Professional Documents
Culture Documents
CJ19M10/CJ20M10 / 20MJ10
COLOR TELEVISION
POWER
– VOL + 9 CH 8
VIDEO IN AUDIO
Chassis No. SN-70
– VOL + ? CH > VIDEO IN AUDIO
POWER
19J-M100/150/100S
CJ19M10
20J-M100
CJ20M10
19J-M100/19J-M100S
19J-M150/CJ19M10
MODELS 20J-M100/CJ20M10/20MJ10
In the interests of user-safety (Required by safety regulations in some countries ) the set should be restored to its
original condition and only parts identical to those specified should be used.
ELECTRICAL SPECIFICATIONS
POWER INPUT ........................... 120 V AC 60 Hz OUTPUT RATING ........ 0.9W (at 10% distortion)
POWER RATING .......................................... 84 W SPEAKER
PICTURE SIZE ............... 19":1194cm2(185sq inch) SIZE ................................................ 8cm(Round)
.................................... 20":1240cm2(192sq inch) VOICE COIL IMPEDANCE ....... 8ohm at 400 Hz
CONVERGENCE .................................... Magnetic ANTENNA INPUT IMPEDANCE
SWEEP DEFLECTION ............................ Magnetic VHF/UHF ............................ 75 ohm Unbalanced
FOCUS ....................... Hi-Bi-Potential Electrostatic TUNING RANGES
INTERMEDIATE FREQUENCIES VHF-Channels ....................................... 2thru 13
Picture IF Carrier Frequency ............. 45.75 MHz UHF-Channels .................................... 14thru 69
Sound IF Carrier Frequency .............. 41.25 MHz CATV Channels ................................... 1thru 125
Color Sub-Carrier Frequency ............ 42.17 MHz USA: (EIA, Channel Plan)
(Nominal) Specifications are subject to change without prior
AUDIO POWER notice.
CONTENTS
Page
æ ELECTRICAL SPECIFICATIONS ............................................................................................ 1
æ IMPORTANT SERVICE SAFETY PRECAUTION ...................................................................2
æ LOCATION OF USER'S CONTROL ........................................................................................ 6
æ INSTALLATION AND SERVICE INSTRUCTIONS ...................................................................7
æ CHASSIS LAYOUT ............................................................................................................... 13
æ BLOCK DIAGRAM ................................................................................................................ 14
æ SCHEMATIC DIAGRAMS ..................................................................................................... 15
æ PRINTED WIRING BOARD ASSEMBLIES ........................................................................... 21
æ REPLACEMENT PARTS LIST .............................................................................................. 27
æ PACKING OF THE SET ........................................................................................................ 35
2
19J-M100/100S/150/20J-M100
CJ19M10/CJ20M10 / 20MJ10
BEFORE RETURNING THE RECEIVER æ Connect the resistor connection to all exposed metal
parts having a return to the chassis
(Fire & Shock Hazard) (antenna, metal cabinet, screw heads, knobs and
Before returning the receiver to the user, perform control shafts, escutcheon, etc.) and measure the
the following safety checks. AC voltage drop across the resistor.
AII check must be repeated with the AC line cord
1. Inspect all lead dress to make certain that leads are plug connection reversed. (IF necessary, a non-
not pinched or that hardware is not lodged between polarized adapter plug must be used only for the
the chassis and other metal parts in the receiver. purpose of completing these check.)
2. Inspect all protective devices such as non-metallic Any current measured must not exceed 0.5 milliamp.
control knobs, insulating materials, cabinet backs, Any measurements not within the limits outlined
adjustment and compartment covers or shields, above are indicative of a potential shock hazard and
isolation resistor-capacity networks, mechanical corrective action must be taken before returning the
insulators, etc. instrument to the customer.
3. To be sure that no shock hazard exists, check for
leakage current in the following manner.
æ Plug the AC cord directly into a 120 volt AC outlet,
0.15µF
TEST PROBE
TO EXPOSED CONNECT TO
METAL PARTS KNOWN EARTH
GROUND
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212
SAFETY NOTICE
Many electrical and mechanical parts in television For continued protection, replacement parts must be
receivers have special safety-related characteristics. identical to those used in the original circuit.
These characteristics are often not evident from visual The use of substitute replacement parts which do not
inspection, nor can protection afforded by them be have the same safety characteristics as the factory
necessarily increased by using replacement components recommended replacement parts shown in this service
rated for higher voltage, wattage, etc. manual, may create shock, fire, X-radiation or other
Replacement parts which have special safety hazards.
characteristics are identified in this manual; electrical
components having such features are identified by
" å " and shaded areas in the Replacement Parts
Lists and Schematic Diagrams.
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212
3
19J-M100/100S/150/20J-M100
CJ19M10/CJ20M10/ 20MJ10
4
19J-M100/100S/150/20J-M100
CJ19M10/CJ20M10 / 20MJ10
VERIFICATIONS CONTRE L'INCEN-DIE ET æ Toucher avec la sonde d'essai les pièces métalliques
LE CHOC ELECTRIQUE exposées qui présentent une voie de retour au
châssis (antenne, coffret métallique, tête des vis,
Avant de rendre le récepteur à l'utilisateur, effectuer arbres de commande et des boutons, écusson, etc.)
les vérifications suivantes. et mesurer la chute de tension CA en-travers de la
résistance. Toutes les vérifications doivent être
1. Inspecter tous les faisceaux de câbles pour s'assurer refaites après avoir inversé la fiche du cordon
que les fils ne soient pas pincés ou qu'un outil ne d'alimentation. (Si nécessaire, une prise d'adpatation
soit pas placé entre le châssis et les autres pièces non polarisée peut être utilisée dans le but de
métalliques du récepteur. terminer ces vérifications.)
2. Inspecter tous les dispositifs de protection comme Tous les courants mesurés ne doivent pas dépasser
les boutons de commande non-métalliques, les 0,5 mA.
isolants, le dos du coffret, les couvercles ou blindages Dans le cas contraire, il y a une possibilité de choc
de réglage et de compartiment, les réseaux de électrique qui doit être supprimée avant de rendre le
résistance-capacité, les isolateurs mécaniques, etc. récepteur au client.
3. S'assurer qu'il n'y ait pas de danger d'électrocution
en vérifiant la fuite de courant, de la facon suivante:
æ Brancher le cordon d'alimentation directem-ent à une
0.15µF
SONDE D'ESSAI
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212
AVIS POUR LA SECURITE
De nombreuses pièces, électriques et mécaniques, dans identifiées par la marque " å " et hachurées dans la
les téléviseurs présentent des caractéristiques spéciales liste des pièces de remplacement et les diagrammes
relatives à la sécurité, qui ne sont souvent pas évidentes schématiques.
à vue. Le degré de protection ne peut pas être Pour assurer la protection, ces pièces doivent être
nécessairement augmentée en utilisant des pièces de identiques à celles utilisées dans le circuit d'origine.
remplacement étalonnées pour haute tension, L'utilisation de pièces qui n'ont pas les mêmes
puissance, etc. caractéristiques que les pièces recommandées par
Les pièces de remplacement qui présentent ces l'usine, indiquées dans ce manuel, peut provoquer des
caractéristiques sont identifiées dans ce manuel; les électrocutions, incendies, radiations X ou autres
pièces électriques qui présentent ces particularités sont accidents.
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212
12345678901234567890123456789012123456789012345678901234567890121234567890123456789012345678901212
5
19J-M100/100S/150/20J-M100
CJ19M10/CJ20M10/ 20MJ10
6
19J-M100/100S/150/20J-M100
CJ19M10/CJ20M10 / 20MJ10
20J-M100/CJ20M10
7
19J-M100/100S/150/20J-M100
CJ19M10/CJ20M10/ 20MJ10
8
19J-M100/100S/150/20J-M100
CJ19M10/CJ20M10 / 20MJ10
For adjustments of this model, the bus data is convered to various analog signals by the D-A converter
circuit.
Note: There are still a few analog adjustments in this series such as focus and master screen voltage.
Follow the steps below whenever service adjustment is required. See Figure "B" to determine if service adjust-
ments are required.
DATA NUMBER
S01 55 02
S01 D:00
Figure B.
9
19J-M100/100S/150/20J-M100
CJ19M10/CJ20M10/ 20MJ10
SERVICE DATA
ADJUSTMENT ITEM ADJUSTMENT CONTENTS
NUMBER INITIAL VALUE RANGE
S01 PICTURE 55 00-7F
S02 TINT 46 00-7F
S03 COLOR 32 00-7F
S04 BRIGHTNESS 40 00-7F
S05 SHARPNESS 28 00-3F Must be set to “24”
S06 VERTICAL PHASE 00 00-07 Must be set to “00”~"03"
S07 HORIZONTAL PHASE 12 00-1F
S08 RF-AGC 2A 00-3F
S09 VERTICAL AMP 20 00-3F
S10 VCO 2C 00-7F
S11 R CUT-OFF 00 00-FF
S12 G CUT -OFF 00 00-FF
S13 B CUT-OFF 00 00-FF
S14 G GAIN 7F 00-FF
S15 B GAIN 7F 00-FF
S16 TRAP(3.58MHz) 00 00 or 01 Must be set to “00”
S17 BALANCE 20 00-3F Must be set to “20”
S18 C.C.POSITION 18 00-7F
S19 Y-MUTE 00 00,01,03 00=NORMAL, 01=no”Y, 03=NO VERTICAL”
Table - A
Holding down both the CH UP/DOWN keys on the TV set at service mode for more then 2 seconds will automatically
write the above initial values into IC2101.
ADJUSTMENT
PART REPLACED NOTES
NECESSARY UNNECESSARY
Table - B
10
19J-M100/100S/150/20J-M100
CJ19M10/CJ20M10 / 20MJ10
Ë adjustment
VCO Adjustment White balance adjustment
1. Connect a digital voltmeter between pin (44) of IC201 1. Have unit receive a good local channel.
and ground. 2. Enter the service mode. select service adjustment
2. Select a good local channel. "S03" and set to "00" ( minimum color) . "S03" does
3. Enter the service mode. select adjustment "S10". not have to be adjusted if you selected a B/W picture
4. Adjust the data so that digital voltmeter shold read or monoscope pattern.
2.2V 3. Alternately adjust service adjustment data of "S14"
5. Adjustment is complete, remove the volt-meter, and "S15" untill a good grey scale with normal whites
return to "normal" mode. is obtained.
4. Select service adjustment "S03" and adjust data to
obtain normal color level.
RF AGC Adjustment
1. Have unit receive a good local channel. Sub-picture adjustment
2. Enter the service mode and select service adjustment
"S08". 1. Have unit receive a good local channel.
3. Set the data value to point where no noise or beat 2. Make sure the customer picture control is set to
appears. maximum.
4. Select another channel to confirm that no noise or 3. Enter the service mode and select service adjustment
beat appears. "S01".
NOTE1 :You will have to come out of the service 4. Adjust the data value to achieve normal contrast
mode to select another channel. range.
NOTE2 :Setting the data to "00" will pro-duce a
black raster. Sub-Tint Adjustment
1. Have unit receive a good local channel.
Screen adjustment 2. Set customer tint control to center of it's range.
3. Enter the service mode and select service adjustment
1. Connect a digital voltmeter between TP852 and "S02".
TP853 on the CRT socket PWB. 4. Adjust "S 02" data value to obtain normal flesh tones.
Note:These test points may not be provided.
Then connect the voltmeter to both ends of R852
located near Q852 on the foil side.
2. Select a good local channel.
3. Enter the service mode and select service adjustment
“S03” and set the data value to “00” to set the color
level to minimum.(Record original data code under
adjustment “S03” before changing) You may skip this
step if you selected a B/W picture or monoscope
pattern.
4. Select service adjustment “S19” and adjust the data
value to “01” this turn off the luminance signal (Y-
mute).
5. Select service adjustment "S04" and adjust data
value to obtain 0.17 volts on the digital voltmeter.
6. Adjust the master screen cotrol untill raster darkens
to the point where raster is barely seen.
7. Adjust service adjustments "S11" red,"S12" green
and "S13" blue to obtain a good grey scale with
normal whites at low brightness level.
8. Select service adjustment “S19” and reset data to
“00”.
Select service adjustment “S03” and reset data to
obtain normal color level.
9. Remove digital voltmeter.
Reset master screen cotrol to obtain normal
brightness range.
11
19J-M100/100S/150/20J-M100
CJ19M10/CJ20M10/ 20MJ10
Figure C.
12
19J-M100/100S/150 19J-M100/100S/150
CJ19M10/CJ20M10 CJ19M10/CJ20M10
G
G
MODEL 20MJ10 G
FF F
EE E
DD D
CC C
BB B
AA A
1 22 33 4 4 5 5 6 6 7 1 8 2 93 104 11
5 612
13 14
19J-M100/100S/150/CJ19M10/ 19J-M100/100S/150/CJ19M10/
20J-M100/CJ20M10 20J-M100/CJ20M10
E E
20MJ10
D D
C C
B B
A A
1 2 3 4 5 6 7 1 8 2 93 10
4 511 612
15 16
19J-M100/100S/150 19J-M100/100S/150
CJ19M10/CJ20M10 CJ19M10/CJ20M10
1 2 3 4 5 6 7 8 9 10 11 12
17 18
19J-M100/100S/150/CJ19M10/ 19J-M100/100S/150/CJ19M10/
20J-M100/CJ20M10 20J-M100/CJ20M10
F
PWB-B:CRT Unit (Wiring Side)
19 20
19J-M100/100S/150 19J-M100/100S/150
CJ19M10/CJ20M10 CJ19M10/CJ20M10
F
PWB-B:CRT Unit (Chip Parts Side)
1 2 3 4 5 6 7 8 9 10 11 12
21 22
19J-M100/100S/150/CJ19M10/ 19J-M100/100S/150/CJ19M10/
20J-M100/CJ20M10 20J-M100/CJ20M10
1 2 3 4 5 6 7 8 9 10 11 12
23 24
19J-M100/100S/150 19J-M100/100S/150
CJ19M10/CJ20M10 CJ19M10/CJ20M10
1 2 3 4 5 6 7 8 9 10 11 12
25 26
19J-M100/100S/150/CJ19M10
20J-M100/CJ20M10/20MJ10
Ref. No. Part No. ★ Description Code Ref. No. Part No. ★ Description Code
MARK★: SPARE PARTS-DELIVERY SECTION ★MARQUE: SECTION LIVRAISON DES PIECES DE RECHANGE
Ref. No. Part No. ★ Description Code Ref. No. Part No. ★ Description Code
DUNTK9273WEV0/V2/V4/V5
PICTURE TUBE DUNTK9316WEV0/V2 MAIN UNIT
19J-M100/150/CJ19M10 TUNER
çå V101 VB48AFS15X/*S M Picture Tube CC NOTE:THE PARTS HERE SHOWN ARE SUPPLIED AS AN ASSEM-
or VB48KZL70X/*S BLY BUT NOT INDEPENDETLY.
å L702 RCiLG0014MEZZ M Degaussing Coil AM å TU51 VTUVTST6UF78/ J Tuner BD
çå DY601 RCiLH0099MEZZ M Deflection Yoke AY
19J-M100S/20MJ10 INTEGRATED CIRCUITS
çå V101 VB48KRD89X/1E M Picture Tube CB çå IC201 RH-iX2933CEZZ J TAL268N AX
å L702 RCiLG0014MEZZ M Degaussing Coil AM çå IC201 RH-iX2573CEZZ J (20MJ10)
çå DY601 RCiLH0100MEZZ M Deflection Yoke AZ IC351 VHiTDA7233/-1 J TDA7233 AF
PMAGF3001MEZZ M Magnet Ass'y AG å IC501 VHiTA8403K/-1 J TA8403k AL
MSPRT0002MEZZ M Spring for CRT AA çå IC701 VHiSTR301301E J I.C. AP
QEARC1913MEZZ M Grounding part AE å IC751 VHiKA7809Pi-1 R KiA7809Pi AE
20J-M100/CJ20M10 IC2001 RH-iX2942CEZZ J TMPA8701CHF106 AV
çå V101 VB51KZR50X/*S M Picture Tube IC2040 VHiPST994C/-1 J PST994C AD
å DY601 RCiLH0105MEZZ M Deflection Yoke IC2101 RH-iX2447CEN1 J ST24C01B6 AL
å L702 RCiLG0017MEZZ M Degaussing Coil
TRANSISTORS
PRINTED WIRING BOARDASSEMBLYS You can substitute "VS2SD601AR/-1" for "VS2SC2462-C-1".
(NOT REPLACEMENT ITEM) Q201 VS2SC2735//1E J 2SC2735 AC
Q351 VS2SD601AR/-1 J 2SD601(AR) AC
PWB-A DUNTK9273WEV0 _ Main Unit (19J-M100/150) _
Q401 VS2SD601AR/-1 J 2SD601(AR) AC
PWB-A DUNTK9273WEV2 _ Main Unit (20J-M100) _
Q402 VS2SB709AR/-1 J 2SB709(AR) AC
PWB-A DUNTK9273WEV5 _ Main Unit (CJ20M10) _
Q403 VS2SD601AR/-1 J 2SD601(AR) AC
PWB-A DUNTK9273WEV4 _ Main Unit (CJ19M10) _
Q404 VS2SB709AR/-1 J 2SB709AR AC
PWB-A DUNTK9316WEV0 _ Main Unit (19J-M100S) _
Q451 VS2SB709AR/-1 J 2SB709AR AC
PWB-B DUNTK9274WEV2 _ CRT Unit (20J-M100/CJ20M10)
Q601 VS2SC2655Y/-1 J 2SC2655(Y) AE
PWB-B DUNTK9274WEV0 _ CRT Unit(19J-M100/150) _
å Q602 VS2SD2095//1E J 2SD2095 AN
PWB-B DUNTK9317WEV0 _ CRT Unit(19J-M100S) _
or VS2SD2095//1E
or VS2SD2499//1E
or VS2SD2586//1E
27
19J-M100/100S/150/CJ19M10
20J-M100/CJ20M10/20MJ10
Ref. No. Part No. ★ Description Code Ref. No. Part No. ★ Description Code
28
19J-M100/100S/150/CJ19M10
20J-M100/CJ20M10/20MJ10
Ref. No. Part No. ★ Description Code Ref. No. Part No. ★ Description Code
29
19J-M100/100S/150/CJ19M10
20J-M100/CJ20M10/20MJ10
Ref. No. Part No. ★ Description Code Ref. No. Part No. ★ Description Code
30
19J-M100/100S/150/CJ19M10
20J-M100/CJ20M10/20MJ10
Ref. No. Part No. ★ Description Code Ref. No. Part No. ★ Description Code
31
19J-M100/100S/150/CJ19M10
20J-M100/CJ20M10/20MJ10
Ref. No. Part No. ★ Description Code Ref. No. Part No. ★ Description Code
DUNTK9273WEV0/V2/V4/V5 DUNTK9274WEV0/V2
DUNTK9316WEV0/V2 MAIN UNIT DUNTK9317WEV0 CRT UNIT
R2049 VRN-MD2AL333J J 33k 0.1W Metal.Film AA TRANSISTORS
R2054 VRN-MD2AL103J J 10k 0.1W Metal.Film AA Q852 VS2SC2229O/1E J 2SC2229(O) AD
R2055 VRN-MD2AL103J J 10k 0.1W Metal.Film AA Q854 VS2SC2229O/1E J 2SC2229(O) AD
R2060 VRN-MD2AL221J J 220 0.1W Metal.Film AA Q856 VS2SC2229O/1E J 2SC2229(O) AD
R2061 VRN-MD2AL562J J 5.6k 0.1W Metal.Film AA Q881 VS2SA1266-Y-1 J 2SA1266(Y) AA
R2062 VRN-MD2AL183J J 18k 0.1W Metal.Film AA DIODES
R2063 VRD-RA2BE222J J 2.2k 1/8W Carbon AA D881 VHD1SS119//-1 J Diode AB
R2064 VRD-RA2BE332J J 3.3k 1/8W Carbon AA D882 VHD1SS119//-1 J Diode AB
R2066 VRN-MD2AL103J J 10k 0.1W Metal.Film AA D885 VHD1SS119//-1 J Diode AB
R2067 VRN-MD2AL103J J 10k 0.1W Metal.Film AA
R2068 VRN-MD2AL103J J 10k 0.1W Metal.Film AA COILS
R2070 VRN-MD2AL103J J 10k 0.1W Metal.Film AA L851 VP-DF151K0000 J 150µH AB
R2101 VRN-MD2AL101J J 100 0.1W Metal.Film AA R859 VRN-MD2AL470J J 47 0.1W Metal.Film AA
R2102 VRN-MD2AL101J J 100 0.1W Metal.Film AA R859 VRN-MD2AL470J J 47 0.1W Metal.Film AA
R2501 VRN-MD2AL123J J 12k 0.1W Metal.Film AA
R2503 VRN-MD2AL273J J 27k 0.1W Metal.Film AA CAPACITORS
R2504 VRN-MD2AL123J J 12k 0.1W Metal.Film AA C851 VCCCCY1HH271J J 270p 50V Ceramic AA
R2505 VRN-MD2AL563J J 56k 0.1W Metal.Film AA C852 VCCCCY1HH271J J 270p 50V Ceramic AA
R2506 VRD-RA2BE563J J 56k 1/8W Carbon AA C853 VCCCCY1HH271J J 270p 50V Ceramic AA
R2507 VRN-MD2AL823J J 82k 0.1W Metal.Film AA C854 RC-KZ0016CEZZ J 0.1 1.4kV Ceramic AC
R2508 VRN-MD2AL153J J 15k 0.1W Metal.Film AA C858 VCKYCY1HB102K J 1000p 50V Ceramic AA
R2509 VRN-MD2AL272J J 2.7k 0.1W Metal.Film AA C881 VCEA0A1CW106M J 10 16V EL. AB
R2601 VRD-RA2BE470J J 47 1/8W Carbon AA C883 VCEA0A1CW336M J 33 16V EL. AB
32
19J-M100/100S/150/CJ19M10
20J-M100/CJ20M10/20MJ10
Ref. No. Part No. ★ Description Code Ref. No. Part No. ★ Description Code
DUNTK9274WEV0/V2
DUNTK9317WEV0 CRT UNIT CABINET PARTS
MISCELLANEOUS PARTS
P851 QPLGN0561CEZZ J Plug AB
19J-M100/19J-M100S/CJ19M10/20MJ10
1 CCABA1266MES2 M Cabinet Front Ass'y BB
P852 QPLGN0461CEZZ J Plug AB
1-1 _ M Cabinet Front _
SC851 QSOCV0840CEZZ J Socket AK
1-2 GCOVA1031MEKA M Cover AD
or QSOCV0826CEZZ
1-3 HBDGB3009MESA M Badge "sharp" AC
(19J-M100/150/CJ19M10/20J-M100/CJ20M10)
1-4 JBTN-1090MEKA M Button,CH/VOL-up down AD
SC851 QSOCV0913CEZZ
2 GCABB1130MEKA M Rear Cabinet AX
or QSOCV0929CEZZ
(19J-M100S/20MJ10)
19J-M150
1 CCABA1266MES1 M Cabinet Front Ass'y BD
1-1 _ M Cabinet Front
1-2 GCOVA1031MEKA M Cover AD
1-3 HBDGB3009MESA M Badge "sharp" AC
1-4 JBTN-1090MEKB M Button,CH/VOL-up down AD
2 GCABB1130MEKB M Rear Cabinet AZ
1
1-1
1-3
2
POWER VIDEO IN AUDIO
– VOL + 9 CH 8
1-2 1-4
20J-M100/CJ20M10
1 CCABA1272MES0 M Cabinet Front Ass'y BF
1-1 _ M Cabinet Front _
1-2 GCOVA1034MEKA M Cover _
1-3 HBDGB3009MESA M Badge "sharp" AC
1-4 JBTN-1098MEKA M Button,CH/VOL-up down _
2 GCABB1126MEKA M Rear Cabinet AX
1 1-1
1-3
2
1-2 1-4
33
19J-M100/100S/150/CJ19M10
20J-M100/CJ20M10/20MJ10
Ref. No. Part No. ★ Description Code Ref. No. Part No. ★ Description Code
MISCELLANEOUS PARTS
å QACCD3014CESA M AC Cord AH
or QACCD3030CESA
QCNW-2110PEZZ R Connecting Cord _
QCNW-2111PEZZ R Connecting Cord _
QCNW-2112PEZZ R Connecting Cord _
VSP0080PBK98A M Speaker AG
or VSP0080P-E98S
SUPPLIED ACCESORRIES
PACKING PARTS
(NOT REPLACEMENT ITEM)
34
19J-M100/100S/150/CJ19M10
20J-M100/CJ20M10/20MJ10
Ref. No. Part No. ★ Description Code Ref. No. Part No. ★ Description Code
PACKING OF THE SET
★ Polystyrene Bag
Operation manual
Guarantee Card
and batteries
★Polystyrene mat
★ Buffer material
Use tapes to
fix the packing
case.
REAR
35
19J-M100/100S/150/CJ19M10
20J-M100/CJ20M10/20MJ10
Ref. No. Part No. ★ Description Code Ref. No. Part No. ★ Description Code
TQ0268-S
Printed in U.S.A
Y.O
36