Professional Documents
Culture Documents
LED TV
MS036631 Chassis
WARNING
This service information is designed for experienced repair technicians only and is not designed for use by the general public.
It does not contain warnings or cautions to advise non-technical individuals of potential dangers in attempting to service a product.
Products powered by electricity should be serviced or repaired only by experienced professional technicians. Any attempt to
service or repair the product or products dealt with in this service information by anyone else could result in serious injury or death.
Contents
2、 Introduction.....................................................................................................................4
4、 Installation...................................................................................................................... 6-9
5、 Remote Controller...........................................................................................................10
6、 TV Operation..................................................................................................................11-14
7、 Trouble shooting.............................................................................................................15
-1-
SAFETY AND WARNINGS
IMPORTANT SAFETY INSTRUCTION
1) Read these instructions. CAUTION
2) Keep these instructions. RISK OF ELECTRIC SHOCK
DO NOT OPEN!
3) Heed all warnings.
4) Follow all instructions. CAUTION
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO
5) Do not use this apparatus near water. NOT REMOVE COVER (OR BACK).NO USER
6) Clean only with dry cloth. SERVICEABLE PARTS INSIDE. REFER SERVICING
7) Do not block any ventilation openings, install TO QUALIFIED SERVICE PERSONNEL.
in accordance with the instructions.
8) Do not install near any heat sources such as The symbol indicates that dangerous
radiations, heat registers, stoves, or other voltages constituting a risk of electric shock
apparatus (including amplifiers) that produce are present within this unit.
heat.
9) Do not defeat the safety purpose of the The symbol indicates that there are
polarized plug. If the provided plug does not fit important operating and maintenance
into your outlet, consult an electrician for instructions in the literaturaccompanying this
replacement of the obsolete outlet. unit.
10) Protected the power cord from being walked WARNING:
on or pinched particularly at plugs, convenience To reduce the risk of fire or electric shock, do
receptacles, and the point where they exit from not expose this apparatus to rain or moisture.
the apparatus.
11) Only use attachments/accessories specified
by the manufacturer. WARNING:
12) Unplug this apparatus during lighting The batteries shall not be exposed to
storms or when unused for long periods of time. excessive heat such as sunshine, fire or the
13) Refer all servicing to qualified service like.
personnel. Servicing is required when the
apparatus has been damaged in any way, such as
power-supply cord or plug is damaged, liquid
has been spilled or objects have fallen into the
apparatus, the apparatus has been exposed to This symbol indicates that this product
rain or moisture, does not operate normally, or incorporates double insulation between
has been dropped. hazardous mains voltage and user accessible
parts. When servicing use only
14) Mains plug is used as the disconnect device,
identical replacement parts.
the disconnect device shall remain readily
operable.
15) The ventilation should not be impeded by
covering the ventilation openings with items,
such as newspapers, table-cloth, curtains, etc.
16) No naked flame sources, such as lighted
candles, should be placed on the apparatus.
17) Attention should be drawn to the This marking indicates that this product should
environmental aspects of battery disposal. not be disposed with other household wastes
18) The use of apparatus in moderate climate. throughout the EU. To prevent possible harm to
19) The apparatus shall not be exposed to the environment or human health from
dripping or splashing and that no objects filled uncontrolled waste disposal, recycle it
with liquids, such as vases, shall be placed on responsibly to promote the sustainable reuse of
the apparatus. material resources. To return your used device,
please use the return and collection systems or
contact the retailer where the product was
purchased. They can take this product for
environmental safe recycling.
-2-
SAFETY AND WARNINGS
High voltages are used in the operation of this television Never stand on, lean on, or suddenly push the television or
receiver. Do not remove the cabinet back from your set. its stand. You should pay special attention to children.
Refer servicing to qualified service personnel. Serious injury may result if it falls.
To prevent fire or electrical shock hazard, do not expose Do not place your television on an unstable cart, stand,
the television receiver to rain or moisture. shelf or table. Serious injury to an individual , and damage
to the television, may result if it falls.
Do not drop or push objects into the television cabinet When the television receiver is not used for an
slots or openings. Never spill any kind of liquid on the extended period of time, it is advisable to disconnect
television receiver. the AC power cord from the AC outlet.
Do not block the ventilation holes in the back cover. Avoid exposing the television receiver to direct sunlight
Adequate ventilation is essential to prevent failure of and other sources of heat. Do not stand the television
electrical components. receiver directly on other products which give off heat,
e.g. video cassette players and audio amplifiers. Do not
place naked flame sources, such as lighted candles on
the television.
Dim:515*320mm(不包括底座)
Do not trap the power supply cord under the television If the television is to be built into a compartment or similar
receiver. enclosure, the minimum distances must be maintained. Heat
build-up can reduce the service life of your television, and
can also be dangerous.
-3-
INTRODUCTION
Main parameter
Model 32 inch
Resolution 1366x768
Aspect Ratio 16 : 9
TV System PAL/NTSC/SECAM
Video Signal System PAL/NTSC/SECAM
Receiving Channel 1-99
Input Power Voltage AC 100-240V 50/60Hz
Power consumption 40W
Audio Output Power(THD 7%) 2 x 8W
Analog RGB(VGA) x 1
Signal Input/Output
High-Definition Multimedia Interfac e (HDMI) x 3
Composite Video Input x 1
Audio Input x 1
Headphone x 1
YCb (Pb )Cr (P r) x 1
USB x 1
COAXIAL x 1
RF x 1
Horizontal definition(TV line ) Composite Video input >=350
Y Cb(Pb ) Cr(Pr) >=400
-4-
WALL MOUNT INSTALLATION
Step One: Use the expansion bolts(4*36PWA) to fix the wall mount brackets into the wall.
wall
Step Two: Fix the wall mount screws M4x5mm/4pcs, into the rear side of the LCD TV,using the
tongue of 8kgf.cm.
* The TV appearance subject to material object.
Step Three: Put the LCD TV with wall mount screws onto the wall mount brackets.
Warning: the angle between the TV and wall must not be bigger than 3º.
wall
-5-
INSTALLATION
Front panel
1 3
2
≤8m
KEYBOARD
The keyboard is located at the bottom left near the right side of signal indicator.
Rocker
Bottom
1. Middle Button: press longtime for “power” function; press once for “source” function
2. Up/Down: CH+/-
3. Left/Righ: VOL-/+
REAR AV Connections
COAXIAL
-6-
INSTALLATION
ANTENNA
Note:
Aerial connections: IEC(female).
Input impendance: 75 unbalanced.
PC
STEPS:
Be sure both the TV and computer are Power off.
COAXIAL
-7-
INSTALLATION
1 800*600 60 37.88
2 1024*768 60 48.36
3 1360*768 60 47.7
1 800*600 60 37.88
2 1024*768 60 48.36
3 1360*768 60 47.7
4 1280*768 60 47.3
5 1920*1080 60 67.5
-8-
INSTALLATION
AV EQUIPMENT
This TV provides one group of AV, one group of YPbPr for convenient connection to VCR, DVD or other
video equipment. Please refer to the owner's manual of the equipment to be connected as well.
You can use the input terminals on TV set rear as follows.
COAXIAL
HDMI
Y Yellow (video)
R Red (audio R)
G B R W R
W White(audio L)
R Red(Pr or Cr)
B Blue(Pb or Cb)
G Green(Y)
W R G B R
Y W R
VIDEO EQUIPMENT
W R Y
TO VIDEO
TO AUDIO OUTPUTS OUTPUTS
It can be connected to the following appliances: VCR, multi disc player, DVD, camcorder, video game or stereo system, etc...
YPbPr can support these video fomats: 480i, 576i, 480p, 576p, 720p, 1080i, 1080p.
Note: 1.Video and YPbPr share one audio channel.
2.When HDMI port get DVI signal, the "AV Audio" channel is changed to receive the audio for HDMI port.
3.Sometimes it will not support in different device because the device supplys nonstandard signal.
-9-
Service Manual
Model No.:
B Board
A Board
No. Description
A Board Mainboard
B Board Power Supply
- 08 -
Service Manual
Model No.:
- 09 -
Service Manual
Model No.:
- 10 -
Service Manual
Model No.:
3-4-1.Connector de finition
- 11 -
Service Manual
Model No.:
/D\GRZQWKHXQLWVRWKDWUHDUFRYHU
faces upward
5HPRYHWKHVFUHZIURPWKH
UHDUFRYHULQGLFDWHGZLWKż
7KHQUHPRYHWKHSHGHVWDO
5HPRYHWKHVHVFUHZLQGLFDWHGRQ
¿JXUHDERYHE\ż
7KHQUHPRYHWKHEDFNFRYHUIURPWKH
unit.
- 12 -
Service Manual
Model No.:
5HPRYHWKH0DLQERDUG
- 13 -
Service Manual
Model No.:
- 14 -
5 4 3 2 1
IC
200mA DVDD_DDR
50mA AVDD_DMPLL
开机后 开机后
50mA AVDD_AU33
50mA AVDD3P3_ADC
50mA AVDD3P3_ETH
+12V_Normal +5V_Normal/2A
C 100mA AVDD_DDR_DATA C
50mA +3.3_NAND
220mA +3.3V_TU
AS1117L-3.3
1000mA +5V_MHL
+5V_Panel
B B
+5V_USB
1000mA +12_AMP
+12V_Normal +12V_Panel
A 晨星软件研发(深圳)有限公司 A
Title
变压器/ZY-T0171/A9/EQ32 2路输出/12V/18V
二极管-整流PS208 2A/70A/1KV/1.2V/DO-15编带52 二极管-肖特基/STB10100VDC 10A/80A/100V/0.5V/ TO-263 强茂低VF
二极管-整流PS208 2A/70A/1KV/1.2V/DO-27编带52 强茂 2012-10-25 穿心磁珠/10Ω-25%-3.5*6*0.8mm,编带52
二极管-整流PS208 2A/70A/1KV/1.2V/DO-27编带52 强茂 欧规组件统一改为450V耐压 贴片电容/2200PF-50V-K-0201-X7R
二极管-整流PS208 2A/70A/1KV/1.2V/DO-15编带52 2013-5-23
美国市场改为400V耐压 PT3 NC/PM38
2012-11-6
2
FB14
D803 D804 改善低温-10oC不启动
6 PT1
D809由1N4007改为FR107
2
6 PD3 +12V +12V_Normal
D807 D805 1 NP1 1
CY800 1 3 1
CY801 + EC805 68KΩ-2W-J(立式) C1034 2 +12V_PD3 +12V
R865 3 2
NP1 3
7 11 3
金属氧化膜电阻/68KΩ-2WS-J 卧式短脚 脚距15MM R882 7 12V
+ PEC6 PC7
贴片电阻22Ω-1/4W-J-1206 R881 贴片电容/1uF-25V-M-0603-X5R
电解电容-高频低阻/820uF-25V-M,Ф13*12*5,3000H,编带
R01 R02 电解电容-高频低阻/100uF-450V-M,Φ16*45*7.5,90度加长2涤纶电容/4700PF-400V-K,D=5,编带,直脚 2 PC8
贴片电阻/10Ω-1/4W-J-1206 2 NP2 PR3 PC5
贴片电阻22Ω-1/4W-J-1206 贴片电容/1uF-25V-M-0603-X5R
贴片电阻/10Ω-1/4W-J-1206 10R/1206 NB2
Y1电容/220PF-400V C1053跟公板BOM不对 10R/1206 8 NP2 4
Y1电容/220PF-400V 公板BOM 10uF/50 8 NB2 4 PR4 贴片电阻47Ω-1/4W-J-1206
D PC9 D
贴片电阻470KΩ-1/4W-F-1206 3 贴片电阻47Ω-1/4W-J-1206
3
D810
贴片电阻470KΩ-1/4W-F-1206 C1056 贴片电容0.1uF-50V-K-0603-X7R 贴片电容/2200PF-50V-K-0201-X7R
C1053 电解电容/10uF-50V-Z,Φ5*11*2.5,编带 11
11 PD15
4 3
D809 6 A K
R880 6 二极管-肖特基SR3200 3A/60A/200V/0.5V/DO27浮高5MM
Y1电容/100PF-250V-K-K脚/10MM 编带 LF801 R876 R878 + NP2 8
二极管-快恢复FR207 2A/1KV/1.3V/500NS/DO-15编26 12V 二极管-肖特基SR3200 3A/60A/200V/0.5V/DO27浮高5MM
共模电感/SYUC15-105MA-10mH-线径0.5mm 二极管-快恢复RS1G 1A/30A/400V/150NS/DO-214AC A K 24V
CY802 2 1 10 NP2
U807 贴片电阻/10Ω-1/4W-J-1206 10
FB7 NB1
5
穿心磁珠/10Ω-25%-3.5*6*0.8mm,编带52 PD16 PC14
5
5
VDD
3 10 + PEC7
RI 24V PR15 PR18
6 5 电解电容-高频低阻/220uF-35V-M,Φ10*12*5,3000H,编带 东阳光
PR2 GATE 5
PR16 PR17 瓷片电容-高压/ 470PF-1KV,D=5,编带
R883 R884 NC 4 1
CS 1
9
2
GND
FB 7
NC
NC
GND 贴片电阻/100Ω-1/4W-J-1206
9
贴片电阻/1MΩ-1/4W-F-1206 RT9 贴片电阻/100Ω-1/4W-J-1206
保护器件-热敏电阻 5Ω-7D 5A脚距7.5MM 短脚3.2MM
贴片电阻/100Ω-1/4W-J-1206
1
PQ1
9
贴片电阻/1MΩ-1/4W-F-1206
贴片电阻/100Ω-1/4W-J-1206
MOS高压N/MME70R380P 11A/700V/+-30V/TO-263 美格纳
R889 PQ3 NC/MOS高压N/MME70R380P 11A/700V/+-30V/TO-263 美格纳 5V Max@DTV(with out CI,USB,DVD,panel)490mA
贴片电阻/33Ω-1/8W-J-0805 R890
瓷片电容-高压/100PF-1KV,D=5,编带 5V Stb(with out ci card)23mA
R885 R888 贴片电阻1KΩ-1/10W-J-0603
Q811
CI card module max 200mA
贴片电容/100PF-50V-J-0402-NP0 +12V_Normal 工作频率477Khz占空比43%工作电流1.1A,实测电压5.16V,纹波100mV
C1 C1068 R891
三极管PNP/2N3906,-40V,-0.2A,0.2W,100,SOT-23 R892 C001 PU2
贴片电阻/1KΩ-1/8W-J-0805
X2电容/0.22uF-275V-K,D=10,立式,短脚 贴片电阻/10KΩ-1/16W-J-0402 IC-DCDC/TPS563201,3A,17V,SOT23-6,0.768V TI
CX1 PR25 NC/10nF/50V/X7R +12V_Normal
贴片电阻/22Ω-1/8W-J-0805
X2电容/0.22uF-275V-K,D=15,立式,短脚 贴片电阻/1KΩ-1/16W-J-0402
贴片电阻470Ω-1/10W-J-0603 R866 PC17 贴片电容/0.01uF-50V-K-0402-X7R
贴片电阻/1MΩ-1/4W-F-1206 R894 贴片电阻/36KΩ-1/16W-F-0402
金属氧化膜电阻/100KΩ-2W-J 卧式 贴片功率电感/4.7u H-5A/-10.7*10.5*4.3mm(带屏蔽) +5V_Normal
贴片电阻/1MΩ-1/4W-F-1206 贴片电阻/36KΩ-1/16W-F-0402
6
金属氧化膜电阻/0.33Ω-2W-J(卧式短脚/脚距20MM)
贴片电容/1000PF-50V-K-0402-X7R C1069 PFB2 PL1 +5V_Standby
BS
贴片电容/0.1uF-16V-K-0201-X7R
1
3
PR895 PR34 PR35 PR36 VIN 2 5Vstb 5Vstb
PU3 LX
RT1
PC25 贴片电容/0.22uF-16V-M-0402-X5R
PR27 TPS563201 CD94
PC20PC19 + PEC12
SOT23-6
2
PC30 PC24 PC28
PR37 PC26 5 +3.3V_Standby
GND
EN 4 PR1
保护器件-热敏电阻 5Ω-7D 5A脚距7.5MM 短脚3.2MM IC-MISC/EL817M(C)-F,OC,DIP-4,,EverLight 光耦 FB PR43 贴片电阻/10KΩ-1/16W-F-0402
C 保护器件-安规保险管/T3.15A-250V,方形塑封,不带套管,编带,立式 贴片电阻/1KΩ-1/16W-J-0402 C
PU4 贴片磁珠/10Ω-4A-0603
贴片电阻/10KΩ-1/16W-J-0402
PR6
PC27
贴片电阻/10KΩ-1/16W-F-0402
贴片电阻/100KΩ-1/16W-F-0402 贴片电容/10uF-6.3V-M-0603-X5R
Y1电容/1000PF-250V,K脚 PR40 PR41 电解电容-高频低阻/220uF-16V-Z,Φ6.3*11.5*2.5,编带黑色 OP_ON/OFF 3
IC-REG/TL431,TO-92,Taping 编带,永盛 贴片电容/1uF-25V-K-0603-X5R
贴片电容/1uF-25V-K-0603-X5R NC/贴片电容/33PF-50V-J-0402-NP0
贴片电阻/100KΩ-1/16W-F-0402
贴片电容/10uF-6.3V-M-0603-X5R PR9
NC/1000PF/50V/X7R PWR_ON/OFF 4 PQ2
F800
1
三极管NPN/2N3904/40V/0.2A/0.2W/100/SOT-23
Vout=0.768X(1+Rup/R down )
贴片电阻/100KΩ-1/16W-F-0402
贴片电阻/33KΩ-1/16W-F-0402
2
贴片电阻/39KΩ-1/16W-F-0402
磁环电感/39uH-K-φ12*r8*H4-线径0.7,铁硅铝,卧式
CN800 NC/10uH/3.8A
贴片电容1uF-50V-M-0805-X5R 非标 额定电流/工作电流4A/1.08A 二极管-肖特基SR3A0 3A/80A/100V/0.85V/DO27成型浮高
插座/2P-7.92-卧式-单列-高压
贴片电容1uF-50V-M-0805-X5R 非标 贴片电阻22Ω-1/4W-J-1206
瓷片电容-高压/1000PF-1KV,D=5,编带
NC/10-4A-0603
电解电容-高频低阻/220uF-35V-M,Φ10*12*5,3000H,编带 东阳光 PR44 PC29
IC-DRIVER_LB/OB3350CPA,1CH,LED,昂宝,SO8
额定电流/工作电流4A/1.08A
PEC11
+ PC22
PC23
穿心磁珠/10Ω-25%-3.5*6*0.8mm,编带52
PD14
MOS中压N/B15N10D,15A,100V,±20V,TO-252 ,BITEK
LED+ LED+ Vout=2×(PR45+PR47)/PR47
一般需要固定R826,只改PR47,
否则会影响到输出功率。
TO INVERTER
贴片电阻22Ω-1/4W-J-1206
贴片电容/1uF-25V-M-0603-X5R
贴片电容/1uF-25V-M-0603-X5R
PQ6 PR71 PEC8 + PC33
PR46
PU5 DRV TO252-DPAK 瓷片电容-高压/10nF-1KV,编带
贴片电阻/1KΩ-1/16W-J-0402
贴片电阻47Ω-1/10W-J-0603 PR45 电解电容-高频低阻/100uF-63V-M,Φ8*12*2.5,编带 黑色
PR48 贴片电阻/10KΩ-1/16W-F-0402
贴片电阻/10KΩ-1/16W-J-0402 PC31
+12V 1 8 ON/BK RD37 ON/BK
VIN PWM PR50 贴片电容/1000PF-50V-K-0402-X7R VBL_CTRL 4
B DRV 2 7 OVP 贴片电容/1000PF-50V-K-0402-X7R
OVP 贴片电阻/68KΩ-1/16W-F-0402 RD41 B
GATE OVP 贴片电阻/330KΩ-1/16W-F-0402
CD1 CD2 PR49
3 6 贴片电容/470PF-50V-K-0402-X7R 贴片电阻/1KΩ-1/16W-F-0402
GND CMP PC32 PC34 PCN4
贴片电阻/2.2KΩ-1/16W-F-0402 贴片电容/2.2uF-6.3V-M-0402-X5R
4 5 FB PR47
CS FB LED1 RD40
PR70
1 BL-ADJUST
2 BRI_ADJ 4
CS LED+
贴片电阻/1KΩ-1/16W-J-0402 3
PR51
贴片电阻/220Ω-1/16W-F-0402 插座/3P-2.0-立式-单列 CD46
PR52
贴片电容/1000PF-50V-K-0402-X7R
PC35 PR53
贴片电容/0.22uF-16V-M-0402-X5R PC36
贴片电阻0.3Ω-1/4W-J-1206 FB1 1, 用软排线时,RD75为NC,CD46为NC;
贴片电阻0.3Ω-1/4W-J-1206 PR55 贴片电阻2.2Ω-1/4W-J-1206
贴片电阻0.3Ω-1/4W-J-1206 PR57 贴片电阻1.5Ω-1/4W-J-1206 2, 用两PIN线:600MA时,RD75装0欧电阻,CD46为2.2μF,RD38为430R,QD5为NC;
PR56 贴片电阻1.5Ω-1/4W-J-1206
插座/4P-2.0-立式-单列
插座/2P-2.0-立式-单列 插座/2P-2.0-立式-单列
JP9 JP7 JP10 4
+5V_Standby 3
ON/BK 1 2
24V 1 +12V 1
BL-ADJUST 2 1
2 2 PR59 PR58
3
贴片电阻/15KΩ-1/16W-J-0402 贴片电阻/220KΩ-1/16W-J-0402
JP5 FB1 FB BL-ADJUST
老化端口 老化端口 老化端口
PR60
贴片电阻/220KΩ-1/16W-J-0402
A A
晨星软件研发(深圳)有限公司
Title
5 4 3 2 1
5 4 3 2 1
MARK
1.15V 3A for VDDC +12V_Normal
实测电流:Irms=800mA,Imax=2000mA。
H1 H2
IC-DCDC/TPS563208 +1.15V_VDDC
1
贴片电容/0.01uF-50V-K-0402-X7R 5 9 5 9
U101 811MA
贴片功率电感/2.2uH-2.5A-5.9*5.9*3.1mm,带屏蔽
6
C117
4 8 4 8
BS
3 L101
VIN 2 3 7 3 7
LX
C111
C116
563201 R134 贴片电容/33PF-50V-J-0402-NP0 2 6 2 6
D D
SOT23-6 贴片电容/10uF-6.3V-M-0603-X5R NC NC
R103 5 C122 C105C106 + 贴片电容/10uF-6.3V-M-0603-X5R
GND
EN 4
FB EC105
C126 电解电容-高频低阻/100uF-25V-Z,Φ6.3*7*2.5,编带 T1
1
R135
1
5 9
贴片电容10uF-50V-K-0402X7R
贴片电容10uF-50V-K-0402X7R 4 8
贴片电阻/100KΩ-1/16W-F-0402
贴片电阻/2.2KΩ-1/16W-F-0402
NC/贴片电容/0.1uF-16V-M-0402-X5R
贴片电阻/2.2KΩ-1/16W-F-0402 3 7
R136
贴片电阻/10KΩ-1/16W-F-0402
2 6
NC
Vout=0.768X(1+Rup/Rdown ) 结构限高,
只能在10MM下
H5 2P-46X42
H3
1
5 9
2
4 8
2
3 7
实测电流:Irms=386mA,Imax=700mA。 1.52V
LD21
1.52V
+1.5V_DDR 2 6
贴片功率电感/2.2uH-2A-4.5*4*4mm,不带屏蔽 NC
NC/33PF
H5主芯片散热片
C 4 3 C
VIN LX
SY8088B RD139
CD101 CD91
C123
R112 1 5
GND
贴片电阻/100KΩ-1/16W-F-0402 EN OUT/FB
贴片电阻/100KΩ-1/16W-F-0402
RD144
贴片电阻/51KΩ-1/16W-F-0402
贴片电容/10uF-6.3V-M-0402-X5R
贴片电阻/100KΩ-1/16W-F-0402
2
NC/贴片电容/100PF-50V-J-0402-NP0
NC/10uF/6.3V/X5R/0402 CD103
EN OUT/FB
RD145
贴片电阻/75KΩ-1/16W-F-0402
2
CD104 贴片电容/100PF-50V-J-0402-NP0
PANEL POWER
+12V_Normal RD56 贴片电阻/0Ω-1/8W-J-0805
Vpp=100mV
VCCLCDFN VCC-Panel
QD6
+5V_Normal RD59 NC/0R/0805 VCCLCDFN
R3 MOS-P/KO3407,-4.1A,-30V,±20V,SOT-23, ?KEXIN
贴片电阻/2.2KΩ-1/10W-F-0603
贴片电容/0.1uF-16V-M-0402-X5R
RD62
贴片电阻/270KΩ-1/16W-J-0402
RD65 RD66
C
QD7
A RD63 B A
C
QD8
RD64 4 B 工作电流: 冲击电流:
PANEL_ON/OFF +12V:2.06A
E
+12V:251.3mA
+5V:583mA +5V:1.41A
E
贴片电阻/4.7KΩ-1/16W-F-0402 三极管NPN/2N3904/40V/0.2A/0.2W/100/SOT-23
贴片电阻/100KΩ-1/16W-F-0402 贴片电阻/10KΩ-1/16W-F-0402
贴片电阻/10KΩ-1/16W-F-0402 三极管NPN/2N3904/40V/0.2A/0.2W/100/SOT-23
晨星软件研发(深圳)有限公司
Title
5 4 3 2 1
5 4 3 2 1
+3.3V_Standby
CORE POWER DDR3 POWER
AVDD_DDR_DATA
AVDD_DDR_CMD
AVDD_ETH VDDC VDDC R276
+1.5V_DDR AVDD_DDR_CMD AVDD_DDR_DATA AVDDL_DVI AVDD_MOD
VDDC +1.15V_VDDC AVDDL_DVI DVDD_DDR 47K
贴片电容/2.2uF-6.3V-M-0402-X5R DVDD_DDR
RXO0- 5
贴片电容/0.1uF-16V-M-0402-X5R PCM_PWR_CTL RXO0-
8 PCM_PWR_CTL RXO0+ 5
贴片电容/0.1uF-16V-M-0402-X5R RXO0+
RXO1-
UART_RX2
BRI_ADJ-PWM0
贴片电容/0.1uF-16V-M-0402-X5R C237 C249 C251 C252 C253 C259 贴片电容/10uF-6.3V-M-0603-X5R RXO1- 5
HDMI1_HPDIN
HDMI0_HPDIN
C236 C238 C239 C240 C241 C243 C244 C245 RXO1+
HDMI0_RX2P
HDMI0_RX1P
HDMI0_RX0P
HDMI0_RX2N
HDMI0_RX1N
HDMI0_RX0N
HDMI0_CLKN
HDMI1_SCL
HDMI1_SDA
HDMI0_CLKP
HDMI_CEC
贴片电容/0.1uF-16V-M-0402-X5R 贴片电容/2.2uF-6.3V-M-0402-X5R RXO1+ 5
System_RST
HDMI0_SDA
HDMI0_SCL
ARC
RXO2-
FLASH_WP
SPDIF-OUT
SC-HSYNC
C246 贴片电容/0.1uF-16V-M-0402-X5R 贴片电容/0.1uF-16V-M-0402-X5R IC 5
SPI_SDO#
SPI_CSN#
RXO2-
SPI_SCK#
UART_RX
UART_TX
RXO2+
SPI_SDI#
贴片电容/2.2uF-6.3V-M-0402-X5R 贴片电容/2.2uF-6.3V-M-0402-X5R +3.3V_Standby RXO2+ 5
CC0402 RXOC-
PWM1
贴片电容/0.1uF-16V-M-0402-X5R 贴片电容/0.1uF-16V-M-0402-X5R R258 NC/4.7K 5
KEY0
RXOC+ RXOC-
IRIN
贴片电容/10uF-6.3V-M-0603-X5R 贴片电容/2.2uF-6.3V-M-0402-X5R R257 NC/4.7K RXOC+ 5
此网络上一定不能用磁珠! RXO3-
2.2uF靠近供电网络最远端的pin RXO3- 5
此网络上一定不能用磁珠! UART_RX2 LNB_EN RXO3+
9 RXO3+ 5
LNB_EN
218
217
216
215
214
213
212
211
210
209
208
207
206
205
204
203
202
201
200
199
198
197
196
195
194
193
192
191
190
189
188
187
186
185
184
183
182
181
180
179
178
177
176
175
174
173
172
171
170
169
168
167
166
165
164
163
UART_TX2 LNB_SEL
LNB_SEL 9 RXE0-
LVDS
RXE0- 5
RXE0+
Standby Power 3.3V 5
GND
EPAD
RX2P_D
RX2N_D
RX1P_D
RX1N_D
RX0P_D
RX0N_D
RXCP_D
RXCN_D
VDDC/AVDDL_DVI
ARC
AVDD_5V
HOTPLUG_A
HOTPLUG_B
HOTPLUG_D
CEC
DDCDA_CLK
DDCDA_DAT
DDCDB_CLK
DDCDB_DAT
GND-EFUSE
TP
TN
RP
RN
AVDD_ETH
VDDIO_DRAM
VDDIO_DRAM
VDDIO_DATA
GND
VDDIO_DATA
AVDD_MOD
DVDD_DDR_DATA
SAR1
SAR0
DDCDD_SDA
DDCDD_CLK
MHL_DET
DDCA_CK
DDCA_DA
VDDC
SPI_DO/SPI-NAND_DO/NANAD_RBZ
SPI_CK/SPI-NAND_CK/NAND_ALE
SPI-NAND_WP/NAND_WP
SPI-NAND_HOLDN/NAND_WEZ
SPI_DI/SPI-NAND_DI/NAND_REZ
NAND_CLE
SPI_CS/SPI-NAND_CS/NAND_CEZ
VDDC
PWM1
PWM0
RESET
IRIN
GPIO0/SPDIF_OUT
GPIO2/RX2
RXE1- RXE0+
RXE1- 5
RXE1+ 5
RXE2- RXE1+
RXE2- 5
D RXE2+ D
AVDD_DMPLL RXE2+ 5
+3.3V_Standby RXEC- 5
+3.3V_Standby AVDD_ETH AVDD_MOD AVDD3P3_ADC RXEC+ RXEC-
RXEC+ 5
贴片磁珠/220Ω-500mA-0402 RXE3- 5
贴片电容/2.2uF-6.3V-M-0402-X5R RXE3-
FB211 HDMI1_CLKN 1 UART_TX 6 RXE3+ 5
贴片电容/0.1uF-16V-M-0402-X5R 贴片电容/0.1uF-16V-M-0402-X5R RXCN_B UART-TX RXE3+
C294 C292 C290 C295 C278 C279 C280
贴片电容/0.1uF-16V-M-0402-X5R 不能省掉!
HDMI1_CLKP
HDMI1_RX0N
2
3 RXCP_B AVDDL_MOD/VDDC
162
161 PWR_ON/OFF
VDDC OTHER UART_RX
贴片电容/0.1uF-16V-M-0402-X5R RX0N_B PWR_ON/OFF UART-RX 6
C293 HDMI1_RX0P 4 160 VBL_CTRL
贴片电容/0.1uF-16V-M-0402-X5R RX0P_B VBL_CTRL LCD_OP
HDMI1_RX1N 5 159 AMP-MUTE IP_S 0.1uF C258 LCD_OP 5
贴片电容/0.1uF-16V-M-0402-X5R RX1N_B GPIO18 IP-S 9
HDMI1_RX1P 6 158 PANEL_ON/OFF IM_S 0.1uF C257
贴片电容/0.1uF-16V-M-0402-X5R RX1P_B PANEL_ON/OFF IM-S 9
HDMI1_RX2N 7 157 RXO0- QP_S 0.1uF C256
HDMI1_RX2P 8 RX2N_B LVB0- 156 RXO0+ QM-S 9 PCM_RESET
RX2P_B LVB0+ QM_S 0.1uF C255 9 PCM_RESET 8
9 155 RXO1- QP-S PCM_IRQA_N
AVDD_MOD AVDD_MOD LVB1- PCM_IRQA_N 8
10 154 RXO1+ PCM_IOWR_N 8 PCMCIA
11 RXCN_A LVB1+ 153 PCM_OE_N PCM_IOWR_N
RXCP_A AVDD_MOD AVDD_MOD C265 C264 C261 C260 PCM_OE_N 8
12 152 RXO2- 22pF 22pF 22pF 22pF PCM_IORD_N 8
+3.3V_Standby AVDD_EAR33 AVDD_AU33 +3.3V_Standby AVDD_DADC 13 RX0N_A LVB2- 151 RXO2+ PCM_CE_N PCM_IORD_N
RX0P_A LVB2+ PCM_CE_N 8
14 150 RXOC- C260/C261/C264/C265靠近IC摆放 PCM_WE_N 8
贴片磁珠/220Ω-500mA-0402 贴片磁珠/220Ω-500mA-0402 15 RX1N_A LVBCLK- 149 RXOC+ PCM_CD_N PCM_WE_N
RX1P_A LVBCLK+ PCM_CD_N 8
FB209 16 148 RXO3- PCM_REG_N 8
FB207 17 RX2N_A LVB3- 147 RXO3+ IFAGC_S PCM_WAIT_N PCM_REG_N
贴片电容/0.1uF-16V-M-0402-X5R 贴片电容/0.1uF-16V-M-0402-X5R RX2P_A LVB3+ IFAGC_S 9 PCM_WAIT_N 8
不能省掉! C289 C288 不能省掉! VGA_HS 18 146 VIFP 9
HSYNC0 LVB4- VIFP
贴片电容/0.1uF-16V-M-0402-X5R C291 BIN0 19 145 VIFM 9
BIN0P LVB4+ VIFM
GIN0P 20 144 RXE0- IFAGC_T
VGA Port GIN0M 21 GIN0P LVA0- 143 RXE0+ DISEQC IFAGC_T 9
GIN0M LVA0+ DISEQC 9
RIN0 22 142 RXE1- PANEL_ON/OFF 3
VGA_VS 23 RIN0P LVA1- 141 RXE1+ PWR_ON/OFF PANEL_ON/OFF
VSYNC0 LVA1+ PWR_ON/OFF 2
AVDD3P3_ADC 24 140 RXE2- BRI_ADJ-PWM0 2
BIN1 25 AVDD3P3_ADC LVA2- 139 RXE2+ VBL_CTRL BRI_ADJ
BIN1P LVA2+ VBL_CTRL 2
GIN1P 26 138 RXEC-
GIN1P LVACLK-
+3.3V_Standby
RESET SCART Port
SAR1-->SC-HSYNC
GIN1M
RIN1
SC-VSYNC
BIN2
27
28
29
30
GIN1M
RIN1P
VSYNC1
MSD3663LS LVACLK+
LVA3-
LVA3+
137
136
135
134
RXEC+
RXE3-
RXE3+
MI2C-SCL
MI2C-SDA
AMP-MUTE
TUNER_SCL
TUNER_SDA
9
9
PCM_D[7:0]
SO HOLD# HDMI1_RX0P HDMI1-RX0N
49 EARPHONE_OUTR TS0_D1 115 TS0_D2 PCM_D1 TS1_D1 6
C135 HDMI1-RX0P
TS1_D[7:0]
4 5 SPI_DI AVDD_EAR33 AVDD33_EAR TS0_D2 HDMI1_RX1N
0.1uF(X7R) #F_WP 3 6 SPI_SCK TF4 TF5 QP_S 50 114 TS0_D3 PCM_D2 TS1_D2 HDMI1-RX1N 6
WP# SCK #F_WP 3 6 SPI_SCK QP_S TS0_D3 HDMI1_RX1P
TF3 TF1 TF6 QM_S 51 113 TS0_D4 PCM_D3 TS1_D3 HDMI1-RX1P 6 HDMI
SPI_DO 2 7 TP2 QM_S TS0_D4 HDMI1_RX2N
PCM_RESET/EJ_RSTZ
GPIO50/I2S_OUT_BCK
4 5 SPI_DI TF2 TP TF7 52 112 TS0_D5 PCM_D4 TS1_D4 HDMI1-RX2N 6
GPIO48/I2S OUT SD
53 111 6
PCM_D7/EJ_TRSTN
TF1 TF8 IP_S TS0_D6 PCM_D5 TS1_D5 HDMI1-RX2P
PCM_A12/EJ_DINT
IP_S TS0_D6 HDMI1_CLKN
AVDD3P3_DMPLL
IM_S 54 110 TS0_D7 PCM_D6 TS1_D6 6
PCM_D5/EJ_TDO
HDMI1-CLKN
PCM_A6/EJ_TMS
PCM_D4/EJ_TCK
GPIO49/DISEQC
HDMI1_CLKP
PCM_D6/EJ_TDI
IM_S TS0_D7 109 TS0_VLD PCM_D7 TS1_D7 6
MX25L6405DMI-12G(SOP-8) HDMI1-CLKP
PCM_IOWR_N
HDMI1_SCL
PCM_WAIT_N
PCM_IORD_N
PCM_IRQA_N
TSO_VLD
PCM_REG_N
TS1_CLK 6
VDDIO_CMD
HDMI1-SCL
GPIO46/TX2
AVDD_MOD
PCM_WE_N
8
PCM_CD_N
PCM_OE_N
HDMI1_SDA
PCM_CE_N
TS1_CLK
TS0_SYNC
TS1_VLD HDMI1-SDA 6
PCM_A14
PCM_A13
PCM_A11
PCM_A10
8 HDMI1_HPDIN
TS0_CLK
IFAGC_S
TS1_VLD
IFAGC_T
PCM_D0
PCM_D1
PCM_D2
PCM_D3
PCM_A9
PCM_A8
PCM_A7
PCM_A5
PCM_A4
PCM_A3
PCM_A2
PCM_A1
PCM_A0
PCM_A0 TS1_SYNC HDMI1-HPDIN 6
GPIO44
GPIO45
+5V_Standby TS1_SYNC 8
VDDC
VDDC
XOUT
PCM_A1
IM_T
HDMI_CEC
IP_T
HDMI-CEC 6
XIN
PCM_A2
Crystal C285
PCM_A3
TS0_D[7:0] 8
U201MSD3563LS PCM_A4 TS0_D0
2.2uF/NC 根据实际电源
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
PCM_A5 TS0_D1
TS0_D[7:0]
上电时序调整
C1 PCM_A6 TS0_D2
PCM_A[14:0]
PCM_A7 TS0_D3
PCM_WAIT_N
PCM_IRQA_N
PCM_IORD_N
PCM_IOWR_N
PCM_REG_N
晶振/24MHz-11P-20PPM,49S-DIP
PCM_RESET
R283 1K/NC System_RST
PCM_PWR_CTL
PCM_WE_N
PCM_A8 TS0_D4
PCM_CD_N
PCM_OE_N
PCM_CE_N
TS0_SYNC
MI2C-SDA
MI2C-SCL
PCM_A14
PCM_A13
PCM_A12
PCM_A11
PCM_A10
LCD_OP
HP_DET
PCM_A9 TS0_D5
TS0_CLK
UART_TX2
PCM_D0
PCM_D1
PCM_D2
PCM_D3
PCM_D4
PCM_D5
PCM_D6
PCM_D7
IFAGC-S
PCM_A9
PCM_A8
PCM_A7
PCM_A6
PCM_A5
PCM_A4
PCM_A3
PCM_A2
PCM_A1
PCM_A0
IFAGC-T
XTALO C281 15pF
3
LED-R
XTALO
DISEQC
PCM_A10 TS0_D6
XTALI
VIFM
VIFP
D202 PCM_A11 TS0_D7
1
Y201 R284
3 R248 PCM_A12 TS0_CLK 8
100K/NC TS0_CLK
PCM_A13 TS0_VLD 8
0k TS0_VLD
AVDD_DDR_CMD
VDDC
AVDD_MOD
二极管-肖特基/BAV99 215MA/1A/85V/1.25V/SOT-23 PCM_A14 TS0_SYNC
TS0_SYNC 8
C2
2
8 PCM_A[14:0]
1
晶体XTALI预留给tuner共用的option
RD44
C41 贴片电容/10uF-6.3V-M-0603-X5R BIN0 C204 47nF R287 33R
VGA-R 6 VGA
2'b01 Boot from SPI_NOR Flash 贴片电阻/4.7KΩ-1/16W -J-0402 GIN0P 47nF R288 33R
VGA-B 6
RD43
C205 VGA-G 6
2'b10 Boot from NAND 贴片电阻/47KΩ-1/16W -F-0402 GIN0M C206 47nF R289 68R
B SC-HSYNC B
SCART-FS 6
+3.3V_Standby AMP-INR SC-VSYNC 6
AMP-AUOUTR 7 SCART-FB
贴片电阻/4.7KΩ-1/16W -J-0402 RIN1 C207 47nF R290 33R 6 SCART
贴片电阻/1KΩ-1/16W -F-0402 SCART-R
R250 PWM1 6 BIN1 C208 47nF R291 33R 6
SCART-B
R255 NC/4.7K 5 GIN1P C209 47nF R292 33R 6
IRIN RD52 SCART-G
R254 NC/4.7K 4 GIN1M C210 47nF R293 68R
R251 BRI_ADJ-PWM0 3
贴片电阻/4.7KΩ-1/16W -J-0402 LED_R
KEY0 RD49 2 AMP-AUOUTL
1 AMP-INL 7
RIN2 C211 47nF R294 33R
CD47
CD48
贴片电容/1000PF-50V-J-0402-NP0 贴片电阻/1KΩ-1/16W -F-0402
BIN2 C212 47nF R295 33R
YPBPR-PR 6 YPBPR
CD52
YPBPR-PB 6
33pF/50V/NPO CN201 GIN2P C213 47nF R296 33R
YPBPR-Y 6
上电时要确保不能受外围电路的影响 GIN2M C214 47nF R297 68R
贴片电容/1000PF-50V-K-0402-X7R SIDE_CVBS 6
AV-LINEOUTR 6
C231 AV-AUOUTR0
CD52 near IC
SC-CVBS-IN C215 47nF R298 33R SCART AV IN
SPDIF OUT IF AGC LED 贴片电容/1000PF-50V-K-0402-X7R
VCOM0 C217 47nF R300 68R
SCART-AV-IN 6
AV-LINEOUTL 6
AV-AUOUTL0 CVBS_OUT0 6
CVBS_OUT
A A
晨星软件研发(深圳)有限公司
Title
LVDS CONNECTOR
2 1
TOAP RXO0+ 4 GND GND 3 RXO0- TOAN
D
TOBP RXO1+ 6 RO0+ RO0- 5 RXO1- TOBN D
TOCP RXO2+ 8 RO1+ RO1- 7 RXO2- TOCN
RXOC+ 10 RO2+ RO2- 9 RXOC-
TODP RXO3+ 12 ROC+ ROC- 11 RXO3- TODN
RO3+ RO3-
14 13 +3.3V_Normal
TEAP RXE0+ 16 GND GND 15 RXE0- TEAN
TEBP RXE1+ 18 RE0+ RE0- 17 RXE1- TEBN
TECP RXE2+ 20 RE1+ RE1- 19 RXE2- TECN
RXEC+ 22 RE2+ RE2- 21 RXEC- R256
TEDP RXE3+ 24 REC+ REC- 23 RXE3- TEDN
RE3+ RE3- 贴片电阻/1KΩ-1/16W-F-0402
VCC-Panel 26 25 LCD_OP
28 GND GND 27 LCD_OP
30 VCCLCDOP 29 VCC-Panel
VCC VCC R268
NC
C C
R269
NC/0R J1
插座/2*15P-2.0-立式-双列-带卡扣
RXO0- 4
RXO0+ RXO0- RXE0-
4 RXE0- 4
B RXO1- RXO0+ RXE0+ B
4 RXE0+ 4
RXO1+ RXO1- RXE1-
4 RXE1- 4
RXO2- RXO1+ RXE1+
4 RXE1+ 4
RXO2+ RXO2- RXE2-
4 RXE2- 4
RXOC- RXO2+ RXE2+
4 RXE2+ 4
RXOC+ RXOC- RXEC-
4 RXEC- 4
RXO3- RXOC+ RXEC+
4 RXEC+ 4
RXO3+ RXO3- RXE3-
4 RXE3- 4
RXO3+ RXE3+
RXE3+ 4
LCD_OP 4
LCD_OP
晨星软件研发(深圳)有限公司
A A
Title
6
21 DATA2+ HDMI0-RX2N 4 YIN 8 YIN 1 OTG_DM
2 RX1B1P D539 YPbPr-Y 4 4
DATA2 SHIELD HDMI0-RX1P 4 4 2 USB0_DM
3 RX1B2N RX1B1N 7 PBIN 3
DATA2- HDMI0-RX1N 4 YPbPr-PB 4 OTG_DP 贴片电容/10uF-6.3V-M-0603-X5R
4 RX1B1P RX1B0P 3 45 USB0_DP 4
DATA1+ HDMI0-RX0P 4 ESD
5 RX1B0N 2 PRIN
DATA1 SHIELD HDMI0-RX0N 4 YPbPr-PR 4
6 RX1B1N RX1BCLKP PBIN 6
DAT1A- HDMI0-CLKP 4 USB座/USB2.0-A,母座,卧式,13.8mm,黑芯,插件
7 RX1B0P RX1BCLKN 5
DATA0+ HDMI0-CLKN 4
23 8 DDC1BSCL 1
RD113
RD114
RD115
23DATA0 SHIELD HDMI0-SCL 4 NC/USB-101B/LI
9 RX1B0N DDC1BSDA
DATA0- HDMI0-SDA 4 贴片电阻/75Ω-1/16W-F-0402
10
10 RX1BCLKP
CLK+ 5V_HDMI0 贴片电阻/75Ω-1/16W-F-0402
11 内部电路已经有上拉电阻。 PRIN
CLK SHIELD 12 RX1BCLKN HDMI0/5V 贴片电阻/75Ω-1/16W-F-0402
CLK-
22
22 CEC
13
14
HDMI_CEC
HDMI_ARC
CLOSE TO IC
NC RD102
15 DDC1BSCL
SCL 16 DDC1BSDA 5V_HDMI0 HDMI_ARC CD57 HDMI-ARC
HDMI-ARC 4
SDA 17 RD101 RD104
DDC/CEC GND 18 HDMI0/5V 贴片电容/2.2uF-6.3V-M-0402-X5R
20 +5V POWER 19 HOTPLUG_1 RD105
D 20 HOT PLUG HOTPLUG_1 贴片电阻/22KΩ-1/16W-F-0402 D
贴片电阻/22KΩ-1/16W-F-0402
HDMI座/母座,单层卧式,无耳扣,贴片,编带
8 6 4 2
7 5 3 1
AV-RIN 4
4
HDMI2 5
SIDE_AULIN
AV-LIN 4
7
CD61
贴片电阻/0Ω-1/16W-J-0402/NC 贴片电容/1000PF-50V-K-0402-X7R
J14 J15 贴片电阻/0Ω-1/16W-J-0402/NC 耳机座/φ3.5,5P,四节15,孔心高3,不带检测,黑色,卧插/堵孔
HDMI1_RX2P HDMI1-RX2P
1 HDMI1_RX2P RD73 HDMI1-RX2P 4
DATA2+ HDMI1_RX2N HDMI1-RX2N
2 GSDA HDMI1-RX2N 4
DATA2 SHIELD HDMI1_RX1P HDMI1-RX1P
3 HDMI1_RX2N HDMI1-RX1P 4
DATA2- RD75 HDMI1_RX1N HDMI1-RX1N 4
4 HDMI1_RX1P HDMI1-RX1N 14mm
DATA1+ HDMI1_RX0P HDMI1-RX0P
5 HDMI1-RX0P 4
DATA1 SHIELD HDMI1_RX0N HDMI1-RX0N
6 HDMI1_RX1N HDMI1-RX0N 4
DAT1A- HDMI1_CLKP HDMI1-CLKP
7 HDMI1_RX0P HDMI1-CLKP 4 AV转接线
DATA0+ HDMI1_CLKN HDMI1-CLKN
8 HDMI1-CLKN 4
DATA0 SHIELD HDMI1-DDC-SCL (海尔线序)
9 HDMI1_RX0N HDMI1-SCL 4 3.5mm四级插头转RCA母头
DATA0- HDMI1-DDC-SDA
10 HDMI1_CLKP HDMI1-SDA 4
CLK+ 11
CLK SHIELD 贴片电阻/0Ω-1/16W-J-0402/NC
12 HDMI1_CLKN 5V_HDMI1
20 CLK- 13 HDMI_CEC HDMI1/5V 1-2-3-4=黄-红-白-地
RD74
21 GND1 CEC 14 GSCL RD110
22 GND2 NC 15 HDMI1-DDC-SCL (P/N: 30430701802)
23 GND3 SCL 16 HDMI1-DDC-SDA 5V_HDMI1
GND3 SDA RD103 RD109
17
DDC/CEC GND 18 HDMI1/5V
+5V POWER RD108
19 HDMI1-HPD
HOT PLUG HDMI1-HPD 贴片电阻/22KΩ-1/16W-F-0402
贴片电阻/22KΩ-1/16W-F-0402
HDMI座/母座,单层卧式,无耳扣,贴片,编带
NC/HDMI-L QD12
HDMI1-HPDIN RD107 4
贴片电阻/10KΩ-1/16W-F-0402
三极管NPN/2N3904/40V/0.2A/0.2W/100/SOT-23
贴片电阻/1KΩ-1/16W-F-0402
贴片电阻/4.7KΩ-1/16W-J-0402
16
J410
15 GSCL
VGA INPUT 贴片电阻/100Ω-1/16W-J-0402
贴片电阻/100Ω-1/16W-J-0402
SPDIF Output 耳机座/φ3.5,5P,四节15,孔心高3,不带检测,黑色,卧插/堵孔
J3
5
10 LD12 贴片磁珠/11Ω-500mA-0402
RD71 SPDIF_OUT RD69 OPTICAL SPDIF 2 J33
14 IVS VSYNC SPDIF_OUT 4 S
VGA-VSYNC 4 1
4 HSYNC G
C VGA-HSYNC 4 贴片电阻/33Ω-1/16W-J-0402 C
9 RD72 CD54
13 IHS C558 RD70 贴片电容/33PF-50V-J-0402-NP0 SPDIF 1 2
J411 3 GBLU VGAB
VGA-B 4 Closed to IC 贴片电阻/75Ω-1/16W-F-0402
8
12 GSDA NC/SPDIFOUT-背出
2 GGRN VGAG 贴片电容/33PF-50V-J-0402-NP0
VGA-G 4
7
NC/VGA/LI
11
1 GRED VGAR
VGA-R 4
6 +5V_Standby
贴片电阻/10KΩ-1/16W-F-0402
贴片电阻/10KΩ-1/16W-F-0402
贴片电阻/75Ω-1/16W-F-0402
贴片电阻/75Ω-1/16W-F-0402
贴片电阻/75Ω-1/16W-F-0402
RD79
RD80
RD81
RD82
RD83
PC_DB15HD_MIDDLE
17
RD94 贴片电阻/100Ω-1/16W-J-0402
Close to Mstar IC 光纤端子
GSDA UART-TX UART-TX 4
RD95 贴片电阻/100Ω-1/16W-J-0402
GSCL UART-RX NC/RCA-5P-SPDIF-立式 0R/0402
UART-RX 4
R57 SPDIF 2
SPDIF 2 VCC
VCC 4
4 +5V_Normal M1
M1 OPTICAL 1
1 Vin
Vin 5
5 M2
M2 3
OPTICAL 3 GND
GND
CN50
CN51 光纤座/DQT-012,9.55*8.1,黑色,带遮挡片,卧插
带光纤时,RD70,LD12,J3不贴,RD69改为0R
SCART / AV OUT
J401 L401
21
20 AV1-V AV1-V
贴片磁珠/11Ω-500mA-0402
SCART-AV-IN 4
AUDIO_OUTPUT R130
19 VOUT
18
贴片电阻/0KΩ-1/16W-F-0402
17 R402
C401 +12V_Normal
16 SC1_FB SCART-FB 4 待机功率降低0.05W
15 Pr 贴片电容/100PF-50V-J-0402-NP0
14 贴片电阻/75Ω-1/16W-F-0402
贴片电阻/4.7KΩ-1/16W-J-0402
13 C115 贴片电容/1uF-25V-M-0603-X5R
贴片电容/0.47uF-10V-M-0201-X5R
12 R401
11 Y 贴片电阻/75Ω-1/16W-F-0402 R114
10
B 9 贴片电阻/10KΩ-1/16W-F-0402 C177
贴片电容/0.47uF-10V-M-0201-X5R
B
8 SC1_FSO AV1-L R404 贴片电阻/10KΩ-1/16W-F-0402 AV-LOUT
SCART-FS 4 SCART-LIN 4
7 Pb
6 AV1-L R403 R117 贴片电阻/47KΩ-1/16W-F-0402
5 R405 R406 C402 C179
SC1_FSO Keep AGND trace with signal R116
C
4 贴片电阻/2.7KΩ-1/16W-F-0402 贴片电阻/10KΩ-1/16W-F-0402 C415 Q8 R119 C180 贴片电容/0.47uF-10V-M-0201-X5R
3 AV-LOUT 0-2v: TV Mode 贴片电容/100PF-50V-J-0201-NP0 B AV-AUOUTL0
2 AV1-R 5-8v: 16:9 AV Keep spacing for L/R C186 AV-AUOUTL0 4
1 AV-ROUT 贴片电容/0.47uF-10V-M-0201-X5R
9.5-12v: 4:3 AV
E
贴片电阻/10KΩ-1/16W-F-0402
25
24
R416
R417
R128 贴片电阻/47KΩ-1/16W-F-0402
6 AV1-L R127
C
5 Q9 R131 C185
4 VOUT 4
3 AV-LOUT
CVBS_OUT
CLOSE TO IC B
C184
AV-AUOUTR0
AV-AUOUTR0 4
贴片电阻/75Ω-1/16W-F-0402
贴片电阻/75Ω-1/16W-F-0402
贴片电阻/75Ω-1/16W-F-0402
2 AV1-R 贴片电容/0.47uF-10V-M-0201-X5R
E
24
SCART座/卧式,单层,不带螺丝孔,带定位柱 三极管NPN/2N3904/40V/0.2A/0.2W/100/SOT-23
贴片电阻/68Ω-1/16W-F-0402
贴片电阻/8.2KΩ-1/16W-F-0402
R129
贴片电阻/0KΩ-1/16W-F-0402
A A
晨星软件研发(深圳)有限公司
Title
9108/3113(3110)/2113
AMP-INL AL+ +12VAMP
AMP-INL 4,7
CD10
AMP-INR AMP-INR 4,7 AR+
UD3
9108/TPA3113D2
靠近U30的供电针脚pin28。
MUTE MUTE# 1 28 贴片电容/1uF-25V-M-0603-X5R
SD PVCCL 电解电容-高频低阻/220uF-16V-Z,Φ6.3*11.5*2.5,编带黑色
+ CD11
2 27 贴片电容/0.22uF-16V-M-0402-X5R
贴片电容/0.1uF-16V-M-0201-X5R FAULT PVCCL
D
贴片电容/0.22uF-16V-M-0402-X5R D
贴片电容/0.1uF-16V-M-0201-X5RAL+ C601 AMP1_L+3 26 贴片电容/0.22uF-16V-M-0402-X5R
LINP BSPL CD16 LD5 33UH LOUT+
贴片电阻/10Ω-1/16W-J-0402 LOUT#
CD15 4 25 CD20
LINN OUTPL L2
贴片电容/1uF-25V-M-0603-X5R
+12VAMP NC/10-4A-0603 贴片电容/1uF-25V-M-0603-X5R
贴片电容/1uF-25V-M-0402-X5R GAIN0 5 24 LD14
GAIN0 PGND 贴片电容/1uF-25V-M-0603-X5R
RD12
RD1810R/0603/NC CD22
NC/600-2A-0805 L3 SPEAKER
贴片电阻/10KΩ-1/16W-F-0402 GAIN1 6 23
GAIN1 OUTNL NC/10-4A-0603
LOUT- ROUT+
贴片电阻/10KΩ-1/16W-F-0402 CD14
CD23 7 22 33UH ROUT- 1
AVCC BSNL CD24 LD7
贴片电容/1uF-25V-M-0402-X5R LOUT- 2
+12VAMP LD3 +12V_Normal 8 21 NC/600-2A-0805 LD13 LOUT+ 3
贴片电容/0.1uF-16V-M-0201-X5R AGND BSNR CD26 LD8 33UH ROUT- 4
贴片电容/0.1uF-16V-M-0201-X5R CD27贴片电容/1uF-25V-M-0603-X5R
9 20 CD28
贴片磁珠/10Ω-4A-0603 CD17 GVDD OUTNR CN601
RD20 贴片电容/1uF-25V-M-0603-X5R
L4
RD21 10 19 NC/10-4A-0603
CD29 PLIMIT PGND LD11
NC/600-2A-0805 CD32
贴片电容/1uF-25V-M-0603-X5R
CD31 11 18
CD18 RINN OUTPR L6 NC/10-4A-0603 贴片电容/1uF-25V-M-0603-X5R
ROUT# ROUT+
AR+ C602 12
AMP1_R+ 17 +3.3V_Normal
RINP BSPR LD9 33UH
贴片电容/1uF-25V-M-0603-X5R CD33
13 16
贴片电容/0.22uF-16V-M-0402-X5R RD22 RD23
NC PVCCR +12VAMP LD10
NC/10K GAIN0贴片电阻/10KΩ-1/16W-F-0402
GND
14 15 NC/600-2A-0805
PBTL PVCCR RD25
GAIN1
CD21 RD24 NC/10K
29
贴片电阻/10KΩ-1/16W-F-0402
为了软件的声音曲线一致: 1
当位号UD3器件为 TDA3113 和 TDA2113 时,RD21=10K, 靠近U30的供电针脚pin15。
当位号UD3器件为 9108 时,RD21为NC。 JD1
FOR 3113 贴片电容/1uF-25V-M-0603-X5R
C C
MUTE +12VAMP
Head Phone FB6 贴片磁珠/220Ω-500mA-0402
EC901
Control
RD4增加待机功率0.03W,
AMP-INL 4,7
电解电容/47uF-16V-Z,Φ5*5*2.5,编带 CD74
PH_L
J603
耳机座/Φ3.5,5P,三节,孔心高2.5,带检测,黑色,卧插
10K改为47K可以减小 RD4 1
贴片电容/0.047uF-25V-M-0201-X5R
待机功率-20131115 贴片电阻/10KΩ-1/16W-F-0402 PH_R 2
WITH EARPHONE 3
MUTE HP_DET 4
HP_DET
FB8 贴片磁珠/220Ω-500mA-0402 PH_L 5
C
EC902
AMP_MUTE 4B WITHOUT AMP-INR 4,7 PH_R
RD9
需要注意右声音是否会影响到MUTE的控制, 电解电容/47uF-16V-Z,Φ5*5*2.5,编带 CD75
E
OFF
及声音曲线和频响。 +3.3V_Normal 贴片电容/0.047uF-25V-M-0201-X5R
CD78
RD129 RD118 贴片电阻/47KΩ-1/16W-F-0402
ON
Title
QD3
C
QD1 B
RD10
4.7K 3906 RD8 270K MSD3663LS
3904 Size Document Number Rev
CD8
Custom
<Amplify page> 1.0
E
A A
5 4 3 2 1
5 4 3 2 1
3
TS1_D7 56 MDI6 A12 22 PCM_A7 Q1201
TS0_CLK 57 MDI7 A7 23 PCM_A6 R1205 10K 4 1 3904
MOCLK A6 24 PCM_PWR_CTL
C PCM_RESET 58 PCM_A5 C
PCM_WAIT_N 59 RESET A5 25 PCM_A4
2
60 WAIT# A4 26 PCM_A3
PCM_REG_N 61 INPACK A3 27 PCM_A2
TS0_VLD 62 REG# A2 28 PCM_A1
TS0_SYNC 63 MOVAL A1 29 PCM_A0
TS0_D0 64 MOSTART A0 30 PCM_D0
TS0_D1 65 MDO0 D0 31 PCM_D1
TS0_D2 66 MDO1 D1 32 PCM_D2
PCM_CD2_N 67 MDO2 D2 33
CARD DETECT
GND
GND
GND
GND
68 CD2# WP 34
GND GND
+5V_Normal
72
71
70
69
A A
Title
MSD3663LS
Size Document Number Rev
Custom <PCMCIA page> 1.0
5 4 3 2 1
5 4 3 2 1
贴片电容/0.1uF-25V-M-0402-X5R
贴片电感/39nH-200mA-0402-J,铁氧体叠层 I2C Interface Filter
3.3V_TUNER 贴片电容/0.022uF-25V-M-0402-X5R
3.3V_TUNER
贴片电容/470PF-50V-K-0402-X7R 贴片电容/0.022uF-25V-M-0402-X5R
贴片电容/120PF-50V-K-0402-X7R 贴片电感-高频/270nH-100mA-0402-J,陶瓷叠层,顺络 SDCL1005CR27JTDF
J5 贴片电感-高频/6.8nH-300mA-0402-J,陶瓷叠层,顺络 SDCL1005C6N8JTDF
贴片电感-高频/270nH-100mA-0402-J,陶瓷叠层,顺络
C6 SDCL1005CR27JTDF RT12
RT11
10 CT1 贴片电阻/4.7KΩ-1/16W-F-0402
贴片电阻/4.7KΩ-1/16W-F-0402
9
8
1 75 ohm line L25
DT1 贴片电阻/330Ω-1/16W-J-0402
C5 二极管-肖特基/BAV99 215MA/1A/85V/1.25V/SOT-23 TU_SCL RT2 SCL-T
7 TUNER_SCL 4
RFIN RFIN L19 TU_SDA RT10 SDA-T 4
6 5 L17 TUNER_SDA
4
3
2
CT5
贴片电阻/330Ω-1/16W-J-0402
LT3
LT4
CT4 LT1 CT2 CT3
CT6
CT7
LT2 贴片电容/68PF-50V-J-0402-NP0
TUNER_GND Close R842 Addr 0xF6
24
23
22
21
20
19
UD16 贴片电容/68PF-50V-J-0402-NP0
CT10 LT5
AVDD
TFH
TFL
DET2
DET3
NC
CT8 3.3V_TUNER - filter noise from demod side
NC/1.8pF
B
25
高频头屏蔽盖(欧规)/LD3910-WJ38-01 贴片电容/120PF-50V-K-0402-X7R 贴片磁珠/1KΩ-150mA-0402 GND CT9 贴片电容/1000PF-50V-K-0402-X7R
1 18
CT4的选取:
RFIN AVDD IFAGC Circuit
LT6 2 17 VOP MSTAR方案,AGC采用电流型输出,RT3的不易过大。
D 1.内置隔离器时,CT4=0R LT7 RF_bias VOP 其他方案,可采用参考设计要求的10K. D
2.不带内置隔离时,CT4=470PF 贴片电感-高频/270nH-100mA-0402-J,陶瓷叠层,顺络 SDCL1005CR27JTDF 贴片磁珠/1KΩ-150mA-0402 3 16 VON
TF1 IC-RF/R842,Rafael,QFN-24
VON
LT8 4 15 VAGC VAGC RT3 贴片电阻/100Ω-1/16W-J-0402
TF2 VAGC IFAGC_T 4
CT19 5 14 CT18 贴片电容/0.1uF-25V-M-0402-X5R
DECT1 VAGC2
贴片电容/0.047uF-25V-M-0402-X5R 6 13
SCL XTAL_O RT4 NC
贴片电感-高频/180nH-100mA-0402-J,陶瓷叠层,顺络 SDCL1005CR18JTDF
XTAL_I
2
DVDD
AVDD
DVSS
Application
SDA
XT1
CP
DTMB (S11<-8) TU_SCL
贴片晶振/24MHz-11P-20PPM-49SMD(-20~+85°C/晶峰) - R103 and R106 are related to Demod side's
10
11
12
1
L17=GZ1005D102CTF, L19=27nH,C5=470pF, L25=6.8nH, C8=L23=C6=NC, L22=0R TU_SDA IFAGC design. Sometime need to fine tune
for different Demod.
- Following IFAGC TBD table is common
ATV only, ATSC (S11>-8) suggestion.
L17=270nH, L19=39nH,C5=470pF, L25=0R, C8=L23=C6=NC, L22=0R
CT20 RT5
Hybrid ( with S1 filter for EN55020) 3.3V_TUNER
L17=L23=L22=270nH, L19=39nH,C5=100pF, L25=6n8H, C8=C6=120pF 贴片电容/0.1uF-25V-M-0402-X5R IFAGC TBD table
贴片电容/330PF-50V-K-0402-X7R
CT23
CT21 CT22 贴片电阻/1.8KΩ-1/16W-F-0402 Open drain R103=100R
贴片电容/0.1uF-25V-M-0201-X5R
贴片电容/6800PF-50V-K-0201-X7R Push Pull R103=10KR
Bead (L21):
1k@100M &
400ohm@400M,300mA
靠近silicon tuner 摆放
贴片电容/1uF-6.3V-K-0402-X5R
Recommend to reserve R106, R110, R109
(1) +VDD3V input voltage tolerance must be under +-5% to filter noise from demod side. IF trace shielding by GND
(2) +VDD3V input ripple must be under 30mVpp
(3) Using LDO for +VDD3V is recommended
Close Tuner
C196
0.47uF/6.3V/X5R C193 0.1uF/16V/X7R
T3.3V C194 0.47uF/6.3V/X5R
J4
VCC_LNBA C195 1nF/50V/X7R 3P
1
2
3
C181
NC
1 2
21
20
19
18
17
16
+12V_Normal
TY1 C282 33pF
EPAD
VCC
VCC
GND
REGCAP
CP
4 12 C45 + RT5047
U1 R21 100R TUNER_SCL
RFAGC SCL C3 D2 SS24 2 7 R9 NC/4.7K
5 11 220uF/16V BST COMP +3.3V_Normal
2
GND
22pF 22pF
RXQN
RXQP
C192
RXIN
RXIP
VCC
102
1 2
1
9
C48 + C49
6
10
T3.3V
100uF/25V 0.1uF/25V VCC_LNBA
2
QM-S 4
IF_AGC_S
TL1 C44
140mA C46 C254 2 1 104 QP-S 4
1
1
A A
晨星软件研发(深圳)有限公司
Title
5 4 3 2 1
7. Electrical parts
7-1.Block D iagram
7. Electrical parts
7-1.Block D iagram
Service Manual
Model No.:
3
4 2
1
NO.Name
1 Connection Wire(For Speaker)
2 Connection Wire(Power For Panel)
3 LVDS Wire
4 Connection Wire(For Remote and Keyboard)
- 36 -
Service Manual
Model No.:
- 36 -
TV OPERATION
3. SOUND MENU
The third item of the MENU is the SOUND NOTE:
MENU. Restore factory default will clear all the programs
You can adjust the sound effect here such as and Reset all the settings to default value.
treble, bass, balance etc.
Press ▼▲ to move, press OK button to confirm, 6. USB FUNCTION
and press◀▶ to adjust. You must enter the Source menu first,then choice the
USB and press OK button,the USB menu will appear.
Sound Mode
CHANNEL
Standard Music Movie Sports User Input Source
PICTURE Balance
Auto Volume
TV
SOUND Surround Sound
TIME YPBPR
OPTION PC
MENU Back Move OK OK
HDMI1
Note: HDMI2
Auto volume: only available when the input
VIDEO
signal volume is too large or distortion.
OPTION
USB2.0 EXIT Back Move OK Select
NOTE: Please make sure that the USB device have plugged in
Within 15 minutes there is no signal, the TV the slot. There are four type media item can be selected,
will auto sleep. such as photo, music, Movie and text. Select the type
Once you power off the TV set by AC, the clock time media item by pressing◀▶, press OK button to enter
will be reset. the disk selection menu.
5. OPTION MENU In the movie mode, when you use FB, FF function, The
The fifth item of the MENU is the OPTION MENU. audio may be pause in several seconds to synchronize
You can adjust the OSD language, Restore factory the audio signal and video signal.
default, Blue Screen or OSD Blend. In text mode, press to make page up and page down.
CHANNEL
OSD Language NOTE:
English When the USB device isn't supported, it may be that the
PICTURE Restore Factory Default power of the USB device isn't enough.
Blue Screen
SOUND HDMI CEC
TIME
OPTION
- 37 -
TV OPERATION
Haier Innovation Life Press ◀▶ to select the function icon, press OK button to
confirm the function.
Press ▼ or EXIT button to exit the control bar.
NOTE:
return
Return C
You can adjust the audio track, subtitle, or program in
the Info menu while Playing the video file.
Choose the Info icon and press OK can display the Info
EXIT Back Move OK Select
MENU.
Press the◀▶ to select the right disk and press OK to
display media files and folder list or choose Return to
back to the media type selection menu.
jafeimao.VOB
Picture
Resolution: 720 x 480
Audio Track: 1 / 6
Subtitle: 1 / 11
Program: – / 0
0021.JPG
Size: 1048404 KByt..
return
Close
Select the media file by pressing◀▶ or ▼▲ , then
the preview frame will pop up. Press the button
to play the media file in full screen. When the
media file (photo, music, Movie or text type) is
playing, press the OK or Info button can display the
control bar.
- 38 -
Service Manual
Model No.:
content:
1: ADC setup: set ADC value of YUV,VGA. It can also be auto-set. Adopt 100%
color bar to yuv and Checkerboard signal to vga.
2:Adjust the brightness and contrast ratio of each signal, which do not affect the
value of user's menu.
3: adjust the color temperature and white balance of each signal source.
4: SSC to adjust the spectrum for passing the EMC test.
5:special set
1)2hour off-- for Aging test
2)WDT --watch dog
3)white pattern --set pure color output for the panel, used at the checking and
aging test for panel.
4)reset
5)set the recorder
6)set power-on screen display.
6:QMAP adjust :adjust color quality.
7:PEQ set sound EQ
8:sw information: to check the sofeware information
9:UART DEBUG : Access to serial port and connect a computer if set to HK.
10:BMTEST :cpu check the CPU
The last line is SW Ver.No
- 39 -
Service Manual
Model No.:
2.2,then input USB , press "MENU" and choose "update software", and then press "OK".
2.3,Now you should choose "Yes",TV begin to update.You should reset TV after update.
- 40 -
Service Manual
Model No.:
Content:
- 41 -
Service Manual
Model No.:
9. Trouble shooting
- 51 -
Service Manual
Model No.:
Yes
Yes
Check if there is +12V at No
Pin30 in J1
Check if PQ6 No Replace PQ6 、
Yes 、PR46 PD14
Replace the QD6 works normally
Change LVDS wire
Still having
Change Panel
problems
- 52 -
Service Manual
Model No.:
Yes
No
Check if there is signal at C222 and C223 Check the input source
Yes
No
Check if there is signal at CD744 and CD743 Change U23
Yes
No
Check if there is signal at FB6,FB8,FB8,FB10 12V
Check LD3 voltage Change UD4
Yes Else
Still having problems Change Mainboard
- 53 -
Service Manual
Model No.:
Check `PD1(12V``) No
Change Mainboard
Yes
Check PD3(12V) No Change Mainboard
Yes
No
Check LD22(3.3V) Change UD8
Yes No
Check Q4(3.3V) Change Q4
Yes
Check CD90(1.15V) No Change UD9
Check C137(1.8V) Change U1
Check R216(3.3V`)` Change Q4
Still having problems
Yes No
Change mainchip Change Mainboard
U23
Change
Mainboard
- 54 -
Service Manual
Model No.:
Poor sound
Poor sound
For ease of use, recommend that customer format the picture and sound
settings in the automatic option.
Update the software and
Still having
make the reboot; or
problems
change the Mainboard
- 55 -
Service Manual
Model No.:
Yes
Yes
Refer to relative
instructions in the
Manual for color adjust
Updata the software and
Still having make the reboot; or
problems change the maiboard
- 56 -
Service Manual
Model No.:
Still having Check if Main board / LVDS wire / Panel are in
problems good condition ?
- 57 -
Trouble Shooting
• Mainboard not work Panel not work
• 1. check if there is +12V/+5V output 1. check if the voltage input and
on the power board output of voltage boost IC of the
• 2.Verify if the DC/DC convertors have backlight is OK.
the right output (5V,3.3V,1.8V,1.15V) 2.Verify if the Mainboard output the
• 3.Verify if the Mainchip(MSV56), right On/Off signal to power board;
AudioAMP…solder well; 3.Verify if the Mainboard output the
• 4.Verify if the U204) has the right LVDS singal to panel T‐con board
software and work well; 4.Verify if the software is the right
• 5.Verify if the YS1(Crystal) has the right version of this model.
frequency 5.Change the LVDS wire to check if it’s
broken.
Trouble Shooting
Power board not work
1.Verify if the power cord connect well?
2. check if +5Vstandby of the power board
part is functioning normally;
3. Check if voltage of the POWER ON/OFF of
the power board part is on the high level
voltage
4. +12V/+5V output ;check if there is
+12V/+5V output on the power board.
5.Check if Main board / LVDS wire / Panel
are in good condition ?
- 60 -
Service Manual
Model No.:
Horizontal gary
H Dim
line
Horizontal
H L/D line(light or dark
forever)
- 61 -
Service Manual
Model No.:
Panel or
Polarlzer Tine or rigidity arose
- 62 -
Service Manual
Model No.:
Failure Mode
FIIcker Crosstalk
LCD
Vcom imbalance
Circuit
Abnormal Color Only
Capacitance
color abormal
improper bring
crosstalk inside
LCD pannel
Only
1.Chip
Abnormal Color color abnormal
lose action
2.IC short or
jointion bad
3.Pannel and vsc
connect bad
- 63 -
Service Manual
Model No.:
Failure Mode
- 64 -
Service Manual
Model No.:
Failure Mode
- 65 -