Professional Documents
Culture Documents
Service Guide
PRINTED IN TAIWAN
Disassembly Requirements
To disassemble the computer, you need the following tools:
• Wrist grounding strap and conductive mat for preventing electrostatic discharge
• Flat screwdriver
• Philips screwdriver
• Hex screwdriver
• Plastic flat screwdriver
• Plastic tweezers
NOTE: The screws for the different components vary in size. During the disassembly process, group the
screws with the corresponding components to avoid mismatch when putting back the components.
Chapter 3 27
Downloaded from www.Manualslib.com manuals search engine
General Information
Pre-disassembly Instructions
Before proceeding with the disassembly procedure, make sure that you do the following:
1. Turn off the power to the system and all peripherals.
2. Unplug the AC adapter and all power and signal cables from the system.
Disassembly Process
The disassembly process is divided into the following stages:
• External module disassembly
• Main unit disassembly
• LCD module disassembly
The flowcharts provided in the succeeding disassembly sections illustrate the entire disassembly sequence.
Observe the order of the sequence to avoid damage to any of the hardware components. For example, if you
want to remove the main board, you must first remove the keyboard, then disassemble the inside assembly
frame in that order.
Main Screw List
28 Chapter 3
Chapter 3 29
3. Slide the battery release latch to the release position to pop out the battery pack, then remove the battery
pack from the main unit.
Note: Battery has been highlighted with the yellow circle as above image shows. Please detach the
battery and follow the local regulations for disposal.
30 Chapter 3
Chapter 3 31
4. Use a flat screwdriver to pry open the back cover and detach it from the lower case.
32 Chapter 3
Chapter 3 33
6. Lift the hard disk drive module and remove it from the hard disk drive bay.
NOTE: To prevent damage to device, avoid pressing down on it or placing heavy objects on top of it.
34 Chapter 3
Chapter 3 35
7. Disconnect the blue antenna cable from AUX connector and the yellow antenna cable from Main
connector on the wireless WAN module.
36 Chapter 3
NOTE: When attaching the antenna back to the wireless WAN module, make sure the cable are arranged
properly.
Chapter 3 37
9. Disconnect the black antenna cable from MAIN connector and the white antenna cable from AUX
connector on the WLAN module.
38 Chapter 3
NOTE: When attaching the antenna back to the WLAN module, make sure the cable are arranged properly.
Chapter 3 39
10. Remove the one screw (B) securing the ODD bracket to the ODD module.
40 Chapter 3
Chapter 3 41
Screw List
42 Chapter 3
Chapter 3 43
44 Chapter 3
12. Detach the speaker cable from its connector on the main board.
13. Detach the touchpad cable from its connector on the main board.
Chapter 3 45
15. Remove the five screws (B) from the lower case.
46 Chapter 3
17. Gently detach the upper case from the lower case. Remove the upper case.
Chapter 3 47
12. Detach the LCD cable from its connector and tape on the main board.
48 Chapter 3
14. Release the microphone cable, WWAN and WLAN antennas from the latches and tapes.
Chapter 3 49
16. Carefully remove the LCD module from the base unit.
NOTE: When connecting the cable back to the unit, please note that the cable should be routed well.
50 Chapter 3
12. Pry to loosen the touchpad board and detach it from the upper case.
WARNING: The touchpad board is glued to the upper case, only remove the touchpad board if it is defective.
Note: Circuit board >10 cm² has been highlighted with the yellow rectangle as above image shows.
Please detach the Circuit boards and follow local regulations for disposal.
Chapter 3 51
12. Release the latch and disconnect the the power cable from the power board.
52 Chapter 3
Chapter 3 53
54 Chapter 3
14. Remove the USB board module from the lower case.
Chapter 3 55
14. Release the bluetooth cable from the tape and latches.
56 Chapter 3
Note: RTC battery has been highlighted with the yellow circle as shown in the figure above. Please
detach the RTC battery and follow local regulations for disposal.
Note: Circuit boards >10 cm² has been highlighted with the yellow rectangle as above image shows.
Please detach the Circuit boards and follow local regulations for disposal.
Chapter 3 57
58 Chapter 3
Chapter 3 59
17. Remove the six screws securing the heatsink module in the order shown.
NOTE: The Discrete system may be shipped with NVIDIA N11PGE1 VRAM HYNIX Graphic DDRIII 800 1GB or NVIDIA
N11MGE1 VRAM Samsung Graphic DDRIII 800 512MB.
60 Chapter 3
Chapter 3 61
62 Chapter 3
Chapter 3 63
Screw List
64 Chapter 3
13. Remove the two screws (A) from the LCD module as shown.
Chapter 3 65
66 Chapter 3
15. Remove the web camera module from the LCD module back cover.
NOTE: The web camera module is glued to the LCD module back cover, only remove the web camera
module if it is defective.
Chapter 3 67
68 Chapter 3
Chapter 3 69
70 Chapter 3
Chapter 3 71
72 Chapter 3
Chapter 3 73
NOTE: There is no need to remove the antenna unless you really need to replace it.
74 Chapter 3