Professional Documents
Culture Documents
Seats
Specifications
Torque
Description Value
Bolt - Front Seat to Body 40-50 Nm
Bolt - Seatback Assembly to Seat Cushion Assembly 40-50 Nm
Bolt - Striker to Body 19-25 Nm
cardiagn.com
V 2.0 481
Interior Fitting Seats
cardiagn.com
1. Lumbar Support Adjustment Handle 3. Seat Vertical Hand Wheel
2. Seatback Adjustment Hand Wheel 4. Seat Fore-and-Aft Handle
V 2.0 482
Seats Interior Fitting
Power Driver Seat Component Layout
cardiagn.com
1. Lumbar Support Adjustment Handle 3. Driver Seatback Adjustment Switch
2. Driver Seat Switch Set 4. Driver Seat Vertical and Fore-and-Aft Switch
V 2.0 483
Interior Fitting Seats
cardiagn.com
A = Hard Wire
1. Seat Fore-and-Aft Motor 4. Seat Adjustment Fuse 25 (30A)
2. Seat Vertical Motor 5. Driver Seat Switch Set
3. Seatback Adjustment Motor
V 2.0 484
Seats Interior Fitting
Description • Six-way power seat with the leather and side airbag (seat
Driver Seat position sliding forward/backward, reclining, seat height
and lumbar support adjustment). In addition, the centre
Depending on the different vehicle equipment and seat
position of the rear seat in this model is equipped with
exterior, the configuration of driver seat has 4 different levels
the headrest.
as follows:
Front Passenger Seat
• Advanced fabric 6-way manual seat (seat position sliding
forward/backward, reclining, seat height); The configurations of the front passenger seat in all models are
only four-way manual adjustment (the fore-and-aft adjustment
• Six-way manual seat with the leather (seat position
of the seat position and the reclining of the seatback). The
sliding forward/backward, reclining, seat height and
advanced configuration model is also equipped with the seat
lumbar support adjustment);
belt unfasten reminder and the side airbag. The storage box is
• Six-way power seat with the leather (seat position under the seat cushion of the passenger seat.
sliding forward/backward, reclining, seat height and
lumbar support adjustment);
cardiagn.com
V 2.0 485
Interior Fitting Seats
Operation by the handle located at the front of the seat. The adjusting
Manual Seat hand wheel on the side can adjust the seatback position.
Driver Seat Power Seat
The fore-and-aft position of the seat can be adjusted by the The driver power seat can be adjusted by using the driver
handle located at the front of the seat. The desired position seat switch box located at the seat outside trim panel. As
can be reached by lifting the handle. The seat is locked in the a result, the personal requirement can be satisfied. This
selected position when the handle is released. The second seat has the power adjustment modes, for example, moving
adjustment hand wheel located at the front of the seat cushion forward/backward, the change of the height and the inclination
outside trim panel is used to adjust the height of the seat. The of the seatback and so on. The lumbar support adjustment is
seat height can be raised and lowered by repeatedly turning always controlled by hand. The seat can be adjusted when the
this hand wheel clockwise or counterclockwise. The third wireless key is turned toAUX or ignition position. The power
adjusting hand wheel behind the vertical adjusting hand wheel is supplied to the power seat through the fuse 25 (30 A) in the
is used to adjust the inclination of the seatback. The inclination engine bay. The axial movement of the seat can be controlled
of the seatback can be adjusted by repeatedly turning this by the driver seat switch box located at the seat outside trim
hand wheel clockwise or counterclockwise. There is a rotary panel. This switch box has a two-way switch which controls
handle located at the underneath of driver seatback outside the fore-and-aft tilt of the seatback and a four-way switch
for adjusting the lumbar support in the seatback. Turning the which controls the seat height and fore-and-aft position of
lumbar support adjusting handle clockwise could make the the seat. Each motor is powered by the 12V power source
cardiagn.com
lumbar back cushion softer, while turning counterclockwise from the switch box and grounds. Depending on the different
could make it harder. Turning this adjusting handle will pull adjustment requirements of the seat, the power is supplied
a cable connected to the lumbar support device with the to the selected motor and makes it operate. When the seat
edge. With the cable being pulled, the lumbar support device reaches its maximum adjustment position in each adjustment
deviates from the original position to make the lumbar back direction, the thermal protection cut switch will cut the power
cushion harder. supply automatically to protect the motor.
Front Passenger Seat
The adjustment mode of passenger seat is the same as the
driver seat. The seat can be adjusted forward and backward
V 2.0 486
Seats Interior Fitting
Service Procedures Warning: Always ensure that the SRS wire harness is
Front Seat arranged correctly. Be careful to avoid trapping or
pinching the SRS wire harness. DO NOT hang the
Warning: Before starting removing and repairing the SRS
connector loosely or keep the SRS components hanging
system, always remove the key from the ignition switch
down by the wire harness. Check for the points that are
and disconnect the vehicle battery for more than 10
easy worn.
minutes.
Removal 3. Connect the battery negative terminal.
1. If the seat can be adjusted, raise it upward sufficiently. 4. Secure the seat to the body, then fit the 2 new rear
retaining bolts and tighten to 40-50 Nm.
2. Move the seat backward sufficiently.
5. Move the seat backward sufficiently.
3. Unscrew the 2 bolts securing the front of the seat to
the body and dispose the bolts. 6. Fit the 2 new front retaining bolts and tighten to 40-50
Nm.
cardiagn.com
4. Move the seat forward sufficiently.
5. Unscrew the 2 bolts securing the rear of the seat to the
body and dispose the bolts.
V 2.0 487
Interior Fitting Seats
cardiagn.com
1. Position the seatback and connect the seat heater
connector. (If equipped)
2. Position the seat cushion assembly and the seatback
assembly, fit the 4 bolts and tighten to 40-50 Nm. 3. Remove the 2 headrest guides.
V 2.0 488
Seats Interior Fitting
6. Fit the front seatback assembly. Front Seat Cushion
Front Seatback Assembly
Removal
1. Remove the front seat belt buckle.
Front Seat Belt Buckle
2. Remove the outside trim panel.
Driver Seat Outside Trim Panel
3. Loosen the cable and the J-clip securing the seatback
fascia to the seat frame.
4. Unscrew the 4 bolts connecting the seat cushion
assembly to the seatback assembly.
5. Disconnect the 2 seat heater connectors. (If equipped)
6. Remove the seat cushion assembly.
Refit
1. Position the seat cushion and connect the seat heater
connector. (If equipped)
cardiagn.com
2. Fit the 4 bolts connecting the seat cushion assembly to
the seatback assembly and tighten to 40-50 Nm.
3. Secure the seatback fascia to the seat frame with the
cable and C-ring.
4. Fit the outside trim panel.
V 2.0 489
Interior Fitting Seats
cardiagn.com
3. Fit the front seat cushion assembly.
3. Manual driver seat: remove the seatback adjustment
Front Seat Cushion hand wheel.
V 2.0 490
Seats Interior Fitting
Front Power Seat Switch Set
Removal
1. Remove the driver seat outside trim panel assembly.
Driver Seat Outside Trim Panel
2. Unscrew the screw securing the outside trim panel to
the seat.
cardiagn.com
3. Release the 2 adjustment switch buttons and remove
the switch panel.
4. Unscrew the 2 screws securing the combination switch
to the outside panel and remove the combination
switch.
Refit
1. Position the outside trim panel, then fit the 3 set screws
and tighten them.
2. Position the front trim panel, then fit a set screw and
5. Disconnect the connector of the combination switch,
tighten it.
and remove the combination switch.
3. Manual driver seat: fit the seatback adjustment hand
Refit
wheel.
1. Fit the combination switch to the outside panel and
4. Lift up the seatback.
secure it with the screw.
2. Connect the combination switch connector.
3. Fit the adjustment switch button and the panel to the
combination switch.
4. Fit the driver seat outside trim panel assembly.
Driver Seat Outside Trim Panel
V 2.0 491
Interior Fitting Seats
cardiagn.com
3. Mark the position of the seatback hinge shackle.
3. After the front of the seat cushion is lifted, push the 4. Unscrew the 2 bolts securing the hinge to the body.
seat cushion backward and lift it until the seat cushion
is released from the 2 bushings.
Refit
1. Make sure that the belt is on the correct route and the
position of the seat cushion is correct.
2. Place the rear of the seat cushion into the 2 bushings
on the body.
3. Fit the front seat cushion into the steel wire snap fit.
4. Draw out the seat belt buckle from the seat belt
through hole on the seat cushion.
Refit
1. Position the hinge on the body, then fit the bolt and
tighten to 19-25 Nm.
2. Fit the trim panel to the body.
3. Close the rear seatback assembly.
V 2.0 492