Professional Documents
Culture Documents
S/N: BCA1-99999
S/N: BDA1-99999
S/N: BBB1-99999
S/N: FDB1-99999
S/N: AGC1-99999
S/N: BEC1-99999
S/N: DMC1-99999
S/N: KEG1-99999
S/N: SHH1-99999
S/N: ASK1-99999
S/N: CBR1-99999
S/N: 5SS1-99999
S/N: 6YS1-99999
S/N: 7CS1-99999
S/N: 8AS1-99999
S/N: 9XS1-99999
S/N: AFS1-99999
S/N: 1HW1-99999
S/N: 2BW1-99999
S/N: APX1-99999
S/N: AGY1-99999
S/N: ATY1-99999
S/N: MSY1-99999
S/N: 2PZ1-99999
S/N: 4GZ1-99999
S/N: 5AZ1-99999
This diagnostic code is recorded when the ECM reads the electrical system voltage that
is at contact J1-1 as being below normal range (less than 18 volts for two seconds).
https://sis2.cat.com/#/detail?
This diagnostic code may cause the outputs of the ECM to operate incorrectly.
keyword=i01566567&tab=3&serialNumber=&infoType=4&serviceMediaNumber=RENR8398&serviceIeSystemControlNumber=i01566567
https://sis2.cat.com/#/detail?keyword=i01566567&tab=3&serialNumber=&infoType=4&serviceMediaNumber=RENR8398&serviceIeSystemControlNumber=i01566567 1/2
1/11/2021 SIS 2.0
Ensure that CID 0168 FMI F01 is on hold. The "SERV CODE" indicator is illuminated.
Expected Result:
Results:
YES - The voltage is greater than 18 DCV. This should not cause the diagnostic
code. Proceed to Test Step 2.
NO - The voltage is less than 18 DCV. The charging system is not correct.
Repair: Check the charging system. See Special Instruction, REHS0354,
"Charging System Troubleshooting".
STOP
A. Turn the disconnect switch and the key start switch to the OFF position.
C. Turn the disconnect switch and the key start switch to the ON position.
E. At machine harness connector J1 for the ECM, measure the voltage between
contact J1-1 and contact J1-2.
Expected Result:
Results:
YES - The voltage is greater 18 DCV. This should not cause the diagnostic code.
Repair: Verify that the diagnostic code is still present. If the cause of the diagnostic
code is not found, replace the ECM. See Testing And Adjusting, "Electronic Control
Module (ECM) - Replace".
STOP
NO - The voltage is less than 18 DCV. The machine harness has failed.
Repair: Check the +battery circuit and the ground circuit in the machine harness.
Inspect the connectors and clean the connectors. Repair the machine harness or
replace the machine harness.
STOP
PIP-11109658
2021/01/11
00:08:09+08:00
i01566567
© 2021 Caterpillar Inc.
Caterpillar:
Confidential Green
https://sis2.cat.com/#/detail?
keyword=i01566567&tab=3&serialNumber=&infoType=4&serviceMediaNumber=RENR8398&serviceIeSystemControlNumber=i01566567
https://sis2.cat.com/#/detail?keyword=i01566567&tab=3&serialNumber=&infoType=4&serviceMediaNumber=RENR8398&serviceIeSystemControlNumber=i01566567 2/2