Professional Documents
Culture Documents
Data sheet
107755_en_00 © PHOENIX CONTACT 2021-02-23
1 Description
With this device you can control I/P converters, control Features
valves, and displays.
– Input and output signal range 0 mA ... 20 mA or
HART data protocols can be transmitted bidirectionally. 4 mA ... 20 mA
Electrically isolated 0...20 mA or 4...20 mA standard analog – Screw connection available
signals are available on the input and output sides.
This document is valid for the products listed in the “Ordering data”.
MINI MCR-SL-IDS-I-I
2 Table of contents
1 Description .............................................................................................................................. 1
2 Table of contents ..................................................................................................................... 2
3 Ordering data .......................................................................................................................... 3
4 Technical data ......................................................................................................................... 4
5 Safety regulations and installation notes.................................................................................. 6
5.1 Installation notes ................................................................................................................. 6
5.2 UL notes............................................................................................................................ 6
6 Installation ............................................................................................................................... 7
6.1 Connection notes ................................................................................................................ 7
6.2 Structure ........................................................................................................................... 7
6.3 Block diagram ..................................................................................................................... 7
6.4 Power supply ...................................................................................................................... 7
6.5 Mounting ........................................................................................................................... 8
6.6 Connection of the cables ....................................................................................................... 8
3 Ordering data
4 Technical data
Input
Number of inputs 1
Current input signal 4 mA ... 20 mA
0 mA ... 20 mA
Max. current input signal 20 mA
Input voltage limitation < 2 V (20 mA)
Output
Output description Current output
Number of outputs 1
Current output signal 4 mA ... 20 mA
0 mA ... 20 mA
Ripple < 20 mVrms
Load/output load current output ≤ 800 Ω (at 20 mA)
Supply
Nominal supply voltage 24 V DC
Supply voltage range 19.2 V DC ... 30 V DC (The DIN rail bus connector (ME 6,2
TBUS-2 1,5/5-ST-3,81 GN, Order No. 2869728) can be used to
bridge the supply voltage. It can be snapped onto a 35 mm DIN
rail according to EN 60715))
Power consumption < 600 mW (at 24 V DC)
General data
HART function Yes
Limit frequency (3 dB) > 175 Hz
Measuring principle Signal isolator
Maximum transmission error ≤ 0.1 % (of final value)
Temperature coefficient, typical < 0.01 %/K
Maximum temperature coefficient < 0.01 %/K
Step response (10-90%) < 2 ms
Communication HART specification
Electrical isolation Basic insulation according to EN 61010
Overvoltage category II
Mounting position any
Degree of protection IP20
Degree of pollution 2
Rated insulation voltage 50 V AC/DC
Test voltage, input/output/supply 1.5 kV (50 Hz, 1 min.)
Dimensions W/H/D 6.2 mm / 93.1 mm / 101.2 mm
Type of housing PBT green
Connection data
Connection method Screw connection
Conductor cross section solid 0.2 mm² ... 2.5 mm²
Conductor cross section flexible 0.2 mm² ... 2.5 mm²
Conductor cross section AWG 26 ... 12
Stripping length 12 mm
Ambient conditions
Ambient temperature (operation) -20 °C ... 60 °C
Ambient temperature (storage/transport) -40 °C ... 85 °C
Permissible humidity (operation) 5 % ... 95 % (non-condensing)
Maximum altitude for use above sea level ≤ 2000 m
Conformance/Approvals
CE CE-compliant
UL, USA/Canada UL 508 Listed
Class I, Div. 2, Groups A, B, C, D T4
Class I, Zone 2, Group IIC
Shipbuilding approval (DNV GL TAA000020N)
Temperature B
Humidity B
Vibration B
EMC A
Enclosure Required protection according to the Rules shall be provided
upon installation on board
5.2 UL notes
+24V +24V
Figure 1 Structure + 3 7 +
GND 3 GND 3
2 - 4 8 -
1
3
Warning – Do n ot seperate
an
y +24V
erm
, G -I-I
mb
erg IDS 7
- 7 GND 3
5 Blo R-SL 5 5
82 0 rt
when energized
C
32 I M .: 29 ma
NOTE:
T
–20 OU
4 Tamb
IN
I
ire
2-w
1
D 7
GN +
individual modules.
3
D
GN
-
8 2
ne
Zo
4V 3
+2 ND
G
5
7 Supply via the module
o.
ial N
Ser
Where the total current consumption of the aligned modules
6 does not exceed 400 mA, the power can be supplied directly
at the connection terminal blocks of the module.
1. Output: Standard signals A 400 mA fuse should be connected upstream.
2. Cover
3. Groove for ZBF 6 zack marker strip Supply via a power terminal block
4. Input: Standard signals The MINI MCR-SL-PTB power terminal block (Order No.
5. Supply voltage 2864134) of the same shape is used to feed in the supply
voltage to the DIN rail connector.
6. Connection for DIN rail connector
7. Universal snap-on foot for EN DIN rails A 2 A fuse should be connected upstream.
approx. +0,5mA
C Analog signal 0
D E approx. -0,5mA
1200 Hz 2200 Hz
"1" "0"
B 12 mm
A 0,5-0,6 Nm
5-7 lb In
• Insert the wire into the corresponding connection
terminal block.
• Use a screwdriver to tighten the screw in the opening
above the connection terminal block.
107755_en_00 PHOENIX CONTACT GmbH & Co. KG • 32823 Blomberg • Germany 8/8
phoenixcontact.com