Professional Documents
Culture Documents
N-L20
AUTO - ID TECHNICAL GUIDE
Rockwell ControlLogix
Connection Guide: EtherNet/IP Communication
This manual explains how to use EtherNet/IP communication to connect
to the N-L20 and the Rockwell ControlLogix Series.
This manual explains how to use EtherNet/IP communication to Chapter
CONFIGURING KEYENCE COMMUNICATION
connect to the N-L20 and the Rockwell ControlLogix Series.
3 UNIT N-L20 SETTINGS
Use the AutoID Network Navigator to configure the communication settings
TABLE OF CONTENTS
for the N-L20.
Chapter 1 EQUIPMENT USED
Chapter 2 CONNECTION METHODS
Chapter 3 CONFIGURING KEYENCE COMMUNICATION UNIT N-L20
SETTINGS 1 Use an USB cable to connect the PC and
the N-L20.
Chapter 4 CONNECTING AND SETTING UP THE CODE READER
PC
Chapter 5 CONFIGURING ROCKWELL CONTROLLOGIX SERIES N-L20 (AutoID Network Navigator)
SETTINGS
Chapter 6 TRNSMITTING SETTINGS AND MONITORING READING
DATA
USB Cable OP-51580
Chapter
1 EQUIPMENT USED
USB cable
OP-51580 (2 m)
General purpose
Ethernet cable
3 Change the settings to those of the desired fixed IP
address.
[ETHERNET]
Chapter
2 CONNECTION METHODS
Ethernet cable
2
When the message below is shown the connection
4 Click the “Start the setup wizard”, and set as shown
below. 2 was successful. Configure the SR-700 settings.
* The read screen cannot be displayed when settings are
configured via N-L20.
5 Send configuration
Click the send settings button in the upper right of AutoID Network
Navigator to send the settings to the N-L20.
Chapter
CONNECTING AND SETTING UP THE CODE
4 READER
Connect N-L20 and the BL-1300 Series. Press the
3
3 When the message below is shown the connection
was successful. Configure the BL-1300 settings. 2 New module Registration
* AGC cannot be lifted and tuning cannot be performed using Right-click [Controller Organizer] ➞ [I/O Configuration], and select
AutoID Network Navigator. To perform tuning, use N-UB or N-R2 “New Module”.
and AutoID Navigator.
Chapter
CONFIGURING ROCKWELL
5 CONTROLLOGIX SERIES SETTINGS
Select module opens, then expand the tree and select the unit to register.
The new module window opens. Select [Name] and [IP address]
and [Slot].
4
f. Configuration Settings
3 Registration of N-L20 to RSLogix5000 Assembly instance is 1(fixed) and Size is 0(fixed).
You can download the Tag Description CSV file on the WEB
(barcodereader.com). Once you receive this just save it to your computer,
then you will be ready to load it into your Allen-Bradley software. To do
this go to [Tool] ➞ [IMPORT] ➞ [Tags and Logic Comments] and choose
the file you were provided.
Once the new module is created click the [+] next to Communication and
select General Ethernet Module.
(ETHERNET-MODULE)
Set the ETHERNET-MODULE parameters: This will populate the bit descriptions like the following.
a. Name
Optional Setting, use “SR” if using Keyence Tag Description File (CSV file).
b. Comm Format
Optional Setting, choose from Data-INT(integer- 2Bytes),
Data-SINT(Single integer- 1Byte), or Data-DINT(Double integer- 4Bytes).
c. IP Address
IP address of the N-L20.
d. Input and Output Assembly Instance
100 and 101 respectively (fixed)
e. Input and Output Size
Assembly size, Input and Output should be the SAME for both
Suggested Sizes:
1. DINT 100, 100
2. INT 200, 200
3. SINT 400, 400
5
Chapter
TRNSMITTING SETTINGS AND MONITORING
6 READING DATA
Set the CPU mode key of the CPU unit to “REM” (center position).
Select [Communications] ➞ [Who Active] from the RSLogix5000 window.
When the sample code is read, the data read is stored in the “Result
Data” area as shown below.
In this example, select [USB] ➞ [1756-EN2T] ➞ [Backplane]
➞ [1756-L61], and execute[Download].
6
BarcodeReader.com
http://www.barcodereader.com/
You can download technical documents useful for BL/SR/HR introduction
and operation.
Download the latest manual from this Web page.
Copyright (c) 2015 KEYENCE CORPORATION. All rights reserved. 058127E 1086-2 058127 Printed in Japan