Professional Documents
Culture Documents
Performing A Wenner Soil Resistivity Test With The AEMC Model 6472
Performing A Wenner Soil Resistivity Test With The AEMC Model 6472
Featured Product:
Performing a Wenner Soil Resistivity
Test with the AEMC® Model 6472
S oil resistivity is a key factor for determining what the resistance of a grounding
electrode will be, to what depth it must be driven in order to obtain low earth
resistance, and even the type of grounding system that should be designed for
this location and facility.
The resistivity of the soil varies widely throughout the world and changes
seasonally. Resistivity is strongly affected by the content of electrolytes in the
soil, its moisture content, and even its temperature. Soil resistivity measurements
are therefore critical for designing and constructing a grounding system
appropriate for your site and requirements.
This article describes a simple way to measure soil resistivity known as the
Wenner method. Our test instrument will be the AEMC® Ground Tester Model
6472. This instrument automatically calculates and displays soil resistivity, with
no manual calculations necessary.
The Model 6472 also features advanced capabilities such as test currents up
to 250 milliamps for testing soils with high resistivity, automatic test frequency
selection for testing in high EMI environments, and the ability to connect to a
computer via AEMC’s DataView ® data analysis software.
2
“WATTS CURRENT” TECHNICAL BULLETIN
Issue 09 Summer 2016
The Model 6472 automatically calculates soil resistivity using a formula that assumes the
auxiliary electrodes are inserted into the ground to a depth that does not exceed 1/20th
of the spacing distance between electrodes. So for our demonstration, we will place the
electrodes 10 feet apart and no more than 6 inches deep. Other distances can be used,
as long as depth does not exceed 1/20th of the spacing. Note that when calculating
the spacing-to-depth ratio, the spacing distance is the primary value. Determine the
electrode spacing first, and then adjust the depth accordingly.
The two outer electrodes are connected to the instrument’s outer terminals, labeled H
and E. The inner electrodes are connected the inner terminals, labeled S and ES.
3
“WATTS CURRENT” TECHNICAL BULLETIN
Issue 09 Summer 2016
To enable the instrument to accurately calculate soil resistivity, we must enter the electrode
spacing distance. We start by ensuring the instrument is configured for the correct units of
measure. Turn the instrument’s dial to the set-up setting. Then press the DISPLAY button. The unit
of measure, either meters (m) or feet (ft), appears blinking on the screen. Pressing the Up button
toggles between these two options. In our example we’re using feet, so if this is set to meters
press the Up button to change this setting.
Next, turn the dial to the 4-pole ρ setting. To enter the spacing distance, press the yellow button
labeled 2nd. The symbol 2nd appears on the screen, indicating buttons will now perform the
actions labeled in yellow.
Press the DISTANCE button. The word DISTANCE appears on the screen, and the first digit in the
distance field blinks, indicating it is in edit mode. Use the Up and Right buttons to navigate through
this field and make selections. For example, to set the distance to 10 feet, press the Right button
to navigate to the second digit and press the Up button to change this to 1. The field should now
be set to 10 feet.
4
“WATTS CURRENT” TECHNICAL BULLETIN
Issue 09 Summer 2016
You can save the setting by pressing the yellow 2nd button to enter 2nd mode and then pressing
the DISTANCE button.
You are now ready to take a soil resistivity measurement. To do this, push the START/STOP button
and hold it down for at least two seconds. After a few moments, the resistivity reading appears,
displayed in ohm-meters. The resistance of the soil between the two potential electrodes is also
displayed, in ohms.
To save the measurement in the instrument’s memory, press the MEM button twice. This saves
the reading, along with the date and time the reading was taken. This stored record can later be
displayed on the instrument’s screen, and downloaded to a computer using DataView® for further
analysis.
This concludes our quick explanation of how to perform a Wenner soil resistivity measurement with
the Model 6472. For more information about this instrument, please visit our Product Page.