00H Boot started 3FH OME init of COM and LPT ports 01H Initialize chipset 40H Configure the COM and LPT ports 02H Initialize CS 41H Initialize the floppies 03H TEST RAM 42H Initialize the hard disk 04H Move boot loader into RAM 43H Initialize option ROMs 05H Execution in RAM 44H OME's init of power management 06H Check override option 45H Update Numlock status 07H Shadow system BIOS 46H Test for coprocessor installed 08H Checksum system BIOS ROM 47H OME function before boot 09H Proceed with normal boot 48H Dispatch to OS boot 0AH Proceed with crisis boot 49H Jump into bootstrap code 0FH No memory/fatal error 50H ACPI initial CCH Proceed with crisis ROM 51H Check if S2D partition 99H Resume SMRAM not found 52H USB hub controller initial POST PCI BIOS POST CODE DESCRIPTION POST CODE DESCRIPTION 10H Signals that reset occurred D0H Check ROM signature 1X video 11H Turn off fasta20 for post D1H Enable RAM area in registers 12H signal power on reset D2H Copy ROM to RAM in registers 13H initialize the chipset D3H Update segment range attribute 14H Search for isa bus vga adapter D4H Configure memory registers 15H reset counter/timer 1 D5H Configure I/O registers 16H user register configuration through cmos D6H Configure IRQ assignment 17H size system memory D7H Turn on PCI device 18H dispatch to ram test D8H 2x Video r/w segment 19H checksum the rom D9H OME defined ROM init 1AH reset pics DAH Disable add-in ROM card decode 1BH initialize video adapter DBH PCI return(config and no Video) 1CH initialize video(6845 regs) DCH PCI Video->Enable RAM area in reg 1DH initialize color adapter DDH PCI Video-Copy ROM to RAM in reg 1EH initialize monochrome adapter DEH PCI Video-Update seg range attr 1FH test 8237a page registers DFH PCI Video-Configure memory reg 20H keyboard controller seif test E0H PCI Video-Configure I/O reg 21H rest keyboard controller E1H PCI Video-Configure IRQ 22H check if cmos ram valid E2H PCI Video-Turn on PCI devic 23H teat battery fail&cmos x-sum E3H PCI Video-2x Video r/w segment 24H test the dma controllers E4H PCI Video-OEM defined ROM init 25H initialize 8237a controllers E5H PCI Video- Dis add-in ROM card decode 26H initialize interrupt vectors E6H PCI Video-PCI return(no Video) 27H ram quick sizing(page test) E7H Look for PCI bridge device 28H safely entered protected mode E8H Search IDE controller on the PCI bus 29H completely ram test E9H Start of cardBus configuration 2AH successful exit from protected mode PNP BIOS 2BH setup shadow POST CODE DESCRIPTION 2CH going to initialize video A1H ChecK R/W status for runtime date aret 2DH search for monochrome adapter A2H Check R/W status for NVRAM dare arte 2EH search for color adapter A3H Resolve system nodes by COMS settings 2FH singn-on messages displayed A4H Init Var to PNP BOIS runtime date arte 30H oem init keyboard controller A5H Hook INT 15h 31H Test if keyboard present A6H Setup $ PnP install check in F0000 seg 32H Test keyboard interrupt A7H PNP last minute hooks for OEMs 33H Test keyboard command byte A8H Protect RT date arte & NVRAM buffer 34H TEST blank and count all RAM A9H Return from PNP initial procedure 35H Safely entered protected mode(2) SMI Handler 36H Completely RAM test POST CODE DESCRIPTION 37H Successful exit from protected mode(2) C0H SMI entry marker 38H Update keyboard controller C1H smi exit marker 39H Setup cache controller C2H apmsmi entry 3AH Test if 18.2Hz periodic working C3H apmsmi exit 3BH Test for RTC ticking C4H swsmi function execution 3CH Initialize hardware interyupt vectors C5H hwsmi function execution