Professional Documents
Culture Documents
Gauge = 1435 mm
CORRECTION VALUES
FOR THE LEVELLING SYSTEM
IIKII
TRANSITION CORRECTION VALUE
IIXII
VERTICAL CURVE CORRECTION VALUE
MF = 12,100 m
RF 18,150 m
FFO = 0,000 m
R M F FO
PlasseraTheuner NT- 133 1
IIKII
LIFT SETTING CORRECTION VALUE
FOR TRANSITIONS
The correction value "K" depends on radius,superelevation and gauge of the track.
The amount of lift to be set to the front levelling feeler "F" has to be reduced by the
correction value "K" enscribed in the list (next page).
ADJUSTING PROCEDURE:
Find the correction value "K" for relevant superelevation "Ü" and radius "R". lt also
important to know the lenght of superelevation ramp (distance between"RA"and"RE").
As soon as the front levelling feeler "F" is at the beginning of the upgoing ramp"RA" the
adjustment commences linear increasing in such a way that the maximum of the
correction value "K" is reached at the end of the ramp "RE".
The "K" value remains constant throught the whole superelevated curve.
Decrease of the "K"value takes place also liner between the next
' RE - RA' ( downgoing ramp ).
RE R E
RA RA
Note: The a.m. abbreviations refer to the german permanent way terminology
RA = Beginning of superelevation ramp*)
RE = End of superelevation ramp *)
IIXII
LIFT SETTING CORRECTION VALUE
FOR VERTICAL CURVES
ln general vertical curves are circular curves with minimum radius of 2000 metres
tangential to chanches in gradients.
The correction value "X" depends on the radius of the vertical curve "R".
AA AE
AA AE
ADJUSTING PROCEDURE:
Find the correction value "X" for relevant vertical radius "R".
As soon as the front levelling feeler "F" is at the beginning of vertical curve "AA" the
adjustment of the correction value "X" commences according to distance-depending
graduation enscribed in the adjusting table "X afterAA".
Full amount of "X" remains constant until the end of vertical curve "AE" is reached.
From now on the "X" value is decreasing according to the graduation in the adjusting
table "X after AE".
X= 109808 R
Part of X 0,00 0,01 0,04 0,09 0,16 0,26 0,37 0,50 0,66 0,74 0,83 0,91 0,99 1,00 1,00 1,00 1,00 1,00
M.after AA 0,00 1,50 3,00 4,50 6,00 7,50 9,00 10,50 12,00 '13,50 15,00 16,50 18,00 18,15 21,00 22,50 24,00 25,50
RADIUS
2000 0 1 2 5 I 14 20 28 36 41 45 50 54 55 55 55 55 55
2200 0 1 2 5 8 13 18 25 33 37 41 45 50 50 50 50 50 50
2400 0 0 2 4 I 12 17 23 30 34 38 42 45 46 46 46 46 46
2600 0 0 2 4 7 11 16 21 28 31 35 38 42 42 42 42 42 42
2800 0 0 2 4 6 10 14 20 26 29 32 36 39 39 39 39 39 39
3000 0 0 2 3 6 9 14 18 24 27 30 33 36 37 37 37 37 37
3500 0 0 1 3 5 I 12 1ô 21 23 26 29 31 31 31 31 31 31
4000 0 0 1 3 5 7 10 14 18 20 23 25 27 27 27 27 27 27
4500 0 0 1 2 4 ô 9 12 16 18 20 22 24 24 24 24 24 24
5000 0 0 1 2 4 6 I 11 14 16 18 20 22 22 22 22 22 22
5500 0 0 1 2 3 5 7 10 13 15 17 18 20 20 20 20 20 20
6000 0 0 1 2 3 5 7 I 12 14 15 17 18 18 18 18 18 18
6500 0 0 1 2 J 4 EI I 11 13 14 15 17 17 17 17 17 17
7000 0 0 1 1 3 4 6 I 10 12 13 14 1ô 16 16 16 16 16
8000 0 0 1 1 2 4 5 7 I 10 11 12 14 '14 14 14 14 14
9000 0 0 1 1 2 3 5 6 8 I 10 11 12 12 12 12 12 12
1 0000 0 0 0 1 2 3 4 6 7 8 I 10 11 1'l 11 11 11 11
1 2000 0 0 0 1 2 2 3 5 6 7 8 8 I I 9 9 I I
1 5000 0 0 0 1 1 2 3 4 5 5 o 7 7 7 7 7 7 7
20000 0 0 0 1 1 1 2 3 4 4 5 5 5 5 5 5 5 5
30000 0 0 0 0 1 1 1 2 2 3 3 3 4 4 4 4 4 4
50000 0 0 0 0 0 1 1 1 1 2 2 2 2 2 2 2 2 2
1 00000 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 1
PlasseraTheuner NT- 133 5
Part of X 1,00 0,92 0,83 0,75 0,67 0, 52 0,38 0,27 0,17 0,10 0,05 0 01 0,00 0,00 0,00 0,00 0,00 0,00
M.after AE 0,00 1,5 3,00 4,50 6,00 7,50 9,00 10,50 't2,oo '13,50 15,00 16,50 18,00 18,15 0,00 0,00 0,00 0,00
RADIUS
2000 55 50 46 41 37 28 21 15 I 5 2 1 0 0 0 0 0 0
2200 50 46 42 38 33 26 19 13 I 5 2 1 0 0 0 0 0 0
2400 46 42 38 34 31 24 17 12 I 5 2 1 0 0 0 0 0 0
2600 42 39 35 32 28 22 16 11 7 4 2 1 0 0 0 0 0 0
2800 39 36 33 29 26 20 15 10 7 4 2 0 0 0 0 0 0 0
3000 37 34 31 28 25 19 14 10 o 4 2 0 0 0 0 0 0 0
3500 31 29 26 24 21 16 12 I 5 3 1 0 0 0 0 0 0 0
4000 27 25 23 21 18 14 10 7 5 3 1 0 0 0 0 0 0 0
4500 24 22 20 18 16 13 9 7 4 2 1 0 0 0 0 0 0 0
5000 22 20 18 17 15 11 8 6 4 2 1 0 0 0 0 0 0 0
5500 20 18 17 15 13 10 8 5 3 2 1 0 0 0 0 0 0 0
6000 18 17 15 14 12 I 7 5 3 2 1 0 0 0 0 0 0 0
6500 17 15 14 13 11 I ô 5 3 2 1 0 0 0 0 0 0 0
7000 16 14 13 12 11 I 6 4 3 2 1 0 0 0 0 0 0 0
8000 14 13 11 10 I 7 5 4 2 1 1 0 0 0 0 0 0 0
9000 12 11 10 I 8 6 5 3 2 1 1 0 0 0 0 0 0 0
1 0000 11 10 I 8 7 6 4 3 2 1 0 0 0 0 0 0 0 0
12000 I I 8 7 6 5 3 2 2 1 0 0 0 0 0 0 0 0
1 5000 7 7 ô 6 5 4 3 2 1 1 0 0 0 0 0 0 0 0
20000 5 5 5 4 4 3 2 1 1 1 0 0 0 0 0 0 0 0
30000 4 3 3 3 2 2 1 1 1 0 0 0 0 0 0 0 0 0
50000 2 2 2 2 1 1 1 1 0 0 0 0 0 0 0 0 0 0
1 00000 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0