Professional Documents
Culture Documents
Dr. ZX Operating Manual Dr. ZX Operating Manual Dr. ZX Operating Manual Dr. ZX Operating Manual
Dr. ZX Operating Manual Dr. ZX Operating Manual Dr. ZX Operating Manual Dr. ZX Operating Manual
ZX Operating Manual
A. EPVC_Mid
Performs Self-diagnosis, sensor output monitoring etc. on ZX70 to ZX370MTH, EX60 to
EX370 Dash -2/-3/-5, and same range of Fiat-Hitachi models.
B. EPVC_Large
Performs Self-diagnosis, sensor output monitoring etc. on ZX450 to ZX850H, EX400 to
EX800 Dash-3/-5, and same range of Fiat-Hitachi models.
C. HMS_LargeMid
Performs ICX Self-diagnosis, ICX set-up on ZX70 to ZX850H.
A. EPVC-
EPVC-Mid
STD Cab
US Cab
Tap “Dr.ZX
Dr.ZX”
Dr.ZX icon.
Tap “EPVC_Mid
EPVC_Mid”.
EPVC_Mid
(1) (2)
Tap “Operation
Operation Manual
Manual”.
anual Tap “Op.
Op. Mode
Mode”.
ode
(3)
(1) (2)
Tap “Op.
Op. Manual”.
Manual Tap “Service
Service Mode”.
Mode
(3)
(1) (2)
Tap “Op.
Op. Manual”.
Manual Tap “Engine
Engine Learning Mode”.
Mode
(3)
Please confirm that the “Operation Mode” procedure has been completed, refer to
3.2.1 Fig 3.
Tap “Start
Start”.
Start If displayed model is the Tap “Self
Self-
Self-Diagnostic
same as the unit under Results”
Results
test, tap “Correct
Correct”.
Correct
Tap “Details
Details”
Details to Tap up-arrow or down-arrow to scroll
display error code display error information. Tap “ESC
ESC”
ESC to
information. go to the retry screen.
Tap “Retry
Retry B”
B to re-try
self-diagnostic. Tap “ESC
ESC”
ESC to
return to function menu.
3-4, Monitoring/Recording Pressure etc.
Note
Following explanations are based on the ZX200. Screens will vary by model.
Please confirm that the “Operation Mode” procedure has been completed, refer to
3.2.1 Fig 3.
Tap “Start
Start”.
Start If displayed model is the Tap “Monitor
Monitor Display”.
Display
same as the unit under test,
tap “Correct
Correct”.
Correct
(4) Enter model code & s/no. Enter model code and s/no. After entering
tap “OK
OK”
OK to go to the monitor-selecting
menu. If no model code and/or s/no are
entered, no monitoring data can be
recorded.
Up-arrow/Down-arrow
(6) Monitoring screen
Tap “Hold
Hold”
Hold to stop the
graph.
(9) Confirmation
If selected data bank is empty the left screen will be displayed. Tap “Write
Write”
Write to record data.
If selected data bank already has data, the right screen will be displayed. If you want
overwrite recoded data in this bank, tap “Overwrite
Overwrite”.
Overwrite Tap ”ESC
ESC”
ESC to return to the data
bank selecting menu.
(10)
Tap “Comment
Comment”
Comment to go to the next screen. Even if you
have no comments please tap “Comment
Comment”.
Comment
Tap “OK
OK”
OK to record the data to the data bank you have
selected. If you wish to return to the comment entry screen,
tap “ESC
ESC”.
ESC
3-5, Replaying Recorded Data
Tap “Record
Record Disp”
Disp to start replay.
(4) Replaying
Tap “Hold
Hold”
Hold to stop replay.
ESC to return to the data bank selection screen.
Tap “ESC
ESC”
3-6, Special Function
Note
Following explanations are based on the ZX200. Screens will vary by model.
Please confirm that the “Operation Mode” procedure has been completed, refer to
3.2.1 Fig 3.
Tap “Start
Start”.
Start If the displayed model is Tap “Special
Special Function”.
Function
same as the unit under
test, tap “Correct
Correct”.
Correct
Tap “ESC
ESC”
ESC to return to main menu.
3-6-1, Special Function –WU Deactivation
Start the engine while the Hydraulic Oil temperature is cold; the machines
computer will increase the engine low idle rpm from the standard low idle rpm to
warm-up the Hydraulic Oil. “WU Deactivation” means, cancel this function.
Tap “WU
WU Deactivation”
Deactivation to deactivate (stop) the
warm-up function.
Tap “Execute
Execute”
Execute to start deactivation (stop the warm-up
function).
Tap “ECO
ECO Deactivation”
Deactivation to deactivate (stop) this
function.
Tap “Execute
Execute”
Execute to start deactivation (stop the ECO
function)
Please confirm that the “Operation Mode” procedure has been completed, refer to
3.2.1 Fig 3.
Tap “Start
Start”.
Start
Tap “Rechecked
Rechecked”
Rechecked to confirm you are in service mode.
(4)
Tap “Special
Special Function
Function”.
ion
Tap “Learning
Learning Data Display”.
Display
Tap “ESC
ESC”
ESC to return to the function menu.
Tap “EC
EC Motor Stop Position”.
Position
(7)-2 Display information
Tap “ESC
ESC”
ESC to return to the learning data display
menu.
Tap “EC
EC Motor Maximum Speed Position”.
Position
Tap “ESC
ESC”
ESC to return to the learning data display
menu.
(9)-1 Display boom angle sensor correction value
Tap “Boom
Boom Angle Sensor Correction Value”.
Value
Tap “ESC
ESC”
ESC to return to the learning data display
menu.
Tap “Arm
Arm Angle Sensor Correction Value”.
Value
Tap “ESC
ESC”
ESC to return to the learning data display
menu.
3-8, Parameters Adjustment
Note
-Following explanations are based on the ZX200. Screen will vary by model.
Please confirm that the “Operation Mode” procedure has been completed, refer to
3.2.1 Fig 3. and engine-learning switch is “ON
ON”
ON position.
Tap “Start
Start”.
Start
Tap “Rechecked
Rechecked”
Rechecked to confirm you are in service mode.
(4)
Tap “Special
Special Function”.
Function
Tap “Parameter
Parameter Change”.
Change
Tap “Li
Li speed adjustment”.
adjustment
This section describes how to set-up the displayed information on the hour-meter
display.
Please confirm that the “Operation Mode” procedure has been completed, refer to
3.2.1 Fig 3.and engine-learning switch is “ON
ON”
ON position.
Tap “Start
Start”.
Start
Tap “Rechecked
Rechecked”
Rechecked to confirm you are in the service
mode.
(4)
Tap “Special
Special Function”.
Function
Tap “Monitor
Monitor Display”.
Display
Tap “Engine
Engine Actual
Actual Speed“.
Speed Tap “ESC
ESC”
ESC to return to
function menu.
Tap “Disp
Disp”
Disp to display engine actual speed on the hour
meter display. If you do not wish to show engine
actual speed, tap “No
No Disp”.
Disp
(8) Confirming screen
US Cab
Tap “Dr.ZX
Dr.ZX”
Dr.ZX icon.
Tap “EPVC_Large
EPVC_Large”.
EPVC_Large
(1) (2)
Tap “Operation
Operation Manual
Manual”.
anual Tap “Op.
Op. Mode
Mode”.
ode
(3)
(1) (2)
Tap “Op.
Op. Manual
Manual”.
al Tap “Service
Service Mode”.
Mode
(3)
(1) (2)
Tap “Op.
Op. Manual”.
Manual Tap “Engine
Engine Learning Mode”.
Mode
(3)
Please confirm that the “Operation Mode” procedure has been completed, refer to
3.2 Fig 3.
Tap “Start
Start”.
Start If the displayed model is same Tap “Self
Self-
Self-Diagnostic
as the unit on test, tap Results”
Results
“Correct
Correct”.
Correct
Tap “Details
Details”
Details to Tap the up-arrow or down-arrow to
show error code display error information. Tap “ESC
ESC”
ESC to
information. go to the retry screen.
Tap “Retry
Retry B”
B to re-try
self-diagnostic. Tap “ESC
ESC”
ESC to
return to function menu.
3-4, Monitoring/Recording
Monitoring/Recording Pressure etc.
Note
Following explanations are based on the ZX450. Screens
Screens will vary by model.
Please confirm that the “Operation Mode” procedure has been completed, refer to
3.2 Fig 3.
Tap “Start
Start”.
Start If the displayed model is Tap “Monitor
Monitor Display”.
Display
same as the unit on test, tap
“Correct
Correct”.
Correct
Up-arrow/Down-arrow
Tap “Hold
Hold”
Hold to stop
graph.
If the selected data bank is empty, left screen will be displayed. Tap “Write
Write”
Write to record
data. If selected data bank already has data, right screen will be displayed. If you
want to overwrite recoded data in this bank, tap “Overwrite
Overwrite”.
Overwrite Tap ”ESC
ESC”
ESC to return to
data bank selecting menu.
(10)
Tap “Comment
Comment”
Comment to go to the next screen. Even if you
have no comments please tap “Comment
Comment”.
Comment
Tap “OK
OK”
OK to record the data to the data bank you
selected. If you want to return to the comment entry
screen, tap “ESC
ESC”.
ESC
3-5, Replaying Recorded Data
(4) Replaying
Tap “Hold
Hold”
Hold to stop replay.
ESC to return to data bank selection screen.
Tap “ESC
ESC”
3-6, Special Function
Note
Following explanations are based on the ZX450. Screens will vary by model.
Please confirm that the “Operation Mode” procedure has been completed, refer to
3.2 Fig 3.
Tap “Start
Start”.
Start If displayed model is Tap “Special
Special Function”.
Function
same as the unit on
test, tap “Correct
Correct”.
Correct
Tap “WU
WU Deactivation”
Deactivation to start this function. (Stop
the warm-up function)
Tap “Execute
Execute”
Execute to start deactivation. (Stop the
warm-up function)
Tap “ECO
ECO Deactivation”
Deactivation to start this function.
Tap “Execute
Execute”
Execute for start deactivation (Stop the ECO
Function)
Tap “Pump
Pump Adjustment”
Adjustment to start this function.
(2)
Tap “Max.
Max. Disp. Holding”
Holding
Tap “ESC
ESC”.
ESC
3-7, Display Engine Learning Data
Note
Following explanations are based on the ZX450. Screens will vary by model.
Please confirm that the “Operation Mode” procedure has been completed, refer to
3.2 Fig 3.
Tap “Start
Start”.
Start
Tap “Rechecked
Rechecked”
Rechecked to confirm you are in the service
mode.
(4)
Tap “Special
Special Function”.
Function
Tap “Learning
Learning Data Display”.
Display
Tap “ESC
ESC”
ESC to return to the function
menu.
Tap “EC
EC Motor Stop Position”.
Position
(7)-2 Display information
Tap “ESC
ESC”
ESC to return to engine learning data display
menu.
Tap “EC
EC Motor Maximum Speed Position”.
Position
Tap “ESC
ESC”
ESC to return to the engine learning data
display menu.
3-8, Parameters Adjustment
Note
Following explanations are based on the ZX450. Screens will vary by model.
Please confirm that the “Operation Mode” procedure has been completed, refer to
3.2 Fig 3.and engine-learning switch is “ON
ON”
ON position.
Tap “Start
Start”.
Start
Tap “Rechecked
Rechecked”
Rechecked to confirm you are in the service
mode.
(4)
Tap “Special
Special Function”.
Function
Tap “Parameter
Parameter Change”.
Change
Tap “Li
Li speed adjustment”.
adjustment
Tap “Lubrication
Lubrication Interval (STANDARD
(STANDARD)”.
Tap “ESC
ESC”
ESC to return to the selection menu.
Tap “ESC
ESC”
ESC to return to the
function menu
Tap “Act/Deact.
Act/Deact. of Parameters”
Parameters to reflect the adjusted
figure to the controller.
Tap “Act
Act.”
Act to reflect the adjusted figure to the
ESC to return to function menu.
controller. Tap “ESC
ESC”
(8) Confirming screen
Please confirm that the “Operation Mode” procedure has been completed, refer to
3.2 Fig 3.and engine-learning switch is “ON
ON”
ON position.
Tap “Start
Start”.
Start
Tap “Rechecked
Rechecked”
Rechecked to confirm you are in service mode.
(4)
Tap “Special
Special Function”.
Function
Tap “Monitor
Monitor Display Change
Change”.
ge
Tap “Engine
Engine Actual Speed“.
Speed Tap “ESC
ESC”
ESC to return to
the function menu.
Tap “Disp
Disp”
Disp to display engine actual speed on the hour
meter display. If you wish not to show engine actual
speed, tap “No
No Disp”.
Disp
(8) Confirming screen
Tap “Password
Password”.
Password
1, Necessary Tools
1-1, Palm with Dr.ZX software.
STD Cab
Palm
US Cab
5-5, When the downloading has finished (normally), the following screen will be
displayed Tap “OK
OK”.
OK
6-2, Password input screen will be displayed, enter password, and tap “OK”.
6-3, ICX set-up program main screen will be displayed. Tap “Start
Start”.
Start
7, Entering Time Differences
Differences from UTC (GMT)
To set the time difference between local time and UTC (GMT)
Tap “0
0”, “1
1”, and tap “abc
abc”
abc to enter letters. If you want to correct input figures, tap
Right-arrow for delete.
9-7, Tap “ccap”
ap to enter capital letters.
9-8, Tap “G
G”, and tap “123
123”
123 to enter numbers.
9-9, Tap “6
6”, and tap “Done
Done”.
Done
9-10, Tap equipment serial number input space.
9-12, Enter six (6) digits of equipment serial number written on nameplate, and tap
“Done
Done”.
Done
9-15, When changing/setting model code and/or serial number, you have to clear
ICX internal memory to prevent any download error. Tap “Clear
Clear”.
Clear
10-2, If the internal hour meter and the external hour meter show different figures,
tap “Set
Set”
Set synchronizing. If both figures show same figures, tap “ESC
ESC”
ESC to quit hour
meter synchronizing function.
10-3, If you tapped “Set”, the following screen will be displayed. Tap “OK
OK”
OK to quit
hour meter synchronizing.
11, ICX Self-
Self-Diagnosis
Before starting the ICX self-diagnosis, turn on the key switch and wait for a period
of more than one (1) minute. Otherwise the ICX cannot perform an accurate
self-diagnosis.
11-2, If there are no faults, the following screen will be displayed. Tap “ESC
ESC”
ESC to quit
the self-diagnosis function.
11-3, If the ICX detects any error(s), fault code(s) will be displayed. Tap “Detailers
Detailers”
Detailers
to check the details of the error code, and tap “ESC
ESC”
ESC to quit ICX self-diagnosis
function.
12, Setting Downloading Operators Name
If you want to set or change the downloading operators name, follow the procedure
below.