Professional Documents
Culture Documents
www.philips.com/welcome
EN USER MANUAL
Model
www.philips.com/support Serial
ENglish
Congratulations on your purchase and • To avoid risk of fire or electric shock, do
welcome to Philips! not place the TV, remote control or remote
control batteries near naked flame sources
Read this user manual before you start to use (e.g. lighted candles) and other heat sources
this product. including direct sunlight.
Pay close attention to this section and follow • Do not install the TV in a confined space
the safety and screen care instructions. The such as a bookcase. Leave a space of at
product warranty does not apply if damage is least 10cm (four inches) around the TV
caused by failing to follow these instructions. for ventilation. Be sure air flow is not
To fully benefit from the support that Philips obstructed.
offers, register your product at • If placing the TV on a flat, solid surface be
www.philips.com/welcome. sure to use only the supplied stand. Do not
The model and serial number of your TV can move the TV if the stand is not properly
be found on the back and side of the TV as well screwed to the TV.
as on the packaging. • Wall mounting of the TV should only be
performed by qualified personnel. The TV
must only be mounted on an appropriate
wall bracket and on a wall that can safely
hold the weight of the TV. Improper wall
mounting can result in severe injury or
damage. Do not attempt to wall mount the
TV yourself.
• If the TV is mounted on a swivel base or
swivel arm, ensure no strain is placed on
1.1 Safety the power cord when the TV is swivelled.
Strain on the power cord can loosen
• Two people are required to lift and carry a
connections and cause arcing or fire.
TV that weighs more than 25 kilos (55lb).
Improper handling of the TV can result in • Disconnect the TV from the mains and
serious injury. antenna before lightning storms. During
lightning storms do not touch any part of
• If transporting the TV in low temperatures
the TV, mains cord or antenna cable.
(less than 5°C), open the box and wait until
the TV matches the ambient temperature • Be sure that you have full access to the
of the room before unpacking. mains cord for easy disconnection of the
TV from the mains.
• To avoid short circuit, do not expose the
TV, remote control or remote control • When disconnecting the TV from the mains,
batteries to rain or water. be sure to:
• Do not place vessels of water or other 1. Turn off the TV, then the mains power (if
liquids on top of or near the TV. Spilling available).
liquids on the TV can cause electric shock.
2. Unplug the mains cord from the mains
If liquids are spilt on the TV, do not operate
socket outlet.
the TV. Immediately disconnect the TV from
EN-3
3. Unplug the mains cord from the power of time. Examples include screen menus,
connector at the back of the TV. teletext pages, black bars or stock market
Always pull the mains cord by the plug. Do tickers. If you must use stationary images,
not pull the mains cord. reduce the screen contrast and brightness
to avoid screen damage.
• Permanent hearing loss can occur if you use Disposing your used product
earphones or headphones at high volumes.
Your product is manufactured with high-quality
Though high volume may sound normal
materials and components that can be recycled
over time, it can damage your hearing. To
and reused. When you see the crossed-out
protect your hearing, limit the amount of
wheel bin symbol attached to a product, it
time you use earphones or headphones at
means the product is covered by the European
high volume.
Directive 2002/96/EC:
EN-4
2 Your TV Side connectors
ENglish
This section gives you an overview of
commonly-used TV controls and functions.
2.1 TV overview
Side controls and indicators
VOLUME
4
Use the TV side connectors to connect to
mobile devices such as a camera or high-
3 definition game console. You can also connect
a pair of headphones or a USB memory device.
MENU
2
Back connectors
PROGRAM
1
POWER
1. POWER
2. PROGRAM +/-
3. MENU
4. VOLUME +/-
Use the TV back connectors to connect to the
5. Power indicator/Remote control sensor
antenna and permanent devices such as a high-
definition disc player, DVD player or VCR.
DDNote
For more information about connections,
see Section 7 Connect devices.
EN-5
Remote control 1. STANDBY
2. SOURCE
3. TELETEXT
1 4. COLOUR KEYS
From left: Red, green, yellow, blue
SOURCE 2 5. NAVIGATION KEYS
3 Up Î, Down ï, Left Í, Right Æ, OK
TELETEXT SUBTITLE
DEMO 6. MENU
4 7. PROGRAM +/-
GUIDE
8. VOLUME +/-
INFO
EXIT OPTION
MENU 6
BROWSE
P 7
8
1 2 3
4 5 6
7 8 9
MHEG
CANCEL 0
EN-6
3 Get started 3.2 Wall mount the TV
ENglish
BBWARNING
This section helps you position and install the
Wall mounting of the TV should only
TV and supplements the information provided
be performed by qualified installers.
in the Quick Start Guide.
Koninklijke Philips Electronics N.V. bears no
DDNote responsibility for improper mounting that
Refer to the Quick Start Guide for stand results in accident or injury.
mounting instructions.
Step 1 Purchase a VESA-compatible wall
3.1 Position the TV bracket
Depending on the size of your TV screen,
In addition to reading and understanding the purchase one of the following wall brackets:
safety instructions in Section 1.1, consider the
following before positioning your TV: TV VESA- Special
screen compatible instructions
• The ideal viewing distance for watching TV size wall bracket
is three times its screen size. (inches/ type
• Position the TV where light does not fall on cm) (millimeters)
the screen. 32”/81cm Adjustable The VESA-
300 x 300 compatible
• Connect your devices before you position bracket must
your TV. be adjusted
• Your TV is equipped with a Kensington to 200 x
Security Slot at the back of the TV. 300 before
securing to
the TV
37”/94cm Fixed 300 x 300 None
EN-7
Step 2 Remove the TV stand
DDNote
These instructions are only applicable to
TV models with mounted stands. If your TV
stand is not mounted, skip to Step 3 Secure
the VESA-compatible wall bracket to the TV.
TV stands may differ in shape on some TV
models.
DDNOTE
When securing the VESA-compatible wall
bracket to your TV, use M6 bolts for 32 inch
models or M8 bolts for larger models (bolts
not supplied).
EN-8
3.3 Connect the antenna cable
ENglish
1. Locate the TV ANTENNA connector at
the back of the TV.
UK - EIRE
2. Connect one end of an antenna cable
(not supplied) to the TV ANTENNA
1. Locate the AC IN mains connector at the
connector. Use an adaptor if the antenna
back or on the bottom of the TV.
cable does not fit.
2. Connect the mains cord to the AC IN
3. Connect the other end of the antenna
mains connector.
cable to your antenna outlet, ensuring that
the cable is tightly secured at both ends. 3. Connect the mains cord to the mains,
ensuring that the cord is tightly secured at
both ends.
3.4 Connect the mains cord
BBWARNING
Verify that your mains voltage corresponds
with the voltage printed at the back of the
TV. Do not insert the mains cord if the
voltage is different.
DDNote
The location of the mains connector varies
according to TV model.
EN-9
3.5 Insert the remote control 3.7 First time setup
batteries The first time the TV is switched on, a
language selection menu appears.
Menu language
Please select your English
language... Español
Français
Hrvatski
Italiano
1. Slide the battery cover off the back of the using cursor up and Magyar
remote control. down ...
DDNote
Certain TV models require you to press
and hold POWER for up to two seconds.
A beep sound indicates that your TV is
switched on.Your TV may take up to 15
seconds to start.
EN-10
4 Use your TV 4.1.3 Switch your TV to standby
ENglish
This section helps you perform basic TV
operations. Instructions on advanced TV opera-
tions are provided in Section 5 Use more of your
TV.
MENU
PROGRAM
• If the power indicator is in standby (red),
press . STANDBY on the remote
control.
POWER
1 DDNote
• Press POWER on the side of the TV. The If you cannot locate your remote control
power indicator (1) switches off. and you want to switch on the TV from
standby, press POWER on the side of
the TV. This switches off your TV. Press
POWER again to switch the TV back on.
EN-11
4.2 Watch TV 4.2.3 Adjust volume
DDNote
For instructions on how to install DVB-C
and DVB-T channels, see Section 6.1
Automatically install channels.
EN-12
4.4 Use teletext
ENglish
Most TV channels broadcast information via
teletext.
Tip
Press to return to the previously
viewed page.
3. Press TELETEXT again to switch off
teletext.
EN-13
5 Use more of your TV 5.1 Remote control overview
This section provides a detailed overview of
This section helps you perform advanced TV remote control features.
operations, including how to:
14
1 2 3 11
4 5 6
7 8 9
13 MHEG
CANCEL 0 12
EN-14
1. STANDBY 19. DEMO
Switches the TV on from standby or back Toggles the Demo menu on or off.
to standby.
ENglish
20. TELETEXT
2. SOURCE Toggles teletext on or off.
Selects connected devices.
21. DUAL SCREEN
3. PICTURE FORMAT Splits the current channel or source on the
Selects a picture format. left of the screen. Teletext appears on the
4. SUBTITLE right.
Activates or deactivates subtitles.
5. COLOUR KEYS
Selects tasks or teletext pages.
6. INFO
Displays programme information, if available.
7. OK
Accesses the All channels menu or
activates a setting.
8. NAVIGATION KEYS
Up Î, Down ï, Left Í and Right Æ keys
navigate the menu.
9. OPTION
Activates the Quick access menu.
10. PROGRAM (P) +/-
Switches to the next or previous channel.
11. NUMBER KEYS
Selects a channel, page or setting.
12. PREVIOUS CHANNEL
Returns to the previously-viewed channel.
13. MHEG CANCEL
Cancels digital text or interactive services
(UK only).
14. MUTE
Mutes or restores sound.
15. VOLUME +/-
Increases or decreases volume.
16. MENU
Toggles the menu on or off.
17. BACK
18. GUIDE
Toggles the Electronic Programme Guide
on or off. Only active with digital channels.
EN-15
5.2 Use TV menus 5.2.2 Use the main menu
On-screen menus help you install your TV, The following example describes how to use
adjust picture and sound settings and access the main menu.
other features. This section describes how to
navigate the menus.
Television TV menu
Channel list
1. Press MENU on the remote control to Programme guide
display the main menu. Multimedia
Television TV menu
Channel list 2. Press Æ to enter the TV menu.
Programme guide
TV menu TV settings
Multimedia
TV settings Settings assistant
Features Reset smart settings
2. Press MENU to exit. Installation Picture
Software update Sound
The main menu offers the following items:
• TV menu
3. Press Æ to enter the TV settings menu.
Select this menu for installation, picture,
sound settings and other feature settings. TV settings Settings assistant
EN-16
4. Press ï to select Picture. DDNote
More choices are available when digital
TV settings Picture
ENglish
channels are installed and broadcast.
Settings assistant Contrast
Reset smart settings Brightness
5.2.3 Use the Quick access menu
Picture Colour
Sound Hue The Quick access menu gives direct access to
Sharpness some often-needed menu items.
Tint
DDNote
5. Press Æ to enter the Picture settings. When digital channels are installed and
Picture Contrast
broadcasted, the relevant digital options are
displayed in the Quick access menu.
Contrast 90
Brightness 47
1. Press OPTION on the remote control.
Colour 52
Hue 0 2. Press Î or ï to select an option:
Sharpness 4 • Audio language (digital)
Tint See Section 5.3.5 Adjust sound settings.
• Subtitle language (digital)
See Section 5.9.3 Select a subtitle
language on digital TV channels.
6. Press ï to select Brightness. • Subtitle
Picture Brightness See Section 5.9 Use subtitles.
• Picture format
Contrast 98
See Section 5.3.4 Change picture format.
Brightness 47
• Equalizer
Colour 52
See Section 5.3.5 Adjust sound
Hue 0
settings.
Sharpness 4
• Clock
Tint
3. Press OK to display the selected option
menu.
7. Press Æ to enter the Brightness setting. 4. Press Î, ï, Í, Æ to adjust the settings in
the menu.
Brightness
5. Press OPTION to exit the menu.
EN-17
5.3.2 Adjust picture settings
Quick access
Audio language This section describes how to adjust picture
Subtitle language settings.
Subtitle
Picture format 1. Press MENU on the remote control
Equalizer and select TV menu > TV settings >
Clock Picture.
TV settings Picture
EN-18
follow the on-screen instructions to 5.3.3 Use smart settings
change the value of:
Apart from manually adjusting picture settings,
ENglish
- R-WP (Red White Point)
you can use smart settings to set your TV to a
- G-WP (Green White Point)
predefined picture and sound setting.
- B-WP (Blue White Point)
- R-BL (Red Black Level)
1. Press MENU on the remote control and
- G-BL (Green Black Level)
select TV menu > TV settings > Reset
• Dynamic contrast smart settings.
Enhances the contrast in the picture as the
2. Press Æ to enter the list.
image on the screen changes.
Set the level to Minimum, Medium, 3. Press Î or ï to select one of the following
Maximum or Off. Medium is settings:
recommended.
• Current
• Noise reduction Applies manually selected picture and
Filters and reduces the noise in the picture. sound settings.
Set the level to Minimum, Medium,
• Standard
Maximum or Off.
Applies natural picture and sound
• Colour enhancement settings suitable for most living room
Makes colours more vivid and improves the conditions.
resolution of details in bright colours.
• Vivid
Set the level to Minimum, Medium,
Applies brilliant picture and sound
Maximum or Off.
settings suitable for bright surroundings.
• Active Control
• Movie
Corrects all incoming signals to provide
Applies dynamic picture and sound
the best picture possible. Switches Active
settings suitable for a complete
control On or Off.
cinematic experience.
• Light sensor
4. Press the green key to store your selection.
Adjusts picture settings to match lighting
conditions in the room. Switches Light
sensor On or Off.
DDNote
Not available on all TV models.
• Picture format
See Section 5.3.4 Change picture format.
EN-19
5.3.4 Change picture format DDNote
Constant use of the 4:3 picture format can
Change the picture format to suit your content.
cause screen distortion. We recommend
you use Auto format.
1. Press PICTURE FORMAT on your
remote control. Alternatively, press MENU
and select TV menu > TV settings > • Movie expand 14:9 (Not for HD)
Picture > Picture format.
DDNote
2. Press Î or ï to select one of the following
Constant use of the 14:9 picture format
picture formats:
can cause screen distortion. We recommend
• Auto format (Not for PC) you use Auto format.
EN-20
5.3.5 Adjust sound settings TV menu > Installation > Preferences.
Press Æ to enter the list and select Volume
This section describes how to adjust sound
ENglish
bar on or Volume bar off.
settings.
1. Press MENU on the remote control and
• Balance
select TV menu > TV settings > Sound.
Sets the balance of the left and right
2. Press Æ to enter the list. speakers to best fit your listening position.
TV settings Sound • Audio language
Settings assistant Equalizer
Lists audio languages available for a digital
Reset smart settings Volume
channel (unavailable on analogue channels).
Picture Balance • Dual I/II
Sound Audio language If available, choose between two different
Dual I/II languages.
Mono/Stereo
Surround mode
• Mono/Stereo
Headphone volume
If stereo broadcasting is available, choose
Auto volume leveling
between mono or stereo.
Delta volume • Surround mode
Auto surround If surround sound is available, enable it for
more spatial sound.
3. Press Î or ï to select one of the following
settings: • Headphone volume
Changes the volume of your headphones.
• Equalizer
Changes the bass and treble of the sound.
Select each bar to change a setting. DDNote
Alternatively, press the colour keys to When headphones are connected, press the
select a pre-defined equalizer setting: MUTE button on the remote control to
mute audio from the TV speakers. Pressing
• Standard VOLUME +/- buttons un-mutes the TV
Equalizer set to neutral. speakers.
• Speech
Equalizer settings maximized for speech- • Automatic volume leveling
based audio. Reduces sudden volume changes, for
example, during commercials or when
• Multimedia switching from one channel to another.
Settings maximized for different audio Select On or Off.
types.
• Delta volume
• Music Levels out volume differences between
Settings maximized for music. channels or connected devices. You must
• Volume switch to the connected device before
Changes the volume. changing the Delta volume.
• Auto surround
EETip Automatically switches the TV to the best
To enable or disable the volume bar that surround sound mode available from a
appears when you change the volume, press broadcast. Select On or Off.
MENU on the remote control and select
EN-21
5.4 Change to Shop or Home 2. Press INFO.
mode
1. Press MENU on the remote control
and select TV menu > Installation >
Preferences > Location.
2. Press Æ to enter the Location menu.
3. Use Î or ï to select the TV mode: The T.O.P. overview appears.
• Shop 3. Use Í, Æ or Î, ï to select a subject.
Sets smart settings to Vivid, ideal for
a shop environment. The flexibility to 4. Press OK to view the page.
change settings is limited.
• Home 5.5.3 Use dual screen teletext
Gives home users the full flexibility to
change all TV settings. Enabling dual screen teletext displays your
channel or source on the left of the screen.
4. Press OK to confirm. Teletext is displayed on the right.
5. Press MENU to exit.
1. Press DUAL SCREEN on your
remote control to enable dual screen
5.5 Use advanced teletext teletext.
features 2. Press again to display normal teletext .
Your TV has a 1,200 page memory that stores 3. Press TELETEXT to switch off teletext.
broadcasted teletext pages and subpages. The
teletext memory reduces page loading time.
5.5.4 Search teletext
1. Press TELETEXT on the remote control. 2. Press OK to highlight the first word or
number.
2. Select a teletext page.
3. Press Î, ï or Í, Æ to jump to the next
3. Press Í or Æ to select a subpage. word or number on the page.
4. Press OK to search a page which holds the
5.5.2 Select T.O.P. teletext broadcasts highlighted word or number.
Table Of Pages (T.O.P.) teletext broadcasts 5. Press Î until no word or number is
allow you to jump from one subject to another highlighted to exit Search.
without using page numbers. T.O.P. teletext is
not broadcast on all TV channels.
EN-22
5.5.5 Enlarge teletext pages • Cycle subpages
If subpages are available for the selected
For more comfortable reading, you can enlarge
ENglish
page, you can cycle subpages automatically.
the teletext page.
• Language
1. Press TELETEXT on the remote control Some languages use a different set of
and select a teletext page. characters. If using a different language,
switch to the appropriate language group to
2. Press OPTION on the remote control to
display the text correctly.
enlarge the top part of the page.
4. Press OK to change an option:
5. Press MENU to exit Teletext menu.
6. Press TELETEXT to switch off teletext.
1. Press TELETEXT on the remote control. 5. Press MHEG Cancel to cancel digital text
or interactive services.
2. Press MENU. The Teletext menu
appears. CCCaution
Teletext menu Digital text services are blocked when
Reveal Off subtitles are broadcasted and Subtitle On
Cycle subpages Off
is set in the Features menu as described in
Language Gr. II
Section 5.9 Subtitles.
EN-23
1. Press MENU on the remote control 5.6.2 Setup a favorite list
and select TV menu > Installation >
Preferences > Teletext 2.5. 1. Press OK on the remote control. The last
selected list appears.
2. Press Æ to enter the list.
2. Press the red key to show all favourite lists.
3. Select On or Off.
3. Press Î or ï to select a list.
4. Press OK to change the option.
4. Press OK.
5. Press the green key to enter Edit mode.
5.6 Create favorite lists
The selected list displays a full channel list.
Use the All channels list or setup a favourite 6. Press Î or ï to highlight a channel.
list of your own with preferred TV channels
and radio stations. Each member of your family 7. Press OK to mark (or unmark) the
can create his or her own favourite list. highlighted channel. The channel is added to
(or removed from) the selected list.
5.6.1 Select a favorite list 8. Press the green key again to exit Edit
mode. The modified channel list appears
1. Press OK on the remote control. again.
Alternatively, press MENU and select
Channel list.
If this is new installation, the All channels 5.6.3 Select a channel from a favorite
list is displayed. list
All channels
1. Press OK on the remote control. The last
....
selected channel list appears.
EXT 3
HDMI ... 2. Use Î or ï to highlight a channel.
A 1 Analogue channel 1
3. Press OK. The TV tunes to that channel.
2 Digital channel 1
3 Digital channel 2
4 Radio channel 1 EETip
....
Select list
EN-24
5.7 Use the Electronic
26 BBC1 Tue., 12 Sep 09:17
Programme Guide
ENglish
Title : Commonwealth Games
EN-25
1. Press GUIDE on the remote control. DDNote
You can always switch off your TV earlier or
2. Press MENU on the remote control. reset Sleeptimer during the countdown.
The Programme guide menu appears.
Programme guide What's on 5.8.2 Automatically switch the TV on
What's on 12:30 South Today (On timer)
Search by genre 11:50 Working Lunch
On timer switches the TV to a specified
Scheduled remind... 11:55 Melrose Place
channel at a specified time, from standby.
Preferred EPG ch... 13:00 In aller Freund
Acquire EPG data
1. Press MENU on the remote control
and select TV menu > Features > On
3. Press Î or ï to select a menu option. timer.
DDNote
Only channels marked as preferred EPG EETip
To switch off On timer, select Off in the
channels appear in the Programme guide
On timer menu.
menu.
Sleeptimer switches the TV to standby after a 1. Press MENU on the remote control and
defined period of time. select TV menu > Features > Set code
or Change code.
1. Press MENU on the remote control
2. Press Æ to enter the code setup.
and select TV menu > Features >
Sleeptimer. 3. Enter your code with the number keys.
The Features menu reappears with a
2. Press Æ to enter the Sleeptimer bar.
message confirming that your code is
3. Press Î or ï to set the sleep time. This created or changed.
can be up to 180 minutes in steps of
five minutes. If set to zero minutes, the EETip
Sleeptimer is switched off. If you forget your code, enter ‘8888’ to
4. Press OK to activate the Sleeptimer. override any existing codes.
EN-26
To enter the Child lock menu 3. Press Î or ï to select Channel lock.
4. Press Æ.
ENglish
1. Press MENU on the remote control and
select TV menu > Features > Child 5. Press Î or ï to select the channel or
lock and press Æ to enter your code. device you want to lock or unlock.
2. Enter your code with the number keys. 6. At each selection, press OK to lock or
unlock the channel or device.
To lock or unlock all channels and
connected devices To set parental ratings
1. In the Child Lock menu, select Lock or Some digital broadcasters rate their
Unlock. programmes according to age. You can set your
TV to display only programmes with age ratings
2. Press OK. higher than your child’s.
To lock a programme or all channels 1. In the Child lock menu, select Custom
from a certain time lock.
2. Press Æ to enter.
1. In the Child lock menu, select Custom
lock. 3. Press Î or ï to select Parental rating.
Child lock Custom lock 4. Press Æ.
Lock Lock after 5. Press Î or ï to select an age rating.
Custom lock Channel lock
Unlock Parental rating
6. Press Menu to exit the Child lock menu.
6. Select Time.
5.9.1 Enable subtitles on analogue TV
7. Press Æ. channels
8. Enter the time with Î or ï and Æ.
1. Select an analogue TV channel.
9. Press OK.
2. Press TELETEXT on the remote control.
To lock one or more channels and 3. Enter the three digit page number of the
connected devices subtitle page.
4. Press TELETEXT to switch off teletext.
1. In the Child lock menu, select Custom
lock. 5. Press MENU on the remote control and
select TV menu > Features > Subtitle.
2. Press Æ to enter.
6. Press Æ to enter the list.
EN-27
5.10 View photos and listen to
TV menu Features
music
TV settings Subtitle
Features Subtitle language Connect an external USB storage device and
Installation Sleeptimer view pictures (JPEG format only) or listen to
Software update Child lock music (MP3 or Linear PCM formats only).
Set/Change code
On timer
DDNote
Common interface
Philips will not be held responsible if your
Demo
USB storage device is not supported nor
shall Philips accept any liability for damage
7. Press Î or ï to select On to display or loss of stored data.
subtitles always or On during mute to
display subtitles only when the sound is 5.10.1 Connect a USB storage device
muted with the key on the remote
control. While your TV is on, connect your USB storage
device to the USB port on the side of your TV.
8. Press OK to return to the Features menu. The main menu appears automatically and the
name of the USB device is highlighted next to
DDNote Multimedia.
You must repeat this procedure to enable
subtitles on each analogue channel. Television TV menu
Channel list
Programme guide
5.9.2 Enable subtitles on digital TV
Multimedia
channels
Repeat steps 5 to 8 in Section 5.9.1 Enable
subtitles on analogue TV channels. DDNote
See Section 7.1 Connection overview for a
5.9.3 Select a subtitle language on description of the side connectors, including
digital TV channels the USB port.
EN-28
5.10.3 View your photos Slide show settings
ENglish
1. After connecting your USB storage • No details / More details
device to the TV, press Æ to enter the Displays the picture name, date, size and
Multimedia menu. Picture is highlighted. next picture in the slide show.
USB Picture • Transitions
Picture Afrika_2001 Displays the list of available transition styles
Music Paris_2006 of the pictures. Press Î or ï to select and
My_car.jpg press OK to activate.
Jean.jpg • Slide time
Mary.jpg Sets the time lag for picture transitions:
Short, Medium or Long.
2. Press Æ to enter the Picture folder.
• Rotate
3. Press Î or ï to select a picture or a
Rotates a picture.
picture album on the USB device.
• Zoom
Picture Afrika_2001
Displays a list of available zoom
Afrika_2001 Kenya.jpg magnifications.
Paris_2005 Congo.jpg
• Start show/Stop show
My_car.jpg Victoria.jpg
Starts or stops a slide show.
Jean.jpg Dakar.jpg
Mary.jpg Cairo.jpg
EN-29
Music folder. you update the TV software when updates are
available. Check www.philips.com/support for
3. Press Î or ï to select a song or a music
availability.
album.
4. Press OK to play the selected song or 5.12.1 Check your current software
album. version
If digital broadcasting is available, digital radio • Select Now (recommended) to update the
channels are installed automatically during software immediately.
installation. To reorder the digital radio
channels, see Section 6.5 Rearrange the channels. • Select Later to be reminded to update the
software later.
1. Press OK on the remote control. The All • Select Cancel to exit the update (not
channels menu is displayed. recommended). If you cancel the update,
2. Use the number keys to select a radio manually update the software by pressing
channel. MENU and selecting TV menu >
Software update > Local updates.
3. Press OK. Follow the on-screen instructions.
EN-30
5.12.4 Update software (analogue
broadcasts)
ENglish
DDNote
Before performing this procedure be sure
to:
• Set aside some time to complete the entire
update.
• Have available a USB storage device with at
least 64MB of storage space.
• Have access to a computer with a USB
port and internet access.
EN-31
6 Install channels 5. Press Í twice to return to the
Installation menu.
The first time you setup your TV, you will Installation Languages
be prompted to select an appropriate menu Languages Menu language
language and to perform automatic installation Time zone Primary audio
of all TV and digital radio channels (if available). Channel installation Secondary audio
Preferences Primary subtitles
This chapter provides instructions on how Connections Secondary subtitles
DDNote
Re-installing channels modifies the All
6. In addition to menu language, you can
MENU_installation_ENG.EPS
channels list.
configure the following language settings
via the Languages menu (digital channels
6.1 Automatically install only):
channels • Primary/Secondary audio
This section describes how to search and store Select primary and secondary audio
channels automatically. Instructions are for both languages for digital channels.
digital and analogue channels. • Primary/Secondary subtitles
Select primary and secondary subtitle
Step 1 Select your menu language languages for digital channels.
EN-32
4. Press OK to confirm. If you have access to DVB-T and DVB-C,
and want to view channels from both
5. Press Î or ï to select your country.
ENglish
networks, you must perform channel
6. Press Next. installation twice — once for DVB-T and
once for DVB-C. After installation, switch
between channels as described in Section 4.3
Step 3 Select Antenna or Cable Access DVB-C and DVB-T channel networks.
(DVB-C only)
EETip
DDNote When digital TV channels are found, the
This option appears only if your list of installed channels may display empty
country supports DVB-C (Digital Video channel numbers. If you want to rename,
Broadcasting-Cable). Skip to Step 4 Install reorder or uninstall stored channels, see
channels if DVB-C is not available in your Section 6.5 Rearrange channels.
country.
6.2 Manually install channels
1. Press Î or ï to select Antenna or
Cable. This section describes how to search and store
Selecting Antenna installs channels analogue TV channels manually.
available via DVB-T (Digital Video
Broadcasting-Terrestrial). Selecting Cable
Step 1 Select your system
installs channels available via DVB-C.
2. Press Next. DDNote
Skip to Step 2 Search and store new TV
channels if your system settings are correct.
Step 4 Install channels
1. Press MENU on the remote control
Your TV searches and stores all available digital
and select TV menu > Installation
and analogue TV channels as well as all available
> Channel installation > Analogue:
digital radio channels.
Manual installation.
CCCAUTION Channel install... Analogue: Manual...
If you select Cable in Step 3 Select Antenna
Automatic install... System
or Cable, a Settings menu is available. Leave
Installation update Search
settings unchanged unless your DVB-C Digital: Test recept... Fine tune
provider supplies values for Network Analogue: Manual... Store current ch...
frequency, Network ID or Symbol rate. Rearrange Store as new ch...
Note that setting Frequency scan to Full
can extend installation time significantly.
EN-33
Step 2 Search and store new TV channels 6.3 Rename channels
1. Press MENU on the remote control 1. Press MENU on the remote control
and select TV menu > Installation and select TV menu > Installation >
> Channel installation > Analogue: Channel installation > Rearrange.
Manual installation > Search.
2. Press Æ to enter the Rearrange list.
2. Press Æ to enter the Search menu.
3. Press Î or ï in the Rearrange list to
3. Press the red key and use the number keys select the channel you want to rename.
on the remote control to manually enter
the three digit frequency. Alternatively, press 4. Press the red key.
the green key to automatically search for
5. Press Í and Æ to select characters or Î
the next channel.
and ï to change the characters. Space,
4. Press Í when the new channel is found. numbers (0-9) and other special characters
are located between z and A.
5. Select Store as new channel to store the
new channel under a new channel number. 6. Press the green key or OK to finish.
6. Press Æ to enter.
EETip
7. Press OK. Done appears. Delete all characters by pressing the yellow
key. Delete only the highlighted character by
8. Press MENU to exit.
pressing the blue key.
EN-34
2. Press Æ to enter the Rearrange list. and select TV menu > Installation >
Channel installation > Digital: Test
3. Press Î or ï to select the channel you
ENglish
reception.
want to rearrange.
2. Press Æ to enter the Digital: Test
4. Press the yellow key to move the channel reception menu.
up the list. or press the blue key to move
the channel down the list. 3. Press OK.
5. Press MENU to exit. 4. Press the green key to automatically start
the test or manually enter the frequency of
the channel you want to test. If the signal
6.6 Manually update the channel quality and strength is poor, reposition the
list antenna or satellite dish and retest.
5. When complete, press the yellow key to
If your TV is in standby mode, an update is
store the frequency.
performed every morning. This update matches
channels stored in your channel list with those 6. Press the red key to return to the
available from your broadcaster. If a channel is Channel installation menu.
unavailable, it is automatically removed from
7. Press MENU to exit.
the channel list.
In addition to the automatic update, you can DDNote
manually update the channel list. If you have further problems with the
1. Press MENU on the remote control reception of your digital broadcast, contact
and select TV menu > Installation > a specialised installer.
Channel installation > Installation
update.
6.8 Start a demo
2. Press Æ to enter the Installation update
1. Press the red key on the remote control.
menu. Start now is highlighted.
Alternatively, press MENU on the remote
3. Press OK. control and select TV menu > Features
> Demo.
4. Press the green key to start the update.
This may take a few minutes. 2. Press Æ to enter the Demo menu.
5. When the update is complete, press 3. Select a demo and press OK.
the red key to return to the Channel
4. Press the red key to exit.
installation menu.
6. Press MENU to exit.
EN-35
6.9 Reset TV to factory settings
Resetting your TV to factory settings restores
default picture and sound settings. Channel
installation settings remain the same.
EN-36
7 Connect devices
ENglish
7.1 Connection overview
EN-37
Side connectors 7.2 Select connection quality
9. Headphones
Stereo mini-jack. This section describes how you can enhance
your audio visual experience by connecting
10. AUDIO L/R your devices with the best possible connectors.
Audio L/R input connectors for composite
and S-Video devices. After connecting your devices, be sure to
enable them as described in Section 7.4 Setup
11. VIDEO devices.
Video input cinch connector for composite
devices.
7.2.1 HDMI - Highest quality
12. S-VIDEO
S-Video input connector for S-Video
devices.
13. USB
USB connector for storage devices.
14. HDMI
Additional HDMI connector for mobile
high-definition devices.
15. COMMON INTERFACE HDMI produces the best audio visual quality
Slot for Conditional Access Modules. possible. Both audio and video signals are
combined in one HDMI cable, providing an
uncompressed, digital interface between your
TV and HDMI devices. You must use HDMI to
experience full high-definition video. You must
also use HDMI cables to enable Philips EasyLink
as described in Section 7.5 Use Philips EasyLink.
EETip
If your PC only has a DVI connector, use a
DVI-HDMI adaptor to connect your device
to a HDMI connector at the back of the TV.
You must connect a separate audio cable
from the device to the AUDIO IN mini-jack
connector.
DDNote
Philips HDMI supports HDCP (High-
bandwidth Digital Contents Protection).
HDCP is a form of Digital Rights
Management that protects high definition
content in DVD or Blu-ray Discs.
EN-38
7.2.2 Component (Y Pb Pr) - Higher 7.2.4 S-Video - Good quality
quality
An analogue connection, S-Video provides
ENglish
Component (Y Pb Pr) video provides better better picture quality than composite video.
picture quality than S-Video or composite When connecting your device with S-Video,
video connections. Though component video plug the S-Video cable to the S-Video
supports high-definition signals, picture quality connector on the side of the TV. You must
is lower than HDMI and is analogue. connect a separate Audio L/R cable from
the device to the red and white Audio L/R
When connecting a component video cable,
connectors on the side of the TV.
match the cable colours to the EXT 3
connectors on the back of the TV. Also, connect
a Audio L/R cable to the red and white Audio
L/R input connectors at EXT 3.
EN-39
7.3 Connect devices
This section describes how to connect
various devices with different connectors and
supplements examples provided in the Quick
Start Guide.
CCCaution
Disconnect the mains cord before
connecting devices.
DDNote
Different types of connectors may be used
to connect a device to your TV, depending
on availability and your needs.
DVD Player
EN-40
7.3.3 Satellite receiver
To receive analogue channels via antenna
ENglish
and digital channels via a satellite receiver,
connect an antenna cable and SCART cable as
illustrated:
Satellite receiver
HDMI
OUT OUT IN
EN-41
7.3.5 Combined DVD recorder and
digital receiver
To receive analogue channels via antenna and
record programs on a combined DVD recorder
and digital receiver, connect two antenna cables
and one SCART cable as illustrated:
OUT IN
OUT IN OUT IN
EN-42
7.3.7 DVD recorder and home theatre
system
ENglish
To receive analogue channels via antenna,
output sound to a home theatre system and
record programmes on a DVD recorder,
connect two antenna cables, one SCART cable
and two digital audio cables as illustrated:
DDNote
7.3.8 Game console or camcorder
If using a home theatre or other audio
system, the best synchronisation between The most practical connection for a mobile
images and sound is achieved by connecting game console or camcorder may be at the side
the audio signal from your playback device of the TV. You can, for example, connect the
to the TV first. Subsequently, channel the game console or camcorder to VIDEO/S-Video
audio signal to the home theatre system or and AUDIO L/R connnectors at the side of
audio device via the audio connectors on the TV. A HDMI connector is also available for
the back of the TV. high-definition devices.
EN-43
A permanent game console or camcorder can 7.4 Setup devices
be connected to a HDMI connector or EXT 3
(component) connectors at the back of the TV. When all devices are connected, you must
select the type of device attached to each
7.3.9 Personal Computer connector.
EN-44
Connections > Audio In L/R. 7.5.1 Enable or disable EasyLink
Connections AUDIO IN L/R
ENglish
1. Press MENU on the remote control
... None then select TV menu > Installation >
EXT 3 HDMI 1 Preferences > EasyLink.
HDMI 1 HDMI 2
HDMI 2 HDMI 3 2. Select On or Off.
HDMI 3
Side
7.5.2 Use one-touch play
AUDIO IN L/R
3. Press ï or Î to select the channel to The CAM may enable several digital services,
depending on the operator and services
decode.
you choose (for example, pay TV). Contact
4. Press Í and go back to select Status. your digital TV service operator for more
information about services and terms.
5. Press ï or Î to select the connector used
by the decoder.
7.6.1 Using the Conditional Access
6. Press MENU to exit. Module
BBWARNING
7.5 Use Philips EasyLink Switch off your TV before inserting a CAM.
Be sure to follow the instructions described
Your TV supports Philips EasyLink, which below. Wrong insertion of a CAM may
damage both the CAM and your TV.
enables one-touch play and one-touch standby
between EasyLink-compliant devices. Compliant 1. Following the directions printed on the
devices must be connected to your TV via CAM, gently insert the CAM into the
HDMI and assigned as described in Section 7.4.1 Common Interface on the side of the TV.
Assign devices to connectors.
EN-45
DDNote
Do not remove the CAM from the slot.
Removing the CAM will deactivate the
digital services.
EN-46
8 Technical • EXT 3: Component (Y Pb Pr), Audio L/R in
ENglish
Supported display resolutions DDNote
• Computer formats The number of HDMI connectors available
Resolution Refresh rate may vary according to your TV model.
640 x 480 60Hz
800 x 600 60Hz • SPDIF OUT: Digital audio out (coaxial-
1024 x 768 60Hz cinch-S/PDIF). Display synchronised.
1920 x 1080i 60Hz • AUDIO OUT L/R: Analogue audio out.
1920 x 1080p 60Hz
• TV ANTENNA
• Video formats
Resolution Refresh rate • AUDIO IN: Mini-jack audio in for PC DVI-
480i 60Hz HDMI connections.
480p 60Hz
576i 50Hz Connections (Side)
576p 50Hz • Headphone out (stereo mini-jack)
720p 50Hz, 60Hz • AUDIO L/R in
1080i 50Hz, 60Hz
1080p 24Hz, 25Hz, 30Hz • Video (CVBS) in
1080p 50Hz, 60Hz • S-Video
Connections (Rear)
• EXT 1 (SCART): Audio L/R, CVBS in/out,
RGB
• EXT 2 (SCART): Audio L/R, CVBS in/out,
RGB
EN-47
9 Troubleshooting • No action is required. The creaking sound
is normal expansion and contraction of the
TV as it cools and warms up. This does not
This section describes commonly-encountered impact performance.
issues and accompanying solutions.
EN-48
• Verify if the correct TV system is selected does not indicate malfunction.
for your region.See Section 6.2 Manually
ENglish
install channels. • Check that all cables are properly
connected.
• If reception on only one channel is poor,
try to fine tune this channel. See Section • Check that the volume is not set to 0.
6.2.1 Fine tune channels.
• Check that the sound is not muted.
You receive poor picture quality from
There is picture but sound quality is
connected devices:
poor:
• Check that the devices are connected
• Check Sound settings as described in
properly. Also, be sure to assign devices to
Section 5.3.5 Adjust sound settings, verifying
connectors as described in Section 7.4.1
that Stereo selected and Equalizer
Assign devices to connectors.
settings are correct. If needed, try resetting
• Verify that picture settings are correctly set. audio settings to standard.
See Section 5.3.2 Adjust picture settings.
There is picture but sound comes from
The TV did not save my settings: one speaker only:
• Verify that the TV is set to Home mode, • Verify that Balance correctly set as
which offers you complete flexibility to described in Section 5.3.5 Adjust sound
change settings. See Section 5.4 Change to settings.
Shop or Home mode.
The picture does not fit the screen, it is 9.5 HDMI connection issues
too big or too small:
• Try using a different picture format as You encounter problems with HDMI
described in Section 5.3.4 Change picture devices
format. • HDCP support can delay the time taken for
a TV to display content from a device.
• Assign your device to connectors as
described in Section 7.4.1 Assign devices to • If the TV does not recognise the device and
connectors. the screen displays no picture, try switching
from one device to another and back again
The picture position on screen is not to restart.
correct: • If you experience intermittent sound
• Picture signals from some devices do not disruptions, check the user manual of the
fit the screen correctly. Check the signal HDMI device to verify that output settings
output of the device. are correct. Alternatively, try connecting the
audio signal from the HDMI device to the
TV via AUDIO IN at the back of the TV.
9.4 Sound issues
• If a HDMI-to-DVI adaptor or HDMI to
There is picture but no sound from the DVI cable is used, check that an additional
TV: audio cable is connected to AUDIO IN. You
must also assign the audio connector as
DDNote described in Section 7.4.2 and 7.4.3.
If no audio signal is detected, the TV
automatically switches off audio output and
EN-49
9.6 USB connection issues
The TV does not display the USB device
content:
• Set your device to ‘Mass Storage Class’
compliant, as described in your device
documentation.
• Your USB device may not be compatible
with the TV.
• Not all audio and picture files are
supported. See Section 8 Technical
specifications for a list of supported file
types.
EN-50
10 Index Rename 34
Test digital reception 35
ENglish
Uninstall 34
A Update channel list 35
Active Control 19 Child lock
All channels list 24 Lock all channels/devices 27
Analogue Lock from a certain time 27
Channel installation 33 Lock one or more channel/device 27
Fine tune channels 34 Set/change code 26
Antenna Set parental rating 27
Connect 9 Clock 17
Assign Colour enhancement 19
Devices 44 Component cable 39
Audio language 21 Composite 39
Automatic Conditional Access Module (CAM)
Channel installation 32 Insert 45
Surround 21 Menu 46
Volume leveling 21 Connections
Back connectors 37
B Cable quality
Back connectors 5 Component 39
Balance Composite 39
Sound 21 HDMI 38
Brightness 18 SCART 39
S-Video 39
C Devices
Care Blu-ray Disc player 40
Environment 4 Conditional Access Module (CAM) 45
Screen 4 DVD player 40
Channels DVD recorder/Digital receiver 42
All channels list 24 DVD recorder/Home theatre system 43
Change 12 DVD recorder/Receiver 42
Decoder 45 Game console/camcorder 43
Favorite lists HD digital receiver 41
Select 24 PC 44
Setup 24 Satellite receiver 41
Use 24 USB 28
Installation Philips Easylink
Automatic 32 Enable/disable 45
Manual 33 Use 45
Rearrange 34 Setup devices
EN-51
Assign channel decoder 45 L
Assign to connectors 44 Language
Side connectors 38 Audio 21
Contrast 18 Menus 32
Country Subtitles 28
Selection 32 Light sensor 19
Custom tint 18
M
D Mains
Decoder 45 Connect 9
Delta volume 21 Manual channel installation 33
Demo 35 Menus
Devices Child lock 26
Watch 12 Language 32
Digital Main
Radio 30 Access 16
Services 45 Use 16
Teletext 23 Quick access
Dual I/II 21 Use 17
Dual screen teletext 22 Teletext menu 23
Dynamic contrast 19 Mono sound 21
Mute 15
E
Electronic Programme Guide N
Use 25 Noise reduction 19
Environmental care 4
Equalizer 21 O
On timer 26
F
Factory setting 36 P
Favorite lists 24 Parental rating 27
Fine tune channels 34 Philips EasyLink 45
Photos and music
H Connect USB device 28
HDCP 38 Listen to music 29
HDMI cable 38 View photos 29
Home mode 22 View slide show with music 30
Hue 18 Picture
Adjust settings
K Active Control 19
Kensington lock 7 Brightness 18
EN-52
Colour 18 Adjust settings 18
Colour enhancement 19 Change format 20
ENglish
Contrast 18 Use Settings assistant 18
Custom tint 18 Use smart settings 19
Dynamic contrast 19 Sound
Hue 18 Adjust settings 21
Light sensor 19 TV location
Noise reduction 19 Change location 22
Sharpness 18 Setup devices 44
Tint 18 Sharpness 18
Change format 20 Shop mode 22
Use Settings assistant 18 Side
Use smart settings Connectors 5
Current 19 Controls 5
Movie 19 Sleeptimer 26
Standard 19 Smart settings
Vivid 19 Current 19
Position TV 7 Movie 19
Power Standard 19
Connect 9 Vivid 19
Software update
Q Check availability 30
Quick access menu 17 Check version 30
Update (analogue) 31
R Update (digital) 30
Radio channels 30 Sound
Rearrange channels 34 Adjust settings
Recycling product 4 Audio language 21
Remote control Automatic volume leveling 21
Advanced use 14 Auto surround 21
Basic use 6 Balance 21
Batteries 10 Delta volume 21
Rename channels 34 Dual I/II 21
Reset to factory settings 36 Equalizer 21
Headphone volume 21
S Mono/Stereo 21
Safety information 3 Surround mode 21
SCART cable 39 Volume 21
Screen care 4 Stereo sound 21
Settings Subtitles
Picture Analogue TV 27
EN-53
Digital TV 28 Antenna 9
Language 28 Mains 9
Surround sound Connections
Auto 21 Back 37
Mode 21 Devices 40
S-Video 39 Quality 38
Switch TV Side 38
Off 11 Demo 35
On 10, 11 Electronic Programme Guide 25
On from standby 11 Get started 7
To standby 11 Main menus
System selection 33 Access 16
Use 16
T Overview 5
Technical specifications 47 Photos and music 28
Teletext Position 7
Advanced use Ideal distance 7
Cycle subpages 23 Quick access menu
Digital teletext 23 Use 17
Dual screen 22 Remote control
Enlarge 23 Advanced use 14
Language 23 Basic use 6
Reveal 23 Batteries 10
Search 22 Reset to factory setting 36
Select subpages 22 Side controls 5
Teletext 2.5 23 Software update 30
T.O.P broadcasts 22 Stand 8
Timers Subtitles 27
On timer 26 Switch
Sleeptimer 26 Off 11
Time zone 33 On 10, 11
Tint 18 On from standby 11
T.O.P. teletext 22 To standby 11
Troubleshooting 47 Teletext
TV Advanced use 22
Channel installation 32 Basic use 13
Channels Timers
Change 12 On timer 26
Favorite lists 24 Sleeptimer 26
Child lock 26 Volume 12
Connect Wall mount 7
EN-54
Watch
Channels 12
ENglish
Devices 12
U
Uninstall channels 34
USB device
Connect 28
Disconnect 28
V
VESA wall bracket 7
Video formats 47
Volume
Adjust 12, 21
Automatic leveling 21
Delta 21
Headphone 21
W
Wall mount TV 7
Y
Y Pb Pr 39
EN-55
© 2008 Koninklijke Philips Electronics N.V.
All rights reserved.
Document order number: 3139 125 39504