Professional Documents
Culture Documents
com
E-mail:http://www.LGEservice.com/techsup.html
COLOR MONITOR
SERVICE MANUAL
CHASSIS NO. : LM57D
MODEL: L1732P (L1732P-SFR.A**XQP)
L1932P (L1932P-SFR.A**XQP)
( ) **Same model for Service
CAUTION
BEFORE SERVICING THE UNIT,
READ THE SAFETY PRECAUTIONS IN THIS MANUAL.
SPECIFICATIONS
1. LCD CHARACTERISTICS 4. Max. Resolution
Type : TFT Color LCD Module D-sub Analog : 1280 x 1024@75Hz
Active Display Area : 17 inch-L1732P Digital : 1280 x 1024@60Hz
: 19 inch-L1932P
Pixel Pitch : 0.264 (H) x 0.264 (V)-L1732P 5. POWER SUPPLY
: 0.294 (H) x 0.294 (V)-L1932P 5-1. Power : AC 100~240V, 50/60Hz , 0.6A
Color Depth : 16.2M colors
Size : 358.5 (H) x 296.5 (V) x 17(D)-L1732P 5-2. Power Consumption
: 396 (H) x 324 (V) x 16.5(D)-L1932P
Electrical Interface : LVDS MODE H/V SYNC VIDEO POWER CONSUMPTION LED COLOR
Surface Treatment : Hard-coating(3H), Anti-Glare less than 35 W-L1732P
Operating Mode : Normally White, Transmissive mode POWER ON (NORMAL) ON/ON ACTIVE BLUE
Backlight Unit : 4-CCFL less than 39 W-L1932P
STAND-BY OFF/ON OFF less than 1 W AMBER
2. OPTICAL CHARACTERISTICS
2-1. Viewing Angle by Contrast Ratio ≥ 10 SUSPEND ON/OFF OFF less than 1 W AMBER
L1732P DPMS OFF OFF/OFF OFF less than 1 W AMBER
Left : -70° min., -80°(Typ) Right : +70° min., +80°(Typ)
Top : +60° min., +75°(Typ) Bottom : -70° min., -85°(Typ) POWER S/W OFF - - less than 1 W OFF
L1932P
Left : -75° min., -88°(Typ) Right : +75° min., +88°(Typ) 6. ENVIRONMENT
Top : +70° min., +85°(Typ) Bottom : -70° min., -85°(Typ) 6-1. Operating Temperature : 10°C~35°C (50°F~95°F)
(Ambient)
2-2. Luminance : 200(min), 250(Typ)-6500K 6-2. Relative Humidity : 10%~80% (Non-condensing)
: 150(min), 200(Typ)-9300K 6-3. MTBF : 50,000 HRS with 90% Confidence
Lamp Life : 50,000 Hours(Min)
2-3. Contrast Ratio : 500(min), 700(Typ)-L1732P
450(min), 700(Typ)-L1932P 7. DIMENSIONS (with TILT/SWIVEL)
1400(DFC applied) L1732P
Width : 390 mm (16.93'')
3. SIGNAL (Refer to the Timing Chart) Depth : 242 mm (9.13'')
3-1. Sync Signal Height : 430 mm (16.89'')
• Type : Separate Sync, Composite, Digital,
SOG (Sync On Green) L1932P
Width : 430 mm (16.93'')
3-2. Video Input Signal Depth : 242 mm (9.13'')
1) Type : R, G, B Analog Height : 445 mm (16.89'')
2) Voltage Level : 0~0.71 V
a) Color 0, 0 : 0 Vp-p 8. WEIGHT (with TILT/SWIVEL)
b) Color 7, 0 : 0.467Vp-p L1732P
c) Color 15, 0 : 0.714Vp-p Net. Weight : 5.5 kg (10.14 lbs)
3) Input Impedance : 75Ω Gross Weight : 6.5 kg (11.25 lbs)
L1932P
3-3. Operating Frequency Net. Weight : 6.4 kg (10.14 lbs)
Horizontal : 30 ~ 83kHz (Analog) Gross Weight : 7.8 kg (11.25 lbs)
: 30 ~ 71kHz (Digital)
Vertical : 56 ~ 75Hz
-2-
PRECAUTION
WARNING FOR THE SAFETY-RELATED COMPONENT. WARNING
• There are some special components used in LCD BE CAREFUL ELECTRIC SHOCK !
monitor that are important for safety. These parts are
• If you want to replace with the new backlight (CCFL) or
marked on the schematic diagram and the
inverter circuit, must disconnect the AC adapter
replacement parts list. It is essential that these critical
because high voltage appears at inverter circuit about
parts should be replaced with the manufacturer’s
650Vrms.
specified parts to prevent electric shock, fire or other
hazard.
• Handle with care wires or connectors of the inverter
• Do not modify original design without obtaining written circuit. If the wires are pressed cause short and may
permission from manufacturer or you will void the burn or take fire.
original parts and labor guarantee.
TAKE CARE DURING HANDLING THE LCD MODULE Leakage Current Hot Check Circuit
WITH BACKLIGHT UNIT.
AC Volt-meter
• Must mount the module using mounting holes arranged
in four corners.
• Do not press on the panel, edge of the frame strongly
or electric shock as this will result in damage to the Good Earth Ground
screen. such as WATER PIPE,
To Instrument's CONDUIT etc.
• Do not scratch or press on the panel with any sharp exposed
objects, such as pencil or pen as this may result in METALLIC PARTS
damage to the panel.
• Protect the module from the ESD as it may damage the 1.5 Kohm/10W
electronic circuit (C-MOS).
• Make certain that treatment person’s body are
grounded through wrist band.
• Do not leave the module in high temperature and in
areas of high humidity for a long time.
• The module not be exposed to the direct sunlight.
• Avoid contact with water as it may a short circuit within
the module.
• If the surface of panel become dirty, please wipe it off
with a softmaterial. (Cleaning with a dirty or rough cloth
may damage the panel.)
CAUTION
Please use only a plastic screwdriver to protect yourself
from shock hazard during service operation.
-3-
SERVICING PRECAUTIONS
CAUTION: Before servicing receivers covered by this 9. Use with this receiver only the test fixtures specified in
service manual and its supplements and addenda, read this service manual.
and follow the SAFETY PRECAUTIONS on page 3 of this CAUTION: Do not connect the test fixture ground strap
publication. to any heat sink in this receiver.
NOTE: If unforeseen circumstances create conflict
between the following servicing precautions and any of the Electrostatically Sensitive (ES) Devices
safety precautions on page 3 of this publication, always Some semiconductor (solid-state) devices can be
follow the safety precautions. Remember: Safety First. damaged easily by static electricity. Such components
commonly are called Electrostatically Sensitive (ES)
General Servicing Precautions Devices. Examples of typical ES devices are integrated
1. Always unplug the receiver AC power cord from the AC circuits and some field-effect transistors and
power source before; semiconductor "chip" components. The following
a. Removing or reinstalling any component, circuit techniques should be used to help reduce the incidence of
board module or any other receiver assembly. component damage caused by static by static electricity.
b. Disconnecting or reconnecting any receiver electrical 1. Immediately before handling any semiconductor
plug or other electrical connection. component or semiconductor-equipped assembly, drain
c. Connecting a test substitute in parallel with an off any electrostatic charge on your body by touching a
electrolytic capacitor in the receiver. known earth ground. Alternatively, obtain and wear a
CAUTION: A wrong part substitution or incorrect commercially available discharging wrist strap device,
polarity installation of electrolytic capacitors may which should be removed to prevent potential shock
result in an explosion hazard. reasons prior to applying power to the unit under test.
d. Discharging the picture tube anode. 2. After removing an electrical assembly equipped with
2. Test high voltage only by measuring it with an ES devices, place the assembly on a conductive
appropriate high voltage meter or other voltage surface such as aluminum foil, to prevent electrostatic
measuring device (DVM, FETVOM, etc) equipped with charge buildup or exposure of the assembly.
a suitable high voltage probe. 3. Use only a grounded-tip soldering iron to solder or
Do not test high voltage by "drawing an arc". unsolder ES devices.
3. Discharge the picture tube anode only by (a) first 4. Use only an anti-static type solder removal device.
connecting one end of an insulated clip lead to the Some solder removal devices not classified as "anti-
degaussing or kine aquadag grounding system shield static" can generate electrical charges sufficient to
at the point where the picture tube socket ground lead damage ES devices.
is connected, and then (b) touch the other end of the 5. Do not use freon-propelled chemicals. These can
insulated clip lead to the picture tube anode button, generate electrical charges sufficient to damage ES
using an insulating handle to avoid personal contact devices.
with high voltage. 6. Do not remove a replacement ES device from its
4. Do not spray chemicals on or near this receiver or any protective package until immediately before you are
of its assemblies. ready to install it. (Most replacement ES devices are
5. Unless specified otherwise in this service manual, packaged with leads electrically shorted together by
clean electrical contacts only by applying the following conductive foam, aluminum foil or comparable
mixture to the contacts with a pipe cleaner, cotton- conductive material).
tipped stick or comparable non-abrasive applicator; 7. Immediately before removing the protective material
10% (by volume) Acetone and 90% (by volume) from the leads of a replacement ES device, touch the
isopropyl alcohol (90%-99% strength) protective material to the chassis or circuit assembly
CAUTION: This is a flammable mixture. into which the device will be installed.
Unless specified otherwise in this service manual, CAUTION: Be sure no power is applied to the chassis
lubrication of contacts in not required. or circuit, and observe all other safety precautions.
6. Do not defeat any plug/socket B+ voltage interlocks 8. Minimize bodily motions when handling unpackaged
with which receivers covered by this service manual replacement ES devices. (Otherwise harmless motion
might be equipped. such as the brushing together of your clothes fabric or
7. Do not apply AC power to this instrument and/or any of the lifting of your foot from a carpeted floor can
its electrical assemblies unless all solid-state device generate static electricity sufficient to damage an ES
heat sinks are correctly installed. device.)
8. Always connect the test receiver ground lead to the
receiver chassis ground before connecting the test
receiver positive lead.
Always remove the test receiver ground lead last.
-4-
General Soldering Guidelines Replacement
1. Use a grounded-tip, low-wattage soldering iron and 1. Carefully insert the replacement IC in the circuit board.
appropriate tip size and shape that will maintain tip 2. Carefully bend each IC lead against the circuit foil pad
temperature within the range or 500。F to 600。F. and solder it.
2. Use an appropriate gauge of RMA resin-core solder 3. Clean the soldered areas with a small wire-bristle
composed of 60 parts tin/40 parts lead. brush. (It is not necessary to reapply acrylic coating to
3. Keep the soldering iron tip clean and well tinned. the areas).
4. Thoroughly clean the surfaces to be soldered. Use a
mall wire-bristle (0.5 inch, or 1.25cm) brush with a "Small-Signal" Discrete Transistor
metal handle. Removal/Replacement
Do not use freon-propelled spray-on cleaners. 1. Remove the defective transistor by clipping its leads as
5. Use the following unsoldering technique close as possible to the component body.
a. Allow the soldering iron tip to reach normal 2. Bend into a "U" shape the end of each of three leads
temperature. remaining on the circuit board.
(500。F to 600。F) 3. Bend into a "U" shape the replacement transistor leads.
b. Heat the component lead until the solder melts. 4. Connect the replacement transistor leads to the
c. Quickly draw the melted solder with an anti-static, corresponding leads extending from the circuit board
suction-type solder removal device or with solder and crimp the "U" with long nose pliers to insure metal
braid. to metal contact then solder each connection.
CAUTION: Work quickly to avoid overheating the
circuitboard printed foil. Power Output, Transistor Device
6. Use the following soldering technique. Removal/Replacement
a. Allow the soldering iron tip to reach a normal 1. Heat and remove all solder from around the transistor
temperature (500。F to 600。F) leads.
b. First, hold the soldering iron tip and solder the strand 2. Remove the heat sink mounting screw (if so equipped).
against the component lead until the solder melts. 3. Carefully remove the transistor from the heat sink of the
circuit board.
c. Quickly move the soldering iron tip to the junction of 4. Insert new transistor in the circuit board.
the component lead and the printed circuit foil, and 5. Solder each transistor lead, and clip off excess lead.
hold it there only until the solder flows onto and 6. Replace heat sink.
around both the component lead and the foil.
CAUTION: Work quickly to avoid overheating the Diode Removal/Replacement
circuit board printed foil. 1. Remove defective diode by clipping its leads as close
d. Closely inspect the solder area and remove any as possible to diode body.
excess or splashed solder with a small wire-bristle 2. Bend the two remaining leads perpendicular y to the
brush. circuit board.
3. Observing diode polarity, wrap each lead of the new
IC Remove/Replacement diode around the corresponding lead on the circuit
Some chassis circuit boards have slotted holes (oblong) board.
through which the IC leads are inserted and then bent flat 4. Securely crimp each connection and solder it.
against the circuit foil. When holes are the slotted type, 5. Inspect (on the circuit board copper side) the solder
the following technique should be used to remove and joints of the two "original" leads. If they are not shiny,
replace the IC. When working with boards using the reheat them and if necessary, apply additional solder.
familiar round hole, use the standard technique as
outlined in paragraphs 5 and 6 above. Fuse and Conventional Resistor
Removal/Replacement
Removal 1. Clip each fuse or resistor lead at top of the circuit board
1. Desolder and straighten each IC lead in one operation hollow stake.
by gently prying up on the lead with the soldering iron 2. Securely crimp the leads of replacement component
tip as the solder melts. around notch at stake top.
2. Draw away the melted solder with an anti-static 3. Solder the connections.
suction-type solder removal device (or with solder CAUTION: Maintain original spacing between the
braid) before removing the IC. replaced component and adjacent components and the
circuit board to prevent excessive component
temperatures.
-5-
Circuit Board Foil Repair At Other Connections
Excessive heat applied to the copper foil of any printed Use the following technique to repair the defective copper
circuit board will weaken the adhesive that bonds the foil pattern at connections other than IC Pins. This technique
to the circuit board causing the foil to separate from or involves the installation of a jumper wire on the
"lift-off" the board. The following guidelines and component side of the circuit board.
procedures should be followed whenever this condition is 1. Remove the defective copper pattern with a sharp
encountered. knife.
Remove at least 1/4 inch of copper, to ensure that a
At IC Connections hazardous condition will not exist if the jumper wire
To repair a defective copper pattern at IC connections use opens.
the following procedure to install a jumper wire on the 2. Trace along the copper pattern from both sides of the
copper pattern side of the circuit board. (Use this pattern break and locate the nearest component that is
technique only on IC connections). directly connected to the affected copper pattern.
3. Connect insulated 20-gauge jumper wire from the lead
1. Carefully remove the damaged copper pattern with a of the nearest component on one side of the pattern
sharp knife. (Remove only as much copper as break to the lead of the nearest component on the
absolutely necessary). other side.
2. carefully scratch away the solder resist and acrylic Carefully crimp and solder the connections.
coating (if used) from the end of the remaining copper CAUTION: Be sure the insulated jumper wire is
pattern. dressed so the it does not touch components or sharp
3. Bend a small "U" in one end of a small gauge jumper edges.
wire and carefully crimp it around the IC pin. Solder the
IC connection.
4. Route the jumper wire along the path of the out-away
copper pattern and let it overlap the previously scraped
end of the good copper pattern. Solder the overlapped
area and clip off any excess jumper wire.
-6-
TIMING CHART
VIDEO
A
E
D
B
SYNC
C
-7-
DISASSEMBLY
#1 #2
#3 #4
-8-
5V LCD Module
5V 3.3V
LVDS
R,G,B (Low Voltage
differential Differential
3.3V Reg. 1.8V Reg. Signaling)
78D33 LD1117S18
3.3V 1.8V
TSUMO56WHJ
1.8V
FE2510MOH
including
-9-
M25P10
3.3V (ADC/LVDS/SCALER (flash memory)
12V 5V /INPUT SWITCHING
/TMDS/MICOM/ODC)
BLOCK DIAGRAM
AC Input LIPS
2. Power Part.
This part consists of the 3.3V regulator to convert power which is provided 12V,
5V in Power board and Micom
5V is provided for LCD panel.
Also, 5V is converted 3.3V by regulator and 3.3V is converted 1.8V by regulator.
Converted power is provided for IC in the main board.
3. MICOM Part.
This part consists of EEPROM IC which stores control data and the Micom.
The Micom distinguishes polarity and frequency of the H/V sync are supplied from signal cable.
The controlled data of each modes is stored in EEPROM.
- 10 -
LIPS Board Block Diagram
12V
50 ~ 60Hz
PRIMARY SECONDARY
Operation description_LIPS
1. EMI components.
This part contains of EMI components to comply with global marketing EMI standards like FCC,VCCI CISPR, the
circuit included a line-filter, across line capacitor and of course the primary protection fuse.
3. Energy Transfer.
This part function is for transfer the primary energy to secondary through a power transformer.
5. Photo-Coupler isolation.
This part function is to feed back the DC output changing status through a photo transistor to primary controller to
achieve the stabilized DC output voltage.
6. Signal collection.
This part function is to collect the any change from the DC output and feed back to the primary through photo
transistor.
- 11 -
ADJUSTMENT
Windows EDID V1.0 User Manual 2. EDID Read & Write
1) Run WinEDID.exe
Operating System: MS Windows 98, 2000, XP
Port Setup: Windows 98 => Don’t need setup
Windows 2000, XP => Need to Port Setup.
This program is available to LCD Monitor only.
1. Port Setup
a) Copy “UserPort.sys” file to
“c:\WINNT\system32\drivers” folder
b) Run Userport.exe
- 12 -
SERVICE OSD
1) Turn off the power switch at the front side of the display.
2) Wait for about 5 seconds and press MENU, POWER switch with 1 second interval.
3) The SVC OSD menu contains additional menus that the User OSD menu as described below.
a) Auto Color : W/B balance and Automatically sets the gain and offset value.
b) NVRAM INIT : EEPROM initialize.(24C08)
c) CLEAR ETI : To initialize using time.
d) AGING : Select Aging mode(on/off).
e) R/G/B-9300K : Allows you to set the R/G/B-9300K value manually.
f) R/G/B-6500K : Allows you to set the R/G/B-6500K value manually.
g) R/G/B-Offset : Allows you to set the R/G/B-Offset value manually.(Analog Only)
h) R/G/B-Gain : Allows you to set the R/G/B-Gain value manually.(Analog Only)
i) MODULE : To select applied module.
IBM 9 6
Video Signal 5 1
Compatible PC 15 11
Generator 10 6
5 1
C
PARALLEL PORT
d
13
se
1
tu
2C
25
No
14
23
RS
OFF ON
5V
L
Control Line
F
E
LL
C
RA
PA
VG ON
WE
S 5V
(110V/220V)
PO
E 74LS06
A
T
MO Power LED
CS
NI OFF 4.7K
YN
TO
V-S
R
74LS06
E ST Switch
B
B
F V-Sync On/Off Switch
(Switch must be ON.)
- 13 -
TROUBLESHOOTING GUIDE
1. NO POWER
NO POWER
(POWER INDICATOR OFF)
YES
CHECK
U501 PIN 3 VOLTAGE NO CHECK U501
(3.3V) ? (OPEN CHECK)
YES
IS U502
PIN2 (1.8V) NO
CHECK U502
VOLTAGE ?
YES
YES
Waveforms
1 U101-#127
- 14 -
2. NO RASTER (OSD IS NOT DISPLAYED) – LIPS
NO RASTER
(OSD IS NOT DISPLAYED)
YES
1. CONFIRM BRIGHTNESS
J403 PIN10 NO OSD CONTRL STATE.
5V? 2. CHECK MICOM DIM-ADJ
PORT
YES
CHECK
PULSE AS
CONTACTING SCOPE
PROBE TO CAUTION LABEL.
NO
(CONTACT PROBE TO LIPS
CAUTION LABEL.
CAN YOU SEE PULSE
AT YOUR
SCOPE?
YES
- 15 -
3. NO RASTER (OSD IS NOT DISPLAYED) – MSTAR
NO RASTER
(OSD IS NOT DISPLAYED)
U101 NO
PIN 71, 87 CHECK U501
3.3V?
YES
YES
U101
PIN27 IS 48KHz H-SYNC? CHECK CONNECTION
NO
2 PIN28 IS 60Hz V-SYNC? LINE FROM D-SUB TO
IS PULSE APPEARED U101
AT SIGNAL PINS?
AT MODE 12?
YES
TROUBLE IN CABLE
OR LCD MODULE
Waveforms
1 U101-#127, 128 2 U101-#32 H-SYNC 2 U101-#33 V-SYNC
- 16 -
4. TROUBLE IN DPM
TROUBLE IN DPM
NO CHECK PC
CHECK
3 PC IS NOT GOING
R442, R443
INTO DPM OFF MODE
YES
CHECK
U101 PIN 32, 33 NO
CHECK H/V SYNC LINE
SYNC PULSE ?
YES
TROUBLE IN U101
Waveforms
3 R442 H-Sync 3 R443 V-Sync
- 17 -
WIRING DIAGRAM
30P
6631T11012W
or 6631T11020W
6631T20023A 11P
6P
6631T12006L
- 18 -
010
020 160
030
100 130 140
120
090 110
- 19 -
150
EXPLODED VIEW
040 130
080
070 050
060
EXPLODED VIEW PARTS LIST
* Note: Safety mark
ACQ30348804 Cover Assembly, L1932P BRAND 160A 19" SILVER, ABS, R chassis, TCO03+4MS+ EPA
020 6304FLP339A LCD,Module-TFT, LM170E01-TLB5 DRIVER 17.0INCH 1280X1024 300CD COLOR 72% 4/3 450 . LG PHILIPS LCD
or 6304FLP278D LCD,Module-TFT, LM170E01-TLBJ LM170E01-TLBJ LG PHILPS TFT COLOR ZBD,300NITS,8MS,700/1,P5,645CH,MAGNA S/IC,ROHS LG PHILIPS LCD
or 6304FLP278C LCD,Module-TFT, LM170E01-TLBF DRIVER 17INCH 1280X1024 300CD COLOR 72% 4/3 700:1 - LG PHILIPS LCD
or 6304FLP278B LCD,Module-TFT, LM170E01-TLBE DRIVER 17INCH 1280X1024 300CD COLOR 72% 4/3 700:1 - LG PHILIPS LCD
or 6304FLP278A LCD,Module-TFT, LM170E01-TLB1 DRIVER 17.0INCH 1280X1024 300CD COLOR 72% - - - LG PHILIPS LCD
or EAJ32168501 LCD,Module-TFT, LM170E01-TLBM DRIVER 17.0INCH 1280X1024 300CD COLOR 72% 4/3 700:1 8MS, LVDS, NEC D-IC LG PHILIPS LCD .
or EAJ32168701 LCD,Module-TFT, LM170E01-TLBN DRIVER 17.0INCH 1280X1024 300CD COLOR 72% 4/3 700 VS 1 8MS, LVDS, NEC D-IC, P6 FACTORY LG PHILIPS LCD .
6304FLP310A LCD,Module-TFT, LM190E03-TLB5 DRIVER 19.0INCH 1280X1024 300CD COLOR - - - - LG PHILIPS LCD
or 6304FLP355A LCD,Module-TFT, LM190E03-TLBC DRIVER 19INCH 1280X1024 300CD COLOR 72% 4/3 700:1 - LG PHILIPS LCD
or 6304FLP337A LCD,Module-TFT, LM190E03-TLBB DRIVER 19.0INCH 1280X1024 300CD COLOR - - - - LG PHILIPS LCD
or 6304FLP336A LCD,Module-TFT, LM190E03-TLBA DRIVER 19.0INCH 1280X1024 300CD COLOR - - - - LG PHILIPS LCD
or 6304FLP313A LCD,Module-TFT, LM190E03-TLB8 DRIVER 19.0INCH 1280X1024 300CD COLOR - - - - LG PHILIPS LCD
or 6304FLP311A LCD,Module-TFT, LM190E03-TLB6 DRIVER 19.0INCH 1280X1024 300CD COLOR 72% - - - LG PHILIPS LCD
060 49509K0016A Plate, PRESS SPTE T0.3 SHIELD L1732 CHASSIS BRACKET
100 6871TPT312J PCB Assembly,Power, POWER T.T 4-LAMP(17/19) SOCKET TYPE+NO REGULATOR BRAND (TCO-03) -
160 6410TPW003A Power Cord, LP-33 & GFC18N<B90A+LS-60_1.87M_BLK LP-33 LS-60 1.87M - 250V 16A H05VV-F 3X0.75MM2 BLACK PCT N
- 20 -
REPLACEMENT PARTS LIST
CAUTION: BEFORE REPLACING ANY OF THESE COMPONENTS,
READ CAREFULLY THE SAFETY PRECAUTIONS IN THIS MANUAL.
* NOTE : S SAFETY Mark
AL ALTERNATIVE PARTS
- 21 -
DATE: 2006. 10. 30. DATE: 2006. 10. 30.
*S *AL LOC. NO. PART NO. DESCRIPTION / SPECIFICATION *S *AL LOC. NO. PART NO. DESCRIPTION / SPECIFICATION
U402 0IMMR00014A M24C02-RMN6TP 2KBIT 256X8BIT R430 0RJ0102D677 MCR03EZPJ100 10OHM 5% 1/10W
U403 0IMMR00014A M24C02-RMN6TP 2KBIT 256X8BIT R431 0RJ0102D677 MCR03EZPJ100 10OHM 5% 1/10W
U501 0IPMGKE011A KIA78D33F 4TO10V 3.3V 1.3W D R432 0RJ0102D677 MCR03EZPJ100 10OHM 5% 1/10W
U502 0IPMGSG019A LD1117S18TR 3.3TO8V 1.8V 12W R433 0RJ1001D677 MCR03EZPJ102 1KOHM 5% 1/10W
R434 0RJ4701D677 MCR03EZPJ472 4.7KOHM 5% 1/10
FILTERs R435 0RJ4701D677 MCR03EZPJ472 4.7KOHM 5% 1/10
R436 0RJ0332D677 MCR03EZPJ330 33OHM 5% 1/10W
L502 0LCML00003B MLB-201209-0120P-N2 120OHM 2 R437 0RJ0332D677 MCR03EZPJ330 33OHM 5% 1/10W
L503 0LCML00003B MLB-201209-0120P-N2 120OHM 2 R438 0RJ4701D677 MCR03EZPJ472 4.7KOHM 5% 1/10
L504 0LCML00003B MLB-201209-0120P-N2 120OHM 2 R439 0RJ4701D677 MCR03EZPJ472 4.7KOHM 5% 1/10
R440 0RJ0332D677 MCR03EZPJ330 33OHM 5% 1/10W
TRANSISTOR R441 0RJ1000D677 MCR03EZPJ101 100OHM 5% 1/10W
R442 0RJ0682D677 MCR03EZPJ680 68OHM 5% 1/10W
Q101 0TR390409AE KST3904 NPN 6V 60V 40V 200MA R443 0RJ0682D677 MCR03EZPJ680 68OHM 5% 1/10W
Q401 0TR390409AE KST3904 NPN 6V 60V 40V 200MA R444 0RJ0332D677 MCR03EZPJ330 33OHM 5% 1/10W
Q402 0TR390409AE KST3904 NPN 6V 60V 40V 200MA R445 0RJ0752D677 MCR03EZPJ750 75OHM 5% 1/10W
R446 0RJ0752D677 MCR03EZPJ750 75OHM 5% 1/10W
RESISTORs R447 0RJ0000D677 MCR03EZPJ000 0OHM 5% 1/10W 1
R448 0RJ0752D677 MCR03EZPJ750 75OHM 5% 1/10W
R101 0RJ0562D677 MCR03EZPJ560 56OHM 5% 1/10W R449 0RJ4701D677 MCR03EZPJ472 4.7KOHM 5% 1/10
R102 0RJ4700D677 MCR03EZPJ471 470OHM 5% 1/10W R450 0RJ4701D677 MCR03EZPJ472 4.7KOHM 5% 1/10
R103 0RJ1000D677 MCR03EZPJ101 100OHM 5% 1/10W R451 0RJ0000D677 MCR03EZPJ000 0OHM 5% 1/10W 1
R104 0RJ0562D677 MCR03EZPJ560 56OHM 5% 1/10W R501 0RJ2702D677 MCR03EZPJ273 27KOHM 5% 1/10W
R105 0RJ1000D677 MCR03EZPJ101 100OHM 5% 1/10W R502 0RJ2202D677 MCR03EZPJ223 22KOHM 5% 1/10W
R106 0RJ0562D677 MCR03EZPJ560 56OHM 5% 1/10W R503 0RJ5600D677 MCR03EZPJ561 560OHM 5% 1/10W
R107 0RJ1000D677 MCR03EZPJ101 100OHM 5% 1/10W
R110 0RJ3900D677 MCR03EZPJ391 390OHM 5% 1/10W OTHERs
R113 0RJ1002D677 MCR03EZPJ103 10KOHM 5% 1/10W
R114 0RJ4701D677 MCR03EZPJ472 4.7KOHM 5% 1/10 SW101 6600D000010 NVS4602 NAMAE 12VDC 1MA TILT
R115 0RJ1002D677 MCR03EZPJ103 10KOHM 5% 1/10W SW102 6600D000010 NVS4602 NAMAE 12VDC 1MA TILT
R116 0RJ1502D677 MCR03EZPJ153 15KOHM 5% 1/10W U503 0TFVI80067A SI3865BDV(E3) N-CHANNEL MOSF
R117 0RJ4701D677 MCR03EZPJ472 4.7KOHM 5% 1/10 X101 6202VDT002B SX-1 14.31818MHZ 30PPM 14.31
R118 0RJ0332D677 MCR03EZPJ330 33OHM 5% 1/10W
R119 0RJ4701D677 MCR03EZPJ472 4.7KOHM 5% 1/10 CONTROL BOARD
R120 0RJ0332D677 MCR03EZPJ330 33OHM 5% 1/10W
R121 0RJ0000D677 MCR03EZPJ000 0OHM 5% 1/10W 1 SW1 140-058E THVV502GBC 1C1P 12VDC 0.05A
R122 0RJ0000D677 MCR03EZPJ000 0OHM 5% 1/10W 1 SW2 140-058E THVV502GBC 1C1P 12VDC 0.05A
R124 0RJ1002D677 MCR03EZPJ103 10KOHM 5% 1/10W SW3 140-058E THVV502GBC 1C1P 12VDC 0.05A
R125 0RJ1002D677 MCR03EZPJ103 10KOHM 5% 1/10W SW4 140-058E THVV502GBC 1C1P 12VDC 0.05A
R128 0RJ0000D677 MCR03EZPJ000 0OHM 5% 1/10W 1 SW5 140-058E THVV502GBC 1C1P 12VDC 0.05A
R130 0RJ4701D677 MCR03EZPJ472 4.7KOHM 5% 1/10 C1 0CK104CK56A 0603B104K500CT 100nF 10% 50V
R131 0RJ1000D677 MCR03EZPJ101 100OHM 5% 1/10W C2 0CK104CK56A 0603B104K500CT 100nF 10% 50V
R402 0RJ2001D677 MCR03EZPJ202 2KOHM 5% 1/10W LED1 0DLBE0248AA BL-HB5KC39C-TRB BLUE-YELLOW
R403 0RJ2001D677 MCR03EZPJ202 2KOHM 5% 1/10W LED2 0DLBE0248AA BL-HB5KC39C-TRB BLUE-YELLOW
R404 0RJ4701D677 MCR03EZPJ472 4.7KOHM 5% 1/10 Q1 0TR390409AE KST3904 NPN 6V 60V 40V 200MA
R405 0RJ4701D677 MCR03EZPJ472 4.7KOHM 5% 1/10 Q2 0TR390409AE KST3904 NPN 6V 60V 40V 200MA
R406 0RJ4701D677 MCR03EZPJ472 4.7KOHM 5% 1/10 R1 0RJ7501D677 MCR03EZPJ752 7.5KOHM 5% 1/10
R407 0RJ4701D677 MCR03EZPJ472 4.7KOHM 5% 1/10 R10 0RJ1000D677 MCR03EZPJ101 100OHM 5% 1/10W
R408 0RJ4701D677 MCR03EZPJ472 4.7KOHM 5% 1/10 R11 0RJ1000D677 MCR03EZPJ101 100OHM 5% 1/10W
R409 0RJ4701D677 MCR03EZPJ472 4.7KOHM 5% 1/10 R2 0RJ7501D677 MCR03EZPJ752 7.5KOHM 5% 1/10
R413 0RJ4701D677 MCR03EZPJ472 4.7KOHM 5% 1/10 R3 0RJ1201D677 MCR03EZPJ122 1.2KOHM 5% 1/10
R414 0RJ4701D677 MCR03EZPJ472 4.7KOHM 5% 1/10 R4 0RJ1201D677 MCR03EZPJ122 1.2KOHM 5% 1/10
R415 0RJ4701D677 MCR03EZPJ472 4.7KOHM 5% 1/10 R5 0RJ1801D677 MCR03EZPJ182 1.8KOHM 5% 1/10
R416 0RJ4701D677 MCR03EZPJ472 4.7KOHM 5% 1/10 R6 0RJ8200D677 MCR03EZPJ821 820OHM 5% 1/10W
R417 0RJ1000D677 MCR03EZPJ101 100OHM 5% 1/10W R7 0RJ8200D677 MCR03EZPJ821 820OHM 5% 1/10W
R418 0RJ1000D677 MCR03EZPJ101 100OHM 5% 1/10W R8 0RJ8200D677 MCR03EZPJ821 820OHM 5% 1/10W
R424 0RJ1000D677 MCR03EZPJ101 100OHM 5% 1/10W R9 0RJ8200D677 MCR03EZPJ821 820OHM 5% 1/10W
R425 0RJ0102D677 MCR03EZPJ100 10OHM 5% 1/10W
R426 0RJ0102D677 MCR03EZPJ100 10OHM 5% 1/10W
R427 0RJ0102D677 MCR03EZPJ100 10OHM 5% 1/10W
R428 0RJ0102D677 MCR03EZPJ100 10OHM 5% 1/10W
R429 0RJ0102D677 MCR03EZPJ100 10OHM 5% 1/10W
- 22 -
SCHEMATIC DIAGRAM
1. SCALER
- 23 -
2. POWER & WAFER
- 24 -
3. DC-DC BLOCK
- 25 -
Oct. 2006
P/NO : MFL36713603 Printed in Korea