Professional Documents
Culture Documents
Search...
1.
1. You have a router with the following IP addresses:
ether1: 10.40.1.1/24
ether2: 10.250.1.1/30
ether3: 10.251.1.1/30
wlan1: 10.50.1.1/30
wlan2: 10.50.2.1/30
You have a customer directly connected to ether2, and another customer directly connected to ether3. Your wireless radios are used for wireless
connectivity to two different towers, and ether1 goes to another wireless access point for other subscribers. You need all of the subnets
distributed across your OSPF Network
You need to configure OSPF to talk on this router, what would be the best configuration.
00:16:21
Save progress
A. Set Ethernet 1, 2, and 3 to passive mode
C. Set Distribute-Connected=yes
E. set distribute-default=always-type-1
I. set distribute-state=yes
2.
2. It is possible to filter ospf routes within a single ospf area
true
3. There
3. There is no way to establish OSPF adjacency when the link doesn\'t support multicast traffic.
false
false
4. When
When using routing option
option 'check-gate
'check-gatew
way=ping' after how
how many timeouts
timeouts is gateway considered unreachable:
A. 4
B. 2
C. 1
D. 3
5. PPPoE
5. PPPoE server only works within one Ethernet broadcast domain that it is connected to. If there is a router between server and end-user host,
it will not be able to create PPPoE tunnel to that PPPoE server.
true
6. If
6. If route type is 'blackhole', then packets to the destination network are going to be
D. dropped on this router and ICMP message will be sent back to the source
7.
7. Which are correct ECMP routes (mark all that apply):
B. dst-addr=0.0.0.0/0 gateway=10.1.1.1,10.1.1.1,10.2.2.2
C. dst-addr=0.0.0.0/0 gateway=10.1.1.1,10.1.1.1
D. dst-addr=0.0.0.0/0 gateway=10.1.1.1
8.
8. When using routing option 'check-gateway=ping' what is the ICMP echo request interval (in seconds)?
A. 20s
B. 30s
C. 10s
file://
file:///me
/media
dia/Da
/Data/
ta/T
Trainin
raining/M
g/MTC
TCRE%
RE%20T
20Trainin
raining%2
g%20Ma
0Mater
terial
ials/M
s/MTC
TCRE2
RE2/Mi
/Mikro
kroTi
Tik%2
k%20R
0Rout
outers
ers%20
%20and
and%20
%20Wi
Wirel
reless
ess.ht
.htm
m 1/4
7/28/2016 MikroTik Routers and Wireless
D. 60s
9. A MikroTik system administrator implemented OSPF Routing protocol in the network. But realized that he has a static route on the routers.
What can be done to make the static route work as a failover whenever the dynamic routing protocol fails.
A. He should use "netwatch" to t rigger static routes whenever OSPF fails
B. He should manually disable the static routes and enable them whenever OSPF fails
C. Delete all static routes because there is no way for it to work with OSPF
10. Consider the following diagram. We want to communicate from a device on LAN1 to a device on LAN2. Assuming that all necessary
configurations are already included on R2, which of the following configurations in R1 would enable this communication?
11. New area OSPF \"area1\" has been created. What could be used as a valid area id?
A. 0.0.0.1
B. 0.0.0.0
C. 1.2.3.4
12. In OSPF, router can become the DR (Designated Router) only when the priority on it\\\'s interface is set to a value of zero
false
B. will have two vlan tags added to ethernet header - "101" and "102"
C. Wrong configuration because it is not possible to have a vlan over another vlan
A. 5.6.6.6
B. 5.5.5.5
D. both - half of the traffic will be routed through one gateway, half through the other
16. There can be more than one PPPoE server in a single broadcast domain:
true
0 dst-address=10.0.0.0/24 gateway=10.1.5.126
1 dst-address=10.1.5.0/24 gateway=10.1.1.1
2 dst-address=10.1.0.0/24 gateway=25.1.1.1
3 dst-address=10.1.5.0/25 gateway=10.1.1.2
Which gateway will be used for a packet with destination address 10.1.5.126?
file:///media/Data/Training/MTCRE%20Training%20Materials/MTCRE2/MikroTik%20Routers%20and%20Wireless.htm 2/4
7/28/2016 MikroTik Routers and Wireless
A. 25.1.1.1
B. 10.1.1.1
C. 10.1.1.2
D. 10.1.5.126
A. 192.168.0.4
B. 192.168.0.2
C. 192.168.0.1
D. 192.168.0.3
19. The OSPF network is configured as on the attached figure. Each of the links has cost sets as on the figure. If we configure redistribution of
default route on router A with command:
A. 25
B. 35
C. 26
D. 5
23. VLAN is an implementation of the 802.1Q VLAN protocol by the MikroTik RouterOS. It allows you to have multiple Virtual LANs on a single
ethernet or wireless interface, giving the ability to segregate LANs efficiently.
How many different vlans are possible on a single ethernet port?
A. 4095
B. 63
C. 4096
D. only one
true
25. RouterOS device has acquired an IP address from an ISP using DHCP client. The same router is used for assigning IP addresses to local users
using DHCP server, masquerade rule is configured properly. Packets that are coming from the ISP have TTL=1. Select correct statement:
file:///media/Data/Training/MTCRE%20Training%20Materials/MTCRE2/MikroTik%20Routers%20and%20Wireless.htm 3/4
7/28/2016 MikroTik Routers and Wireless
C. Router does not have access to the Internet, but clients have
Finish
file:///media/Data/Training/MTCRE%20Training%20Materials/MTCRE2/MikroTik%20Routers%20and%20Wireless.htm 4/4