Professional Documents
Culture Documents
C
2 Which DAQ board will allow for the detection of a 2.1 mV change in a signal if a 0-10 volt range was
selected?
12-bit board
A
16-bit board
B
Both A. and B.
C
None of the above.
D
3 What is the result in subarray after the following code has executed?
a 1-D Array of {4, 6, 8}
A
a 1-D Array of {6, 8, 10}
B
a 1-D Array of {2, 4, 6}
C
a 1-D Array of {8, 16, 32}
D
4 What is the result in Output Array after the following code has executed?
5 Clicking on the _____ button allows you to bypass a node in the Block Diagram without single-
stepping through the node.
Step Over
A
Step Out
B
Step Through
C
Step Into
D
6 Which of the following is a required terminal connection for the Append Table to Report VI shown
below?
row headers
A
report in
B
column width (1)
C
column headers
D
7 What is the result in Array after the following code has executed?
D
Front Panel
A
Block Diagram
B
Both A. and B.
C
None of the above
D
11 Which of the following display options are available for strings on the Front Panel?
‘\’ Codes
A
Password
B
Hex
C
All of the above
D
14 To place an Express VI on the Block Diagram you would select it from the:
Tools Palette
A
Functions Palette
B
Icon Palette
C
Controls Palette
D
Top of Form
16 DAQmx channels and virtual channels are a collection of property settings that include all of the
following, EXCEPT:
type of measurement.
A
physical channel.
B
base I/O address.
C
scaling information.
D
29 Which of the following terminals supplies the current iteration number of a For or While Loop?
A
B
C
D
17
The
____
_
dete
rmin
es
the
total
num
ber
of
time
sa
For
Loop
will
exec
ute
and
the
____
_
retur
ns
the
num
ber
of
time
s the
loop
has
exec
uted
minu
s
one.
A coun
t
termi
nal,
;
condi
tional
termi
nal,
B coun
t
termi
nal,
;
iterati
on
termi
nal
C itera
tion
termi
nal,
;
count
termi
nal,
D cond
itiona
l
termi
nal,
;
count
termi
nal,
18 What is the result in Array after the following code has executed?
If an Error Cluster displays a non-zero error code coupled with a status of FALSE, it signals:
21 If Number equals -49, then what is the result in Square Root Value after the following code has
executed?
-99999, and a dialog box with an error message will display
A
-7
B
An error will occur and the code will not execute because Number is negative.
C
7
D
22 Which chart update mode shows running data continuously scrolling from left to right across the
chart?
Step Chart
A
Scope Chart
B
Sweep Chart
C
Strip Chart
D
23 What is the result in Array after the following code has executed?
24 Which of the following methods will create an XY Graph with two plots?
Bundle the X and Y array pairs together into two clusters and then create an array of these two clusters.
A
Create a single array of each of the X arrays and Y arrays in an X, Y, X, Y pattern.
B
Create a single cluster from two arrays of X values and two arrays of Y values in an X, Y, X, Y pattern.
C
Bundle the X and Y array pairs together into two clusters and create a cluster of these two clusters.
D
Arrays
A
Clusters
B
Both A. and B.
C
None of the above
D
26 Which of the following is a recommended terminal connection for the Append Text Table to
Report VI shown below?
Clusters can hold multiple data types, while Arrays are limited to one data type.
A
Array elements are ordered, but Cluster elements are not.
B
Arrays cannot contain both Indicators and Controls, but Clusters can contain both.
C
Clusters cannot be used to pass data to SubVIs, while Arrays can be used.
D
29 Which of the following terminals supplies the current iteration number of a For or While Loop?
A
B
C
D
If two events occur at the same time, only the first event will be handled and the second will be lost.
A
The diagram becomes significantly larger when changing from a General VI to a State Machine VI.
B
A State Machine VI can only traverse states in order.
C
State Machines cannot acquire data or use DAQ functions.
D
33 Right clicking on the Block Diagram will cause which palette to display?
Tools Palette
A
Controls Palette
B
Printing Palette
C
Functions Palette
D
34 Which of the following statements is not true regarding the figure below?
It is not necessary to wire the count (N) terminal because auto-indexing is enabled.
A
Elements of Input Array enter the loop one at a time.
B
Output Array is the same size as Input Array.
C
If you disable auto-indexing on the right side of the For Loop, the output is still a 1-D Array.
D
All of the above statements are true
E
35 When creating a SubVI icon, the number of input terminals must match the number of:
output terminals.
A
Controls.
B
Indicators.
C
None of the above.
D
pass the error to the next node without executing the code in which the error occurred.
A
freeze the program and wait for user interaction.
B
immediately display a pop-up window describing the error.
C
execute normally.
D
39 Which of the following will continuously display multiple plots on the same Waveform Chart until the stop
button is pressed?
40 To access a graphical representation of all of the SubVI's and nodes that are called in the current VI,
then: