Professional Documents
Culture Documents
Submittal Asset Doc Loc 5695806
Submittal Asset Doc Loc 5695806
Country of Origin 39
Recycling one ton of paper saves 17 trees and 7000 gallons of water.
Please consider your environmental responsibility before using the hard copy version!
1
DESIGNED TO OUTPERFORM
THE PAST AND THE PRESENT.
Designers and engineers asked for it, so Hilti delivered: introducing the next generation HST3 metal expansion anchor. HST3 is the successor Higher load performance at the same embedment depth
of HST - the first metal expansion anchor ever to carry an approval for cracked concrete. HST3 is now suitable for an even wider range of
The new HST3 presents two embedment depths that make design more versatile. Significantly higher loads can be achieved at the same
applications and conditions for added reassurance on your daily designs. embedment depth and application on thinner slabs is approved.
Hilti HST3 is the perfect design solution for all safety relevant application for non-cracked and cracked concrete under static, seismic and
shock loading. Meets challenging design requirements with ease such as smallest edge and spacing distances in combination with highest HST3 M12 NEW HST M12
resistance values, thanks to its optimized coating, ingenious sleeve geometry and premium bolt material.
6.7kN
Recommended
Designed to perform.
Tension Load *
+67%#
4.2kN 4kN
Performs to design.
0
Optimized Performance
Embedment Depth
Higher loads is achieved by ingenious sleeve
geometry combined with its high tension
resistances, provides an increased undercut
percentage, which leads to crack retraction effect. -20mm
Best shear resistance with no compromise on 70mm 50mm 70mm
Design Flexibility ductility with the premium bolt material and cold
forming technology. Standard Reduced Standard
Minimum edge distance, spacing and member * Recommended load is based on cracked concrete C20/25, with overall factor of safety=3
thickness is allowed with an optimized coating
#
New HST3 M8 to M16 are approved with higher tension load of 33% to 67% increase, shear load up to 27% increase,
throughout the anchor which reduces expansion compared to HST.
forces.
Smaller edge and space distances with improved design and installation flexibility
Minimum edge and spacing distances are
possible thanks to HST3’s optimizes coating Hilti HST3 M12 Competitor Anchor M12
Extensive Concrete Grades throughout the anchor, which reduces
expansion forces in the system.
Due to the advanced sleeve design, application No concrete splitting may occur when placed
on concrete strength class range from C12/15 to close to edge and another anchor.
110mm 110mm
C80/95 is now possible.
55mm 55mm
Concrete splitting
2
Anchor Systems
Advantages
■ Highest resistance for geometrically challenging requirements,
e.g.reduced member thickness, shortest spacing and edge
distances
■ Design tension resistance increased by up to 66% compared
to HST
■ Minimum slab thickness: increased concrete strength class
range from C12/15 to C80/95
■ Flexibility with two embedment depths included in the ETA These are abbreviated instructions which may vary according to the application.
Always observe/follow the instructions accompanying the product or refer to
Technical data www.hilti.com/techlib.
Material composition (Galvanized) Steel, zinc-plated
(min. 5 μm);
(Stainless steel) Steel, A4 (SS316)
Head configuration Externally threaded
Ordering designation Anchor Anchor Drill bit Drill hole Drill hole Max. Max. Base plate Required Sales pack Item
size length diameter depth at depth at fixture fixture clearance tightening quantity number
embed. 1 embed. 2 thickness thickness hole torque
at embed. 1 at embed. 2
HST3 M8x75 -/10 M8 75 mm 8 mm - 60 mm - 10 mm 9 mm 20 Nm 100 pc 2105888
HST3 M8x95 -/30 M8 95 mm 8 mm - 60 mm - 30 mm 9 mm 20 Nm 80 pc 2105889
HST3 M8x115 -/50 M8 115 mm 8 mm - 60 mm - 50 mm 9 mm 20 Nm 50 pc 21058901)
HST3 M10x70 10/- M10 70mm 10 mm 53 mm 10 mm - 9 mm 20 Nm 50 pc 21139741)
1) 3 representative.
This is a non-stock item. For detailed lead time information please contact your Hilti
Hilti online: www.hilti.com.hk
226
Anchor Systems
Ordering designation Anchor Anchor Drill bit Drill hole Drill hole Max. Max. Base plate Required Sales pack Item
size length diameter depth at depth at fixture fixture clearance tightening quantity number
embed. 1 embed. 2 thickness thickness hole torque
at embed. 1 at embed. 2
HST3 M10x80 20/- M10 80mm 10 mm 53 mm - 20 mm - 9 mm 20 Nm 50 pc 21139751)
HST3 M10x90 30/10 M10 90mm 10 mm 53 mm 73 mm 30 mm 10 mm 12 mm 45 Nm 50 pc 2105712
HST3 M10x110 50/30 M10 110mm 10 mm 53 mm 73 mm 50 mm 30 mm 12 mm 45 Nm 40 pc 2105714
HST3 M10x130 70/50 M10 130 mm 10 mm 53 mm 73 mm 70 mm 50 mm 12 mm 45 Nm 25 pc 21057151)
HST3 M10x160 100/80 M10 160 mm 10 mm 53 mm 73 mm 100 mm 80 mm 12 mm 45 Nm 25 pc 21057161)
HST3 M12x85 10/- M12 85mm 12 mm 68 mm - 10 mm - 14 mm 60 Nm 25 pc 21139781)
HST3 M12x95 20/- M12 95mm 12 mm 68 mm - 20 mm - 14 mm 60 Nm 25 pc 21139791)
HST3 M12x115 40/20 M12 115mm 12 mm 68 mm 88 mm 40 mm 20 mm 14 mm 60 Nm 25 pc 2105719
HST3 M12x145 70/50 M12 145mm 12 mm 68 mm 88 mm 70 mm 50 mm 14 mm 60 Nm 25 pc 2105851
HST3 M12x185 110/90 M12 185 mm 12 mm 68 mm 88 mm 110 mm 90 mm 14 mm 60 Nm 25 pc 21058531)
HST3 M12x215 140/120 M12 215 mm 12 mm 68 mm 88 mm 140 mm 120 mm 14 mm 60 Nm 25 pc 2105854
HST3 M12x235 160/140 M12 235 mm 12 mm 68 mm 88 mm 160 mm 140 mm 14 mm 60 Nm 25 pc 21058551)
HST3 M12x255 180/160 M12 255 mm 12 mm 68 mm 88 mm 180 mm 160 mm 14 mm 60 Nm 25 pc 21058561)
HST3 M16x115 15/- M16 115mm 16 mm 86 mm 15 mm - 18 mm 110 Nm 12 pc 21140531)
HST3 M16x145 45/25 M16 145 mm 16 mm 86 mm 106 mm 45 mm 25 mm 18 mm 110 Nm 12 pc 2105859
HST3 M16x170 70/50 M16 170 mm 16 mm 86 mm 106 mm 70 mm 50 mm 18 mm 110 Nm 12 pc 2105860
HST3 M16x220 120/100 M16 220 mm 16 mm 86 mm 106 mm 120 mm 100 mm 18 mm 110 Nm 12 pc 21058611)
HST3 M16x260 160/140 M16 260 mm 16 mm 86 mm 106 mm 160 mm 140 mm 18 mm 110 Nm 12 pc 21058621)
HST3 M20x170 -/30 M20 170 mm 20 mm - 140 mm - 30 mm 22 mm 240 Nm 5 pc 2105891
HST3 M20x200 -/60 M20 200 mm 20 mm - 140 mm - 60 mm 22 mm 240 Nm 5 pc 2105892
HST3 M20x260 -/120 M20 260 mm 20 mm - 140 mm - 120 mm 22 mm 240 Nm 5 pc 21058931)
HST3 M24x200 -/30 M24 200 mm 24 mm - 170 mm - 30 mm 26 mm 300 Nm 5 pc 2105894
HST3 M24x230 -/60 M24 230 mm 24 mm - 170 mm - 60 mm 26 mm 300 Nm 5 pc 21058951)
1)
This is a non-stock item. For detailed lead time information please contact your Hilti representative.
Ordering designation Anchor Anchor Drill bit Drill hole Drill hole Max. Max. Base plate Required Sales pack Item
size length diameter depth at depth at fixture fixture clearance tightening quantity number
embed. 1 embed. 2 thickness thickness hole torque
at embed. 1 at embed. 2
HST3-R M8x75 -/10 M8 75 mm 8 mm - 60 mm - 10 mm 9 mm 20 Nm 50 pc 2105896
HST3-R M8x95 -/30 M8 95 mm 8 mm - 60 mm - 30 mm 9 mm 20 Nm 50 pc 2105897
HST3-R M8x115 -/50 M8 115 mm 8 mm - 60 mm - 50 mm 9 mm 20 Nm 50 pc 2105898
HST3-R M10x70 10/- M10 70mm 10 mm 53 mm - 10 mm - 12 mm 45 Nm 50 pc 21139761)
HST3-R M10x80 20/- M10 80mm 10 mm 53 mm - 20 mm - 12 mm 45 Nm 50 pc 2113977
HST3-R M10x90 30/10 M10 90 mm 10 mm 53 mm 73 mm 30 mm 10 mm 12 mm 45 Nm 50 pc 2105864
HST3-R M10x110 50/30 M10 110 mm 10 mm 53 mm 73 mm 50 mm 30 mm 12 mm 45 Nm 40 pc 2105866
HST3-R M10x130 70/50 M10 130 mm 10 mm 53 mm 73 mm 70 mm 50 mm 12 mm 45 Nm 25 pc 2105867
HST3-R M10x160 100/80 M10 160 mm 10 mm 53 mm 73 mm 100 mm 80 mm 12 mm 45 Nm 25 pc 2105868
HST3-R M12x85 10/- M12 85mm 12 mm 68 mm - 10 mm - 14 mm 60 Nm 25 pc 21140511)
HST3-R M12x95 20/- M12 95mm 12 mm 68 mm - 20 mm - 14 mm 60 Nm 25 pc 2114052
HST3-R M12x115 40/20 M12 115 mm 12 mm 68 mm 88 mm 40 mm 20 mm 14 mm 60 Nm 25 pc 2105870
HST3-R M12x145 70/50 M12 145 mm 12 mm 68 mm 88 mm 70 mm 50 mm 14 mm 60 Nm 25 pc 2105872
HST3-R M12x185 110/90 M12 185 mm 12 mm 68 mm 88 mm 110 mm 90 mm 14 mm 60 Nm 25 pc 2105874
HST3-R M12x215 140/120 M12 215 mm 12 mm 68 mm 88 mm 140 mm 120 mm 14 mm 60 Nm 25 pc 2105875
HST3-R M16x115 15/- M16 115mm 16 mm 86 mm - 15 mm - 18 mm 110 Nm 12 pc 21140571)
HST3-R M16x145 45/25 M16 145 mm 16 mm 86 mm 106 mm 45 mm 25 mm 18 mm 110 Nm 12 pc 2105877
HST3-R M16x170 70/50 M16 170 mm 16 mm 86 mm 106 mm 70 mm 50 mm 18 mm 110 Nm 12 pc 2105878
HST3-R M16x220 120/100 M16 220 mm 16 mm 86 mm 106 mm 120 mm 100 mm 18 mm 110 Nm 12 pc 2105879
HST3-R M16x260 160/140 M16 260 mm 16 mm 86 mm 106 mm 160 mm 140 mm 18 mm 110 Nm 12 pc 2105880
HST3-R M16x300 200/180 M16 300 mm 16 mm 86 mm 106 mm 200 mm 180 mm 18 mm 110 Nm 12 pc 2105881
HST3-R M20X170 -/30 M20 170 mm 20 mm - 140 mm - 30 mm 22 mm 240 Nm 5 pc 2105899
HST3-R M20X200 -/60 M20 200 mm 20 mm - 140 mm - 60 mm 22 mm 240 Nm 5 pc 2105900
HST3-R M24X200 -/30 M24 200 mm 24 mm - 170 mm - 30 mm 26 mm 300 Nm 5 pc 2105901
HST3-R M24X230 -/60 M24 230 mm 24 mm - 170 mm - 60 mm 26 mm 300 Nm 5 pc 2105902
1)
This is a non-stock item. For detailed lead time information please contact your Hilti representative.
4
Customer Hotline: Hong Kong 8228 8118 Macau 00800 8228 8118
227
2 November 2015
Ref: 071/MA/FL/15
We are pleased to inform you that HST3 stud anchor is phased-in as an upgraded version of HST. The
new HST3 anchor series is of equivalent or better specifications than current HST anchor. You can see
the equivalent items below.
Nomenclature
HST3 M10 x90 30/10
Anchor type Diameter Anchor length Fixture thickness 1 / 2
HST3 HST
Head mark Head mark
1. Load performance
HST3 exhibits higher or equivalent load performance in terms of tension and shear loads,
compared to HST. HST3 can be applied in any case to directly replace HST. Revision of
calculation can be carried out by Hilti Profis Anchor software or as per Hilti anchor design manual.
HST3 can be applied on concrete cube strength of 15N/mm2 to 95N/mm2, cracked or uncracked.
HST3 requires a smaller or equivalent edge and anchor spacing distances (refer to Hilti anchor
design manual).
4. Setting depths
HST3 allows two options of embedment depths; HST allows single embedment depth only.
5. Drilling methods
Three different drilling methods (as below) are approved to be used in HST3 system, while only
hammer drilling can be used in HST system.
i) Hammer drilling
ii) Diamond coring
iii) Hollow drill bit ( -Dustless solution)
Other minor differences and detailed technical information can be referred to Hilti anchor design manual.
Should you have any enquiry, please feel free our customer service hotline at 8228 8118.
Yours faithfully,
Fean Lee
Product Manager
Hilti (Hong Kong) Ltd.
6
HST3 HST3
Metal expansion anchor Metal expansion anchor
HST3 Metal expansion anchor Basic loading data (for a single anchor)
7
HST3 [kN] 10,0 12,1 15,9 16,9 26,6 25,0 37,5 48,5 53,1
HST3-R [kN] 10,0 12,1 15,9 16,9 26,6 25,0 37,5 48,5 53,1
Shear VRu,m
HST3 [kN] 14,5 23,0 24,8 35,7 37,2 57,2 58,1 88,1 98,7
Concrete Tensile Seismic Fire ETA European CE PROFIS HST3-R [kN] 16,5 26,9 26,6 32,7 38,5 51,0 66,8 102,1 120,8
(uncracked) zone ETA-C1/C2 Technical conformity Anchor
Approval design
Software
Characteristic resistence
Anchor size M8 M10 M12 M16 M20 M24
Eff. Anchorage depth hef [mm] 47 40 60 50 70 65 85 101 125
Non-cracked concrete
Tensile NRk
Hammer Diamond Hollow drill-
HST3 [kN] 12,0 12,8 20,0 17,9 25,0 26,5 39,6 51,3 60,0
drilled holes drilled holes bit drilling
HST3-R [kN] 12,0 12,8 20,0 17,9 25,0 26,5 39,6 51,3 60,0
Shear VRk
HST3 [kN] 13,8 21,9 23,6 34,0 35,4 54,5 55,3 83,9 94,0
Approvals / certificates HST3-R [kN] 15,7 25,6 25,3 31,1 36,7 48,6 63,6 97,2 115,0
Description Authority / Laboratory No. / date of issue Cracked concrete
European technical approval a) DIBt, Berlin ETA-98/0001 / 2015-11-06 Tensile NRk
Fire test report DIBt, Berlin ETA-98/0001 / 2015-11-06 HST3 [kN] 7,5 9,1 12,0 12,7 20,0 18,9 28,2 36,5 40,0
a) All data for HST3 in concrete strength class C20/25 to C50/60 given in this section according to ETA-98/0001,
issue 2015-11-06. Data for other concrete strength classes according to Hilti Technical Data assessment. HST3-R [kN] 7,5 9,1 12,0 12,7 20,0 18,9 28,2 36,5 40,0
Shear VRk
HST3 [kN] 13,8 21,9 23,6 34,0 35,4 54,5 55,3 83,9 94,0
HST3-R [kN] 15,7 24,3 25,3 31,1 36,7 48,6 63,6 97,2 115,0
8
Anchor dimensions
Non-cracked concrete
Tensile Nrec a)
HST3 [kN] 4,0 4,3 6,7 6,0 8,3 8,8 13,2 17,1 20,0
HST3-R [kN] 4,0 4,3 6,7 6,0 8,3 8,8 13,2 17,1 20,0
Shear Vrec a)
HST3 [kN] 4,6 7,3 7,9 11,3 11,8 18,2 18,4 28,0 31,3
HST3-R [kN] 5,2 8,5 8,4 10,4 12,2 16,2 21,2 32,4 38,3
Cracked concrete
Tensile Nrec a)
HST3 [kN] 2,5 3,0 4,0 4,2 6,7 6,3 9,4 12,2 13,3
HST3-R [kN] 2,5 3,0 4,0 4,2 6,7 6,3 9,4 12,2 13,3
Shear Vrec a)
HST3 [kN] 4,6 7,3 7,9 11,3 11,8 18,2 18,4 28,0 31,3
HST3-R [kN] 5,2 8,1 8,4 10,4 12,2 16,2 21,2 32,4 38,3
a) With overall global safety factor = 3. The recommended loads vary according to the safety factor requirements
from national regulations.
Setting instructions
Installation equipment
Anchor size M8 M10 M12 M16 M20 M24
Rotary hammer TE2(-A) – TE30(-A) TE40 – TE70
Diamond coring tool DD-30W, DD-EC1
Setting tool Setting tool HS-SC -
Hollow drill bit - TE-CD, TE-YD
Other tools hammer, torque wrench, blow out pump
9
Setting instruction for M10
Setting instruction for M16
10
Setting instruction for M24 hmin
h1
hnom
tfix hef
For detailed informations on installation see instruction for use given with the package of the product.
11
Critical spacing for splitting [mm] 141 141 188 168 180 180 240 splitting failure and 210 255
failure and concrete cone concrete cone failure [mm] 150 210 195 255
failure [mm] 141 141 120 180 180
Critical edge distance for [mm] 90 140 104 170
Critical edge distance for [mm] 71 71 94 84 90 90 120 splitting failure and 105 128
splitting failure and concrete cone failure [mm] 75 105 98 128
concrete cone failure [mm] 71 71 60 90 90
a) For concrete classes from C20/25 to C50/60 data covered by ETA-98/0001 issue 2015-11-06.
a) For concrete classes C20/25 to C50/60 data covered by ETA-98/0001 issue 2015-11-06. b) Data covered by Hilti Technical Data.
b) Data covered by Hilti Technical Data.
For spacing (edge distance) smaller than critical spacing (critical edge distance) the design loads have to be reduced.
For spacing (edge distance) smaller than critical spacing (critical edge distance) the design loads have to be reduced.
12
distance
in cracked concrete [mm] 120 80 100 125 230
HST3-R/
[mm] 180 180 240 140 295
Critical spacing for splitting failure and [mm] 384 404 375 500
concrete cone failure [mm] 303 303 375 375
Critical edge distance for splitting [mm] 192 202 188 250
failure and concrete cone failure [mm] 152 152 188 188
a) For concrete classes from C20/25 to C50/60 data covered by ETA-98/0001 issue 2015-11-06.
b) Data covered by Hilti Technical Data.
For spacing (edge distance) smaller than critical spacing (critical edge distance) the design loads have to be reduced.
Design concrete cone resistance NRd,sp = N0Rd,c fB f1,N f2,N f3,N fre,N Influence of base material thickness
Design splitting resistance a) NRd,sp = N0Rd,c fB f1,sp f2,sp f3,sp f h,sp fre,N 1.5
h/hef 2,0 2,2 2,4 2,6 2,8 3,0 3,2 3,4 3,6
Anchor size M8 M10 M12 M16 M20 M24
1,00 1,07 1,13 1,19 1,25 1,31 1,37 1,42 1,48 1,50
Effective anchorage depth hef 47 40 60 50 70 65 85 101 125
Non cracked concrete
HST3 [kN] 10,8 8,5 15,6 11,9 19,7 17,6 26,4 34,2 47,1 Influence of reinforcement
N0Rd,c
HST3-R [kN] 10,8 8,5 15,6 11,9 19,7 17,6 26,4 34,2 47,1 Anchor size M8 M10 M12 M16 M20 M24
Cracked concrete 0,74 a) 0,70 a) 0,80 a) 0,75 a) 0,85 a) 0,83 a) 0,93 a) 1,00 1,00
HST3 [kN] 7,7 6,1 11,2 8,5 14,1 12,6 18,8 24,4 33,5
N0Rd,c
HST3-R [kN] 7,7 6,1 11,2 8,5 14,1 12,6 18,8 24,4 33,5
a) Splitting resistance must only be considered for non-cracked concrete
Influencing factors
C12/15
C16/20
C55/67
C60/75
C70/85
C80/95
C 20/25
C 25/30
C 30/37
C 35/45
C 40/50
C 45/55
C 50/60
B
fB,c = (fck,cube/25N/mm²)1/2 a) 0,77 0,89 1,00 1,10 1,22 1,34 1,41 1,48 1,55 1,64 1,73 1,84 1,95
For HST3 M8, M10, M12 and M16
fB,p 0,68 0,85 1,00 1,10 1,22 1,34 1,41 1,48 1,55 1,55 1,55 1,55 1,55
13
For HST3 M20 and M24
fB,p 0,68 0,85 1,00 1,10 1,22 1,34 1,41 1,48 1,55 1,60 1,66 1,72 1,78
Basic design shear resistance
a) fck,cube = concrete compressive strength, measured on cubes with 150 mm side length
Influence of edge distance a) Anchor size M8 M10 M12 M16 M20 M24
c/ccr,N Effective anchorage depth hef 47 40 60 50 70 65 85 101 125
0,1 0,2 0,3 0,4 0,5 0,6 0,7 0,8 0,9 1 HST3 [kN] 11,0 17,5 18,9 27,2 28,3 43,6 44,2 67,1 62,7
c/ccr,sp VRd,s
HST3-R [kN] 12,6 20,5 20,2 24,9 29,4 38,9 50,9 77,8 88,5
f1,N =
0,73 0,76 0,79 0,82 0,85 0,88 0,91 0,94 0,97 1,00
f1,sp =
1
f2,N =
0,55 0,60 0,65 0,70 0,75 0,80 0,85 0,90 0,95 1,00 Anchor size M8 M10 M12 M16 M20 M24
f2,sp =
k-factor for C20/25 to C80/95 2,6 2,7 2,8 3,4 3,2 2,5
a) The edge distance shall not be smaller than the minimum edge distance c min given in the table with the setting details.
These influencing factors must be considered for every edge distance. k-factor for C12/15 1 2 2 2 2 2
a) NRd,c: Design concrete cone resistance
a)
Influence of anchor spacing
1
s/scr,N
0,1 0,2 0,3 0,4 0,5 0,6 0,7 0,8 0,9 1 Anchor size M8 M10 M12 M16 M20 M24
s/scr,sp
Effective anchorage depth hef 47 40 60 50 70 65 85 101 125
f3,N =
0,55 0,60 0,65 0,70 0,75 0,80 0,85 0,90 0,95 1,00 Non-cracked concrete
f3,sp = HST3 [kN]
a) The anchor spacing shall not be smaller than the minimum anchor spacing s min given in the table with the setting V0Rd,c 5,9 8,5 8,6 11,6 11,7 18,8 18,9 27,3 37,1
HST3-R [kN]
details. This influencing factor must be considered for every anchor spacing.
Cracked concrete
HST3 [kN]
V0Rd,c 4,2 6,0 6,1 8,2 8,3 13,3 13,4 19,3 26,3
HST3-R [kN]
a) For anchor groups only the anchors close to the edge must be considered.
130 01 / 2016 01 / 2016 131
HST3 HST3
Metal expansion anchor Metal expansion anchor
C12/15
C16/20
C55/67
C60/75
C70/85
C80/95
C 20/25
C 25/30
C 30/37
C 35/45
C 40/50
C 45/55
C 50/60
c/d 4 6 8 10 15 20 30 40
fc = (d / c)0,19 0,77 0,71 0,67 0,65 0,60 0,57 0,52 0,50
fB,c = (fck,cube/25N/mm²)1/2 a) 0,77 0,89 1,00 1,10 1,22 1,34 1,41 1,48 1,55 1,64 1,73 1,84 1,95
a) The edge distance shall not be smaller than the minimum edge distance c min.
a) fck,cube = concrete compressive strength, measured on cubes with 150 mm side length
Influence of angle between load applied and the direction perpendicular to the free edge
Angle ß 0° 10° 20° 30° 40° 50° 60° 70° 80° 90°
Combined tension and shear loading
1,00 1,01 1,05 1,13 1,24 1,40 1,64 1,97 2,32 2,50 For combined tension and shear loading see section “Anchor Design”.
14
Single Group of two anchors s/hef
c/hef
anchor 0,75 1,50 2,25 3,00 3,75 4,50 5,25 6,00 6,75 7,50 8,25 9,00 9,75 10,50 11,25
0,50 0,35 0,27 0,35 0,35 0,35 0,35 0,35 0,35 0,35 0,35 0,35 0,35 0,35 0,35 0,35 0,35
0,75 0,65 0,43 0,54 0,65 0,65 0,65 0,65 0,65 0,65 0,65 0,65 0,65 0,65 0,65 0,65 0,65
1,00 1,00 0,63 0,75 0,88 1,00 1,00 1,00 1,00 1,00 1,00 1,00 1,00 1,00 1,00 1,00 1,00
1,25 1,40 0,84 0,98 1,12 1,26 1,40 1,40 1,40 1,40 1,40 1,40 1,40 1,40 1,40 1,40 1,40
1,50 1,84 1,07 1,22 1,38 1,53 1,68 1,84 1,84 1,84 1,84 1,84 1,84 1,84 1,84 1,84 1,84
1,75 2,32 1,32 1,49 1,65 1,82 1,98 2,15 2,32 2,32 2,32 2,32 2,32 2,32 2,32 2,32 2,32
2,00 2,83 1,59 1,77 1,94 2,12 2,30 2,47 2,65 2,83 2,83 2,83 2,83 2,83 2,83 2,83 2,83
2,25 3,38 1,88 2,06 2,25 2,44 2,63 2,81 3,00 3,19 3,38 3,38 3,38 3,38 3,38 3,38 3,38
2,50 3,95 2,17 2,37 2,57 2,77 2,96 3,16 3,36 3,56 3,76 3,95 3,95 3,95 3,95 3,95 3,95
2,75 4,56 2,49 2,69 2,90 3,11 3,32 3,52 3,73 3,94 4,15 4,35 4,56 4,56 4,56 4,56 4,56
3,00 5,20 2,81 3,03 3,25 3,46 3,68 3,90 4,11 4,33 4,55 4,76 4,98 5,20 5,20 5,20 5,20
3,25 5,86 3,15 3,38 3,61 3,83 4,06 4,28 4,51 4,73 4,96 5,18 5,41 5,63 5,86 5,86 5,86
3,50 6,55 3,51 3,74 3,98 4,21 4,44 4,68 4,91 5,14 5,38 5,61 5,85 6,08 6,31 6,55 6,55
3,75 7,26 3,87 4,12 4,36 4,60 4,84 5,08 5,33 5,57 5,81 6,05 6,29 6,54 6,78 7,02 7,26
4,00 8,00 4,25 4,50 4,75 5,00 5,25 5,50 5,75 6,00 6,25 6,50 6,75 7,00 7,25 7,50 7,75
4,25 8,76 4,64 4,90 5,15 5,41 5,67 5,93 6,18 6,44 6,70 6,96 7,22 7,47 7,73 7,99 8,25
4,50 9,55 5,04 5,30 5,57 5,83 6,10 6,36 6,63 6,89 7,16 7,42 7,69 7,95 8,22 8,49 8,75
4,75 10,35 5,45 5,72 5,99 6,27 6,54 6,81 7,08 7,36 7,63 7,90 8,17 8,45 8,72 8,99 9,26
5,00 11,18 5,87 6,15 6,43 6,71 6,99 7,27 7,55 7,83 8,11 8,39 8,66 8,94 9,22 9,50 9,78
5,25 12,03 6,30 6,59 6,87 7,16 7,45 7,73 8,02 8,31 8,59 8,88 9,17 9,45 9,74 10,02 10,31
5,50 12,90 6,74 7,04 7,33 7,62 7,92 8,21 8,50 8,79 9,09 9,38 9,67 9,97 10,26 10,55 10,85
a) The anchor spacing and the edge distance shall not be smaller than the minimum anchor spacing s min and the minimum
edge distance cmin.
2 November 2015
Ref: 072/MA/FL/15
Should you have any enquiry, please feel free our customer service hotline at 8228 8118.
Yours faithfully,
Fean Lee
Product Manager
Hilti (Hong Kong) Ltd.
Design at a Click Dependable Documents and Engineering Support on Call Testing Service for Quality
Hilti PROFIS Anchor software Approvals Hilti engineers are available Assurance
makes it easy to identify the Hilti anchors are designed and tested to assist you in your design Independent Hilti Testing
optimal Hilti anchor for all your under European Technical Approvals and project submission for Laboratory is HOKLAS accredited
anchor applications. (ETA) for cracked and uncracked approvals, at no additional cost. for onsite anchor loading testing
concrete, as well as dynamic loading To contractors, we offer free complying with BS5080.
When you design with PROFIS
applications e.g shock, seismic, etc. on-site installation card training
Anchor, you get the added Assuring your anchor design is
with certificate.
reassurance that your designs You are well supported with properly and safely implemented
meet codal provisions of the comprehensive technical information You can access our technical at the job site, when workmanship
European Technical Approval and test reports for your project support 24/7; contact our Design is verified.
Guidelines (ETAG) with just one approval at Buildings Department, Engineers, Engineering Hotline
click! Housing Authority, Architectural Services 2773 4731, or visit hilti.com.hk.
Department, etc.
40
6 7