
10 4.0 (H) Exposure level 4 (Half-tone) Default: 3 (Normal), 1 (Halftone)
11 5.0 (H) Exposure level 5 (Half-tone)
SIMULATION 48-1
MAGNIFICATION ADJUSTMENT. NOW COPYING. 48-6
Purpose Adjustment
Press [START] key, or
Select 0, and press [START] key. press [CUSTOM SETTINGS] key. Function HSYNC cycle adjustment
(Purpose)
SIMULATION 48-1 Item Picture quality
MAGNIFICATION ADJUSTMENT. SELECT 1-15, AND PRESS START.
(FEED TRAY)
Operation/Procedure
1.TRAY1 2.TRAY2 3.TRAY3 4.TRAY4 (Adjustment mode selection)
5.BPT 6.LCC 1 1) Select the number corresponding to the HSYNC cycle to be
(ABOVE+10: DUPLEX MODE) adjusted with 10-key. (Select one of 3.)
2) Press [START] key.
Select 2, and Press [START] key, or
press [START] key. press [CUSTOM SETTINGS] key. Set
Item Default
range
SIMULATION 48-1 0 TRAY SELECT Paper feed tray selection – –
MAGNIFICATION ADJUSTMENT. 1 COPY START Copy START (Default) – –
(MAGNIFICATION) 2 MAGNIFICATION Print magnification ratio 25 - 400 –
INPUT 25-400(%) 100 3 CIS CIS HSYNC cycle 40 - 60 50
(HSYNC cycle adjustment)
1) Select the number corresponding to the HSYNC cycle to be
48-5
adjusted with 10-key. (Select one of 3.)
Purpose Adjustment 2) Press [START] key.
Function Used to adjust the copy magnification ratio in the
3) Enter the HSYNC cycle adjustment value with 10-key.
(Purpose) sub scanning direction.
4) Press [START] key.
Section Optical (Image scanning)
Item Picture quality When the [START] key is pressed, copying is performed and
the adjustment value is set simultaneously.
Operation/Procedure
When the sub scanning direction image magnification ratio adjust- Normal display NOW COPYING.
ment with SIM 48-1 cannot provide a satisfactory result if a differ- ERROR display Door open DOOR OPEN.
ent magnification ration is set and a copy is made, perform this Jam JAM
simulation. Paper empty PAPER EMPTY.
When there is an error in the copy magnification ratio in reduction (Copy condition setting in this simulation)
copy, change the adjustment value of the high speed mode. When
∗ To select paper (paper feed tray), perform the following proce-
there is an error in the copy magnification ratio in enlargement
dures.
copy, change the adjustment value of the low speed mode.
1) Enter 0 with 10-key.
1) Select the number corresponding to the adjustment mode with
2) Press [START] key. (The mode is changed to the paper feed
10-key.
tray selection mode.)
2) Press [START] key.
3) Enter the number corresponding to the paper feed tray of the
3) Enter the copy adjustment value with 10-key.
selected paper with 10-key. (Select one of 1 - 5.)
The scanner/SPF motor rotation sped adjustment value is
4) Press [START] key. (The paper feed tray is selected.)
entered.
1 TRAY1 TRAY1
Set
Item Content Default 2 TRAY2 TRAY2
range
3 TRAY3 TRAY3
0 MIR (220) Mirror motor (220mm/sec) 0 - 99 50
4 TRAY4 TRAY4
1 MIR (169) Mirror motor (168.7mm/sec)
5 BPT Manual feed
2 MIR (110) Mirror motor (110mm/sec)
3 MIR (55) Mirror motor (55mm/sec) When the total of the above set value (1 - 5) and 10 is entered, the
4 SPF (220) SPF motor (220mm/sec) mode is changed to the duplex mode.
5 SPF (110) SPF motor (110mm/sec)
4) Press [START] key. (The paper feed tray is selected.) 1) Enter the number corresponding to the paper feed tray to be
adjusted with 10-key. (Select one of 9 - 14.) (Table 1)
1 TRAY1 TRAY1 2) Press [START] key.
2 TRAY2 TRAY2 3) Enter the adjustment value with 10-key.
3 TRAY3 TRAY3
4) Press [P] key or [START] key. When [START] key is pressed,
4 TRAY4 TRAY4
the adjustment value is set and printing is performed. (Table 2)
5 BPT Manual feed
Check the off-center of the self-print patter of print-out.
∗ To set the magnification ratio, perform the following procedure. (Shift for the adjustment value change: 0.1mm/step)
1) Enter 2 with 10-key. The greater the adjustment value is, the more the print image is
2) Press [START] key. shifted to the front.
3) Enter the copy magnification ratio with 10-key.
(Lead edge void area adjustment)
4) Press [START] key.
1) Set the lead edge void adjustment value (DENA) as specified
Set range 25 - 400 (%) below.
(Standard set value) Paper lead edge void: 3.5mm (DENA:
35)
∗ Set the adjustment value of DENA to 35. Enter 35 as the
adjustment value of DENA, and press [P] key.
Set
0.TRAY SELECT 1
2.MAGNIFICATION 200
1.COPY START 2
Item Default
range (ADJUSTMENT DATA) 3.L4 160 4.L5 160
0 TRAY SELECT Paper feed tray 1-5 –
(IMAGE LOSS SETTING)
selection SIDE1: 5.LEAD_EDGE 15 6.FRONT/REAR 20 7.TRAIL_EDGE 0
1 COPY START Copy START (Default) – – SIDE2: 8.LEAD_EDGE 15 9.FRONT/REAR 20 10.TRAIL_EDGE 0
2 MAGNIFICATION Print magnification 25 - –
Select other than 0 - 2, and press [START] key.
ratio 200% Press [CUSTOM SETTING] key.
(Lead edge adjustment value)
SIMULATION 50-7
3 L4 Distance from the 0 - 999 –
LEAD EDGE ADJUSTMENT(SPF CALC.). INPUT VALUE 0-99, AND
front surface image
PRESS START.
lead edge to the scale 3.L4 50
of 10mm (SPF: 200%)
4 L5 Distance from the – Select 1,
Press [START] key.
back surface image and press Press [CUSTOM SETTINGS] key,
[START] key. or terminate copying.
lead edge to the scale
of 10mm (SPF: 200%) SIMULATION 50-7
(Image loss set value: SIDE 1) LEAD EDGE ADJUSTMENT(SPF CALC.). NOW COPYING.
value
9 FRONT/REAR Back surface side 20 SIMULATION 50-7
edge image loss set LEAD EDGE ADJUSTMENT(SPF CALC.).
value (MAGNIFICATION)
INPUT 25-200(%)
100
10 TRAIL_EDGE Back surface rear 0 - 20 0
edge image loss set
value
50-10
(Table 2)
Purpose Adjustment
Normal display NOW COPYING.
Function Used to adjust the print image off-center position.
ERROR display Door open DOOR OPEN. (Purpose) (Adjusted separately for each paper feed section.)
Jam JAM Item Picture quality Image position
Paper empty PAPER EMPTY.
Operation/Procedure
(Table 3) (Print image off-center position adjustment)
1 TRAY1 TRAY1 NOTE: This simulation cannot provide an accurate adjustment. Do
2 TRAY2 TRAY2 not use.
3 TRAY3 TRAY3 1) Enter the number corresponding to the number of the paper
4 TRAY4 TRAY4 feed tray to be adjusted with 10-key. (Select one of 3 - 9.)
5 BPT Manual feed Item Set range Default
When the total of the above set value and 10 is entered, the mode 0 TRAY SELECT Paper feed tray 1-5 –
is changed to the duplex mode (DD), and a duplex copy is made. selection
1 COPY START Copy START (Default) – –
2 MAGNIFICATION Print magnification 25 - 400% 100
ratio
(Off-center adjustment value)
3 TRAY1 Tray 1 adjustment 0 - 99 50
4 TRAY2 Tray 2 adjustment
5 TRAY3 Tray 3 adjustment
6 TRAY4 Tray 4 adjustment
7 BPT Manual feed tray
adjustment
8 ADU Adjustment when
paper is fed again
from ADU
∗ To select paper (paper feed tray), perform the following proce- SIMULATION 50-10
dures. PRINT OFF-CENTER ADJUSTMENT. NOW COPYING.
1) Enter 0 with 10-key.
2) Press [START] key. (The mode is changed to the paper feed
tray selection mode.)
Select 0, and Press [START] key, or
3) Enter the number corresponding to the paper feed tray to be press [START] key. press [CUSTOM SETTINGS] key.
used with 10-key. (Select one of 1 - 5)
4) Press [START] key. (The paper feed tray is selected.) SIMULATION 50-10
PRINT OFF-CENTER ADJUSTMENT. SELECT 1-15, AND PRESS
1 TRAY1 TRAY1 START.
2 TRAY2 TRAY2
3 TRAY3 TRAY3
(FEED TRAY)
1.TRAY1 2.TRAY2 3.TRAY3 4.TRAY4
1
4 TRAY4 TRAY4 5.BPT
(ABOVE+10: DUPLEX MODE)
5 BPT Manual feed
When the total of the above set value (1 - 5) and 10 is entered, the
mode is changed to the duplex print mode. 50-12
∗ To set the copy magnification ratio, perform the following proce- Purpose Adjustment
dure. Function Used to adjust the scan image off-center position.
1) Enter 2 with 10-key. (Purpose) (Adjusted separately for each scan mode.)
2) Press [START] key. Section
3) Enter the copy magnification ratio with 10-key. Item Picture quality Image position
4) Press [START] key. Operation/Procedure
(Select the scan mode to be adjusted.)
Set range 25 - 400 (%)
1) Enter the number corresponding to the scan mode to be
NOTE: When [P] key is pressed after entering the adjustment adjusted with 10-key. (Select one of 3 - 5.)
value in this simulation, the adjustment value is set. When
[START] key is pressed, the adjustment value is set and Item Set range Default
copying is performed. 0 TRAY SELECT Paper feed tray 1-5 –
selection
1 COPY START Copy START – –
(Default)
2 MAGNIFICATION Print magnification 25 - 400% 100
ratio
(Resist adjustment value)
3 PLATEN OC mode 0 - 99 50
adjustment
4 SPF SIDE1 SPF front surface
adjustment
5 SPF SIDE2 SPF back surface
adjustment
2) Press [START] key.
53 53-7
Purpose Adjustment/Setup/Operation data output/Check
(Display/Print)
53-6
Function Used to enter the SPF width detection adjustment
Purpose Adjustment (Purpose) value.
Function Used to adjust the DSPF width detection level. Section DSPF
(Purpose) Item Operation
Section
Operation/Procedure
Item Operation
1) Enter the number corresponding to the set item with 10-key.
Operation/Procedure
1) Set the SPF paper feed guide to the max. position. Item Set range Default
1 MAX. POSITION Max. width 0 - 1023 66
2) Select "MAX. POSITION" with 10-key.
2 POSITION 1 Adjustment position 1 456
3) Press [START] key.
3 POSITION 2 Adjustment position 2 713
The max. width detection level is recognized.
4 MIN. POSITION Min. width 791
4) Press [CSUTOM SETTING] key.
5) Set the SPF paper feed guide to A4R size position. 2) Press [START] key.
6) Select POSITION 1 with 10-key. 3) Enter the set value with 10key.
7) Press [START] key. 4) Press [START] key.
The A4R width detection level is recognized. SIMULATION 53-7
8) Press [CSUTOM SETTING] key. SPF TRAY ADJUSTMENT(MANUAL). SELECT 1-4, AND PRESS
9) Set the SPF paper feed guide to A5R size position. START.
1.MAX.POSITION: 66
10) Select POSITION 2 with 10-key. 2.POSITION 1 : 456
11) Press [START] key. 3.POSITION 2 : 713 1
The A5R width detection level is recognized. 4.MIN.POSITION: 791
SIMULATION 53-8
SPF SCANNING POSITION ADJUSTMENT. PRESS START. SIMULATION 55-1
1.AUTO ENGINNE SOFT SW. SETTING. INPUT DATA No(1-8), AND PRESS
2.MANUAL. 25 START. 1 2 3 4 5 6 7 8
SOFT SW-1:
00001001
Select 2, and Select 1, and Press
press [START] key. press [START] key. [CUSTOM SETTINGS] key.
55-2
SIMULATION 53-8
SPF SCANNING POSITION ADJUSTMENT EXECUTING.... Purpose Setting
1. AUTO Function Used to set the specifications of the scanner
1 (Purpose) control operations. (Scanner control PWB)
Section
Item Operation Specifications
Normal completion Trouble occurrence
Operation/Procedure
<Normal completion>
This simulation is used to change and check the scanner soft SW.
SIMULATION 53-8 Set this setting to the default.
SPF SCANNING POSITION ADJUSTMENT COMPLETED.
1. AUTO There is no need to change this setting in the market.
1
SIMULATION 55-2
SCANNER SOFT SW. SETTING. SELECT 1-16, AND PRESS START.
<Trouble occurrence>
Operation/Procedure
Used to check if the LSU delivers output of the sync signal SIMULATION 61-2
(HSYNC/) or not. LASER POWER SETTING(COPY). INPUT VALUE 67-150, AND PRESS
"NOW CHECKING" is displayed during checking. When the test is START.
normally completed, "OK" is displayed. If an error occurs, "NG" is 1.AE
93
displayed.
SIMULATION 61-1
LSU TEST. PRESS START. 61-3
1. LSU
1 Purpose
Function
Adjustment
Used to adjust the laser power (absolute value) in
(Purpose) the FAX mode.
Section Scanner (write) unit (LSU)
Press [START] key. Press [CUSTOM SETTINGS] key. Item Operation
Operation/Procedure
SIMULATION 61-1 1) Select the number corresponding to the adjustment mode with
LSU TEST. ···NOW CHECKING
10-key.
1. LSU
2) Press [START] key.
3) Enter the adjustment value with 10-key.
Check completion Press [CUSTOM SETTINGS] key. Set range 67 - 150
Default 76 (AR-M351U/M355U)
93 (AR-M451U/M455U)
SIMULATION 61-1
LSU TEST. ···OK (or NG) 4) Enter [START] key.
1. LSU NOTE: Be sure to set the default value. If not, a trouble may occur
in the LSU.
SIMULATION 61-3
SIMULATION 62-1
LASER POWER SETTING(FAX). INPUT VALUE 67-150, AND PRESS
HDD FORMAT. EXECUTING···.
START.
1.FAX
110 Completion Press [CUSTOM SETTINGS] key.
SIMULATION 62-1
61-4
HDD FORMAT. OK. (or NG)
Purpose Adjustment
Function Used to adjust the laser power (absolute value) in
(Purpose) the printer mode.
62-2
Section Scanner (write) unit (LSU)
Item Operation Purpose Operation test/Check
Operation/Procedure Function Used to check the operation of the hard disk (read/
(Purpose) write). (Only in the model with a disk installed)
1) Select the number corresponding to the adjustment mode with
(Partial check)
10-key.
Section MFP controller (HDD)
2) Press [START] key.
Item Operation
3) Enter the adjustment value with 10-key.
Operation/Procedure
Set range 67-150 1) Select YES/NO of hard disk read/write check.
Default 76 (AR-M351U/M355U)
1 YES Execution
93 (AR-M451U/M455U)
2 NO Cancel
4) Enter [START] key.
2) Press [START] key.
NOTE: Be sure to set the default value. If not, a trouble may occur
in the LSU. During testing, "EXECUTING" is displayed. When test is com-
pleted normally, "OK" is displayed. If not, "NG" is displayed.
SIMULATION 61-4
LASER POWER SETTING(PRINTER). PRESS START. SIMULATION 62-2
1.PRINTER 100 HDD R/W TEST.
SIMULATION 61-4
LASER POWER SETTING(PRINTER). INPUT VALUE 67-150, AND SIMULATION 62-2
PRESS START. HDD R/W TEST. EXECUTING···.
1.PRINTER
100
Completion Press [CUSTOM SETTINGS] key.
SIMULATION 62-2
62 HDD R/W TEST. OK. (or NG)
62-1
Purpose Data clear
Function Used to format the hard disk.
(Purpose) (Only in the model with a disk installed)
o m
Section MFP controller (HDD)
u .c
Item Clear
o
Operation/Procedure
s 4y
1) Select YES/NO of hard disk format. l
ua
an
1 YES Execution
2 NO Cancel
2) Press [START] key.
m
During formatting, "EXECUTING" is displayed. When formatting is
completed normally, "OK" is displayed. If not, "NG" is displayed.
SIMULATION 63-7
63-2 SHADING POSITION ADJUSTMENT. PRESS START.
1. CCD 0
Purpose Adjustment
Function Used to execute shading.
1
(Purpose)
Section Optical (Image scanning) Press [START] key. Press [CUSTOM SETTINGS] key or [START] key.
Item Operation
Operation/Procedure SIMULATION 63-7
1) Enter the number corresponding to the shading mode to be SHADING POSITION ADJUSTMENT. INPUT VALUE 1-16, AND
executed. PRESS START.
SIMULATION 66-1
SIMULATION 65-1
FAX SOFT SW. SETTING. INPUT DATA No(1-8), AND PRESS
START.
1 2 3 4 5 6 7 8
SOFT SW-2:
66-2
Purpose Data clear
65-2
Function Used to clear the FAX soft switch function data
Purpose Adjustment/Setup/Operation data output/Check (Purpose) and to set to the default. (Excluding the
(Display/Print) adjustment values.) (Only when FAX is installed)
Function Used to check the result of the touch panel (LCD Section FAX
(Purpose) display) detection position adjustment. (The Item Data
coordinates are displayed.)
Operation/Procedure
Section Operation (Display/Operation key)
1) Set the destination code with 10-key.
Item
Operation/Procedure Japan 00000000 Finland 00111100
U.S.A. 10110101 Norway 10000010
When the touch panel is touched, the X and Y coordinate values
of the touched point and the coordinate values of the specified Australia 00001001 Denmark 00110001
point are displayed. The coordinate values set with SIM 65-1 are U.K. 10110100 Netherlands 01111011
used as the reference. France 00111101 Italy 01011001
Germany 00000100 Switzerland 10100110
SIMULATION 65-2 400 500 600
Sweden 10100101 Austria 00001010
40
Newzealand 01111110 Indonesia 01010100
100
100
200 300
China 00100110 Thailand 10101001
Singapore 10011100 Malaysia 01101100
140
600 TW 11111110 India 01010011
Other1 11111101 Philippines 10001001
180
200
Other2 11111100 Hongkong 01010000
Ohter3 11111011
The codes other than the above are recognized as Japan.
2) Press [START] key.
66 3) The confirmation menu of YES/NO of clear is displayed.
Select one.
66-1 1 YES FAX soft SW is cleared.
Purpose Setting 2 NO Not cleared.
Function Used to change and check the FAX soft switch 4) Press [START] key.
(Purpose) functions. (Used to change and check the
The soft switch (except for the adjustment values) is cleared
functions provided for the FAX soft switches.)
according to the destination selected in procedure 1).
(Only when FAX is installed)
NOTE: When the FAX BOX is not installed, initialization including
Section FAX
the adjustment value is performed. (The adjustment value
Item
is stored in the FAX BOX.)
Operation/Procedure
Setting of soft switches other than SW1 can be changed and
checked.
1) Enter the soft switch number to be checked or changed with
10-key.
The current set state is displayed.
1:YES
1 FAX PWB MEMORY CHECK
MFP SRAM: CHECKING
2:NO
MFP FLASH: NO CHECK
MFP OP.FLASH: NO CHECK
MODEM EEPROM: NG:A0010000
66-3 MODEM SRAM(G/A):NO CHECK
MODEM SDRAM1: NG A11
Purpose Operation test/Check MODEM SDRAM2: OK
Function Used to check the operation of the FAX PWB
(Purpose) memory (read/write). (This adjustment is required When "repeat" is selected and
[CUSTOM SETTINGS] key is pressed.
when the PWB is replaced with a new one.) (Only
when FAX is installed)
When Check is "once," the display stops at the result display.
Section FAX
When [CUSTOM SETTINGS] key is pressed, the display returns
Item Data to the initial display.
Operation/Procedure
1) Enter the number corresponding to the memory to be checked 66-4
with 10-key.
Purpose Operation test/Check
2) Press [START] key.
Function Used to check the output operation of data signals
In the case of All, all memories are checked only once.
(Purpose) in each data output mode of FAX. (Used to check
Check connection wire list the operation of MODEM. ) Send level: Max. (Only
NO CHECK Not checked yet. when FAX is installed)
CHECKING Checking Section FAX
OK Check complete OK Item Operation
NG Check complete NG Operation/Procedure
The error address or the data line is displayed individually. 1) Enter the number corresponding to the output mode with 10-
key.
Target memory of check
2) Press [START] key.
MFP SRAM SRAM
MFP FLASH FLASH ROM The output is delivered at the max. send level.
MFP OP.FLASH 1 NOSIGNAL No signal 17 12.0 V33 12.0 V33
MODEM EEPROM 2 33.6 V34 26.4 V34 18 14.4 V17 14.4 V17
MODEM SRAM (G/A) 3 31.2 V34 31.2 V34 19 12.0 V17 12.0 V17
MODEM SDRAM1 4 28.8 V34 28.8 V34 20 9.6 V17 9.6 V17
MODEM SDRAM2 5 26.4 V34 26.4 V34 21 7.2 V17 7.2 V17
When "repeat" is selected, the operation is repeated until the 6 24.0 V34 24.0 V34 22 9.6 V29 9.6 V29
result is "NG" or [CUSTOMSETTING" is pressed. 7 21.6 V34 21.6 V34 23 7.2 V29 7.2 V29
8 19.2 V34 19.2 V34 24 4.8 V27t 4.8 V27t
9 16.8 V34 16.8 V34 25 2.4 V27t 2.4 V27t
10 14.4 V34 14.4 V34 26 0.3 FLG 0.3 FLG
11 12.0 V34 12.0 V34 27 CED 2100 CED 2100
12 9.6 V34 9.6 V34 28 CNG 1100 CNG 1100
13 7.2 V34 7.2 V34 29 0.3 V21 0.3 V21
14 4.8 V34 4.8 V34 30 ANSam ANSam
15 2.4 V34 2.4 V34 31 RINGER RINGER
16 14.4 V33 14.4 V33 32 No RBT No RBT
When [CUSTOM SETTINGS] key is pressed during execution,
execution is stopped.
When a number is entered and [START] key is pressed during
execution, the kind of signal can be changed.
SIMULATION 66-5
SIGNAL OUTPUT CHECK.(SOFT SW.) SELECT 1-32, AND PRESS
66-5 START. EXECUTING···.
Operation/Procedure
1) Enter the number corresponding to the output mode with 10- SIMULATION 66-5
key. SIGNAL OUTPUT CHECK.(SOFT SW.) SELECT 1-32, AND PRESS
START.
2) Press [START] key.
The output is delivered at the send level set with the soft switch.
1.NOSIGNAL
2.26.4 V34
2.33.6 V34
6.24.0 V34
3.31.2 V34
7.21.6 V34
4.28.8 V34
8.19.2 V34
2
9.16.8 V34 10.14.4 V34 11.12.0 V34 12.9.6 V34
13.7.2 V34 14.4.8 V34 15.2.4 V34 16.14.4 V33
17.12.0 V33 18.14.4 V17 19.12.0 V17 20.9.6 V17
21.7.2 V17 22.9.6 V29 23.7.2 V29 24.4.8 V27t
25.2.4 V27t 26.0.3 FLG 27.CED 2100 28.CNG 1100
29.0.3 V21 30.ANSam 31.RINGER 32.No RBT
SIMULATION 66-8
66-7
MESSAGE OUTPUT CHECK.(LEVEL MAX) SELECT 1-20, AND PRESS
Purpose User data output/Check (Display/Print) START.
1.NONE 2.PAUSE 3.MESSAGE1
Function Used to print the image memory data (memory 4.MESSAGE2 5.MESSAGE3 6.MESSAGE4
(Purpose) send/receive). (Only when FAX is installed) 7.MESSAGE5 8.MESSAGE6 9.MESSAGE7 2
Section FAX 10.MESSAGE8 11.MESSAGE9 12.MESSAGE10
13.MESSAGE11 14.MESSAGE12 15.MESSAGE13
Item Data 16.MESSAGE14 17.MESSAGE15 18.ALARM
Operation/Procedure 19.RINGER 20.EXT.TEL.RINGER
All image data stored in the image memory are printed. Select other 1, and press [START] key.
Press [CUSTOM SETTINGS] key.
∗ The confidential receive data are also printed.
SIMULATION 66-8
1 PRINT START Print start MESSAGE OUTPUT CHECK.(LEVEL MAX) SELECT 1-20, AND PRESS
START. EXECUTING···.
The paper is automatically selected with the size saved in the 1.NONE 2.PAUSE 3.MESSAGE1
image memory. 4.MESSAGE2 5.MESSAGE3 6.MESSAGE4
7.MESSAGE5
10.MESSAGE8
8.MESSAGE6
11.MESSAGE9
9.MESSAGE7
12.MESSAGE10
1
SIMULATION 66-7
13.MESSAGE11 14.MESSAGE12 15.MESSAGE13
IMAGE MEMORY PRINT OUT. PRESS START. Same 16.MESSAGE14 17.MESSAGE15 18.ALARM
1.PRINT START display 19.RINGER 20.EXT.TEL.RINGER
SIMULATION 66-8
MESSAGE OUTPUT CHECK.(LEVEL MAX) SELECT 1-20, AND PRESS
START.
1.NONE 2.PAUSE 3.MESSAGE1
4.MESSAGE2 5.MESSAGE3 6.MESSAGE4
7.MESSAGE5
10.MESSAGE8
8.MESSAGE6
11.MESSAGE9
9.MESSAGE7
12.MESSAGE10
2
13.MESSAGE11 14.MESSAGE12 15.MESSAGE13
16.MESSAGE14 17.MESSAGE15 18.ALARM
19.RINGER 20.EXT.TEL.RINGER
SIMULATION 66-11
300bps SIGNAL OUTPUT.(LEVEL MAX) SELECT 1-6, AND PRESS SIMULATION 66-12
START. 300bps SIGNAL OUTPUT.(SOFT SW.) SELECT 1-6, AND PRESS
EXECUTING···. START.
1. NO SIGNAL 2. 11111 3. 11110 4. 00000 1 EXECUTING···.
5. 010101 6. 00001 1. NO SIGNAL 2. 11111 3. 11110 4. 00000 1
5. 010101 6. 00001
Same display Select 3 and press [START] key.
Same display Select 3 and press [START] key.
SIMULATION 66-11
300bps SIGNAL OUTPUT.(LEVEL MAX) SELECT 1-6, AND PRESS SIMULATION 66-12
START. 300bps SIGNAL OUTPUT.(SOFT SW.) SELECT 1-6, AND PRESS
EXECUTING···. START.
1. NO SIGNAL 2. 11111 3. 11110 4. 00000 3 EXECUTING···.
5. 010101 6. 00001 1. NO SIGNAL 2. 11111 3. 11110 4. 00000 2
5. 010101 6. 00001
Press [CUSTOM SETTINGS] key.
Press [CUSTOM SETTINGS] key.
66-12
66-13
Purpose Operation test/Check
Function Used to check the output operation of FAX G3 Purpose Setting
(Purpose) mode 300bps. (Used to check the operation of Function Used to enter (set) the number of FAX dial signal
MODEM.) An output is send at the send level set (Purpose) output test. (The dial number set by this simulation
by the soft switch. (Only when FAX is installed) is outputted when the dial signal output test is
Section FAX made by SIM 66-14 - 16. ) (Only when FAX is
Item Operation installed)
Operation/Procedure Section FAX
Item Data
1) Select the number corresponding to the output mode with 10-
key. Operation/Procedure
2) Press [START] key. 1) Enter the dial number with 10-key.
The signal is sent in the send level set with the soft switch. Use 10-key, [*] key, and [#] key to enter the number. The
upper limit is 20 digits.
1 NO SIGNAL No signal 4 00000 00000
When [CLEAR] key is pressed, the mode returns to the initial
2 11111 11111 5 010101 010101
state.
3 11110 11110 6 00001 00001
2) Press [START] key.
When the number is entered during execution, the kind of signal
can be changed. SIMULATION 66-13
When [CUSTOM SETTINGS] key is pressed during execution, the DIAL TEST NUMBER SETTING. 0-9:[0-9], *:[*], #:[#]
operation is stopped. INPUT NUMBER AND PRESS START.
0123456789*#01234567
66-14
Purpose Setting/Operation test/Check
Function Used to set the make time in the FAX pulse dial
(Purpose) mode (10pps) and to test the dial signal output.
(The dial number signal set by SIM 66-13 is
outputted.) Used to check troubles in dialing and
to check the operation. (Only when FAX is
installed)
Section FAX
Item Operation
Operation/Procedure
1) Enter 0 with 10-key.
2) Press [START] key.
The dial signal is outputted.
SIMULATION 66-14
DIAL TEST(10PPS). SELECT 0-15, AND PRESS START. 66-16
[1. MAKE TIME]
7 Purpose Setting/Operation test/Check
Function Used to check the dial signal (DTMF) output in the
(Purpose) FAX tone dial mode. (The dial number signal set
Press [CUSTOM SETTINGS] key.
by SIM 66-13 is outputted.) The send level can be
set to an optional level. Used to check troubles in
SIMULATION 66-14 dialing and to check the operation. (Only when
DIAL TEST(10PPS). EXECUTE
FAX is installed)
1. MAKE TIME 7 ; [+29 ms]
Section FAX
Item Operation
Operation/Procedure
66-15 1) Enter 0 with 10-key.
Purpose Setting/Operation test/Check 2) Press [START] key.
Function Used to set the make time in the FAX pulse dial The dial signal is outputted.
(Purpose) mode (20pps) and to test the dial signal output.
(The dial number signal set by SIM 66-13 is
(Dial pulse make time setting)
outputted.) Used to check troubles in dialing and
to check the operation. (Only when FAX is 1) Enter 1 or 2 with 10-key.
installed) 2) Press [START] key.
Section FAX 3) Enter the set value with 10-key.
Item Operation 4) Press [START] key.
Operation/Procedure Item Set range
1) Enter 0 with 10-key. 0 EXECUTE Execution
2) Press [START] key. 1 HIGH High group level 0 - 15dB
The dial signal is outputted. 2 HIGH LOW High group - Low group 0 - 15
(Dial pulse make time setting) When [CUSTOM SETTINGS] key is pressed during execution, the
1) Enter 1 with 10-key. operation is stopped.
2) Press [START] key.
3) Enter the set value with 10-key.
4) Press [START] key.
0 EXECUTE Execute
1 MAKE TIME Dial pulse make time setting (0 - 15)
The dial signal is sent with the set value + 9ms.
When [CUSTOM SETTINGS] key is pressed during execution, the
operation is stopped.
SIMULATION 66-16
DIAL TEST(DTMF). SELECT 0-15, AND PRESS START. Press [START] key. Press [CUSTOM SETTINGS] key.
1. HIGH(dB) 7
SIMULATION 66-18
(When 2)
DTMF SIGNAL OUTPUT.(SOFT SW.) EXECUTING···.
SIMULATION 66-16
DIAL TEST(DTMF). SELECT 0-15, AND PRESS START.
1
1. HIGH(dB) 7
Select 0 and press [START] key. Press [CUSTOM SETTINGS] key. 66-19
(When 0)
Purpose Data transfer
SIMULATION 66-16 Function Used to back-up the HDD data into the Flash
DIAL TEST(DTMF). EXECUTING···.
(Purpose) memory (optional FAX expansion memory: AR-
1. HIGH 7 (dB) 2. HIGH-LOW 7
MM9). (Only when FAX is installed)
Section FAX
Item Data
66-17 Operation/Procedure
Purpose Setting 1) Select YES/NO of data transfer (backup).
Function Used to check the dial signal (DTMF) output in the 1 YES Backup is executed.
(Purpose) FAX tone dial mode. Send level: Max. Used to 2 NO Backup is not executed.
check the operation. (Only when FAX is installed)
2) Press [START] key.
Section FAX
Item Operation This function is valid only when the AR-MM9 is installed.
SIMULATION 66-19
ADDRESS DATA BACK UP. (WRITE TO FLASH ROM) EXECUTING...
66-18
Purpose Setting 1
Function Used to check the dial signal (DTMF) output in the
(Purpose) FAX tone dial mode. An output is sent at the send After completion of backup
level set by the soft switch. Used to check the
operation. (Only when FAX is installed)
Section FAX
Item Operation
Operation/Procedure
1) Enter the DTMF signal (1 - 9, 0, *, #) to be sent with 10-key.
2) Press [START] key.
1. MIN
Press [START] key.
2. MIDDLE
3. MAX
2
SIMULATION 66-20
ADDRESS DATA BACK UP. (READ FROM FLASH ROM) EXECUTING... Press [START] key.
Press [CUSTOM SETTINGS] key.
1 SIMULATION 66-22
HANDSET VOLUME SETTING SELECT 1-3, AND PRESS START.
EXECUTING···.
After completion of read
1. MIN
2. MIDDLE
3. MAX
2
66-21
Same display Select 3 and press [START] key.
Purpose Adjustment/Setup/Operation data output/Check
(Display/Print)
Function Used to print information related to FAX (various SIMULATION 66-22
(Purpose) registrations, communication management, file HANDSET VOLUME SETTING SELECT 1-3, AND PRESS START.
management, system error protocol). (Only when EXECUTING···.
FAX is installed) 1. MIN
Section FAX
2. MIDDLE
3. MAX
3
Item Data
Operation/Procedure Press [CUSTOM SETTINGS] key.
0. NO DESTINATION 1
1. JAPAN
SIMULATION 66-35
2. U.S.A./CANADA
MODEM PROGRAM RELOAD.
3. EUROPE
LOADER···OK
4. AUSTRALIA
MODEM····COMPLETE
5. CHINA
6. ASIA
SIMULATION 66-42
SIMULATION 66-36
PIC PROGRAM RELOAD
MFPC-MDMC I/F CHECK. INPUT 1-8, AND PRESS START.
EXECUTING...(OK or NG) OK
5) Select 0.
1.ci_level_judge(1-15) 2
6) The confirmation window is displayed. Select whether the PIC Select 0
and press Press [CUSTOM SETTINGS] key
adjustment values are written or not. [START] key. or select 2.
SIMULATION 67-2
CENTRO PORT CHECK.
CENTRO PORT: OK (or STAGE7 NG)
67-11
Purpose Setting
Function Used to set YES/NO of the parallel I/F select
(Purpose) signal of the printer.
Section MFP controller
Item Operation Interface/Communication
Operation/Procedure
1) Enter the number corresponding to the select IN signal YES/
NO setting with 10-key.
Item Default
0 OFF 1
1 ON
2) Press [START] key.
When the printer parallel I/F is used and a trouble is generated in
the communication between the PC and the printer, change the
setting of this simulation.
SIMULATION 67-11
CENTRO SELECT IN SIGNAL SETTING. SELECT 0-1, AND PRESS
START.
0. OFF
1. ON
ENGINE SCANNER
CONTROLLER CONTROLLER
1. Acceptable originals
Hole positions
A stack of up to 50 original sheets (30 original sheets*1 for 8-1/2" x
14" (B4) or larger) of the same size paper can be set in the docu-
ment feeder tray provided the stack height is within the limit shown
below. Hole
positions
A stack of up to 30 mixed size originals can be set if the width of
the originals is the same and the stack height is within the limit
shown below. In this case, however, stapling and duplex will not Hole positions
function and some special functions may not give the expected
result.
*1: For paper heavier than 28 lbs. (105g/m2), only a stack of up to
15 sheets can be set. Setting 16 or more sheets may cause
incorrect scanning of original and scanned image may
2. Standard original placement
become expanded compared with original itself. orientations
A. Size and weight of acceptable originals Place originals in the document feeder tray or on the document
glass so that the top and bottom of the original is positioned as
5-1/2" x 8-1/2" shown in the illustration. If not, staples will be incorrectly posi-
or A5 tioned and some special features may not give the expected
Original size: 11" x 17"
or A3 result.
Top Top
14 lbs. or 50g/m 2 34 lbs. or 128g/m 2
<Notes on use of the automatic document feeder> 3. Automatic copy image rotation -
• Use originals within the specified size and weight ranges. Use of
originals out of the specified range may cause an original mis-
rotation copying
feed. If the orientation of the originals and copy paper are different, the
• Before loading originals into the document feeder tray, be sure original image will be automatically rotated 90° and copied. (When
to remove any staples or paper clips. an image is rotated, a message will be displayed.) If a function is
• If originals have damp spots from correction fluid, ink or glue selected that is not suitable for rotation, such as enlarging the
from pasteups, be sure they are dried before they are fed. If not, copy to greater than 8-1/2" x 11" (A4) size or staple sorting with
the interior of the document feeder or the document glass may the saddle stitch finisher, rotation will not be possible.
be soiled.
[Example]
• Do not use the following originals. These originals may cause
incorrect original size detection, original misfeeds, and smudges Orientation of original Orientation of paper Copy after rotation
on copies.
Transparency film, tracing paper, carbon paper, thermal paper
or originals printed with thermal transfer ink ribbon should not be
fed through the document feeder. Originals to be fed through
the feeder should not be damaged, crumpled or folded or have
loosely pasted paper on them or cutouts in them. Originals with
multiple punched holes other than two-hole or three-hole
Face down Face down
punched paper may not feed correctly.
5. Printing onto envelopes 2) Lower the two fusing unit pressure adjusting levers marked A
and B in the illustration.
• Do not use envelopes that have metal clasps, plastic snaps,
string closures, windows, linings, self-adhesive patches or syn- A
thetic materials. Attempting to print on these may cause mis- B
feeds, inadequate toner adherence or other trouble.
• Creases or smudging may occur. This is especially true of
embossed surfaces and other irregular surfaces.
• Under high humidity and temperature conditions the glue flaps
on some envelopes may become sticky and be sealed closed
when printed.
Normal position
• Use only envelopes which are flat and crisply folded. Curled or
poorly formed envelopes may be poorly printed or may cause
misfeeds.
y ou.c om
nu a l s 4
ma
Version Check
(2) Update procedures
CONF: ********* 1) When the machine is booted, the following window is dis-
played.
2) Press MENU key a few times to display the following window.
(In addition, when File2PRN.EXE is used, select the connec- Version Check
tion type (USB or parallel) with the Up/Down select key.) CONF: *********
Firm Update 2) Press MENU key a few times to display the following window.
From Parallel (In addition, when File2PRN.EXE is used, press Up/Down key
to select the connection type (USB or parallel).)
3) Press OK key, and the following window is displayed.
CN Update
Firm Update From Parallel
Waiting Data
3) Press OK key, and the following window is displayed.
4) When files are transferred from the PC by Fcopy.EXE or
File2PRN.EXE (collective files or a separate file for each CN Update
ROM), the LED flashes and the display is changed sequen- Waiting Data
tially as shown below. When the scanner is updated, the back-
4) When files are transferred from the PC by the use of
light of the LCD is instantaneously turned off. Since it is not a
Fcopy.EXE or File2PRN.EXE, the data LED flashes and the
breakdown, do not turn off the power but wait for a while.
window is changed sequentially as follows. The LED finishes
When “Result: OK” is displayed after completion of writing
flashing in a few minutes, and “Writing: OK” is displayed.
(several minutes), press Up/Down key to check that there is
no “Result: NG” for each ROM. (When, however, the collective CN Update
files are updated with the machine which has no FAX installed, Receiving Data
“Result: NG” is displayed for FAX.) When “Result: NG” is dis-
played, refer to (D.). 5) Press OK key, and the following window is displayed.
↓ 6) Use Up/Down key to select the slot No. to which the ROM is
Firm Update inserted, and press OK key. The LED flashes and the window
is changed sequentially as shown below. After completion of
Writing Data
writing (several minutes), check to confirm that “Result: OK” is
↓ displayed.
Firm Update ***
CN Update ***-> CN6
Result: OK
Writing Data
5) Reboot the machine, and use Up/Down key on the window of ↓
1) to check to confirm that the version of the updated software
CN Update ***-> CN6
has been updated.
Result: OK
6) Turn off the power, and reset the DIP switches to the upper
side (normal side). 7) After turning off the power, replace the ROM to which writing is
made with the ROM of the specified slot of the PWB, and turn
on the power and check the operation and the version. (Use
Up/Down key to check on the window of 1).)
8) Turn off the power, and reset the DIP switches to the upper
side (protect side, normal side).
Version Check
CONF: *********
At that time, use Up/Down key to check the version of the PCU or
the scanner. If the version is displayed as “BootMode,” or if the
key operation is invalid (all the LED’s are flashing), retry updating
as follows.
1) When the key operation is possible and the version is dis-
played as “BootMode”
Turn off the power and retry the update procedure of (B.). At
that time, be sure to set the DIP switches properly. After
updating again, if the result is still NG, replace the ROM’s with
the spare one of the PCU and the scanner ROM, and perform
the update procedure of (C.) for the replaced ROM's.
2) When the key operation is invalid
Turn off the power and replace the ROM’s with the spare one
of the PCU and the scanner ROM, and perform the update
procedure of (C.) for the replaced ROM’s. Be sure to set the
DIP switches properly.
YES
Result: OK ?
YES
Result: OK ?
NO Update completed
ROM trouble?
Replace the ROM and retry.
NO YES
Rebootable?
YES
Result: OK ?
YES
Result: OK ?
NO Update completed
ROM trouble?
Replace the ROM and retry.
PANEL
STMP DSW-D ADUSET VFM1
CCFT (OPTION) DEVELOPER un DSW-F
MPFS MPFC VFM1 TCS
DSPFun [EF3]/SPFun [EF4] COIN VENDER
SCN JNT PWB MPWS MPED DSW-L
(OPTION) HUS-DV
MSS MPLD1 DVCH CFM2
CISun CIScnt PWB PNC
AR-MU2
* DSPF un(AR-EF3) only: CIS un, CIScnt PWB AUDITOR MPLS1 MPLS2 VFM2
(OPTION) (OPTION)
SCNcnt MPFSET
SPFM PWB ENGINE LEFT DOOR un
[13] ELECTRICAL SECTION
SCN GND2
(NC)
+12V1
16
17
18
16
17
18
+24V3 19 19
JNT +24V3
PDSEL1
PDSEL2
20
21
22
20
21
22
/KEYIN 23 23
SEG0 24 24
PWB GND2
GND2
25
26
25
26
(1/2) LcdS+ 27 27
LcdS- 28 28
LcdM+ 29 29
LcdM- 30 30
LcdCP1+ 31 31
CN1 CN1 LcdCP1- 32 32
IL-FPR-40S-VF-E1500 IL-FPR-40S-VF-E1500 LcdCP2+ 33
33
CN201 GND2 1 40 GND2
BM12B-SRSS-TB LcdCP2- 34 34
GND2 2 39 GND2 LcdD0+ 35 35
1 IMG_DOUT1_0 GND2 3 38 GND2 LcdD0- 36 36
2 IMG_DOUT1_1 GND2 4 37 GND2 LcdD1+ 37 37
3 IMG_DOUT1_2 1_DATA1+ 5 36 1_DATA1+ LcdD1- 38 38
4 IMG_DOUT1_3 1_DATA1- 6 35 1_DATA1- LcdD2+ 39 39
5 IMG_DOUT1_4 GND2 7 34 GND2 LcdD2- 40 40
6 IMG_DOUT1_5 1_DATA0+ 8 33 1_DATA0+ LcdD3+ 41 41
7 IMG_DOUT1_6 1_DATA0- 9 32 1_DATA0- LcdD3- 42 42
8 IMG_DOUT1_7 GND2 10 31 GND2 GND2 43 43
9 IMG_AREA1 DCLK+ 11 30 1_CLK+ GND2 44 44
10 GND2 DCLK- 12 29 1_CLK- YH 45 45
11 AD_CLK GND2 13 28 GND2 /XL 46 46
12 GND2 /1_DBL+ 14 27 /1_DBL+ /STSET 47 47
/1_DBL- 15 26 /1_DBL- /STMPS 48 48
GND2 16 25 GND2 GND2 49 49
FRM_CCD1 17 24 FRM_CCD1 GND2 50 50
PAGE1 18 23 PAGE1 GND2 51 51
CLK_CCD1 19 22 CLK_CCD1 GND2 52 52
ADD_CCD1 20 21 ADD_CCD1 +12V1 53 53
CCD TXD_CCD1
RXD_CCD1
RES_CCD1
21
22
23
20 TXD_CCD1
19 RXD_CCD1
18 RES_CCD1
+12V1
GND2
54
55
54
55
+5V2 56 56
GND2 24 17 GND2 GND2 57 57
cnt +3.3V3
+3.3V3
GND2
25
26
27
16 +3.3V3
15 +3.3V3
14 GND2
+5V2
GND2
58
59
58
59
+3.3V 60 60
+5VCCD 28 13 +5VCCD FRM_CCD1 61 61
PWB +5VCCD
+5VCCD
+5VCCD
29
30
31
12 +5VCCD
11 +5VCCD
10 +5VCCD
CLK_CCD1 62
TXD_CCD1 63
RES_CCD1 64
62
63
64
+5VCCD 32 9 +5VCCD RXD_CCD1 65 65
+5VCCD 33 8 +5VCCD ADD_CCD1 66 66
+5VCCD 34 7 +5VCCD GND2 67 67
+5VCCD 35 6 +5VCCD PAGE1 68 68
GND2 36 5 GND2 GND2 69 69
+10V 37 4 +10VCCD GND2 70 70
+10V 38 3 +10VCCD /CL1 71 71
GND2 39 2 GND2 PDSEL0 72 72
GND2 40 1 GND2 +5V2 73 73
PD 74 74
SEG1 75 75
SEG2 76 76
GND2 77 77
/F0 78 78
GND2 79 79
/F1 80 80
GND2 81 81
/F2 82 82
GND2 83 83
/F3 84 84
GND2 85 85
/BZR 86 86
GND2 87 87
+5V1 88 88
Lcd DIS 89 89
+3.3V 90 90
GND2 91 91
LCD-VEE 92 92
TH 93 93
/CCFT 94 94
/YL 95 95
XH 96 96
+24V3 97 97
+24V3 98 98
GND2 99 99
GND2 100 100
GND2
33
49
43
24
44
/2_DBL-
/RES_SCN
GND2
31 LcdCP1+
LcdD0+ 18 11 LcdD0+
32 LcdCP1-
33 LcdCP2+
34 LcdCP2- PWB LcdD0-
LcdD1+
LcdD1-
16
14
12
45
12
46
LcdD0-
LcdD1+
LcdD1-
35 LcdD0+
36 LcdD0- (1/3) LcdD2+ 10 13 LcdD2+
LcdD2- 8 47 LcdD2-
37 LcdD1+
LcdD3+ 6 14 LcdD3+
38 LcdD1-
39 LcdD2+
40 LcdD2-
LcdD3-
LcdM+
LcdM-
4
30
28
48
15
49
LcdD3-
LcdM+
LcdM-
MFP
41 LcdD3+
LcdS+ 34 16 LcdS+
42 LcdD3-
LcdS- 32 50 LcdS-
43 GND2
44 GND2
LcdCP1+
LcdCP1-
26
24
17
51
LcdCP1+
LcdCP1-
cnt
45 YH
LcdCP2+ 22 18 LcdCP2+
46 /XL
LcdCP2- 20 52 LcdCP2-
47 /STSET
48 /STMPS
49 GND2
GND2
SLEEP
38
44
10
53
GND2
SLEEP
PWB
LCD_VEE 48 20 LCD_VEE
50 GND2
SCN_SET 46 54 SCN_SET
51 GND2
WAKE_UP 40
52 GND2
GND2 19
53 +12V1
FRDY 42
54 +12V1
55 GND2
56 +5V2 CN3
BM30B-SRDS-G-TF
57 GND2
/RES_SCN 24
58 +5V2
VCCW_SCN 26 21 VCCW_SCN
59 GND2
55 WAKE_UP
60 +3.3V
/RXD_SCN 27 22 /RXD_SCN
61 FRM_CCD1
/TXD_SCN 23 56 /TXD_SCN
62 CLK_CCD1
/DSR_SCN 25 23 /DSR_SCN
63 TXD_CCD1
/DTR_SCN 21 57 /DTR_SCN
64 RES_CCD1
GND2 14 27 GND2
65 RXD_CCD1
POF_SCN 28 58 POF_SCN
66 ADD_CCD1
/RES_MFP 19 25 /RES_MFP
67 GND2
GND2 22 59 GND2
68 PAGE1
+12V1 16 26 +12V1
69 GND2
5 GND2
70 GND2
+12V1 15 60 +12V1
71 /CL1
GND2 13 61 GND2
72 PDSEL0
+5V2 12 28 +5V2
73 +5V2
+5V2 11 62 +5V2
74 PD
+5V2 10 29 +5V2
75 SEG1
+5V2 9 63 +5V2
76 SEG2
+5V1 20 30 +5V1
77 GND2
GND2 18 31 GND2
78 /F0
64 FRDY
79 GND2
GND2 17 65 GND2
80 /F1
+24V3 5 32 +24V3
81 GND2
GND2 7 34 GND2
82 /F2
+24V3 3 33 +24V3
83 GND2
GND2 8 67 GND2
84 /F3
+24V3 4 66 +24V3
85 GND2
GND2 6 68 GND2
86 /BZR
GND2 1
87 GND2
GND2 2
88 +5V1
GND2 29
89 Lcd DIS
GND2 30
90 +3.3V
91 GND2
92 LCD-VEE
93 TH
94 /CCFT
95 /YL
96 XH
97 +24V3
98 +24V3
99 GND2
100 GND2
CN4
20FLS-SM1-TB
GND2 20 1 GND2
(NC) 19 2 (NC)
CN1 CN5
(NC) 18 3 (NC) 30FMZ-BT 30FMN-BT
(NC) 17 4 (NC) XH 30 1 XH
(NC) 16 5 (NC) /YL 29 2 /YL
GND2 15 6 GND2 /XL 28 3 /XL
LCD D3 14 7 LCD D3 YH 27 4 YH
LCD D2 13 8 LCD D2 /CCFT 26 5 /CCFT
LCD D1 12 9 LCD D1 +24V3 25 6 +24V3
LCD LCD D0 11 10 LCD D0 GND2 24 7 GND2
GND2 10 11 GND2 TH 23 8 TH
LCD-VEE 9 12 LCD-VEE
3.3V 13 3.3V
LVDS GND2 22 9 GND2
8 LcdD3- 21 10 LcdD3-
Lcd DIS 7 14 Lcd DIS LcdD3+ 20 11 LcdD3+
GND2 6 15 GND2
PWB LcdD2- 19 12 LcdD2-
LCD CP2 5 16 LCD CP2 LcdD2+ 18 13 LcdD2+
GND2 4 17 GND2 LcdD1- 17 14 LcdD1-
LCD CP1 3 18 LCD CP1 LcdD1+ 16 15 LcdD1+
LCD M 2 19 LCD M LcdD0- 15 16 LcdD0-
LCD S 1 20 LCD S LcdD0+ 14 17 LcdD0+
LCD-VEE 13 18 LCD-VEE
3.3V 12 19 3.3V
CN2 LcdDIS 11 20 LcdDIS
FFC-4PIN 04FM-1.0ST GND2 10 21 GND2
(X2) 1 /YL
TOUCH (Y2) 2 XH
LcdCP2- 9 22 LcdCP2-
LcdCP2+ 8 23 LcdCP2+
(X1) 3 YH
PANEL (Y1) 4 /XL
GND2 7 24 GND2
LcdCP1- 6 25 LcdCP1-
LcdCP1+ 5 26 LcdCP1+
LcdM- 4 27 LcdM-
CN3
CCFT /CCFT
HV
1
2
S02(8.0)B-BHS-L
1 /CCFT
2 HV
LcdM+
LcdS-
LcdS+
3
2
1
28
29
30
LcdM+
LcdS-
LcdS+
SCN
CN101 CN4
JNT
T24FAZ-SMT-TF T24FAZ-SMT-TF
GND2 24 1 GND2
PDSEL0
S6B-PH-K-S
1
BR
CN102
B6B-PH-SM3-TB
1 PDSEL0
PDSEL0
PDSEL1
23
22
2 PDSEL0
3 PDSEL1
PWB
PDSEL1 2
LB
2 PDSEL1 PDSEL2 21 4 PDSEL2 (2/2)
PL +5V2 20 5 +5V2
PDSEL2 3 PDSEL2
ORS PD 3
BL
4 +5V2 PD 19 6 PD
+5V2 4
BR GND2 18 7 GND2
PD 5 5 PD
GY +5V2 17 8 +5V2
GND2 6 6 GND2
/KEYIN 16 9 /KEYIN
SEG0 15 10 SEG0
MFP SEG1 14 11 SEG1
OPE SEG2 13 12 SEG2
/F0 12 13 /F0
/F1 11 14 /F1
PWB /F2 10 15 /F2
/F3 9 16 /F3
GND2 8 17 GND2
GND2 7 18 GND2
GND2 6 19 GND2
(NC) 5 20 (NC)
(NC) 4 21 (NC)
/BZR 3 22 /BZR
+5V1 2 23 +5V1
GND2 1 24 GND2
CN1 CN2
SLD5R-1 SLD5S-1
GND2 5 1 GND2
GND2 4 2 GND2
CL1 /CL1 3 3 /CL1
+24V3 2 4 +24V3
+24V3 1 5 +24V3
CN6
179228-4+175694-4 B4B-PH-K-S
RD
+24V3 1 1 +24V3
BR
/STMPS 2 2 /STMPS
STMP /STSET 3
LB
3 /STSET
GY
GND2 4 4 GND2
CN5
B8B-PH-K-S
GND2 1
/RES_MFP 2
/DSR_SCN 3
/RXD_SCN 4
/TXD_SCN 5
DTR_SCN 6
+5V2 7
(NC) 8
CN6
S6B-PH-K-S H3P-SHF-AA+B3P-SHF-1AA
BL BL
+5V1 1 1 +5V1
GY GY
GND2 2
LB LB
2 GND2 OCSW
OCSW 3 3 OCSW
RD
+24V3 4
BR RD
N SCN /LED0
/LED1
5
6
LB BR
LB
ORS
LED
cnt CN8
1-171825-2
+24V3 1
B PWB GND2
/CV_COPY
2
3
/CV_COUNT 4
(2/3) /CV_START 5
/CV_CA 6
/CV_STAPLE 7
/CV_DUPLEX 8
/CV_SIZE0 9
/CV_SIZE1 10
/CV_SIZE2 11
/CV_SIZE3 12
CN9
B13B-PH-K-S PHR-13
/PNC 1 1
/COPY 2 2
/CA 3 3
/READY 4 4
/AUD 5 5
+5V2 6 6
GND2 7 7
+24V3 8 8
(NC) 9 9
/TC 10 10
+24V3 11 11
PNC_a 12 12
GND2 13 13
CN11
S3B-PH-K-S 53053-0310(MOLEX)
LB
MHPS 1 1 MHPS
GY
GND2 2
BL
2 GND2 MHPS
+5V2 3 3 +5V2
CND CNC
PHNR-6-H+BU6P-TR-P-H B26B-PHDSS-B
B6B-PH-K-S
BR BR BR +24V3 RD
6 /B 1 2 /B 7
RD RD RD RD
5 +24V3 2 4 +24V3 +24V3 8
SPF PL 4 B 3 PL PL 1 B GND2 5
GY
BR BR BR GY
3 A 4 3 A GND2 6
MOTOR RD 2 +24V3 5 RD RD 5 +24V3
PL PL PL BL
1 /A 6 6 /A +5V2 4
GY
GND2 9
1754873+179228-3 BL
VAREF 17
BL BR
+5V1 1 SPPD 19
BR BR
SPED SPED 2
GY
SPFC 18
GND2 3 SPED 21
BR
1754873+179228-3 SDSS 12
BL CNB BR
+5V2 PHNR-11-H+BU11P-TR-P-H SCOV 23
1 B22B-PHDSS-B PL
PL BL BL SRRC 14
SCOV SCOV 2
GY BR
1 +5V1 11
BR
5 +5V
SPWS 24
BR
GND2 3 2 SPED 10 16 SPED PL
GY GY SPFS 16
1754873+179228-3 3 GND2 9 1 GND2
BL BL BL
BL 4 +5V2 8 7 +5V2
+5V2 1 PL PL PL
BR 5 SCOV 7 18 SCOV
SPPD SPPD 2
GY GY
6 GND2 6
GY GY
GND2 SPFMO0 3
PL
GND2 3 2 PL
BL BL BL SPOD 25
7 +5V2 5 8 +5V2 PL
BR BR BR /SPFMA 2
8 SPPD 4 14 SPPD PL
SMP-02V-NC+SMR-02V-N GY GY GY SOCD 26
9 GND2 3 3 GND2 BR
RD RD RD RD SPFMA 1
1 +24V3 1 10 +24V3 2 11 +24V3 BR
SDSS 2 /SDSS 2
BR BR
11 /SDSS 1
BR BR
15 /SDSS SPLS1 22
BL BR
9 +5VPOD /SPFMB 11
GY PL
4 GND2 SPLS2 20
PL PL
20 SPOD SPFMB 13
B3B-PH-K-S PHNR-6-H+BU6P-TR-P-H PL
BL SPFSET 15
BL BL BL 10 +5V2 GY
+5VPOD 1 6 +5VPOD 1 PL GND2 10
GY GY GY 22 SOCD
SPOD GND2 2
PL PL
5 GND2 2
PL
GY
GND2
SPOD 3 4 SPOD 3 6
BL RD
BL 12 +24V3
1754873+179228-3 3 +5V2 4 BR
BL PL PL 19 /SPFC
2 SOCD 5 RD
+5V2 1 GY GY 13 +24V3
PL 1 GND2 6
SOCD SOCD 2
GY
PL
17 /SRRC
GND2 3 21 (NC)
PHNR-2-H+BU2P-TR-P-H
2 +24V3 1
RD
SPF
SPFC 1 /SPFC 2
BR
PHNR-3-H+BU3P-TR-P-H
3 +24V3 1
RD PWB
SRRC 2 (NC) 2
PL
1 /SRRC 3
SMR-03V-NC+SMP-03V-N
BL BL
1 VAREF 1
BR BR
SPFVR GY
2 SPWS 2
GY
3 GND2 3 CNA
B12B-PHDSS-B
1754873+179228-3 BL
1 VAREF
BL BR
+5V2 1 2 SPWS
BR GY
SPLS1 SPLS1 2
GY BL
9 GND2
GND2 3 5 +5V2
BR
4 SPLS1
1754873+179228-3 GY
12 GND2
BL BL
+5V2 1 7 +5V2
PL PL
SPLS2 SPLS2 2
GY GY
6 SPLS2
GND2 3 10 GND2
RD
11 +24V3
PHNR-2-H+BU2P-TR-P-H PL
3 /SPFS
RD
2 +24V3 1
SPFS 1 /SPFS 2
PL
c
GY
SRA-01T-3.2
a
GY
SRA-21T-3
CN10
S28B-PHDSS CN3
RD 9604S-35F FF3-35-R15
1 +24V3 35 VLED
RD VLED 35
2 +24V3 34 DGND
GY DGND 34
3 GND2 33 VAS
GY VAS 33
4 GND2
BL DGND 32 32 DGND
5 +5V1
BL VDS 31 31 VDS
6 +5V2
GY DGND 30 30 DGND
7 GND2 29 SCN
BL SCN 29
8 VAREF 28 DGND
BR DGND 28
9 SPPD 27 LGATE
BR LGATE 27
10 SPFC
BR DGND 26 26 DGND
11 SPED 25 CLK
BR CLK 25
12 SDSS 24 DGND
BR DGND 24
13 SCOV
PL
BR
14
15
SRRC
SPWS
DATA
DGND
LD
23
22
21
23 DATA
22 DGND
21 LD
CIS
PL
16 SPFS
DGND 20 20 DGND
GY
17 GND2
CIS SCLK 19 19 SCLK
PL
PL
18
19
GND2
SPFMO0
DGND
/LST
18
17
18 DGND
17 /LST
un
20 SPOD 16 DGND
DGND 16
PL
PL
BR
21
22
/SPFMA
SOCD cnt SD0
DGND
15
14
15 SD0
14 DGND
23 SPFMA 13 13 SD1
BR SD1
24 SPLS1 12 12 DGND
BR DGND
PL
PL
25
26
/SPFMB
SPLS2 PWB SD2
DGND
11
10
11 SD2
10 DGND
27 SPFMB 9 9 SD3
PL SD3
28 SPFSET 8 8 DGND
DGND
SD4 7 7 SD4
CN7 CN1
S26B-PHDSS B26B-PHDSS DGND 6 6 DGND
BL SD5 5 5 SD5
2_DATA1- 1 1 2_DATA1-
PL DGND 4 4 DGND
2_DATA1+ 2 2 2_DATA1+
PL SD6 3 3 SD6
2_DATA0- 3 3 2_DATA0-
BR DGND 2 2 DGND
2_DATA0+ 4 4 2_DATA0+
BR SD7 1 1 SD7
2_CLK- 5 5 2_CLK-
PL
2_CLK+ 6 6 2_CLK+
PL
2_DBL- 7 7 2_DBL-
BR
2_DBL+ 8 8 2_DBL+
GY
GND2 9 9 GND2
BR
FRM_CCD2 10 10 FRM_CCD2
PL
CLK_CCD2 11 11 CLK_CCD2
PL
PAGE2 12 12 PAGE2 CN2
BR
ADD_CCD2 13 13 ADD_CCD2 B12B-PHDSS-B
BR
TXD_CCD2 14
manuals4you.com
14 TXD_CCD2 SD7 1
PL
RES_CCD2 15 15 RES_CCD2 SD6 2
PL
RXD_CCD2 16 16 RXD_CCD2 SD5 3
OR
+3.3V 17 17 +3.3V SD4 4
OR
+3.3V 18 18 +3.3V SD3 5
RD
+24V3 19 19 +24V3 SD2 6
GY
GND2 20 20 GND2 SD1 7
OR
+12V1 21 21 +12V1 SD0 8
GY
GND2 22 22 GND2 /LST 9
BL
+5V2 23 23 +5V2 SCLK 10
GY
GND2 24 24 GND2 GND2 11
BL
+5V2 25 25 +5V2 GND2 12
BR
/CIS_SET 26 26 /CIS_SET
SCN
cnt
PWB
(3/3)
b
GY
FG
SRA-21T-3
BOARD to BOARD
CN1 1 /RESET
RK-H401SD-0190 TX24-80R-LT-H1 TX25-80P-LT-H1
2 GND2
1 /RESET (NC) 1 1 (NC)
3 DD7
2 GND2 (NC) 2 2 (NC)
3 DD7 PCU_VCCW 3 3 PCU_VCCW
39 /DASP
4 DD8 (NC) 4 4 (NC)
40 GND2
5 DD6 GND 5 5 GND
6 DD9 GND 6 6 GND
7 DD5 HSYNC 7 7 HSYNC
8 DD10 GND 8 8 GND
GND 9 9 GND
HDD
9 DD4
10 DD11 GND 10 10 GND
11 DD3 DTEN 11 11 DTEN
12 DD12 GND 12 12 GND
13 DD2 GND 13 13 GND
14 DD13 GND 14 14 GND
15 DD1 VIDEO1 15 15 VIDEO1
16 DD14 VIDEO0 16 16 VIDEO0
17 DD0 GND 17 17 GND
18 DD15 GND 18 18 GND
19 GND2 +12V_FAN 19 19 +12V_FAN
20 KEY +12V2 20 20 +12V2
21 DMAREQ +12V2 21 21 +12V2
22
23
GND2
/DIOW
GND
+3.3V2
22
23
22
23
GND
+3.3V2
PCU
24 GND2 +3.3V2 24 24 +3.3V2
25 /DIOR +3.3V2 25 25 +3.3V2
26
27
28
GND2
IORDY
CSEL
+3.3V2
GND
HDD-VCC
26
27
28
26
27
28
+3.3V2
GND
HDD-VCC CN2 CN2
PWB
SLD30R-1 SLD30R-1
29 /DMACK HDD-VCC 29 29 HDD-VCC
30 GND2 GND 30 30 GND +12V2 30 30 +12V2
31 INTRQ +5V1 31 31 +5V1 PCU_VCCW 29 29 PCU_VCCW
32 /ICCS10 +5V1 32 32 +5V1 GND 28 28 GND T
33 DA1 +5V1 33 33 +5V1 DTR_PCU 27 27 DTR_PCU T
34 /PDIAG/CBLID +5V2 34 34 +5V2 GND 26 26 GND G
35 DA0 +5V2 35 35 +5V2 DSR_PCU 25 25 DSR_PCU /S
36 DA2 GND 36 36 GND GND 24 24 GND G
37 /CS0 +24V3 37 37 +24V3 TXD_PCU 23 23 TXD_PCU G
38 /CS1 +24V3 38 38 +24V3 GND 22 22 GND G
39 /DASP GND 39 39 GND RXD_PCU 21 21 RXD_PCU L
40 GND2 +12V1 40 40 +12V1 POF 20 20 POF V
DTR_PCU 41 41 DTR_PCU MSW_MON 19 19 MSW_MON G
DSR_PCU 42 42 DSR_PCU GND 18 18 GND G
TXD_PCU 43 43 TXD_PCU RES_PCU 17 17 RES_PCU T
RXD_PCU 44 44 RXD_PCU GND 16 16 GND V
POF 45 45 POF HSYNC 15 15 HSYNC /V
MSW_MON 46 46 MSW_MON GND 14 14 GND /L
RES_PCU 47 47 RES_PCU DTEN 13 13 DTEN G
(NC) 48 48 (NC) BUR_PR 12 12 BUR_PR G
BUR_PR 49 49 BUR_PR GND2 11 11 GND2 +
DCCNT 50 50 DCCNT VIDEO1 10 10 VIDEO1 G
HDDFAN_MON 51 51 HDDFAN_MON VIDEO0 9 9 VIDEO0 +
CNTFAN_MON 52 52 CNTFAN_MON GND 8 8 GND +
PWM 53 53 PWM +5V1 7 7 +5V1 +
GND 54 54 GND +5V2 6 6 +5V2 /V
GND 55 55 GND +5V2 5 5 +5V2 G
GND 56 56 GND +5V2 4 4 +5V2 /S
GND 57 57 GND +5V2 3 3 +5V2 /V
GND 58 58 GND +5V2 2 2 +5V2 /P
+12V_FAN 59 59 +12V_FAN +12V1 1 1 +12V1 /R
+12V2 60 60 +12V2 G
MFP +12V2 61 61 +12V2
MOTHER G
GND 62 62 GND +
CONTROL +3.3V2 63 63 +3.3V2
BOARD G
+3.3V2 64 64 +3.3V2
BOX +3.3V2 65 65 +3.3V2
PWB CN4
S08B-PASK-2
+3.3V2 66 66 +3.3V2 BR
HDD-MON 1
GND 67 67 GND GY
GND2 2
HDD-VCC 68 68 HDD-VCC BR
CFM-PWM 3
HDD-VCC 69 69 HDD-VCC PL
+12V_FAN 4
GND 70 70 GND BR
HDD-MON 5
+5V1 71 71 +5V1 GY
GND2 6
+5V1 72 72 +5V1 BR
CFM-PWM 7
+5V1 73 73 +5V1 PL
+12V_FAN 8
+5V2 74 74 +5V2
+5V2 75 75 +5V2
1 HDD-MON
GND 76 76 GND
2 GND2
+24V3 77 77 +24V3
3 CFM-PWM
FM_HDD
+24V3 78 78 +24V3
4 +12V_FAN
GND 79 79 GND
+12V1 80 80 +12V1
1 HDD-MON
2 GND2
3 CFM-PWM
FM_CNT
4 +12V_FAN
U KEY5
KEY6
20
21
LED1\ 22
LED2\ 23
CN7
173979-2 173981-2 CN4
BK B32B-PHDSS-B
TONER HOPPER TM1 TMA
TMB
1
2
BK
1 TMA
2 TMB
/POMXB 1
BR
BL
+5V2 2
BR
/POMB 3
BR
CN9 POD1 4
9604S-08C BR
8FE-ST-VK-N /POMA 5
GY
DSW-L 8 1 DSW-F GND2 6
BR
DSW-L 7 2 DSW-F /POMXA 7
BL
GND1 6 3 GND2 +5V2 8
RD
MAIN MM GND1 5 4 GND2
5 +5V2
+24V1 9
BR
+5V2 4 POD2 10
RD
GND2 3 6 GND2 +24V1 11
GY
DRIVE MM\
MM-T
2 7 MM\
8 MM-T
GND2
GND2
12
13
GY
1
BL
PCU +5V2
CFM2\
POD3
14
15
16
BR
BR
+24V1 17
GY
TONER HOPPER GND2 18
TSR-04V-K
BR
CN5
B8B-PH-K-S
PWB +24V1
CFM2\
19
20
RD
GND2 1 1 GND2 +24V1 21
GY
CRU +5V2 2 2 +5V2 VFM2\ 22
BL RD
CRUCLK 3 3 CRUCLK +24V1 23
PWB CRUSDA 4
BR
4 CRUSDA GND2 24
GY
BR
5 PSPS\ (NC) 25
RD
PHNR-02-H+BU02P-TR-P-H 6 +24V1 GND2 26
RD
2 PSPS\ 1 7 (NC) DSW-L 27
PSPS 1 +24V1 2 8 +24V1 DSW-L 28
RD
(NC) 29
(NC) 30
DEVELOPER UNIT (NC)
DSW-F
31
32
RD
CN8
QR/P8-12S-C(01) B11B-PH-K-S
BR
1 DVCH1 1 1 DVCH1
BR
2 DVCH2 2 2 DVCH2
BR BR
3 DVCH3 3 3 DVCH3
BR BR
51021-0400 4 TH-DV 4 4 TH-DV
GY GY
(NC) 1 5 GND2 5 5 GND2
GY CN13
+24V1 2 6 GND2 6 6 GND2
TCS TCS 3
BR
7 TCS 7
BR
7 TCS
B24B-PHDSS-B
GY GY GY
GND2 GND2 GND2 1
4 8 8 8 GND2 RD
RD RD +24V1 2
9 +24V1 9 9 +24V1 BR
BL BL PED 3
ZHR-4 10 +5V2 10 10 +5V2 BR
BR BR CPFC\ 4
+5V2 1 11 HUS-DV 11 11 HUS-DV BL
WH WH +5V2 5
HUS-DV 2 12 DVBias 12 RD
HUS-DV +24V1 6
GND2 3 GY
#187 GND2 7
TH-DV 4 Bias BR
RRC\ 8
BR
SRA-21T-3 LUD 9
Bias RD
+24V1 10
BL
+5V2 11
BR
TRC\ 12
GND 13
BR
CSS 14
GY
GND2 15
GY
GND2 16
BR
PPD1 17
BR
LUMB 18
BL
+5V2 19
BR
LUMA 20
BR
CFM1\ 21
GY
GND2 22
RD
+24V1 23
CN22 GY
GND2 24
SHORT JIG 173981-2
1 PCU_RES
2 GND2
179228-3
BL
3 +5V2
BR
BR GY
1 POD2 POD2
1 2 GND2
BL
2
BR
3 179228-3
BR BL
4 3 +5V2
BR BR
5
GY GY
1 POD3 POD3
6 2 GND2
BR
7
BL DSW-L
8
RD RD
9 SFPS-41T-187
BR
10 RD
RD
11
GY
12 SMR-03V-N SMR-03V-N+SMP-03V-NC
DSW-F
GY RD RD RD
13
BL 1 DSW-L 1 1 DSW-L 1
14 SFPS-41T-187
BR 2 (NC) 2 2 (NC) 2
15 RD RD RD
BR 3 DSW-F 3 3 DSW-F 3
16
17
GY PHNR-02-H+BU02P-TR-P-H
18
19
BR RD
20
RD GY
2 CFM2\ 1
BK CFM2 DUCT SECTION
21 1 GND2 2
22
RD
23
GY PHNR-03-H+BU03P-TR-P-H
24
RD RD
25 3 +24V1 1
BR BR PAPER EXIT UN SECTION
26
RD GY
2 VFM2\ 2
GY
VFM2
27 1 GND2 3
RD
28
29
30 LEFT DOOR SECTION
31
RD PHNR-03-H+BU03P-TR-P-H
32 TSR-04V-K PHR-3
GY RD RD
1 GND2 +24V1 1 3 +24V1 1 HVR
RD DRAWER BR BR GY
2 +24V1 CFM1\ 2 2 CFM1\ 2 CFM1
GY
3 GND2 PWB GND2 3
GY
1 GND2 3
GY PWB
BR
4 CFM1\
PS ROLLER
PHNR-03-H+BU03P-TR-P-H
179228-3(AMP)
BL
PHNR-09-H+BU09P-TR-P-H 1 +5V2 3 1 +5V2
GY BL BL 2 PPD1 2
BR
2 PPD1 PPD1 HVR GY
1 1 +5V2 9 GY
2
RD BR
2 PPD1 8
BR 3 GND2 1 3 GND2 PWB
BR GY GY
3 3 GND2 7 179228-3(AMP)
BR BL BL
4 4 +5V2 6 1 +5V2
BL BR BR
5
RD GY
5 LUD 5
GY
2 LUD LUD
6 6 GND2 4 3 GND2
GY BL BL
7 7 +5V2 3
BR BR BR
8 8 PED 2
BR GY GY 179228-3(AMP)
9 9 GND2 1
RD 1 +5V2
10
11
BL 2 PED PED
BR 3 GND2
12
13
14
BR CASETTE UNIT
GY
15
16
GY CN1
S4B-PH-K-S
CSS PWB
BR BR
17 1 CSS CN2
18
BR GY
2 GND2 CSS 173979-2 173979-2
BL BR OR
19 3 LUMB LUMB 1 1 LUMB
20
BR BR
4 LUMA LUMA 2
OR
2 LUMA
LUM
BR
21
GY
22
RD
23
GY PHNR-02-H+BU02P-TR-P-H
24
BR
1 CPFC\ 2
RD
2 +24V1 1 CPFC
PHNR-02-H+BU02P-TR-P-H
BR
1 RRC\ 2
RD
2 +24V1 1 RRC MAIN DRIVE
PHNR-03-H+BU03P-TR-P-H
BR
1 TRC1\ 3
RD
2 (NC) 2 TRC
3 +24V1 1
SRA-51T-4
VLP-03V+VLR-03V CN2
WH WH WH
HL1 1 HL1 HL1 1 1 HL1N 1 B7B-PH-K-S
WH WH WH
2 HL2 HL2 2 2 HL2N 2
BK BK BK +24VPR 1
3 N2 L2 3 3 L 3 (NC)
BK GY 2
HL2
4 F-GND F-GND 4 HLPR
CN1 3
SRA-51T-4 B03P-VL
HLCNT1 4
SRA-51T-4 HL1N
1 HLCNT2 5
SRA-51T-4 HL2N
2 MSW MON
SRA-51T-4 6
3 L
DCCNT/ 7
Lot BL
+5V1 4
#250(BK)
BK
Lout
PWB +5VOPT 5
OR
+3.3V1 6
OR
#250(WH) +3.3V1 7
GY
WH GND2 8
Nout GY
GND2 9
#250(WH) GY
WH GND2 10
Not GY
GND2 11
BR
FW 12
CN4
CN6
BK
1 L B5P-VH
2 (NC) CN7 GND2 1
WH
3 N B2P-VH GND2 2
+5VOPT
+5v1
BK WH +24V4
MSL MSN 4
+5VOPT 5
#250(YL) #250(YL)
BK WH
L N 1 2
#250(WH) #250(WH)
BK WH
L1 N1
#250(BL) #250(BL)
#110(WH)
+24V1
#110(WH)
/MSWPR
BK
WH
BK
WH
B2P3-VH
CN1
B2P3-VH-BK
CN2
1 2 3 1 2 3
MSW LIn
(NC)
MSW NIn
MSW Lout
(NC)
MSW Nout
WH Nout
#250(RD)
WH Nout
#250(RD)
BK
#250(BK)
Lout RELAY
BK
#250(BK)
CN3
Lout PWB B3B-PH-K-S
#250(GR)
#250(GR)
#250(GR)
#250(GR)
+12V2 1
BUP_PR
Lin
Lin
Nin
Nin
2
GND 3
BK
BK
WH
WH
FUSE PWB
VLP-04V+VLR-04V
WH WH
#250(BL) 1 N 1
BK BK BK
L1 2 L 2
WH WH
#250(YL) 3 Not 3
WH BK BK
N1 4 Lot 4
#250(BL)
BK
Lout
#250(YL)
WH
Nout ELP-02V+ELR-02VF
1 DH-L 1
2 DH-N 2
to HDD
to DESK UN (N model
SIN-21T-1.8S
BK
SIN-21T-1.8S
DH-L
FAX
WH
DH-N
AC IN
INLET FAX BK
VLR-06V+VLP-06V-1 L L
CN1
BK BK
BK
B03P-VL
YL/GR
1 LFin 1
YL/GR
POWER WH
N N
L L 3 L
BK
2 FG 2
BK
SW
2 (NC) 3 LFout 3
WH WH WH
1 N 4 NFin 4
FG FG YL/GR YL/GR
5 FG 5
WH WH BK
6 NFout 6 L L
N N DCPR
WH
N N
PCU
GY 9604S-14F 1-84432-4(AMP)
15 GND SRA-21T-4L
RD DSW-F 1 14 DSW-F PS-187
16 GND RD
BL GND2 2 13 GND2 RD MHV
GND2 3 12 GND2
SRA-21T-3
OR PS-187
DHVREM 4 11 DHVREM WH
PWB
OR RD WH THV
1 +24V1 MHVREM\ 5 10 MHVREM\
GY RD
2 +24V2 THV+PWM\ 6 9 THV+PWM\ SRA-21T-4L
PS-187
GY GY WH
GBPWM\ 7 8 GBPWM\
GY
3 GND2
DHVPWM\ 8 7 DHVPWM\
HV YL GB
4 +5V2
GY SRA-21T-3
5 +5V2 THV-PWM\ 9 6 THV-PWM\ PS-187
OR RD
BR
6 +3.3V1 DVREM\ 10 5 DVREM\ BL DHV
OR
7 +3.3V1 DVPWM\ 11 4 DVPWM\
GY PS-187
8 GND2 THVREM\ 12 3 THVREM\
GY GR DV BIAS
9 GND2 MHV-T 13 2 MHV-T
CN17 THin 14 1 THin
B9P-VH
CN23
173981-2
1 XPNC
2 +24V1
ELR-04NVF
GY
1 +5VOPT 1
GY
2 +24V4 2
RD
3 GND2 3
BL
4 GND2 4
to DESK UN
Mother PWB
CN3
ELP-06V-NV+ELR-06N V9PS-VH
BL +5V1 BL
1 1 1 +5V1
BL +5V1 BL
2 2 2 +5V1
GY GND GY GND
3 3 3
RD +24V3 RD +24V3
4 4 4
BR DCCNT BR DCCNT
5 5 5
6
(NC) 6 6 +12V
7 GND2
8 GND2
PL
+12V 1 9 HDD-VCC
GY
GND2 2
GY
GND2 3
BL
HDD-VCC 4
LCP-04
D
del only)
BK
L
WH FAX
DCPS
N
SRA-51T-4
VLP-03V+VLR-03V CN2
WH WH
HL1 HL1 HL1
WH
1
HL2 HL2
1
WH
1 HL1 1
AC/DC B7B-PH-K-S
2 2 2 HL2 2
BK BK +24VPR 1
3 N2 L2 3 3 L2 3
HL2 BK
4 F-GND F-GND 4
GY PWB (NC) 2
HLPR 3
SRA-51T-4
HLCNT1 4
SRA-51T-4
HLCNT2 5
SRA-51T-4
SRA-51T-4 BK MSW MON 6
FILTER
BR DCCNT/ 7
PWB WH
CN1
B03P-VL
HL-1N WH
1 1 HL1
HL-2N WH CN5
2 2 HL2
CN2 BK B12P-HL-A
B03P-VL HL-L 3 3 L2 RD
+24V1 1
L2 BK RD
1 L #187(BK) +24V2 2
(NC) RD
2 +24V3 3
(NC) L2R #187(BK) BL
CN1 3 +5V1 4
B2P4-VH L2R BK
4 +5VOPT 5
OR
+3.3V1 6
OR
BK +3.3V1 7
Lot #250(BK) GY
GND2 8
GY
BK GND2 9
Lout #250(BK) GY
GND2 10
GY
WH GND2 11
Nout #250(WH) BR
FW 12
WH
Not #250(WH)
CN6
B5P-VH
CN4
CN7 GND2 1
BK
1 L B2P-VH GND2 2
2 (NC)
GND2 3
+5VOPT
+5v1
WH
3 N 4
+24V4
MSW B03B-XASK-1
+5VOPT 5
BK WH
MSL MSN
1 2
#250(YL) #250(YL)
BK WH
L N
#250(WH) #250(WH)
BK WH
L1 N1
#250(BL) #250(BL)
BK
WH
BK
WH
B2P3-VH
CN1
B2P3-VH-BK
CN2
1 2 3 1 2 3
MSW LIn
(NC)
MSW NIn
MSW Lout
(NC)
MSW Nout
WH Nout
#250(RD)
WH Nout
#250(RD)
BK
#250(BK)
Lout RELAY
BK
#250(BK)
CN3
Lout PWB B3B-PH-K-S
#250(GR)
#250(GR)
#250(GR)
#250(GR)
+12V2 1
BUP_PR
Lin
Lin
Nin
Nin
2
GND 3
BK
BK
WH
WH
FUSE PWB
VLP-04V+VLR-04V
WH WH
#250(BL) 1 N 1
BK BK BK
L1 2 L 2
WH WH
#250(YL) 3 Not 3
WH BK BK
N1 4 Lot 4
#250(BL)
BK
Lout
#250(YL)
WH
Nout ELP-02V+ELR-02VF
1 DH-L 1
2 DH-N 2
to HDD
to DESK UN (N model
SIN-21T-1.8S
BK
SIN-21T-1.8S
DH-L
FAX
AC IN WH
DH-N
INLET FAX BK
VLR-06V+VLP-06V-1 L L
CN1 BK BK
BK
B03P-VL
YL/GR
1 LFin 1
YL/GR
POWER WH
3 L N N
L L
BK
2 FG 2
BK
SW
2 (NC) 3 LFout 3
WH 1 N WH WH
FG FG 4 NFin 4
YL/GR YL/GR
5 FG 5
WH WH BK
6 NFout 6 L L
N N DCPR
WH
N N
PCU
GY 9604S-14F 1-84432-4(AMP)
15 GND SRA-21T-4L
RD DSW-F 1 14 DSW-F PS-187
16 GND RD
BL GND2 2 13 GND2 RD MHV
GND2 3 12 GND2
SRA-21T-3
OR PS-187
DHVREM 4 11 DHVREM WH
PWB
OR RD WH THV
1 +24V1 MHVREM\ 5 10 MHVREM\
GY RD
2 +24V2 THV+PWM\ 6 9 THV+PWM\ SRA-21T-4L
PS-187
GY GY WH
GBPWM\ 7 8 GBPWM\
GY
3 GND2
DHVPWM\ 8 7 DHVPWM\
HV YL GB
4 +5V2
GY SRA-21T-3
5 +5V2 THV-PWM\ 9 6 THV-PWM\ PS-187
OR RD
BR
6 +3.3V1 DVREM\ 10 5 DVREM\ BL DHV
OR
7 +3.3V1 DVPWM\ 11 4 DVPWM\
GY PS-187
8 GND2 THVREM\ 12 3 THVREM\
GY GR DV BIAS
9 GND2 MHV-T 13 2 MHV-T
CN17 THin 14 1 THin
B9P-VH
CN23
173981-2
1 XPNC
2 +24V1
ELR-04NVF
BL
1 +5VOPT 1
RD
2 +24V4 2
GY
3 GND2 3
GY
4 GND2 4
to DESK UN
Mother PWB
CN3
ELP-06V-NV+ELR-06N V9PS-VH
BL +5V1 BL
1 1 1 +5V1
BL +5V1 BL
2 2 2 +5V1
GY GND GY 3 GND
3 3
RD +24V3 RD 4 +24V3
4 4
BR DCCNT BR 5 DCCNT
5 5
6 (NC) 6 6 +12V
7 GND2
8 GND2
PL
+12V 1 9 HDD-VCC
GY
GND2 2
GY
GND2 3
BL
HDD-VCC 4
LCP-04
D
del only)
o m
BK
o u.c
L
y
WH FAX
DCPS a ls4
u
an
N
K
m
H
CN12 CN10
B30B-PHDSS-B B24B-PADES(BULE)
1 VAREF +5V2 1
2 +5V3 VAREF 2
3 +24V2 +24V2 3
4 +24V2 GND2 4
5 GND2 GND2 5
6 GND2 MCPPD 6
7 ADMEN1\ MCDRS 7
8 ADMCK1\ MCPED 8
9 ADMEN2\ MCLUD 9
10 ADMCK2\ MCPWS 10
11
12
13
MPFC\
MPFS\
DGS\
MCSS1
MCSS2
MCSS3
11
12
13
MULTICS
14 APID MCSS4 14
ADU 15
16
APOD
APPD2
MCSPD
MC SET
15
16
17 APPD1 MCPCL\ 17
18 MPLD1 MCFCL\ 18
19 MPED MCLUM\ 19
20 MPWS MCM-T 20
21 DSW-D MCMCLK\ 21
22 ADU SET MCM\ 22
23 MPF SET MCPFS\ 23
24 MSS\ DCPR\ 24
25 ADM H/L
26 ADUFM\
27
28
MPLS2
MPLS1
PCU
29 (NC)
30 (NC)
PWB CN11
B22B-PADRS(RED)
TXD-FIN1 1
RXD-FIN1\ 2
DTR-FIN1\ 3
DSR-FIN1\ 4
RES-FIN1 5
GND2 6
TXD-FIN2 7
RXD-FIN2\ 8
DTR-FIN2\ 9
DESK
DSR-FIN2\ 10
RES-FIN2 11
GND2 12
TXD-DSK 13
RXD-DSK\ 14
DTR-DSK\ 15
DSR-DSK\ 16
RES-DSK 17
TRC-DSK\ 18
FGS-FIN\ 19
FM1\ 20
DCPR\ 21
+24V2 22
GND2 6
TXD_FIN2 7
RXD_FIN2/ 8
DTR_FIN2/ 9
DSR_FIN2/ 10
RES_FIN2 11
GND2 12
TXD_DSK 13
RXD_DSK/ 14
DTR_DSK/ 15
DSR_DSK/ 16
RES_DSK 17
TRC_DSK/ 18
FGS_FIN/ 19
(N.C) 20
(N.C) 21
(N.C) 22
PCU PWB
CN6
B5P-VH VHR-5N
GND 1 ELP-04NV ELR-04V
GND 2 4 GND GND 4
GND 3 3 GND GND 3
+24V4 4 2 +24V4 +24V4 2
+5VOPT 5 1 +5VOPT +5VOPT 1
AR-D27,28
1 1 1 +24V_D
DCPS SRA-21T-4 SRA-21T-3 2 2 2 P-GND
3 3 3 +5V
4 4 4 GND2
5 5 5 S-GND
6 6 6 TXD_DSK
7 7 7 RXD_DSK/
8 8 8 DTR_DSK/
9 9 9 DSR_DSK/
Main body 10 10 10 RES_DSK
CNB 11 11 11 TRC_DSK
SMP-11V-BC SMR-11V-B
B22B-PADRS / PADP-22V-1-R
+5V 1
+5V 2
S-GND 3 AR-FN6,MS1
+5V 4
S-GND 5 1 1 1 +5V
+24V_F 6 2 2 2 +24V_F
S-GND 7 3 3 3 GND2
+24V_F 8 4 4 4 S-GND
S-GND 9 5 5 5 P-GND
+24V_F 10 6 6 6 F-GND
CNA P-GND 11 7 7 7 TXD_FIN2
VHR-5N / B5P-VH +24V_F 12 8 8 8 RXD_FIN2
1 GND P-GND 13 9 9 9 DTR_FIN2/
2 GND +24V_F 14 10 10 10 DSR_FIN2/
3 GND P-GND 15 11 11 11 RES_FIN2
4 +24V4 +24V_D 16 12 12 12 FGS_FIN/
5 +5VOPT P-GND 17 13 13 13 +24V_F
P-GND 18 14 14 14 +24V_F
GND 19 15 15 15 P-GND
GND 20 16 16 16 P_GND
AR-FN7
Power I/F PWB UN 1 1 1 TXD_FIN1
2 2 2 RXD_FIN1/
3 3 3 DTR_FIN1/
4 4 4 DSR_FIN1/
5 5 5 RES_FIN1
6 6 6 +24V_F
7 7 7 +5V
8 8 8 GND2
9 9 9 S-GND
10 10 10 F-GND
11 11 11 +24V_F
12 12 12 P-GND
ELP-12V ELR-12V
OPTION I/F UN
DH-LINE (OPTION) (1/1)
SRA-21T-4
GR/YL GR/YL DESK
SRA-21T-4
CN-A
B2P3-VH(BK)
ELP-02V+ELR-02VF BK
1 DH-L
BK
1 DH-L 1 2 (NC)
WH WH
2 DH-N 2 3 DH-N
PWB
manuals4you.com
SCN
CN-C
ELP-02V+ELR-02V B2P3-VH
ELR-02VF+ELP-02V BK
BK 1 DH-L(DHSW)
1 DH-L(DHSW) 1 BK
1 DH-L(DHSW) 1 2 (NC)
DH_DH1 WH WH WH
2 DH-N(SCN) 2 3 DH-N(SCN)
2 DH-N(SCN) 2
AC CABLE
BK
DH_DH2 WH
*2: Options
manuals4you.com
manuals4you.com
Memo
LEAD-FREE SOLDER
The PWB’s of this model employs lead-free solder. The “LF” marks indicated on the PWB’s and the Service Manual mean “Lead-Free” solder.
The alphabet following the LF mark shows the kind of lead-free solder.
Example:
Bi-Sn-Ag-P p
Bi-Sn-Ag
manuals4you.com
CAUTION FOR BATTERY REPLACEMENT
(Danish) ADVARSEL !
Lithiumbatteri – Eksplosionsfare ved fejlagtig håndtering.
Udskiftning må kun ske med batteri
af samme fabrikat og type.
Levér det brugte batteri tilbage til leverandoren.
(English) Caution !
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type
recommended by the manufacturer.
Dispose of used batteries according to manufacturer’s instructions.
(Finnish) VAROITUS
Paristo voi räjähtää, jos se on virheellisesti asennettu.
Vaihda paristo ainoastaan laitevalmistajan suosittelemaan
tyyppiin. Hävitä käytetty paristo valmistajan ohjeiden
mukaisesti.
(French) ATTENTION
Il y a danger d’explosion s’ il y a remplacement incorrect
de la batterie. Remplacer uniquement avec une batterie du
même type ou d’un type équivalent recommandé par
le constructeur.
Mettre au rebut les batteries usagées conformément aux
instructions du fabricant.
(Swedish) VARNING
Explosionsfara vid felaktigt batteribyte.
Använd samma batterityp eller en ekvivalent
typ som rekommenderas av apparattillverkaren.
Kassera använt batteri enligt fabrikantens
instruktion.
(German) Achtung
Explosionsgefahr bei Verwendung inkorrekter Batterien.
Als Ersatzbatterien dürfen nur Batterien vom gleichen Typ oder
vom Hersteller empfohlene Batterien verwendet werden.
Entsorgung der gebrauchten Batterien nur nach den vom
Hersteller angegebenen Anweisungen.
Trademark acknowledgements
• Microsoft® Windows® operating system is a trademark or copyright of Microsoft
Corporation in the U.S.A. and other countries.
• Windows® 95, Windows® 98, Windows® Me, Windows NT® 4.0, Windows® 2000,
and Windows® XP are trademarks or copyrights of Microsoft Corporation in the
U.S.A. and other countries.
• IBM and PC/AT are trademarks of International Business Machines Corporation.
• Acrobat® Reader Copyright® 1987- 2002 Adobe Systems Incorporated. All rights
reserved. Adobe, the Adobe logo, Acrobat, and the Acrobat logo are trademarks of
Adobe Systems Incorporated.
• All other trademarks and copyrights are the property of their respective owners.
SHARP CORPORATION
Digital Document System Group
Quality Enhancement Center
Yamatokoriyama, Nara 639-1186, Japan
2005 February Printed in Japan
manuals4you.com
q PARTS GUIDE
CODE:00ZARM351U004
Because parts marked with "!" is indispensable for the machine safety maintenance and operation, it must be replaced with
the parts specific to the product specification.
F Other than this Parts Guide, please refer to documents Service Manual(including Circuit Diagram)of this model.
F Please use the 13 digit code described in the right hand corner of front cover of the document, when you place an order.
F For U.S. only-Use order codes provided in advertising literature. Do not order from parts department.
[NOTE]
* There patrs are supplied by SMF
・New & Addition, Change, Abolition, and Quantity change are expressed with the marks shown in the
table below.
<Change of Division>
New & Addition
Change
Abolition
Q'uantity (increase) /Others
Q'uantity (decrease)
Correction
<Effective Time>
R/ C Running Change
manuals4you.com
1 Exteriors
Inter- PRICE NEW PART Effective
NO. PARTS CODE change RANK MARK RANK DESCRIPTION TR No. time
1 GCAB-0938FCNZ AY D Right cabinet
2 LX-BZ0909FCZZ AC C Screw
3 TLABZ4693FCZZ AF D D mark label [Except U.S.A,CANADA]
4 TLABZ4694FCZZ AF D Imager label [U.S.A,CANADA]
5 GCAB-0940FCN3 BA D Paper exit tray cabinet
6 TLABZ0105RSZZ AD D LAG label [Argentina]
7 TLABH4438FCZZ AD D Label Spain [U.Kingdom,Europe,Argentina]
11 GCAB-1079FCZZ AQ D Front cabinet upper right
13 GCAB-0934FCN2 AW D Front cabinet
14 GCAB-0935FCNZ AN D Front cabinet upper
15 XEBS740P10000 AA C Screw(4×10)
16 GCAB-1080FCZZ AR D Upper cabinet left
17 GCAB-0937FCNZ AL D Left cabinet rear
GCAB-0941FCZ3 AX D Rear cabinet [Except AR-M312U,AR-M420U]
18
GCAB-0941FCZ1 AW D Rear cabinet [AR-M312U,AR-M420U]
19 PFTA-0139FCZZ AD C Delivery tray cabinet cover
20 GCAB-0939FCN2 AL D Right cabinet rear
21 XHBS740P08000 AA C Screw(4×8)
22 LPLTM5937FCZZ AS C Rear cabinet support plate
23 PCOVP1554FCNZ AF C Harness cover
24 PCOVP1618FCZZ AG C ROM cover
25 XHBS730P06000 AC C Screw(3×6)
CBDGD0047FC04 AN C Badge [AR-M355N]
CBDGD0047FC05 AN C Badge [AR-M455N]
CBDGD0047FC15 AN C Badge [AR-M351N]
CBDGD0047FC17 AN C Badge [AR-M351U]
CBDGD0047FC09 AN C Badge [AR-M355U]
26
CBDGD0047FC18 AN C Badge [AR-M451U]
CBDGD0047FC16 AN C Badge [AR-M451N]
CBDGD0047FC10 AN C Badge [AR-M455U]
CBDGD0047FC22 AM C Badge [AR-M312U]
CBDGD0047FC23 AM C Badge [AR-M420U]
27 JHNDP0158FCZZ AE C Handle R lower
TLABS4306FCZZ AC D Noise label class A [U.S.A,CANADA]
30
TLABZ4818FCZZ AD D Argentina standard label [Argentina]
FCC conformity label A,B [U.S.A,CANADA]
TLABF2705FCZZ AB D
31 [Except AR-M312U,AR-M420U]
TLABH4186FCZZ AE D Class A VCCI label [AR-M312U,AR-M420U]
32 TCAUA0770FCZZ AB D Service cautions label
CE mark label [U.Kingdom,Europe,Lebanon,Iran,
33 TLABS3760FCZZ AC D
West Africa,Pakistan,Algeria]
34 TLABH0108GCZZ AC D Class 1 label EGI [Except U.S.A,CANADA]
35 TLABZ4173FCZZ AG D Connection apparatus caution label [U.kingdom,Europe]
36 LPLTM6372FCZZ AC C Front cabinet catch plate
37 PMAGT0144FCPZ AH C Front cabinet magnet
38 XEBS740P14000 AB C Screw(4×14)
39 XEBS730P06000 AA C Screw(3×6)
– 1-1 –
1 Exteriors
25 25 24
34
27 21
21 23 32
21 35
22 21
30 20
31 33
15 2
7 6
21 5 2
19
18
15 21 21 1
21
17 15
21
15 16
15 15
11
21
26 15
14 38
36 39
37
13
4
FCP09281 3
– 1-2 –
manuals4you.com
2 Left door unit
Inter- PRICE NEW PART Effective
NO. PARTS CODE change RANK MARK RANK DESCRIPTION TR No. time
1 PGIDM2077FCZ1 AL D Reverse gate
2 XRESP40-06000 AA C E type ring(E4)
3 LX-BZ0147FCZ1 AC C Screw
4 PGIDM1885FCZZ AR D Left door exit paper reverse guide
5 PGIDM1884FCZZ AU D Left door transfer PG
6 MSPRC2953FCZZ AB C Reverse PG support spring
7 LSTYM0258FCZZ AG C Left door support plate upper
8 LSTYM0259FCZZ AD C Left door support plate lower
9 PTME-0287FCZ1 AD C Transfer lock pawl
11 LHLDZ1439FCZZ AC C Transfer unit pressure holder
12 MSPRC2835FCZZ AC C TR pressure spring
13 LANGT1407FCZ2 AR C ACC fixing angle F
14 XEBS740P12000 AA C Screw(4×12)
15 MLEVP0781FCNZ AD C Left door release lever
16 PTME-0279FCZ1 AB C Left door lock pawl
18 LSTYM0256FCZZ AN C Rail support plate F
19 GDOR-0030FCN1 BC D Left door
20 PCOVP1531FCNZ AK C Left door cover lower
21 CPWBF1599FCE1 AF E Drawer PWB
22 DHAI-3235FCZZ AE C Left door interface harness
23 QEARP0136FCZZ AD C Left door transfer earth plate
24 CPWBF1593FCE2 AK E High voltage resistor PWB
26 PCOVP1567FCNZ AC C Left door upper cover
27 NFANP0069FCZZ AV B Fan
28 LX-WZ0028FCZZ AA C Washer
29 XEBS730P10000 AC C Screw(3×10)
30 LPINS0320FCZZ AB C Spring pin(φ2-8)
31 NSFTZ2572FCZZ AH C Lock lever joint shaft
32 LANGT1409FCZ1 AH C ACC fixing angle R lower
33 LSTYM0257FCZ1 AL C Rail support plate R
34 MSPRD2838FCZZ AC C Left door lock spring
35 XEBS740P10000 AA C Screw(4×10)
36 XRESP50-06000 AA C E type ring(E5)
37 LANGT1408FCZ1 AG C ACC fixing angle R upper
38 XHBS740P06000 AA C Screw(4×6)
40 XEBS730P14000 AD C Screw(3×14)
41 XEBS740P08000 AA C Screw(4×8)
42 PMLT-1263FCZZ AD C Suction cushion A
43 PMLT-1266FCZZ AD C Suction cushion D
44 PMLT-1265FCZZ AD C Suction cushion C
45 PMLT-1264FCZZ AD C Suction cushion B
46 LX-BZ0465FCWZ AA C Screw(4×6)
48 MSPRT2836FCZZ AC C Reverse gate spring
50 PFILZ0287FCZZ AU A Ozone filter
(Unit)
901 CDOR-0030DS52 BP E Left door unit
– 2-1 –
2 Left door unit
2
46 38
1
37 48
41 35 29
6
38 3
41
35
6 3
6
41 7
36
16 35 4
33 41 34 8 14
30
46 38 14
5 14 14
41 31 41 9
32 42
41
41 30 43
38 44
26
45
38 11
29 26 29 12
a 27 28
38
24 14
23 11
50 12
14
41 14
40
2122 13
a 16
36
15 46
18
20
19
FCP09282
– 2-2 –
manuals4you.com
3 PS roller unit
Inter- PRICE NEW PART Effective
NO. PARTS CODE change RANK MARK RANK DESCRIPTION TR No. time
1 NROLP1512FCZZ AX C PS follower roller
2 MSPRT2839FCZZ AF C PS pressure spring
3 NBRGC0286FCZZ AC C PS follower roller bearing
4 NGERH1611FCZZ AC C PS follower gear
5 NGERH1474FCZZ AC C PS gear
6 LPINS0155FCZZ AA C Pin(φ3-10)
7 XRESP70-08000 AA C E type ring(E7)
8 NROLR1303FCZ1 AY B PS roller
9 PGIDH1960FCZZ AK C Paper powder remove guide
10 XEBS730P08000 AC C Screw(3×8)
13 PCLR-0460FCZZ AC C Transfer follwer collar
14 MSPRC3343FCZZ AC C PS front pressure spring
15 NSFTZ2573FCZ1 AG C PS follower roller shaft
17 CPWBF1593FCE1 AK E High voltage resister PWB PS
18 MSPRP1550FCZZ AA C TC spring
19 DHAI-3145FCZZ AE C PPD harness
20 VHPGP2A200L-1 AR B LED(GP2A200L)
23 NBRGP0666FCZZ AC C Bearing
24 JKNBZ0139FCZ2 AD C PS knob
25 MSPRC2841FCZ2 AC C PS brake spring
26 LPINS0325FCZZ AB C Spring pin
28 PGIDM1887FCZ1 AQ D PS paper guide A
29 PCLR-0461FCZZ AC C U-turn collar
30 NROLR1507FCZZ AZ B PS front roller
31 LSTYM0260FCZZ AK C Support stay
32 PGIDM1888FCZZ AL D PS paper guide B
34 PSHEP4825FCZZ AD C PS roller front sheet
36 QEARP0181FCZZ AD C PS earth plate
37 NCPL-0059FCZZ AC C PS coupling
38 LX-BZ0589FCP1 AA C Screw
39 LX-WZ0070FCZZ AA C Washer
40 CGIDH1961FC01 AQ C Drum front PG
manuals4you.com
41 XHBS730P06000 AC C Screw(3×6)
42 TLABZ4731FCZZ AF D Arrow label A [U.Kingdom,Europe]
43 XEBS740P12000 AA C Screw(4×12)
(Unit)
901 CGIDM1887DS52 BH E PS roller guide unit(Without No.42,43)
– 3-1 –
3 PS roller unit
2
10 5 3
41 4
40 1
6
7
8 3
2
10
17 10
37
38 23
9 10
13
18 14 10
37
23 15
19 14
36 20
13 10
10
18
34
10 23
10
39
29 28 24
25
43
26
10 31
23
10 7
42
30 32
FCP09283
– 3-2 –
manuals4you.com
4 Main drive unit
Inter- PRICE NEW PART Effective
NO. PARTS CODE change RANK MARK RANK DESCRIPTION TR No. time
2 NSFTZ2584FCZZ AG C DV joint shaft
3 XRESP50-06000 AA C E type ring(E5)
4 MSPRC2616FCZZ AC C DV drive spring
5 NCPL-0046FCZZ AC C DV coupling
6 LX-BZ0845FCZZ AC C Screw
8 NBRGC0387FCZ1 AC C Bearing
9 XHBS730P06000 AC C Screw(3×6)
10 LPLTM5712FCZZ AE C DV drive plate
11 LPINS0337FCZZ AB C Pin(φ3-12)
12 NGERH1240FCZZ AD C DV drive gear(14T)
13 LPLTM5713FCZZ AC C DV joint plate
14 XHBS730P08000 AB C Screw(3×8)
15 DHAI-3635FCPZ AY C DV interface harness
16 NGERH1363FCZZ AC C Cleaner TB gear(19T)
17 NBRGC0190FCZ1 AD C F6 bearing
19 NCPL-0054FCZZ AE C Cleaner coupling
20 NCPL-0048FCZZ AK C Drum coupling
22 NBRGY0627FCZZ AK C Bearing
23 XBPSD30P08K00 AA C Screw(3×8K)
24 MSPRP1293FCZZ AB C Electrode spring
25 LX-BZ0670FCP1 AC C Drive joint stop screw
27 QCNCM0999FCZZ AC C Connector(BU02P-TR-P-H)(2pin)
28 QCNCM1000FCZZ AC C Connector(BU03P-TR-P-H)(3pin)
29 XEBS740P10000 AA C Screw(4×10)
30 LPLTM5714FCZZ AB C M3 plate
31 LFRM-1016FCZZ BA D Transfer drive frame lower
32 QEARP0116FCZZ AC C Left cabinet earth spring
33 MSPRP2823FCZZ AD C TB spring
34 DHAI-3427FCZZ AN C HV harness
35 PCOVP1611FCZZ AC C Transfer high voltage cover
36 CPLTM5711FC01 AH C DV gear fixing plate
37 QEARP0117FCZZ AC C Drum earth joint spring
38 NSFTZ2585FCZZ AG C Cleaner TB shaft
39 NGERH1416FCZZ AE C Cleaner gear
40 NSFTZ2580FCZZ AK C Drum turn shaft
41 NGERH1413FCZZ AM C Drum gear
42 NGERH1415FCZZ AN C DR idle gear
43 NGERH1429FCZZ AE C DV drive gear
44 NSFTZ2579FCZZ AE C Drum motor shaft
46 PCOVP1534FCZZ AX D Transfer drive cover
47 QEARP0118FCZZ AC C Transfer earth joint spring
48 QEARP0115FCZZ AF C Drum earth plate
49 LPLTM5762FCZZ AC C Rear cabinet fixing plate B
50 PSHEP4826FCZZ AC C Pulley sheet
51 NPLYZ0419FCZZ AD C Elevator drive pulley(22PS3M)
52 NSFTZ2581FCZZ AE C Fusing drive shaft
53 NGERH0349FCZZ AC C Gear(CL28T)
54 NSFTZ2883FCZZ AP C Main drive joint shaft
55 NGERH0457FCZZ AC C DV drive gear R
56 NSFTZ2577FCZZ AL C Main motor shaft
57 NGERH1528FCZZ AE C PS drive gear
58 NGERH1357FCZZ AD C Gear(48/28T)
59 PCLC-0298FCZZ AT B Paper feed clutch
60 PCLC-0297FCZZ AU B PS front clutch
61 NGERH1414FCZZ AC C Paper feed joint gear
62 NSFTZ2583FCZZ AF C Paper feed shaft
63 NSFTZ2575FCZ1 AF C PS front roller shaft
64 PCLC-0296FCZ1 AX B PS clutch
66 NGERH1359FCZZ AD C Gear(15/24T)
67 LX-BZ0788FCZ1 AC C Screw
68 XRESP70-08000 AA C E type ring(E7)
69 XRESP60-07000 AA C E type ring(E6)
70 LX-BZ0576FCZZ AC C Screw(4×6)
71 NSFTZ2576FCZ2 AF C PS roller shaft
72 XRESP40-05000 AA C E type ring(E4)
73 NBRGC0641FCZZ AD C Bearing
74 LPINS0330FCZZ AB C Spring pin(φ3-16)
75 LPINS0155FCZZ AA C Pin(φ3-10)
76 XNES730-18000 AA C Nut
77 XBPS730P06K00 AA C Screw(3×6K)
78 XEBS740P10000 AA C Screw(4×10)
79 XRESP40-05000 AA C E type ring(E4)
80 LPINS0133FCZZ AA C Pin(2×10)
81 LHLDW1006FCZZ AA C Mini clamp(UAMS-09-0)
82 NBRGY0773FCZZ AP C Bearing
83 NSFTZ2578FCZZ AN C DV joint shaft
84 LX-BZ0033GCZZ AC C Screw
85 PSHEP4947FCZZ AC C PS front clutch sheet
86 PSHEP4948FCZZ AC C PF clutch sheet
87 PSPAZ1430FCZZ AB C Spacer(φ8-8)
– 4-1 –
4 Main drive unit
Inter- PRICE NEW PART Effective
NO. PARTS CODE change RANK MARK RANK DESCRIPTION TR No. time
88 LX-WZ0070FCZZ AA C Washer
89 LX-WZ0017FCPZ AA C Adjust Washer
90 MSPRC3027FCZ1 AD C PS front spring
91 LX-WZ0421FCZZ AA C Washer
92 LX-WZ0198FCZZ AA C Washer
(Unit)
901 CFRM-1016DS53 BR E Main drive unit(Without No.29,49)
73 78 78
68
54 46 78 49
55 68
11 29
75 51
52 82
FCP09284 68 78 50
68
53
– 4-2 –
manuals4you.com
5 Transfer unit
Inter- PRICE NEW PART Effective
NO. PARTS CODE change RANK MARK RANK DESCRIPTION TR No. time
1 LHLDZ1482FCZ3 AF C Discharge plate holder
2 LPLTM5875FCZ1 AK B Discharge plate
3 PGIDM1950FCZ2 AE D Transfer front PG
5 LPLTM5925FCZZ AQ C Transfer front PG plate
6 XEBS740P08000 AA C Screw(4×8)
7 MSPRC3000FCZZ AC C Transfer front PG spring
8 NROLR1355FCP1 AZ B Transfer roller
9 NBRGP0655FCZZ AD C TR bearing F
10 PCLR-0468FCZ1 AC C Transfer roller collar
11 MSPRC2955FCZZ AB C Reverse pressure spring
12 LHLDZ1474FCZ2 AL D TR holder
13 LPLTM5926FCZ1 AS C Holder support plate
14 PTME-0288FCZZ AC C Transfer lock pawl
15 NGERH1419FCZZ AK C TR gear
16 QEARP0132FCZZ AE C TR earth plate
17 XBPS730P06KS0 AB C Screw(3×6KS)
18 NBRGP0656FCZZ AD C TR bearing R
19 PRNGF0107FCZZ AC C Starling
20 MSPRC3342FCZZ AC C Transfer R pressure spring
(Unit)
901 CHLDZ1474DS52 BF E Transfer unit
5 Transfer unit
17
19
19
19
19
2 19
6
19
1
16
18
10
20
15 3
7
8 5
6
14
6
13
6 9
6 10
11
12
6
FCP09285
– 5-1 –
Update : 06/02/27
6 Cassette paper feeder
Inter- PRICE NEW PART Effective
NO. PARTS CODE change RANK MARK RANK DESCRIPTION TR No. time
LDAIU0622FCZZ AY C Paper feed base plate
1
LDAIU0622FCZ1 5 AU C Paper feed base plate [Unleaded correspondence][With No.14-57] 05/09
2 XEBS740P10000 AA C Screw(4×10)
3 PCOVP1543FCZ1 AF C Paper feed upper cover
4 DHAI-3155FCZZ AK C Cassette detect interface harness
5 MLEVP0785FCZZ AE C PE actuator
6 VHPGP1A73A+-1 AG B Photo sensor(GP1A73A)
7 PGIDM1891FCZZ AG C Pick-up roller guide
8 NSFTZ2591FCZZ AF C Pick-up roller shaft
9 NPLYZ0365FCZZ AC C Pick-up roller pulley
10 NROLR1509FCZZ AX B Pick-up roller
11 NBLTH0432FCZZ AF B Belt(55MXL3.2)
12 NROLR1508FCZZ AX B Paper feed separation roller
13 PCLC-0348FCZZ AP C Separete torque limiter
14 NCPL-0049FCZZ AH C Oneway coupling
15 NSFTZ2590FCZ1 AH C Separation roller shaft
16 NPLYZ0373FCZZ AH C Paper feed roller pulley
17 XRESP50-06000 AA C E type ring(E5)
19 LX-BZ0960FCZZ AC C Screw(φ16)
PCLR-0441FCZZ AK C Collar(φ16)
20
PCLR-0519FCZZ 1 AE C Collar(φ16) 06/05
21 LRALP0185FCZ1 AQ D Left rail
22 PGIDM1893FCZZ AH C Paper feed PG
23 PGIDM1892FCZZ AE C Separation roller guide
24 PRNGP0090FCZZ AA C Ring(E5)
26 XPSSJ20-08000 AA C Spring pin(φ2-8)
27 LPINS0329FCZZ AB C Spring pin(φ2-16)
28 NSFTZ2589FCZZ AL C Paper feed roller shaft
29 NBRGC0387FCZ1 AC C Bearing
30 MSPRC3012FCZZ AC C Paper feed brake spring
31 NCPL-0047FCZZ AC C Paper feed coupling
32 LX-BZ0916FCPZ AA C Screw
34 MARMP0259FCZZ AC C Pick-up roller arm
35 MSPRD2850FCZZ AE C Pick-up roller arm spring
36 CPLTM5732FC01 AF C Pick-up roller arm fixing plate
37 XHBS740P08000 AA C Screw(4×8)
38 MSPRT3341FCZZ AC C Separete pressure spring
39 PSPAZ1429FCZZ AB C Spacer
– 6-1 –
manuals4you.com
Update : 06/02/27
6 Cassette paper feeder
36
35
37 6 1
6
34 a
17
b 2
7 5
32
31 4
30
39
29
a 3
24 17 b
27 28
8
23
17
9
17 29
26 10
17
38 16
15 11
14 12
22
13
12
21
19
20
FCP09286
– 6-2 –
7 Fusing unit
Inter- PRICE NEW PART Effective
NO. PARTS CODE change RANK MARK RANK DESCRIPTION TR No. time
1 PGIDM1895FCZZ AN D Fusing rear upper PG
2 LX-BZ3008SCPS AA C Screw(3×8)
3 PTME-0300FCZZ AK C Upper separator pawl
4 MSPRT2852FCZZ AB C Top pawl spring
5 XHBS740P08000 AA C Screw(4×8)
RDTCT0164FCZZ AR B Thermistor [Except AR-M312U,AR-M420U]
6
RDTCT0147FCZZ AR B Thermistor [AR-M312U,AR-M420U]
7 LX-BZ0905FCPZ AB C Screw(3×12KS)
8 DHAI-3156FCZZ AT C Fusing harness
10 XBPS730P08KS0 AB C Screw(3×8KS)
11 PCOVP1546FCZ1 AY D Fusing upper cover
12 LPLTM5737FCZZ AD C Lamp fixing plate F
13 LX-NZ0094FCZZ AC C Nut(M3)
14 LPLTM5739FCZZ AD C Thermostat fixing plate
15 RTHM-0024FCZZ AM B Thermostat
16 QEARP0123FCZZ AE C Electrode plate
17 LPLTM5738FCZZ AD C Lamp fixing plate R
18 LSTYM0268FCZZ AE C HR support plate R
19 LFIX-0442FCZZ AB C Fusing shaft fixing plate R
20 LSTYM0267FCZZ AE C HR support plate F
! RLMPU0662FCZZ AX B Heater lamp sub 120 [120V series]
21
! RLMPU0664FCZZ AY B Heater lamp sub 240 [200V series]
22 NROLI1314FCZ1 BH B Pressure roller
! RLMPU0661FCZZ AX B Heater lamp main 120 [120V series]
23
! RLMPU0663FCZZ AY B Heater lamp main 240 [200V series]
24 NBRGY0773FCZZ AP C Bearing
25 PGIDM1894FCZZ AP C Fusing front lower PG
27 CSTYM0265FC02 AF C Pressure support plate F
28 MLEVP0790FCZ2 AE C Fusing lever F
29 XEPS840P08X00 AC C Screw(4×8X)
30 MLEVP0786FCZZ AC C Pressure adjust lever F
31 LX-BZ0906FCZZ AC C Screw(M4)
32 CFLT-0064FC06 AN C Fusing cushion
33 PCOVP1547FCZZ AY D Fusing lower cover
34 MLEVF0788FCZ3 AF C Pressure lever F
35 XRESP50-06000 AA C E type ring(E5)
36 MSPRC3327FCZZ AC C Fusing pressure spring
37 CSTYM0266FC02 AF C Pressure support plate R
38 MLEVF0789FCZ3 AF C Pressure lever R
39 MLEVP0791FCZ2 AE C Fusing lever R
40 MLEVP0787FCZZ AC C Pressure adjust lever R
41 PTME-0283FCZZ AL C Lower separator pawl
42 MSPRD2853FCZZ AB C Lower pawl spring
43 PGIDM1951FCZ1 AQ D Fusing rear lower PG
44 LSTPF0172FCZZ AA C Roller stopper
45 NBRGY0646FCZZ AS C Bearing
NROLT1549FCZZ BE A Heat roller upper [Except AR-M312U,AR-M420U]
46
NROLT1313FCZZ BE A Heat roller upper [AR-M312U,AR-M420U]
47 NGERH1380FCZZ AQ B Fusing gear(48T)
48 TLABZ4205FCZZ AC D Green label
49 XHPS730P06000 AA C Screw(3×6)
50 LFIX-0441FCZZ AB C Fusing shaft fixing plate F
51 MSPRT2957FCZZ AC C PG open close spring
NROLM1560FCZZ BA B CL roller [Except AR-M312U,AR-M420U]
52
NROLM1387FCZZ AL B CL roller [AR-M312U,AR-M420U]
53 NBRGP0670FCZZ AD C CL roller bearing
54 MSPRT3028FCZZ AD C CL roller spring
55 LX-BZ0997FCZZ AB C Screw
56 LSTPP0381FCZZ AE C Stopper R
57 LRTNP0012FCPZ AD C Retainer
(Unit)
DUNTW7095DS15 BZ E Fusing unit(Without No.56) [120V series][Except AR-M312U,AR-M420U]
DUNTW7095DS11 CB E Fusing unit(Without No.56) [120V series][AR-M312U,AR-M420U]
901
DUNTW7095DS16 BZ E Fusing unit(Without No.56) [200V series][Except AR-M312U,AR-M420U]
DUNTW7095DS12 CB E Fusing unit(Without No.56) [200V series][AR-M312U,AR-M420U]
– 7-1 –
manuals4you.com
7 Fusing unit
1
3 2
3
4
4 3
3
5 4
4 7
17
6 6
18 5 5
16
14 7
15 5
50 10 14
44 13 11
49
47 10 7
45 8
12 57
49
19 20
46
55
48
21
45 44
43 24
23
53 22
42
56 51
41
39 42
5 41 55
29 52
40 38
37 24
31 53
36
35 34
5 54 25
36
35
2
54
27
33 5
30
5 31 28
32 2
29
FCP09287
– 7-2 –
8 Delivery turn over unit
Inter- PRICE NEW PART Effective
NO. PARTS CODE change RANK MARK RANK DESCRIPTION TR No. time
1 PMLT-1408FCZZ AC C Exhaust cushion
2 LPLTM5921FCZ1 AQ C Paper exit upper PG support plate
3 XEBS740P10000 AA C Screw(4×10)
4 XHBS740P08000 AA C Screw(4×8)
5 NFANP0075FCZZ BA B Fan
6 MLEVP0828FCZZ AD C Paper exit actuator
7 MLEVP0838FCZZ AC C Detect lever
8 MLEVP0792FCZ1 AD C Paper exit actuator
VHPGP1SQ73P-1 AF B Photo sensor(GP1SQ73P) [Except AR-M312U,AR-M420U]
9
VHPGP1A73A+-1 AG B Photo sensor(GP1A73A) [AR-M312U,AR-M420U]
PGIDM1896FCZ1 AV D Paper exit upper PG [AR-M355U/N,AR-M455U/N]
Paper exit upper PG [Incorrect insertion prevention]
PGIDM1896FCZ2 6 AS D 04/12
10 [AR-M355U/N,AR-M455U/N]
PGIDM1896FCZ4 3 AS D Paper exit upper PG [Form change][AR-M355U/N,AR-M455U/N] 05/12 R/C
PGIDM1896FCZ4 AS D Paper exit upper PG [AR-M351U/N,AR-M451U/N,AR-M312U,AR-M420U]
11 NROLP1296FCZZ AC C Paper exit follower roller
12 NSFTZ2593FCZZ AF C Paper exit follower roller shaft
14 LDAIU0626FCZ2 AK C Paper exit follower roller fixing plate
15 NROLR1315FCZ2 AM B Exit paper roller
16 NGERH1384FCZZ AC C Paper exit gear(30T)
17 NBRGC0387FCZ1 AC C Bearing
18 NBRGC0504FCZZ AC C PF bearing(F8×12×5 16X)
19 XRESP70-08000 AA C E type ring(E7)
20 NROLR1316FCZ3 AS B Fusing roller rear
21 LFRM-1020FCZ1 AZ D Paper exit frame
22 MLEVP0793FCZZ AE C Fusing rear actuator
24 PCLR-0462FCZZ AE C Collar
25 NGERH1398FCZZ AL C Gear(24T)
26 NGERH1383FCZZ AD C Fusing drive gear(30T)
27 LPINS0265FCZZ AB C Spring pin(M3×12)
28 CPLTM5740FC01 AE C Fusing joint plate
29 MSPRT2858FCZZ AC C Fusing joint spring
30 MSPRC2857FCZZ AA C Paper exit follower roller spring
31 NSFTZ2594FCZZ AP C Fusing rear follower shaft
32 NROLP1473FCZZ AF C Fusing rear follower roller
33 NSFTZ2595FCZZ AN C Fusing knob shaft
34 JKNBZ0140FCZZ AF C Fusing knob
35 NGERH1593FCZZ AQ C Fusing drive gear(30T)
36 NSFTZ2598FCZ1 AG C Fusing drive joint shaft
37 NGERH1421FCZ1 AH C Oneway gear(30T)
38 NBLTH0327FCZ1 AL B Belt
40 NPLYZ0385FCZZ AD C Pulley(S3M-35T)
41 NBRGY0131FCZZ AM C Bearing
42 NSFTZ2597FCZZ AE C Fuing drive idle shaft
43 NGERH0111FCWZ AD C Idle gear(24T)
44 NGERH1447FCZ1 AH C Oneway gear(24T)
45 NSFTZ2596FCZZ AG C Ratchet shaft
47 NBLTH0350FCZ1 AH B Belt
DHAI-3640FCZZ AX C Paper exit unit harness [Except AR-M312U,AR-M420U]
49
DHAI-3158FCZZ AQ C Paper exit unit harness [AR-M312U,AR-M420U]
50 MSPRD2859FCZ1 AE C Door switch spring
51 LX-BZ0937FCZZ AB C Screw(3×12)
52 QSW-M0502FCPZ AH B Door switch(AM51632C531N)
53 XEBS730P16000 AA C Screw(3×16)
54 LFRM-1021FCZ1 AL C Paper exit drive frame
55 QEARP0124FCZZ AK C Paper exit earth plate
56 DHAI-3157FCZZ AE C Sensor harness
57 RMOTS0859FCZZ BC B Paper exit motor
58 PSHEZ4914FCZZ AB C Paper exit soundproof sheet
59 PMLT-1276FCZZ AA C Paper exit cushion
60 PSHEP4943FCZZ AB C Reverse gate sheet
61 MSPRD2855FCZZ AB C Paper exit actuator spring
62 PBRSS0208FCZ1 AH B Discharge brush
63 MSPRD2856FCZZ AB C Fusing actuator spring
64 XHBS730P06000 AC C Screw(3×6)
DHAI-3673FCZZ AE C Paper exit earth harness [Except AR-M312U,AR-M420U]
65
DHAI-3333FCZZ AE C Paper exit earth harness [AR-M312U,AR-M420U]
66 PSHEP4962FCZ1 AC C Belt fixing sheet
67 PDUC-0181FCZZ AL D Exhaust duct
68 TLABZ4732FCZZ AF D Arrow label B (U.Kingdom,Europe)
69 XEBS740P12000 AA C Screw(4×12)
(Unit)
Delivery turn over unit(Without No.38,65,68,69) [Except AR-M312U,
CFRM-1020DS52 BU E
901 AR-M420U]
CFRM-1020DS53 BU E Delivery turn over unit(Without No.38,65,68,69) [AR-M312U,AR-M420U]
– 8-1 –
manuals4you.com
8 Delivery turn over unit
1 3
67
3
3
4
62
3
2 3
3
9 3
61
3
65
64 6
57 b
3 58
56 7
58
8 5
3 a
55
10
59
3 60
53
11
54
18 11
19 52
40
17 12
27 47 51 16
50 27 30
19 3 12
26 18 30
3
19 40 30
27 66 49
19 27 19 15 3
18
45
44 19 20 14
19 19
43 18
38
41 42
19
37
19
36
18
18 b
34 63
33 68
58
30 9
18 21
31 19 27 25
30 18
22 69
32 29 28
31 69
35 19
32 24
FCP09288
– 8-2 –
9 MC unit
Inter- PRICE NEW PART Effective
NO. PARTS CODE change RANK MARK RANK DESCRIPTION TR No. time
1 XEBS730P08000 AC C Screw(3×8)
2 PCASZ0295FCZZ AP D MC case
CPLTM6048DS53 AM E Plate [Except AR-M312U,AR-M420U]
3
CPLTM6048DS51 AL E Plate [AR-M312U,AR-M420U]
LHLDZ1621FCZZ AD C MC holder A [Except AR-M312U,AR-M420U]
5
LHLDZ1470FCZZ AD C MC holder A [AR-M312U,AR-M420U]
6 LX-BZ0859FCZZ AC C Screw
7 QSLP-0194FCZZ AC C Terminal
8 QSLP-0195FCZZ AD C Grid terminal
9 LPLTM5873FCZZ AG B Grid
10 LHLDZ1471FCZZ AC C MC holder B
11 CHLDZ1623DS51 AZ E Cleaner holder unit [Except AR-M312U,AR-M420U]
12 PSHEP4911FCZZ AB C MC sheet [AR-M312U,AR-M420U]
(Unit)
CCASZ0295DS52 BC E MC unit [Except AR-M312U,AR-M420U]
901
CCASZ0295DS51 BA E MC unit [AR-M312U,AR-M420U]
9 MC unit
11
1
5 2
6
3
7
8
1
9
12
1
10
FCP09289
– 9-1 –
manuals4you.com
F Process unit[AR-M355N/U,AR-M455N/U,AR-M351N/U,AR-M451N/U]
Inter- PRICE NEW PART Effective
NO. PARTS CODE change RANK MARK RANK DESCRIPTION TR No. time
1 MLEVP0832FCZZ AF C Lever
2 XRESP30-06000 AA C E type ring(E3)
3 NGERH1417FCZZ AC C Paddle gear(14T)
LRALM0180FCZ5 AM C TH rail B [U.kingdom,Europe,Australia,New Zealand]
4
LRALM0180FCZ4 AM C TH rail A [U.S.A,Other Countries]
5 NGERH1612FCZZ AD C Paddle idle gear(14T)
6 XHBS730P08000 AB C Screw(3×8)
7 LPLTM5714FCZZ AB C M3 plate
8 PMLT-1245FCZ2 AE C Process U cushion
9 PCOVP1804FCZZ AG D Process cover U
10 XEBS730P08000 AC C Screw(3×8)
11 XRESP40-06000 AA C E type ring(E4)
12 NBRGP0642FCZZ AE C Waste toner bearing
13 NSRW-0033FCZ1 AC C 2nd Transfer screw
14 PPIPP0206FCZZ AD C Waste toner transfer pipe
16 MSPRC3010FCZ1 AB C Shutter open/close spring
17 PSHT-0088FCZZ AC C Pipe shutter
18 NGERH1369FCZZ AC C Toner transfer gear(30T)
20 NBRGP0771FCPZ AC C Bearing MX
21 NGERH0039QSZZ AE C Transport pipe gear(14T)
24 XBBS730P08000 AA C Screw(3×8)
26 LX-BZ0656FCZ1 AE C Screw
27 PCOVP1803FCZ1 AG C Process cover
28 XRESP50-06000 AA C E type ring(E5)
29 NGERH0038QSZZ AC C Transport pipe gear(15T)
30 NGERH0037QSZZ AC C Idle gear(26T)
32 QEARP0182FCZ1 AD C Process earth plate
33 PSHEZ4827FCZZ AD C Sheet F
34 NSRW-0032FCZZ AG C Transfer screw
35 LPFTF0121FCZZ AE C DSD flange F
36 LPFTF0108FCZZ AK C DSD flange R
37 PSHEZ5335FCZZ AC C Sheet R
38 NROLP1504FCZZ AG C Transfer paddle
39 PMLT-1390FCZZ AC C Handle cushion
40 XEPSD40P12000 AA C Screw(4×12)
41 NCPL-0073FCZZ AD C Waste toner screw coupling
42 CCLEZ0163FC32 AS B Sub blade
44 PTME-0286FCZ1 AH C Separator pawl
45 PRNGF0106FCZ2 AC C Starling N
46 LHLDZ1473FCZZ AC C Separation pawl holder
47 MSPRC2954FCZ2 AB C Separation pawl spring
48 PMLT-1238FCZ1 AC C Toner shield cushion
49 CCLEZ0162FC31 AW B Cleaning blade
51 XBBS230P06000 AD C Screw(3×6)
52 CFRM-1017FC02 AW D Process frame
53 MSPRC2961FCZZ AB C Lever spring
54 NBRGP0654FCZZ AC C Transfer bearing F
55 PSEL-0805FCZZ AE C G seal
56 QEARP0133FCZZ AC C Process earth plate B
57 LX-WZ0440FCZZ AC C Spacer
58 PSPAZ1431FCZZ AA C Spacer A
59 MJNTM0027FCZZ AC C Cleaner joint A
60 MJNTM0028FCZZ AC C Cleaner joint B
61 JHNDP0167FCZ1 AC C MC cleaner handle
62 LPLTM6447FCZZ AE C Frame reinforce plate
63 NSFTZ2884FCZZ BH C Cleaner shaft
64 PSPAP1445FCZZ AC C Reinforce plate spacer
65 XEPS740P10000 AB C Screw(4×10)
66 CPLTM6448FC01 AG C Drum boss fixing plate
501 CHLDZ1473DS55 AK E Separation pawl holder unit
(Unit)
CFRM-1017DS87 BN E Process unit(include 9-901) [U.Kingdom,Europe,Australia,New Zealand]
901
CFRM-1017DS86 BN E Process unit(include 9-901) [U.S.A,Other Countries]
– 10-1 –
F Process unit[AR-M355N/U,AR-M455N/U,AR-M351N/U,AR-M451N/U]
53 10 901
56
41 1
12 4
60
6 10 59
7
42 38 9
10 2 10
3 12 63
7
5
47 45 46 7
501 7
8 11
47 45 46 12
47 45 46 7
44 10
10 37 13
52
501 44 10
47 45 46 501 48
44 10 14
29 6 10
501 51 16
44 10 2
51 7 20 18
30
33 55 20
32 54 21 62 17 27
36 51 28
57 58 40 24
34 64 40
49
40 26
61
FCP09290 24 39
35 66 65
– 10-2 –
manuals4you.com
G Process unit[AR-M312U,AR-M420U]
Inter- PRICE NEW PART Effective
NO. PARTS CODE change RANK MARK RANK DESCRIPTION TR No. time
1 MLEVP0832FCZZ AF C Lever
2 XRESP30-06000 AA C E type ring(E3)
3 NGERH1417FCZZ AC C Paddle gear(14T)
4 LRALM0180FCZ7 AM C TH rail A
5 NGERH1612FCZZ AD C Paddle idle gear(14T)
6 XHBS730P08000 AB C Screw(3×8)
7 LPLTM5714FCZZ AB C M3 plate
8 PMLT-1245FCZ2 AE C Process U cushion
9 PCOVP1589FCZ1 AG C Process cover U
10 XEBS730P08000 AC C Screw(3×8)
11 XRESP40-06000 AA C E type ring(E4)
12 NBRGP0642FCZZ AE C Waste toner bearing
13 NSRW-0033FCZ1 AC C 2nd Transfer screw
14 PPIPP0206FCZZ AD C Waste toner transefer pipe
16 MSPRC3010FCZ1 AB C Shutter open close spring
17 PSHT-0088FCZZ AC C Pipe shutter
18 NGERH1369FCZZ AC C Toner transfer gear(30T)
20 NBRGP0771FCPZ AC C Bearing MX
21 NGERH0039QSZZ AE C Transport pipe gear(14T)
22 MLEVP0782FCBZ AC C Process lever BK
24 XBBS730P08000 AA C Screw(3×8)
26 LX-BZ0656FCP1 AD C Screw
28 XRESP50-06000 AA C E type ring(E5)
29 NGERH0038QSZZ AC C Transport pipe gear(15T)
30 NGERH0037QSZZ AC C Idle gear(26T)
32 QEARP0131FCZZ AD C Process earth plate
33 PSHEZ4827FCZZ AD C Sheet F
34 NSRW-0032FCZZ AG C Transfer screw
35 LPFTF0107FCZZ AK C DSD flange F
36 LPFTF0108FCZZ AK C DSD flange R
37 PSHEZ4828FCZ1 AD C Sheet R
38 NROLP1504FCZZ AG C Transfer paddle
40 XEPS740P12000 AB C Screw(4×12)
41 NCPL-0073FCZZ AD C Waste toner screw coupling
42 CCLEZ0163FC32 AS A Sub blead
44 PTME-0286FCZ1 AH C Separator pawl
45 PRNGF0106FCZ2 AC C Starling N
46 LHLDZ1473FCZZ AC C Separation pawl holder
47 MSPRC2954FCZ2 AB C Separation pawl spring
48 PMLT-1238FCZ1 AC C Toner shield cushion
49 CCLEZ0162FC31 AW A Cleaning blead
51 LX-BZ0047QSZZ AB C Screw(3×6)
52 CFRM-1017FC02 AW C Process frame
53 MSPRC2961FCZZ AB C Lever spring
54 NBRGP0654FCZZ AC C Transfer bearing F
55 PSEL-0805FCZZ AE C G seal
56 QEARP0133FCZZ AC C Process earth plate B
57 LX-WZ0440FCZZ AC C Spacer
58 PSPAZ1431FCZZ AA C Spacer A
59 PSPAZ1432FCZZ AA C Spacer B
62 LPLTM6447FCZZ AE C Frame reinforce plate
64 PSPAP1445FCZZ AC C Reinforce plate spacer
501 CHLDZ1473DS55 AK E Separation pawl holder unit
– 11-1 –
G Process unit[AR-M312U,AR-M420U]
10
53
56
1 59
10
4
41 6
12 7
9
2 10
42 3
12 7
10
47 10 38 5 7
7
47
46 8 11
45 12
44 47 37 7
46
45
44 47 13
501 4546 52
501 44
45
46 48
14
10
501 44 51 29 6 10
501 54 16
49 55
51 7 20 18
30 17
33
20
2
32 58 21 28
36 51
57 64 24
22
34
40 26
62 24
FCP09291 40 24
35
51
– 11-2 –
manuals4you.com
H DV unit[AR-M355N/U,AR-M455N/U,AR-M351N/U,AR-M451N/U]
Inter- PRICE NEW PART Effective
NO. PARTS CODE change RANK MARK RANK DESCRIPTION TR No. time
1 DHAI-3636FCZZ AW C DV harness
2 XBBS730P08000 AA C Screw(3×8)
3 PCOVP1538FCZZ AF C DV R cover
4 XEBS730P08000 AC C Screw(3×8)
5 CPLTM5716FC01 AF C Idle gear fixing plate
6 CGERH1420FC01 AF C Idle gear(29T)
7 XRESP40-06000 AA C E type ring(E4)
8 NGERH1371FCZZ AC C MG gear(22T)
9 XRESP50-06000 AA C E type ring(E5)
10 CHLDZ1445FC02 AK C MG holder R
11 NGERH1374FCZZ AC C MX gear B(31T)
12 NGERH1373FCZZ AD C MX gear A(34T)
13 CBRGP0639FC01 AH C MX bearing
14 XBPSD30P25K00 AA C Screw(3×25K)
15 NROLM1502FCZZ BH B MG roller
16 LPLTM6449FCZZ AT B DV doctor N
17 NROLP1505FCZZ AP C MX roller A
19 JHNDP0166FCBZ AC C SRU handle
20 PCOVP1806FCZ1 AG D DV cover
21 LDAIU0693FCZZ AC C Doctor side block
22 RDTCH0161FCZZ AX B Humidity sensor
25 MLEVP0783FCZZ AD C DV lock lever
26 MSPRC2875FCZZ AC C F handle spring
27 JHNDP0153FCZ5 AE D DV F handle
28 XBBS740P08000 AA C Screw(4×8)
29 LPLTM6022FCZZ AC C M4 plate
35 LPLTM5715FCZZ AC C PP plate
36 CHLDZ1444FC02 AG C MG holder F
37 PBOX-0125FCZ1 AS D DV BOX
38 PSEL-0797FCZZ AC A DV side seal F
39 RDTCT0162FCZZ AZ B ATC sensor
40 XEBS730P06000 AA C Screw(3×6)
41 MSPRD2876FCZZ AC C DV spring
42 MARMP0258FCZZ AD C DV joint arm
43 PSEL-0798FCZZ AC A DV side seal R
44 PCOVP1590FCZZ AE C Bottom cover
46 PMLT-1391FCZZ AF C Cushion
47 PSEL-0800FCZ1 AC C DV seal 2
48 PMLT-1241FCZ1 AA C DV-BOX cushion
49 PMLT-1244FCZ1 AC C Doctor cushion R
50 PTPE-0281FCZZ AA C Doctor suede
53 PCAPH0004YSZZ AC C Cap D
54 XWHSD30-05070 AA C Washer
55 UCLEZ0164FCZZ AG B DV blead
56 PMLT-1296FCZZ AH C Shutter cushion
57 PSHEP5390FCZZ AD C DV sheet
58 PSPAP1447FCZZ AC C DV spacer
(Unit)
901 CBOX-0125DS58 BS E DV unit
– 12-1 –
H DV unit[AR-M355N/U,AR-M455N/U,AR-M351N/U,AR-M451N/U]
28
46
2 20
1
21
50 16
49 19
28
3 7 11
4 7 17
5 12 7
13
6 7
13 14
7
57
55
8 54 15
47
9
10
29 50 b 26
25
21 a
56 27
29
43 37 58 54 28
48
a b
41
22 14
42 13
40
39 29 7
40 38 13
9 53
36
44
48 35 4
FCP09292
– 12-2 –
manuals4you.com
I DV unit[AR-M312U,AR-M420U]
Inter- PRICE NEW PART Effective
NO. PARTS CODE change RANK MARK RANK DESCRIPTION TR No. time
1 DHAI-3148FCZZ AP C DV harness
2 XBBS730P08000 AA C Screw(3×8)
3 PCOVP1538FCZZ AF C DV R cover
4 XEBS730P08000 AC C Screw(3×8)
5 CPLTM5716FC01 AF C Idle gear fixing plate
6 CGERH1420FC01 AF C Idle gear 29T
7 XRESP40-06000 AA C E type ring(E4)
8 NGERH1371FCZZ AC C MG gear(22T)
9 XRESP50-06000 AA C E type ring(E5)
10 CHLDZ1445FC01 AL C MG holder R
11 NGERH1374FCZZ AC C MX gear B(31T)
12 NGERH1373FCZZ AD C MX gear A(34T)
13 CBRGP0639FC01 AH C MX bearing
14 XBPS730P16K00 AB C Screw(3×16K)
15 NROLM1502FCZZ BH C MG roller
16 LPLTM5876FCZZ AS C DV doctor N
17 NROLP1294FCZZ AR C MX roller A
18 NROLP1295FCZZ AR C MX roller B
19 JHNDP0166FCBZ AC C SRU handle
20 PCOVP1592FCZZ AH C DV cover
22 CSHT-0089DS51 BF C DV shutter
23 PCOVP1591FCZZ AE C Shutter cover
24 MSPRD2956FCZZ AB C DV shutter spring
25 MLEVP0783FCZZ AD C DV lock lever
26 MSPRC2875FCZZ AC C F handle spring
27 JHNDP0153FCZZ AE C DV F handle
28 XBBS740P08000 AA C Screw(4×8)
29 LPLTM6022FCZZ AC C M4 plate
32 CPWBF1591FCE1 AL E Initial detect DV PWB unit
35 LPLTM5715FCZZ AC C PP plate
36 CHLDZ1444FC01 AH C MG holder F
37 PBOX-0125FCZ1 AS D DV BOX
38 PSEL-0797FCZZ AC A DV side seal F
39 RDTCT0146FCZZ AX B ATC sensor
40 XEBS730P06000 AA C Screw(3×6)
41 MSPRD2876FCZZ AC C DV spring
42 MARMP0258FCZZ AD C DV joint arm
43 PSEL-0798FCZZ AC A DV side seal R
44 PCOVP1590FCZZ AE C Bottom cover
45 PMLT-1260FCZZ AA C SHT side cushion
46 PMLT-1242FCZZ AG C Cushion
47 PSEL-0800FCZ1 AC C DV seal 2
48 PMLT-1241FCZ1 AA C DV-BOX cushion
49 PMLT-1244FCZ1 AC C Doctor cushion R
50 PSHEZ4882FCZ1 AC C Doctor suede
51 PSHEZ4883FCZZ AE C DV shutter suede N
52 PSHEZ4920FCZZ AA C SHT side sheet
53 PCAPH0004YSZZ AC D Cap D
54 XWHS730-05070 AA C Washer
55 UCLEZ0164FCZZ AG A DV blead
56 PMLT-1296FCZZ AH C Shutter cushion
(Unit)
901 CBOX-0125DS51 BD E DV unit
– 13-1 –
I DV unit[AR-M312U,AR-M420U]
28 45 22 23 46
2 51 20
1
52
16 19
49
18
3 7 11 28
17
4 7 12 7
5 13
6 7 24
13 15
7 14 50 52
45
55
54
8 47
9
10
29 50 b 26
25
a
27
56
29
43 54 28
48
41 b
a
14
42
13
39
40
29 7
38 13
37 9
36 53
44 32
48 35 4 FCP09293
– 13-2 –
manuals4you.com
Update : 2006/05/31
J Controller BOX unit[AR-M355N/U,AR-M455N/U,AR-M351N/U,AR-M451N/U]
Inter- PRICE NEW PART Effective
NO. PARTS CODE change RANK MARK RANK DESCRIPTION TR No. time
1 PDUC-0165FCZ1 AF D Controller duct
2 PFILZ0285FCZ1 AT A Ozone filter
3 XBBS740P08000 AA C Screw(4×8)
4 XEPS740P35000 AC C Screw(4×35)
5 NFANP0076FCZZ AX B Duct fan
6 XHBS740P08000 AA C Screw(4×8)
7 PDUC-0163FCZZ AG D Main duct 2
8 PDUC-0162FCZZ AG D Main duct 1
9 PCOVP1555FCZ1 AE C Controller BOX cover
10 DHAI-3674FCZZ AE C Motor earth harness
11 PBOX-0150FCZZ AS C Controller BOX upper
12 PDUC-0183FCZZ AG D BOX cooling duct R
13 PDUC-0182FCZZ AH D BOX cooling duct lower
14 LPLTM6461FCZZ AF C BOX fan fixing plate
NFANP0073FCZZ BB B Fan motor(12V)
15
NFANP0082FCPZ 1 BF B Fan motor(12V) 06/07 R/C
16 CPWBN1633FCE2 BL E Mother board
17 XBBSD40P30000 AA C Screw(4×30)
18 CBOX-0149FC01 AX D Control box lower
19 LPLTM6458FCZZ AG C Paper exit cabinet fixing plate
20 DHAI-3197FCZZ AE C DSW interface harness
DUNT-7093DS17 CB E LSU unit(35) [AR-M351N/U,AR-M355N/U]
21
DUNT-7093DS18 CB E LSU unit(45) [AR-M451N/U,AR-M455N/U]
22 LX-BZ0964FCZZ AB C Screw
23 LPLTM5769FCZ1 AG C Operation cabinet fixing plate B
24 LPLTM6457FCZZ AT C LSU top plate
25 LX-BZ0921FCZ2 AF C Scanner screw
26 XBPSD25P06000 AA C Screw(2.5×6)
27 PMLT-1397FCZZ AC C Rear duct cushion
28 LPLTM5767FCZ1 AE C Fusing drawer fixing plate
29 DHAI-3642FC11 AX C Fusing interface harness
30 LX-BZ0922FCZZ AC C Screw
31 JHNDP0156FCZZ AE C Handle R
32 PDUC-0164FCZ1 AK C Sub duct
33 QCNCM1001FCZZ AC C Connector(BU04P-TR-PH)
35 LPLTM6465FCZZ AG C Control joint plate
37 PCOVP1560FCZZ AC C FAX I/F cover
39 PCOVP1817FCZZ AC C D/SW cover
40 LX-BZ0026GCZ1 AC C Screw
41 LHLDW1006FCZZ AA C Mini clamp(UAMS-09-0)
42 XHBSD30P06000 AA C Screw(3×6)
43 XEBSD40P10000 AA C Screw(4×10)
44 PSHEP5009FCZZ AC C Control duct sheet A
45 PSHEP4945FCZZ AC C Control duct sheet B
46 PSHEZ4904FCZZ AD C Duct sheet
47 XBPSD30P06000 AA C Screw(3×6)
48 MSPRP3016FCZZ AR C LSU earth plate
DUNT-7314FC12 BK E Soft NIC unit [AR-M351N,AR-M355N,AR-M451N,AR-M455N]
49
PCOVP1557FCZZ AC C LAN/option cover [AR-M351U,AR-M355U,AR-M451U,AR-M455U]
50 XBBSE30P06000 AA C Screw(3×6)
51 XBBSD30P06000 AA C Screw(3×6)
52 PCOVP1629FCZZ AG C Right noise cover
53 DHAI-3673FCZZ AE C Paper exit earth harness
MFP flash ROM A EX(28F322LD4F)
VHI28F322LD4F BE B
[AR-M351N,AR-M355N,AR-M451N,AR-M455N]
54
VHI28F322LD8F BE B MFP flash ROM A EX(28F322LD8F) [AR-M355U,AR-M455U]
VHI28F322LE1F BE B MFP flash ROM A EX(28F322LE1F) [AR-M351U,AR-M451U]
MFP flash ROM B EX(28F322LD5F)
VHI28F322LD5F BE B
[AR-M351N,AR-M355N,AR-M451N,AR-M455N]
55
VHI28F322LD9F BE B MFP flash ROM B EX(28F322LD9F) [AR-M355U,AR-M455U]
VHI28F322LE2F BE B MFP flash ROM B EX(28F322LE2F) [AR-M351U,AR-M451U]
56 LX-BZ0725FCZZ AB C 4/5 adjustment screw
57 RMOTP0910FCPZ BF B Polygon motor
58 PCOVP1814FCZZ AG C Harness protect cover
59 LHLDW1285FCZZ AC C Edge holder(EH11)
60 DHAI-3650FCZZ AR C FM CNT harness
61 LPLTM6464FCZZ AQ C PWB fixing plate
DUNT-7388FCPZ CD E HDD(40GB) [AR-M351N,AR-M355N,AR-M451N,AR-M455N]
62
DUNT-7681FCPZ 1 CD E HDD(40GB) [AR-M351N,AR-M355N,AR-M451N,AR-M455N] 06/04
63 LPLTM6258FCZ2 AE C HDD fixing plate [AR-M351N,AR-M355N,AR-M451N,AR-M455N]
64 LX-BZ1022LCZZ AB C Screw [AR-M351N,AR-M355N,AR-M451N,AR-M455N]
65 PCUSG0378FCZZ AF C Cushion [AR-M351N,AR-M355N,AR-M451N,AR-M455N]
66 CCOVP1815FC01 AP C HDD cover [AR-M351N,AR-M355N,AR-M451N,AR-M455N]
67 JHNDM0177FCZZ AD C HDD handle [AR-M351N,AR-M355N,AR-M451N,AR-M455N]
68 LX-BZ0975FCZZ AC C HDD fixing screw [AR-M351N,AR-M355N,AR-M451N,AR-M455N]
69 CRALM0221FC01 AK C HDD rail F
70 CRALM0222FC01 AK C HDD rail R
– 14-1 –
Update : 2006/05/31
J Controller BOX unit[AR-M355N/U,AR-M455N/U,AR-M351N/U,AR-M451N/U]
Inter- PRICE NEW PART Effective
NO. PARTS CODE change RANK MARK RANK DESCRIPTION TR No. time
71 PFTA-0147FCZZ AF C HDD cover
72 DHAI-3664FC11 AX C Mother PWB interface harness
73 LPLTP6470FCZZ AC C PWB slide lock plate
74 MSPRC3328FCZZ AC C PWB slide spring
75 LX-BZ0266FCZZ AB C Screw
76 QCNW-0225FCZZ AH C Mother interface FFC
77 PSHEZ5339FCZZ AC C BOX interception sheet
78 DHAI-3651FCZZ BC C HDD interface cable
79 PMLT-1369FCZZ AC C HDD core cushion
80 LHLDW1600FCZZ AC C Holder(FCR-60 V0)
81 PDUC-0184FCZZ AH D BOX cooling duct upper
82 PMLT-1394FCZZ AC C Duct between cushion
83 RCORF0046FCZZ AH C Core
84 LRTNP0012FCPZ AD C Retainer
CPLTM6464DS53 CU E Controller unit [AR-M351N,AR-M355N,AR-M451N,AR-M455N]
501 CPLTM6464FC56 - CT E Controller unit [Missing parts code][AR-M355U,R-M455U] 1st lot
CPLTM6464DS56 1 CV E Controller unit [AR-M355U,AR-M455U] 05/03
51 13
47 51 6 6
6
56
37 11
54 6
60
51 3
83 3 3
55 80 3 71
42 67
51 61 42
66 C
69 62
6
70
43 b 65
16 a 64
6 6 6
501 64 68
43 6
65 63
64
74 68 51
32 73 6 18 65
6
77 65 68
41 41
75
83
6 51 68 64
46 41 52
20 c
31 19
24 b 76 72 59
a
22
6 6 23
21 57
48 6 22
84
6 41
42
29
53
28
FCP09294 30 6
– 14-2 –
manuals4you.com
K Controller BOX unit[AR-M312U,AR-M420U]
Inter- PRICE NEW PART Effective
NO. PARTS CODE change RANK MARK RANK DESCRIPTION TR No. time
1 PDUC-0165FCZ1 AF C Controller duct
2 PFILZ0285FCZ1 AT B Ozone filter
3 XBBS740P08000 AA C Screw(4×8)
4 XEPS740P35000 AC C Screw(4×35)
5 NFANP0069FCZZ AV B Fan
6 XHBS740P08000 AA C Screw(4×8)
7 PDUC-0163FCZZ AG C Main duct 2
8 PDUC-0162FCZZ AG C Main duct 1
9 PCOVP1555FCZ1 AE C Controller BOX cover
10 DHAI-3177FCZZ AD C Motor earth harness
11 PBOX-0127FCZ2 AQ D Controller BOX upper
12 NFANP0062FCZZ AX B Fan
13 XBPS740P30000 AB C Screw(4×30)
14 QCNW-0201FCZZ AG C Printer interface FFC
16 CPWBN1460FCE5 AS E Mother board unit
17 LPLTM5758FCZZ AK C M/B fixing plate
18 CBOX-0128FC02 AX E Control box lower
19 LPLTM5768FCZZ AM C Paper exit cabinet fixing plate A
20 DHAI-3197FCZZ AE C DSW interface harness
DUNT-7093DS12 CE E LSU 31 unit [AR-M312U]
21
DUNT-7093DS11 BS E LSU 45 unit [AR-M420U]
22 LX-BZ0964FCZZ AB C Screw
23 LPLTM5769FCZ1 AG C Operation cabinet fixing plate B
24 LPLTM5729FCZZ AT C LSU top plate
25 LX-BZ0921FCZ2 AF C Scanner screw
28 LPLTM5767FCZ1 AE C Fusing drawer fixing plate
29 DHAI-3169FCZZ AT C Fusing interface harness
30 LX-BZ0922FCPZ AC C Screw
31 JHNDP0156FCZZ AE C Handle R
32 PDUC-0164FCZ1 AK C Sub duct
34 CPWBX1645FC51 CM E STD control PWB unit
35 LPLTM5765FCZ4 AG C Control joint plate
41 LHLDW1006FCZZ AA C Mini clamp(UAMS-09-0)
42 XHBS730P06000 AC C Screw(3×6)
43 XEBS740P10000 AA C Screw(4×10)
44 PSHEP5009FCZZ AC C Control duct sheet A
45 PSHEP4945FCZZ AC C Control duct sheet B
46 PSHEZ4904FCZZ AD C Duct sheet
47 XBPS730P06000 AA C Screw(3×6)
48 MSPRP3016FCZZ AR C LSU earth plate
50 XHBS730P06000 AC C Screw(3×6)
51 XBBS730P06000 AC C Screw(3×6)
52 PCOVP1629FCZZ AG C Right noise cover
53 DHAI-3333FCZZ AE C Paper exit earth harness
56 LX-BZ0725FCZZ AB C Handle fixing screw
57 RMOTP0910FCZZ BF B Polygon motor
61 LPLTM5757FCZ1 AP C Control joint plate
62 LRTNP0012FCPZ AD C Retainer
501 CPLTM5757FC66 CN E Controller unit
– 15-1 –
K Controller BOX unit[AR-M312U,AR-M420U]
44 45
1 3
2
3 4
7
8 5 45
3
20 9
3
6
10
a
51 51
11
47 50
56
6
47 25
50 25
6
34
51 51 51 12
56 51 6
35 51 6
51 501 6
13
6 6
42
61 43
6
14
6
42
17
6 6
14
51
6
16
51
6
52
a 6
32 51
18
41
41
31 41 6
6
6
29 19
6
46 22
29
41
57
6 21
6
6 22
6
62
48
23
6
42
28 6 24
53
30 29
FCP09295 6
– 15-2 –
manuals4you.com
L Power supply unit
Inter- PRICE NEW PART Effective
NO. PARTS CODE change RANK MARK RANK DESCRIPTION TR No. time
! AC/DC power supply PWB 100 [100V series]
RDENC0036FCZ3 BX E
[Except AR-M312U,AR-M420U]
! RDENC0020FCZ6 BV E AC/DC power supply PWB 100 [100V series][AR-M312U,AR-M420U]
1
! AC/DC power supply PWB 200 [200V series]
RDENC0037FCZ3 BX E
[Except AR-M312U,AR-M420U]
! RDENC0021FCZ6 BW E AC/DC power supply PWB 200 [200V series][AR-M312U,AR-M420U]
2 CPWBF1558FC32 AZ E Reactor PWB [200V series]
3 XBPS730P08K00 AA C Screw(3×8K)
4 LSUPP0118FCZZ AB C Supporter(SPLSN6) [200V Series]
5 XHBS740P08000 AA C Screw(4×8)
6 LBSHZ1001ACZZ AB C Bushing [200V Series]
7 LPLTM5941FCZZ AF C Filter PWB fixing plate [200V Series]
8 LBSHZ2006SCZZ AB C Bushing(NRP-345) [200V Series]
10 LPLTM5766FCZZ AE C Main switch fixing plate
12 QSW-C1381QCZZ AY B Switch
13 DHAI-3646FCZZ AY C MSW interface harness [Except AR-M312U,AR-M420U]
14 LPLTM5756FCZ1 AP C Power supply unit fixing plate
15 LSUPP0128FCZZ AC C Spacer(L10) [Except AR-M312U,AR-M420U]
16 LPLTM5942FCZ1 AG C Harness protect plate
17 LSUPP0115FCZZ AB C Supporter(SPLSN3) [200V series]
DHAI-3282FCZZ AQ C LSU interface harness [AR-M312U,AR-M420U]
18
DHAI-3638FCZZ AP C LSU interface harness [Except AR-M312U,AR-M420U]
19 XBBS740P08000 AA C Screw(4×8)
DHAI-3665FC12 AY C AC/DC harness 100 [100V Series][Except AR-M312U,AR-M420U]
DHAI-3430FCZZ AW C AC/DC harness 100 [100V Series][AR-M312U,AR-M420U]
20
DHAI-3645FC11 AY C AC/DC harness 200 [200V Series][Except AR-M312U,AR-M420U]
DHAI-3431FCZZ AU C AC/DC harness 200 [200V Series][AR-M312U,AR-M420U]
CPWBF1629FCE1 AY E Relay PWB [100V Series][Except AR-M312U,AR-M420U]
21
CPWBF1629FCE2 AY E Relay PWB [200V Series][Except AR-M312U,AR-M420U]
DHAI-3667FCZZ AE C Filter interface harness [200V Series][Except AR-M312U,AR-M420U]
22
DHAI-3253FCZZ AF C Filter interface harness [200V Series][AR-M312U,AR-M420U]
23 XBPS730P08K00 AA C Screw(3×8S) [Except AR-M312U,AR-M420U]
3
18
20
3 2
20 1
4
4
3
a c 17
16
7
19
m
5
19 8 6 .co
ou
5
10
4y
5
5
als
13
nu
ma
5
5
b
12
14
23
15
15
15
15
21
FCP09296 23
– 16-1 –
Update : 06/02/27
M Rear frame section 1
Inter- PRICE NEW PART Effective
NO. PARTS CODE change RANK MARK RANK DESCRIPTION TR No. time
1 NFANP0069FCZZ AV B Fan
2 XEPS740P35000 AC C Screw(4×35)
3 PDUC-0161FCZ1 AH D Duct
4 XHBS740P06000 AA C Screw(4×6)
5 PSHEZ4874FCZ1 AC C LSU cleaning sheet R
7 PSHEZ4873FCZ1 AC C LSU cleaning sheet F
8 XHBS730P06000 AC C Screw(3×6)
9 DHAI-3236FCZZ AF C DSWF harness
10 QSW-M0502FCPZ AH B Door switch(AM51632C531N)
11 XBBS730P14000 AA C Screw(3×14)
13 LPLTM5775FCZZ AC C Switch fixing plate
14 XHBS730P06000 AC C Screw(3×6)
15 PCOVP1528FCZ2 AK D Front cover right
16 XHBS740P08000 AA C Screw(4×8)
17 PCOVP1529FCZZ AQ D Front cover
18 MSLI-0141FCZZ AS C Slide rail
19 NSFTZ2677FCZZ AL C Fusing guide shaft
20 LX-BZ0817FCZZ AA C Screw
21 MLEVP0780FCZZ AC C DV pressure lever B
23 XRESP30-06000 AA C E type ring(E3)
24 MLEVP0779FCZZ AC C DV pressure lever A
26 PGIDH1883FCZZ AN C DV guide
27 JHNDP0152FCZZ AG C DV guide handle
28 NSFTZ2571FCZZ AE C DV guide shaft
29 MSPRT2834FCZZ AD C DV guide spring
30 LPLTM5710FCZZ AF C DV guide plate
31 NSFTZ2570FCZZ AE C DV shaft
32 LDAIU0623FCZZ AU C Bottom plate
33 LX-BZ0960FCZZ AC C Screw
PCLR-0441FCZZ AK C Collar(φ16)
34
PCLR-0519FCZZ 1 AE C Collar(φ16) 06/05
35 LHLDW1006FCZZ AA C Mini clamp(UAMS-09-0)
36 LRALP0186FCN1 AX D Right rail
37 PSHEZ4885FCZ1 AB C Paper feed base sheet R
39 JHNDP0155FCZZ AF C Handle F
LDAIU0622FCZZ AY C Paper feed base plate
40
LDAIU0622FCZ1 5 AU C Paper feed base plate [Unleaded correspondence][With No.57] 05/09
42 PSHEZ4884FCZZ AF C Paper feed base sheet L
LX-BZ0833FCZZ AC C Screw [Except AR-M312U,AR-M420U]
Screw(4×8) [Productivity improvement][With No.44]
43 XHBS740P08000 5 AA C 05/04
[Except AR-M312U,AR-M420U]
XHBS740P08000 AA C Screw(4×8) [AR-M312U,AR-M420U]
GLEGG0075FCZZ AE D Rubber foot [Except AR-M312U,AR-M420U]
Positioning holder [Productivity improvement][With No.43]
44 LHLDZ1705FCZZ 5 AC D 05/04
[Except AR-M312U,AR-M420U]
LHLDZ1705FCZZ AC D Positioning holder [AR-M312U,AR-M420U]
46 MSPRP2963FCZZ AC C Process earth spring
47 LPLTM5707FCZZ AU C Rear fixing plate
48 LHLDZ1455FCZZ AD C Multi position holder
49 XEBS740P12000 AA C Screw(4×12)
CCASZ0311DS51 AP E Paper powder remove case unit [Except AR-M312U,AR-M420U]
51
CCASZ0296DS51 BA E Paper powder remove case unit [AR-M312U,AR-M420U]
52 XEBS740P10000 AA C Screw(4×10)
53 TCAUS1038FCZZ AD D Laser caution label
54 TLABZ4432FCZZ AC D NO1 label
55 PCOVP1693FCZZ AH C Duct support cover
56 LSTYM0255FCZ1 AL C Duct support plate
LPLTM5708FCZ2 AT C Front fixing plate
57
LPLTM5708FCZ3 5 AR C Front fixing plate [Unleaded correspondence][With No.40] 05/09
58 LRALM0178FCZZ AP C Process rail
59 XHBS740P10000 AA C Screw(4×10)
501 CGIDH1883DS51 BF E DV guide
– 17-1 –
manuals4you.com
Update : 06/02/27
M Rear frame section 1
16
3 2
5
4
16 1
47
7 2
16 16 16
16 1
16 4
55
16 8
48 46
9
56
58 11
53
16 43 44 10
49
44 43 15
13 14
43 16
57 19
16 16
42 16
43 52
16 16
manuals4you.com
16
52 16 17 20
52 40
59
52 18
59
24
52 51
23
21
37 21 24
37 39
16 26
23
21
16 21
23
35 31
29 16
36 30
31 27
501 29 28
34 54
33
32
52
52
52
52
52
FCP09297
– 17-2 –
Update : 06/02/27
N Rear frame section 2
Inter- PRICE NEW PART Effective
NO. PARTS CODE change RANK MARK RANK DESCRIPTION TR No. time
1 MSLI-0141FCZZ AS C Slide rail
2 CPLTM5895FC01 AD C Solenoid fixing plate
3 XBPS720P02500 AA C Screw(2×2.5)
4 MLEVP0831FCZZ AC C Separation pawl lever
5 XRESP40-06000 AA C E type ring(E4)
6 RPLU-0326FCZ2 AN B Separator pawl solenoid
7 LHLDW1006FCZZ AA C Mini clamp(UAMS-09-0)
8 LPLTM5709FCZZ AD C Lift up fixing plate
12 RMOTP0875FCZZ BN B Drum motor
RMOTP0906FCZZ BF B Main motor 35 [AR-M351N/U,AR-M355N/U,AR-M312U]
14
RMOTP0907FCZZ BF B Main motor 45 [AR-M451N/U,AR-M455N/U,AR-M420U]
15 LPLTM5761FCZZ AG C Rear cabinet fixing plate A
16 XHBS740P08000 AA C Screw(4×8)
17 DHAI-3167FCZZ AP C Main drive interface harness
18 MSPRC2962FCZZ AA C Left cabinet spring
19 LX-BZ0932FCPZ AC C Screw
20 NGERH1379FCZZ AC C Lift up gear
21 LDAIU0624FCZZ AG D Lift up base plate
22 RMOTD0858FCPA BS B Lift up motor
23 XEBS730P08000 AC C Screw(3×8)
24 MARMP0252FCZZ AD C Size detect switch arm
25 CPWBF1598FCE1 AG E Cassette detect PWB
CPWBX1637DS60 BX E PCU PWB [AR-355N/U,AR-M351N/U](100V Series)
CPWBX1637FCF0 1 BX N E PCU PWB [AR-355N/U,AR-M351N/U](100V Series) 06/03 R/C
CPWBX1637DS63 BX E PCU PWB [AR-455N/U,AR-M451N/U](100V Series)
CPWBX1637FCF3 1 BX N E PCU PWB [AR-455N/U,AR-M451N/U](100V Series) 06/03 R/C
CPWBX1637DS61 BV E PCU PWB [AR-M351N/U](200V Series)
26
CPWBX1637FCF1 1 CA N E PCU PWB [AR-M351N/U](200V Series) 06/03 R/C
CPWBX1637DS64 BV E PCU PWB [AR-M451N/U](200V Series)
CPWBX1637FCF4 1 CA N E PCU PWB [AR-M451N/U](200V Series) 06/03 R/C
CPWBN1515FCE3 BW E PCU PWB [AR-M312U]
CPWBN1461FCE4 BW E PCU PWB [AR-M420U]
28 DHAI-3635FCPZ AY C DV interface harness
DHAI-3199FCZZ AP C AC harness [Except AR-M312U,AR-M420U]
31
DHAI-3200FCZZ AG C AC harness [AR-M312U,AR-M420U]
32 QSOCA0097FCZZ AN C Outlet connector [AR-M312U,AR-M420U]
33 QSOCA0096FCZZ AK C Inlet(NC-176-1.0)
34 DHAI-3172FCZZ AD C Outlet harness [AR-M312U,AR-M420U]
35 LHLDW1263FCZZ AC C Wire holder(EDS0607M)
LPLTM5760FCZ3 AL C Inlet fixing plate [AR-M312U,AR-M420U]
36
LPLTM6463FCZ1 AM C Inlet fixing plate [Except AR-M312U,AR-M420U]
! CPWBF1626FCE1 AU E Fuse PWB (100V series)
! 38 CPWBF1627FCE2 AW E Fuse PWB (200V series)[Except AR-M312U,AR-M420U]
! CPWBF1641FCE3 AU E Fuse PWB (200V series)[AR-M312U,AR-M420U]
40 LHLDF2330RCZZ AB C PWB holder(LCBS-04N)
! RDENU0038FCZZ BS E High voltage transformer [Except AR-M312U,AR-M420U]
42
! RDENU0022FCZ1 BS E High voltage transformer [AR-M312U,AR-M420U]
43 LHLDZ1449FCZ1 AK D High voltage holder
44 RMOTD0856FCZZ BA B Toner motor
45 MSPRC0024QSZZ AA C Hopper spring
47 NCPL-0045FCZZ AC C Hopper coupling
48 LBSHC0090FCZZ AA C Bushing
49 LPLTM5707FCZZ AU C Rear fixing plate
50 XRESP30-06000 AA C E type ring(E3)
51 MSPRC2644FCZZ AB C Size detect switch spring
52 MSPRC2671FCZZ AB C Lift up gear spring
53 XEBS740P10000 AA C Screw(4×10)
54 QCNW-0205FCZZ AC C HV interface FFC
55 QCNW-0204FCZZ AC C Drum motor interface FFC
56 QCNW-0203FCZZ AD C Main motor interface FFC
57 LPLTM5755FCZZ AR C PCU fixing plate
58 VHI28F081L39F AY B PCU flash ROM(28F081L39) [Except AR-M312U,AR-M420U]
59 XBBS730P06000 AC C Screw(3×6)
60 XBPS730P06K00 AA C Screw(3×6K)
61 DHAI-3831FCZZ AK C Noise earth harness
62 DHAI-3176FCZZ AC C AC earth harness [AR-M312U,AR-M420U]
64 XBPS740P06K00 AA C Screw(4×6K)
65 PCOVP1623FCZZ AD C FAX connector cover [Except AR-M312U,AR-M420U]
66 XHBS730P06000 AC C Screw(3×6)
67 PMLT-1277FCZZ AC C Seal cushion A
68 PMLT-1278FCZZ AD C Seal cushion B
69 DHAI-3144FCZZ AK C Hopper interface harness
70 LX-BZ0901FCPZ AC C Screw
76 PTUBU0134FCZZ AC C Tube
77 DHAI-3647FCZZ AN C Inlet harness
83 RCORF0046FCZZ AH C Core [AR-M312U,AR-M420U]
501 CDAIU0624DS51 BN E Lift up unit
CPLTM6463DS52 BA E Inlet fixing plate unit (100V series)[Except AR-M312U,AR-M420U]
502 CPLTM5760DS59 BB E Inlet fixing plate unit (100V series)[AR-M312U,AR-M420U]
CPLTM6463DS53 BB E Inlet fixing plate unit (200V series)[Except AR-M312U,AR-M420U]
– 18-1 –
manuals4you.com
Update : 06/02/27
N Rear frame section 2
Inter- PRICE NEW PART Effective
NO. PARTS CODE change RANK MARK RANK DESCRIPTION TR No. time
502 CPLTM5760DS60 BC E Inlet fixing plate unit (200V series)[AR-M312U,AR-M420U]
50 c 16
1
8
16
16
16 16
48 53
49 12
47
45
66
16 55
44 f 14
66 16
23 g 15
16 56
h 53
501 18 17
16
43 20 16
50 52 19 16
16
502 54 21
42
34 40 64
40
60
38 61 22
77 58 23
24
59 26
51 25
16
36 16 59
64 69
57 7
64
16 i b
28
83 76 16
62 31 c
59 h f
32
7 g
AR-M312U,AR-M420U 35 76 33 a
59
60 40 64
38 71
77 40 61 502
7
36
64
16
76 31
Except 35
AR-M312U,
AR-M420U 65 66 33 FCP09298
– 18-2 –
O Cassette unit
Inter- PRICE NEW PART Effective
NO. PARTS CODE change RANK MARK RANK DESCRIPTION TR No. time
1 LPLTM5735FCZZ AR C Turn plate
2 MLEVP0754FCZZ AF C Rear plate lever
3 LPLTP5413FCWZ AE C Rear edge plate
4 LHLDW1226FCZZ AB C Turn fastener
5 MSPRC2641FCZ1 AB C Rear plate spring
6 PSHEZ3130FCZZ AB C Rotation plate sheet
7 GCASP0175FCNZ BA D Cassette
8 LHLDZ1377FCZZ AD C Rear plate holder
9 XEBS740P08000 AA C Screw(4×8)
10 PTME-0280FCZZ AD C Cassette pawl right
11 PCOVP1545FCNZ AL D Cassette front cover
12 CPLTM5736FC01 AP C Lift plate
13 XRESP70-08000 AA C E type ring(E7)
14 NGERH1378FCZZ AD C Sector gear
15 LPINS7062SCZZ AA C Pin(3×16)
16 MSPRC2851FCZZ AB C Cassette earth spring
17 MLEVP0755FCZ1 AE C Side plate F lever
18 MSPRC2631FCZZ AC C Side plate F lever spring
19 LPLTP5733FCZZ AH C Side plate F
20 PTPE-0243FCZ1 AC C Side plate tape
21 NGERH0193FCZZ AB C UC manual feed gear
22 LPLTP5734FCZZ AG C Side plate R
23 LX-BZ0884FCPZ AB C Screw
24 PTME-0281FCZZ AD C Cassette pawl left
25 PGIDH1833FCZ1 AC C Side plate guide
Energy star label [U.S.A,CANADA,U.Kingdom,Europe,
TLABZ5148FCZZ AC D
26 Australia,New Zealand]
TLABG0401QSZZ AR D Energy star label [Hong Kong]
(Unit)
901 CCASP0175FC34 BG E Cassette unit(Without No.26)
O Cassette unit
2
20 3
25
22 4
23 5
21
25
20
19
18 1
23
17 21
8
7
9
14 9
16
15
10
9
13
9
12 26 11
24
9
FCP09299
– 19-1 –
manuals4you.com
P Packing material & Accessories[AR-M355N/U,AR-M455N/U,AR-M351N/U,AR-M451N/U]
Inter- PRICE NEW PART Effective
NO. PARTS CODE change RANK MARK RANK DESCRIPTION TR No. time
6 TCADZ1718FCZZ AE D Fusing pressure manual
7 SPAKA6236FCZZ AD D Cassette protect add
8 TCADZ1275FCZZ AB D Cassette rotation tag
9 LHLDW1226FCZZ AB C Turn fastener
! QACCD7912QCPZ AS B AC cord [U.S.A,Canada,LAG2]
! AC cord [U.kingdom,Yemen,Soudi arabia,
QACCB7623QCZZ AQ B
Bahrain,Kuwait,UAE,Oman,Qutar]
! AC cord [Europe,Lebanon,Iran,West africa,Pakistan,
QACCVR621QCPZ AQ B
STCL,Egypt,Jordan,Syria,Tunisia,Morocco]
! QACCLR624QCPZ BA B AC cord [Australia,New Zealand]
! 10 DHAI-3332DS11 BB B AC cord [South africa,India]
! DHAI-3332DS12 BB B AC cord [Israel]
! DHAI-3332DS13 BB B AC cord [Hong kong]
! DHAI-3332DS14 BB B AC cord [Soudi arabia(127V)]
! DHAI-3332DSZZ BB B AC cord [Singapore,Sri Lanka,Indonesia]
! QACCJ6911QCZZ AQ B AC cord [Phillipines]
! QACCR7621QCZZ AZ B AC cord [Argentina]
11 SPAKA6692FCZZ AM D Accessory case
CDSKA0029FC34 AL D CD-ROM
CDSKA0030FC32 BB D CD-ROM [Europe]
CDSKA0030GH31 ∗ N D CD-ROM [Europe]
12
CDSKA0029GH31 ∗ N D CD-ROM [Europe]
CDSKA0042FC31 BB D CD-ROM [Taiwan]
CDSKA0032GH31 ∗ N D CD-ROM(NIC) [AR-M351N,AR-M451N][Europe]
CD-ROM(NIC) [AR-M351N,AR-M355N,AR-M451N,AR-M455N]
CDSKA0032FC31 BH D
[Except Europe]
TCADZ1706FCZZ AE D MSDS card [U.S.A,Canada,U.Kingdom]
14
TCADZ1706GHZZ ∗ N D MSDS card [U.Kingdom]
15 CCADZ1518FC01 AB D Maintenance card EX [Except U.Kingdom]
17 TCADS1511FCZZ AC D Inst.card [Europe(Except U.Kingdom)]
TINSE2880FCZ1 BA D Operation manual (Copy) [English(U.S.A)][AR-M355N/U,AR-M455N/U]
TINSE2882GHZZ ∗ N D Operation manual (Copy) [English(U.Kingdom)][AR-M351N]
TINSE2881FCZ1 BD D Operation manual (Copy) [English(Other)][AR-M351N]
TINSF2884GHZZ ∗ N D Operation manual (Copy) [French][AR-M351N]
TINSG2883GHZZ ∗ N D Operation manual (Copy) [German][AR-M351N]
TINSZ2895GHZZ ∗ N D Operation manual (Copy) [Greek][AR-M351N]
TINSI2886GHZZ ∗ N D Operation manual (Copy) [Italian][AR-M351N]
TINSH2887GHZZ ∗ N D Operation manual (Copy) [Dutch][AR-M351N]
TINSW2888GHZZ ∗ N D Operation manual (Copy) [Swedish][AR-M351N]
TINSZ2889GHZZ ∗ N D Operation manual (Copy) [Norwegian][AR-M351N]
TINSZ2890GHZZ ∗ N D Operation manual (Copy) [Finnish][AR-M351N]
TINSD2891GHZZ ∗ N D Operation manual (Copy) [Danish][AR-M351N]
TINSZ2892GHZZ ∗ N D Operation manual (Copy) [Hungarian][AR-M351N]
TINSZ2893GHZZ ∗ N D Operation manual (Copy) [Czech][AR-M351N]
TINSS2885GHZZ ∗ N D Operation manual (Copy) [Spanish][AR-M351N]
TINSZ2894GHZZ ∗ N D Operation manual (Copy) [Polish][AR-M351N]
TINSR2896GHZZ ∗ N D Operation manual (Copy) [Russian][AR-M351N]
TINSP2897GHZZ ∗ N D Operation manual (Copy) [Portuguese][AR-M351N]
TINSE2899FCZ1 AL D Operation manual (Copy) [English(Hong Kong)][AR-M351U]
TINSE2881FCZ1 BD D Operation manual (Copy) [English(Other)][AR-M351U]
TINSF2884FCZ1 BH D Operation manual (Copy) [French][AR-M351U]
TINSE2902FCZZ AM D Operation manual (Key) [English(U.S.A)][AR-M355N/U,AR-M455N/U]
TINSE2904GHZZ ∗ N D Operation manual (Key) [English(U.Kingdom)][AR-M351N]
TINSE2903FCZZ AT D Operation manual (Key) [English(Other)][AR-M351U/N]
20 TINSF2906GHZZ ∗ N D Operation manual (Key) [French][AR-M351N]
TINSG2905GHZZ ∗ N D Operation manual (Key) [German][AR-M351N]
TINSZ2917GHZZ ∗ N D Operation manual (Key) [Greek][AR-M351N]
TINSI2908GHZZ ∗ N D Operation manual (Key) [Italian][AR-M351N]
TINSS2907GHZZ ∗ N D Operation manual (Key) [Spanish][AR-M351N]
TINSH2909GHZZ ∗ N D Operation manual (Key) [Dutch][AR-M351N]
TINSW2910GHZZ ∗ N D Operation manual (Key) [Swedish][AR-M351N]
TINSZ2911GHZZ ∗ N D Operation manual (Key) [Norwegian][AR-M351N]
TINSZ2912GHZZ ∗ N D Operation manual (Key) [Finnish][AR-M351N]
TINSD2913GHZZ ∗ N D Operation manual (Key) [Danish][AR-M351N]
TINSZ2914GHZZ ∗ N D Operation manual (Key) [Hungarian][AR-M351N]
TINSZ2915GHZZ ∗ N D Operation manual (Key) [Czech][AR-M351N]
TINSZ2916GHZZ ∗ N D Operation manual (Key) [Polish][AR-M351N]
TINSR2918GHZZ ∗ N D Operation manual (Key) [Russian][AR-M351N]
TINSP2919GHZZ ∗ N D Operation manual (Key) [Portuguese][AR-M351N]
TINSF2906FCZZ AT D Operation manual (Key) [French][AR-M351U]
TINSS2907FCZZ BA D Operation manual (Key) [Spanish][AR-M351U]
TINSZ2920FCZZ BA D Operation manual (Key) [Arabic][AR-M351U]
TINSE2840FCZZ AN D Operation manual (PCL inst) [English]
TINSE2840GHZZ ∗ N D Operation manual (PCL inst) [English]
TINSF2842FCZZ BB D Operation manual (PCL inst) [French]
TINSS2843FCZZ BB D Operation manual (PCL inst) [Spanish]
TINSG2841GHZZ ∗ N D Operation manual (PCL inst) [German]
TINSF2842GHZZ ∗ N D Operation manual (PCL inst) [French]
TINSS2843GHZZ ∗ N D Operation manual (PCL inst) [Spanish]
– 20-1 –
P Packing material & Accessories[AR-M355N/U,AR-M455N/U,AR-M351N/U,AR-M451N/U]
Inter- PRICE NEW PART Effective
NO. PARTS CODE change RANK MARK RANK DESCRIPTION TR No. time
TINSI2844GHZZ ∗ N D Operation manual (PCL inst) [Italian]
TINSI2844GHZZ ∗ N D Operation manual (PCL inst) [Italian]
TINSH2845GHZZ ∗ N D Operation manual (PCL inst) [Datch]
TINSW2846GHZZ ∗ N D Operation manual (PCL inst) [Swedish]
TINSZ2847GHZZ ∗ N D Operation manual (PCL inst) [Norwegian]
TINSZ2848GHZZ ∗ N D Operation manual (PCL inst) [Finnish]
TINSD2849GHZZ ∗ N D Operation manual (PCL inst) [Danish]
TINSZ2850GHZZ ∗ N D Operation manual (PCL inst) [Hungarian]
TINSZ2851GHZZ ∗ N D Operation manual (PCL inst) [Czech]
TINSZ2852GHZZ ∗ N D Operation manual (PCL inst) [Polish]
TINSZ2853GHZZ ∗ N D Operation manual (PCL inst) [Greek]
TINSR2854GHZZ ∗ N D Operation manual (PCL inst) [Russian]
TINSP2855GHZZ ∗ N D Operation manual (PCL inst) [Portuguese]
TINSE2858FCZ1 AK D Operation manual (PS inst) [English]
TINSE2858GHZZ ∗ N D Operation manual (PS inst) [English]
TINSF2860FCZ1 BA D Operation manual (PS inst) [French]
20
TINSS2861FCZ1 BA D Operation manual (PS inst) [Spanish]
TINSG2859GHZZ ∗ N D Operation manual (PS inst) [German]
TINSF2860GHZZ ∗ N D Operation manual (PS inst) [French]
TINSS2861GHZZ ∗ N D Operation manual (PS inst) [Spanish]
TINSI2862GHZZ ∗ N D Operation manual (PS inst) [Italian]
TINSH2863GHZZ ∗ N D Operation manual (PS inst) [Dutch]
TINSW2864GHZZ ∗ N D Operation manual (PS inst) [Swedish]
TINSZ2865GHZZ ∗ N D Operation manual (PS inst) [Norwegian]
TINSZ2866GHZZ ∗ N D Operation manual (PS inst) [Finnish]
TINSD2867GHZZ ∗ N D Operation manual (PS inst) [Danish]
TINSZ2868GHZZ ∗ N D Operation manual (PS inst) [Hungarian]
TINSZ2869GHZZ ∗ N D Operation manual (PS inst) [Czech]
TINSZ2870GHZZ ∗ N D Operation manual (PS inst) [Polish]
TINSZ2871GHZZ ∗ N D Operation manual (PS inst) [Greek]
TINSR2872GHZZ ∗ N D Operation manual (PS inst) [Russian]
TINSP2873GHZZ ∗ N D Operation manual (PS inst) [Portuguese]
22 SSAKA2440QCZZ AB D Vinyl bag(280×410mm)
23 SSAKA5003CCZZ AA D Vinyl bag(140×260mm)
25 UBNDA0001FCZZ AA D Band [Except U.S.A,CANADA,LAG2,Philippines]
26 SPAKA6256FCZZ AD D Cabinet protect add
27 SPAKA6265FCZZ AC D Fusing protect add
28 SPAKA6272FCZZ AG D Fusing protect add R
PSHEP5191FCZ1 BF D Key sheet [German]
PSHEP5191FCZZ BF D Key sheet [French]
PSHEP5191FCZ2 BF D Key sheet [Spanish]
PSHEP5191FCZ3 BF D Key sheet [Italian]
PSHEP5191FCZ4 BF D Key sheet [Dutch]
PSHEP5191FCZ5 BF D Key sheet [Swedish]
PSHEP5191FCZ8 BF D Key sheet [Norwegian]
PSHEP5191FCZ9 BF D Key sheet [Finnish]
PSHEP5191FC10 BF D Key sheet [Danish]
PSHEP5191FC13 BF D Key sheet [Hungarian]
PSHEP5191FC11 BF D Key sheet [Czech]
PSHEP5191FC12 BF D Key sheet [Polish]
PSHEP5191FC14 BF D Key sheet [Greek]
PSHEP5191FC16 BF D Key sheet [Russian]
PSHEP5191FC15 BF D Key sheet [Portuguese]
101 PSHEP5350FC20 AR D Key sheet [English]
PSHEP5350FCZ1 AR D Key sheet [German]
PSHEP5350FCZZ AR D Key sheet [French]
PSHEP5350FCZ2 AR D Key sheet [Spanish]
PSHEP5350FCZ3 AR D Key sheet [Italian]
PSHEP5350FCZ4 AR D Key sheet [Dutch]
PSHEP5350FCZ5 AR D Key sheet [Swedish]
PSHEP5350FCZ8 AR D Key sheet [Norwegian]
PSHEP5350FCZ9 AR D Key sheet [Finnish]
PSHEP5350FC10 AR D Key sheet [Danish]
PSHEP5350FC13 AR D Key sheet [Hungarian]
PSHEP5350FC11 AR D Key sheet [Czech]
PSHEP5350FC12 AR D Key sheet [Polish]
PSHEP5350FC14 AR D Key sheet [Greek]
PSHEP5350FC16 AR D Key sheet [Russian]
PSHEP5350FC15 AR D Key sheet [Portuguese]
Dust cover [Egypt,Jordan,Syria,Tunisia,Morocco,Saudi Arabia,
102 GCOVZ0237FCZZ AZ D
Yemen,Bahrain,Kuwait,UAE,Oman,Qutar]
103 TCAUS0009QSZZ AF D LAG plug caution label [Argentina]
12
14
15
17
20
22
11
25
10
23 9
28 7
27
26
FCP09300
– 20-3 –
Q Packing material & Accessories[AR-M312U,AR-M420U]
Inter- PRICE NEW PART Effective
NO. PARTS CODE change RANK MARK RANK DESCRIPTION TR No. time
1 SSAKZ0002QSZZ AF D Vinyl bag
2 CPAKA6127FC01 AF D Packing case lower
6 TCADZ1718FCZZ AE D Fusing pressurization manual
7 SPAKA6236FCZZ AD D Packing add
8 TCADZ1275FCZZ AB D Cassette rotation tag
9 LHLDW1226FCZZ AB C Turn fastener
! QACCVR621QCPZ AQ B AC cord [Iran,Tunisia]
! DHAI-3332DSZZ BB B AC cord [Singapore]
! QACCB7623QCZZ AQ B AC cord [Saudi arabia(250V),Yemen,Bahrain,Kuwait,UAE,Oman,Qutar]
! DHAI-3332DS11 BB B AC cord [South Africa,Sli Lanka,India]
! 10 DHAI-3332DS13 BB B AC cord [Hong kong]
! DHAI-3332DS14 BB B AC cord [Saudi arabia(127V)]
! QACCR7621QCZZ AZ B AC cord [LAG4]
! QACCD7912QCPZ AS B AC cord [LAG2]
! DHAI-3332DS12 BB B AC cord [Special country]
11 SPAKA6235DSZZ AH D Joint
15 CCADZ1518FC01 AB D Maintenance card EX
17 TCADS1511FCZZ AC D Inst.card [Germany,Holland,Sweden]
TINSE3065FCZZ BF D OP manual [English]
TINSE3069FCZZ BF D OP manual [English](Hong Kong)
TINSF3066FCZZ BP D OP manual [French]
20 TINSZ3068FCZZ BP D OP manual [Arabic]
TINSE3071FCZZ AZ D OP manual(Copy) [English]
TINSF3072FCZZ BD D OP manual(Copy) [French]
TINSZ3074FCZZ BD D OP manual(Copy) [Arabic]
22 SSAKA2440QCZZ AB D Vinyl bag(280×410mm)
23 SSAKA5003CCZZ AA D Vinyl bag(140×260mm)
25 UBNDA0001FCZZ AA C Band (200V Series)
26 SPAKA6256FCZZ AD D Cabinet protect add
27 SPAKA6265FCZZ AC D Fusing protect add
28 SPAKA6272FCZZ AG D Fusing protect add R
Dust cover [Tunisia,Saudi Arabia,Yemen,
103 GCOVZ0237FCZZ AZ D
Bahrain,Kuwait,UAE,Oman,Qutar]
105 TCAUS0009QSZZ AF D Plug caution label [LAG4]
15
17 22
20
6 25
10
23
11 7
11 1 9
28 27
2 8
11
26 11
FCP09301
– 21-1 –
manuals4you.com
Update : 06/02/27
R Mother PWB
Inter- PRICE NEW PART Effective
NO. PARTS CODE change RANK MARK RANK DESCRIPTION TR No. time
1 QCNCM1225FCPZ AM C Connector(TX25-80P-LT-H1 E) [CN1]
2 QCNCW1222FCPZ AK C Connector(30pin) [CN2]
3 QCNCM1224FCPZ AF C Connector(B9PS-VH LF) [CN3]
4 QCNCM1223FCPZ AD C Connector(S08B-PASK-2 LF) [CN4]
5 PRDAR0057FCZ1 AS C Heat sink(C16PUG16-30) [IC1]
6 VCEAZA1VW107M AC C Capacitor(35WV 100µF) [C1]
VHDDSM1D1//-1 AB B Diode(DSM1D1) [D1]
8
VHD10JDA10+-1 1 AB B Diode(10JDA10) [D1] 06/05 R/C
9 VHINJM7812A-1 AH B IC(NJM7812A) [IC1]
10 VRS-RE3LA6R2J AC C Resistor(3W 6.2Ω ±5%) [R1]
! 11 QFS-C0048PAZZ AE A Fuse(3.15A) [F1]
! 12 QFS-C0054PAZZ AD A Fuse(6.3A) [F2]
13 QFSHD0002QCZZ AA C Fuse holder(H-0032-2) [F1,F2,F3]
14 RC-EZ0357FCPZ AD C Capacitor(16WV 470µF) [C3,C5,C7,C9,C18]
15 RCNVD0005FCZZ BR B DC-DC Converter[3.3V](MPD6S002T) [IC2]
16 RCNVD0004FCZZ BU B DC-DC Converter[12V](MPD6S009) [IC3]
17 XBBS730P06000 AC C Screw(3×6) [IC1]
18 RC-KZ1054CCN2 AB C Capacitor(50WV 0.1µF) [C11,C12,C13,C14,C15]
20 RCNVD0007FCZZ BS B DC-DC Converter[5V](MPD5S023) [IC4]
! 21 QFS-C0057PAZZ AE A Fuse(800mA) [F3]
(Unit)
901 CPWBN1633FCE2 BL E Mother board
– 22-1 –
Update : 06/02/27
S PCU PWB
Inter- PRICE NEW PART Effective
NO. PARTS CODE change RANK MARK RANK DESCRIPTION TR No. time
1 RFILN0047FCZZ AC C Filter(MMZ1608S121AT) [NF1,NF2,NF5,NF7]
RMPTR4103ACZZ AB B Block resistor(10KΩ×4) [BR18,BR28,BR29,BR30,BR31,BR32]
2
RMPTR4103ACZZ AB B Block resistor(10KΩ×4) [BR2,BR3,BR8,BR9,BR12,BR14,BR16]
RMPTR4330ACZZ AB B Block resistor(33Ω×4) [BR10,BR11,BR13,BR15,BR17]
3
RMPTR4330ACZZ AB B Block resistor(33Ω×4) [BR19,BR24,BR25,BR26,BR27]
4 RMPTR4472ACZZ AB B Block resistor(4.7KΩ×4) [BR1,BR4,BR5,BR7,BR20,BR21,BR22,BR23]
5 VCCCCZ1HH100D AA C Capacitor(50WV 10pF) [C58,C61,C86]
6 VCCCCZ1HH101J AA C Capacitor(50WV 100pF) [C63,C64,C71]
VCKYCZ1CF104Z AB C Capacitor(16WV 0.1µF) [C12,C16,C42,C43,C48,C49,C53]
VCKYCZ1CF104Z AB C Capacitor(16WV 0.1µF) [C55,C62,C72,C74,C76,C81]
VCKYCZ1CF104Z AB C Capacitor(16WV 0.1µF) [C84,C85,C87,C88,C92,C102]
7
VCKYCZ1CF104Z AB C Capacitor(16WV 0.1µF) [C104,C107,C108,C111,C114,C116]
VCKYCZ1CF104Z AB C Capacitor(16WV 0.1µF) [C119,C120,C121,C122,C125,C127]
VCKYCZ1CF104Z AB C Capacitor(16WV 0.1µF) [C133,C134,C137,C142,C145,C157]
8 VCKYCZ1EF223Z AA C Capacitor(25WV 0.022µF) [C69,C75,C82,C93,C109,C117,C118,C143]
VCKYCZ1HB102K AA C Capacitor(50WV 1000pF) [C5,C6,C7,C10,C11,C13,C17]
VCKYCZ1HB102K AA C Capacitor(50WV 1000pF) [C18,C19,C20,C21,C23,C24]
VCKYCZ1HB102K AA C Capacitor(50WV 1000pF) [C25,C26,C27,C28,C29,C30]
VCKYCZ1HB102K AA C Capacitor(50WV 1000pF) [C31,C32,C33,C34,C35,C36]
VCKYCZ1HB102K AA C Capacitor(50WV 1000pF) [C37,C38,C40,C50,C51,C52]
9 VCKYCZ1HB102K AA C Capacitor(50WV 1000pF) [C54,C56,C57,C59,C60,C65]
VCKYCZ1HB102K AA C Capacitor(50WV 1000pF) [C66,C70,C73,C78,C79,C80]
VCKYCZ1HB102K AA C Capacitor(50WV 1000pF) [C83,C89,C94,C95,C97,C98]
VCKYCZ1HB102K AA C Capacitor(50WV 1000pF) [C99,C100,C103,C110,C112,C115]
VCKYCZ1HB102K AA C Capacitor(50WV 1000pF) [C123,C124,C130,C132,C135,C136,C141]
VCKYCZ1HB102K AA C Capacitor(50WV 1000pF) [C146,C147,C150,C151,C153,C154,C39]
10 VCKYTV1CB105K AC C Capacitor(16WV 1µF) [C156]
11 VCKYTV1AB225M AC C Capacitor(10WV 2.2µF) [C155]
12 VCKYCZ1HB222K AA C Capacitor(50WV 2200pF) [C1,C2,C14,C15]
13 VHDDAN202U/-1 AB B Diode(DAN202U) [D11,D13,D19,D31,D33]
14 VHDDAP202U/-1 AB B Diode(DAP202U) [D14,D21]
VHDDA204U//-1 AB B Diode(DA204U) [D7,D8,D9,D10,D12,D15,D16]
15 VHDDA204U//-1 AB B Diode(DA204U) [D17,D18,D20,D22,D23,D24]
VHDDA204U//-1 AB B Diode(DA204U) [D25,D26,D27,D35,D36,D37]
16 VHDMA704A//-1 AC B Diode(MA704A) [D28,D29]
17 VHDCRH01+++-1 AC B Diode(CRH01) [D1,D2,D3,D4,D39]
18 VHI82805GNA-1 BA B IC(D82805GN) [IC17]
21 RH-IX0037QSPZ AQ B SRAM(IS61LV256-15TL) [IC5]
22 VHILM324D++-1 AE B IC(LM324D) [IC24]
23 VHILM339D++-1 AE B IC(LM339D) [IC23,IC25]
24 VHID62503FG-1 AG B IC(D62503FG) [IC6,IC7,IC8,IC13,IC14,IC20,IC21]
25 VHI74VHCT240X AF B IC(74VHCT240X) [IC11]
26 VHI74VHCT244X AF B IC(74VHCT244X) [IC9,IC18]
27 VHVICPS1.2/-1 AF B IC protector(ICPS1.2) [ICP1]
VRS-CZ1JD000J AA C Resistor(1/16W 0Ω ±5%) [R69,R76,R77,R88,R113,R158,R159,R272]
VRS-CZ1JD000J AA C Resistor(1/16W 0Ω ±5%) [Except AR-M455N/U][R62]
VRS-CZ1JD000J AA C Resistor(1/16W 0Ω ±5%) (Except 200V Series)[R125]
28
VRS-CZ1JD000J AA C Resistor(1/16W 0Ω ±5%) [R114]
VRS-CZ1JD000J AA C Resistor(1/16W 0Ω ±5%) [R275,R276]
VRS-CZ1JD000J AA C Resistor(1/16W 0Ω ±5%) [AR-M455N/U][R48]
29 VRS-CZ1JD101J AA C Resistor(1/16W 100Ω ±5%) [R68,R75,R138,R150,R167,R242]
VRS-CZ1JD102J AA C Resistor(1/16W 1.0KΩ ±5%) [R10,R12,R11,R26,R27,R59,R60]
VRS-CZ1JD102J AA C Resistor(1/16W 1.0KΩ ±5%) [R61,R81,R82,R83,R84,R105,R107]
30 VRS-CZ1JD102J AA C Resistor(1/16W 1.0KΩ ±5%) [R109,R121,R135,R148,R160,R163,R165]
VRS-CZ1JD102J AA C Resistor(1/16W 1.0KΩ ±5%) [R177,R233,R261,R262,R263,R264]
VRS-CZ1JD102J AA C Resistor(1/16W 1.0KΩ ±5%) (200V Series)[R155]
31 VRS-CZ1JD102F AA C Resistor(1/16W 1KΩ ±1%) [R182]
32 VRS-CZ1JD103F AA C Resistor(1/16W 10KΩ ±1%) [R206,R212,R252,R253,R268]
VRS-CZ1JD103J AA C Resistor(1/16W 10KΩ ±5%) [R19,R20,R21,R22,R23,R28,R29]
33
VRS-CZ1JD103J AA C Resistor(1/16W 10KΩ ±5%) [R30,R31,R32,R33,R34,R35,R36]
VRS-CZ1JD103J AA C Resistor(1/16W 10KΩ ±5%) [R37,R38,R39,R40,R41,R46,R47]
VRS-CZ1JD103J AA C Resistor(1/16W 10KΩ ±5%) [R55,R56,R63,R71,R73,R78,R80]
VRS-CZ1JD103J AA C Resistor(1/16W 10KΩ ±5%) [R91,R92,R93,R95,R96,R99,R100]
VRS-CZ1JD103J AA C Resistor(1/16W 10KΩ ±5%) [R101,R103,R104,R106,R108,R111]
VRS-CZ1JD103J AA C Resistor(1/16W 10KΩ ±5%) [R116,R117,R118,R119,R122,R123]
VRS-CZ1JD103J AA C Resistor(1/16W 10KΩ ±5%) [R124,R126,R127,R128,R133,R134]
VRS-CZ1JD103J AA C Resistor(1/16W 10KΩ ±5%) [R139,R140,R141,R146,R147,R149]
33
VRS-CZ1JD103J AA C Resistor(1/16W 10KΩ ±5%) [R151,R152,R153,R154,R157,R162]
VRS-CZ1JD103J AA C Resistor(1/16W 10KΩ ±5%) [R168,R169,R172,R173,R178,R183]
VRS-CZ1JD103J AA C Resistor(1/16W 10KΩ ±5%) [R184,R185,R186,R187,R188,R189]
VRS-CZ1JD103J AA C Resistor(1/16W 10KΩ ±5%) [R190,R191,R192,R194,R196,R211]
VRS-CZ1JD103J AA C Resistor(1/16W 10KΩ ±5%) [R213,R214,R221,R222,R223,R224]
VRS-CZ1JD103J AA C Resistor(1/16W 10KΩ ±5%) [R225,R229,R235,R236,R237,R239]
VRS-CZ1JD103J AA C Resistor(1/16W 10KΩ ±5%) [R243,R250,R251,R269]
34 VRS-CZ1JD104J AA C Resistor(1/16W 100KΩ ±5%) [R210,R255,R256,R257,R258,R259,R260]
35 VRS-CZ1JD105J AA C Resistor(1/16W 1.0MΩ ±5%) [R74,R240]
36 VRS-CZ1JD106J AA C Resistor(1/16W 10MΩ ±5%) [R16]
37 VRS-CZ1JD152F AA C Resistor(1/16W 1.5KΩ ±1%) [R179,R208,R254]
38 VRS-CZ1JD162J AA C Resistor(1/16W 1.6KΩ ±5%) [R24]
39 VRS-CZ1JD153F AB C Resistor(1/16W 15KΩ ±1%) [R171,R180]
– 23-1 –
manuals4you.com
Update : 06/02/27
S PCU PWB
Inter- PRICE NEW PART Effective
NO. PARTS CODE change RANK MARK RANK DESCRIPTION TR No. time
40 VRS-CZ1JD201J AA C Resistor(1/16W 200Ω ±5%) [R25,R170]
41 VRS-CZ1JD202F AA C Resistor(1/16W 2KΩ ±1%) [R207]
42 VRS-CZ1JD203J AA C Resistor(1/16W 20KΩ ±5%) [R66,R120]
45 VRS-CZ1JD302J AA C Resistor(1/16W 3KΩ ±5%) [R1,R132,R193,R195]
46 VRS-CZ1JD304F AA C Resistor(1/16W 300KΩ ±1%) [R247,R249]
47 VRS-CZ1JD330J AA C Resistor(1/16W 33Ω ±5%) [R64,R94,R110]
48 VRS-CZ1JD471J AA C Resistor(1/16W 470Ω ±5%) [R17,R18,R67]
VRS-CZ1JD472F AA C Resistor(1/16W 4.7KΩ ±1%) [R181,R238,R244]
49
VRS-CZ1JD472F AA C Resistor(1/16W 4.7KΩ ±1%) [R215,R218]
VRS-CZ1JD472J AA C Resistor(1/16W 4.7KΩ ±5%) [R4,R5,R51,R52,R53,R72,R85]
50 VRS-CZ1JD472J AA C Resistor(1/16W 4.7KΩ ±5%) [R86,R87,R90,R112,R129,R130]
VRS-CZ1JD472J AA C Resistor(1/16W 4.7KΩ ±5%) [R164,R166,R227,R228,R232,R234]
VRS-CZ1JD473F AA C Resistor(1/16W 47KΩ ±1%) [R205]
51
VRS-CZ1JD473F AA C Resistor(1/16W 47KΩ ±1%) [R174,R175]
VRS-CZ1JD473J AA C Resistor(1/16W 47KΩ ±5%) [R2,R49,R57,R65,R79,R142]
52
VRS-CZ1JD473J AA C Resistor(1/16W 47KΩ ±5%) [R143,R144,R145,R265]
53 VRS-CZ1JD474J AA C Resistor(1/16W 470KΩ ±5%) [R241]
54 VRS-CZ1JD562J AA C Resistor(1/16W 5.6KΩ ±5%) [R176]
55 VRS-CZ1JD621F AA C Resistor(1/16W 620Ω ±1%) [R246,R248]
56 VRS-CZ1JD680J AA C Resistor(1/16W 68Ω ±5%) [R115]
57 VRS-CZ1JD681F AA C Resistor(1/16W 680Ω ±1%) [R217,R220]
58 VRS-CZ1JD752J AA C Resistor(1/16W 7.5KΩ ±5%) [R6,R7]
59 VRS-CZ1JD822F AA C Resistor(1/16W 8.2KΩ ±1%) [R216,R219]
60 VSDTA143ZUA-1 AB B Transistor(DTA143ZUA) [Q16]
VSDTC143ZUA-1 AC B Transistor(DTC143ZUA) [Q1,Q4,Q6,Q8,Q11,Q12]
61
VSDTC143ZUA-1 AC B Transistor(DTC143ZUA) [Q15,Q18,Q22,Q24,Q25]
62 VSDTC114EUA-1 AC B Transistor(DTC114EUA) [Q9,Q10,Q17,Q21,Q23]
63 VS2SK3018++-1 AC B Transistor(2SK3018) [Q2,Q5,Q7,Q19,Q20]
64 VS2SB1197KR-1 AC B Transistor(2SB1197K) [Q13,Q14]
65 VS2SD1898//-1 AD B Transistor(2SD1898) [Q3]
67 RFILN0062FCPZ AC C Filter(ZJSR5101-102) [NF3,NF4,NF6,NF8]
72 VCEASM1HM335M AB C Capacitor(50WV 3.3µF) [C149]
76 VCQYNA1HM103K AA C Capacitor(50WV 0.010µF) [C129]
77 VHPLT1D67A/-1 AC B LED(LT1D67A) [LED1]
78 QSOCZ0002QSPZ AC C Socket(8pin) [For IC4]
79 QSOCZ0095FCPZ AR C IC Socket(179707-1) [SOCKET1]
80 VHDRLS73///-1 AA B Diode(RLS73) [D5,D6,D30,D32,D34,D38]
81 VHDRLS73///-1 AA B Diode(RLS73) [D40]
83 VHERD22FB//-1 AD B Zener diode(RD22FB) [ZD1,ZD3]
84 VHIC24WC08L-1 AF B IC(C24WC08L) [IC4]
85 VHIMTD13611-1 AR B IC(MTD1361-4101) [IC3]
86 VHINJM7805A-1 AH B IC(NJM7805A) [IC22]
87 VHIBD45271G-1 AD B IC(BD45271G) [IC15]
88 VHITA7291AS-1 AF B IC(TA7291S) [IC1,IC16]
89 VHITD62003AP1 AG B IC(TD620003AP1) [IC2,IC26]
90 VRS-TP2BD101J AA C Resistor(1/8W 100Ω ±5%) [R231,R230]
91 VRS-TP2BD122J AA C Resistor(1/8W 1.2KΩ ±5%) [R8,R9,R13,R14]
92 VRS-TP2BD151J AA C Resistor(1/8W 150Ω ±5%) [R50,R54,R58]
93 VRS-TP2BD152J AA C Resistor(1/8W 1.5KΩ ±5%) [R209]
94 VRS-TP2BD472J AA C Resistor(1/8W 4.7KΩ ±5%) [R277]
95 VRS-TP2BD391J AA C Resistor(1/8W 390Ω ±5%) [R279,R280,R281]
96 VRS-RE3AA241J AC C Resistor(1W 240Ω ±5%) [R226]
97 VRS-RE3DA1R0J AB C Resistor(2W 1.0Ω ±5%) [R42,R43]
98 QCNCM0671FCZZ AE C Connector(9pin) [CN17]
99 QCNCM0878FCZZ AF C Connector(30pin) [CN12]
100 QCNCM0923FC24 AF C Connector(24pin) [CN13]
101 QCNCM0923FC32 AG C Connector(32pin) [CN4]
102 QCNCM1143FCZZ AG C Connector(22pin) [CN11]
103 QCNCM1144FCZZ AH C Connector(24pin) [CN10]
104 QCNCM2654SCZZ AF C Connector(32pin) [CN16]
105 QCNCM2401SC0H AC C Connector(8pin) [CN21]
106 QCNCM5093SC0B AB C Connector(2pin) [CN7,CN22,CN23]
107 QCNCM7014SC0H AB C Connector(8pin) [CN5]
108 QCNCM7014SC1A AC C Connector(11pin) [CN8]
109 QCNCM7014SC1F AD C Connector(16pin) [CN14]
110 QCNCW0002ESZZ AC C Connector(8pin) [CN9]
111 QCNCW1136FCZZ AC C Connector(8pin) [CN6]
112 QCNCW1139FCZZ AC C Connector(14pin) [CN15]
113 QCNCW1222FCPZ AK C Connector(30pin) [CN2]
114 QCNCW0090QSZZ AE C Connector(24pin) [CN3]
115 RCRSZ0001QSZZ AG B Crystal(AT-51 19.6608MHz) [X1]
116 RCRUB0002FCZZ AP B Crystal(31.554MHz) [Except AR-M451N/U,AR-M455N/U][X2]
117 RCRUB0001FCZZ AP B Crystal(31.554MHz) [AR-M451N/U,AR-M455N/U][X2]
(Unit)
CPWBX1637DS60 BX E PCU PWB [AR-355N/U,AR-M351N/U](100V Series)
CPWBX1637FCF0 1 BX N E PCU PWB [AR-355N/U,AR-M351N/U](100V Series) 06/03 R/C
CPWBX1637DS63 BX E PCU PWB [AR-M455N/U,AR-M451N/U](100V Series)
901
CPWBX1637FCF3 1 BX N E PCU PWB [AR-M455N/U,AR-M451N/U](100V Series) 06/03 R/C
CPWBX1637DS61 BV E PCU PWB [AR-M351N/U](200V Series)
CPWBX1637FCF1 1 CA N E PCU PWB [AR-M351N/U](200V Series) 06/03 R/C
– 23-2 –
Update : 06/02/27
S PCU PWB
Inter- PRICE NEW PART Effective
NO. PARTS CODE change RANK MARK RANK DESCRIPTION TR No. time
CPWBX1637DS64 BV E PCU PWB [AR-M451N/U](200V Series)
901
CPWBX1637FCF4 1 CA N E PCU PWB [AR-M451N/U](200V Series) 06/03 R/C
– 23-3 –
manuals4you.com
T MFP control PWB
Inter- PRICE NEW PART Effective
NO. PARTS CODE change RANK MARK RANK DESCRIPTION TR No. time
RMPTR4103ACZZ AB B Block resistor(10KΩ×4) [BR1,BR2,BR3,BR4,BR5,BR14]
RMPTR4103ACZZ AB B Block resistor(10KΩ×4) [BR27,BR30,BR31,BR32,BR74]
RMPTR4103ACZZ AB B Block resistor(10KΩ×4) [BR76,BR78,BR80,BR93,BR94]
RMPTR4103ACZZ AB B Block resistor(10KΩ×4) [BR95,BR96,BR97,BR98,BR99]
1
RMPTR4103ACZZ AB B Block resistor(10KΩ×4) [BR100,BR101,BR713,BR714]
RMPTR4103ACZZ AB B Block resistor(10KΩ×4) [BR721,BR722,BR725,BR726]
RMPTR4103ACZZ AB B Block resistor(10KΩ×4) [BR727,BR728,BR729,BR730]
RMPTR4103ACZZ AB B Block resistor(10KΩ×4) [BR731,BR732]
RMPTR4100ACZZ AB B Block resistor(10Ω×4) [BR6,BR10,BR16,BR17,BR20]
2 RMPTR4100ACZZ AB B Block resistor(10Ω×4) [BR58,BR59,BR60,BR61]
RMPTR4100ACZZ AB B Block resistor(10Ω×4) [BR705,BR706]
RMPTR4330ACZZ AB B Block resistor(33Ω×4) [BR8,BR9,BR11,BR12,BR13]
RMPTR4330ACZZ AB B Block resistor(33Ω×4) [BR15,BR19,BR21,BR22,BR23]
RMPTR4330ACZZ AB B Block resistor(33Ω×4) [BR24,BR25,BR28,BR29,BR33]
RMPTR4330ACZZ AB B Block resistor(33Ω×4) [BR34,BR35,BR36,BR37,BR38]
RMPTR4330ACZZ AB B Block resistor(33Ω×4) [BR39,BR40,BR41,BR43,BR44]
RMPTR4330ACZZ AB B Block resistor(33Ω×4) [BR47,BR49,BR50,BR51,BR53]
RMPTR4330ACZZ AB B Block resistor(33Ω×4) [BR54,BR55,BR56,BR57,BR62]
RMPTR4330ACZZ AB B Block resistor(33Ω×4) [BR63,BR64,BR65,BR66,BR67]
3 RMPTR4330ACZZ AB B Block resistor(33Ω×4) [BR68,BR69,BR70,BR71,BR72]
RMPTR4330ACZZ AB B Block resistor(33Ω×4) [BR73,BR75,BR77,BR79]
RMPTR4330ACZZ AB B Block resistor(33Ω×4) [BR102,BR103,BR104,BR105]
RMPTR4330ACZZ AB B Block resistor(33Ω×4) [BR106,BR107,BR108,BR109]
RMPTR4330ACZZ AB B Block resistor(33Ω×4) [BR707,BR708,BR709,BR710]
RMPTR4330ACZZ AB B Block resistor(33Ω×4) [BR711,BR712,BR715,BR716]
RMPTR4330ACZZ AB B Block resistor(33Ω×4) [BR717,BR718,BR719,BR720]
RMPTR4330ACZZ AB B Block resistor(33Ω×4) [BR723,BR724,BR734,BR735]
RMPTR4330ACZZ AB B Block resistor(33Ω×4) [BR736,BR737,BR738]
4 RMPTR4472ACZZ AB B Block resistor(4.7KΩ×4) [BR700,BR702,BR703]
5 RMPTR4391ACZZ AA B Block resistor(390Ω×4) [BR704]
6 RMPTR4332ACZZ AA B Block resistor(3.3KΩ×4) [BR733]
! 7 UBATL0017FCZZ AL B Battery(CR2450) [BT1]
8 QSOCZ0091FCZZ AL C Battery Holder(HL-50A) [BT1]
9 PCOVP1782FCZZ AC D Battery Cover [BT1]
10 QSOCN0100FCPZ AH C Connector(P1284)(57RE-40360-830B) [CN1]
11 QSOCZ0007QSPA AP C Connector(SO-DIMM)(DM-3D4-B3210(LF)) [CN3]
12 QSOCZ0094FCPA AL C Connector(FLASH ROM)(DMM2-SD72AR-113-F) [CN4,CN5,CN6]
14 QCNCW7040XCPZ AN C Connector(Mother CN)(TX24-80R-LT-H1(LF)) [CN8]
15 QCNCM1183FCPZ AM C Connector(Soft NIC)(100P15.2-JXKS-GB(LF)) [CN9]
16 QCNCM1227FCPZ AL C Connector(RIC)(HIF3FC-10PA-2.54DSA(71)) [CN14]
17 QCNCM1182FCPZ AM C Connector(FAX I/F)(100P9.2-JXKS-GB(LF)) [CN16]
18 QSOCN0003ESPZ AG C Connector(USB)(DUSB-BRA42-T11(D4T)-FA) [CN700]
19 QCNCM1314FCPZ AL C Connector(HDD)(RA-H401TD-1190(LF)) [CN701]
20 QCNCW1149FCZZ AN C Connector(Scanner)(8AL068S-305C3) [CN702]
VCCCCZ1HH101J AA C Capacitor(50WV 100pF) [C7,C8,C10,C17,C18,C20]
VCCCCZ1HH101J AA C Capacitor(50WV 100pF) [C22,C30,C33,C35,C38,C39]
21 VCCCCZ1HH101J AA C Capacitor(50WV 100pF) [C40,C43,C47,C48,C51,C184]
VCCCCZ1HH101J AA C Capacitor(50WV 100pF) [C339,C340,C341,C965]
VCCCCZ1HH101J AA C Capacitor(50WV 100pF) [C1004,C1005,C1006,C1007]
VCKYCZ1CF104Z AB C Capacitor(16WV 0.1µF) [C9,C11,C12,C13,C14,C23]
VCKYCZ1CF104Z AB C Capacitor(16WV 0.1µF) [C24,C31,C32,C37,C41,C42]
VCKYCZ1CF104Z AB C Capacitor(16WV 0.1µF) [C44,C45,C53,C54,C55,C56]
VCKYCZ1CF104Z AB C Capacitor(16WV 0.1µF) [C58,C66,C77]
VCKYCZ1CF104Z AB C Capacitor(16WV 0.1µF) [C85,C86,C87,C88,C93,C96]
VCKYCZ1CF104Z AB C Capacitor(16WV 0.1µF) [C97,C98,C100,C103,C104]
VCKYCZ1CF104Z AB C Capacitor(16WV 0.1µF) [C105,C106,C113,C117,C118]
VCKYCZ1CF104Z AB C Capacitor(16WV 0.1µF) [C120,C123,C124,C126,C127]
VCKYCZ1CF104Z AB C Capacitor(16WV 0.1µF) [C128,C131,C132,C134,C135]
VCKYCZ1CF104Z AB C Capacitor(16WV 0.1µF) [C137,C140,C141,C142,C143]
VCKYCZ1CF104Z AB C Capacitor(16WV 0.1µF) [C145,C149,C153,C154,C155]
VCKYCZ1CF104Z AB C Capacitor(16WV 0.1µF) [C156,C157,C158,C159,C160]
VCKYCZ1CF104Z AB C Capacitor(16WV 0.1µF) [C161,C162,C163,C164,C172]
VCKYCZ1CF104Z AB C Capacitor(16WV 0.1µF) [C173,C177,C182,C183,C186]
VCKYCZ1CF104Z AB C Capacitor(16WV 0.1µF) [C187,C189,C190,C191,C192]
22
VCKYCZ1CF104Z AB C Capacitor(16WV 0.1µF) [C194,C195,C196,C197,C198]
VCKYCZ1CF104Z AB C Capacitor(16WV 0.1µF) [C199,C201,C202,C204,C210]
VCKYCZ1CF104Z AB C Capacitor(16WV 0.1µF) [C211,C212,C215,C216,C217]
VCKYCZ1CF104Z AB C Capacitor(16WV 0.1µF) [C219,C221,C222,C235,C236]
VCKYCZ1CF104Z AB C Capacitor(16WV 0.1µF) [C237,C238,C239,C240,C241]
VCKYCZ1CF104Z AB C Capacitor(16WV 0.1µF) [C242,C243,C244,C245,C246]
VCKYCZ1CF104Z AB C Capacitor(16WV 0.1µF) [C247,C248,C249,C250,C251]
VCKYCZ1CF104Z AB C Capacitor(16WV 0.1µF) [C252,C253,C254,C255,C256]
VCKYCZ1CF104Z AB C Capacitor(16WV 0.1µF) [C257,C258,C259,C260,C261]
VCKYCZ1CF104Z AB C Capacitor(16WV 0.1µF) [C262,C278,C279,C297,C298]
VCKYCZ1CF104Z AB C Capacitor(16WV 0.1µF) [C299,C300,C355,C356,C357]
VCKYCZ1CF104Z AB C Capacitor(16WV 0.1µF) [C358,C359,C360,C361,C362]
VCKYCZ1CF104Z AB C Capacitor(16WV 0.1µF) [C707,C708,C709,C710,C715]
VCKYCZ1CF104Z AB C Capacitor(16WV 0.1µF) [C716,C717,C718,C720,C723]
VCKYCZ1CF104Z AB C Capacitor(16WV 0.1µF) [C726,C728,C729,C730,C738]
– 24-1 –
T MFP control PWB
Inter- PRICE NEW PART Effective
NO. PARTS CODE change RANK MARK RANK DESCRIPTION TR No. time
VCKYCZ1CF104Z AB C Capacitor(16WV 0.1µF) [C739,C740,C741,C742,C745]
VCKYCZ1CF104Z AB C Capacitor(16WV 0.1µF) [C746,C747,C748,C749,C750]
VCKYCZ1CF104Z AB C Capacitor(16WV 0.1µF) [C751,C770,C771,C772,C773]
VCKYCZ1CF104Z AB C Capacitor(16WV 0.1µF) [C774,C775,C776,C777,C778]
VCKYCZ1CF104Z AB C Capacitor(16WV 0.1µF) [C779,C781,C783,C784,C785]
VCKYCZ1CF104Z AB C Capacitor(16WV 0.1µF) [C786,C787,C788,C789,C790]
VCKYCZ1CF104Z AB C Capacitor(16WV 0.1µF) [C791,C792,C793,C794,C795]
VCKYCZ1CF104Z AB C Capacitor(16WV 0.1µF) [C796,C797,C798,C799,C800]
VCKYCZ1CF104Z AB C Capacitor(16WV 0.1µF) [C845,C847,C849,C852,C854]
VCKYCZ1CF104Z AB C Capacitor(16WV 0.1µF) [C857,C859,C863,C866,C868]
22
VCKYCZ1CF104Z AB C Capacitor(16WV 0.1µF) [C875,C877,C880,C882,C884]
VCKYCZ1CF104Z AB C Capacitor(16WV 0.1µF) [C886,C887,C888,C889,C890]
VCKYCZ1CF104Z AB C Capacitor(16WV 0.1µF) [C891,C892,C893,C910,C911]
VCKYCZ1CF104Z AB C Capacitor(16WV 0.1µF) [C920,C921,C930,C931,C932]
VCKYCZ1CF104Z AB C Capacitor(16WV 0.1µF) [C933,C934,C935,C936,C937]
VCKYCZ1CF104Z AB C Capacitor(16WV 0.1µF) [C938,C942,C943,C944]
VCKYCZ1CF104Z AB C Capacitor(16WV 0.1µF) [C1010,C1034]
VCKYCZ1CF104Z AB C Capacitor(16WV 0.1µF) [C1035,C1036,C1037,C1038]
VCKYCZ1CF104Z AB C Capacitor(16WV 0.1µF) [C1039,C1040,C1041,C1050]
VCKYCZ1CF104Z AB C Capacitor(16WV 0.1µF) [C1051,C1052,C1055]
VCEASX1CN226M AC C Capacitor(16WV 22µF) [C57,C64,C90,C114,C115]
VCEASX1CN226M AC C Capacitor(16WV 22µF) [C136,C719,C722,C725,C736]
23
VCEASX1CN226M AC C Capacitor(16WV 22µF) [C737,C743,C744,C848,C855]
VCEASX1CN226M AC C Capacitor(16WV 22µF) [C862,C869,C878,C885]
24 VCCCCZ1HH220J AA C Capacitor(50WV 22pF) [C61,C700,C701]
VCEASX1CN106M AC C Capacitor(16WV 10µF) [C94,C166,C179,C223,C711]
25 VCEASX1CN106M AC C Capacitor(16WV 10µF) [C712,C713,C714,C780,C952]
VCEASX1CN106M AC C Capacitor(16WV 10µF) [C1030,C1042]
VCEASX1CN476M AC C Capacitor(16WV 47µF) [C167,C168,C311,C966]
26
VCEASX1CN476M AC C Capacitor(16WV 47µF) [C1008,C1032,C1033]
27 VCKYCY1EB104K AG C Capacitor(25WV 0.1µF) [C181,C188,C205,C206,C1061]
VCKYCZ1HB102K AA C Capacitor(50WV 1000pF) [C200,C203,C721,C724,C727]
VCKYCZ1HB102K AA C Capacitor(50WV 1000pF) [C734,C735,C782,C973,C974]
VCKYCZ1HB102K AA C Capacitor(50WV 1000pF) [C975,C976,C977,C978,C982]
28
VCKYCZ1HB102K AA C Capacitor(50WV 1000pF) [C984,C985,C987,C988,C991]
VCKYCZ1HB102K AA C Capacitor(50WV 1000pF) [C992,C997,C998,C1003]
VCKYCZ1HB102K AA C Capacitor(50WV 1000pF) [C1029]
29 VCKYTQ0JB106K AE C Capacitor(6.3WV 10µF) [C332,C834]
30 RC-KZ1012ACZZ AC C Capacitor(10WV 10µF) [C326]
31 RC-EZ0357FCPZ AD C Capacitor(16WV 470µF) [C331,C343,C833,C1009]
VCKYCZ1HF103Z AA C Capacitor(50WV 0.01µF) [C844,C846,C850,C851,C853]
32 VCKYCZ1HF103Z AA C Capacitor(50WV 0.01µF) [C856,C858,C864,C865,C867]
VCKYCZ1HF103Z AA C Capacitor(50WV 0.01µF) [C874,C876,C879,C881,C883]
VCCCCZ1HH100D AA C Capacitor(50WV 10pF) [C344,C345,C894,C895,C896]
VCCCCZ1HH100D AA C Capacitor(50WV 10pF) [C897,C898,C899,C900,C901]
VCCCCZ1HH100D AA C Capacitor(50WV 10pF) [C902,C903,C904,C905,C906]
33 VCCCCZ1HH100D AA C Capacitor(50WV 10pF) [C907,C908,C909,C912,C913]
VCCCCZ1HH100D AA C Capacitor(50WV 10pF) [C914,C915,C916,C917,C918]
VCCCCZ1HH100D AA C Capacitor(50WV 10pF) [C919,C922,C923,C924,C925]
VCCCCZ1HH100D AA C Capacitor(50WV 10pF) [C926,C927,C928,C929]
34 VCEASX1VN106M AC C Capacitor(35WV 10µF) [C951]
35 VCKYTV1CB105K AC C Capacitor(16WV 1µF) [C1053]
36 VCKYTV1AB225M AC C Capacitor(10WV 2.2µF) [C1054]
37 VCCCCZ1HH330J AA C Capacitor(50WV 33pF) [C1056]
38 VHDRLS73///-1 AA B Diode(RLS73) [D8,D9,D23,D24,D41]
39 VHDDAP202U/-1 AB B Diode(DAP202U) [D10]
VHDRB451F//-1 AD B Diode(RB451F) [D12,D14,D26,D27,D28,D29]
40
VHDRB451F//-1 AD B Diode(RB451F) [D30,D31,D35]
41 VHPSLR322VC3F AC B LED(Red)(SLR322VC3F) [D13]
42 VHERD2R0SBA-1 AC B Zener diode(RD2.0SB) [D25,D36,D32,D42]
! 43 QFS-D132CQCZZ AG A Fuse(tube)(215 1.25) [F1]
44 QFSHB0028FCZZ AC C Fuse holder(TP00351-31) [F1]
! 45 QFS-L930AQCZZ AF A Chip Fuse(CCF1N2) [F4]
46 RH-IX0006FCZZ BB B SDRAM(256Mbit) [IC4,IC5,IC6,IC7,IC27]
47 VHILCX14MT+0C AD B Logic IC(74LCX14MTCX_NL) [IC8,IC43,IC64]
48 VHI2309SZ1H-1 AT B IC(CY2309SZC-1HT) [IC9,IC29]
49 VHILCX74MT+0C AD B Logic IC(74LCX74MTCX_NL) [IC10,IC748,IC749]
50 VHILCX32MT+0C AD B Logic IC(74LCX32MTCX_NL) [IC11,IC747]
51 VHILVX1284+0C AM B Logic IC(74LVX161284MEA(LF)) [IC15]
52 VHIDS90L17N-1 AL B LVDS IC(DS90LV017ATMX-NOPB) [IC18]
53 VHI7065C30R-1 BU B CPU(RM7065C-300R-D004) [IC20]
54 VHIM87J4811-1 BH B ICU ASIC(SC87J4811) [IC25]
55 VHILCX08MT+0C AD B Logic IC(74LCX08MTCX_NL) [IC26,IC46,IC746,IC754]
56 VHI65946P7A-1 BA B ASIC1(uPD65946GN-P07-LMU-A) [IC32]
57 VHI28L64P20-1 AS B EEPROM(CAT28LV64L-20) [IC36]
58 QSOCZ6428ACZZ AE C IC socket(28pin) [IC36]
VHID62503FG-1 AG B Driver IC(TD62503FG) [IC38,IC41,IC44,IC45]
59
VHID62503FG-1 AG B Driver IC(TD62503FG) [IC719]
60 VHILM393D++-1 AE B IC(LM393D) [IC39,IC759]
61 VHINJ6356LF-1 AH B IC(NJU6356EM(LF)) [IC40]
– 24-2 –
manuals4you.com
T MFP control PWB
Inter- PRICE NEW PART Effective
NO. PARTS CODE change RANK MARK RANK DESCRIPTION TR No. time
62 VHIHI207ECB0C AN B RS232Driver IC(HIN207ECB-T) [IC42]
63 VHIPT598DLF-1 AE B Reset IC(PST598DN(LF)) [IC47,IC48]
64 VHIHG73C95V-1 AY B ASIC2(HG73C095TEV) [IC53]
65 VHI237R33LF-1 AF B IC(NJM2370R33) [IC54]
66 VHI23WAT255-1 AU B 2Mbit SRAM(N02L163WC2AT2-55I) [IC55]
67 VHI87R1060E-1 BQ B IC(MB87R1060V94 E1) [IC700]
68 VHDF1071MT+0C AH B Diode(74F1071MTCX_NL) [IC701]
69 VHIMRUP01++-1 BF B IC(MRUP01 V2) [IC703]
70 RCNVD0003FCZZ AY B DC-DC Converter(MPD4S008S(LF)) [IC718]
71 VHIPM22G75+-1 BH B CODEC IC(PM-22/75(LF)) [IC723,IC721]
72 VHIPM2060G+-1 BK B RET IC(PM2060i(LF)) [IC725]
VHILCX244MT0C AE B Logic IC(74LCX244MTCX_NL) [IC726,IC729,IC732,IC742]
73
VHILCX244MT0C AE B Logic IC(74LCX244MTCX_NL) [IC743,IC744,IC745]
VHILCX245MT0C AE B Logic IC(74LCX245MTCX_NL) [IC727,IC728,IC730,IC731]
74 VHILCX245MT0C AE B Logic IC(74LCX245MTCX_NL) [IC734,IC736,IC738,IC739]
VHILCX245MT0C AE B Logic IC(74LCX245MTCX_NL) [IC740,IC741]
75 VHILCX373MT0C AE B Logic IC(74LCX373MTCX_NL) [IC733,IC735,IC737]
76 VHIPT598ILF-1 AE B Reset IC(PST598IN(LF)) [IC753]
77 VHILCX157MT0C AE B Logic IC(74LCX157MTCX_NL) [IC755]
78 VHI65345Y020C BC B IC(UPD65345GJ-Y02-UEN-A) [IC756]
80 QPIN-0003GCPZ AC C Pin(T3B-SQ(LF)) [JP6]
81 PCAPH0010GCZZ AD C Cap(JM-2W-96) [JP6]
82 QJUM-0002FCZZ AA C Taping jumper wire(JUMPER,VIDCLK) [JP19]
RFILN0048FCPZ AB C Filter(BLM15BB121SN1D(LF)) [L2,L3,L724,L749]
83
RFILN0048FCPZ AB C Filter(BLM15BB121SN1D(LF)) [L750,L755]
85 RCILF0115FCZZ AG C Choke Coil(DLW31SN900SQ2) [L700]
86 RFILN0304FCPZ AC C EMI Filter(DSS6NZ82A103Q55B(LF)) [L701,L703,L705,L753,L754]
87 RFILN0305FCPZ AC C Filter(BL02RN2R1P1A(LF)) [L702,L704,L706]
RFILN0051FCZZ AC C Filter(MMZ1608D121BTA00) [L714,L715,L716,L717,L718]
RFILN0051FCZZ AC C Filter(MMZ1608D121BTA00) [L719,L720,L721,L737,L738]
88
RFILN0051FCZZ AC C Filter(MMZ1608D121BTA00) [L739,L740,L741,L742,L743]
RFILN0051FCZZ AC C Filter(MMZ1608D121BTA00) [L744]
89 RFILN0055FCZZ AB C Filter(BLM21AG121SN1D) [L722]
RFILN0056FCZZ AA C Filter(BLM18AG151SN1D) [L725,L728,L729,L745,L746]
90
RFILN0056FCZZ AA C Filter(BLM18AG151SN1D) [L747]
91 VHVICPS1.2/-1 AF B IC protector(ICPS1.2) [Q1,Q28]
92 VSDTC114EUA-1 AC B Transistor(DTC114EUA) [Q3,Q11,Q13,Q21,Q24,Q25,Q26]
93 VSDTC114YUA-1 AB B Transistor(DTC114YUA) [Q4,Q12,Q15,Q27]
94 VSUPA502TA+-1 AD B Transistor(UPA502T(LF)) [Q5,Q6,Q7]
95 VS2SC2412K/-1 AB B Transistor(2SC2412K) [Q18,Q8]
96 VS2SB1198K/-1 AC B Transistor(2SB1198K) [Q17,Q9]
97 VSDTA114EUA-1 AC B Transistor(DTA114EUA) [Q10,Q14,Q20]
98 VSTPC6108F+-1 AE B Transistor(TPC6108) [Q16]
99 VSTPC6004F+-1 AE B Transistor(TPC6004 (TE85L,F)) [Q19]
100 VSDTA143ZUA-1 AB B Transistor(DTA143ZUA FT106) [Q22]
101 VS2SK3018++-1 AC B Transistor(2SK3018) [Q23]
VHV1608C2701C AC B Varistor(AVR-M1608C270KT2AB) [RV12,RV13,RV14,RV15,RV16]
VHV1608C2701C AC B Varistor(AVR-M1608C270KT2AB) [RV17,RV18,RV19,RV20,RV21]
102
VHV1608C2701C AC B Varistor(AVR-M1608C270KT2AB) [RV22,RV23,RV24,RV25,RV26]
VHV1608C2701C AC B Varistor(AVR-M1608C270KT2AB) [RV27]
VRS-CZ1JD103J AA C Resistor(1/16W 10KΩ ±5%) [R12,R13,R15,R16,R18,R44]
VRS-CZ1JD103J AA C Resistor(1/16W 10KΩ ±5%) [R45,R60,R61,R62,R70,R72]
VRS-CZ1JD103J AA C Resistor(1/16W 10KΩ ±5%) [R86,R91,R93,R123,R131]
VRS-CZ1JD103J AA C Resistor(1/16W 10KΩ ±5%) [R158,R159,R160,R163,R165]
VRS-CZ1JD103J AA C Resistor(1/16W 10KΩ ±5%) [R167,R168,R203,R208,R213]
VRS-CZ1JD103J AA C Resistor(1/16W 10KΩ ±5%) [R216,R217,R230,R237,R238]
VRS-CZ1JD103J AA C Resistor(1/16W 10KΩ ±5%) [R239,R240,R241,R242,R245]
VRS-CZ1JD103J AA C Resistor(1/16W 10KΩ ±5%) [R246,R249,R254,R259,R260]
VRS-CZ1JD103J AA C Resistor(1/16W 10KΩ ±5%) [R261,R263,R264,R267,R269]
VRS-CZ1JD103J AA C Resistor(1/16W 10KΩ ±5%) [R271,R272,R273,R274,R282]
VRS-CZ1JD103J AA C Resistor(1/16W 10KΩ ±5%) [R283,R284,R285,R429,R430]
103
VRS-CZ1JD103J AA C Resistor(1/16W 10KΩ ±5%) [R480,R494,R795,R796,R805]
VRS-CZ1JD103J AA C Resistor(1/16W 10KΩ ±5%) [R824,R833,R839]
VRS-CZ1JD103J AA C Resistor(1/16W 10KΩ ±5%) [R845,R859,R947,R949,R974]
VRS-CZ1JD103J AA C Resistor(1/16W 10KΩ ±5%) [,R976,R977,R978,R981]
VRS-CZ1JD103J AA C Resistor(1/16W 10KΩ ±5%) [R1016,R1070,R1120,R1121]
VRS-CZ1JD103J AA C Resistor(1/16W 10KΩ ±5%) [R1122,R1130,R1131]
VRS-CZ1JD103J AA C Resistor(1/16W 10KΩ ±5%) [R1132,R1133,R1134,R1135]
VRS-CZ1JD103J AA C Resistor(1/16W 10KΩ ±5%) [R1167,R1168,R1174,R1204]
VRS-CZ1JD103J AA C Resistor(1/16W 10KΩ ±5%) [R1226,R1246,R1248,R1249]
VRS-CZ1JD103J AA C Resistor(1/16W 10KΩ ±5%) [R1250,R1260,R1283,R1286]
VRS-CZ1JD103J AA C Resistor(1/16W 10KΩ ±5%) [R1294,R1296]
VRS-CZ1JD220J AA C Resistor(1/16W 22Ω ±5%) [R14,R17,R19,R24,R27,R30]
VRS-CZ1JD220J AA C Resistor(1/16W 22Ω ±5%) [R31,R34,R35,R37,R39,R40]
104 VRS-CZ1JD220J AA C Resistor(1/16W 22Ω ±5%) [R43,R46,R51,R54,R57,R814]
VRS-CZ1JD220J AA C Resistor(1/16W 22Ω ±5%) [R815,R816,R817,R1022]
VRS-CZ1JD220J AA C Resistor(1/16W 22Ω ±5%) [R1273]
– 24-3 –
T MFP control PWB
Inter- PRICE NEW PART Effective
NO. PARTS CODE change RANK MARK RANK DESCRIPTION TR No. time
VRS-CZ1JD330J AA C Resistor(1/16W 33Ω ±5%) [R41,R47,R48,R52,R64,R65]
VRS-CZ1JD330J AA C Resistor(1/16W 33Ω ±5%) [R67,R69,R92,R96,R117]
VRS-CZ1JD330J AA C Resistor(1/16W 33Ω ±5%) [R138,R142,R143,R147,R148]
VRS-CZ1JD330J AA C Resistor(1/16W 33Ω ±5%) [R152,R153,R173,R174,R176]
VRS-CZ1JD330J AA C Resistor(1/16W 33Ω ±5%) [R187,R214,R288,R289,R524]
VRS-CZ1JD330J AA C Resistor(1/16W 33Ω ±5%) [R525,R526,R527,R528,R529]
VRS-CZ1JD330J AA C Resistor(1/16W 33Ω ±5%) [R530,R531,R532,R533,R534]
105
VRS-CZ1JD330J AA C Resistor(1/16W 33Ω ±5%) [R535,R536,R537,R538,R539]
VRS-CZ1JD330J AA C Resistor(1/16W 33Ω ±5%) [R540,R542,R543,R545,R547]
VRS-CZ1JD330J AA C Resistor(1/16W 33Ω ±5%) [R548,R549,R550,R551,R624]
VRS-CZ1JD330J AA C Resistor(1/16W 33Ω ±5%) [R701,R703,R705,R707,R710]
VRS-CZ1JD330J AA C Resistor(1/16W 33Ω ±5%) [R711,R712,R713,R753,R783]
VRS-CZ1JD330J AA C Resistor(1/16W 33Ω ±5%) [R791,R799,R1067,R1068]
VRS-CZ1JD330J AA C Resistor(1/16W 33Ω ±5%) [R1173,R1185,R1270]
VRS-CZ1JD470J AA C Resistor(1/16W 47Ω ±5%) [R55,R56,R58,R66,R188]
106 VRS-CZ1JD470J AA C Resistor(1/16W 47Ω ±5%) [R190,R787,R788,R1251]
VRS-CZ1JD470J AA C Resistor(1/16W 47Ω ±5%) [R1252]
VRS-CZ1JD100J AA C Resistor(1/16W 10Ω ±5%) [R59,R116,R118,R149,R161]
VRS-CZ1JD100J AA C Resistor(1/16W 10Ω ±5%) [R169,R170,R504,R718,R721]
VRS-CZ1JD100J AA C Resistor(1/16W 10Ω ±5%) [R722,R725,R726,R729,R749]
VRS-CZ1JD100J AA C Resistor(1/16W 10Ω ±5%) [R750,R751,R752,R755,R756]
107 VRS-CZ1JD100J AA C Resistor(1/16W 10Ω ±5%) [R757,R785,R790,R801,R809]
VRS-CZ1JD100J AA C Resistor(1/16W 10Ω ±5%) [R1066,R1069,R1092,R1093]
VRS-CZ1JD100J AA C Resistor(1/16W 10Ω ±5%) [R1094,R1095,R1096,R1097]
VRS-CZ1JD100J AA C Resistor(1/16W 10Ω ±5%) [R1098,R1099,R1100,R1101]
VRS-CZ1JD100J AA C Resistor(1/16W 10Ω ±5%) [R1102,R1103,R1104,R1105]
VRS-CZ1JD472J AA C Resistor(1/16W 4.7KΩ ±5%) [R71,R121,R128,R162,R164]
VRS-CZ1JD472J AA C Resistor(1/16W 4.7KΩ ±5%) [R184,R206,R221,R227,R228]
VRS-CZ1JD472J AA C Resistor(1/16W 4.7KΩ ±5%) [R231,R262,R270,R277,R434]
VRS-CZ1JD472J AA C Resistor(1/16W 4.7KΩ ±5%) [R435,R478,R492,R714,R715]
VRS-CZ1JD472J AA C Resistor(1/16W 4.7KΩ ±5%) [R716,R717,R731,R733,R734]
VRS-CZ1JD472J AA C Resistor(1/16W 4.7KΩ ±5%) [R763,R767,R769,R811,R822]
108 VRS-CZ1JD472J AA C Resistor(1/16W 4.7KΩ ±5%) [R863,R864,R929,R930,R936]
VRS-CZ1JD472J AA C Resistor(1/16W 4.7KΩ ±5%) [R937,R938,R939,R944,R945]
VRS-CZ1JD472J AA C Resistor(1/16W 4.7KΩ ±5%) [R1010,R1012,R1014,R1025]
VRS-CZ1JD472J AA C Resistor(1/16W 4.7KΩ ±5%) [R1028,R1032,R1056,R1088]
VRS-CZ1JD472J AA C Resistor(1/16W 4.7KΩ ±5%) [R1089,R1179,R1180,R1181]
VRS-CZ1JD472J AA C Resistor(1/16W 4.7KΩ ±5%) [R1182,R1202,R1208,R1210]
VRS-CZ1JD472J AA C Resistor(1/16W 4.7KΩ ±5%) [R1216,R1282,R1287,R1291]
VRS-CZ1JD101J AA C Resistor(1/16W 100Ω ±5%) [R101,R102,R109,R180,R181]
109
VRS-CZ1JD101J AA C Resistor(1/16W 100Ω ±5%) [R183,R403,R404,R1176,R1284]
110 VRS-CZ1JD333J AA C Resistor(1/16W 33KΩ ±5%) [R179,R107]
111 VRS-CZ1JD332J AA C Resistor(1/16W 3.3KΩ ±5%) [R215,R119]
VRS-CZ1JD102J AA C Resistor(1/16W 1.0KΩ ±5%) [R129,R130,R134,R151,R204]
VRS-CZ1JD102J AA C Resistor(1/16W 1.0KΩ ±5%) [R205,R236,R253,R268,R279]
112 VRS-CZ1JD102J AA C Resistor(1/16W 1.0KΩ ±5%) [R419,R1203,R1223,R1227]
VRS-CZ1JD102J AA C Resistor(1/16W 1.0KΩ ±5%) [R1228,R1230,R1245,R1247]
VRS-CZ1JD102J AA C Resistor(1/16W 1.0KΩ ±5%) [R1255,R1269]
VRS-CZ1JD000J AA C Resistor(1/16W 0Ω ±5%) [R133,R141,R166,R198,R220]
VRS-CZ1JD000J AA C Resistor(1/16W 0Ω ±5%) [R232,R290,R291,R292,R293]
VRS-CZ1JD000J AA C Resistor(1/16W 0Ω ±5%) [R296,R297,R298,R299,R300]
VRS-CZ1JD000J AA C Resistor(1/16W 0Ω ±5%) [R301,R302,R303,R304,R305]
VRS-CZ1JD000J AA C Resistor(1/16W 0Ω ±5%) [R306,R307,R406,R437,R438]
VRS-CZ1JD000J AA C Resistor(1/16W 0Ω ±5%) [R439,R440,R441,R442,R443]
VRS-CZ1JD000J AA C Resistor(1/16W 0Ω ±5%) [R444,R484,R485,R736,R737]
VRS-CZ1JD000J AA C Resistor(1/16W 0Ω ±5%) [R745,R754,R760,R762,R766]
VRS-CZ1JD000J AA C Resistor(1/16W 0Ω ±5%) [R772,R774,R775,R776,R802]
VRS-CZ1JD000J AA C Resistor(1/16W 0Ω ±5%) [R807,R810,R819,R820,R821]
VRS-CZ1JD000J AA C Resistor(1/16W 0Ω ±5%) [R826,R827,R828,R829,R836]
VRS-CZ1JD000J AA C Resistor(1/16W 0Ω ±5%) [R838,R842,R844,R848]
113 VRS-CZ1JD000J AA C Resistor(1/16W 0Ω ±5%) [R854,R858,R862,R940,R941]
VRS-CZ1JD000J AA C Resistor(1/16W 0Ω ±5%) [R942,R943,R985,R989,R991]
VRS-CZ1JD000J AA C Resistor(1/16W 0Ω ±5%) [R850,R852,R993,R995,R997]
VRS-CZ1JD000J AA C Resistor(1/16W 0Ω ±5%) [R999,R1001,R1003,R1005]
VRS-CZ1JD000J AA C Resistor(1/16W 0Ω ±5%) [R1007,R1019,R1020,R1023]
VRS-CZ1JD000J AA C Resistor(1/16W 0Ω ±5%) [R1029,R1031,R1071,R1072]
VRS-CZ1JD000J AA C Resistor(1/16W 0Ω ±5%) [R1146]
VRS-CZ1JD000J AA C Resistor(1/16W 0Ω ±5%) [R1184,R1211,R1212,R1213]
VRS-CZ1JD000J AA C Resistor(1/16W 0Ω ±5%) [R1217,R1219,R1221,R1224]
VRS-CZ1JD000J AA C Resistor(1/16W 0Ω ±5%) [R1231,R1235,R1253]
VRS-CZ1JD000J AA C Resistor(1/16W 0Ω ±5%) [R1259,R1263,R1266,R1267]
VRS-CZ1JD000J AA C Resistor(1/16W 0Ω ±5%) [R1268,R1278,R1279,R1290]
VRS-CZ1JD000J AA C Resistor(1/16W 0Ω ±5%) [R1295]
VRS-CZ1JD222J AA C Resistor(1/16W 2.2KΩ ±5%) [R199,R200,R209,R210,R211]
VRS-CZ1JD222J AA C Resistor(1/16W 2.2KΩ ±5%) [R223,R244,R248,R265,R266]
114
VRS-CZ1JD222J AA C Resistor(1/16W 2.2KΩ ±5%) [R276,R471,R980,R1124]
VRS-CZ1JD222J AA C Resistor(1/16W 2.2KΩ ±5%) [R1225]
115 VRS-CZ1JD823J AA C Resistor(1/16W 82KΩ ±5%) [R202]
116 VRS-CZ1JD183J AA C Resistor(1/16W 18KΩ ±5%) [R280,R275]
– 24-4 –
manuals4you.com
T MFP control PWB
Inter- PRICE NEW PART Effective
NO. PARTS CODE change RANK MARK RANK DESCRIPTION TR No. time
117 VRS-CZ1JD511J AA C Resistor(1/16W 510Ω ±5%) [R278]
118 VRS-CZ1JD361F AA C Resistor(1/16W 360Ω ±1%) [R417]
119 VRS-CZ1JD561F AA C Resistor(1/16W 560Ω ±1%) [R418]
120 VRS-CZ1JD820J AA C Resistor(1/16W 82Ω ±5%) [R541,R544,R546]
121 VRS-CZ1JD221J AA C Resistor(1/16W 220Ω ±5%) [R797]
122 VRS-CZ1JD105J AA C Resistor(1/16W 1.0MΩ ±5%) [R798]
123 VRS-CZ1JD622J AA C Resistor(1/16W 6.2KΩ ±5%) [R804]
124 VRS-CZ1JD562F AA C Resistor(1/16W 5.6KΩ ±1%) [R950]
125 VRS-CZ1JD472F AA C Resistor(1/16W 4.7KΩ ±1%) [R951]
126 VRS-CZ1JD563J AA C Resistor(1/16W 56KΩ ±5%) [R1090,R1091]
127 VRS-CZ1JD562J AA C Resistor(1/16W 5.6KΩ ±5%) [R1261,R1229]
VRS-TX2HD000J AB C Resistor(1/2W 0Ω ±5%) [R1242,R1243,R1359,R1360]
128
VRS-TX2HD000J AB C Resistor(1/2W 0Ω ±5%) [R1361]
129 VRS-CZ1JD471J AA C Resistor(1/16W 470Ω ±5%) [R1272]
130 VRS-CZ1JD474J AA C Resistor(1/16W 470KΩ ±5%) [R1281]
131 VRS-CZ1JD152F AA C Resistor(1/16W 1.5KΩ ±1%) [R1285]
VRS-CY1JD000J AA C Resistor(1/16W 0Ω ±5%) [R1364,R1365,R1366,R1367]
VRS-CY1JD000J AA C Resistor(1/16W 0Ω ±5%) [R1368,R1369,R1370,R1371]
132
VRS-CY1JD000J AA C Resistor(1/16W 0Ω ±5%) [R1372,R1373,R1374,R1375]
VRS-CY1JD000J AA C Resistor(1/16W 0Ω ±5%) [R1376,R1377,R1378,R1379]
133 QSW-S0545FCPZ AM B DIP switch(OTAX KSP02(LF)) [SW2]
134 RCRUA0024FCPZ AL B Crystal(SG-8002JC 66.0MHz(LF)) [X1]
135 RCRUA0008FCPZ AL B Crystal(SG-8002JC 40.57MHz(LF)) [X2]
136 RCRUA0002QSPZ AL B Crystal(SG-8002JC 33.33333MHz(LF)) [X3]
137 RCRUA0007FCPZ AL B Crystal(SG-8002JC 31.554MHz(LF)) [X4]
138 RCRUA0023FCPZ AL B Crystal(SG-8002JC 64.0M) [X5]
139 RCRSA0085FCPZ AE B Crystal(DT-38 32.768K(LF)) [X6]
140 RCRUA0005FCPZ AL B Crystal(SG-8002JC 14.7456M(LF)) [X7]
141 RCRUA0027FCPZ AL B Crystal(SG-8002JC 74.9M(LF)) [X700]
142 RCRSC0082FCPZ AH B Crystal(MA-406 24MHz(LF)) [X701]
143 RCRUA0009FCPZ AL B Crystal(SG-8002JC 66.666MHz(LF)) [X703]
– 24-5 –
U Fuse PWB
Inter- PRICE NEW PART Effective
NO. PARTS CODE change RANK MARK RANK DESCRIPTION TR No. time
1 QCNCM0895FCZZ AG C Connector(3pin) [CN1]
! QFS-B3631QCPZ AH A Fuse(15A 250V) (100V Series)[F1]
2
! QFS-D1421QCPZ AE A Fuse(10A 240V) (200V Series)[F1,2]
3 QFSHB0028FCZZ AC C Fuse holder(00335-31) [F1,2]
4 QTANP0215FCZZ AC C Terminal(85163) [Lout,LFAX,Nout,NFAX]
5 QTANP0218FCPZ AC C Terminal(TP00370-21) [FG]
6 QSPGC0001FCZZ AK B Surge absorber(2700V) (100V Series)[A1]
7 VHV10V471K+-1 AD B Varistor(10V471K) [VR1]
8 DHAI-3252FCZ1 AE C DH harness
(Unit)
CPWBF1626FCE1 AU E Fuse PWB (100V Series)
901
CPWBF1627FCE2 AW E Fuse PWB (200V Series)
– 25-1 –
manuals4you.com
Update : 06/02/27
V Relay PWB
Inter- PRICE NEW PART Effective
NO. PARTS CODE change RANK MARK RANK DESCRIPTION TR No. time
1 RRLYD2112QCZZ AL B Relay(ALE15B12) [RY1,RY2]
VHDDSM1D1//-1 AB B Diode(DSM1D1) [D1]
2
VHD10JDA10+-1 1 AB B Diode(10JDA10) [D1] 06/05
3 VS2SD1768S+-1 AR B Transistor(2SD1768) [Q1]
4 VRD-HT2EY471J AA C Resistor(1/4W 470Ω ±5%) [R1]
5 VRD-HT2EY272J AA C Resistor(1/4W 2.7KΩ ±5%) [R2]
6 VCEAZA1VW476M AC C Capacitor(35WV 47µF) [C1]
7 QCNCM0672FCZZ AB C Connector(2pin) [CN1]
8 QCNCM1178FCZZ AC C Connector(2pin) [CN2]
9 QCNCM7014SC0C AA C Connector(3pin) [CN3]
10 QTANP0215FCZZ AC C Terminal(85163) [Lin,Nin,Lout,Nout]
! 11 QFS-E1312QCZZ AD A Fuse(T2.5AH250V) [F1]
12 QFSHB0028FCZZ AC C Fuse holder(TP00351-31) [(F1)]
VHV10V271K+-1 AD B Varistor(10V271K) (100V Series)[VR1]
13
VHV10V471K+-1 AD B Varistor(10V471K) (200V Series)[VR1]
(Unit)
CPWBF1629FCE1 AY E Relay PWB (100V Series)
901
CPWBF1629FCE2 AY E Relay PWB (200V Series)
– 26-1 –
W Power supply PWB 100V[Except AR-M312U,AR-M420U]
Inter- PRICE NEW PART Effective
NO. PARTS CODE change RANK MARK RANK DESCRIPTION TR No. time
1 0AV1570000002 AD C FILM CAPACITOR(LE104-L 0.1µF,250V(LE)) [C701]
2 0AV1570000003 AD C FILM CAPACITOR(LE104-C 0.1µF,250V(LE)) [C760,C761]
3 0AV1570000004 AN C FILM CAPACITOR(LE155-C 1.5µF,250V(LE)) [C702]
4 0AV1650000064 AD C CERAMIC CAPACITOR(DE1307E472M-KH 4700pF(KH)) [C703,C704]
5 0AV1570000006 AF C FILM CAPACITOR(LE474-C 0.47µF,250V(LE)) [C705]
AL-ELECTROLYTIC CAPACITOR (LGU2D182MELC 1800mF 200V)
6 0AV1390000260 AY C
[C706]
CERAMIC CAPACITOR(PRE132R104K50 0.1µF,50V)
0AV1690000133 AC C
[C707,C718,C720,C730,C733,C742]
7
CERAMIC CAPACITOR(PRE132R104K50 0.1µF,50V)
0AV1690000133 AC C
[C752,C756,C759,C765]
CERAMIC CAPACITOR(DE0905-979R102K1K 1000pF,1KV)
8 0AV1610000091 AC C
[C708,C709,C710,C726,C747,C748,C749]
9 0AV1390000261 AC C AL-ELECTROLYTIC CAPACITOR(UPJ1H4R7MDD 4.7µF,50V) [C711]
AL-ELECTROLYTIC CAPACITOR(UPJ1H220MED 22µF,50V)
10 0AV1390000262 AC C
[C712,C766,C768]
11 0AV1690000113 AE C CERAMIC CAPACITOR(DE1610-2E472M-KX 4700pF(KX)) [C713,C767]
12 0AV1480000084 AD C FILM CAPACITOR(CQMY-92MC2A104J 0.1µF,100V) [C714,C715]
CERAMIC CAPACITOR(RPE132R103K50 0.01µF,50V)
13 0AV1690000134 AC C
[C716,C717,C763]
14 0AV1690000138 AC C CERAMIC CAPACITOR(RPE132R472K50 4700pF,50V) [C719,C757]
15 0AV1610000109 AC C CERAMIC CAPACITOR(DE0705-979R471K1K 470pF,1KV) [C721,C722]
AL-ELECTROLYTIC CAPACITOR(UPJ1V182MHD6 1800µF,35V)
16 0AV1390000263 AC C
[C728,C729]
17 0AV1390000264 AC C AL-ELECTROLYTIC CAPACITOR(UPJ1H010MDD 1µF,50V) [C734,C771]
18 0AV1390000265 AC C AL-ELECTROLYTIC CAPACITOR(UHD1V681MHD 680µF,35V) [C735]
19 0AV1390000266 AG C AL-ELECTROLYTIC CAPACITOR(UHD1V102MHD 1000µF,35V) [C738]
CERAMIC CAPACITOR(RPE132R223K50 0.022µF,50V)
20 0AV1390000136 AF C
[C739,C744,C746,C755]
AL-ELECTROLYTIC CAPACITOR(UPJ1H2R2MDD 2.2µF,50V)
21 0AV1390000267 AC C
[C740,C753]
22 0AV1390000268 AC C AL-ELECTROLYTIC CAPACITOR(UHD1C222MHD 2200µF,16V) [C741]
CERAMIC CAPACITOR(RPE132R102K50 1000pF,50V)
23 0AV1690000137 AC C
[C743,C745,C770]
AL-ELECTROLYTIC CAPACITOR(UHD1A562MHD 5600µF,10V)
24 0AV1390000269 AK C
[C750,C751]
25 0AV1390000270 AD C AL-ELECTROLYTIC CAPACITOR(UPJ1V820MED 82µF,35V) [C754]
26 0AV1480000107 AE C FILM CAPACITOR(ECQE2104RJF 0.1µF,400V) [C764]
27 0AV1390000271 AC C AL-ELECTROLYTIC CAPACITOR(UPJ1C101MED 100µF,16V) [C772]
28 0AV3060035000 AE B DIODE(S1WB(A)60 1A,600V) [D701]
29 0AV3070123000 AC B ZENER DIODE(RD6.8ES 400mW) [D702]
30 0AV3060031000 AC B DIODE(ERA15-04 1A,400V) [D703,D704,D748,D763]
31 0AV3060040000 AR B DIODE(D15XB60 15A,600V) [D705]
0AV3050019000 AF B DIODE(ERA91-02 0.5A,200V) [D706,D708,D710,D717,D746]
32
0AV3050019000 AF B DIODE(ERA91-02 0.5A,200V) [D747,D755,D758,D759]
0AV3050091000 AB B DIODE(1SS270 60V,150mA) [D707,D714,D726,D727,D728]
33 0AV3050091000 AB B DIODE(1SS270 60V,150mA) [D731,D733,D738,D743,D744]
0AV3050091000 AB B DIODE(1SS270 60V,150mA) [D751,D752,D754,D760,D762]
34 0AV3070085000 AC B ZENER DIODE(RD33ES 400mW) [D709,D712,D756]
35 0AV3070056000 AD B ZENER DIODE(RD20ES 400mW) [D716]
36 0AV3070013000 AB B ZENER DIODE(RD5.6ES 400mW) [D715,D720,D734,D736,D739]
37 0AV3050087000 AN B DIODE(YG906C2R 20A,200V) [D721]
38 0AV3070061000 AC B ZENER DIODE(RD4.7ES 400mW) [D724]
39 0AV3050070000 AK B DIODE(YG802C06 10A,60V) [D729]
40 0AV3050080000 AP B DIODE(YG805C04 20A,40V) [D730]
41 0AV3070081000 AC B ZENER DIODE(RD3.9ES 400mW) [D732]
42 0AV3070069000 AC B ZENER DIODE(RD51E 500mW) [D735]
43 0AV3070014800 AC B ZENER DIODE(RD10ES 400mW) [D742,D749]
44 0AV3070112000 AC B ZENER DIODE(RD3.0ES 400mW) [D745,D753]
45 0AV3070023000 AE B ZENER DIODE(RD24ES 400mW) [D713,D757]
46 0AV3070049000 AB B ZENER DIODE(RD27ES 400mW) [D761]
47 0AV3070156000 AC B ZENER DIODE(RD4.3ES 400mW) [D765]
48 0AV3050104000 AD B DIODE(AK04) [D750,D764]
49 0AV3090079000 AL B IC(FA5515P) [IC701,IC705]
50 0AV3090041000 AF B IC(UPC1093J-1) [IC702,IC704]
51 0AV3090008000 AK B IC(MB3759P) [IC703]
52 0AV4070063000 AR C INDUCTOR(DRC31-15A202) [L701]
53 0AV4070064000 AL C INDUCTOR(DRB25-05A202) [L702]
54 0AV4120013000 AC C INDUCTOR(T314OP3206536HW) [L703,L710,L715]
55 0AV4050016000 AG C INDUCTOR(PC8T8R2M) [L707]
56 0AV4120008000 AD C INDUCTOR(LFP3A) [L708]
57 0AV4080011400 AL C INDUCTOR(HK-10S100-4500S) [L709]
58 0AV4120002000 AC C INDUCTOR(B-01-A) [L711,L713,L714]
59 0AV4050010000 AH C INDUCTOR(PC8T3R3M) [L712]
60 0AV3080421300 AE B PHOTO COUPLER(PS2561A) [PC701,PC703,PC704,PC706]
61 0AV3180000009 AL B PHOTO TRIAC COUPLER(PC3SF11YV) [PC702,PC705]
62 0AV3042698000 AS B FET(2SK2698 500V,15A) [Q701]
63 0AV3001015500 AC B TRANSISTOR(2SA1015 -50V,-150mA) [Q702,Q713]
64 0AV3042543000 AQ B FET(2SK2543 500V,8A) [Q704]
0AV3021815500 AC B TRANSISTOR(2SC1815 50V 150mA) [Q706,Q709,Q710,Q711,Q714]
65
0AV3021815500 AC B TRANSISTOR(2SC1815 50V 150mA) [Q715,Q717,Q718,Q719,Q723]
– 27-1 –
manuals4you.com
W Power supply PWB 100V[Except AR-M312U,AR-M420U]
Inter- PRICE NEW PART Effective
NO. PARTS CODE change RANK MARK RANK DESCRIPTION TR No. time
66 0AV3040504000 AN B FET(2SJ504) [Q707]
67 0AV3022655500 AE B TRANSISTOR(2SC2655) [Q708]
68 0AV3042736000 AN B FET(2SK2736) [Q712]
69 0AV3021002999 AD B TRANSISTOR(RN1002) [Q720,Q721,Q722]
70 0AV2022213040 AC C METAL OXIDE FILM RESISTOR(RSU01WST5A221J 220Ω 1W) [R701]
71 0AV2054754077 AF C CEMENT FILLED RESISTOR(MNS05WNZ4R7J 4.7Ω 5W) [R702]
FLAME PROOF CARBON RESISTOR(RDF50S4.7KΩJ 4.7KΩ 1/2W)
72 0AV2014723030 AB C
[R703,R704,R705]
FLAME PROOF CARBON RESISTOR(RDF16S22KΩJ 22KΩ,1/6W)
73 0AV2012233010 AA C
[R706,R772,R827,R828]
FLAME PROOF CARBON RESISTOR(RDF50S180KΩJ 180W 1/2W)
74 0AV2011843030 AB C
[R707]
75 0AV2990106000 AC C METAL OXIDE FILM RESISTOR(RSMF1B273F 27KΩ 1W) [R708,R709]
76 0AV2011053010 AB C FLAME PROOF CARBON RESISTOR(RDF16S1MΩJ 1MΩ 1/6W) [R710]
FLAME PROOF CARBON RESISTOR(RDF16S1KΩJ 1KΩ,1/6W)
77 0AV2011023010 AA C
[R711,R737,R750,R784,R817,R751]
78 0AV2051083055 AE C CEMENT FILLED RESISTOR(BPR02WFTR10J 0.1Ω 2W) [R739]
FLAME PROOF CARBON RESISTOR(RDF25S47KΩJ 47KΩ 1/4W)
79 0AV2014733020 AB C
[R713,R714]
FLAME PROOF CARBON RESISTOR(RDF50S120ΩJ 120Ω 1/2W)
80 0AV2011213030 AB C
[R715,R732,R726,R728]
81 0AV2011203020 AB C FLAME PROOF CARBON RESISTOR(RDF25S12ΩJ 12Ω1/4W) [R716]
FLAME PROOF CARBON RESISTOR(RDF16S10KΩJ 10KΩ,1/6W)
0AV2011033010 AA C
[R717,R730,R735,R741,R753,R758]
82
FLAME PROOF CARBON RESISTOR(RDF16S10KΩJ 10KΩ,1/6W)
0AV2011033010 AA C
[R776,R795,R800,R818,R824,R825]
METAL OXIDE FILM RESISTOR(RSS5FB100ΩJH1 100Ω 5W)
83 0AV2021013078 AF C
[R718,R744]
FLAME PROOF CARBON RESISTOR(RDF16S3.3KΩJ 3.3KW 1/6W)
84 0AV2013323010 AA C
[R719,R775]
85 0AV2021213040 AC C METAL OXIDE FILM RESISTOR(RSF1B120ΩJ 120Ω 1W) [R720,R731]
86 0AV2990142000 AA C METAL FILM RESISTOR(SN16S909ΩD 909Ω 1/6W) [R721]
FLAME PROOF CARBON RESISTOR(RDF16S39KΩJ 39KΩ,1/6W)
87 0AV2013933010 AA C
[R790]
88 0AV2148203040 AC C METAL OXIDE FILM RESISTOR(RSS182ΩJ 82Ω 1W) [R723]
FLAME PROOF CARBON RESISTOR(RDF16S220KΩJ 220KW,1/6W)
89 0AV2012243010 AA C
[R724]
90 0AV2041013020 AC B FUSING RESISTOR(RF25S100ΩJ 100Ω 1/4W) [R725,R727]
91 0AV2051083055 AE C CEMENT FILLED RESISTOR(BPR02WFTR10J 0.1Ω 2W) [R712]
FLAME PROOF CARBON RESISTOR(RDF16S2.2KΩJ 2.2KΩ,1/6W)
0AV2012223010 AA C
[R749,R766,R777,R807,R808]
92
FLAME PROOF CARBON RESISTOR(RDF16S2.2KWJ 2.2KΩ,1/6W)
0AV2012223010 AA C
[R815,R810,R797]
93 0AV2011813010 AA C FLAME PROOF CARBON RESISTOR(RDF16S180ΩJ 180Ω,1/6W)[R768]
94 0AV2990105000 AB C METAL FILM RESISTOR(SN16S68KΩD 68KΩ,1/6W) [R736]
95 0AV2041213010 AC B FUSING RESISTOR(RF16S120ΩJ 120Ω 1/6W) [R738]
96 0AV2012203020 AA C FLAME PROOF CARBON RESISTOR(RDF25S22ΩJ 22Ω 1/4W) [R740]
FLAME PROOF CARBON RESISTOR(RDF16S82KΩJ 82KΩ,1/6W)
97 0AV2018233010 AA C
[R742]
98 0AV2024703078 AF C METAL OXIDE FILM RESISTOR(RSS5FB47ΩJH1 47Ω 5W) [R743]
FLAME PROOF CARBON RESISTOR(RDF25S33KΩJ 33KΩ 1/4W)
99 0AV2013333020 AA C
[R746,R747]
FLAME PROOF CARBON RESISTOR(RDF16S33KΩJ 33KΩ 1/6W)
100 0AV2013333010 AA C
[R748]
101 0AV2990141000 AA C METAL FILM RESISTOR(SN16S180ΩD 180Ω 1/6W) [R734]
102 0AV2990083000 AC C METAL FILM RESISTOR(SN16S22.3KΩD 22.3KΩ 1/6W) [R754]
103 0AV2990010000 AC C METAL FILM RESISTOR(SN16S2.55KΩD 2.55KΩ 1/6W) [R755]
104 0AV2011533010 AA C FLAME PROOF CARBON RESISTOR(RDF16S15KΩJ 15KΩ 1/6W)[R756]
105 0AV2012213020 AA C FLAME PROOF CARBON RESISTOR(RDF25S220ΩJ 220Ω 1/4W)[R761]
106 0AV2014773020 AA C FLAME PROOF CARBON RESISTOR(RDF25S4.7ΩJ 4.7Ω 1/4W) [R762]
FLAME PROOF CARBON RESISTOR(RDF25S4.7KΩJ 4.7KW 1/4W)
107 0AV2014723020 AA C
[R763]
108 0AV2051094075 AG C CEMENT FILLED RESISTOR(BPR05WFTR10J 0.01Ω 5W) [R764]
FLAME PROOF CARBON RESISTOR(RDF16S5.6KΩJ 5.6KW 1/6W)
109 0AV2015623010 AA C
[R765]
110 0AV2041013010 AC B FUSING RESISTOR(RF16S100ΩJ 100Ω 1/6W) [R767]
FLAME PROOF CARBON RESISTOR(RDF25S120ΩJ 120Ω 1/4W)
111 0AV2011213020 AA C
[R769,R771]
FLAME PROOF CARBON RESISTOR(RDF16S12KΩJ 12KΩ 1/6W)
112 0AV2011233010 AA C
[R773]
113 0AV2990084000 AC C METAL FILM RESISTOR(SN16S1.2KΩD 1.2KΩ 1/6W) [R778]
114 0AV2990085000 AC C METAL FILM RESISTOR(SN16S39KΩD 39KΩ 1/6W) [R779]
115 0AV2142203040 AC C METAL OXIDE FILM RESISTOR(RSF1B22ΩJ 22Ω 1W) [R780]
116 0AV2013313010 AA C FLAME PROOF CARBON RESISTOR(RDF16S330ΩJ 330Ω 1/6W)[R781]
117 0AV2011013010 AA C FLAME PROOF CARBON RESISTOR(RDF16S100ΩJ 100Ω 1/6W)[R782]
118 0AV2013913010 AA C FLAME PROOF CARBON RESISTOR(RDF16S390ΩJ 390Ω 1/6W)[R783]
FLAME PROOF CARBON RESISTOR(RDF16S1.2KΩJ 1.2KΩ 1/6W)
119 0AV2011223010 AA C
[R785]
FLAME PROOF CARBON RESISTOR(RDF16S680ΩJ 680Ω 1/6W)
120 0AV2016813010 AA C
[R786]
FLAME PROOF CARBON RESISTOR(RDF16S120ΩJ 120Ω 1/6W)
121 0AV2011213010 AA C
[R791]
– 27-2 –
W Power supply PWB 100V[Except AR-M312U,AR-M420U]
Inter- PRICE NEW PART Effective
NO. PARTS CODE change RANK MARK RANK DESCRIPTION TR No. time
FLAME PROOF CARBON RESISTOR(RDF16S470ΩJ)
122 0AV2014713010 AA C
[R792,R814,R809,R826]
123 0AV2012733010 AA C FLAME PROOF CARBON RESISTOR(RDF16S27KΩJ) [R793,R794]
124 0AV2015633010 AA C FLAME PROOF CARBON RESISTOR(RDF16S56KΩJ) [R798]
125 0AV2043313010 AC B FUSING RESISTOR(RF16S330ΩJ) [R801]
126 0AV2021233040 AC C METAL OXIDE FILM RESISTOR(RSF1B12KΩJ) [R804,R805]
127 0AV2141803040 AC C METAL OXIDE FILM RESISTOR(RSMF1B18J) [R806]
128 0AV2011043020 AA C FLAME PROOF CARBON RESISTOR(RDF25S100KΩJ) [R811,R812]
129 0AV2014733010 AA C FLAME PROOF CARBON RESISTOR(RDF16S47KΩJ)[R813,R819,R820]
130 0AV2015633020 AA C FLAME PROOF CARBON RESISTOR(RDF25S56KΩJ) [R733]
131 0AV2042203010 AC B FUSING RESISTOR(RF16S22ΩJ) [R816]
FLAME PROOF CARBON RESISTOR(RDF16S4.7KΩJ)
132 0AV2014723010 AA C
[R821,R822,R752,R759,R774,R799]
133 0AV2011043010 AA C FLAME PROOF CARBON RESISTOR(RDF16S100KΩJ) [R823]
134 0AV2990104000 AC C METAL FILM RESISTOR(SN16S56KΩD) [R745]
135 0AV2041003020 AC B FUSING RESISTOR(RF25S10ΩJ) [R829]
136 0AV2990107000 AC C METAL FILM RESISTOR(SN16S1.5KΩD) [R729]
137 0AV2990112000 AC C METAL FILM RESISTOR(SN16S49.9KΩD) [R722]
138 0AV2060025000 AK B TEMP.FUSING RESISTOR(MEG05N4R7KB142) [FR701]
! 139 0AV4000136711 AY B Transformer(N-T01-367) [T701]
! 140 0AV4000131011 AQ B Transformer(N-T01-310) [T702]
141 0AV3160033000 AP B Traic(TM1641P) [TR701,TR703]
142 0AV3160037000 AN B Traic(BCR10PM-12LP) [TR702]
143 0AV2081029188 AC B POTENTIOMETER(RH063MC13R) [VR701,VR702]
144 0AV5080013000 AP B RELAY(OMIH-SS-124LM) [RL701]
145 0AV5190002000 AF B Varistor(ENC271D-10A-TA-B) [X701]
146 0AV5030126000 AG C Connector(B03P-VL) [CN1]
147 0AV5030127000 AD C Connector(B7B-PH-K-S) [CN2]
148 0AV5030128000 AD C Connector(B03B-XASK-1) [CN4]
149 0AV5030129000 AK C Connector(B12P-HL-A) [CN5]
150 0AV5030149000 AE C Connector(B5P-VH) [CN6]
151 0AV5030088000 AD C Connector(B2P-VH) [CN7]
152 0AV5130009000 AD C TERMINAL(TP82224-31)
153 0AV5130011000 AC C TERMINAL(TP00370-21)
154 0AV8117730416 AC C SCREW(NACPEW-B3X8SF)
155 0AV8117730516 AC C SCREW(NACPEW-B3X10SF)
156 0AV8117730616 AC C SCREW(NACPEW-B3X12SF)
157 0AV6113116511 AN C HEATSINK(LM31165)
158 0AV6114150911 AH C HEATSINK(LM41509)
159 0AV6114150111 AG C HEATSINK(LM41510)
160 0AV5050005000 AA C HOLDER(PFC5000-0203)
161 0AV7100003000 AE C INSULATION SHEET(M-30AD-D-3)
0AV5110012000 AB C Jumper wire(RJ-SKA-06) [RJ701,RJ702,RJ703,RJ708,RJ712]
0AV5110012000 AB C Jumper wire(RJ-SKA-06) [RJ713,RJ721,RJ727,RJ730,RJ735]
162
0AV5110012000 AB C Jumper wire(RJ-SKA-06) [RJ746,RJ760,RJ768,RJ769,RJ771]
0AV5110012000 AB C Jumper wire(RJ-SKA-06) [RJ772,RJ773,RJ775,RJ776]
0AV5110003000 AA C Jumper wire(RJ-SBA-06) [RJ707,RJ722,RJ723,RJ731,RJ736]
163
0AV5110003000 AA C Jumper wire(RJ-SBA-06) [RJ738,RJ739,RJ743,RJ748,RJ778]
0AV5110001000 AA C Jumper wire(RJ-SCA-06) [RJ711,RJ714,RJ716,RJ747,RJ756]
164
0AV5110001000 AA C Jumper wire(RJ-SCA-06) [RJ757,RJ759,RJ770,RJ779]
0AV5110006000 AA C Jumper wire(RJ-SDA-06) [RJ715,RJ718,RJ725,RJ726]
165 0AV5110006000 AA C Jumper wire(RJ-SDA-06) [RJ742,RJ745,RJ752,RJ754]
0AV5110006000 AA C Jumper wire(RJ-SDA-06) [RJ758,RJ763,RJ766,RJ774,RJ777]
166 0AV5110002000 AA C Jumper wire(RJ-SEA-06) [RJ704,RJ728,RJ733,RJ734,RJ753]
167 0AV5110011000 AB C Jumper wire(RJ-SFA-06) [RJ717,RJ729,RJ740,RJ741,RJ765]
0AV5110004000 AA C Jumper wire(RJ-SGA-06) [RJ705,RJ706,RJ709,RJ710,RJ719]
0AV5110004000 AA C Jumper wire(RJ-SGA-06) [RJ720,RJ724,RJ732,RJ737]
168
0AV5110004000 AA C Jumper wire(RJ-SGA-06) [RJ749,RJ750,RJ751,RJ755]
0AV5110004000 AA C Jumper wire(RJ-SGA-06) [RJ761,RJ762,RJ764,RJ767]
! 169 0AV5060176000 AD A FUSE(23706.3) [F701,F702,F704]
! 170 0AV5060177000 AE A FUSE(23704) [F703]
! 171 0AV5060018000 AG A FUSE(23710) [F706]
! 172 0AV5060089000 AE A FUSE(396 2) [F705]
(Unit)
! 901 RDENC0036FCZ3 BX E AC/DC power supply PWB 100
– 27-3 –
manuals4you.com
X Power supply PWB 100V[AR-M312U,AR-M420U]
Inter- PRICE NEW PART Effective
NO. PARTS CODE change RANK MARK RANK DESCRIPTION TR No. time
1 0AV1560000009 AE C Film capacitor(RE104-L 0.1µF 250V(RE)) [C701]
2 0AV1560000002 AD C Film capacitor(RE104-C 0.1µF 250V(RE)) [C760,C761]
3 0AV1560000008 AR C Film capacitor(RE155-C 1.5µF 250V(RE)) [C702]
4 0AV1690000074 AD C Ceramic capacitor(DE0807E102M-KH 1000PF(KH)) [C703,C704]
5 0AV1560000005 AH C Film capacitor(RE474-C 0.47µF 250V(RE)) [C705]
6 0AV1390000260 AY C AL-ELECTROLYTIC CAPACITOR(1800µF 200V) [C706]
0AV1690000133 AC C CERAMIC CAPACITOR(0.1µF 50V) [C707,C718,C720,C730,C733]
7
0AV1690000133 AC C CERAMIC CAPACITOR(0.1µF 50V) [C742,C752,C756,C759,C765]
Ceramic capacitor(DE0905-979R102K1K 1000PF 1KV)
0AV1610000091 AC C
8 [C708,C709,C710,C726,C747]
0AV1610000091 AC C Ceramic capacitor(DE0905-979R102K1K 1000PF 1KV) [C748,C749]
9 0AV1390000261 AC C AL-ELECTROLYTIC CAPACITOR(4.7µF 50V) [C711]
10 0AV1390000162 AD C AL-ELECTROLYTIC CAPACITOR(22µF 50V) [C712,C766,C768]
11 0AV1690000113 AE C Ceramic capacitor(DE1610-2E472M-KX 4700PF(KX)) [C713,C767]
12 0AV1480000109 AD C FILM CAPACITOR(0.1µF 50V) [C714,C715]
13 0AV1690000134 AC C CERAMIC CAPACITOR(0.01µF 50V) [C716,C717,C763]
14 0AV1690000138 AC C CERAMIC CAPACITOR(4700PF 50V) [C719,C757]
15 0AV1610000109 AC C Ceramic capacitor(DE0705-979R471K1K 470PF 1KV) [C721,C722]
16 0AV1390000263 AC C AL-ELECTROLYTIC CAPACITOR(1800µF 35V) [C728,C729]
17 0AV1390000264 AC C AL-ELECTROLYTIC CAPACITOR(1µF 50V) [C734,C771]
18 0AV1390000265 AC C AL-ELECTROLYTIC CAPACITOR(680µF 35V) [C735]
19 0AV1390000266 AG C AL-ELECTROLYTIC CAPACITOR(1000µF 35V) [C738]
20 0AV1690000136 AD C CERAMIC CAPACITOR(0.022µF 50V) [C739,C744,C746,C755]
21 0AV1390000267 AC C AL-ELECTROLYTIC CAPACITOR(2.2µF 50V) [C740,C753]
22 0AV1390000268 AC C AL-ELECTROLYTIC CAPACITOR(2200µF 16V) [C741]
23 0AV1690000137 AC C CERAMIC CAPACITOR(1000PF 50V) [C743,C745,C770]
24 0AV1390000269 AK C AL-ELECTROLYTIC CAPACITOR(5600µF 10V) [C750,C751]
25 0AV1390000270 AD C AL-ELECTROLYTIC CAPACITOR(82µF 35V) [C754]
26 0AV1480000107 AE C FILM CAPACITOR(0.1µF 400V) [C764]
27 0AV1390000271 AC C AL-ELECTROLYTIC CAPACITOR(100µF 16V) [C772]
28 0AV3060035000 AE B Diode(S1WB(A)60 1A 600V) [D701]
29 0AV3070123000 AC B Zenner diode(RD6.8ES 400mw) [D702]
30 0AV3060031000 AC B Diode(ERA15-04 1A 400V) [D703,D704,D748,D763]
31 0AV3060040000 AR B Diode(D15XB60 15A 600V) [D705]
0AV3050019000 AF B Diode(ERA91-02 0.5A 200V) [D706,D708,D710,D717,D746]
32
0AV3050019000 AF B Diode(ERA91-02 0.5A 200V) [D747,D755,D758,D759]
0AV3050086000 AB B Diode(1SS270A 0.15A 60V) [D707,D714,D726,D727,D728]
33 0AV3050086000 AB B Diode(1SS270A 0.15A 60V) [D731,D733,D737,D738,D743]
0AV3050086000 AB B Diode(1SS270A 0.15A 60V) [D744,D751,D752,D754,D760,D762]
34 0AV3070128000 AC B Zenner diode(RD33ES 400mW) [D709,D712,D756]
35 0AV3070115000 AC B Zenner diode(RD20ES 400mW) [D716]
36 0AV3070119000 AC B Zenner diode(RD5.6ES 400mW) [D715,D720,D734,D736,D739]
37 0AV3050087000 AN B Diode(YG906C2R 20A 200V) [D721]
38 0AV3070132000 AC B Zenner diode(RD4.7ES 400mW) [D724]
39 0AV3050070000 AK B Diode(YG802C06 10A 60V) [D729]
40 0AV3050080000 AP B Diode(YG805C04 20A 40V) [D730]
41 0AV3070124000 AC B Zenner diode(RD3.9ES 400mW) [D732]
42 0AV3070125000 AC B Zenner diode(RD10ES 400mW) [D742,D749]
43 0AV3070126000 AC B Zenner diode(RD3.0ES 400mW) [D745,D753]
44 0AV3070130000 AC B ZENNER DIODE(400mW) [D757,D713]
45 0AV3070127000 AC B Zenner diode(RD27ES 400mW) [D761]
46 0AV3050104000 AD B DIODE(1A 40V) [D750,D764]
47 0AV3070141000 AC B ZENNER DIODE(400mW) [D765]
48 0AV2060025000 AK C TEMP.FUSING RESISTOR(4.7Ω5W 142C) [FR701]
49 0AV3090079000 AL B IC(FA5515P) [IC701,IC705]
50 0AV3090041000 AF B IC(UPC1093J-1) [IC702,IC704]
51 0AV3090003000 AM B IC(MB3759P) [IC703]
52 0AV4070063000 AR C Inductor(DRC31-15A202) [L701]
53 0AV4070064000 AL C Inductor(DRB25-05A202) [L702]
54 0AV4120013000 AC C Inductor(T314OP3206536HW) [L703,L710,L715]
55 0AV4050016000 AG C Inductor(PC8T8R2M) [L707]
56 0AV4120008000 AD C Inductor(LFP3A) [L708]
57 0AV4080014000 AL C Inductor [L709]
58 0AV4120002000 AC C Inductor(B-01-A) [L711,L713,L714]
59 0AV4050010000 AH C Inductor(PC8T3R3M) [L712]
60 0AV3082561300 AF B Photo coupler(PS2561) [PC701,PC703,PC704,PC706,PC707]
61 0AV3180000009 AL B PHOTO TRIAC COUPLER [PC702,PC705]
62 0AV3042698000 AS B FET(2SK2698 500V 15A) [Q701]
63 0AV3001015500 AC B Transistor(2SA1015 -50V -150mA) [Q702,Q713]
64 0AV3042543000 AQ B FET(2SK2543 500V 8A) [Q704]
0AV3021815500 AC B Transistor(2SC1815 50V 150mA) [Q706,Q709,Q710,Q711,Q714]
65
0AV3021815500 AC B Transistor(2SC1815 50V 150mA) [Q715,Q717,Q718,Q719,Q723]
66 0AV3040504000 AN B FET(2SJ504) [Q707]
67 0AV3022655500 AE B Transistor(2SC2655) [Q708]
68 0AV3042736000 AN B FET(2SK2736) [Q712]
69 0AV3021002999 AD B Transistor(RN1002) [Q720,Q721,Q722]
70 0AV2022213040 AC C Metal oxide film resistor(RSU01WST5A221J 220Ω 1W) [R701]
71 0AV2054754077 AF C Cement filled resistor(MNS05WNZ4R7J 4.7Ω 5W) [R702]
Flame proof carbon resistor(RDF50S4.7KΩJ 4.7KΩ 1/2W)
72 0AV2014723030 AB C
[R703,R704,R705]
– 28-1 –
X Power supply PWB 100V[AR-M312U,AR-M420U]
Inter- PRICE NEW PART Effective
NO. PARTS CODE change RANK MARK RANK DESCRIPTION TR No. time
Flame proof carbon resistor(RDF16S22KΩJ 22KΩ 1/6W)
73 0AV2012233010 AA C
[R706,R772,R827,R828]
Flame proof carbon resistor
74 0AV2011843030 AB C
(RDF50S180KΩJ 180KΩ 1/2W) [R707]
75 0AV2990106000 AC C METAL OXIDE FILM RESISTOR(27KΩ1W) [R708,R709]
76 0AV2011053010 AB C Flame proof carbon resistor(RDF16S1MΩJ 1MΩ 1/6W) [R710]
Flame proof carbon resistor(RDF16S1KΩJ 1KΩ 1/6W)
77 0AV2011023010 AA C
[R711,R737,R750,R784,R817]
78 0AV2051083055 AE C Cement filled resistor(BPR02WFTR10J 0.1Ω 2W) [R712,R739]
79 0AV2014733020 AB C Flame proof carbon resistor(RDF25S47KΩJ 47KΩ 1/4W) [R713,R714]
Flame proof carbon resistor(RDF50S120ΩJ 120Ω 1/2W)
80 0AV2011213030 AB C
[R715,R732,R726,R728]
81 0AV2011203020 AB C Flame proof carbon resistor(RDF25S12ΩJ 12Ω 1/4W) [R716]
Flame proof carbon resistor(RDF16S10KΩJ 10KΩ 1/6W)
0AV2011033010 AA C
[R717,R730,R735,R741,R753]
82 Flame proof carbon resistor(RDF16S10KΩJ 10KΩ 1/6W)
0AV2011033010 AA C
[R758,R776,R795,R800,R818]
0AV2011033010 AA C Flame proof carbon resistor(RDF16S10KΩJ 10KΩ 1/6W) [R824,R825]
83 0AV2021013078 AF C Metal oxide film resistor(RSS5FB100ΩJ H1 100Ω 5W) [R718,R744]
84 0AV2013323010 AA C Flame proof carbon resistor(RDF16S3.3KΩJ 3.3KΩ 1/6W) [R719,R775]
85 0AV2021213040 AC C METAL OXIDE FILM RESISTOR(120Ω1W) [R720,R731]
86 0AV2018213010 AA C Fusing resistor(RF16S820ΩJ 820Ω 1/6W) [R721]
87 0AV2013933010 AA C Flame proof carbon resistor(RDF16S39KΩJ 39KΩ 1/6W) [R790]
88 0AV2148203040 AC C Metal oxide film resistor(RSS182ΩJ 82Ω 1W) [R723]
89 0AV2012243010 AA C Flame proof carbon resistor(RDF16S220KΩJ 220KΩ 1/6W) [R724]
90 0AV2011013030 AA C Fusing resistor(RF50S100ΩJ 100Ω 1/2WH) [R725,R727]
Flame proof carbon resistor(RDF16S2.2KΩJ 2.2KΩ 1/6W)
0AV2012223010 AA C
[R749,R766,R777,R807,R808]
91
Flame proof carbon resistor(RDF16S2.2KΩJ 2.2KΩ 1/6W)
0AV2012223010 AA C
[R815,R810,R797]
92 0AV2011813010 AA C Flame proof carbon resistor(RDF16S180ΩJ 180Ω 1/6W) [R734,R768]
93 0AV2990105000 AB C METAL FILM RESISTOR(68KΩ 1/6W) [R736]
94 0AV2041213010 AC C Fusing resistor(RF16S120ΩJ 120Ω 1/6W) [R738]
95 0AV2012203020 AA C Flame proof carbon resistor(RDF25S22ΩJ 22Ω 1/4W) [R740]
96 0AV2018233010 AA C Flame proof carbon resistor(RDF16S82KΩJ 82KΩ 1/6W) [R742]
97 0AV2024703078 AF C Metal oxide film resistor(RSS5FB47ΩJ H1 47Ω 5W) [R743]
98 0AV2013333020 AA C Flame proof fixed carbon film resistor(33KΩ 1/4W) [R746,R747]
99 0AV2013333010 AA C Flame proof carbon resistor(RDF16S33KΩJ 33KΩ 1/6W) [R748]
100 0AV2012723010 AA C Flame proof carbon resistor(RDF16S2.7KΩJ 2.7KΩ 1/6W) [R751]
101 0AV2990083000 AC C Metal film resistor(SN16S22.3KΩD 22.3KΩ 1/6W) [R754]
102 0AV2990010000 AC C Metal film resistor(SN16S2.55KΩD 2.55KΩ 1/6W) [R755]
103 0AV2011533010 AA C Flame proof carbon resistor(RDF16S15KΩJ 15KΩ 1/6W) [R756]
104 0AV2012213020 AA C Flame proof carbon resistor(RDF25S220ΩJ 220Ω 1/4W) [R761]
105 0AV2014773020 AA C Flame proof carbon resistor(RDF25S4.7ΩJ 4.7Ω 1/4W) [R762]
106 0AV2014723020 AA C Flame proof carbon resistor(RDF25S4.7KΩJ 4.7KΩ 1/4W) [R763]
107 0AV2051094075 AG C Cement filled resistor(BPR05WFTR10J 0.01Ω 5W) [R764]
108 0AV2015623010 AA C Flame proof carbon resistor(RDF16S5.6KΩJ 5.6KΩ 1/6W) [R765]
109 0AV2041013010 AC C Fusing resistor(RF16S100ΩJ 100Ω 1/6W) [R767]
110 0AV2011213020 AA C Flame proof carbon resistor(RDF25S120ΩJ 120Ω 1/4W) [R769,R771]
111 0AV2011233010 AA C Flame proof carbon resistor(RDF16S12KΩJ 12KΩ 1/6W) [R773]
112 0AV2990084000 AC C Metal film resistor(SN16S1.2KΩD 1.2KΩ 1/6W) [R778]
113 0AV2990085000 AC C Metal film resistor(SN16S39KΩD 39KΩ 1/6W) [R779]
114 0AV2142203040 AC C Metal oxide film resistor(RSF1B22ΩJ 22Ω 1W) [R780]
115 0AV2013313010 AA C Flame proof carbon resistor(RDF16S330ΩJ 330Ω 1/6W) [R781]
116 0AV2011013010 AA C Fixed carbon film resistor(RDF16S100ΩJ 100Ω 1/6W) [R782]
117 0AV2013913010 AA C Flame proof carbon resistor(RDF16S390ΩJ 390Ω 1/6W) [R783]
118 0AV2011223010 AA C Flame proof carbon resistor(RDF16S1.2KΩJ 1.2KΩ 1/6W) [R785]
119 0AV2016813010 AA C Flame proof carbon resistor(RDF16S680ΩJ 680Ω 1/6W) [R786]
120 0AV2011213010 AA C Flame proof carbon resistor(RDF16S120ΩJ 120Ω 1/6W) [R791]
Flame proof carbon resistor(RDF16S470ΩJ 470Ω 1/6W)
121 0AV2014713010 AA C
[R792,R814,R809,R826]
122 0AV2012733010 AA C Flame proof carbon resistor(RDF16S27KΩJ 27KΩ 1/6W) [R793,R794]
123 0AV2015633010 AA C Flame proof carbon resistor(RDF16S56KΩJ 56KΩ 1/6W) [R798]
124 0AV2043313010 AC C Fusing resistor(RF16S330ΩJ 330Ω 1/6W) [R801]
125 0AV2021233040 AC C METAL OXIDE FILM RESISTOR(12KΩ1W) [R804,R805]
126 0AV2141803040 AC C METAL OXIDE FILM RESISTOR(18Ω1W) [R806]
127 0AV2016104020 AB C FLAME PROOF CARBON RESISTOR(100KΩ1/4W) [R811,R812]
Flame proof carbon resistor(RDF16S47KΩJ 47KΩ 1W)
128 0AV2014733010 AA C
[R813,R819,R820]
129 0AV2015633020 AA C FLAME PROOF CARBON RESISTOR(56KΩ 1/4W) [R733]
130 0AV2042203010 AC C Fusing resistor(RF16S22ΩJ 22Ω 1/6W) [R816]
Flame proof carbon resistor(RDF16S4.7KΩJ 4.7KΩ 1/6W)
131 0AV2014723010 AA C
[R821,R822,R752,R759,R774,R799]
132 0AV2011043010 AA C Flame proof carbon resistor(RDF16S100KΩJ 100KΩ 1/6W) [R823]
133 0AV2990104000 AC C METALFILM RESISTOR(56KΩ1/6W) [R745]
134 0AV2041003020 AC C Fusing resistor(10Ω 1/4W) [R829]
135 0AV2990107000 AC C METAL FILM RESISTOR(1.5KΩ 1/6W) [R729]
136 0AV2990112000 AC C METAL FILM RESISTOR(49.9KΩ 1/6W) [R722]
! 137 0AV4000136711 AY B Transformer(N-T01-367) [T701]
– 28-2 –
manuals4you.com
X Power supply PWB 100V[AR-M312U,AR-M420U]
Inter- PRICE NEW PART Effective
NO. PARTS CODE change RANK MARK RANK DESCRIPTION TR No. time
! 138 0AV4000131011 AQ B Transformer(N-T01-310) [T702]
139 0AV3160033000 AP B Traic(TM1641P) [TR701,TR703]
140 0AV3160037000 AN B Traic [TR702]
141 0AV2081029188 AC B Potentiometer(RH063MC13R 1KΩ) [VR701,VR702]
142 0AV5080011000 AP B Relay(ALE15B24) [RL701]
143 0AV5190002000 AF C Varistor(ENC271D-10A-TA-B) [X701]
144 0AV5030126000 AG C Connector(B03P-VL) [CN1]
145 0AV5030127000 AD C Connector(B7B-PH-K-S) [CN2]
146 0AV5030036000 AC C Connector(B2P3-VH) [CN3]
147 0AV5030128000 AD C Connector(B03B-XASK-1) [CN4]
148 0AV5030129000 AK C Connector(B12P-HL-A) [CN5]
149 0AV5130009000 AD C Terminal(TP82224-31)
150 0AV5130011000 AC C Terminal
151 0AV8117730416 AC C Screw(3×8)
152 0AV8117730516 AC C Screw(3×10)
153 0AV8117730616 AC C Screw(3×12)
154 0AV6113116511 AN C Heatsink(LM31165)
155 0AV6114150911 AH C Heatsink
156 0AV6114150111 AG C Heatsink
157 0AV5050005000 AA C Holder(PFC5000-0203)
158 0AV7100003000 AE C Insulation sheet(M-30AD-D-3)
0AV5110012000 AB C Jumper wire(RJ-SKA-06) [RJ701,RJ702,RJ703,RJ708,RJ712]
0AV5110012000 AB C Jumper wire(RJ-SKA-06) [RJ713,RJ721,RJ727,RJ730,RJ735]
159
0AV5110012000 AB C Jumper wire(RJ-SKA-06) [RJ746,RJ760,RJ768,RJ769,RJ771]
0AV5110012000 AB C Jumper wire(RJ-SKA-06) [RJ772,RJ773,RJ775,RJ776]
0AV5110003000 AA C Jumper wire(RJ-SBA-06) [RJ707,RJ722,RJ723,RJ731,RJ736]
160
0AV5110003000 AA C Jumper wire(RJ-SBA-06) [RJ738,RJ739,RJ743,RJ748,RJ778]
0AV5110001000 AA C Jumper wire(RJ-SCA-06) [RJ711,RJ714,RJ716,RJ747,RJ756]
161
0AV5110001000 AA C Jumper wire(RJ-SCA-06) [RJ757,RJ759,RJ770,RJ779]
0AV5110006000 AA C Jumper wire(RJ-SDA-06) [RJ715,RJ718,RJ725,RJ726,RJ742]
162 0AV5110006000 AA C Jumper wire(RJ-SDA-06) [RJ745,RJ752,RJ754,RJ758,RJ763]
0AV5110006000 AA C Jumper wire(RJ-SDA-06) [RJ766,RJ774,RJ777]
163 0AV5110002000 AA C Jumper wire(RJ-SEA-06) [RJ704,RJ728,RJ733,RJ734,RJ753]
164 0AV5110011000 AB C Jumper wire(RJ-SFA-06) [RJ717,RJ729,RJ740,RJ741,RJ765]
0AV5110004000 AA C Jumper wire(RJ-SGA-06) [RJ705,RJ706,RJ709,RJ710,RJ719]
165 0AV5110004000 AA C Jumper wire(RJ-SGA-06) [RJ720,RJ724,RJ732,RJ737,RJ749]
0AV5110004000 AA C Jumper wire(RJ-SGA-06) [RJ750,RJ751,RJ755,RJ761,RJ762]
165 0AV5110004000 AA C Jumper wire(RJ-SGA-06) [RJ764,RJ767]
! 166 0AV5060186000 AD A Fuse(6.3A/125V) [F701,F702]
! 167 0AV5060188000 AE A Fuse(4A/125V) [F703]
! 168 0AV5060190000 AE A Fuse(10A/125V) [F706]
! 169 0AV5060089000 AE A Fuse(396 2 2A/125V) [F705]
(Unit)
! 901 RDENC0020FCZ6 BV E AC/DC power supply PWB 100
– 28-3 –
Y Power supply PWB 200V[Except AR-M312U,AR-M420U]
Inter- PRICE NEW PART Effective
NO. PARTS CODE change RANK MARK RANK DESCRIPTION TR No. time
1 0AV1570000002 AD C FILM CAPACITOR(LE104-L 0.1µF,250V(LE)) [C701]
2 0AV1570000003 AD C FILM CAPACITOR(LE104-C 0.1µF,250V(LE)) [C760,C761]
3 0AV1570000004 AN C FILM CAPACITOR(LE155-C 1.5µF,250V(LE)) [C702]
4 0AV1650000064 AD C CERAMIC CAPACITOR(DE0813E472M-KH) [C703,C704]
5 0AV1570000005 AF C FILM CAPACITOR(LE334-C) [C705]
6 0AV1390000272 AY C AL-ELECTROLYTIC CAPACITOR(LGU2G561MELC) [C706]
CERAMIC CAPACITOR(PRE132R104K50 0.1µF,50V)
0AV1690000133 AC C
[C707,C718,C720,C730,C733]
7
CERAMIC CAPACITOR(PRE132R104K50 0.1µF,50V)
0AV1690000133 AC C
[C742,C752,C756,C759,C765]
CERAMIC CAPACITOR(DE0905-979R102K1K 1000pF,1KV)
8 0AV1610000091 AC C
[C708,C749,C726,C747,C748]
9 0AV1390000261 AC C AL-ELECTROLYTIC CAPACITOR(UPJ1H4R7MDD 4.7µF,50V) [C711]
AL-ELECTROLYTIC CAPACITOR(UPJ1H220MED 22µF,50V)
10 0AV1390000262 AC C
[C712,C766,C768]
11 0AV1690000113 AE C CERAMIC CAPACITOR(DE1610-2E472M-KX 4700pF(KX)) [C713,C767]
12 0AV1480000084 AD C FILM CAPACITOR(CQMY-92MC2A104J 0.1µF,100V) [C714,C715]
CERAMIC CAPACITOR(RPE132R103K50 0.01µF,50V)
13 0AV1690000134 AC C
[C716,C717,C763]
14 0AV1690000138 AC C CERAMIC CAPACITOR(RPE132R472K50 4700pF,50V) [C719,C757]
15 0AV1610000109 AC C CERAMIC CAPACITOR(DE0705-979R331K2K) [C721,C722]
AL-ELECTROLYTIC CAPACITOR(UPJ1V182MHD6 1800µF,35V)
16 0AV1390000263 AC C
[C728,C729]
17 0AV1390000264 AC C AL-ELECTROLYTIC CAPACITOR(UPJ1H010MDD 1µF,50V) [C734,C771]
18 0AV1390000265 AC C AL-ELECTROLYTIC CAPACITOR(UHD1V681MHD 680µF,35V) [C735]
19 0AV1390000266 AG C AL-ELECTROLYTIC CAPACITOR(UHD1V102MHD 1000µF,35V) [C738]
20 0AV1610000090 AD C CERAMIC CAPACITOR(TPZ11R152K1K) [C709,C710]
21 0AV1690000136 AD C CERAMIC CAPACITOR(RPE132R223K50) [C739,C744,C746,C755]
AL-ELECTROLYTIC CAPACITOR(UPJ1H2R2MDD 2.2µF,50V)
22 0AV1390000267 AC C
[C740,C753]
23 0AV1390000268 AC C AL-ELECTROLYTIC CAPACITOR(UHD1C222MHD 2200µF,16V) [C741]
CERAMIC CAPACITOR(RPE132R102K50 1000pF,50V)
24 0AV1690000137 AC C
[C743,C745,C770]
AL-ELECTROLYTIC CAPACITOR(UHD1A562MHD 5600µF,10V)
25 0AV1390000269 AK C
[C750,C751]
26 0AV1390000270 AD C AL-ELECTROLYTIC CAPACITOR(UPJ1V820MED 82µF,35V) [C754]
27 0AV1480000107 AE C FILM CAPACITOR(ECQE2104RJF 0.1µF,400V) [C764]
28 0AV1390000271 AC C AL-ELECTROLYTIC CAPACITOR(UPJ1C101MED 100µF,16V) [C772]
29 0AV1690000095 AD B CERAMIC CAPACITOR(TRPE132R12K50) [C773]
30 0AV3060035000 AE B DIODE(S1WB(A)60 1A,600V) [D701]
31 0AV3070123000 AC B ZENER DIODE(RD6.8ES 400mW) [D702]
32 0AV3060047000 AC B DIODE(ERA15-06) [D703,D704,D748,D763]
0AV3050019000 AF B DIODE(ERA91-02 0.5A,200V) [D706,D708,D710,D717,D746]
34
0AV3050019000 AF B DIODE(ERA91-02 0.5A,200V) [D747,D755,D758,D759]
0AV3050091000 AB B DIODE(1SS270 60V,150mA) [D707,D714,D726,D727,D728]
0AV3050091000 AB B DIODE(1SS270 60V,150mA) [D731,D733,D737,D738,D743]
35
0AV3050091000 AB B DIODE(1SS270 60V,150mA) [D744,D751,D751,D752]
0AV3050091000 AB B DIODE(1SS270 60V,150mA) [D754,D760,D762]
36 0AV3070085000 AC B ZENER DIODE(RD33ES 400mW) [D709]
37 0AV3070102000 AC B ZENER DIODE(RD39ES) [D712,D756]
38 0AV3070056000 AD B ZENER DIODE(RD20ES 400mW) [D716]
39 0AV3070013000 AB B ZENER DIODE(RD5.6ES 400mW) [D715,D720,D734,D736,D739]
40 0AV3050087000 AN B DIODE(YG906C2R 20A,200V) [D721]
41 0AV3070061000 AC B ZENER DIODE(RD4.7ES 400mW) [D724]
42 0AV3050070000 AK B DIODE(YG802C06 10A,60V) [D729]
43 0AV3050080000 AP B DIODE(YG805C04 20A,40V) [D730]
44 0AV3070081000 AC B ZENER DIODE(RD3.9ES 400mW) [D732]
45 0AV3070131000 AD B ZENER DIODE(RD62E) [D735]
47 0AV3070056000 AD B ZENER DIODE(RD20ES 400mW) [D749]
48 0AV3070112000 AC B ZENER DIODE(RD3.0ES 400mW) [D745,D753]
49 0AV3070023000 AE B ZENER DIODE(RD24ES 400mW) [D713,D757]
50 0AV3070049000 AB B ZENER DIODE(RD27ES 400mW) [D761]
51 0AV3070156000 AC B ZENER DIODE(RD4.3ES 400mW) [D765]
52 0AV3050104000 AD B DIODE(AK04) [D750,D764]
53 0AV3090079000 AL B IC(FA5515P) [IC701,IC705]
54 0AV3090041000 AF B IC(UPC1093J-1) [IC702,IC704]
55 0AV3090008000 AK B IC(MB3759P) [IC703]
56 0AV4070066000 AR C INDUCTOR(DRC31-08A402) [L701]
57 0AV4070067000 AM C INDUCTOR(DRB25-03A502) [L702]
58 0AV4120013000 AC C INDUCTOR(T314OP3206536HW) [L703,L710]
59 0AV4050016000 AG C INDUCTOR(PC8T8R2M) [L707]
60 0AV4120008000 AD C INDUCTOR(LFP3A) [L708]
61 0AV4080011400 AL C INDUCTOR(HK-10S100-4500S) [L709]
62 0AV4120002000 AC C INDUCTOR(B-01-A) [L711,L713,L714,L715]
63 0AV4050010000 AH C INDUCTOR(PC8T3R3M) [L712]
64 0AV3080421100 AE B PHOTO COUPLER(TLP421) [PC701,PC703,PC704,PC706]
65 0AV3180000009 AL B PHOTO TRIAC COUPLER(PC3SF11YV) [PC702,PC705]
66 0AV3042611000 AU B FET(2SK2611) [Q701]
67 0AV3001015500 AC B TRANSISTOR(2SA1015 -50V,-150mA) [Q702,Q713]
68 0AV3042717000 AR B FET(2SK2717) [Q704]
– 29-1 –
manuals4you.com
Y Power supply PWB 200V[Except AR-M312U,AR-M420U]
Inter- PRICE NEW PART Effective
NO. PARTS CODE change RANK MARK RANK DESCRIPTION TR No. time
0AV3021815500 AC B TRANSISTOR(2SC1815 50V 150mA) [Q706,Q709,Q710,Q711,Q714]
69
0AV3021815500 AC B TRANSISTOR(2SC1815 50V 150mA) [Q715,Q717,Q718,Q719,Q723]
70 0AV3040504000 AN B FET(2SJ504) [Q707]
71 0AV3022655500 AE B TRANSISTOR(2SC2655) [Q708]
72 0AV3042736000 AN B FET(2SK2736) [Q712]
73 0AV3021002999 AD B TRANSISTOR(RN1002) [Q720,Q721,Q722]
74 0AV2024713040 AC C METAL OXIDE FILM RESISTOR(RSU01WST5A471J) [R701]
75 0AV2051064077 AF C CEMENT FILLED RESISTOR(MNS05WNZ100J) [R702]
FLAME PROOF CARBON RESISTOR(RDF50S27KΩJ)
76 0AV2012733030 AB C
[R703,R704,R705]
FLAME PROOF CARBON RESISTOR(RDF16S22KΩJ 22KΩ,1/6W)
77 0AV2012233010 AA C
[R706,R772,R827,R828]
FLAME PROOF CARBON RESISTOR(RDF50S180KΩJ 180Ω 1/2W)
78 0AV2011843030 AB C
[R707]
79 0AV2990118000 AC C METAL OXIDE FILM RESISTOR(SPF01W82KΩF) [R708,R709]
80 0AV2011853010 AB C FLAME PROOF CARBON RESISTOR(RDF16S1.8MΩJ) [R710]
FLAME PROOF CARBON RESISTOR(RDF16S1KΩJ 1KΩ,1/6W)
81 0AV2011023010 AA C
[R711,R737,R750,R784,R817,R751]
82 0AV2052294055 AE C CEMENT FILLED RESISTOR(BPR02WFTR22J) [R739]
FLAME PROOF CARBON RESISTOR(RDF25S220KΩJ)
83 0AV2012243020 AA C
[R713,R714,R811,R812]
FLAME PROOF CARBON RESISTOR(RDF50S120ΩJ 120Ω 1/2W)
84 0AV2011213030 AB C
[R715,R732,R726,R728]
85 0AV2011203020 AB C FLAME PROOF CARBON RESISTOR(RDF25S12ΩJ 12Ω1/4W) [R716]
FLAME PROOF CARBON RESISTOR(RDF16S10KΩJ 10KΩ,1/6W)
86 0AV2011033010 AA C
[R717,R730,R735,R741,R753,R758]
METAL OXIDE FILM RESISTOR(RSS5FB100ΩJH1 100Ω 5W)
87 0AV2021013078 AF C
[R718,R744]
FLAME PROOF CARBON RESISTOR(RDF16S3.3KΩJ 3.3KΩ 1/6W)
88 0AV2013323010 AA C
[R719,R775]
89 0AV2021213040 AC C METAL OXIDE FILM RESISTOR(RSF1B120ΩJ 120Ω 1W) [R720,R731]
90 0AV2990142000 AA C METAL FILM RESISTOR(SN16S909ΩD 909Ω 1/6W) [R721]
FLAME PROOF CARBON RESISTOR(RDF16S39KΩJ 39KΩ,1/6W)
91 0AV2013933010 AA C
[R790]
92 0AV2148203040 AC C METAL OXIDE FILM RESISTOR(RSS182ΩJ 82Ω 1W) [R723]
FLAME PROOF CARBON RESISTOR(RDF16S220KΩJ 220KΩ,1/6W)
93 0AV2012243010 AA C
[R724]
94 0AV2011013020 AA B FUSING RESISTOR(RF25S100ΩJ) [R725,R727]
95 0AV2990098000 AD C METAL OXIDE FILM RESISTOR(RSMF2BR22F) [R712]
FLAME PROOF CARBON RESISTOR(RDF16S2.2KΩJ 2.2KΩ,1/6W)
0AV2012223010 AA C
[R749,R766,R777,R807,R808]
96
FLAME PROOF CARBON RESISTOR(RDF16S2.2KΩJ 2.2KΩ,1/6W)
0AV2012223010 AA C
[R815,R810,R797]
FLAME PROOF CARBON RESISTOR(RDF16S180ΩJ 180Ω,1/6W)
97 0AV2011813010 AA C
[R768]
98 0AV2990105000 AB C METAL FILM RESISTOR(SN16S68KΩD 68KΩ,1/6W) [R736]
99 0AV2041513010 AC B FUSING RESISTOR(RF16S150ΩJ) [R738]
100 0AV2012203020 AA C FLAME PROOF CARBON RESISTOR(RDF25S22ΩJ 22Ω 1/4W) [R740]
FLAME PROOF CARBON RESISTOR(RDF16S82KΩJ 82KΩ,1/6W)
101 0AV2018233010 AA C
[R742]
102 0AV2024703078 AF C METAL OXIDE FILM RESISTOR(RSS5FB47ΩJH1 47Ω 5W) [R743]
103 0AV2012743020 AB C FLAME PROOF CARBON RESISTOR(RDF25S270KΩJ) [R746,R747]
FLAME PROOF CARBON RESISTOR(RDF16S33KΩJ 33KΩ 1/6W)
104 0AV2013333010 AA C
[R748]
105 0AV2990090000 AC C METAL FILM RESISTOR(SN16S180ΩD) [R734]
106 0AV2990083000 AC C METAL FILM RESISTOR(SN16S22.3KΩD 22.3KΩ 1/6W) [R754]
107 0AV2990010000 AC C METAL FILM RESISTOR(SN16S2.55KΩD 2.55KΩ 1/6W) [R755]
FLAME PROOF CARBON RESISTOR(RDF16S15KΩJ 15KΩ 1/6W)
108 0AV2011533010 AA C
[R756]
FLAME PROOF CARBON RESISTOR(RDF25S220ΩJ 220Ω 1/4W)
109 0AV2012213020 AA C
[R761]
110 0AV2014773020 AA C FLAME PROOF CARBON RESISTOR(RDF25S4.7ΩJ 4.7Ω 1/4W) [R762]
111 0AV2014723020 AA C FLAME PROOF CARBON RESISTOR(RDF25S4.7KΩJ) [R763]
112 0AV2051094075 AG C CEMENT FILLED RESISTOR(BPR05WFTR10J 0.01Ω 5W) [R764]
FLAME PROOF CARBON RESISTOR(RDF16S5.6KΩJ 5.6KΩ 1/6W)
113 0AV2015623010 AA C
[R765]
114 0AV2041013010 AC B FUSING RESISTOR(RF16S100ΩJ 100Ω 1/6W) [R767]
FLAME PROOF CARBON RESISTOR(RDF25S120ΩJ 120Ω 1/4W)
115 0AV2011213020 AA C
[R769,R771]
FLAME PROOF CARBON RESISTOR(RDF16S12KΩJ 12KΩ 1/6W)
116 0AV2011233010 AA C
[R773]
117 0AV2990084000 AC C METAL FILM RESISTOR(SN16S1.2KΩD 1.2KΩ 1/6W) [R778]
118 0AV2990085000 AC C METAL FILM RESISTOR(SN16S39KΩD 39KΩ 1/6W) [R779]
119 0AV2142203040 AC C METAL OXIDE FILM RESISTOR(RSF1B22ΩJ 22Ω 1W) [R780]
FLAME PROOF CARBON RESISTOR(RDF16S330ΩJ 330Ω 1/6W)
120 0AV2013313010 AA C
[R781]
FLAME PROOF CARBON RESISTOR(RDF16S100ΩJ 100Ω 1/6W)
121 0AV2011013010 AA C
[R782]
FLAME PROOF CARBON RESISTOR(RDF16S390ΩJ 390Ω 1/6W)
122 0AV2013913010 AA C
[R783]
FLAME PROOF CARBON RESISTOR(RDF16S1.2KΩJ 1.2KΩ 1/6W)
123 0AV2011223010 AA C
[R785]
– 29-2 –
Y Power supply PWB 200V[Except AR-M312U,AR-M420U]
Inter- PRICE NEW PART Effective
NO. PARTS CODE change RANK MARK RANK DESCRIPTION TR No. time
FLAME PROOF CARBON RESISTOR(RDF16S680ΩJ 680Ω 1/6W)
124 0AV2016813010 AA C
[R786]
FLAME PROOF CARBON RESISTOR(RDF16S120ΩJ 120Ω 1/6W)
125 0AV2011213010 AA C
[R791]
FLAME PROOF CARBON RESISTOR(RDF16S470ΩJ)
126 0AV2014713010 AA C
[R792,R814,R809,R826]
127 0AV2012733010 AA C FLAME PROOF CARBON RESISTOR(RDF16S27KΩJ) [R793,R794]
128 0AV2015633010 AA C FLAME PROOF CARBON RESISTOR(RDF16S56KΩJ) [R798]
129 0AV2043313010 AC B FUSING RESISTOR(RF16S330ΩJ) [R801]
130 0AV2023333040 AC C METAL OXIDE FILM RESISTOR(RSF1B33KΩJ) [R804,R805]
131 0AV2142703040 AC C METAL OXIDE FILM RESISTOR(RSMF1B27J) [R806]
FLAME PROOF CARBON RESISTOR(RDF16S47KΩJ)
132 0AV2014733010 AA C
[R813,R819,R820]
133 0AV2015633020 AA C FLAME PROOF CARBON RESISTOR(RDF25S56KΩJ) [R733]
134 0AV2042203010 AC B FUSING RESISTOR(RF16S22ΩJ) [R816]
FLAME PROOF CARBON RESISTOR(RDF16S4.7KΩJ)
135 0AV2014723010 AA C
[R821,R822,R752,R759,R774,R799]
136 0AV2011043010 AA C FLAME PROOF CARBON RESISTOR(RDF16S100KΩJ) [R823]
137 0AV2990104000 AC C METAL FILM RESISTOR(SN16S56KΩD) [R745]
138 0AV2041003020 AC B FUSING RESISTOR(RF25S10ΩJ) [R829]
139 0AV2990107000 AC C METAL FILM RESISTOR(SN16S1.5KΩD) [R729]
140 0AV2990112000 AC C METAL FILM RESISTOR(SN16S49.9KΩD) [R722]
FLAME PROOF CARBON RESISTOR(RDF16S2.2KΩJ 2.2KΩ,1/6W)
141 0AV2012223010 AA C
[R760]
142 0AV2060026000 AK B TEMP.FUSING RESISTOR(MEG05N100KB142) [FR701]
! 143 0AV4000139011 AX B Transformer(N-T01-390) [T701]
! 144 0AV4000138911 AQ B Transformer(N-T01-389) [T702]
145 0AV3160034000 AQ B Traic(TM1661P) [TR701,TR703]
146 0AV3160032000 AN B Traic(BCR8PM-12LP) [TR702]
147 0AV2081029188 AC B POTENTIOMETER(RH063MC13R) [VR701,VR702]
148 0AV5080013000 AP B RELAY(OMIH-SS-124LM) [RL701]
149 0AV5190003000 AF B Varistor(ENC471D-10A-TA-B) [X701]
150 0AV5030126000 AG C Connector(B03P-VL) [CN1]
151 0AV5030127000 AD C Connector(B7B-PH-K-S) [CN2]
152 0AV5030128000 AD C Connector(B03B-XASK-1) [CN4]
153 0AV5030129000 AK C Connector(B12P-HL-A) [CN5]
154 0AV5030149000 AE C Connector(B5P-VH) [CN6]
155 0AV5030088000 AD C Connector(B2P-VH) [CN7]
156 0AV5130009000 AD C TERMINAL(TP82224-31)
157 0AV5130011000 AC C TERMINAL(TP00370-21)
158 0AV8117730416 AC C SCREW(NACPEW-B3X8SF)
159 0AV8117730516 AC C SCREW(NACPEW-B3X10SF)
160 0AV8117730616 AC C SCREW(NACPEW-B3X12SF)
161 0AV6113116511 AN C HEATSINK(LM31165)
162 0AV6114150911 AH C HEATSINK(LM41509)
163 0AV6114150111 AG C HEATSINK(LM41510)
164 0AV5050005000 AA C HOLDER(PFC5000-0203)
165 0AV7100003000 AE C INSULATION SHEET(M-30AD-D-3)
0AV5110012000 AB C Jumper wire(RJ-SKA-06) [RJ701,RJ702,RJ703,RJ708,RJ712]
0AV5110012000 AB C Jumper wire(RJ-SKA-06) [RJ713,RJ721,RJ727,RJ730,RJ735]
166
0AV5110012000 AB C Jumper wire(RJ-SKA-06) [RJ746,RJ760,RJ768,RJ769,RJ771]
0AV5110012000 AB C Jumper wire(RJ-SKA-06) [RJ772,RJ773,RJ775,RJ776]
0AV5110003000 AA C Jumper wire(RJ-SBA-06) [RJ707,RJ722,RJ723,RJ731,RJ736]
167
0AV5110003000 AA C Jumper wire(RJ-SBA-06) [RJ738,RJ739,RJ743,RJ748,RJ778]
0AV5110001000 AA C Jumper wire(RJ-SCA-06) [RJ711,RJ714,RJ716,RJ747]
168
0AV5110001000 AA C Jumper wire(RJ-SCA-06) [RJ756,RJ757,RJ759,RJ770,RJ779]
0AV5110006000 AA C Jumper wire(RJ-SDA-06) [RJ715,RJ718,RJ725,RJ726,RJ742]
169 0AV5110006000 AA C Jumper wire(RJ-SDA-06) [RJ745,RJ752,RJ754,RJ758,RJ763]
0AV5110006000 AA C Jumper wire(RJ-SDA-06) [RJ766,RJ774,RJ777]
170 0AV5110002000 AA C Jumper wire(RJ-SEA-06) [RJ704,RJ728,RJ733,RJ734,RJ753]
171 0AV5110011000 AB C Jumper wire(RJ-SFA-06) [RJ717,RJ729,RJ740,RJ741,RJ765]
0AV5110004000 AA C Jumper wire(RJ-SGA-06) [RJ705,RJ706,RJ709,RJ710]
0AV5110004000 AA C Jumper wire(RJ-SGA-06) [RJ719,RJ720,RJ724,RJ732]
172 0AV5110004000 AA C Jumper wire(RJ-SGA-06) [RJ737,RJ749,RJ750,RJ751]
0AV5110004000 AA C Jumper wire(RJ-SGA-06) [RJ755,RJ761,RJ762,RJ764]
0AV5110004000 AA C Jumper wire(RJ-SGA-06) [RJ767,RJ780,RJ781]
! 173 0AV5060093000 AF A FUSE(6.3A/250V) [F701,F702,F704,F706]
! 174 0AV5060094000 AE A FUSE(4A/250V) [F703]
! 175 0AV5060095000 AF A FUSE(MRT2.0) [F705]
(Unit)
! 901 RDENC0037FCZ3 BX E AC/DC power supply PWB 200
– 29-3 –
manuals4you.com
Z Power supply PWB 200V[AR-M312U,AR-M420U]
Inter- PRICE NEW PART Effective
NO. PARTS CODE change RANK MARK RANK DESCRIPTION TR No. time
1 0AV1560000009 AE C Film capacitor(RE104-L 0.1µF 250V(RE)) [C701]
2 0AV1560000002 AD C Film capacitor(RE104-C 0.1µF 250V(RE)) [C760,C761]
3 0AV1560000008 AR C Film capacitor(RE155-C 1.5µF 250V(RE)) [C702]
4 0AV1690000074 AD C Ceramic capacitor(DE0807E102M-KH 1000PF(KH)) [C703,C704]
5 0AV1560000004 AG C FILM CAPACITOR(0.33µF 250V(RE)) [C705]
6 0AV1390000272 AY C AL-ELECTROLYTIC CAPACITOR(560µF 400V) [C706]
0AV1690000133 AC C CERAMIC CAPACITOR(0.1µF 50V) [C707,C718,C720,C730,C733]
7
0AV1690000133 AC C CERAMIC CAPACITOR(0.1µF 50V) [C742,C752,C756,C759,C765]
Ceramic capacitor(DE0905-979R102K1K 1000PF 1KV)
8 0AV1610000091 AC C
[C708,C726,C747,C748,C749]
9 0AV1610000090 AD C CERAMIC CAPACITOR(1500PF 1KV) [C709,C710]
10 0AV1390000261 AC C AL-ELECTROLYTIC CAPACITOR(4.7µF 50V) [C711]
11 0AV1390000262 AC C AL-ELECTROLYTIC CAPACITOR(22µF 50V) [C712,C766,C768]
12 0AV1690000113 AE C Ceramic capacitor(DE1610-2E472M-KX 4700PF(KX)) [C713,C767]
13 0AV1480000109 AD C FILM CAPACITOR(0.1µF 50V) [C714,C715]
14 0AV1690000134 AC C CERAMIC CAPACITOR(0.01µF 50V) [C716,C717,C763]
15 0AV1690000138 AC C CERAMIC CAPACITOR(4700PF 50V) [C719,C757]
16 0AV1610000039 AB C Ceramic capacitor(330pF 2KV) [C721,C722]
17 0AV1390000263 AC C AL-ELECTROLYTIC CAPACITOR(1800µF 35V) [C728,C729]
18 0AV1390000264 AC C AL-ELECTROLYTIC CAPACITOR(1µF 50V) [C734,C771]
19 0AV1390000265 AC C AL-ELECTROLYTIC CAPACITOR(680µF 35V) [C735]
20 0AV1390000266 AG C AL-ELECTROLYTIC CAPACITOR(1000µF 35V) [C738]
21 0AV1690000136 AD C CERAMIC CAPACITOR(0.022µF 50V) [C739,C744,C746,C755]
22 0AV1390000267 AC C AL-ELECTROLYTIC CAPACITOR(2.2µF 50V) [C740,C753]
23 0AV1390000268 AC C AL-ELECTROLYTIC CAPACITOR(2200µF 16V) [C741]
24 0AV1690000137 AC C CERAMIC CAPACITOR(1000PF 50V) [C743,C745,C770,C773]
25 0AV1390000269 AK C AL-ELECTROLYTIC CAPACITOR(5600µF 10V) [C750,C751]
26 0AV1390000270 AD C AL-ELECTROLYTIC CAPACITOR(82µF 35V) [C754]
27 0AV1480000107 AE C FILM CAPACITOR(0.1µF 400V) [C764]
28 0AV1390000271 AC C AL-ELECTROLYTIC CAPACITOR(100µF 16V) [C772]
29 0AV3060035000 AE B Diode(S1WB(A)60 1A 600V) [D701]
30 0AV3070123000 AC B Zenner diode(RD6.8ES 400mw) [D702]
manuals4you.com
– 30-1 –
Z Power supply PWB 200V[AR-M312U,AR-M420U]
Inter- PRICE NEW PART Effective
NO. PARTS CODE change RANK MARK RANK DESCRIPTION TR No. time
75 0AV2012733030 AB C FLAME PROOF CARBON RESISTOR(27KΩ 1/2W) [R703,R704,R705]
Flame proof carbon resistor(RDF16S22KΩJ 22KΩ 1/6W)
76 0AV2012233010 AA C
[R706,R772,R827,R828]
77 0AV2011843030 AB C Flame proof carbon resistor(RDF50S180KΩJ 180KΩ 1/2W) [R707]
78 0AV2990118000 AC C METAL OXIDE FILM RESISTOR(82KΩ1W) [R708,R709]
79 0AV2011853010 AB C FLAME PROOF CARBON RESISTOR(1.8MΩ1/6W) [R710]
Flame proof carbon resistor(RDF16S1KΩJ 1KΩ 1/6W)
80 0AV2011023010 AA C
[R711,R737,R750,R784,R817]
81 0AV2052294055 AE C CEMENT FILLED RESISTOR(0.22Ω2W) [R712,R739]
Fixed carbon film resistor(RDF25S220KΩJ 220KΩ 1/4W)
82 0AV2012243020 AA C
[R713,R714,R811,R812]
Flame proof carbon resistor(RDF50S120ΩJ 120Ω 1/2W)
83 0AV2011213030 AB C
[R715,R726,R728,R732]
84 0AV2011203020 AB C Flame proof carbon resistor(RDF25S12ΩJ 12Ω 1/4W) [R716]
Flame proof carbon resistor(RDF16S10KΩJ 10KΩ 1/6W)
0AV2011033010 AA C
[R717,R730,R735,R741,R753]
85 Flame proof carbon resistor(RDF16S10KΩJ 10KΩ 1/6W)
0AV2011033010 AA C
[R758,R776,R795,R800,R818]
0AV2011033010 AA C Flame proof carbon resistor(RDF16S10KΩJ 10KΩ 1/6W) [R824,R825]
86 0AV2021013078 AF C Metal oxide film resistor(RSS5FB100ΩJ H1 100Ω 5W) [R718,R744]
87 0AV2013323010 AA C Flame proof carbon resistor(RDF16S3.3KΩJ 3.3KΩ 1/6W) [R719,R775]
88 0AV2021213040 AC C METAL OXIDE FILM RESISTOR(120Ω 1W) [R720,R731]
89 0AV2990099000 AC C METAL FILM RESISTOR(942Ω 1/6W) [R721]
90 0AV2013933010 AA C Flame proof carbon resistor(RDF16S39KΩJ 39KΩ 1/6W) [R790]
91 0AV2148203040 AC C Metal oxide film resistor(RSS182ΩJ 82Ω 1W) [R723]
92 0AV2012243010 AA C Flame proof carbon resistor(RDF16S220KΩJ 220KΩ 1/6W) [R724]
93 0AV2011013020 AA C Flame proof fixed carbon film resistor(100Ω 1/4W) [R725,R727]
Flame proof carbon resistor(RDF16S2.2KΩJ 2.2KΩ 1/6W)
0AV2012223010 AA C
[R749,R760,R766,R777,R797]
94
Flame proof carbon resistor(RDF16S2.2KΩJ 2.2KΩ 1/6W)
0AV2012223010 AA C
[R815,R807,R808,R810]
95 0AV2015633020 AA C FLAME PROOF CARBON RESISTOR(56KΩ 1/6W) [R733]
96 0AV2011813010 AA C Flame proof carbon resistor(RDF16S180ΩJ 180Ω 1/6W) [R768]
97 0AV2990105000 AB C METAL FILM RESISTOR(68KΩ 1/6W) [R736]
98 0AV2041513010 AC C Fusing resistor(150Ω 1/6W) [R738]
99 0AV2012203020 AA C Flame proof carbon resistor(RDF25S22ΩJ 22Ω 1/4W) [R740]
100 0AV2018233010 AA C Flame proof carbon resistor(RDF16S82KΩJ 82KΩ 1/6W) [R742]
101 0AV2024703078 AF C Metal oxide film resistor(RSS5FB47ΩJ H1 47Ω 5W) [R743]
102 0AV2012743020 AB C Flame proof fixed carbon film resistor(270KΩ 1/4W) [R746,R747]
103 0AV2013333010 AA C Flame proof carbon resistor(RDF16S33KΩJ 33KΩ 1/6W) [R748]
104 0AV2012733010 AA C Flame proof carbon resistor(RDF16S27KΩJ 2.7KΩ 1/6W) [R751]
105 0AV2990083000 AC C Metal film resistor(SN16S22.3KΩD 22.3KΩ 1/6W) [R754]
106 0AV2990010000 AC C Metal film resistor(SN16S2.55KΩD 2.55KΩ 1/6W) [R755]
107 0AV2011533010 AA C Flame proof carbon resistor(RDF16S15KΩJ 15KΩ 1/6W) [R756]
108 0AV2012203020 AA C Flame proof carbon resistor(RDF25S22ΩJ 220Ω 1/4W) [R761]
109 0AV2014773020 AA C Flame proof carbon resistor(RDF25S4.7ΩJ 4.7Ω 1/4W) [R762]
110 0AV2014723020 AA C Flame proof carbon resistor(RDF25S4.7KΩJ 4.7KΩ 1/4W) [R763]
111 0AV2051094075 AG C Cement filled resistor(BPR05WFTR10J 0.01Ω 5W) [R764]
112 0AV2015623010 AA C Flame proof carbon resistor(RDF16S5.6KΩJ 5.6KΩ 1/6W) [R765]
113 0AV2041013010 AC C Fusing resistor(RF16S100ΩJ 100Ω 1/6W) [R767]
114 0AV2011213020 AA C Flame proof carbon resistor(RDF25S120ΩJ 120Ω 1/4W) [R769,R771]
115 0AV2011233010 AA C Flame proof carbon resistor(RDF16S12KΩJ 12KΩ 1/6W) [R773]
116 0AV2990084000 AC C Metal film resistor(SN16S1.2KΩD 1.2KΩ 1/6W) [R778]
117 0AV2990085000 AC C Metal film resistor(SN16S39KΩD 39KΩ 1/6W) [R779]
118 0AV2142203040 AC C Metal oxide film resistor(RSF1B22ΩJ 22Ω 1W) [R780]
119 0AV2013303010 AA C Flame proof carbon resistor(33Ω 1/6W) [R781]
120 0AV2011003010 AA C Flame proof carbon resistor(RDF16S100ΩJ 100Ω 1/6W) [R782]
121 0AV2013903010 AB C FLAME PROOF CARBON RESISTOR(390Ω 1/6W) [R783]
122 0AV2011223010 AA C Flame proof carbon resistor(RDF16S1.2KΩJ 1.2KΩ 1/6W) [R785]
123 0AV2016813010 AA C Flame proof carbon resistor(RDF16S680ΩJ 680Ω 1/6W) [R786]
124 0AV2011203010 AC C FLAME PROOF CARBON RESISTOR(120Ω1/6W) [R791]
Flame proof carbon resistor(RDF16S470ΩJ 470Ω 1/6W)
125 0AV2014713010 AA C
[R792,R809,R814,R826]
126 0AV2012733010 AA C Flame proof carbon resistor(RDF16S27KΩJ 27KΩ 1/6W) [R793,R794]
127 0AV2015633010 AA C Flame proof carbon resistor(RDF16S56KΩJ 56KΩ 1/6W) [R798]
128 0AV2043313010 AC C Fusing resistor(RF16S330ΩJ 330Ω 1/6W) [R801]
129 0AV2023333040 AC C METAL OXIDE FILM RESISTOR(33KΩ1W) [R804,R805]
130 0AV2142703040 AC C METAL OXIDE FILM RESISTOR(27Ω1W) [R806]
Flame proof carbon resistor(RDF16S47KΩJ 47KΩ 1/6W)
131 0AV2014733010 AA C
[R813,R819,R820]
132 0AV2042203010 AC C Fusing resistor(RF16S22ΩJ 22Ω 1/6W) [R816]
Flame proof carbon resistor(RDF16S4.7KΩJ 4.7KΩ 1/6W)
133 0AV2014723010 AA C
[R752,R759,R774,R799,R821,R822]
134 0AV2011043010 AA C Flame proof carbon resistor(RDF16S100KΩJ 100KΩ 1/6W) [R823]
135 0AV2990090000 AC C METAL FILM RESISTOR(180Ω 1/6W) [R734]
136 0AV2990119000 AC C METAL FILM RESISTOR(1.6KΩ 1/6W) [R729]
137 0AV2990104000 AC C METAL FILM RESISTOR(56KΩ 1/6W) [R745]
138 0AV2041003020 AC C Fusing resistor(10Ω 1/4W) [R829]
139 0AV2990112000 AC C METAL FILM RESISTOR(49.9KΩ 1/6W) [R722]
! 140 0AV4000139011 AX B Transformer(N-T01-390) [T701]
! 141 0AV4000138911 AQ B Transformer(N-T01-389) [T702]
manuals4you.com
Z Power supply PWB 200V[AR-M312U,AR-M420U]
Inter- PRICE NEW PART Effective
NO. PARTS CODE change RANK MARK RANK DESCRIPTION TR No. time
142 0AV3160034000 AQ B Triac(TM1641PLF113) [TR701,TR703]
143 0AV3160032000 AN B Traic(BCR8KM-12LA) [TR702]
144 0AV2081029188 AC B Potentiometer(RH063MC13R 1KΩ) [VR701,VR702]
145 0AV5080011000 AP B Relay(ALE15B24) [RL701]
146 0AV5190003000 AF C Varistor(ENC471D-10A) [X701]
147 0AV5030126000 AG C Connector(B03P-VL) [CN1]
148 0AV5030127000 AD C Connector(B7B-PH-K-S) [CN2]
149 0AV5030036000 AC C Connector(B2P3-VH) [CN3]
150 0AV5030128000 AD C Connector(B03B-XASK-1) [CN4]
151 0AV5030129000 AK C Connector(B12P-HL-A) [CN5]
152 0AV5130009000 AD C Terminal(TP82224-31)
153 0AV5130011000 AC C Terminal(TP00370-21)
154 0AV8117730416 AC C Screw(3×8)
155 0AV8117730516 AC C Screw(3×10)
156 0AV8117730616 AC C Screw(3×12)
157 0AV6113116511 AN C Heatsink(LM31165)
158 0AV6114150911 AH C Heatsink(LM41509)
159 0AV6114150111 AG C Heatsink(LM41510)
160 0AV5050005000 AA C Holder(PFC5000-0203)
161 0AV7100003000 AE C Insulation sheet(M-30AD-D-3)
0AV5110012000 AB C Jumper wire(RJ-SKA-06) [RJ701,RJ702,RJ703,RJ708,RJ712]
0AV5110012000 AB C Jumper wire(RJ-SKA-06) [RJ713,RJ721,RJ727,RJ730,RJ735]
162
0AV5110012000 AB C Jumper wire(RJ-SKA-06) [RJ746,RJ760,RJ768,RJ769,RJ771]
0AV5110012000 AB C Jumper wire(RJ-SKA-06) [RJ772,RJ773,RJ775,RJ776]
0AV5110003000 AA C Jumper wire(RJ-SBA-06) [RJ707,RJ722,RJ723,RJ731,RJ736]
163
0AV5110003000 AA C Jumper wire(RJ-SBA-06) [RJ738,RJ739,RJ743,RJ748,RJ778]
0AV5110001000 AA C Jumper wire(RJ-SCA-06) [RJ711,RJ714,RJ716,RJ747,RJ756]
164
0AV5110001000 AA C Jumper wire(RJ-SCA-06) [RJ757,RJ759,RJ770,RJ779]
0AV5110006000 AA C Jumper wire(RJ-SDA-06) [RJ715,RJ718,RJ725,RJ726,RJ742]
165 0AV5110006000 AA C Jumper wire(RJ-SDA-06) [RJ745,RJ752,RJ754,RJ758,RJ763]
0AV5110006000 AA C Jumper wire(RJ-SDA-06) [RJ766,RJ774,RJ777]
166 0AV5110002000 AA C Jumper wire(RJ-SEA-06) [RJ704,RJ728,RJ733,RJ734,RJ753]
167 0AV5110011000 AB C Jumper wire(RJ-SFA-06) [RJ717,RJ729,RJ740,RJ741,RJ765]
0AV5110004000 AA C Jumper wire(RJ-SGA-06) [RJ705,RJ706,RJ709,RJ710,RJ719]
0AV5110004000 AA C Jumper wire(RJ-SGA-06) [RJ720,RJ724,RJ732,RJ737,RJ749]
168
0AV5110004000 AA C Jumper wire(RJ-SGA-06) [RJ750,RJ751,RJ755,RJ761,RJ762]
0AV5110004000 AA C Jumper wire(RJ-SGA-06) [RJ764,RJ767,RJ780,RJ781]
! 169 0AV5060093000 AF A Fuse(6.3A/250V) [F701,F702,706]
! 170 0AV5060094000 AE A Fuse(4A/250V) [F703]
! 171 0AV5060095000 AF A Fuse(2A/250V) [F705]
(Unit)
! 901 RDENC0021FCZ6 BW E AC/DC power supply PWB 200
– 30-3 –
[ Exteriors[AR-EF3/5/6]
Inter- PRICE NEW PART Effective
NO. PARTS CODE change RANK MARK RANK DESCRIPTION TR No. time
1 GCAB-0943FCNZ AH D Rear lower cabinet
2 XHBS740P08000 AA C Screw(4×8)
PCOVP1566FCN1 AV D Upper cabinet rear cover [AR-EF3/EF6]
3
PCOVP1879FCZ1 AR D Upper cabinet rear cover [AR-EF5]
LX-BZ0842FCPZ AH C SPF screw [AR-EF3/EF6]
4
XHBS740P08000 AA C Screw(4×8) [AR-EF5]
GCAB-0942FCN1 AS D Upper cabinet rear [AR-EF3/EF6]
5
GCAB-1081FCZZ AV D Upper cabinet rear [AR-EF5]
LX-BZ0776FCPZ AG C Screw R [AR-EF3/EF6]
6
XHBS740P08000 AA C Screw(4×8) [AR-EF5]
7 GCAB-0945FCNZ AR D Upper cabinet right
DUNT-7133DS14 CR E DSPF unit [AR-EF3]
8
DUNT-7133DS15 CS E DSPF unit [AR-EF6]
9 LFIX-0544FCNZ AH C Glass fixing right
10 CGLSP0003RS52 BF B Table glass EX
11 XBTSC50P16000 AA C Screw(5×16) [AR-EF3/EF6]
12 LFIX-0543FCNZ AH C Glass fixing left [AR-EF3/EF6]
13 CGLSP0102DS51 BF B White datum glass unit [AR-EF3/EF6]
14 XHBS730P06000 AC C Screw(3×6) [AR-EF3/EF6]
15 XBTS740P06000 AA C Screw(4×6)
16 PGIDM1900FCNZ AR C Delivery upper PG SPF [AR-EF3/EF6]
17 PGIDM1901FCNZ AQ D Delivery lower PG [AR-EF3/EF6]
18 NROLP0011QSZZ AD C Delivery support roller [AR-EF3/EF6]
19 PCUSS0383FCZZ AN C Delivery sponge [AR-EF3/EF6]
20 NSFTZ2601FCZZ AH C Delivery support roller shaft 1 [AR-EF3/EF6]
21 MSPRC2865FCZ1 AB C Delivery follower spring [AR-EF3/EF6]
22 XEBS730P08000 AC C Screw(3×8) [AR-EF3/EF6]
23 PCOVP1624FCZZ AC D Stamp cover [AR-EF3/EF6]
24 LX-BZ0465FCWZ AA C Screw(4×6)
25 XHBS730P08000 AB C Screw(3×8)
CPNLC0244DS58 CB E MFP operation panel [AR-EF3]
26
CPNLC0244DS63 CB E MFP operation panel [AR-EF5/EF6]
27 LDAIU0627FCNZ AY D Operation base
28 XEBS740P08000 AA C Screw(4×8)
29 PMLT-1256FCZZ AC C Dustproof cushion 1
30 PMLT-1257FCZZ AB C Dustproof cushion 2
31 RCORF0041FCZZ AH C Ferrite core(UFR25-12-15) [AR-EF3/EF6]
32 PMLT-1402FCZZ AC C Table glass molt A
33 PMLT-1404FCZZ AA C Delivery PG molt A [AR-EF3/EF6]
34 PMLT-1405FCZZ AC C Delivery PG molt B [AR-EF3/EF6]
35 PMLT-1406FCZZ AB C Delivery PG molt C [AR-EF3/EF6]
36 PSHEP5190FCZZ AC C Delivery mylar [AR-EF3/EF6]
37 PSEL-0886FCZZ AC C SPF glass seal [AR-EF3/EF6]
– 31-1 –
manuals4you.com
[ Exteriors[AR-EF3/5/6]
11
29
2
1 2 11
3
7
31 14 2
2 5
6
2
9
30
manuals4you.com
2 10 15
4 32
24
26
15
AR-EF5
12 37
13
2
16 33 34
15 25
23
18 20 34
19 27 28
21 18
17 35
18
19 20
21 19
18
2 36
22 35
36
AR-EF3/6 2
22 FCP09302
– 31-2 –
\ Original detect unit[AR-EF3/5/6]
Inter- PRICE NEW PART Effective
NO. PARTS CODE change RANK MARK RANK DESCRIPTION TR No. time
1 MARMP0148FCZ2 AK C Original detect arm lower
2 XBPS730P06KS0 AB C Screw(3×6KS)
3 LBSHZ1102CCZZ AC C Rubber roller bushing 1
4 PSLDH0178FCZZ AD C Original detect shield plate
5 NSFTZ1805FCPZ AM C Original detect fulcrum shaft
6 XRESP30-06000 AA C E type ring(E3)
7 MSPRT1563FCZZ AC C Original detect spring
8 LHLDZ1085FCZ2 AD C Original detect fulcrum holder
9 CPWBF1453FCE2 AX E ORS emission PWB
10 MARMP0147FCZ2 AK C Original detect arm upper
11 XEPS730P05000 AA C Screw(3×5)
GCAB-0942FCN1 AS D Upper cabinet rear [AR-EF3/EF6]
12
GCAB-1081FCZZ AV D Upper cabinet rear [AR-EF5]
13 XEBS730P08000 AC C Screw(3×8)
501 CARMP0147DS51 BA E ORS emission unit
3
501 2
5
7
10
8
6
12
11
11
13
FCP09303
– 32-1 –
manuals4you.com
] Operation panel unit[AR-EF3/5/6]
Inter- PRICE NEW PART Effective
NO. PARTS CODE change RANK MARK RANK DESCRIPTION TR No. time
CPWBN1560FCE3 BM E LVDS PWB [AR-EF3]
CPWBN1560FCE4 5 BB E LVDS PWB [AR-EF3][Unleaded solder correspondence][With No.8,25] 05/05
1
CPWBN1560FCE3 - BM E LVDS PWB [To No.701][AR-EF3] CCE272 05/12
CPWBN1560FCE4 BB E LVDS PWB [AR-EF5/6]
2 MSPRP3009FCZZ AD C LCD earth plate spring
3 XEPS730P08000 AC C Screw(3×8)
6 DHAI-3903FCZZ AE C ORS PD harness
7 LHLDZ1459FCZZ AE C LCD holder B
VVLLM065HB1-1 CB B LCD module [AR-EF3]
VVLLM065HB1TR 5 BY B LCD module [AR-EF3][Unleaded solder correspondence][With No.1,25] 05/05
8
VVLLM065HB1-1 - CB B LCD module [To No.701][AR-EF3] CCE272 05/12
VVLLM065HB1TR BY B LCD module [AR-EF5/6]
9 LHLDZ1458FCZZ AF C LCD holder A
10 HPNLH0259FCZZ BF D Touch panel
CPWBF1628FCE1 BA E MFP OPE PWB [AR-EF3]
11
CPWBF1646FCE1 BB E MFP OPE PWB [AR-EF5/6]
12 JBTN-0266FCZZ AK C Change key
13 CBTN-0263FC01 AN C Ten key
14 CFILW0284FC03 AF C C key smoke
15 CBTN-0265FC01 AF C C key
16 CFILW0282FC03 AK C Copy key smoke
17 CFILW0283FC03 AH C CA key smoke
18 CBTN-0264FC02 AN C Copy key
19 HPNLC0244FCNZ AY D Operation panel A
20 CPNLC0245FC12 AZ D Operation panel B EX-E
21 LPINS0014QSCZ AF C Fixing pin D
22 DHAI-3193FC11 AC C Panel earth harness
23 LPINS0014QSBZ AF C Fixing pin E
24 PSHEZ4906FCZZ AC C Touch panel sheet
QCNW-0207FCZZ AF C LCD interface FFC [AR-EF3]
LCD interface FFC [AR-EF3]
QCNW-0231FCZZ 5 AG C 05/05
25 [Unleaded solder correspondence][With No.1,8]
QCNW-0207FCZZ - AF C LCD interface FFC [To No.701][AR-EF3] CCE272 05/12
QCNW-0231FCZZ AG C LCD interface FFC [AR-EF5/6]
28 PSHEP5006FCZZ AE C Panel sheet
701 DKIT-0369FCZZ - BZ LCD-INV kit [AR-EF3] CCE272 05/12
– 33-1 –
] Operation panel unit[AR-EF3/5/6]
A 3
3 2
(701) 22
3 1
(701) (701)
3
8 25
3
7
3
10 A
9
6 3 3
3
22
12 3
24 24
13
15 19
11
18
14
28
17
16
21
20
21 23 FCP09304
– 33-2 –
manuals4you.com
Update : 06/02/27
^ Optical unit 1[AR-EF3/5/6]
Inter- PRICE NEW PART Effective
NO. PARTS CODE change RANK MARK RANK DESCRIPTION TR No. time
PCOVP1722FCZ1 AG C Harness cover B [AR-EF3]
1
PCOVP1599FCZ1 AG C Harness cover B [AR-EF5/6]
2 XHBS730P04000 AA C Screw(3×4)
QCNW-0217FCZZ AE C CL interface FFC [AR-EF3]
4
QCNW-0209FCZZ AE C CL interface FFC [AR-EF5/6]
QCNW-0216FCZZ AH C CCD interface FFC [AR-EF3]
CCD interface FFC [Unleaded solder correspondence]
5 QCNW-0232FCZZ 5 AL N C 05/03
[With No.34-18,35-41][AR-EF3]
QCNW-0167FCZZ AM C CCD interface FFC [AR-EF5/6]
PCOVP1761FCZ1 AG C Harness cover C [AR-EF3]
6
PCOVP1600FCZZ AF C Harness cover C [AR-EF5/6]
7 PSHEP4932FCZ1 AC C Harness fixing sheet 4
9 XBBS730P06000 AC C Screw(3×6)
10 LPLTM5723FCZZ AG C Scanner PWB fixing plate
11 XHBS740P08000 AA C Screw(4×8)
12 VHI28F081L40F AY B Scanner flash unit [AR-EF3]
CPWBX1635DS51 BV E Scanner control PWB [AR-EF3]
13 CPWBX1635FCE1 1 BV N E Scanner control PWB [AR-EF3] 06/03 R/C
CPWBN1450FCE2 BW E Scanner control PWB [AR-EF5/6]
14 LHLDW1115FCZZ AD C Edge bushing
15 QCNW-0206FCZZ AH C MFP-OP interface FFC
16 QCNW-0208FCZZ AG C LVDS interface FFC
17 XBBS740P06000 AA C Screw(4×6)
CPWBN1632FCE1 BA E Scanner interface PWB [AR-EF3]
Scanner interface PWB [Unleaded solder correspondence]
18 CPWBN1632FCE2 5 BA N E
[With No.34-5,35-41]
CPWBN1451FCE1 BF E Scanner interface PWB [AR-EF5/6]
19 DHAI-3152FCZZ AF C Stamp interface harness (Japan)
20 LPLTM5720FCZZ AK C OC fixing plate
22 LPLTM5927FCZ1 AF C Dry heater fixing plate
LPLTM6471FCZZ AG C SPF interface harness fixing plate [AR-EF3/6]
24
LPLTM5877FCZZ AE C Base plate reinforce plate [AR-EF5]
25 XHBS730P06000 AC C Screw(3×6)
26 PCOVP1598FCZ1 AL D Harness cover A
27 PSHEZ5337FCZZ AC C Harness fixing sheet 2 [AR-EF3/6]
DHAI-3637FCZZ BP C MFP interface cable [AR-EF3/6]
28
DHAI-3303FCZZ BC C MFP interface cable [AR-EF5]
29 PGUMS0283FCZ1 AA C Table glass cushion
30 LDAIU0610FCZZ AE D Harness fixing base
31 LRALM0183FCZZ AG C MB-B rail F
32 PSHEZ4843FCZ1 AC C Harness fixing sheet 3
34 LHLDW1007LCZZ AD C Mini clamp(MN-1) [AR-EF3]
35 LHLDW0595FCZZ AC C Edge holder(EDS2)
LHLDW0429FCZZ AB C Wire saddle [AR-EF3/6]
36
LHLDW1264FCZZ AD C Wire holder [AR-EF5]
37 LBNDJ0043FCZZ AA C Snap band(SG-130)
38 DHAI-3562FCZZ AD C PNC harness
39 LFIX-0537FCZZ AD C Harness fixing plate
40 PSHEZ4841FCZ2 AC C Harness fixing sheet 1 [AR-EF3]
41 LRALM0184FCZZ AG C MB-B rail R
42 LX-BZ0004QSPZ AB C Screw(RED)
43 PSHEZ0448QSZZ AA C Screw protect sheet
44 LPLTP5960FCZZ AE C Scanner cable fixing plate
45 LHLDW1201CCZZ AA C SK holder
46 LFIX-0569FCZZ AD C Scanner cable fixer
47 PMLT-1282FCZ1 AE C FFC fixing cushion
48 PSHEP5044FCZZ AD C Dust protect mylar
49 XHBS740P06000 AA C Screw(4×6)
50 LFIX-0576FCZZ AF C CCD FCC fixer [AR-EF3]
51 PGSK-0017FCZZ AF C Gasket [AR-EF3]
52 PSHEP5153FCZZ AD C Adhesive sheet 2 [AR-EF3]
53 PSHEP5152FCZZ AE C Adhesive sheet 1 [AR-EF3]
54 PMLT-1429FCZZ AC C Protection cushion [AR-EF3]
55 PSHEZ4842FCZZ AD C Harness fixing sheet 2 [AR-EF5]
– 34-1 –
Update : 06/02/27
^ Optical unit 1[AR-EF3/5/6]
2
1
2
52
45 4 5
17
17 14 11 38
9 2
17
6 2
53
46 44
28 2
11 12 17
10 7 47
37 15
13
25 25
20 19
49 49 16 48 31
37 25
25 25
55
35 18 27 39
35 25 29 17
26
30
50
25 22 51 37
43
20
35 29
29
54
36 25
25 24 41 29
AR-EF3/6 29
40 43
36
32
43
25 43 42
24 25 34
43 25 FCP09305
43
AR-EF5 43
– 34-2 –
manuals4you.com
_ Optical unit 2[AR-EF3/5/6]
Inter- PRICE NEW PART Effective
NO. PARTS CODE change RANK MARK RANK DESCRIPTION TR No. time
! CDAIU0619DS58 BQ E Lamp unit [AR-EF3]
1
! CDAIU0619DS51 BF E Lamp unit [AR-EF5/6]
2 LHLDZ1505FCZZ AC C Wire holder
3 XBBS740P06000 AA C Screw(4×6)
4 LBSHC0161FCZZ AB C Edge saddle [AR-EF5/6]
CCOVP1723FC02 AV D Dark box [AR-EF3]
5
CCOVP1541FC02 AT D Dark box [AR-EF5/6]
6 XHBS730P04000 AA C Screw(3×4)
7 PCUSU0203FCZZ AE C Protection cushion
8 PGIDM1890FCZZ AC C CL guide
9 NPLYZ0399FCZZ AG C W pulley T
10 XBPS740P06KS0 AB C Screw(4×6KS)
12 LFIX-0284FCZZ AC C 2nd,3rd mirror fixing plate F
13 PMIR-0165FCZZ AP B 2nd,3rd mirror
15 MSLI-0138FCZZ AC C Slider
16 PWIR-0201FCZ1 AQ B MB wire F
17 PWIR-0202FCZ1 AQ B MB wire R
18 NBLTH0329FCZZ AG B Winding drive belt
19 LX-BZ0049FCPZ AB C Screw
20 NPLYZ0338FCZZ AN C Pulley(36T)
21 XRESP70-08000 AA C E type ring(E7)
22 LX-BZ0324FCPZ AA C Screw
23 NPLYZ0013QSZZ AL C Winding pulley
24 NPLYZ0005QSZZ AG C Pulley
25 NSFTZ2586FCZZ AS C Winding drive shaft
26 NPLYZ0006QSZZ AD C L pulley
27 RMOTS0914FCZZ BD B Scanner motor
28 XBPS730P05K00 AA C Screw(3×5K)
29 XBPS740P16KS0 AB C Screw(4×16KS)
30 MSPRT2846FCZZ AC C Belt tenshion spring
31 CPLTM5719FC02 AN C Mirror motor fixing plate
32 PGUMS0002QSZZ AL C Protection rubber
33 NGERH0027QSZZ AH C Mirror motor idle gear
34 XRESP70-08000 AA C E type ring(E7)
35 LX-WZ0119FCZZ AA C Washer
36 VHPGP3A38//-1 AH B Photo transistor(GP3A38)
37 XBBS740P14000 AB C Screw(4×14)
38 VHPGP1A22LC-1 AK B Photo interupter(GP1A22LC)
39 XBBS740P10000 AA C Screw(4×10)
40 DHAI-3150FCZZ AD C MHPS interface harness
CPLTM6200DS52 BV E CCD unit [AR-EF3]
41 CPLTM6200DS54 5 BV E CCD unit [AR-EF3][Unleaded solder correspondence][With No.34-5,18] 05/03
CPLTM0031RS51 BS E CCD unit [AR-EF5/6]
42 NBRGC0133FCZ1 AC C PF bearing(M8)
43 XRESP40-05000 AA C E type ring(E4)
44 LHLDZ1381FCZZ AL C ORS PWB holder
45 CPWBF1454FCE2 BN E ORS PD PWB
46 XHBS740P06000 AA C Screw(4×6)
47 XEPS740P06000 AB C Screw(4×6)
48 XHBS730P06000 AC C Screw(3×6)
49 PSHEP5301FCZZ AB C Harness protect sheet
50 LPLTM6574FCZZ AF C Scanner rack fixing plate
51 PMLT-1431FCZZ AC C Protection cushion
52 PSHEP5229FCZZ AE C Dark box protect mylar [AR-EF3]
53 PSHEP5145FCZZ AC C Harness fixing sheet 5 [AR-EF3]
54 PSHEP5230FCZZ AC C Dark box mylar [AR-EF3]
55 PMLT-1399FCZZ AA C SCN molt A
56 PMLT-1400FCZZ AA C SCN molt B
57 PMLT-1401FCZZ AA C SCN molt C
58 PMLT-1403FCZZ AA C Table glass molt B
59 PMLT-1402FCZZ AC C Table glass molt A
60 PSHEP5344FCZZ AB C SCN mylar
61 PSHEP5217FCZZ AD C Stamp mylar 3
62 PSHEZ0448QSZZ AA C Screw protect sheet
63 PSHEP5188FCZZ AC C Operation section mylar 2
64 PSHEP5201FCZZ AD C Step screw mylar
65 PSHEP5189FCZZ AC C Stamp section mylar 1
66 PSHEP5215FCZZ AC C 2nd,3rd mirror unit mylar
501 CHLDZ1446FC31 BC E 2nd,3rd mirror unit
502 CSFTZ2586FC31 AZ E Winder drive shaft unit(Without No.22)
– 35-1 –
_ Optical unit 2[AR-EF3/5/6]
1 3
52
53 6
2
5
6 6
4 54 53
6 6
501 18 19
9
20
21 22
13
23
12 19
10 19
10 9
19 25
51 502
7 17
15 22
12
23
7 19 19
15 16
8
28 21
27 42
41
29 32
29 59
64
39 38
31 32 33
30 62 35 34 63
61 64 48 64
58
60
55
37 60 42
40
65
36 60
21
44 46
47
56
24
26 47
43 26 62 47
24 50 66 46 45
55 49
48 48 57
FCP09306
– 35-2 –
manuals4you.com
. Lamp unit[AR-EF3/5/6]
Inter- PRICE NEW PART Effective
NO. PARTS CODE change RANK MARK RANK DESCRIPTION TR No. time
! RLMPD0702FCZZ BB B Lamp [AR-EF3]
1
! RLMPD0658FCZ1 BA B Lamp [AR-EF5/6]
2 XEBS730P08000 AC C Screw(3×8)
3 PREFL0172FCZZ AK B Reflector
4 XBBS730P12000 AA C Screw(3×12)
5 LDAIU0619FCZ1 AS D Lamp base
6 PCUSU0203FCZZ AE C Protection cushion
QCNW-0217FCZZ AE C CL interface FFC [AR-EF3]
7
QCNW-0209FCZZ AE C CL interface FFC [AR-EF5/6]
8 MSLI-0138FCZZ AC C Slider
9 CPWBF1449FC31 BH E Inverter PWB
10 PCUSF0334FCZZ AP C Mirror cushion
11 LSTYM0261FCZZ AB C Wire support plate
12 LFIX-0545FCZZ AC C CL read harness fixer
13 CMIR-0164FC01 AP B 1st mirror
14 MSPRP2825FCZZ AC C Mirror spring
15 TLABZ4335FCZZ AB D HV caution label
(Unit)
CDAIU0619DS58 BQ E Lamp unit [AR-EF3]
901
CDAIU0619DS51 BF E Lamp unit [AR-EF5/6]
. Lamp unit[AR-EF3/5/6]
1
15
6 2
4
8
14 10
5
11
2 8
9 6
12
8
13
11
14
2
FCP09307
– 36-1 –
Update : 06/02/27
a DSPF Assembly section[AR-EF3/6]
Inter- PRICE NEW PART Effective
NO. PARTS CODE change RANK MARK RANK DESCRIPTION TR No. time
1 PSHEZ4845FCZ1 AV C OC mat
2 PMLT-1286FCZZ AD C OC cushion
3 PCOVP1595FCZZ AG D Rack cover
4 XHBS730P06000 AC C Screw(3×6)
5 PCOVP1615FCZZ AE D Length detect cover N
6 XEBS740P10000 AA C Screw(4×10)
MHNG-0208FCZZ BA C SPF hinge R
7
MHNG-0208FCPZ 3 BA N C SPF hinge R [Unleaded correspondence] 06/02
9 PCOVP1518FCZZ AE D ICU ROM cover
10 LPLTM5887FCZZ AL C Hinge joint plate
11 XHBS740P08000 AA C Screw(4×8)
12 LFIX-0568FCZZ AC C Original detect fixer
13 PTPE-0265FCZZ AC C Cover tape
14 PCOVP1644FCZZ AD D F cover L
15 PGUMS0298FCZ1 AC C Cover rubber L
16 CPWBF1594FCE1 AR E SPF VR PWB
17 LPLTP5743FCZZ AF C Width detect fixing plate
18 XEBS730P08000 AC C Screw(3×8)
19 MSPRP2830FCZZ AA C Width detect spring
20 PGUMS0296FCZZ AD C Cushion
21 NGERR1386FCZZ AE C Width detect rack
22 NGERP1385FCZZ AF C Width detect pinion
23 XEPS730P06X00 AA C Screw(3×6X)
24 PCOVP1645FCZ1 AH D F cover R
25 PGUMS0299FCZ1 AH C Cover rubber R
26 CPWBF1459FCE3 AY E SPF PWB
DHAI-3902FCZZ BA C DSPF body interface harness [AR-EF3]
27
DHAI-3679FCZZ BB C DSPF body interface harness [AR-EF6]
28 XESS730P08000 AB C Screw(3×8)
29 DHAI-3161FCZZ AK C SPF size detect harness
30 XEBS730P10000 AC C Screw(3×10)
33 VHPGP1A73A+-1 AG B Photo sensor(GP1A73A)
34 MLEVP0794FCZZ AC C Length detect actuator
35 XEBS740P16000 AB C Screw(4×16)
37 LPLTP6467FCZZ AF C Adjust plate R
38 LPLTP6466FCZZ AF C Adjust plate F
39 PCOVP1549FCNZ AW D Upper cover
40 XEBS730P08000 AC C Screw(3×8)
41 MARMP0243FCZZ AD C Manual feeding tray arm
42 PRNGP0090FCZZ AA C Ring(E5)
43 LPLTM2573FCZ1 AD C ADF MG plate
44 LPLTP5938FCZZ AC C Shading plate N
45 TLABH4847FCZZ AD D Original read label
46 PMLT-1293FCZZ AC C Protection cushion
47 PCOVP1686FCZZ AH D Base tray cover
48 LBNDJ0013FCZ1 AE C Cable band
49 GCAB-0944FCN2 BF D Base tray
– 37-1 –
manuals4you.com
Update : 06/02/27
a DSPF Assembly section[AR-EF3/6]
6 3
6 6
11
11
5
11
6
9
7 6 12 11
6
6
48
6 18
16 18
12
46
27 18 20
30
10 43 23
18
17
44 21
29
40 28 19
30 18
26
30 22
33 30 23
11 11
35 21 15
33
49
4
34 14
13
25 4 29
41
18
37
38
24 42
6
40
47 39 45
FCP09308 6
6
.com
manuals4you
– 37-2 –
Update : 06/02/27
b DSPF Paper feed unit[AR-EF3/6]
Inter- PRICE NEW PART Effective
NO. PARTS CODE change RANK MARK RANK DESCRIPTION TR No. time
1 PCOVP1594FCZZ AG D Roller cover
2 XHBS730P06000 AC C Screw(3×6)
3 PMLT-1272FCZZ AB C Damper cushion 3
4 PGIDM2093FCZZ AN C Paper feed PG SPF
5 PSHEP5328FCZZ AD C PS rear mylar
6 NROLM1499FCZZ AT C Delivery roller M
7 NSFTZ2600FCZZ AM C PS support shaft
8 MSPRP3108FCZZ AC C PS support plate spring
9 XEBS730P08000 AC C Screw(3×8)
10 NSFTZ2599FCZ1 AW C Separate roller shaft SPF
11 XRESP40-06000 AA C E type ring(E4)
12 NBRGC0136FCZ1 AC C Bearing(M6)
13 LHLDZ1483FCZZ AF C Paper feed rotation plate
14 PCLC-0303FCZZ AT B Separate clutch
15 NSFTZ2678FCZZ AL C Pick up shaft
16 NPLYZ0398FCZZ AC C Pick up roller pulley(22P)
17 NBRGM0096FCZ1 AC C Bearing
18 NBLTH0363FCZZ AG B Belt(S2M120)
19 NROLR1312FCZZ AN A Pick up roller
20 NPLYZ0397FCZZ AK C Paper feed roller pulley(28P)
21 NROLR1317FCZZ AP C Separate roller
22 PCLC-0302FCZZ AT B PS clutch SPF
23 LPLTM5928FCZZ AG C Paper feed base plate SPF
24 XBBS730P06000 AC C Screw(3×6)
25 RPLU-0336FCZZ AS B Pick up solenoid
26 MARMP0284FCZZ AC C Pick up joint arm N
27 XRESP50-06000 AA C E type ring(E5)
29 XRESP70-08000 AA C E type ring(E7)
30 NROLR1483FCZZ AS C PS roller SPF
31 LSTYM0288FCZZ AK C CIS stay
32 LHLDZ1485FCZZ AC C SP holder F
33 MSPRD3002FCZZ AC C Spring N
MHNG-0209FCZ1 BB C DSPF hinge L
34
MHNG-0209FCP1 3 BB N C DSPF hinge L [Unleaded correspondence] 06/02
35 RMOTS0915FCZZ BF B SPF motor N
36 LFRM-1022FCZZ AK C Drive frame
37 NGERH1477FCZZ AC C Gear(24T)
38 PSHEZ4949FCZZ AE C Motor sheet
39 MSPRP3011FCZZ AC C Earth plate spring
40 LHLDW1009ACZZ AA C Clamp
41 XHBS740P08000 AA C Screw(4×8)
42 NGERH1476FCZZ AD C Gear(35T/18T)
43 NGERH1478FCZZ AE C Gear(55T/28T/18P)
44 NBLTH0364FCZZ AG B Belt(S2M130)
45 LHLDZ1486FCZZ AC C SP holder R
46 NPLYZ0375FCZZ AC C Pulley(22T)
47 CPLTM5882FC02 AN C Drive plate
48 LPINS1031HCZZ AA C Spring pin
49 PCLR-0426FCZZ AD C Slide collar
50 NROLR1320FCZZ AQ C Delivery roller SPF
51 LPLTM5884FCZ1 AW C Base tray reinforce plate N
52 PCOVP1818FCZZ AC D DSPF interface harness cover
53 LPLTM5785FCZZ AC C MG plate
54 XRESP20-04000 AA C E type ring(E2)
55 PMLT-1270FCZZ AB C Damper cushion 1
56 JKNBZ0141FCZZ AH C Jam release knob
57 LPLTM5889FCZZ AC C Datum plate
58 PSHEP4846FCZZ AD C OC mat mylar R
59 LHLDW2101SCZZ AB C Cable clamp
61 LPLTM5929FCZZ AR C Delivery roller fixing plate
62 DHAI-3281FCZZ AH C SPF delivery sensor harness
63 QSW-Z0544FCZZ AY B Delivery jam sensor
64 PCUSS0372FCZ1 AD C CIS cushion 1
65 XEBS740P10000 AA C Screw(4×10)
67 LHLDZ1484FCZZ AC C Open/close holder
68 VHPGP1A73A+-1 AG B Photo sensor(GP1A73A)
69 MSPRC3001FCZZ AB C Open/close detect spring N
70 MLEVP0837FCZZ AC C Open/close actuator N
71 XHBS730P10000 AD C Screw(3×10)
72 PCUSS0373FCZ1 AB C CIS cushion 2
73 PSHEP5319FCZZ AF C White mylar
74 PGIDH1897FCZZ AT C CIS paper guide
75 PGLSP0103FCZZ AV C CIS glass
76 LX-BZ0931FCZZ AC C Screw(M3)
77 PBRSS0209FCZZ AG B Discharger brush SPF
78 LHLDW1426FCZZ AC C Mini clamp
80 MSPRC3269FCZZ AC C Follower shaft earth spring
81 XWHS730-05080 AA C Washer
82 PGIDM2110FCZZ AC C PS guide
– 38-1 –
manuals4you.com
Update : 06/02/27
b DSPF Paper feed unit[AR-EF3/6]
2 1 3
2
5 2
6
8 81
9 80
9
7
8
10
A 27 9
B 11
14 13
34 11
27 17 12 15
11 16
23 C 18
22 12 19
38 29 24 26
27
manuals4you.com
78 17 17
27
24 82 20
36 2 31
21
35 A 24 25
B 27 37 2
42 30
40 45
24 33
24 2
54 29
43 37
27 33
59 51 2
49 41
32 82
44 47
46 52
48 17
C
50 55
65 2
2 58
61 62
39 58
40 57 2
2 53
63 2 2
17 2 72 17
77 56
39
41 2
41 27 57 2 27
77
62 64
68 67 72
71 69 76 73
70 41
75 74
FCP09309
76
– 38-2 –
Update : 06/02/27
c DSPF Upper transfer unit[AR-EF3/6]
Inter- PRICE NEW PART Effective
NO. PARTS CODE change RANK MARK RANK DESCRIPTION TR No. time
1 LPLTM5891FCZ1 AE C Upper delivery rainforce plate
2 PMLT-1272FCZZ AB C Damper cushion 3
3 LSTPP0353FCZZ AE C Original stopper
5 LPLTM6472FCZZ AD C Separate pad rainforce plate
6 XEBS730P08000 AC C Screw(3×8)
CPLTM5746FC01 AE C Separate pad fixing plate
7
CPLTM5746FC01 - AE C Separate pad fixing plate ARE805 05/11
LPLTM6477FCZZ AC C Separate plate
8
LPLTM6477FCZZ - AC C Separate plate ARE805 05/11
10 VHPGP1A73A+-1 AG B Photo sensor(GP1A73A)
11 PMAGT0072FCPZ AF C Magnet catch
12 RPLU-0347FCZ1 AQ B Gate solenoid
13 DHAI-3162FCZZ AK C SPF paper feed harness
14 MLEVP0796FCZZ AC C Set detect actuator
15 MARMP0248FCZZ AE C MF gate joint arm
16 MLEVP0804FCZZ AC C Stopper lever
LPLTM6456FCZZ AC C Front separate plate
17
LPLTM6456FCZZ - AC C Front separate plate ARE805 05/11
PSHEZ5338FCZZ AH C Separate sheet
19
PSHEZ5338FCZZ - AH C Separate sheet ARE805 05/11
PSHEP5340FCZ1 AF C Separate mylar lower
20
PSHEP5340FCZ1 - AF C Separate mylar lower ARE805 05/11
21 LSTPP0314FCZZ AA C E3 stopper
22 MSPRD2870FCZ1 AC C Stopper spring
23 NSFTZ2659FCZZ AR C Fulcrum shaft
24 LPLTM5932FCZZ AC C Tray 2 sensor fixing plate
25 XEBS740P10000 AA C Screw(4×10)
26 MLEVP0797FCZZ AC C PS front actuator
27 MSPRD2879FCZZ AB C PS front actuator spring
28 PMLT-1271FCZZ AB C Damper cushion 2
29 PSHEP4937FCZZ AB C Fixing mylar
30 PGIDM1899FCN1 AY C Upper transport PG
31 MSPRT2863FCZZ AB C Paper feed plate spring
32 LPLTP5748FCZZ AD C Paper feed plate
XHBS730P06000 AC C Screw(3×6)
34
XHBS730P06000 - AC C Screw(3×6) ARE805 05/11
35 LX-BZ0064QSZZ AA C Screw(3×8)
36 PSHEP5320FCZZ AC C PS front mylar A
37 PSHEP5321FCZZ AC C PS front mylar B
38 PSHEP5322FCZZ AC C PS front mylar C
39 PSHEP5323FCZZ AC C PS front mylar D
701 MSPRT2864FCZZ - AC C Pressure spring ARE805 05/11
702 XHBS730P06000 - AC C Screw(3×6) ARE805 05/11
703 MSPRP2832FCZZ - AC C Separate assistance plate spring ARE805 05/11
704 LPLTP7040FCZZ - AC C Plate ARE805 05/11
705 LPLTM7039FCZZ - AD N C Plate ARE805 05/11
706 PSHEZ4847FCZZ - AL C Separate sheet ARE805 05/11
707 PSHEP4848FCZZ - AB N C Sheet ARE805 05/11
708 LPLTP5747FCZZ - AC C Separate plate ARE805 05/11
709 CPLTM5746FC01 - AE C Separate pad fixing plate ARE805 05/11
710 CPLTM5746DS51 - AT E Separate pad fixing plate AS ARE805 05/11
– 39-1 –
manuals4you.com
Update : 06/02/27
c DSPF Upper transfer unit[AR-EF3/6]
6 34
A
6 3
6
10 1
6
2
34
11 8
6
5
13 14 7
10
19
20
25 12 17
35 710
701
15 16
24
28 708 709
21 703
704
22 702 705
A 26 706
27
28
10 707
34 23
6
11
30
29 31
32
37
39 36
FCP09310 38
– 39-2 –
d DSPF CIS unit[AR-EF3/6]
Inter- PRICE NEW PART Effective
NO. PARTS CODE change RANK MARK RANK DESCRIPTION TR No. time
CPWBN1567FCE3 BN E CIS control PWB [AR-EF3]
1
CPWBN1458FCE3 BT E CIS control PWB [AR-EF6]
2 XBBS730P06000 AC C Screw(3×6)
PCOVP1813FCZZ AG D CIS PWB cover N [AR-EF3]
3
PCOVP1593FCZ1 AF D CIS PWB cover N [AR-EF6]
4 DUNT-7079FC14 CB E CIS unit
5 LX-BZ0680FCZZ AB C Screw
6 QCNW-0170FCZZ AH C CIS interface FFC
7 XBBS740P08000 AA C Screw(4×8)
8 PMLT-1284FCZZ AE C Interface FFC fixing cushion
9 DHAI-3663FC11 AK C CIS FG harness
2
3
2
2
2 2
7 8
2
6
7
9
5
2
5 FCP09311
– 40-1 –
manuals4you.com
e OC cover unit[AR-EF5]
Inter- PRICE NEW PART Effective
NO. PARTS CODE change RANK MARK RANK DESCRIPTION TR No. time
4 MHNG-0218FCZZ AD C OC cover hinge
5 LPINS0346FCZZ AE C OC cover hinge pin
6 XJBS740P08000 AB C Screw(4×8)
7 MHNG-0223FCZZ AT C OC hinge L
8 XJBS740P10000 AB C Screw(4×10)
9 MHNG-0224FCZZ AT C OC hinge R
10 PSHEZ5357FCZ1 AW C OC cushion
(Unit)
901 DUNT-7440DSZZ BR E OC cover unit(Except No.10)
e OC cover unit[AR-EF5]
4
5
6
4
8 7
6 5
4
8 9
10 6 901
FCP09312
– 41-1 –
f Packing Material & Accessories[AR-EF3/5/6]
Inter- PRICE NEW PART Effective
NO. PARTS CODE change RANK MARK RANK DESCRIPTION TR No. time
1 SPAKA6075DSZZ AA D RSPF protect sheet 1
LSOU-0177FCG5 AP D Delivery tray T
2
LSOU-0179FCZ5 AR D Delivery tray 1
4 TCADZ1178FCZZ AB D Screw caution card
5 LX-BZ0787FCPZ AD C Screw for 2/3 mirror lock
6 SPAKA6697FCZZ BR D Top add [AR-EF3/4/6]
7 SSAKZ0003QSZZ AF D Body vinyl bag
8 SPAKA6523FCZZ BN D Bottom add [AR-EF3/4/6]
SPAKC6696FCZZ BU D Packing case [AR-EF3]
9 SPAKC6732DS11 BS D Packing case [AR-EF5]
SPAKC6696DS15 BS D Packing case [AR-EF6]
10 SPAKA6265FCZZ AC D Fusing protect add
11 SSAKA1130QCZZ AA D Vinyl bag(100×120)
12 LX-BZ1000FCZZ AF C Screw
13 LX-BZ1001FCZZ AD C Screw
14 XBPSE40P08KS0 AA C Screw(4×8KS) [AR-EF3]
15 PSHEP5354FCZZ AC C Scanner rack sheet D
100 TLABH4847FCZZ AD D Original read label [AR-EF6]
12 13 14
15
1 7
11
10
8
2
5 9
4
FCP09313
– 42-1 –
manuals4you.com
g Packing Material & Accessories[AR-RK2]
Inter- PRICE NEW PART Effective
NO. PARTS CODE change RANK MARK RANK DESCRIPTION TR No. time
1 LPLTM6454FCZZ BA C Rack bottom plate
PCOVP1810FCZZ AE C Rack cover right
2
PCOVP1811FCZZ AE C Rack cover left
3 PSHEP5351FCZZ AE C Scanner rack sheet L
4 LX-BZ1014FCZZ AD C Screw
5 JHNDM0176FCZ1 AQ C Left rack rear handle
6 LX-BZ0888FCZZ AC C Screw
7 CCHSM0111FC02 BM C Left rack upper
8 CCHSM0110FC02 BL C Right rack upper
9 PSHEP5353FCZZ AB C Scanner rack sheet F
11 PSHEP5352FCZZ AE C Scanner rack sheet R
12 XBPSE30P12KS0 AA C Screw(3×12KS)
13 JHNDP0160FCZZ AD C Adjust knob
14 NSFTZ2887FCZZ AP C Adjust shaft
15 MCAMP0105FCZZ AC C Adjust cam
16 LX-BZ0903FCZ1 AC C Screw(5×70)
17 XHBSE40P08000 AA C Screw(4×8)
18 XBPS740P08KS0 AB C Screw(4×8KS)
101 XBBSE30P06000 AA C Screw(3×6)
103 CPLTM6627FC01 AD C Rack adjust plate
5
11
4 63
2 6
3
7
8
9 16 17 18
12
14 13 3
15
FCP09314
– 43-1 –
Update : 06/02/27
h Scanner control PWB[AR-EF3]
Inter- PRICE NEW PART Effective
NO. PARTS CODE change RANK MARK RANK DESCRIPTION TR No. time
1 RFILN0047FCZZ AC C Filter(MMZ1608S121AT) [NF6,NF5]
2 RFILN0062FCPZ AC C Line Filter(ZJSR5101-102TA-01) [NF1,NF3]
3 RFILN0063FCPZ AD C Line Filter(ZJSR5101-103TA-01) [NF4,NF2]
RMPTR4103ACZZ AB B Block resistor(10KΩ×4) [BR2,BR3,BR4,BR5,BR6]
RMPTR4103ACZZ AB B Block resistor(10KΩ×4) [BR7,BR8,BR9,BR10,BR12]
4 RMPTR4103ACZZ AB B Block resistor(10KΩ×4) [BR13,BR14,BR16,BR18,BR20]
RMPTR4103ACZZ AB B Block resistor(10KΩ×4) [BR22,BR23,BR24,BR25,BR26]
RMPTR4103ACZZ AB B Block resistor(10KΩ×4) [BR27,BR28,BR29,BR30,BR31,BR37]
RMPTR4330ACZZ AB B Block resistor(33Ω×4) [BR1,BR11,BR15,BR17,BR19]
5
RMPTR4330ACZZ AB B Block resistor(33Ω×4) [BR21,BR32,BR33,BR34,BR35,BR36]
6 VCCCCZ1HH100D AA C Capacitor(50WV 10pF) [C55,C56]
VCKYCZ1HB102K AA C Capacitor(50WV 1000pF) [C15,C16,C21,C25,C26]
VCKYCZ1HB102K AA C Capacitor(50WV 1000pF) [C27,C28,C32,C33,C34]
7
VCKYCZ1HB102K AA C Capacitor(50WV 1000pF) [C35,C36,C37,C44,C45]
VCKYCZ1HB102K AA C Capacitor(50WV 1000pF) [C46,C47,C49,C50,C82,C88]
8 VCKYCZ1HB222K AA C Capacitor(50WV 2200pF) [C57,C58,C65,C66]
9 VCKYCZ1CB103K AA C Capacitor(16WV 0.01µF) [C39,C80,C81,C83,C84]
10 VCKYCZ1HF103Z AA C Capacitor(50WV 0.01µF) [C3,C17,C18]
VCKYCZ1EF223Z AA C Capacitor(25WV 0.022µF) [C1,C4,C5,C13,C14]
VCKYCZ1EF223Z AA C Capacitor(25WV 0.022µF) [C20,C22,C29,C30,C38]
VCKYCZ1EF223Z AA C Capacitor(25WV 0.022µF) [C40,C42,C43,C48,C53]
11 VCKYCZ1EF223Z AA C Capacitor(25WV 0.022µF) [C54,C59,C60,C61,C68]
VCKYCZ1EF223Z AA C Capacitor(25WV 0.022µF) [C69,C71,C73,C74,C75]
VCKYCZ1EF223Z AA C Capacitor(25WV 0.022µF) [C76,C77,C78,C85,C86]
VCKYCZ1EF223Z AA C Capacitor(25WV 0.022µF) [C87,C90]
VRS-CZ1JD000J AA C Resistor(1/16W 0Ω ±5%) [R34,R35,R36,R42,R43]
12
VRS-CZ1JD000J AA C Resistor(1/16W 0Ω ±5%) [R44,R53]
13 VRS-CZ1JD330J AA C Resistor(1/16W 33Ω ±5%) [R12]
15 VRS-CZ1JD151J AA C Resistor(1/16W 150Ω ±5%) [R24]
16 VRS-CZ1JD331J AA C Resistor(1/16W 330Ω ±5%) [R5,R9,R91]
17 VRS-CZ1JD561F AA C Resistor(1/16W 560Ω ±1%) [R60]
18 VRS-CZ1JD621F AA C Resistor(1/16W 620Ω ±1%) [R61]
19 VRS-CZ1JD681J AA C Resistor(1/16W 680Ω ±5%) [R67]
20 VRS-CZ1JD911F AA C Resistor(1/16W 910Ω ±1%) [R58]
21 VRS-CZ1JD102J AA C Resistor(1/16W 1KΩ ±5%) [R10,R18,R39,R40,R57,R93]
22 VRS-CZ1JD122J AA C Resistor(1/16W 1.2KΩ ±5%) [R87,R88]
23 VRS-CZ1JD562J AA C Resistor(1/16W 5.6KΩ ±5%) [R68,R70,R72]
24 VRS-CZ1JD752J AA C Resistor(1/16W 7.5KΩ ±5%) [R25,R51,R52]
VRS-CZ1JD103J AA C Resistor(1/16W 10KΩ ±5%) [R1,R4,R6,R7,R8]
VRS-CZ1JD103J AA C Resistor(1/16W 10KΩ ±5%) [R13,R17,R20,R21,R22]
VRS-CZ1JD103J AA C Resistor(1/16W 10KΩ ±5%) [R23,R26,R27,R28,R30]
25 VRS-CZ1JD103J AA C Resistor(1/16W 10KΩ ±5%) [R33,R45,R46,R47,R48]
VRS-CZ1JD103J AA C Resistor(1/16W 10KΩ ±5%) [R49,R50,R55,R56,R62]
VRS-CZ1JD103J AA C Resistor(1/16W 10KΩ ±5%) [R63,R64,R65,R66,R69]
VRS-CZ1JD103J AA C Resistor(1/16W 10KΩ ±5%) [R71,R73,R78,R90,R92]
26 VRS-CZ1JD103F AA C Resistor(1/16W 10KΩ ±1%) [R79,R89]
27 VRS-CZ1JD203J AA C Resistor(1/16W 20KΩ ±5%) [R14]
28 VRS-CZ1JD303J AA C Resistor(1/16W 30KΩ ±5%) [R94]
29 VRS-CZ1JD303F AA C Resistor(1/16W 30KΩ ±1%) [R80]
30 VRS-CZ1JD624J AA C Resistor(1/16W 620KΩ ±5%) [R31]
31 VRS-CZ1JD105J AA C Resistor(1/16W 1MΩ ±5%) [R41]
32 VRS-TP2BD131J AA C Resistor(1/8W 130Ω ±5%) [R82,R84]
33 VRS-TP2BD151J AA C Resistor(1/8W 150Ω ±5%) [R81,R83]
34 VRS-TP2BD301J AA C Resistor(1/8W 300Ω ±5%) [R85]
35 VRS-TP2BD471J AA C Resistor(1/8W 470Ω ±5%) [R74,R75,R76]
36 VRS-TP2BD561J AA C Resistor(1/8W 560Ω ±5%) [R77]
37 VRS-TP2BD152J AA C Resistor(1/8W 1.5KΩ ±5%) [R86]
VHDCRH01+++-1 AC B Diode(CRH01) [D15,D16,D17,D18,D19]
38
VHDCRH01+++-1 AC B Diode(CRH01) [D20,D21,D40]
39 VHDMA704A//-1 AC B Diode(MA704A) [D28]
40 VHDRLS73///-1 AA B Diode(RLS-73) [D22,D23,D25,D26,D27]
41 VHDDA204U//-1 AB B Diode(DA204U) [D24]
VHDDAN202U/-1 AB B Diode(DAN202U) [D31,D33,D34,D35,D36]
42
VHDDAN202U/-1 AB B Diode(DAN202U) [D37,D42,D2,D10]
43 VHDDAP202U/-1 AB B Diode(DAP202U) [D29,D30,D32,D38,D39,D41]
45 VSDTA143ZUA-1 AB B Transistor(DTA143ZUA) [Q10,Q11,Q12]
46 VSDTC143ZUA-1 AC B Transistor(DTC143ZUA) [Q2,Q3,Q7,Q8,Q9]
48 VS2SK3018++-1 AC B Transistor(2SK3018) [Q1]
49 VS2SK3065++-1 AG B Transistor(2SK3065) [Q13,Q14]
50 VS2SB1197KR-1 AC B Transistor(2SB1197K) [Q4,Q5,Q6]
57 QCNCW1190FCPZ AN C Connector(TX24-100R-LT-H1) [CN1]
58 QCNCM7022SC0E AB C Connector(S5B-PH-K-S) [CN2]
59 QCNCM1187FCZZ AM C Connector(BM30B-SRDS-G-TFC) [CN3]
60 QCNCM1167FCZZ AP C Connector(BM50B-SRDS-G-TFC) [CN4]
61 QCNCM7022SC0F AB C Connector(S6B-PH-K-S) [CN6]
62 QCNCM0828FCZZ AE C Connector(S26B-PHDSS) [CN7]
63 QCNCW0948FC12 AG C Connector(1-171825-2) [CN8]
64 QCNCM7014SC1C AC C Connector(B13B-PH-K-S) [CN9]
– 44-1 –
manuals4you.com
Update : 06/02/27
h Scanner control PWB[AR-EF3]
Inter- PRICE NEW PART Effective
NO. PARTS CODE change RANK MARK RANK DESCRIPTION TR No. time
65 QCNCM0829FCZZ AG C Connector(S28B-PHDSS) [CN10]
66 QCNCM7022SC0C AB C Connector(S3B-PH-K-S) [CN11]
67 VHPLT1D67A/-1 AC B LED(RED)(LT1D67A) [LED1]
68 RCRSZ0001QSZZ AG B Crystal(19.6608MHz) [X1]
69 RCRMZ6007RCZZ AD B Crystal(4.19MHz) [X2]
70 VRS-RE3DA1R0J AB C Resistor(2W 1.0Ω ±5%) [R16,R19]
71 QSOCZ0095FCZZ AR C IC Socket(179707-1) [SOCKET1]
72 QSOCZ0002QSPZ AC C IC Socket(8Pin) [IC23]
73 VHIC24WC08L-1 AF B IC(C24WC08L) [IC23]
75 RH-IX0037QSPZ AQ B SRAM(IS61LV256-15JL) [IC11]
76 VHIHN58V65A-1 AW B P-EEPROM(HN58V65AP) [IC20]
78 VHIVHC244SJ-1 AG B IC(74VHC244SJ) [IC7,IC8]
79 VHI74VHCT244X AF B IC(74VHCT244ASJX) [IC10]
80 VHI74VHC04M-1 AE B IC(74VHC04M) [IC3,IC21]
81 VHI74VHC32M-1 AD B IC(74VHC32M) [IC6]
82 VHI74VHCT08AJ AD B IC(74VHCT08ASJ) [IC2]
83 VHILM324D++-1 AE B IC(LM324D) [IC19]
84 VHILM339D++-1 AE B IC(LM339D) [IC9]
85 VHITD62003AP1 AG B IC(TD620003AP1) [IC4,IC5,IC18]
86 VHID62503FG-1 AG B IC(D62503FG) [IC1,IC17]
87 VHIMTD1361F-1 AR B Driver IC(MTD1361F) [IC12]
88 VHIL108733N-1 AG B IC(L1087MPX-3.3/NOPB) [IC14]
(Unit)
CPWBX1635DS51 BV E Scanner control PWB
901
CPWBX1635FCE1 1 BV N E Scanner control PWB 06/03 R/C
– 44-2 –
i Scanner interface PWB[AR-EF3]
Inter- PRICE NEW PART Effective
NO. PARTS CODE change RANK MARK RANK DESCRIPTION TR No. time
QCNCW1001YC40 AH C Connector(IL-FPR-40S-VF-E1500) [CN1]
1 Connector(IL-FPR-40S-VF-E1500) [Unleaded solder correspondence]
QCNCW1358FCPZ 5 AR N C 05/03
[With CPWBN1632FCE2][CN1]
2 QCNCW1212FCPZ AE C Connector(SLD5S-1) [CN2]
3 QCNCW1186FCZZ AF C Connector(TX25-100P-LT-H1) [CN3]
4 QCNCW1134FCZZ AH C Connector(T24FAZ-SMT-TF) [CN4]
5 QCNCM0991FCZZ AG C Connector(30FMZ-BT) [CN5]
6 QCNCM7014SC0D AB C Connector(B4B-PH-K-S) [CN6]
8 VHDRLS73///-1 AA B Diode(RLS-73) [D1]
9 VCKYCZ1HF103Z AA C Capacitor(50WV 0.01µF) [C1,C3]
10 VCEASX1CN476M AC C Capacitor(16WV 47µF) [C2]
12 VRS-CZ1JD000J AA C Resistor(1/16W 0Ω ±5%) [R1,R2]
(Unit)
CPWBN1632FCE1 BA E Scanner interface PWB
901 Scannaer interface PWB [Unleaded solder correspondence]
CPWBN1632FCE2 5 BA N E 05/03
[With No.34-5,35-41]
– 45-1 –
manuals4you.com
j MFP OPE PWB[AR-EF3]
Inter- PRICE NEW PART Effective
NO. PARTS CODE change RANK MARK RANK DESCRIPTION TR No. time
QSW-P0008QSZZ AC B Push switch(EVQ23G04K) [0K,1K,2K,3K,4K]
QSW-P0008QSZZ AC B Push switch(EVQ23G04K) [5K,6K,7K,8K,9K]
2
QSW-P0008QSZZ AC B Push switch(EVQ23G04K) [*K,#K,CAK,CLK,PRK]
QSW-P0008QSZZ AC B Push switch(EVQ23G04K) [FAK,COK,JOK,CUK]
3 QSW-P0469FCZZ AD B Push switch(B3W-1100) [PSW]
4 QCNCW1134FCZZ AH C Connector(T24FAZ-SMT-TF) [CN101]
5 QCNCM1171FCZZ AE C Connector(B6B-PH-SM3-TB) [CN102]
6 RALMB1002LCZZ AE B Alarm(PKM13EPY-4000-TF01) [BZ1]
7 RCRS-0007FCZZ AD B Crystal(CSBLA480EC8B-B0) [X1]
8 VCEAJU1CW476M AB C Capacitor(16WV 47µF) [C1,C4]
9 VCKYPU1HB101K AA C Capacitor(50VW 100pF) [C6,C7]
10 VCKYPU1EB223Z AB C Capacitor(50VW 0.022µF) [C2,C3,C5]
11 VHIM34282M1-1 AG B IC(M34282M1-F57GP[KEYCF57]) [IC101]
VHPSLR322MC3F AC B LED(GREEN)(SLR-322MC) [PRT,FAX,COPY,JOB,PONL]
12
VHPSLR322MC3F AC B LED(GREEN)(SLR-322MC) [ICPDATA,FCOM,FDATA]
13 VRD-HT2EY102J AA C Resistor(1/4W 1.0kΩ ±5%) [R1]
14 VRD-HT2EY221J AA C Resistor(1/4W 220Ω ±5%) [R2]
16 VSDTC114YS/-1 AB B Transistor(DTC114YSA) [Q1]
17 VHPLT9400E/-1 AK B LED(LT9400E) [RPL]
(Unit)
901 CPWBF1628FCE1 BA E MFP OPE PWB
– 46-1 –
k CIS control PWB[AR-EF3]
Inter- PRICE NEW PART Effective
NO. PARTS CODE change RANK MARK RANK DESCRIPTION TR No. time
1 VHIVHC244SJ-1 AG B IC(74VHC244SJ) [IC3]
2 VHI87R1150E-1 BF B IC(208pin_ASIC) [IC5]
3 VHI74VHC04M-1 AE B IC(74VHC04M) [IC7]
4 VHI7SZ125M5-1 AE B IC(NC7SZ125M5X) [IC4]
5 VHIVHC240SJ-1 AF B Driver IC(74VHC240SJ) [IC1]
7 VHIF1117S25-1 AF B IC(F1117S25) [IC6]
8 VHDD1FM3706-1 AD B Diode(D1FM3706) [D1]
VCCCCZ1HH101J AA C Capacitor(50WV 100pF) [C11,13,14,15,16,27]
13
VCCCCZ1HH101J AA C Capacitor(50WV 100pF) [C46∼55,69∼71]
VCKYCZ1HB102K AA C Capacitor(50WV 1000pF) [C6,12,23,25]
14
VCKYCZ1HB102K AA C Capacitor(50WV 1000pF) [C35,37,39]
VCKYCZ1HF103Z AA C Capacitor(50WV 0.01µF) [C17,22,24,34]
15
VCKYCZ1HF103Z AA C Capacitor(50WV 0.01µF) [C36,38,60,62]
VCKYCZ1CF104Z AB C Capacitor(16WV 0.10µF) [C1∼5,10,18∼21]
VCKYCZ1CF104Z AB C Capacitor(16WV 0.10µF) [C29∼33,4,41,42,44]
16
VCKYCZ1CF104Z AB C Capacitor(16WV 0.10µF) [C45,56,58,59]
VCKYCZ1CF104Z AB C Capacitor(16WV 0.10µF) [C65∼68,72,76,79,80]
VRS-CZ1JD000J AA C Resistor(1/16W 0Ω ±5%) [R9,15,23,38]
17
VRS-CZ1JD000J AA C Resistor(1/16W 0Ω ±5%) [R41,46,65]
18 VRS-CZ1JD101J AA C Resistor(1/16W 100Ω ±5%) [R25∼31,40,42,56∼64]
VRS-CZ1JD103J AA C Resistor(1/16W 10KΩ ±5%) [R1∼3,10,13,36]
19
VRS-CZ1JD103J AA C Resistor(1/16W 10KΩ ±5%) [R39,47∼55]
20 VRS-CZ1JD181F AA C Resistor(1/16W 180Ω ±1%) [R43]
21 VRS-CZ1JD222J AA C Resistor(1/16W 2.2KΩ ±5%) [R4,7,18∼22,24]
23 VRS-CZ1JD511F AA C Resistor(1/16W 510Ω ±1%) [R45]
24 VRS-CZ1JD561F AA C Resistor(1/16W 560Ω ±1%) [R44]
25 RFILN0062FCPZ AC C Filter(ZJSR5101-102TA-01) [NF2,5]
26 RFILN0063FCPZ AD C EMI filter(ZJSR5101-103TA-01) [NF1,3,4,6,7,8]
27 QCNCW1160FCZZ AD C FFC connector(35pin) [CN3]
28 QCNCM0880FCZZ AF C Connector(26pin) [CN1]
29 QCNCM0923FC12 AE C Connector(12pin) [CN2]
(Unit)
901 CPWBN1567FCE3 BN E CIS control PWB
– 47-1 –
manuals4you.com
q
COPYRIGHT 2006 BY SHARP CORPORATION
All rights reserved.
Printed in Japan.
No part of this publication may be reproduced,
stored in a retrieval system, or transmitted.
In any form or by any means,
electronic, mechanical, photocopying, recording, or otherwise,
without prior written permission of the publisher.
SHARP CORPORATION
Digital Document System Group
CS PROMOTION CENTER
Yamatokoriyama, Nara 639-1186, Japan
2006 May Printed in Japan t