Professional Documents
Culture Documents
17 - I56-1463-006 FDM-1 Dual Monitor Module
17 - I56-1463-006 FDM-1 Dual Monitor Module
I56-1169-013
SIGNAL LINE CIRCUIT (SLC) WIRES MUST BE SUPERVISED PER NFPA
32 VDC MAX.
ALL WIRING SHOWN IS SUPERVISED. TWISTED PAIR
CONNECT
CONNECT MODULES
MODULES TO LISTED
TO LISTED COMPATIBLE
COMPATIBLE
IS RECOMMENDED NOTIFIER CONTROL PANELS
ONLYONLY
TO NEXT )–(
)+(
NOTIFIER
)–(
CONTROL PANELS
FROM PANEL OR
FCM-1 Supervised Control Module
)+( PREVIOUS DEVICE
DEVICE
Installation And Maintenance Instructions
SPEAKER SWITCHING CIRCUIT - NFPA STYLE W CONTROL
SPEAKERS MUST BE LISTED FOR FIRE PROTECTION. REFER MODULE Specifications
AUDIO CIRCUIT
TO THE RELAY CONTACT RATING TABLE FOR MAXIMUM LOAD.
DO NOT LOOP WIRE AROUND TERMINALS Normal Operating Voltage: 15 to 32 VDC
3 & 4. BREAK WIRE TO ENSURE
9
8 4
5
67 8 9
10
11
0
1
)–( SUPERVISION OF CONNECTIONS. Maximum Current Draw: 6.5 mA (LED on)
)–( )–( 3 12
)+(
Average Operating Current: 375µA (LED flashing - in group poll mode) 350µA (LED of flashing - in direct poll
2 13
47 K EOL
7
6
TENS
4
5
1 0 15 14
6789
2
3
)–( AUDIO AMPLIFIER, 70.7 Vrms MAX.
RESISTOR
3
5 4
USE ONLY MODELS AA-30, AA100 OR AA-120. AMPLIFIER
mode)
2
)+(
10
ONES
LOOP ADDRESS
Figure 6. Typical fault tolerant wiring for speaker supervision and switching, NFPA Style Z: Before Installing
This information is included as a quick reference installation guide. Refer to the control panel installation manual for
detailed system information. If the modules will be installed in an existing operational system, inform the operator and
SIGNAL LINE CIRCUIT (SLC) WIRES MUST BE SUPERVISED PER NFPA local authority that the system will be temporarily out of service. Disconnect power to the control panel before installing
32 VDC MAX.
ALL WIRING SHOWN IS SUPERVISED. TWISTED PAIR
the modules.
CONNECT MODULES TO LISTED COMPATIBLE
IS RECOMMENDED
NOTIFIER CONTROL PANELS ONLY NOTICE: This manual should be left with the owner/user of this equipment.
TO NEXT )–( )–(
DEVICE
)+( FROM PANEL OR
)+( PREVIOUS DEVICE General Description
FCM-1 Supervised Control Modules are intended for use in intelligent, two-wire systems, where the individual address of
CONTROL
SPEAKERS MUST BE LISTED FOR FIRE PROTECTION. REFER MODULE each module is selected using the built-in rotary switches. This module is used to switch an external power supply, which
AUDIO CIRCUIT
TO THE RELAY CONTACT RATING TABLE FOR MAXIMUM LOAD.
DO NOT LOOP WIRE AROUND TERMINALS
can be a DC power supply or an audio amplifier (up to 80 VRMS), to notification appliances. It also supervises the wiring
9
5
67 8 9
10
0
)–(
3 & 4. BREAK WIRE TO ENSURE
SUPERVISION OF CONNECTIONS.
to the connected loads and reports their status to the panel as NORMAL, OPEN, or SHORT CIRCUIT. The FCM-1 has two
47 K EOL 8 4 11 1
)+(
pairs of output termination points available for fault-tolerant wiring and a panel-controlled LED indicator. This module can
3 12
2 13
7 2
)–(
1 0 15 14
WARNING
All relay switch contacts are shipped in the standby state (open) state, but may have transferred to the activated (closed)
state during shipping. To ensure that the switch contacts are in their correct state, modules must be made to communicate
with the panel before connecting circuits controlled by the module.
Figure 4. Typical fault tolerant notification appliance circuit configuration, NFPA Style Z:
C0218-00 C0458-00
J1 UNDER LABEL
ALL WIRING SHOWN IS SUPERVISED SIGNAL LINE CIRCUIT (SLC)
AND POWER LIMITED 32 VDC MAX. CONNECT MODULES TO LISTED COMPATIBLE
TWISTED PAIR NOTIFIER CONTROL PANELS ONLY
IS RECOMMENDED
Figure 2A. Module mounting with barrier: Figure 2B: TO NEXT
)–( )–(
FROM PANEL OR
)+( )+(
DEVICE PREVIOUS DEVICE
CONTROL
MODULE
24 VDC CIRCUIT
MODULE POLARITIES ARE DO NOT LOOP WIRE ON TERMINALS
SHOWN IN ALARM 3 & 4. BREAK WIRE RUN TO PROVIDE
0
9
8 4
5
67 8 9
10
11 1 )–( SUPERVISION OF CONNECTIONS.
3 12
9 7
2 13
1 0 15 14 2 )+(
EOL RESISTOR IS )–(
TENS
8 4 5 6 78 )–( )–( 6 5
6789
3 24 VDC POWER SUPPLY
7T 3 4
)+(
9
INTERNAL AT
3
6 EN 21
S 0
10 0 5 2 4
ISOLATED, REGULATED, POWER
LO 1 11 10
OP 5 1
4 5 6 7 8 5 14 13 2 1 ONES
ON 2
ES 1
3
9 2 TERMINALS 8 & 9 LOOP ADDRESS
LIMITED PER NFPA 70.
0 3
AD
DR 4 LISTED FOR FIRE PROTECTION WITH
ES
S
BATTERY BACKUP.
)+( )+(
UL LISTED EOL RELAY
8
9 SHOWN ENERGIZED TO NEXT CONTROL MODULE OR END-OF-LINE-RELAY.
24VDC COIL
4 5 6 78
7
ONE RELAY REQUIRED FOR EACH CIRCUIT.
3
9
6 TEN 2
S 10 10 0
LO 1211
OP 5 3
15
4 5 6 7 8 14 13 1
2
EOLR-1 SOME CONTROL PANELS HAVE RELAY BUILT IN AND
ON 2 9
ES 1
0 3
AD
DR 4
ES
NOTIFIER MANUAL.
ISOLATED
QUADRANT
C0821-01
C0219-00
C0217-00