Professional Documents
Culture Documents
Plug-in Type
Thanks to the flow increase, valve size can be reduced!
Saves energy and space .
New
SY3000 SY5000 SY7000
10 mm 15 mm
18 mm
ø2, ø3.2,
ø4, ø6, ø8∗
fittings are connectable.
∗ Type M10/M11 manifold
Plug-in
Page 16
Sub-plate newly added!
Up to ø63 ∗
ø80
(ø125 at 100 mm/s)
SY3000/5000
Possible to drive cylinders
New
Up to
∗
ø80
(ø160 at 100 mm/s)
∗ Values based on comparison with the existing
SMC model. For details, refer to page 1.
Power consumption
∗ Refer to Features 2.
Manifold
Side ported From page 81 Bottom ported From page 81 Top ported From page 93
Applicable protocol
DeviceNetTM
PROFIBUS DP
CC-Link
EtherNet/IPTM
EtherCAT
PROFINET
CANopen
AS-Interface
OMRON CompoBus/S
CompoNetTM
Features 1
Series SY3000/5000/7000
Power saving
Power consumption [Electrical power waveform with power saving circuit]
Applied voltage
Power consumption is
reduced by power saving
24 V
circuit.
0.1w 0.35 w
0V Power consumption is decreased by
approx. 1/3 by reducing the wattage
Standard required to hold the valve in an
0.35 (0.9) W
With power energized state. (Effective
saving circuit
0.1 (0.4) W energizing time is over 67 ms at 24
With power Standard VDC.) Refer to the electrical power
saving circuit 0W waveform as shown on the left.
67 ms (40 ms)
Wiring, piping and operation are integrated on one side. 4-position dual 3-port valve available
Multiple layer type is available as an From page 226 (Only rubber seal type)
option. This saves space in Piping • Two 3-port valves built into one body
the lateral direction.
Wiring Can be operated from the top.
A side
spool valve B side
Bottom ported is prepared. Space saving spool valve
Top or bottom ported reduces
the footprint.
• 3-port valves on the A and B sides can operate independently.
• When used as a 3-port valve, only half the number of stations is required.
• Can also be used as a 4-position, 5-port valve.
• 4-position dual 3-port valve with back pressure check valve is
available.
• Combination examples
Different sizes (SY3000/5000 or SY5000/7000) can be mixed! From page 189 Manifold overall length
Possible to reduce installation space, the number of serial units and wirings. Approx. 29%
reduced
For serial transmission SY5000 manifold SY3000 manifold Mixed manifold
EX260 SY5000 3 stations SY3000 4 stations SY5000 3 stations SY3000 4 stations
BA BA BA B A B A B A B A B A B A B A B A B A B A B A
Installation 14 A 14 A 14 A 14 A 14 A 14 A 14 A 14 A 14 A 14 A 14 A 14 A 14 A 14 A
space
12 B 12 B 12 B 12 B 12 B 12 B 12 B 12 B
12 B 12 B 12 B 12 B 12 B 12 B
2 sets 1 set
Number of
serial units
Features 2
5 Port Solenoid Valve
Improved safety
Back pressure check valve
This prevents actuator and air operated valve malfunctions caused by the exhaust from other valves.∗
Built-in valve type Back pressure check valve Retrofit or pre-installed type
(Check seal) If the product is affected by back pressure after
installation, the back pressure check
(A) (B)
4 2 valve assembly can be added. Page 232
5 1 3
5 4 1 2 3 (EA) (P) (EB)
(EA) (A) (P) (B) (EB)
New With residual pressure release valve (Only SY5000) Page 13 IP67 compliant
Indicator
For residual pressure release of [When 1(P) port is pressurized] [When 1(P) port is not pressurized]
the 3-position closed center valve When P port is not pressurized
EXH. EXH.
·The pressure of the 4 (A) and 2 (B) ports is al-
EXH. EXH.
so exhausted automatically at the same when When P port is pressurized
the pressure of the 1 (P) port is exhausted. 4 2 4 2
·The pressure can be visualized using the indicator (red).
·Since this valve is not a spacer type, the flow rate is 5 3 5 3
1 1
equivalent to that of the normal closed center valve.
SUP stop valve spacer Page 227 Double check spacer Page 227
(With residual pressure release valve) (With residual pressure release valve)
Air supply to each valve can be stopped individually. The Long time of intermediate stop and position holding are possible.
valve and cylinder can be replaced without stopping other [Intermediate stop] [Drop prevention]
devices and equipment. Button for manual release
of residual pressure Double check spacer assembly Double check spacer assembly
Button for manual release
To exhaust residual pressure
of residual pressure on cylinder side.
To exhaust residual pressure 2-position single valve
on cylinder side. 4(A)
2(B)
OFF
ON/B side
<OFF>
<ON>
Valve state
Unlocked (raised/lowered)
Piping options
Locked
To mount the piping on top To mount the piping on the side Mixed mounting of
top ported and side
Port block assembly One-touch fitting ported is possible.
for A, B port
Top ported
Replace the
Thread piping Body cover fitting and the
assembly port plug only.
Cover assembly
Side ported
Pressure switch
Port block assembly It is possible to detect the
for P, E port output of 4(A) and 2(B) port
with a pressure switch by
mounting the top ported
valve onto the side ported or
bottom ported manifold.
(Pressure switch etc., needs
Refer to page 247 for how to change piping types. to be ordered separately.)
Features 4
5 Port Solenoid Valve Variations
Wiring Manifold
Common
Connection
Circular connector
Negative common
Blanking plate
Positive common
Flat ribbon cable
D-sub connector
M12 connector
Variations
PC wiring
Lead wire
EX510
EX500
EX600
EX250
EX260
EX126
EX120
5 ports
SY303
Sub-plate
From
— — — — — — — — — — — — — — — —
Plug-in
page 18
M12 connector SY503
SY30
Bottom ported Side ported
Type
50 SY50 — — — — — — — — — —
From
page 29 P.29 P.29 P.29 P.57
SY70
Metal Base
Type
SY30
51 SY50 — — — — — — — — — —
From
page 29 P.29 P.29 P.29 P.57
SY70
Plug-in
SY33
Top ported
Type
52 SY53 — — — — — — — — — — —
From
page 49 P.49 P.49 P.49 P.67
SY73
SY30
Bottom ported Side ported
Type
Plug-in Connector Connecting Base
10 SY50 — —
From
page 81 P.81 P.81 P.81 P.99 P.109 P.119 P.129 P.137 P.149 P.157 P.165 P.173
SY70
Type
SY50
Manifold
11 — —
From
page 81 P.81 P.81 P.81 P.99 P.109 P.119 P.129 P.137 P.149 P.157 P.165 P.173
SY70
SY33
Top ported
Type
12 SY53 — — —
Plug-in
From
page 93 P.93 P.93 P.93 P.105 P.115 P.125 P.135 P.147 P.155 P.163 P.171 P.179
SY73
Standard Option Made-to-Order (Refer to page 14.)
Features 5
Series SY3000/5000/7000
Options (Pages 226 to 234) A, B Port Size Valve Options
Different pressures
Interface regulator
Enclosure IP67
C2 C3 C4 C6 C8 C10 C12
Plug (White)
Name plate
(N1) (N3) (N7) (N9) (N11)
M5 1/8 1/4
Straight piping
Straight piping
Straight piping
Straight piping
Straight piping
Straight piping
—
— — — — — — — — — — — — — — — — — — — — — — — — — —
External External
— Pilot Pilot
— —
— —
— — — — — — — — — — — — — — — — —
— — External Individual External
Pilot SUP Pilot
—
— —
— —
— — — — — — — — — — — — — — — — — — —
— — Individual
SUP
—
— —
— — —
— — — — — — — — — — — — — — — — —
— — External Individual External
Pilot SUP Pilot
—
— —
— — — — Note 2)
— — — — P.189
— — External Individual External
Pilot SUP Pilot
— — — — P.193
— — — Note 2)
— — — — — — — — — — — P.189
External Individual External
Pilot SUP Pilot
— — P.193
— —
— — Note 2)
— — — — — — — P.201
— — — External Individual External
Pilot SUP Pilot
— — — P.201
Note 1) Elbow piping may specify size only in millimeters, depending on the port size. Refer to How to Order Manifold for details.
Note 2) Refer to Manifold Specifications on page 77 for details on IP67.
Straight piping Elbow piping
One-touch fittings (Upward)
Features 6
Manifold Variations ·················································· Features 5 Valve Replacement Parts ············································ Page 11
Optimum Actuation Size Chart of Air Cylinder ·············· Page 1 With Residual Pressure Release Valve ······················ Page 13
Sub-plate
Manifold
Manifold Exploded View [Exploded View, Manifold Parts No.] ············································· Page 73
Front matter 1
Valve
Manifold
Sub-plate
Base Side ported Bottom ported Top ported
Plug-in
Plug-in Connector Connecting Base ············································································· Page 77
D-sub PC
connector wiring
D-sub Connector, Flat Ribbon Cable, PC Wiring System [IP40/67] ······························ Page 81
Flat Terminal
ribbon cable block box Terminal Block Box [IP67] ······························································································· Page 99
Metal Base
Lead wire Circular Lead Wire [IP67] ············································································································ Page 109
connector
Plug-in
Circular Connector [IP67] ······························································································ Page 119
EX500
EX500 Gateway-type Serial Transmission System [IP67] ·········································· Page 129
EX600
EX260 EX250 Integrated-type (For Input/Output) Serial Transmission System [IP67] ··········Page 149
EX260 Integrated type (For Output) Serial Transmission System [IP67] ··················· Page 157
EX126
Plug-in
Type 11/Bottom Ported Common Dimensions ··························································· Page 184
Mixed
mounting
Plug-in Manifold Mixed Mounting Type ······································································· Page 189
Manifold Exploded View [Exploded View, Manifold Parts No.] ··································· Page 206
Plug Assembly Part No.
One-touch Fittings/
Manifold Options [ Plug-in Metal Base, Plug-in Connector Connecting Base] ································································ Page 225
Front matter 2
Optimum Actuation Size Chart of Air Cylinder
Applicable Applicable cylinder
Main valve
cylinder Series
seal type
speed ø6 ø10 ø16 ø20 ø25
SY3000
SY7000
100 mm/s
or less
SY3000
SY7000
SY3000
SY7000
300 mm/s
or less
SY3000
SY7000
SY3000
SY7000
500 mm/s
or less
SY3000
SY7000
[Common conditions]
• Pressure: 73 psi (0.5 MPa)
• Piping length: 1 m
• Load ratio: 50%
• Stroke: 200 mm
Connector type manifold (for side and bottom ported type)
∗ Use as a guide for selection.
Please check the actual conditions with SMC Model Selection Software.
1
ø32
ø40
ø50
ø63
ø80
Applicable cylinder
ø100
ø125
ø140
ø160
2
One-touch Fittings/ Type 10, 11, 12 Type 50, 51, 52
Manifold Options Plug-in Connector Connecting Base Plug-in Metal Base Plug-in Sub-plate Valve
Plug Assembly Part No. Manifold Exploded View Manifold Exploded View
Series SY3000/5000/7000
Valve Specifications
Valve Specifications
3
Valve Specifications Series SY3000/5000/7000
Valve
Response Time
Sub-plate
Response time (ms)
Standard Quick response type
Series Seal type Model Type of actuation Without light/ With light/surge Without light/ With light/surge
surge voltage voltage suppressor surge voltage voltage suppressor
Plug-in
suppressor S/Z type R/U type suppressor S/Z type R/U type
Rubber seal SY310 15 or less 20 or less 15 or less 12 or less 15 or less 12 or less
2-position single
Metal seal SY311 15 or less 20 or less 15 or less 12 or less 15 or less 12 or less
Rubber seal SY320 12 or less 15 or less 12 or less 10 or less 13 or less 10 or less
2-position double
SY3000 Metal seal SY321 12 or less 15 or less 12 or less 10 or less 13 or less 10 or less
Rubber seal SY33/4/50 18 or less 22 or less 18 or less 14 or less 18 or less 14 or less
3-position
Metal seal SY33/4/51 18 or less 22 or less 18 or less 14 or less 18 or less 14 or less
Metal Base
Rubber seal SY3A/B/C0 4-position dual 3-port valve 18 or less 22 or less 18 or less 15 or less 19 or less 15 or less
Rubber seal SY510 24 or less 31 or less 24 or less 18 or less 25 or less 18 or less
2-position single
Metal seal SY511 24 or less 31 or less 24 or less 18 or less 25 or less 18 or less
Rubber seal SY520 12 or less 15 or less 12 or less 10 or less 13 or less 10 or less
2-position double
Plug-in
SY5000 Metal seal SY521 12 or less 15 or less 12 or less 10 or less 13 or less 10 or less
Rubber seal SY53/4/50 30 or less 34 or less 30 or less 24 or less 28 or less 24 or less
3-position
Metal seal SY53/4/51 28 or less 30 or less 28 or less 23 or less 25 or less 23 or less
Rubber seal SY5A/B/C0 4-position dual 3-port valve 35 or less 42 or less 35 or less 28 or less 35 or less 28 or less
Rubber seal SY710 47 or less 58 or less 53 or less 42 or less 52 or less 44 or less
4
Series SY3000/5000/7000
Valve Weight
Series SY3000
Valve model Seal type Type of actuation Weight g Valve model Seal type Type of actuation Weight g
Single 74 Single 76
2-position 2-position
Double 83 Double 86
Closed center SY301 Metal seal Closed center
SY300 Rubber seal
3-position Exhaust center 87 3-position Exhaust center 90
Pressure center Pressure center
4-position Dual 3-port valve 83
Series SY5000
Valve model Seal type Type of actuation Weight g Valve model Seal type Type of actuation Weight g
Single 82 Single 91
2-position 2-position
Double 90 Double 101
Closed center SY501 Metal seal Closed center
SY500 Rubber seal
3-position Exhaust center 3-position Exhaust center
100 111
Pressure center Pressure center
4-position Dual 3-port valve 90
5
Valve Specifications Series SY3000/5000/7000
Valve
Valve Weight
Series SY7000
Valve model Seal type Type of actuation Weight g Valve model Seal type Type of actuation Weight g
Single 110 Single 122
2-position 2-position
Double 118 Double 133
SY701
Sub-plate
Closed center Metal seal Closed center
SY700 Rubber seal
3-position Exhaust center 133 3-position Exhaust center 150
Pressure center Pressure center
4-position Dual 3-port valve 114
Plug-in
Seal Port size Weight Seal Port size Weight
Valve model Type of actuation Valve model Type of actuation
type 4, 2 (A, B) g type 4, 2 (A, B) g
Single 125 Single 136
2-position 2-position
Double 133 Double 148
SY730-02 Closed center
1/4
SY731-02 Closed center 1/4
3-position Exhaust center 147 3-position Exhaust center 164
Pressure center Pressure center
4-position Dual 3-port valve 129 Single 174
2-position
Single 163 Double C6 186
2-position
SY731-C6
Metal Base
Double 171 Closed center ø6 One-touch
C6
Closed center 3-position Exhaust center fitting 202
SY730-C6 ø6 One-touch
3-position Exhaust center 186 Pressure center
fitting
Pressure center Single 162
2-position
4-position Dual 3-port valve 167 Double C8 174
Metal
Single 151 SY731-C8 Closed center ø8 One-touch
Plug-in
2-position seal
Double 159 3-position Exhaust center fitting 190
C8
Rubber Closed center Pressure center
SY730-C8 seal ø8 One-touch
3-position Exhaust center 174 Single 148
fitting 2-position
Pressure center Double C10 159
4-position Dual 3-port valve 155 SY731-C10 Closed center ø10 One-touch
Single 136 3-position Exhaust center fitting 176
Plug-in
Manifold Exploded View
Type 10, 11, 12
Plug Assembly Part No.
One-touch Fittings/
Manifold Options
6
Series SY3000/5000/7000
Valve Construction
Rubber Seal
2-position single Top ported
(A) (B)
4 2
t e q w r t e q w r
2-position single
5 4 1 2 3 5 1 3 (A)4 2(B)
(EA) (A) (P) (B) (EB) (EA) (P) (EB)
(EA)5 1 3(EB)
(P)
2-position double
t e q w r
2-position double
5 4 1 2 3 (A)4 2(B)
(EA) (A) (P) (B) (EB)
(EA)5 1 3(EB)
(P)
(EA)5 1 3(EB)
(P)
Component Parts
No. Description Material Note
SY3000: Zinc die-casted
1 Body
SY5000/SY7000: Aluminum die-casted
Special resin/HNBR
( )
2 Spool valve 3-position valve:
Aluminum/HNBR
3 Piston Resin
Body cover assembly Resin For side/bottom ported
SY3000: Resin
4
Port block assembly SY5000: Zinc die-casted For top ported
SY7000: Aluminum die-casted
5 Pilot valve assembly — Refer to page 12.
7
Valve Construction Series SY3000/5000/7000
Valve
Rubber Seal
4-position dual 3-port valve
4-position dual 3-port valve
N.C. valve x 2 pcs. N.O. valve x 2 pcs.
t e q w r 4(A) 2(B) 4(A) 2(B)
Sub-plate
Plug-in
5(EA) 1(P) 3(EB) 5(EA) 1(P) 3(EB)
N.C. valve, N.O. valve 1 pc. of each
5 4 1 2 3 4(A) 2(B)
(EA) (A) (P) (B) (EB)
Metal Base
5(EA) 1(P) 3(EB)
2-position double with back pressure check valve (Built-in valve type)
Plug-in
t e q w r
2-position double
with back pressure check valve
(A)4 2(B)
Plug-in
Manifold Exploded View
Type 10, 11, 12
5(EA) 1(P) 3(EB) 5(EA) 1(P) 3(EB)
5 4 1 2 3 N.C. valve, N.O. valve 1 pc. of each
(EA) (A) (P) (B) (EB)
4(A) 2(B)
Plug Assembly Part No.
One-touch Fittings/
∗ The built-in valve type back pressure check valve is not available for the SY7000.
Manifold Options
8
Series SY3000/5000/7000
Metal Seal
2-position single Top ported
(A) (B)
4 2
t e q w r t e q w r
2-position single
5 4 1 2 3 5 1 3 (A)4 2(B)
(EA) (A) (P) (B) (EB) (EA) (P) (EB)
(EA)5 1 3(EB)
(P)
2-position double
t e q w r
2-position double
5 4 1 2 3 (A)4 2(B)
(EA) (A) (P) (B) (EB)
(EA)5 1 3(EB)
(P)
(EA)5 1 3(EB)
(P)
Component Parts
No. Description Material Note
SY3000: Zinc die-casted
1 Body
SY5000/SY7000: Aluminum die-casted
2 Spool, Sleeve Stainless steel/HNBR
3 Piston Resin
Body cover assembly Resin For side/bottom ported
SY3000: Resin
4
Port block assembly SY5000: Zinc die-casted For top ported
SY7000: Aluminum die-casted
5 Pilot valve assembly — Refer to page 12.
9
10
One-touch Fittings/ Type 10, 11, 12 Type 50, 51, 52
Manifold Options Plug-in Connector Connecting Base Plug-in Metal Base Plug-in Sub-plate Valve
Plug Assembly Part No. Manifold Exploded View Manifold Exploded View
Series SY3000/5000/7000
Valve Replacement Parts
How to Order Port Block Assembly
Mounting screw
SY 0V 6A One-touch fitting
11
Valve Replacement Parts Series SY3000/5000/7000
Valve
Body Cover Assembly
∗ Used when the top ported is changed to the side or bottom ported.
Mounting screw
Sub-plate
Part no.
Series Standard (Valve mounting screw Valve mounting screw
“not” falling-out-prevention type) falling-out-prevention type
Internal pilot SY30V-16A SY30V-16A-1
Plug-in
SY3000
External pilot SY30V-16AR SY30V-16AR-1
Internal pilot SY50V-16A SY50V-16A-1
SY5000
External pilot SY50V-16AR SY50V-16AR-1
Internal pilot SY70V-16A SY70V-16A-1
SY7000
External pilot SY70V-16AR SY70V-16AR-1
∗ The part number is not indicated on the product.
Metal Base
Plug-in
How to Order Pilot Valve Assembly (With a gasket and two mounting screws)
Coil type
Nil Standard q
Socket
w
T With power saving circuit
b-side pilot valve
Rated voltage
Plug-in
5 24 VDC B tight flat head screw (M1.7)
Tightening torque: 0.09 lbf·ft (0.12 N·m) Pilot valve mounting screw (M2 x 16.5)
6 12 VDC
Tightening torque: 0.11 lb·ft (0.15 N·m)
12
Series SY5000 RoHS
SY 5 3 0 0 5 U D 1 E
Series With residual pressure release valve
5 SY5000 E With residual pressure release valve∗
∗ Mounting screw types, hexagon socket head cap
Type of actuation Base mounted screw B and screw falling-out-prevention type K,
3 3-position closed center∗ (Top ported is not available.) H are not available.
∗ Only closed center type is available. Protective class
class (Mark: )
Nil Standard U
T With power saving circuit (Continuous duty type) S — Positive
∗ Be sure to select the power saving circuit type when the Z common
∗ Refer to page 14 for with the safety slide locking
valve is continuously energized for long periods of time. NS — Negative
∗ Be careful of the energizing time when the power saving manual override.
NZ common
circuit is selected. Refer to page 244 for details.
∗ Only “Z” and “NZ” types are available for with the
power saving circuit.
Symbol
Valve Specifications <When 1(P) port is <When 1(P) port is
not pressurized> pressurized>
Rubber seal Metal seal
Valve construction EXH. EXH.
3-position closed center valve with residual pressure release valve Note 1)
EXH. EXH.
Fluid Air
44 to 102 (0.3 to 0.7) 4 2 4 2
Operating pressure range psi MPa Note 2) 44 to 102 (0.3 to 0.7) (High pressure: 44 to 145 (0.3 to 1))
Weight g 117 128
5 3 5 3
Note 1) Rubber seal is used for the residual pressure release valve. 1 1
Note 2) Internal pilot type only A mechanism is used that exhausts the pressure of the
Note 3) Other specifications are common to the valve specifications on page 3. cylinder port when the P port supply pressure of the 3
position closed center valve is exhausted.
Dimensions
(Light/surge voltage suppressor)
116.6
Manual override 84.5
( ) 39.8 30.7
12.6
Exhausted: Concave
62.3 (For F type)
(For E type: 60.2)
30.1
Valve
Please contact SMC for detailed dimensions, specifications and lead times.
Symbol
1 Main Valve Fluororubber Specification
Sub-plate
-X90
Fluororubber is used for rubber parts of the main valve to allow use in applications such as the following.
Plug-in
· When using a lubricant other than the recommended turbine oil, and there is a possibility of malfunction due to swelling of the spool valve seals.
Applicable valves series SY3 03 0, SY5 03 0, SY7 03 0 (Only rubber seal type)
3 0
SY 5 3 0 1 X90
7
Metal Base
Entry is the same as standard products.
Specifications and performance are the same as standard products.
Plug-in
Symbol
2 With Safety Slide Locking Manual Override -X13
Symbol
3 Metal Seal Valve, Main/Pilot Valve Common Exhaust -X16
Plug-in
This is the type where the exhaust method of the pilot valve is integrated into the exhaust port of the main valve.
3
14
15
Plug-in
[IP67 Compliant]
Sub-plate Type
16
One-touch Fittings/ Type 10, 11, 12 Type 50, 51, 52
Manifold Options Plug-in Connector Connecting Base Plug-in Metal Base Plug-in Sub-plate Valve
Plug Assembly Part No. Manifold Exploded View Manifold Exploded View
Series SY3000/5000
Plug-in Sub-plate Type [IP67 Compliant]
(Side ported, Bottom ported, Top ported)
17
Series SY3000/5000
Sub-plate Type [IP67 Compliant]
Plug-in
(Side ported, Bottom ported, Top ported)
Valve
RoHS
How to Order
In the case of Valve + Sub-plate (Built-in valve type part no.)
Sub-plate
SY 3 1 0 0 5 U D 1 C6 W1 01
Plug-in
Light/surge voltage suppressor A, B port thread type
Series and common specification (Top ported valve only)
3 SY3000 Surge voltage Common Nil Rc
Symbol With light
5 SY5000 suppressor specification F G
Nil — — N NPT
Type of actuation R — Non-polar T NPTF
Metal Base
1 Single U
∗ Only Nil is available for M5.
2-position
2 Double S — Positive
3 Closed center Z
common Type of mounting screw
4 3-position Exhaust center NS — Negative Nil Round head combination screw
5 Pressure center NZ common B Hexagon socket head cap screw
Plug-in
A∗ N.C./N.C. ∗ Only “Z” and “NZ” types are available for with the K
Round head combination screw
4-position
B∗ dual 3-port N.O./N.O. power saving circuit.
(Falling-out-prevention type)
C∗ N.C./N.O. H Hexagon socket head cap screw
∗ Only rubber seal type is available for the Manual override (Falling-out-prevention type)
4-position dual 3-port valve. Nil: D: ∗ For “K” and “H”, the valve body cover has a drop
Plug-in
valve is not available for the 3-position type. A, B port size (∗Top ported valve only) W7 With M12 connector cable (5000 mm)
Thread piping ∗ When ordering a product with M12 connector
Pilot valve option Symbol Port size Applicable series
cable, the connector cable is included.
02 1/4 SY5000
One-touch Fittings/
5 24 VDC
6 12 VDC
Note) When mounting a special order (including Made-to-Order specification) valve on the sub-plate, add the valve part number under the sub-plate part number to
place an order. For details, refer to the ordering example on page 19.
18
Series SY3000/5000
How to Order
q Part no.
No. Description Note
SY3000 SY5000
Round head SY3000-23-24A SY5000-221-1A
Valve combination screw (M2 x 32) (M3 x 32.5) Part numbers shown on
q mounting the left are for 10 valves
screw Hexagon socket SY3000-222-1A SY5000-222-1A (20 pcs.).
head cap screw (M2 x 32) (M3 x 32.5)
Base gasket Part numbers shown on the
w (for sub-plate) SY30M-11-1A SY50M-11-1A left are for 10 valves (10 pcs.).
ZS-37-L Cable length: 300 mm
w ZS-37-M Cable length: 500 mm
M12 waterproof
e connector cable ZS-37-N Cable length: 1000 mm
ZS-37-P Cable length: 2000 mm
ZS-37-C Cable length: 5000 mm
e Caution
Tightening torque
M2: 0.12 (0.16 N·m) (SY3000)
M3: 0.59 (0.8 N·m) (SY5000)
19
Series SY3000/5000
Plug-in Sub-plate Type [IP67 Compliant]
(Side ported, Bottom ported, Top ported)
Valve
Plug-in Side Ported
Dimensions: Series SY3000 Sub-plate Top Ported
14.5 13.3
SY3001 -1-W-01 (Side ported) For "F" marking 1/8
Sub-plate
(Thread type) [4(A), 2(B) port]
12
19
F
Plug-in
Manual override 83.2
(
Push-turn locking slotted type:
Press, then rotate it. ) 51.1
34.5 8.8 2 x ø3.2
4(A) port side: Blue (For rubber seal) (For mounting)
: Gray (For metal seal)
Metal Base
4A 2B
2(B) port side: Yellow
35.9
32.9
BA
14 A
12 B
PE X
(Light/surge voltage suppressor) 5EA 1P 3EB
10.6
(42.1)
Plug-in
52.2 5.8
11.9
67.9 (15.3)
(For 3-position)
1/8
[1(P) port]
28
19.5
17.7
20
Sub-plate side pin arrangement Triangle mark
7.4
(No numeric indication)
M5 x 0.8 M5 x 0.8
COM. (PE: External pilot EXH port) (X: External pilot port)
1/8 11 11 9.5
Plug-in
F
4A 2B
B A
4 A
2B
PE X
(Light/surge voltage suppressor) 5EA 1P 3EB
Plug Assembly Part No.
One-touch Fittings/
Plug-in
Dimensions: Series SY3000 Sub-plate Bottom Ported
SY3001 -1-W-B01 (Bottom ported)
For "F" marking
Plug
(Thread type)
19
F
( )
(Max. 3)
Push-turn locking slotted type: 51.1
Press, then rotate it. 34.5 8.8 2 x ø3.2
4(A) port side: Blue (For rubber seal) (For mounting)
: Gray (For metal seal) 4A 2B
2(B) port side: Yellow
35.9
32.9
B A
14 A
12 B
PE X
(Light/surge voltage suppressor) 5EA 1P 3EB
10.6
(42.1)
52.2 5.8
(Max. 3)
11.9
Sub-plate side pin arrangement 67.9 (15.3)
(No numeric indication) (For 3-position)
COM.
58.6
Unused (Without terminal)
28
19.5
20
Panel fitting dimensions
Triangle mark Plug M5 x 0.8
M5 x 0.8 28.6 5.2 (X: External pilot port)
(PE: External pilot EXH port) Plug
32.5
3.7
14.7
13 13 7.5
8.2
3.5
29.5
5 3 1
28.3
34.5 2 x M3
2 x ø3.4 4 2
42.5 1/8
[1(P), 2(A), 4(B), 5(EA), 3(EB) port] Fitting dimensions for panel mounting
14.5 13.3 Refer to panel fitting dimensions
for details.
21
Series SY3000/5000
Plug-in Sub-plate Type [IP67 Compliant]
(Side ported, Bottom ported, Top ported)
Valve
Plug-in Side Ported
Dimensions: Series SY5000 Sub-plate Top Ported
SY5001 -1-W-02 (Side ported)
For "F" marking 1/4
Sub-plate
46.4 10.8
(Thread type) [4(A), 2(B) port]
M5 x 0.8 18 25 M5 x 0.8
(PE: External pilot EXH port) (X: External pilot port)
15.5
Plug-in
13
17.5
F
(
Push-turn locking slotted type:
Press, then rotate it. ) 2 x ø4.3 71.3
Metal Base
(For mounting) 62 7.4
4(A) port side: Blue (For rubber seal)
: Gray (For metal seal) PE 4A 2B X
2(B) port side: Yellow
32
40
B A
14 A
12 B
(Light/surge voltage suppressor)
Plug-in
5EA 1P 3EB
4
10.6
(42.1)
74.6 3.4
11.9
90.3 (16.6)
(For 3-position)
58.6
2: White (SOL.b) 4: Black (SOL.a)
3
4 2
28
15.5
SOL.a SOL.b
13
1
Plug-in
Manifold Exploded View
Type 10, 11, 12
(Max. 3)
2 B
5EA 1P 3EB
[4(A), 2(B) port] (For threaded type) (For threaded type) [4(A), 2(B) port]
Applicable tube O.D.: ø4, ø5/32"
ø6, ø1/4"
ø8, ø5/16"
(For 01 threaded type)
(76.7)
(62.3)
Manifold Options
Plug-in
Dimensions: Series SY5000 Sub-plate Bottom Ported
SY5001 -1-W-B02 (Bottom ported)
For "F" marking
(Thread type) 46.4 10.8
M5 x 0.8 M5 x 0.8
Plug
(PE: External pilot EXH port) (X: External pilot port)
15.5
17.5
F
103.4
Manual override
71.3
(Max. 3)
(Push-turn locking slotted type:
Press, then rotate it. ) 2 x ø4.3
(For mounting)
62 7.4
4(A) port side: Blue (For rubber seal)
: Gray (For metal seal) PE 4A 2B X
2(B) port side: Yellow
(Max. 3)
32
40
B A
14 A
12 B
(Light/surge voltage suppressor) 5EA 1P 3EB
4
10.6
(42.1)
74.6 3.4
11.9
90.3 (16.6)
(For 3-position)
58.6
3
4
28
2
15.5
SOL.a 1 SOL.b
Panel fitting dimensions
Triangle mark Plug
2 x M4
Unused (Without terminal)
2 x ø4.5
Fitting dimensions for panel mounting
Refer to panel fitting dimensions
4.5
32
40
for details.
18 18 16
3.5 57
4
30.5
62
9.5
5 1 3
4 2
1/4 18 25
[1(P), 2(A), 4(B), 5(EA), 3(EB) port]
23
24
One-touch Fittings/ Type 10, 11, 12 Type 50, 51, 52
Manifold Options Plug-in Connector Connecting Base Plug-in Metal Base Plug-in Sub-plate Valve
Plug Assembly Part No. Manifold Exploded View Manifold Exploded View
25
Plug-in
Bottom ported
Side ported
Top ported
Metal Base
26
One-touch Fittings/ Type 10, 11, 12 Type 50, 51, 52
Manifold Options Plug-in Connector Connecting Base Plug-in Metal Base Plug-in Sub-plate Valve
Plug Assembly Part No. Manifold Exploded View Manifold Exploded View
Series SY3000/5000/7000 Type 50, 51, 52
Plug-in Metal Base
Manifold Specifications
M5 x 0.8, 1/8
SY3000 ø2 One-touch fitting, ø3.2 One-touch fitting, ø4 One-touch fitting, ø6 One-touch fitting
ø1/8" One-touch fitting, ø5/32" One-touch fitting, ø1/4" One-touch fitting
Port size
1/8, 1/4
4(A), 2(B) port SY5000 ø4 One-touch fitting, ø6 One-touch fitting, ø8 One-touch fitting
ø5/32" One-touch fitting, ø1/4" One-touch fitting, ø5/16" One-touch fitting
1/4
SY7000 ø6 One-touch fitting, ø8 One-touch fitting, ø10 One-touch fitting, ø12 One-touch fitting
ø1/4" One-touch fitting, ø5/16" One-touch fitting, ø3/8" One-touch fitting
27
50, 51, 52
Series SY3000/5000/7000
Type
Valve
Manifold Flow-rate Characteristics Note 1)/Manifold Weight
Valve Seal Type: Rubber Seal
Sub-plate
Port size Valve flow-rate characteristics Weight: W [g] Note 2)
Model 1, 5, 3 4, 2 1→4/2 (P→A/B) 4/2→5/3 (A/B→E) (n: stations)
(P, EA, EB) (A, B) C [dm3/(s·bar)] b C [dm3/(s·bar)] b Fixed: C Replaceable: KC
Plug-in
SS5Y3-50 (Side ported) 1/8 C6 1.1 0.19 1.1 0.15 39n + 247 43.5n + 247
SS5Y3-51 (Bottom ported) 1/8 C6 1.2 0.31 1.2 0.14 41.5n + 251 48.5n + 251
SS5Y3-52 (Top ported) 1/8 C6 1.1 0.29 1.2 0.20 44n + 247
SS5Y5-50 (Side ported) 1/4 C8 2.6 0.28 2.6 0.14 93n + 379 110n + 379
SS5Y5-51 (Bottom ported) 1/4 C8 2.7 0.35 2.8 0.20 93n + 413 113n + 413
SS5Y5-52 (Top ported) 1/4 C8 2.6 0.26 3.1 0.13 103n + 379
Metal Base
SS5Y7-50 (Side ported) 3/8 C10 3.8 0.27 4.0 0.20 144n + 510 158n + 510
SS5Y7-51 (Bottom ported) 3/8 C10 4.1 0.34 4.8 0.20 150n + 549 172n + 549
SS5Y7-52 (Top ported) 3/8 C10 4.5 0.27 4.9 0.24 164n + 510
Plug-in
Valve Seal Type: Metal Seal
Port size Valve flow-rate characteristics Weight: W [g] Note 2)
Model 1, 5, 3 4, 2 1→4/2 (P→A/B) 4/2→5/3 (A/B→E) (n: stations)
(P, EA, EB) (A, B) Fixed: C Replaceable: KC
Plug-in
Manifold Exploded View
Type 10, 11, 12
Plug Assembly Part No.
One-touch Fittings/
Manifold Options
28
Type 50
Side Ported
Plug-in Metal Base RoHS
D-sub Connector Flat Ribbon Cable PC Wiring
Type 51
Bottom Ported
Series SY3000/5000/7000
How to Order Manifold
SS5Y 3 50 F 1 05 D C6
Series Type Connector type
3 SY3000 50 Side ported F: D-sub connector P: Flat ribbon cable PG: Flat ribbon cable
5 SY5000 51 Bottom ported (25 pins) (26 pins) (20 pins)
7 SY7000 50R Side ported, External pilot
∗ External pilot is not available for
the bottom ported type.
Wiring type
Nil All double wiring Note 1)
S All single wiring Note 2)
How to Order Manifold Assembly Note 1) All double wiring: 2-position single, double, 3-position and 4-position
valves can be used on all manifold stations.
Note 2) All single wiring: Available only for the manifold which has 2-position
Example (SS5Y3-50F2-) single for all stations.
2-position double (24 VDC) Note that 2-position double, 3- or 4-position valves cannot be used.
2-position single (24 VDC)
SY3200-5U1 (1 set) Note 3) If a mix of single and double wiring is required, it is supplied as a
SY3100-5U1 (3 sets)
3-position closed special order.
center (24 VDC)
SY3300-5U1 (1 set)
Valve stations
F: D-sub connector (25 pins) P: Flat ribbon cable (26 pins) PG: Flat ribbon cable (20 pins)
Symbol Stations Note Symbol Stations Note Symbol Stations Note
ide 02 2 stations All 02 2 stations All 02 2 stations All
Us
double double double
s
SS5Y3-50F2-05D-C6
1
Valve
Sub-plate
P, E port entry A, B port size
Plug-in
U U side Note 1) Thread piping
D D side Note 1, Note 2) Symbol A, B port SY3000 SY5000 SY7000
B Both sides M5 M5 x 0.8 — —
Note 1) Plugs are mounted on the opposite 01 1/8 —
side of the selected ports. 02 1/4 —
Note 2) Only D side is available for Type 51
(Bottom ported). One-touch fitting (Metric)
Metal Base
Symbol A, B port SY3000 SY5000 SY7000
Thread type C2 ø2 — —
Nil Rc C3 ø3.2 — —
F G C4 ø4 —
Fixed
Plug-in
N NPT C6 ø6 —
T NPTF C8 ø8 —
C10 ø10 — —
Mounting KC2 ø2 — — Type 50 Type 51
Nil Direct mounting KC3 (Side ported) (Bottom ported)
···
N7 ø1/4" —
N9 ø5/16" —
N11 ø3/8" — —
Plug-in
KN1 ø1/8" — — Type 50 Type 51
(Side ported) (Bottom ported)
KN3 ø5/32" —
Replaceable
Protective class
class III (Mark: )
30
Series SY3000/5000/7000
How to Order Valves (With mounting screw) Refer to page 3 for valve specifications.
SY 3 1 0 0 5 1
Base mounted
Protective class
class ΙΙΙ (Mark: )
31
Plug-in Metal Base Series SY3000/5000/7000
Valve
Plug-in Type 50/Side Ported
U M5 D side U side
SS5Y3-50(R)F 12 - Stations D - KC
C, N (D)
, KN L3
Sub-plate
B
5.3 L4
(DIN rail mounting hole pitch: 12.5)
Manual override
(Pitch)
JIS-X-5101
( ) DIN rail holding screw 45.1 P = 10.5 (
Push-turn locking slotted type:
)
Plug-in
Applicable connector: D-sub equivalent Press, then rotate it.
MIL-C-24308 (For DIN rail mounting)
14 24.1 4(A) port side : Blue (For rubber seal)
(Light/surge : Gray (For metal seal)
M5 x 0.8 (External pilot) DIN rail bracket mounting screw (7.9) voltage 2(B) port side : Yellow
[Pilot EXH port] (For DIN rail mounting) suppressor)
DIN rail
(Connector entry
upward direction) B A B A B A B A B A
92.7
Metal Base
14 A 14 A 14 A 14 A 14 A
89
PE
5EA
16.8 17.2
15.9 16.2
79
5.5
64.4
35
56.9
21.8 16
1P
29.8
35
26.6
X
12 B 12 B 12 B 12 B 12 B
3EB
4 x ø4.5
Plug-in
8.6 2 x M2.6
(For mounting) 4 L2 8
)
2 x 4-40 UNC
Replaceable: 7.7
14.5 (L5)
[For N or T thread] L1
22.1
Fixed: 4.1
manual override)
(Slide locking
[1(P), 5(EA), 3(EB) port]
(68.7)
68.3
62.6
M5 x 0.8 (External pilot)
54.7
2B 2B
[External pilot port]
7.1
32
22.6
4A 4A
50RF12 - Stations UD
7.5
Plug-in
Port size M5 One-touch fitting (Replaceable)
7.1
32
32
22.6
22.6
4A 4A
M5 x 0.8
6.6 (Pitch)
[4(A), 2(B) port] P = 10.5
(Pitch) 48.4
41.8 P = 10.5
Plug Assembly Part No.
One-touch fitting
One-touch Fittings/
n: Stations 2 3 4 5 6 7 8 9 10 11 12
Manifold Options
L1 71.5 82 92.5 103 113.5 124 134.5 145 155.5 166 176.5
L2 63.5 74 84.5 95 105.5 116 126.5 137 147.5 158 168.5
L3 98 110.5 123 135.5 148 160.5 160.5 173 185.5 198 210.5
L4 87.5 100 112.5 125 137.5 150 150 162.5 175 187.5 200
L5 13.5 14.5 15.5 16.5 17.5 18.5 13 14 15 16 17
32
Series SY3000/5000/7000
U
SS5Y3-50(R)F 12 - Stations -D01(D)
B
D side U side
L3
5.3 L4
(DIN rail mounting hole pitch: 12.5)
Manual override
Applicable connector: D-sub ( JIS-X-5101
MIL-C-24308
equivalent ) DIN rail holding screw 45.1
(Pitch)
P = 12.5 (
Push-turn locking slotted type:
Press, then rotate it. )
(For DIN rail mounting) 14 24.1
M5 x 0.8 (External pilot) 4(A) port side : Blue (For rubber seal)
(Light/surge
DIN rail bracket mounting screw (7.9) : Gray (For metal seal)
[Pilot EXH port] voltage
suppressor) 2(B) port side : Yellow
(For DIN rail mounting)
DIN rail
(Connector entry B A B A B A B A B A
upward direction)
92.7
14 A 14 A 14 A 14 A 14 A
5EA
89
PE
16.8 17.2
15.9 16.2
79
5.5
64.4
35
56.9
21.8 16
1P
29.8
35
X
26.6
12 B 12 B 12 B 12 B 12 B
3EB
1/8
manual override)
(Slide locking
[1(P), 5(EA), 3(EB) port]
(68.7)
68.3
62.6
M5 x 0.8 (External pilot)
54.7
2B 2B
[External pilot port]
7.1
32
22.6
4A 4A
mounting)
7.5
(Pitch)
50RF 12 - Stations U
D 1/8
11.8
41.8 P = 12.5
[4(A), 2(B) port]
3
[Plug for external pilot]
2B
Note) These figures show the “SS5Y3-50F2-05B-01”.
4A
n: Stations 2 3 4 5 6 7 8 9 10 11 12
L1 76 88.5 101 113.5 126 138.5 151 163.5 176 188.5 201
L2 68 80.5 93 105.5 118 130.5 143 155.5 168 180.5 193
L3 110.5 123 135.5 148 160.5 173 185.5 198 210.5 223 235.5
L4 100 112.5 125 137.5 150 162.5 175 187.5 200 212.5 225
L5 17.5 17.5 17.5 17.5 17.5 17.5 17.5 17.5 17.5 17.5 17.5
33
Plug-in Metal Base Series SY3000/5000/7000
Valve
Plug-in Type 50/Side Ported
U 01
SS5Y5-50(R)F12 - Stations - D C, N
B KC, KN
(D) D side
L3
U side
Sub-plate
5.3 L4 Manual override
Applicable connector: D-sub ( JIS-X-5101
MIL-C-24308 )
equivalent
DIN rail holding screw
(DIN rail mounting hole pitch: 12.5)
(Pitch) (
Push-turn locking slotted type:
Press, then rotate it. )
(For DIN rail mounting) 50 P = 16 (Light/surge
Plug-in
4(A) port side : Blue (For rubber seal)
M5 x 0.8 (External pilot) 16 24.1 voltage : Gray (For metal seal)
[Pilot EXH port] DIN rail bracket mounting screw suppressor) 2(B) port side : Yellow
(7.9)
(For DIN rail mounting)
DIN rail
(Connector entry B A B A B A B A B A
14 A 14 A 14 A 14 A 14 A
PE
5EA
upward direction)
106.2
5.5
23.2
116.6
96.2
35
20
Metal Base
81.6
20
74.1
1P
24.6
20
52.2
43.8
40.2
3EB
8
30.2
X
12 B 12 B 12 B 12 B 12 B
Plug-in
4 x ø4.5
12.3 (For mounting) 5 L2
)
Replaceable: 8.5
2 x M2.6
18 (L5) L1
2 x 4-40 UNC
[For N or T thread]
Fixed: 4.9
28
6.1 (Station 1) ----------- (Station n)
34
(Slide locking
[1(P), 5(EA), 3(EB) port]
(74.7)
74.3
68.6
60.7
7.8
38
27.3
4A
50RF 12 - Stations U 4A
D
10
14.3
[Plug for external pilot] 45.8 P = 16
2B
One-touch fitting
4A [4(A), 2(B) port]
Applicable tube O.D.: ø4, ø5/32"
: ø6, ø1/4"
: ø8, ø5/16"
∗ The above drawing shows when P, E
port entry is D. Note) These figures show the “SS5Y5-50F2-05B-C8”.
Plug-in
Port size 01 One-touch fitting (Replaceable)
38
38
27.3
27.3
4A 4A
8.4 (Pitch)
(Pitch)
51.6 P = 16
45.8 P = 16
Plug Assembly Part No.
One-touch fitting
One-touch Fittings/
n: Stations 2 3 4 5 6 7 8 9 10 11 12
Manifold Options
L1 84 100 116 132 148 164 180 196 212 228 244
L2 74 90 106 122 138 154 170 186 202 218 234
L3 110.5 135.5 148 160.5 173 198 210.5 223 248 260.5 273
L4 100 125 137.5 150 162.5 187.5 200 212.5 237.5 250 262.5
L5 13.5 18 16 14.5 12.5 17 15.5 13.5 18 16.5 14.5
34
Series SY3000/5000/7000
U
SS5Y5-50(R)F 12- Stations D -02(D)
B
D side U side
L3
5.3 L4
Applicable connector: D-sub ( JIS-X-5101
MIL-C-24308 )
equivalent (DIN rail mounting hole pitch: 12.5) Manual override
DIN rail holding screw
(For DIN rail mounting) 50
(Pitch)
P = 17.5
(
Push-turn locking slotted type:
Press, then rotate it. )
M5 x 0.8 (External pilot) (Light/surge 4(A) port side : Blue (For rubber seal)
[Pilot EXH port] DIN rail bracket mounting screw 16 24.1 voltage : Gray (For metal seal)
(For DIN rail mounting) suppressor) 2(B) port side : Yellow
DIN rail
(Connector entry B A B A B A B A B A
upward direction) 14 A 14 A 14 A 14 A 14 A
PE
5EA
106.2
5.5
23.2
116.6
96.2
35
20
81.6
20
74.1
1P
24.6
20
52.2
43.8
40.2
3EB
8
30.2
X
12 B 12 B 12 B 12 B 12 B
4 x ø4.5
12.3
(For mounting) 5 L2
18 2 x M2.6 (L5) L1
28 2 x 4-40 UNC
[For N or T thread]
34 6.1 (Station 1) ------------- (Station n)
1/4
manual override)
[1(P), 5(EA), 3(EB) port]
(Slide locking
(74.7)
74.3
68.6
60.7
2B 2B
[External pilot port] 9.8
38
4A 4A 27.3
10
mounting)
(Pitch)
[4(A), 2(B) port] 14.3
50RF12 - Stations U
D
45.8 P = 17.5
3
[Plug for external pilot]
2B
4A
n: Stations 2 3 4 5 6 7 8 9 10 11 12
L1 88.5 106 123.5 141 158.5 176 193.5 211 228.5 246 263.5
L2 78.5 96 113.5 131 148.5 166 183.5 201 218.5 236 253.5
L3 123 135.5 148 173 185.5 210.5 223 235.5 260.5 273 298
L4 112.5 125 137.5 162.5 175 200 212.5 225 250 262.5 287.5
L5 17.5 15 12.5 16 13.5 17.5 15 12.5 16 13.5 17.5
35
Plug-in Metal Base Series SY3000/5000/7000
Valve
Plug-in Type 50/Side Ported
U 02
SS5Y7-50(R)F 12 - Stations D - KC
C, N (D)
, KN
D side
L3
U side
Sub-plate
B
5.3 L4
(
JIS-X-5101
Applicable connector: D-sub MIL-C-24308 equivalent ) (DIN rail mounting hole pitch: 12.5)
(Pitch) (
Manual override
Push-turn locking slotted type:
)
DIN rail holding screw Press, then rotate it.
52 P = 19
Plug-in
M5 x 0.8 (External pilot) (For DIN rail mounting) 4(A) port side: Blue (For rubber seal)
16 24.1 (Light/surge voltage : Gray (For metal seal)
PE: Pilot EXH port DIN rail bracket mounting screw
(7.9) suppressor) 2(B) port side: Yellow
(For DIN rail mounting)
(DIN rail)
B A B A B A B A B A
(Connector entry
5.5
14 A 14 A 14 A 14 A 14 A
PE
5EA
upward direction)
116.7
23.8
28
35
102.1
Metal Base
133.2
92.1
84.6
24
1P
23.8
62.6
28.2
49.7
44.1
2 x M2.6 8
3EB
X
[For N or T thread]
NC
NC
Plug-in
18.1 4 x ø4.5
(5.4)
50RF12 - Stations U
D
(81.2)
78.3
84
2B 2B
67.2
44.5
9.4
3
32.4
4A 4A
[Plug for external pilot]
mounting)
14.3
4A
46.6 P = 19
One-touch fitting
[4(A), 2(B) port]
Applicable tube O.D.: ø8, ø5/16"
∗ The above drawing shows when P, : ø10, ø3/8"
E port entry is D.
Note) These figures show the “SS5Y7-50F2-05B-C10”.
Plug-in
Port size 02 One-touch fitting (Replaceable)
44.5
10.3
9.4
32.4
31.5
4A 4A
10.8 (Pitch)
(Pitch) 55.7 P = 19
46.6 P = 19 (11)
Plug Assembly Part No.
One-touch fitting
One-touch Fittings/
n: Stations 2 3 4 5 6 7 8 9 10 11 12
Manifold Options
L1 92 111 130 149 168 187 206 225 244 263 282
L2 82 101 120 139 158 177 196 215 234 253 272
L3 123 148 160.5 185.5 198 223 235.5 260.5 273 298 310.5
L4 112.5 137.5 150 175 187.5 212.5 225 250 262.5 287.5 300
L5 15.5 18.5 15.5 18.5 15 18 15 18 14.5 17.5 14.5
36
Series SY3000/5000/7000
P
U M5
SS5Y3-50(R) PG 1
PH 2 - Stations D - KC
C, N
, KN
(D) B
D side
L3
U side
J
5.3 L4
(DIN rail mounting hole pitch: 12.5) Manual override
Applicable connector:
26 pins MIL type with strain relief
(Conforming to MIL-C-83503) DIN rail holding screw 45.1
(Pitch)
P = 10.5
(Push-turn locking slotted type:
Press, then rotate it. )
(Light/surge 4(A) port side : Blue (For rubber seal)
(For DIN rail mounting) 14 24.1
M5 x 0.8 (External pilot) Triangle mark : Gray (For metal seal)
voltage
[Pilot EXH port] DIN rail bracket mounting screw (9.9) suppressor) 2(B) port side : Yellow
(For DIN rail mounting)
DIN rail
B A B A B A B A B A
(Connector entry
92.7
PE
14 A 14 A 14 A 14 A 14 A
5EA
89
16.8 17.2
15.9 16.2
79
5.5
upward direction)
64.4
35
56.9
21.8 16
1P
29.8
35
X
26.6
12 B 12 B 12 B 12 B 12 B
3EB
manual override)
50PH (10 pins)
(Slide locking
(80.6)
Triangle mark
68.3
62.6
Triangle mark
56.7
For PC wiring 2B 2B
7.1
32
22.6
4A 4A
7.5
5EA
5EA
PCW type
PE
PE
11.8
C4, C6: 6.6
1P
1P
X
3EB
3EB
2B 2B
50R PJ 12 - Stations UD
7.1
7.1
32
32
22.6
22.6
4A 4A
3
6.6 M5 x 0.8 (Pitch) [Plug for external pilot]
[4(A), 2(B) port] 48.4 P = 10.5 2B
(Pitch)
41.8 P = 10.5 One-touch fitting 4A
n: Stations 2 3 4 5 6 7 8 9 10 11 12
L1 71.5 82 92.5 103 113.5 124 134.5 145 155.5 166 176.5
L2 63.5 74 84.5 95 105.5 116 126.5 137 147.5 158 168.5
L3 98 110.5 123 135.5 148 160.5 160.5 173 185.5 198 210.5
L4 87.5 100 112.5 125 137.5 150 150 162.5 175 187.5 200
L5 13.5 14.5 15.5 16.5 17.5 18.5 13 14 15 16 17
37
Plug-in Metal Base Series SY3000/5000/7000
Valve
Plug-in Type 50/Side Ported
P
U
PH 2 - Stations D -01(D)
SS5Y3-50(R) PG 1
Sub-plate
J B
D side U side
L3
Plug-in
26 pins MIL type with strain relief
(Conforming to MIL-C-83503)
(DIN rail mounting hole pitch: 12.5)
(Pitch) (
Push-turn locking slotted type:
Press, then rotate it. )
DIN rail holding screw 45.1 P = 12.5 4(A) port side : Blue (For rubber seal)
Triangle mark : Gray (For metal seal)
(For DIN rail mounting) 14 24.1 (Light/surge
M5 x 0.8 (External pilot) voltage 2(B) port side : Yellow
[Pilot EXH port] DIN rail bracket mounting screw (9.9) suppressor)
(For DIN rail mounting)
DIN rail
Metal Base
B A B A B A B A B A
92.7
14 A 14 A 14 A 14 A 14 A
89
5EA
PE
16.8 17.2
15.9 16.2
79
5.5
64.4
35
56.9
21.8 16
1P
29.8
35
X
26.6
12 B 12 B 12 B 12 B 12 B
Plug-in
3EB
8.6 4 x ø4.5 4 L2 8
(For mounting)
14.5 (L5) L1
22.1 (Connector entry
manual override)
[1(P), 5(EA), 3(EB) port]
(Slide locking
(80.6)
68.3
62.6
56.7
7.1
32
22.6
4A 4A
mounting)
7.5
50PJG (20 pins) 50PH (10 pins)
11.8
41.8 P = 12.5
1/8
Triangle mark
[4(A), 2(B) port]
For PC wiring Triangle mark
Plug-in
5EA
5EA
PCW type
PE
PE
1P
X
3EB
3EB
3
Applicable connector: Applicable connector: [Plug for external pilot]
2B
20 pins MIL type with strain relief 10 pins MIL type with strain relief
(Conforming to MIL-C-83503) (Conforming to MIL-C-83503) 4A
Plug Assembly Part No.
port entry is D.
n: Stations 2 3 4 5 6 7 8 9 10 11 12
L1 76 88.5 101 113.5 126 138.5 151 163.5 176 188.5 201
Manifold Options
38
Series SY3000/5000/7000
P
U 01
SS5Y5-50(R) PG 1
PH 2 - Stations D - KC
C, N
, KN
(D) B
D side
L3
U side
J
Applicable connector: 5.3 L4
Manual override
26 pins MIL type with strain relief (DIN rail mounting hole pitch: 12.5)
(Conforming to MIL-C-83503)
Triangle mark
DIN rail holding screw
(For DIN rail mounting) 50
(Pitch)
P = 16
(
Push-turn locking slotted type:
Press, then rotate it. )
4(A) port side : Blue (For rubber seal)
(Light/surge
M5 x 0.8 (External pilot) 16 24.1 : Gray (For metal seal)
DIN rail bracket mounting screw voltage
[Pilot EXH port] (9.9) suppressor) 2(B) port side : Yellow
(For DIN rail mounting)
DIN rail
B A B A B A B A B A
14 A 14 A 14 A 14 A 14 A
(Connector entry
PE
5EA
106.2
5.5
23.2
116.6
upward direction)
96.2
35
20
81.6
20
74.1
1P
24.6
20
52.2
43.8
40.2
8
3EB
30.2
X
12 B 12 B 12 B 12 B 12 B
12.3
L2
)
5
Replaceable: 8.5
18 4 x ø4.5
(L5) L1
28 (For mounting)
Fixed: 4.9
manual override)
50PJG (20 pins) 50PH (10 pins)
(Slide locking
(86.6)
Triangle mark
74.3
Triangle mark
68.6
62.7
2B 2B
For PC wiring
7.8
38
27.3
4A 4A
10
PE
(Pitch)
mounting)
5EA
5EA
P = 16
14.3
45.8
1P
1P
One-touch fitting
[4(A), 2(B) port]
3EB
3EB
: ø6, ø1/4"
: ø8, ø5/16"
Note 1) These figures show the “SS5Y5-50P2-05B-C8”.
Applicable connector: Applicable connector:
Note 2) Only connectors are different for 50PG, 50PH and 50J.
20 pins MIL type with strain relief 10 pins MIL type with strain relief
L1 to L5 dimensions are the same as 50P type.
(Conforming to MIL-C-83503) (Conforming to MIL-C-83503)
3
[Plug for external pilot]
2B
2B
2B 4A
9.8
38
7.8
27.3
38
4A
27.3
4A
n: Stations 2 3 4 5 6 7 8 9 10 11 12
L1 84 100 116 132 148 164 180 196 212 228 244
L2 74 90 106 122 138 154 170 186 202 218 234
L3 110.5 135.5 148 160.5 173 198 210.5 223 248 260.5 273
L4 100 125 137.5 150 162.5 187.5 200 212.5 237.5 250 262.5
L5 13.5 18 16 14.5 12.5 17 15.5 13.5 18 16.5 14.5
39
Plug-in Metal Base Series SY3000/5000/7000
Valve
Plug-in Type 50/Side Ported
P
U
PH 2 - Stations D -02(D)
SS5Y5-50(R) PG 1
D side U side
Sub-plate
J B L3
Applicable connector: 5.3 L4 Manual override
26 pins MIL type with strain relief (DIN rail mounting hole pitch: 12.5)
(Conforming to MIL-C-83503) DIN rail holding screw (
Push-turn locking slotted type:
)
Plug-in
(Pitch) Press, then rotate it.
Triangle mark (For DIN rail mounting) 50 P = 17.5 4(A) port side : Blue (For rubber seal)
M5 x 0.8 (External pilot) 16 24.1 (Light/surge : Gray (For metal seal)
DIN rail bracket mounting screw
voltage suppressor) 2(B) port side : Yellow
[Pilot EXH port] (For DIN rail mounting) (9.9)
DIN rail
B A B A B A B A B A
Metal Base
(Connector entry 14 A 14 A 14 A 14 A 14 A
PE
5EA
106.2
5.5
23.2
116.6
upward direction)
96.2
35
20
81.6
20
74.1
1P
24.6
20
52.2
43.8
40.2
3EB
8
30.2
X
12 B 12 B 12 B 12 B 12 B
Plug-in
12.3
5 L2
18
(L5) 4 x ø4.5
M5 x 0.8 (External pilot) L1
28 (For mounting)
manual override)
(Slide locking
Triangle mark
(86.6)
Triangle mark
74.3
For PC wiring
68.6
62.7
2B 2B
9.8
38
27.3
4A 4A
PE
5EA
5EA
mounting)
(Pitch)
[4(A), 2(B) port]
14.3
45.8 P = 17.5
1P
1P
3EB
3EB
X
Plug-in
Applicable connector: Applicable connector: L1 to L5 dimensions are the same as 50P type.
20 pins MIL type with strain relief 10 pins MIL type with strain relief
(Conforming to MIL-C-83503) (Conforming to MIL-C-83503)
4A
Plug Assembly Part No.
One-touch Fittings/
n: Stations 2 3 4 5 6 7 8 9 10 11 12
Manifold Options
L1 88.5 106 123.5 141 158.5 176 193.5 211 228.5 246 263.5
L2 78.5 96 113.5 131 148.5 166 183.5 201 218.5 236 253.5
L3 123 135.5 148 173 185.5 210.5 223 235.5 260.5 273 298
L4 112.5 125 137.5 162.5 175 200 212.5 225 250 262.5 287.5
L5 17.5 15 12.5 16 13.5 17.5 15 12.5 16 13.5 17.5
40
Series SY3000/5000/7000
P
U 02 D side U side
SS5Y7-50(R) PG 1
PH 2 - Stations D - KC
C, N
, KN
(D) B
L3
J 5.3 L4
Applicable connector: Manual override
(DIN rail mounting hole pitch: 12.5)
( )
26 pins MIL type with strain relief Push-turn locking slotted type:
(Conforming to MIL-C-83503) (Pitch)
DIN rail holding screw 52 P = 19 Press, then rotate it.
Triangle mark (For DIN rail mounting) 4(A) port side: Blue (For rubber seal)
16 24.1 (Light/surge voltage : Gray (For metal seal)
M5 x 0.8 (External pilot) DIN rail bracket mounting screw
(9.9) suppressor) 2(B) port side: Yellow
PE: Pilot EXH port (For DIN rail mounting)
(DIN rail)
B A B A B A B A B A
(Connector entry 14 A 14 A 14 A 14 A 14 A
PE
5EA
116.7
upward direction)
5.5
23.8
35
28
102.1
133.2
92.1
84.6
24
1P
23.8
62.6
28.2
49.7
44.1
8
3EB
X
32.1
12 B 12 B 12 B 12 B 12 B
NC
NC
4 x ø4.5
18.1
(5.4)
(For mounting) 5 L2
20.9
M5 x 0.8 (External pilot) (L5) L1
34.5
40.5 X: External pilot port
(Station 1) (Station n)
3/8 18
[1(P), 5(EA), 3(EB) port]
manual override)
(Slide locking
50PJG (20 pins) 50PH (10 pins)
(93.1)
78.3
84
For PC wiring Triangle mark Triangle mark
69.2
2B 2B
44.5
9.4
32.4
4A 4A
PE
PE
PCW type
5EA
5EA
mounting)
10
46.6 P = 19
14.3
1P
1P
One-touch fitting
[4(A), 2(B) port]
3EB
3EB
X
3
[Plug for external pilot]
2B 2B 2B
44.5
44.5
10.3
9.4
32.4
31.5
4A 4A 4A
n: Stations 2 3 4 5 6 7 8 9 10 11 12
L1 92 111 130 149 168 187 206 225 244 263 282
L2 82 101 120 139 158 177 196 215 234 253 272
L3 123 148 160.5 185.5 198 223 235.5 260.5 273 298 310.5
L4 112.5 137.5 150 175 187.5 212.5 225 250 262.5 287.5 300
L5 15.5 18.5 15.5 18.5 15 18 15 18 14.5 17.5 14.5
41
Plug-in Metal Base Series SY3000/5000/7000
Valve
Plug-in Type 51/Bottom Ported
M5, 01
SS5Y3-51F 12- Stations D- CKC, N, D side U side Manual override
KN
( )
Sub-plate
(Light/surge voltage suppressor) Push-turn locking slotted type:
Press, then rotate it.
(Pitch) 4(A) port side : Blue (For rubber seal)
2 x M2.6
45.1 P = 10.5 : Gray (For metal seal)
2 x 4-40 UNC
14 24.1 2(B) port side : Yellow
[For N or T thread]
Plug-in
(7.9)
4 x ø4.5
(For mounting)
B A B A B A B A B A
92.7
16
89
14 A 14 A 14 A 14 A 14 A
64.4
35
12 B 12 B 12 B 12 B 12 B
21.8
(Max. 3) L1
Metal Base
6.1 (Station 1) --- (Station n)
manual override)
(Slide locking
(68.7)
68.3
62.6
54.7
Panel fitting dimensions
Plug-in
32
(For 9 stations or more)
(4.1)
2 x ø4.5
(For 9 stations or more) (Pitch)
4
21.1
16.8
: ø4, ø5/32"
52.4
56.4
16
: ø6, ø1/4"
29.8
3EB 2B 2B
4 x M4 x 0.7
56.4
4 x ø4.5 4 4
1P
5EA 4A 4A
L3
16.8
32
32
Plug-in
)C6: 12.8
N7: 16.6
20.1
29.8
29.8
17
1P 1P 1P
: ø4, ø5/32"
One-touch Fittings/
: ø6, ø1/4"
Port Size 01
n: Stations 2 3 4 5 6 7 8 9 10 11 12
L1 76 88.5 101 113.5 126 138.5 151 163.5 176 188.5 201
L2 68 80.5 93 105.5 118 130.5 143 155.5 168 180.5 193
L3 — — — — — — — 77.8 84 90.3 96.5
42
Series SY3000/5000/7000
50
(Pitch)
P = 16
(
Push-turn locking slotted type:
Press, then rotate it. )
2 x M2.6 4(A) port side : Blue (For rubber seal)
16 24.1 : Gray (For metal seal)
2 x 4-40 UNC
2(B) port side : Yellow
[For N or T thread] (7.9)
4 x ø4.5
(For mounting)
B A B A B A B A B A
106.2
14 A 14 A 14 A 14 A 14 A
116.6
81.6
30.2 20
52.2
12 B 12 B 12 B 12 B 12 B
(Max. 3) L1
manual override)
(Slide locking
(74.7)
74.3
68.6
60.7
38
Panel fitting dimensions
(4.9)
(Pitch)
2 x ø4.5 50 P = 16
2 x M4 x 0.7
25.2
40.2
3EB 2B 2B
20
: ø8, ø5/16"
20 20
4 x M4 x 0.7
71.6
1P
4 x ø4.5
5EA 4A 4A
5 5
Fitting dimensions for panel mounting
L3 1/4
C4, C6 : 14.8
: 17.2
Port size 01 Port size 02 One-touch fitting (Replaceable) Note) These figures show the “SS5Y5-
51F2-05D-C8”.
38
38
38
(15.5)
40.2
40.2
1P 1P 1P
17.5
14.8
14.5
Port Size 02
n: Stations 2 3 4 5 6 7 8 9 10 11 12
L1 88.5 106 123.5 141 158.5 176 193.5 211 228.5 246 263.5
L2 78.5 96 113.5 131 148.5 166 183.5 201 218.5 236 253.5
L3 — — — — — — — 100.5 109.3 118 126.8
43
Plug-in Metal Base Series SY3000/5000/7000
Valve
Plug-in Type 51/Bottom Ported
02
SS5Y7-51(R)F 12 - Stations D- CKC, N,
KN
(D) D side U side
Sub-plate
Manual override
(Light/surge voltage suppressor)
(
Push-turn locking slotted type:
Press, then rotate it. )
Applicable connector: D-sub ( JIS-X-5101
MIL-C-24308 )
equivalent 52
(Pitch)
P = 19 4(A) port side: Blue (For rubber seal)
Plug-in
16 24.1 : Gray (For metal seal)
(23.9) 2(B) port side: Yellow
4 x ø4.5
B A B A B A B A B A
(For mounting) 14 A 14 A 14 A 14 A 14 A
116.7
133.2
92.1
84.6
32.1 24
62.6
(Connector entry upward direction)
Metal Base
12 B 12 B 12 B 12 B 12 B
2 x M2.6
NC
NC
2 x 4-40 UNC
[For N or T thread]
Plug-in
manual override)
(Slide locking
(81.2)
78.3
84
67.2
44.5
22 33.1
Port size 02 One-touch fitting (Replaceable) dimensions for details.
46.1
3EB 2B 2B
23 23
81.1
1P
(For ø12)
5EA 4A 4A
(29.5)
One-touch fitting
[4(A), 2(B) port]
L3 Applicable tube O.D. C8 : ø8
C10: ø10
5 L2
Plug-in
N9 : ø5/16"
L1 N11: ø3/8"
(17.6)
: ø12
24 27.1
One-touch Fittings/
3EB 2B 3EB 2B
81.1
72.1
1P 1P
4 x M4 x 0.7
22.6
n: Stations 2 3 4 5 6 7 8 9 10 11 12
L1 92 111 130 149 168 187 206 225 244 263 282
L2 82 101 120 139 158 177 196 215 234 253 272
L3 — — — — — — — 107.5 117 126.5 136
44
Series SY3000/5000/7000
92.7
16
89
For PC wiring mark mark
14 A 14 A 14 A 14 A 14 A
64.4
35
12 B 12 B 12 B 12 B 12 B
21.8
(Connector entry
PCW type
upward direction)
(Max. 3) L1
(Station 1) --- (Station n)
18
manual override)
Applicable connector: Applicable connector:
(Slide locking
20 pins MIL type with strain relief 10 pins MIL type with strain relief
(80.6)
68.3
(Conforming to MIL-C-83503) (Conforming to MIL-C-83503)
62.6
56.7
32
Panel fitting dimensions
(4.1)
(For 9 stations or more)
(Pitch)
46.4 P = 10.5 One-touch fitting
2 x ø4.5 23.6 [4(A), 2(B) port]
4
21.1
(For 9 stations or more)
16.8
4 x ø4.5
29.8
3EB 2B 2B
52.4
56.4
16
56.4
1P
4 x M4 x 0.7 5EA 4A 4A
4 x ø4.5
16.8
Port size M5 Port size 01 One-touch fitting (Replaceable) Note) These figures show the “SS5Y3-
51P2-05D-C6”.
32
32
32
21.1
20.1
29.8
29.8
17
(
1P 1P 1P
One-touch fitting
M5 x 0.8 1/8
[4(A), 2(B) port]
[4(A), 2(B) port] [4(A), 2(B) port]
Applicable tube O.D.: ø2
: ø3.2, ø1/8"
: ø4, ø5/32"
: ø6, ø1/4"
Port Size M5, C, N, KC, KN
n: Stations 2 3 4 5 6 7 8 9 10 11 12
L1 71.5 82 92.5 103 113.5 124 134.5 145 155.5 166 176.5
L2 63.5 74 84.5 95 105.5 116 126.5 137 147.5 158 168.5
L3 — — — — — — — 68.5 73.8 79 84.3
Port Size 01
n: Stations 2 3 4 5 6 7 8 9 10 11 12
L1 76 88.5 101 113.5 126 138.5 151 163.5 176 188.5 201
L2 68 80.5 93 105.5 118 130.5 143 155.5 168 180.5 193
L3 — — — — — — — 77.8 84 90.3 96.5
45
Plug-in Metal Base Series SY3000/5000/7000
Valve
Plug-in Type 51/Bottom Ported
Sub-plate
KC, KN
J Applicable connector:
26 pins MIL type with strain relief
(Light/surge voltage suppressor)
(Pitch)
(
Push-turn locking slotted type:
Press, then rotate it. )
(Conforming to MIL-C-83503) 4(A) port side : Blue (For rubber seal)
50 P = 16
: Gray (For metal seal)
Triangle mark 16 24.1 2(B) port side : Yellow
Plug-in
(9.9) 4 x ø4.5
(For mounting)
B A B A B A B A B A
106.2
14 A 14 A 14 A 14 A 14 A
116.6
51PJG (20 pins) 51PH (10 pins)
81.6
30.2 20
52.2
For PC wiring Triangle mark Triangle mark 12 B 12 B 12 B 12 B 12 B
(Max. 3) L1
Metal Base
(Connector entry
PCW type
manual override)
(Slide locking
(86.6)
74.3
Plug-in
68.6
62.7
Applicable connector: Applicable connector:
38
20 pins MIL type with strain relief 10 pins MIL type with strain relief
(Conforming to MIL-C-83503) (Conforming to MIL-C-83503)
(Pitch)
(4.9)
50 P = 16
(For 9 stations or more) (For mounting) Applicable tube O.D.: ø4, ø5/32"
5
3EB 2B 2B
: ø8, ø5/16"
20 20
71.6
61.6
71.6
20
1P
4 x M4 x 0.7 5EA 4A 4A
C4, C6 : 14.8
: 17.2
[1(P), 5(EA), 3(EB) port]
L2 L3
L2
C8
Port size 01 Port size 02 One-touch fitting (Replaceable)
Note) These figures show the “SS5Y5-
51P2-05D-C8”.
Plug-in
38
38
38
40.2
40.2
1P 1P 1P
17.5
14.5
14.8
5EA 4A 5EA 4A
5EA 4A
: ø6, ø1/4"
: ø8, ø5/16"
46
Series SY3000/5000/7000
Plug-in Type 51/Bottom Ported
P 02
SS5Y7-51(R) PG 1
PH 2 - Stations D- C, N (D) D side U side
J KC, KN
Manual override
(Light/surge voltage suppressor)
(Pitch)
(Push-turn locking slotted type:
Press, then rotate it. )
52 P = 19 4(A) port side: Blue (For rubber seal)
Applicable connector: : Gray (For metal seal)
16 24.1
Triangle mark 26 pins MIL type with strain relief 2(B) port side: Yellow
(25.9)
(Conforming to MIL-C-83503)
4 x ø4.5
B A B A B A B A B A
(For mounting) 14 A 14 A 14 A 14 A 14 A
116.7
133.2
92.1
84.6
32.1 24
62.6
(Connector entry upward direction)
12 B 12 B 12 B 12 B 12 B
NC
NC
18 (Station 1) (Station n)
50PJG (20 pins) 51PH (10 pins)
Triangle mark
manual override)
Triangle mark
(Slide locking
For PC wiring
(93.1)
78.3
84
69.2
44.5
PCW type
(5.4)
4 x M4 x 0.7 thread depth 5
(For mounting) 3/8
(Pitch)
(Max. 3) 52 P = 19 [1(P), 5(EA), 3(EB) port]
3EB 2B 2B
23 23
81.1
1P
5EA 4A 4A
(For ø12)
(29.5)
One-touch fitting
[4(A), 2(B) port]
L3 Applicable tube O.D. C8 : ø8
C10: ø10
5 L2 N9 : ø5/16"
L1 N11: ø3/8"
(17.6)
24 27.1
32.8
22 33.1
3EB 2B 3EB 2B
81.1
72.1
1P 1P
4 x M4 x 0.7
22.6
5EA 4A 5EA 4A
5 5 4 x ø4.5
L3
L2
n: Stations 2 3 4 5 6 7 8 9 10 11 12
L1 92 111 130 149 168 187 206 225 244 263 282
L2 82 101 120 139 158 177 196 215 234 253 272
L3 — — — — — — — 107.5 117 126.5 136
47
48
One-touch Fittings/ Type 10, 11, 12 Type 50, 51, 52
Manifold Options Plug-in Connector Connecting Base Plug-in Metal Base Plug-in Sub-plate Valve
Plug Assembly Part No. Manifold Exploded View Manifold Exploded View
Plug-in Metal Base
Type 52
D-sub Connector Flat Ribbon Cable PC Wiring
Top Ported
Series SY3000/5000/7000
RoHS
How to Order Manifold
SS5Y 3 52 F 1 05 D
Series Type Connector type
3 SY3000 52 Top ported F: D-sub connector P: Flat ribbon cable PG: Flat ribbon cable
5 SY5000 52R Top ported, External pilot (25 pins) (26 pins) (20 pins)
7 SY7000
Wiring type
Nil All double wiring Note 1)
S All single wiring Note 2) Valve stations
Note 1) All double wiring: 2-position single, double, 3-position and 4-position
valves can be used on all manifold stations. F: D-sub connector (25 pins) P: Flat ribbon cable (26 pins) PG: Flat ribbon cable (20 pins)
Note 2) All single wiring: Available only for the manifold which has 2-position Symbol Stations Note Symbol Stations Note Symbol Stations Note
single for all stations. 02 2 stations All 02 2 stations All 02 2 stations All
Note that 2-position double, 3- or 4-position valves cannot be used.
Note 3) If a mix of single and double wiring is required, it is supplied as a double double double
special order. 12 12 stations wiring 12 12 stations wiring 09 9 stations wiring
02 2 stations All 02 2 stations All 02 2 stations All
How to Order Manifold Assembly single single single
12 12 stations wiring 12 12 stations wiring 12 12 stations wiring
Example (SS5Y3-52F2-) PH: Flat ribbon cable (10 pins) J: PC wiring (20 pins)
2-position double (24 VDC) Symbol Stations Note Symbol Stations Note
2-position single (24 VDC)
SY3130-5U1-C6 (3 sets) SY3230-5U1-C6 (1 set) 02 2 stations All 02 2 stations All
3-position closed double double
center (24 VDC) 04 4 stations wiring 08 8 stations wiring
SY3330-5U1-C6 (1 set) 02 2 stations 02 2 stations
All All
single single
08 8 stations wiring 12 12 stations wiring
∗ This also includes the number of blanking plate assembly.
Us
ide P, E port entry Thread type
on
s U U side Note) Nil Rc
ati
St D D side Note) 00F G
Manifold base 3 B Both sides 00N NPT
2
(5 stations) 1 00T NPTF
e Note) Plugs are mounted on the opposite
SS5Y3-52F2-05D sid
D side of the selected ports.
SS5Y3-52F2-05D ·········1 set (Type 52 5-station manifold base part no.) Mounting
∗SY3130-5U1-C6 ···········3 sets (2-position single part no.)
∗SY3230-5U1-C6 ···········1 set (2-position double part no.) Nil Direct mounting
∗SY3330-5U1-C6 ···········1 set (3-position closed center part no.) D DIN rail mounting (With DIN rail)
The asterisk denotes the symbol for assembly.
D0 DIN rail mounting (Without DIN rail)
Prefix it to the part numbers of the valve etc. D3 For 3 stations
Specify a longer rail than
• The valve arrangement is numbered as the 1st station from the D side. the standard length.
D12 For 12 stations
• Under the manifold part number, state the valves to be mounted in order
from the 1st station as shown in the figure above. If the arrangement Note) Refer to page 247 for the fixation of DIN rail
becomes complicated, specify on a manifold specification sheet. mounting type manifold.
49
Plug-in Metal Base Series SY3000/5000/7000
Valve
How to Order Valves (With mounting screw) Refer to page 3 for valve specifications.
SY 3 1 3 0 5 1 C6
Sub-plate
Plug-in
Top ported
Metal Base
when a valve is continuously energized for long 02 1/4 SY7000
Type of actuation periods of time.
1 Single ∗ Be careful of the energizing time when the One-touch fitting (Metric)
2-position power saving circuit is selected. Refer to page Symbol A, B port SY3000 SY5000 SY7000
2 Double
3 Closed center 244 for details. C2 ø2 — —
Plug-in
4 3-position Exhaust center C3 ø3.2 — —
5 Pressure center Rated voltage C4 ø4 —
A∗ 4-position N.C./N.C. 5 24 VDC
C6 ø6
B∗ dual N.O./N.O. 6 12 VDC
C8 ø8 —
C∗ 3-port N.C./N.O. C10 ø10 — —
C12 ø12 — —
Plug-in
∗ Only rubber seal type
Non-locking Push-turn
∗ Back pressure check valve is not available for the
3-position type and the SY7000. push type locking Nil Round head combination screw
slotted B Hexagon socket head cap screw
Protective class
class III (Mark: )
50
Series SY3000/5000/7000
Dimensions: Series SY3000 Metal Base D-sub Connector, Flat Ribbon Cable
F
P 1 U D side U side
SS5Y3-52(R) PG - Stations D -(D) L3
PH 2 B
J 5.3 L4
(DIN rail mounting hole pitch: 12.5)
Applicable connector: D-sub ( JIS-X-5101
MIL-C-24308 )
equivalent (Pitch) Manual override
68.3
DIN rail holding screw
(For DIN rail mounting)
14
45.1
24.1
P = 10.5
(Push-turn locking slotted type:
Press, then rotate it. )
(Light/surge 4(A) port side : Blue (For rubber seal)
(Slide locking manual override) (7.9) voltage : Gray (For metal seal)
M5 x 0.8 (External pilot) DIN rail bracket mounting screw suppressor) 2(B) port side : Yellow
[Pilot EXH port] (For DIN rail mounting)
DIN rail
5.5
(Connector entry B A B A B A B A B A
upward direction)
92.7
4A 4A 4A 4A 4A
5EA
89
PE
16.8 17.2
79
15.9 16.2
64.4
56.9
16
1P
2 x M2.6
11
32.1
35
29.8
35
X
26.6
2 x 4-40 UNC
21.8
2B 2B 2B 2B 2B
3EB
[For N or T thread]
8.6 4 x ø4.5
8 One-touch fitting
14.5 (For mounting) 4 L2
M5 x 0.8 (External pilot) [4(A), 2(B) port]
22.1 (L5) L1 Applicable tube O.D.: ø2
[External pilot port]
28 : ø3.2, ø1/8"
1/8 M5 x 0.8
: ø4, ø5/32"
[1(P), 5(EA), 3(EB) port] [4(A), 2(B) port] : ø6, ø1/4"
(Station 1) --- (Station n)
6.1
F
52R PJ 12 - Stations U
D
)C6: 76.8
N7: 80.6
(68.7)
62.6
54.7
(
[Plug for external pilot]
32
mounting)
11.8
∗ The above drawing shows when P, E
port entry is D.
B A B A B A
4A 4A 4A
5EA
5EA
5EA
PE
PE
PE
PCW type
1P
1P
1P
X
2B 2B 2B
3EB
3EB
3EB
n: Stations 2 3 4 5 6 7 8 9 10 11 12
L1 71.5 82 92.5 103 113.5 124 134.5 145 155.5 166 176.5
L2 63.5 74 84.5 95 105.5 116 126.5 137 147.5 158 168.5
L3 98 110.5 123 135.5 148 160.5 160.5 173 185.5 198 210.5
L4 87.5 100 112.5 125 137.5 150 150 162.5 175 187.5 200
L5 13.5 14.5 15.5 16.5 17.5 18.5 13 14 15 16 17
51
Plug-in Metal Base Series SY3000/5000/7000
Valve
Plug-in Type 52/Top Ported
Dimensions: Series SY5000 Metal Base D-sub Connector, Flat Ribbon Cable
F
P U
SS5Y5-52(R) PG D -(D)
1 Stations
- D side U side
Sub-plate
PH 2 B
L3 Manual override
J L4
( ) ( )
JIS-X-5101 5.3 Push-turn locking slotted type:
Applicable connector: D-sub MIL-C-24308 equivalent (DIN rail mounting hole pitch: 12.5) Press, then rotate it.
(Pitch) 4(A) port side : Blue (For rubber seal)
74.3
P = 16 (Light/surge
Plug-in
DIN rail holding screw 50 : Gray (For metal seal)
(Slide locking manual override) voltage
68.6 (For DIN rail mounting) 16 24.1 2(B) port side : Yellow
M5 x 0.8 (External pilot) suppressor)
DIN rail bracket mounting screw (7.9)
[Pilot EXH port]
01 : 16.2
C : 14.5
(For DIN rail mounting)
DIN rail
(Connector entry B A B A B A B A B A
4A 4A 4A 4A 4A
PE
upward direction)
5EA
106.2
5.5
23.2
116.6
96.2
35
20
81.6
Metal Base
20
74.1
1P
24.6
20
52.2
43.8
2 x M2.6
40.2
40.2
8
3EB
30.2
X
2B 2B 2B 2B 2B
2 x 4-40 UNC
[For N or T thread]
12.3
Plug-in
1/8
M5 x 0.8 (External pilot) 4 x ø4.5 One-touch fitting
18 [4(A), 2(B) port]
[External pilot port] (For mounting) [4(A), 2(B) port]
28 5 L2
1/4 Applicable tube O.D.: ø4, ø5/32"
34 (L5) L1 : ø6, ø1/4"
[1(P), 5(EA), 3(EB) port]
: ø8, ø5/16"
(86.7)
(74.7)
72.3
60.7
B A
4A
PE
5EA
38
mounting)
14.3
Applicable connector: Note) These figures show the “SS5Y5-52F2-05B”.
26 pins MIL type with strain relief
(Conforming to MIL-C-83503)
Plug-in
F
52PJG (20 pins) 52PH (10 pins) 52R PJ 12 - Stations UD
For PC wiring
16 (9.9) Triangle mark 16 (9.9)
Triangle mark
PE
5EA
5EA
PCW type
1P
1P
3EB
3EB
X
2B 2B
∗ The above drawing shows when P, E
Plug Assembly Part No.
port entry is D.
One-touch Fittings/
n: Stations 2 3 4 5 6 7 8 9 10 11 12
Manifold Options
L1 84 100 116 132 148 164 180 196 212 228 244
L2 74 90 106 122 138 154 170 186 202 218 234
L3 110.5 135.5 148 160.5 173 198 210.5 223 248 260.5 273
L4 100 125 137.5 150 162.5 187.5 200 212.5 237.5 250 262.5
L5 13.5 18 16 14.5 12.5 17 15.5 13.5 18 16.5 14.5
52
Series SY3000/5000/7000
Dimensions: Series SY7000 Metal Base D-sub Connector, Flat Ribbon Cable
F
1 P U
SS5Y7-52(R) PG
PH 2
- Stations D -(D) D side
L3 U side
B L4
J JIS-X-5101 5.3
(
Applicable connector: D-sub MIL-C-24308 equivalent ) (DIN rail mounting hole pitch: 12.5)
Manual override
84
DIN rail holding screw 52
P = 19
(Pitch)
(
Push-turn locking slotted type:
Press, then rotate it. )
(Slide locking manual override) 16 24.1 4(A) port side : Blue (For rubber seal)
(For DIN rail mounting) (Light/surge voltage
M5 x 0.8 (External pilot) 78.3 suppressor) : Gray (For metal seal)
(7.9) 2(B) port side : Yellow
PE: Pilot EXH port
DIN rail bracket mounting screw
(For DIN rail mounting)
(DIN rail) B A B A B A B A B A
5.5
4A 4A 4A 4A 4A
PE
5EA
116.7
23.8
28
35
102.1
133.2
92.1
84.6
24
1P
23.8
62.6
28.2
49.7
45.6
44.1
22.6
8
3EB
X
2 x M2.6
32.1
2B 2B 2B 2B 2B
2 x 4-40 UNC
NC
NC
[For N or T thread]
18.1 4 x ø4.5 1/4
20.9 (For mounting) [1 (A), 2 (B) port]
One-touch fitting
34.5 M5 x 0.8 (External pilot) 5 L2
[4(A), 2(B) port]
40.5 X: External pilot port (L5) L1 Applicable tube O.D. : ø6, ø1/4"
3/8
(Connector entry upward direction) : ø8, ø5/16"
[1 (P), 5 (EA), 3 (EB) port] : ø10, ø3/8"
(Station 1) (Station n) : ø12
52P (26 pins)
Triangle mark 16 (9.9) 6.1
4A
PE
5EA
67.2
44.5
1P
3EB
X
2B
mounting)
14.3
Applicable connector:
26 pins MIL type with strain relief Note) These figures show the “SS5Y7-52F2-05B”.
(Conforming to MIL-C-83503)
F
52PJG (20 pins) 52PH (10 pins) 52R PJ 12 - Stations UD
For PC wiring Triangle mark 16 (9.9) Triangle mark 16 (9.9)
3
[Plug for external pilot]
B A B A
4A 4A
PE
PE
PCW type
5EA
5EA
1P
1P
3EB
3EB
X
2B 2B
n: Stations 2 3 4 5 6 7 8 9 10 11 12
L1 92 111 130 149 168 187 206 225 244 263 282
L2 82 101 120 139 158 177 196 215 234 253 272
L3 123 148 160.5 185.5 198 223 235.5 260.5 273 298 310.5
L4 112.5 137.5 150 175 187.5 212.5 225 250 262.5 287.5 300
L5 15.5 18.5 15.5 18.5 15 18 15 18 14.5 17.5 14.5
53
Plug-in Metal Base Series SY3000/5000/7000
Valve
Electrical Wiring Specifications Cable Assembly
015
D-sub connector
AXT100-DS25- 030 (N) [IP40 compliant]
Sub-plate
050 Lead wire color for
Nil: Metric size
N: Inch size D-sub connector
1
cable assembly by
14 2 terminal number
15 Cable
Plug-in
3 Lead Dot
16 4 0.3 mm2 x 25 cores Terminal wire
17 no. marking
5 O.D. ø1.4 color
18 6 1 Black None
19 Approx. ø10
7 2 Brown None
20 8
21 9 3 Red None
22 Connector terminal no. Seal (Length)
10 015 4 Orange None
23 11
24 5 Yellow None
12
L
25 13 Molded cover 6 Pink None
Metal Base
7 Blue None
2 x M2.6 x 0.45
44
or 2 x 4-40 UNC 8 Purple White
Connector JBZ-25S-3 9 Gray Black
<All single wiring> <All double wiring> made by J.S.T. Mfg. 10 White Black
8
Terminal no. Terminal no. Polarity Co., Ltd.
11 White Red
Plug-in
(2.4)
SOL.a SOL.a 55 12 Yellow Red
Station 1 1 1 (–) (+) Socket side
SOL.a Station 1 SOL.b 13 Orange Red
Station 2 14 14 (–) (+) 14 25
SOL.a SOL.a 14 Yellow Black
Station 3 2 2 (–) (+) Terminal no.
Station 2
16
SOL.a SOL.b 15 Pink Black
Station 4 15 15 (–) (+)
SOL.a SOL.a 16 Blue White
Station 5 3 3 (–) (+) 1 13
Plug-in
12 SOL.a
12 (–) (+)
Station 12 SOL.b Item Property
25 25 (–) (+) • Fujitsu, Ltd.
Conductor resistance • Japan Aviation Electronics Industry, Ltd.
Ω/km, 20°C 65 or less
• J.S.T. Mfg. Co., Ltd.
54
Series SY3000/5000/7000
Electrical Wiring Specifications Cable Assembly
10 1
Flat ribbon cable connector AXT100-FC 20 - 2
26 3
26 25
24 23
6 Terminal no. 28AWG
Red
22 21
20 19
1
18 17
16 15
14 13
12 11 Connector terminal no.
10 9
26
25
8 7
Triangle mark indicator position (15.6)
6 5
4 3 L
2 1
Flat ribbon cable connector assembly
Cable Assembly part no.
P: Flat ribbon cable (26 pins) length (L) 26 pins 20 pins 10 pins
<All single wiring> <All double wiring> 1.5 m AXT100-FC26-1 AXT100-FC20-1 AXT100-FC10-1
Terminal no. Terminal no. Polarity 3m AXT100-FC26-2 AXT100-FC20-2 AXT100-FC10-2
SOL.a 1 SOL.a (–) (+) AXT100-FC26-3 AXT100-FC20-3 AXT100-FC10-3
Station 1 1 5m
Station 2
SOL.a 2 Station 1 SOL.b 2 (–) (+) ∗ When using a standard commercial connector, use a 26-pin, 20-pin or 10-pin
SOL.a 3 SOL.a 3 (–) (+)
Station 3 type connector conforming to MIL-C-83503 with strain relief.
Station 4
SOL.a 4 Station 2 SOL.b 4 (–) (+) ∗ Cannot be used for movable wiring.
Station 5 SOL.a 5 SOL.a 5 (–) (+) ∗ Lengths other than the above are also available. Please contact SMC for
Station 6
SOL.a 6 Station 3 SOL.b 6 (–) (+) details.
Station 7 SOL.a 7 SOL.a 7 (–) (+)
Station 8 SOL.a 8 Station 4 SOL.b 8 (–) (+) Connector Manufacturers’ Example
Station 9 SOL.a 9 SOL.a 9 (–) (+)
Station 10 SOL.a 10 Station 5 SOL.b 10 (–) (+) • Hirose Electric Co., Ltd. • Japan Aviation Electronics Industry, Ltd.
Station 11 SOL.a 11 SOL.a 11 (–) (+) • Sumitomo 3M Limited • J.S.T. Mfg. Co., Ltd.
Station 12 SOL.a 12 Station 6 SOL.b 12 (–) (+) • Fujitsu, Ltd. • Oki Electric Cable Co., Ltd.
13 SOL.a 13 (–) (+)
Station 7 SOL.b 14
14 (–) (+)
15 SOL.a 15 (–) (+) PH: Flat ribbon cable (10 pins)
Station 8 SOL.b 16
16 (–) (+) <All single wiring> <All double wiring>
17 SOL.a 17 (–) (+)
Station 9 SOL.b 18 Terminal no. Terminal no. Polarity
18 (–) (+) SOL.a SOL.a
19 SOL.a 19 (–) (+) Station 1 1 1 (–) (+)
Station 10 SOL.a Station 1 SOL.b
SOL.b 20 (–) (+) Station 2 2 2 (–) (+)
20 SOL.a SOL.a
SOL.a 21 (–) (+) Station 3 3 3 (–) (+)
21 SOL.a Station 2 SOL.b
Station 11 SOL.b 22 Station 4 4 4 (–) (+)
22 (–) (+) SOL.a SOL.a
23 SOL.a 23 (–) (+) Station 5 5 5 (–) (+)
Station 12 SOL.a Station 3 SOL.b
24 SOL.b 24 (–) (+) Station 6 6 6 (–) (+)
Station 7 SOL.a SOL.a 7 (–) (+)
COM. COM. 7
25 25 (+) (–) SOL.a Station 4 SOL.b
COM. 26 COM. Station 8 8 8 (–) (+)
26 (+) (–) COM. COM.
9 9 (+) (–)
Positive Negative COM. 10 COM.
10 (+) (–)
common common
Positive Negative
common common
PG: Flat ribbon cable (20 pins)
<All single wiring> <All double wiring> J: Flat ribbon cable (20 pins) PC wiring
Terminal no. Terminal no. Polarity
SOL.a SOL.a <All single wiring> <All double wiring>
Station 1 1 1 (–) (+)
SOL.a Station 1 SOL.b Terminal no. Terminal no. Polarity
Station 2 2 2 (–) (+)
SOL.a SOL.a (–) (+) SOL.a 20 SOL.a 20 (–) (+)
Station 3 3 3 Station 1
SOL.a Station 2 SOL.b SOL.a Station 1 SOL.b 18
Station 4 4 4 (–) (+) Station 2 18 (–) (+)
Station 5 SOL.a SOL.a 5 (–) (+) SOL.a SOL.a 16 (–) (+)
5 Station 3 16
SOL.a Station 3 SOL.b SOL.a Station 2 SOL.b 14
Station 6 6 6 (–) (+) Station 4 14 (–) (+)
Station 7 SOL.a SOL.a 7 (–) (+) Station 5 SOL.a SOL.a 12
7 12 (–) (+)
SOL.a Station 4 SOL.b SOL.a Station 3 SOL.b 10
Station 8 8 8 (–) (+) Station 6 10 (–) (+)
Station 9 SOL.a SOL.a 9 (–) (+) Station 7 SOL.a SOL.a
9 8 8 (–) (+)
SOL.a Station 5 SOL.b 10 SOL.a Station 4 SOL.b
Station 10 10 (–) (+) Station 8 6 6 (–) (+)
Station 11 SOL.a SOL.a 11 (–) (+) Station 9 SOL.a SOL.a
11 19 19 (–) (+)
SOL.a Station 6 SOL.b 12 SOL.a 17 Station 5 SOL.b
Station 12 12 (–) (+) Station 10 17 (–) (+)
SOL.a 13 (–) (+) Station 11 SOL.a 15 SOL.a
13 15 (–) (+)
Station 7 SOL.b 14 SOL.a 13 Station 6 SOL.b
14 (–) (+) Station 12 13 (–) (+)
SOL.a 15 (–) (+) 11 SOL.a
15 11 (–) (+)
Station 8 SOL.b 16 Station 7 SOL.b
16 (–) (+) 9 9 (–) (+)
SOL.a 17 (–) (+) 7 SOL.a
17 7 (–) (+)
Station 9 SOL.b 18 Station 8 SOL.b
18 (–) (+) 5 5 (–) (+)
COM. 19 COM. 4 4
19 (+) (–)
COM. 20 COM. 3 3
20 (+) (–)
COM. 2 COM. 2 (+) (–)
Positive Negative
common common COM. 1 COM. 1 (+) (–)
Positive Negative
Note) When using a valve with no polarity, either positive common or negative
common common
common can be used.
55
56
One-touch Fittings/ Type 10, 11, 12 Type 50, 51, 52
Manifold Options Plug-in Connector Connecting Base Plug-in Metal Base Plug-in Sub-plate Valve
Plug Assembly Part No. Manifold Exploded View Manifold Exploded View
Type 50
Side Ported Plug-in Metal Base EX510
Series SY3000/5000/7000
Type 51
Bottom Ported
SS5Y 3 50 S5 05 D C6
Series Type Valve stations
3 SY3000 50 Side ported Symbol Stations Note Symbol Stations Note
5 SY5000 51 Bottom ported 02 2 stations 02 2 stations
All double All single
7 SY7000 50R Side ported, External pilot
wiring wiring
∗ External pilot is not available for 08 8 stations 12 12 stations
SI unit output polarity the bottom ported type. ∗ This also includes the number of blanking plate assembly.
Nil Positive common
N Negative common
P, E port entry
U U side Note 1) Note 1) Plugs are mounted on the opposite
side of the selected ports.
Wiring type D D side Note 1) Note 2)
Note 2) Only D side is available for Type 51
B Both sides (Bottom ported).
Nil All double wiring Note 1)
S All single wiring Note 2) A, B port size
Note 1) All double wiring: 2-position single, double, 3-position and 4-position Thread piping
valves can be used on all manifold stations.
Note 2) All single wiring: Available only for the manifold which has 2-position
Symbol A, B port SY3000 SY5000 SY7000
single for all stations. M5 M5 x 0.8 — —
Note that 2-position double, 3- or 4-position valves cannot be used. 01 1/8 —
Note 3) If a mix of single and double wiring is required, it is supplied as a 02 1/4 —
special order. One-touch fitting (Metric)
Symbol A, B port SY3000 SY5000 SY7000
C2 ø2 — —
C3 ø3.2 — —
How to Order Manifold Assembly C4 ø4 —
Fixed
C6 ø6 —
Example (SS5Y3-50S5-) C8 ø8 —
2-position double (24 VDC)
2-position single (24 VDC) C10 ø10 — —
SY3100-5U1 (3 sets) SY3200-5U1 (1 set)
3-position closed KC2 ø2 — — Type 50 Type 51
center (24 VDC) (Side ported) (Bottom ported)
KC3 ø3.2 — —
SY3300-5U1 (1 set)
KC4 ø4 —
Replaceable
KC6 ø6
KC8 ø8 —
KC10 ø10 — —
KC12 ø12 — —
ide M∗ Mixed sizes
Us
P, E port size (Thread piping) 1/8 1/4 3/8
s
n
tio
ta
3
Manifold base 2 Symbol A, B port SY3000 SY5000 SY7000
1
(5 stations) ide N1 ø1/8" — —
SS5Y3-50S5-05D-C6 Ds
N3 ø5/32" —
Fixed
• The valve arrangement is numbered as the 1st station from the D side.
KN7 ø1/4"
• Under the manifold part number, state the valves to be mounted in order from
the 1st station as shown in the figure above. If the arrangement becomes KN9 ø5/16" —
complicated, specify on a manifold specification sheet. KN11 ø3/8" — —
Note) When mixing top ported configurations, select from page 68. M∗ Mixed sizes
In this case, use caution as there is also output on the A and B port on base side.
P, E port size (Thread piping) 1/8 1/4 3/8
Specify on a manifold specification sheet if plugs are required on the A and B
port on base side. ∗ When ports are mixed sizes, indicate the piping specifications on the manifold specification sheet.
57
Plug-in Metal Base Series SY3000/5000/7000
Valve
Thread type Mounting
Sub-plate
Nil Rc Nil Direct mounting
F G DIN rail mounting
D
N NPT (With DIN rail) For details about the EX510 Gateway-type
T NPTF
Plug-in
DIN rail mounting Serial Transmission System, refer to the
D0 (Without DIN rail) WEB catalog or the Best Pneumatics No. 1
D3 For 3 stations and the Operation Manual. Please download
Specify a longer rail than the Operation Manual via SMC website,
the standard length. http://www.smcworld.com
D12 For 12 stations
Note 1) Only direct mounting is available for Type
51 (Bottom ported).
Note 2) Refer to page 247 for the fixation of DIN
rail mounting type manifold.
Metal Base
How to Order Valves (With mounting screw) Refer to page 3 for valve specifications.
SY 3 1 0 0 5 1
Plug-in
Manual override
Nil: D:
Non-locking Push-turn
Base mounted
Plug-in
4-position dual 3-port valve. Nil Round head combination screw
B Hexagon socket head cap screw
Rated voltage
Seal type 5 K
Round head combination screw
common
Z
One-touch Fittings/
Protective class
class III (Mark: )
58
Series SY3000/5000/7000
U M5
SS5Y3-50(R)S5- Stations D - KC
C, N (D)
, KN
D side
L3
U side
B
5.3 L4
(DIN rail mounting hole pitch: 12.5) Manual override
B A B A B A B A B A
92.7
14 A 14 A 14 A 14 A 14 A
5EA
89
PE
16.8 17.2
79
15.9 16.2
5.5
64.4
35
56.9
21.8 16
1P
29.8
26.6
12 B 12 B 12 B 12 B 12 B
3EB
(For mounting)
Replaceable: 7.7
14.5 4 L2
22.1 (L5) L1
Fixed: 4.1
manual override)
(Slide locking
50RS5- Stations UD
68.3
65.6
62.6
2B 2B
7.1
32
22.6
4A 4A
3
[Plug for external pilot]
mounting)
7.5
C4, C6: 6.6
11.8
4A [4(A), 2(B) port]
Applicable tube O.D.: ø2
C2, C3: 42.4 (Pitch) : ø3.2, ø1/8"
C4, C6: 41.8 P = 10.5 : ø4, ø5/32"
∗ The above drawing shows when P, E : ø6, ø1/4"
port entry is D.
Note) These figures show the “SS5Y3-50S5-05B-C6”.
2B 2B
7.1
32
32
7.1
22.6
22.6
4A 4A
One-touch fitting
M5 x 0.8 [4(A), 2(B) port]
[4(A), 2(B) port] Applicable tube O.D.: ø2
6.6 (Pitch)
(Pitch) : ø3.2, ø1/8"
41.8 P = 10.5 : ø4, ø5/32"
48.4 P = 10.5
: ø6, ø1/4"
n: Stations 2 3 4 5 6 7 8 9 10 11 12
L1 71.5 82 92.5 103 113.5 124 134.5 145 155.5 166 176.5
L2 63.5 74 84.5 95 105.5 116 126.5 137 147.5 158 168.5
L3 98 110.5 123 135.5 148 160.5 160.5 173 185.5 198 210.5
L4 87.5 100 112.5 125 137.5 150 150 162.5 175 187.5 200
L5 13.5 14.5 15.5 16.5 17.5 18.5 13 14 15 16 17
59
Plug-in Metal Base Series SY3000/5000/7000
Valve
Plug-in Type 50/Side Ported
U
SS5Y3-50(R)S5- Stations D -01(D)
Sub-plate
B
D side U side
L3
5.3 L4
(DIN rail mounting hole pitch: 12.5) Manual override
Plug-in
M5 x 0.8 (External pilot)
[Pilot EXH port]
DIN rail holding screw 45.1
(Pitch)
P = 12.5 ( Push-turn locking slotted type:
Press, then rotate it. )
18.5 19.6 4(A) port side : Blue (For rubber seal)
(For DIN rail mounting) (Light/surge voltage : Gray (For metal seal)
suppressor) 2(B) port side : Yellow
DIN rail bracket mounting screw
(For DIN rail mounting)
DIN rail
Metal Base
B A B A B A B A B A
92.7
14 A 14 A 14 A 14 A 14 A
5EA
89
PE
16.8 17.2
79
15.9 16.2
5.5
64.4
35
56.9
16
1P
29.8
26.6
12 B 12 B 12 B 12 B 12 B
21.8
3EB
Plug-in
8.6 4 x ø4.5 SI unit 8
14.5 (For mounting) 4 L2
22.1 M5 x 0.8 (External pilot) (L5) L1
28 [External pilot port]
manual override)
(Slide locking
68.3
65.6
62.6
50RS5- Stations UD 2B 2B
7.1
mounting)
2B 41.8 P = 12.5 [4(A), 2(B) port] 7.5
4A
11.8
Plug-in
∗ The above drawing shows when P, E
port entry is D. Note) These figures show the “SS5Y3-50S5-05B-01”.
n: Stations 2 3 4 5 6 7 8 9 10 11 12
L1 76 88.5 101 113.5 126 138.5 151 163.5 176 188.5 201
L2 68 80.5 93 105.5 118 130.5 143 155.5 168 180.5 193
Manifold Options
L3 110.5 123 135.5 148 160.5 173 185.5 198 210.5 223 235.5
L4 100 112.5 125 137.5 150 162.5 175 187.5 200 212.5 225
L5 17.5 17.5 17.5 17.5 17.5 17.5 17.5 17.5 17.5 17.5 17.5
60
Series SY3000/5000/7000
U 01
SS5Y5-50(R)S5- Stations D - KC
C, N (D)
, KN D side U side
B
L3
M5 x 0.8 (External pilot) 5.3 L4
Manual override
[Pilot EXH port] (DIN rail mounting hole pitch: 12.5)
DIN rail holding screw
50
(Pitch)
P = 16
(
Push-turn locking slotted type:
Press, then rotate it. )
(For DIN rail mounting) 4(A) port side : Blue (For rubber seal)
DIN rail bracket mounting screw 20.5 19.6 (Light/surge voltage : Gray (For metal seal)
(For DIN rail mounting) suppressor) 2(B) port side : Yellow
DIN rail
B A B A B A B A B A
14 A 14 A 14 A 14 A 14 A
PE
5EA
106.2
5.5
23.2
116.6
35
96.2
20
81.6
20
74.1
1P
24.6
20
43.8
40.2
3EB
30.2
X
12 B 12 B 12 B 12 B 12 B
4 x ø4.5
)
12.3 SI unit
Replaceable: 8.5
(For mounting)
18 5 L2
28 (L5) L1
Fixed: 4.9
1/4
(Station 1) ----------- (Station n)
[1(P), 5(EA), 3(EB) port]
50RS5- Stations UD
manual override)
(Slide locking
74.3
71.6
68.6
3 2B 2B
7.8
38
27.3
4A 4A
2B
4A
8.4
mounting)
45.8 P = 16 [4(A), 2(B) port]
∗ The above drawing shows when P, E Applicable tube O.D.: ø4, ø5/32" 14.3
port entry is D. : ø6, ø1/4"
: ø8, ø5/16"
Note) These figures show the “SS5Y5-50S5-05B-C8”.
2B 2B
7.8
9.8
38
38
27.3
27.3
4A 4A
One-touch fitting
8.4 1/8 [4(A), 2(B) port]
(Pitch) Applicable tube O.D.: ø4, ø5/32"
[4(A), 2(B) port]
45.8 P = 16
(Pitch) : ø6, ø1/4"
51.6 P = 16 : ø8, ø5/16"
n: Stations 2 3 4 5 6 7 8 9 10 11 12
L1 84 100 116 132 148 164 180 196 212 228 244
L2 74 90 106 122 138 154 170 186 202 218 234
L3 110.5 135.5 148 160.5 173 198 210.5 223 248 260.5 273
L4 100 125 137.5 150 162.5 187.5 200 212.5 237.5 250 262.5
L5 13.5 18 16 14.5 12.5 17 15.5 13.5 18 16.5 14.5
61
Plug-in Metal Base Series SY3000/5000/7000
Valve
Plug-in Type 50/Side Ported
U
SS5Y5-50(R)S5- Stations D -02(D)
Sub-plate
B
D side U side
L3
Plug-in
M5 x 0.8 (External pilot)
5.3 L4
[Pilot EXH port] Manual override
(DIN rail mounting hole pitch: 12.5)
DIN rail holding screw
(For DIN rail mounting)
50
(Pitch)
P = 17.5
(
Push-turn locking slotted type:
Press, then rotate it. )
DIN rail bracket mounting screw 4(A) port side : Blue (For rubber seal)
20.5 19.6 (Light/surge voltage : Gray (For metal seal)
(For DIN rail mounting) suppressor)
2(B) port side : Yellow
Metal Base
DIN rail
B A B A B A B A B A
14 A 14 A 14 A 14 A 14 A
PE
5EA
106.2
5.5
23.2
116.6
35
96.2
20
Plug-in
81.6
20
74.1
1P
24.6
20
43.8
40.2
8
3EB
30.2
X
12 B 12 B 12 B 12 B 12 B
74.3
71.6
68.6
2B 2B
9.8
38
27.3
4A 4A
3
[Plug for external pilot]
2B
8.4 1/4 (For DIN rail
10
(Pitch) mounting)
Plug-in
4A
[4(A), 2(B) port]
14.3
45.8 P = 17.5
n: Stations 2 3 4 5 6 7 8 9 10 11 12
L1 88.5 106 123.5 141 158.5 176 193.5 211 228.5 246 263.5
Manifold Options
L2 78.5 96 113.5 131 148.5 166 183.5 201 218.5 236 253.5
L3 123 135.5 148 173 185.5 210.5 223 235.5 260.5 273 298
L4 112.5 125 137.5 162.5 175 200 212.5 225 250 262.5 287.5
L5 17.5 15 12.5 16 13.5 17.5 15 12.5 16 13.5 17.5
62
Series SY3000/5000/7000
U 02
SS5Y7-50(R)S5- Stations D - KC
C, N (D)
, KN
D side
L3
U side
B
5.3 L4 Manual override
(DIN rail mounting hole pitch: 12.5)
(Pitch) (Push-turn locking slotted type:
Press, then rotate it. )
DIN rail holding screw 52 P = 19 4(A) port side : Blue (For rubber seal)
M5 x 0.8 (External pilot) (For DIN rail mounting) 20.5 19.6 (Light/surge voltage : Gray (For metal seal)
PE: Pilot EXH port suppressor) 2(B) port side : Yellow
DIN rail bracket mounting screw
(For DIN rail mounting)
(DIN rail)
BA BA BA BA B A
5.5
14 A 14 A 14 A 14 A 14 A
PE
5EA
116.7
23.8
28
35
102.1
133.2
92.1
84.6
24
1P
23.8
28.2
49.7
44.1
8
3EB
X
32.1
12 B 12 B 12 B 12 B 12 B
NC
NC
4 x ø4.5
18.1 SI unit
(5.4)
(For mounting)
20.9 5 L2
34.5 M5 x 0.8 (External pilot) (L5) L1
40.5 X: External pilot port
3/8 (Station 1) (Station n)
[1(P), 5(EA), 3(EB) port]
78.3
78.1
84
2B 2B
44.5
3
9.4
32.4
4A 4A
[Plug for external pilot]
2B
10
mounting)
4A
46.6 P = 19
14.3
One-touch fitting
[4(A), 2(B) port]
Applicable tube O.D. : ø8, ø5/16"
∗ The above drawing shows when P, : ø10, ø3/8"
E port entry is D.
Note) These figures show the “SS5Y7-50S5-05B-C10”.
2B 2B
44.5
44.5
10.3
9.4
32.4
31.5
4A 4A
n: Stations 2 3 4 5 6 7 8 9 10 11 12
L1 92 111 130 149 168 187 206 225 244 263 282
L2 82 101 120 139 158 177 196 215 234 253 272
L3 123 148 160.5 185.5 198 223 235.5 260.5 273 298 310.5
L4 112.5 137.5 150 175 187.5 212.5 225 250 262.5 287.5 300
L5 15.5 18.5 15.5 18.5 15 18 15 18 14.5 17.5 14.5
63
Plug-in Metal Base Series SY3000/5000/7000
Valve
Plug-in Type 51/Bottom Ported
M5, 01
SS5Y3-51S5- Stations D- CKC, N,
KN
D side
45.1
(Pitch)
P = 10.5
U side
Manual override
Sub-plate
18.5 19.6 (Light/surge voltage
suppressor) (Push-turn locking slotted type:
Press, then rotate it. )
4(A) port side : Blue (For rubber seal)
: Gray (For metal seal)
Plug-in
2(B) port side : Yellow
B A B A B A B A B A
92.7
14 A 14 A 14 A 14 A 14 A
89
64.4
56.9
21.8 16
12 B 12 B 12 B 12 B 12 B
4 x ø4.5 SI unit
(For mounting)
Metal Base
(Max. 3) L1
(Station 1)--- (Station n)
manual override)
(Slide locking
Plug-in
Panel fitting dimensions
68.3
65.6
62.6
16 17.8 (For 9 stations or more)
32
2 x ø4.5
(For 9 stations or more)
4
(4.1)
21.1
3EB 2B 2B
29.8
: ø4, ø5/32"
52.4
56.4
16.8 16.8
: ø6, ø1/4"
56.4
1P
4 x M4 x 0.7
4 x ø4.5 5EA 4A 4A
4 4
Fitting dimensions for panel mounting
L3 1/8
C2, C3, C4 : 16
: 15
Refer to panel fitting dimensions for details.
Plug-in
32
32
32
17 20.1
14 21.1
29.8
29.8
1P 1P 1P
64
Series SY3000/5000/7000
106.2
116.6
81.6
74.1
20
30.2
12 B 12 B 12 B 12 B 12 B
4 x ø4.5
SI unit
(For mounting)
(Max. 3) L1
(Station 1) ----------- (Station n)
manual override)
(Slide locking
74.3
71.6
68.6
38
Panel fitting dimensions
2 x ø4.5
(For 9 stations or more) 4 x M4 x 0.7, thread depth 5
(4.9)
5
(Pitch) 2 x M4 x 0.7
4 x ø4.5 (For mounting) 50 P = 16
(For 9 stations or more)
20 25.2
24
One-touch fitting
61.6
71.6
4 x M4 x 0.7
: ø6, ø1/4"
20
4 x ø4.5
: ø8, ø5/16"
71.6
1P
5 5
20
L3 5EA 4A 4A
L2 Fitting dimensions for panel mounting
Refer to panel fitting dimensions for details.
C4, C6 : 14.8
: 17.2
1/4
[1(P), 5(EA), 3(EB) port]
L3
L2 Note) These figures show the
C8
“SS5Y5-51S5-05D-C8”.
38
38
40.2
40.2
9.7
17.5
14.5
14.8
1P 1P 1P
65
Plug-in Metal Base Series SY3000/5000/7000
Valve
Plug-in Type 51/Bottom Ported
02
SS5Y7-51(R)S5- Stations D- CKC, N,
KN
(D) D side U side
Manual override
Sub-plate
(Light/surge voltage suppressor) (Push-turn locking slotted type:
Press, then rotate it. )
(Pitch) 4(A) port side : Blue (For rubber seal)
52 P = 19 : Gray (For metal seal)
20.5 19.6 2(B) port side : Yellow
Plug-in
4 x ø4.5
B A B A B A B A B A
(For mounting) 14 A 14 A 14 A 14 A 14 A
116.7
133.2
92.1
84.6
24
32.1
Metal Base
12 B 12 B 12 B 12 B 12 B
NC
NC
SI unit
Plug-in
(For ø12)
(29.5)
78.3
78.1
84
44.5
One-touch fitting
(5.4)
Applicable tube O.D. : ø6, ø1/4"
1/4 : ø8, ø5/16"
[4(A), 2(B) port] : ø10, ø3/8"
: ø12
32.8
33.1
3EB 2B 3EB 2B
1P 1P
(For mounting)
Plug-in
3/8
[1(P), 5(EA), 3(EB) port]
5EA 4A 5EA 4A
(Pitch) M4 x 0.7 thread depth 5
(Max. 3) 52 P = 19
2B 2B
Panel fitting dimensions
46.1
3EB
23
4 x ø4.5 2 x ø4.5
81.1
22
23
27.1
5EA 4A 4A
One-touch fitting
Plug Assembly Part No.
One-touch Fittings/
81.1
72.1
n: Stations 2 3 4 5 6 7 8 9 10 11 12
L1 92 111 130 149 168 187 206 225 244 263 282
L2 82 101 120 139 158 177 196 215 234 253 272
L3 — — — — — — — 107.5 117 126.5 136
66
Type 52 Plug-in Metal Base EX510
Top Ported
Series SY3000/5000/7000
How to Order Manifold
SS5Y 3 52 S5 05 D
Series Wiring type Valve stations
3 SY3000 Nil All double wiring Note 1) Symbol Stations Note
5 SY5000 S All single wiring Note 2) 02 2 stations
All double
7 SY7000 Note 1) All double wiring: 2-position single, double, wiring
3-position and 4-position valves can be 08 8 stations
used on all manifold stations. 02 2 stations
All single
Note 2) All single wiring: Available only for the
Type manifold which has 2-position single for all 12 12 stations
wiring
67
Plug-in Metal Base Series SY3000/5000/7000
Valve
How to Order Valves (With mounting screw) Refer to page 3 for valve specifications.
SY 3 1 3 0 5 1 C6
Sub-plate
Plug-in
Top ported
Metal Base
long periods of time. 02 1/4 SY7000
Type of actuation ∗ Be careful of the energizing time when the
1 Single power saving circuit is selected. Refer to page One-touch fitting (Metric)
2-position 244 for details. Symbol A, B port SY3000 SY5000 SY7000
2 Double
3 Closed center C2 ø2 — —
Plug-in
C3 ø3.2 — —
4 3-position Exhaust center Rated voltage C4 ø4 —
5 Pressure center
5 24 VDC C6
A∗ 4-position N.C./N.C. ø6
B∗ dual N.O./N.O. C8 ø8 —
C∗ 3-port C10 ø10 — —
N.C./N.O. Light/surge voltage suppressor C12 ø12 — —
Plug-in
∗ Only rubber seal type Nil: D:
∗ Back pressure check valve is not available Non-locking Push-turn Nil Round head combination screw
for the 3-position type and the SY7000. push type locking B Hexagon socket head cap screw
regulator.
Protective class
class III (Mark: )
68
Series SY3000/5000/7000
D side U side
68.3
(For DIN rail mounting)
45.1
(Pitch)
P = 10.5 (
Push-turn locking slotted type:
Press, then rotate it. )
(Slide locking manual override) 18.5 19.6 (Light/surge voltage 4(A) port side : Blue (For rubber seal)
suppressor) : Gray (For metal seal)
M5 x 0.8 (External pilot) 2(B) port side : Yellow
[Pilot EXH port]
DIN rail
B A B A B A B A B A
92.7
4A 4A 4A 4A 4A
5EA
89
PE
16.8 17.2
79
15.9 16.2
5.5
35
64.4
56.9
16
1P
29.8
26.6
21.8
2B 2B 2B 2B 2B
3EB
(
32
52RS5- Stations UD
(For DIN rail
mounting)
7.5
11.8
3
[Plug for external pilot]
n: Stations 2 3 4 5 6 7 8 9 10 11 12
L1 71.5 82 92.5 103 113.5 124 134.5 145 155.5 166 176.5
L2 63.5 74 84.5 95 105.5 116 126.5 137 147.5 158 168.5
L3 98 110.5 123 135.5 148 160.5 160.5 173 185.5 198 210.5
L4 87.5 100 112.5 125 137.5 150 150 162.5 175 187.5 200
L5 13.5 14.5 15.5 16.5 17.5 18.5 13 14 15 16 17
69
Plug-in Metal Base Series SY3000/5000/7000
Valve
Plug-in Type 52/Top Ported
U
SS5Y5-52(R)S5- Stations D -(D)
Sub-plate
B
D side U side
L3
Plug-in
DIN rail holding screw 5.3 L4
(For DIN rail mounting) (DIN rail mounting hole pitch: 12.5) Manual override
( )
DIN rail bracket mounting screw (Pitch) Push-turn locking slotted type:
(For DIN rail mounting) 50 P = 16 Press, then rotate it.
74.3 20.5 19.6 4(A) port side : Blue (For rubber seal)
(Slide locking manual override) (Light/surge voltage : Gray (For metal seal)
M5 x 0.8 (External pilot) 68.6 suppressor) 2(B) port side : Yellow
[Pilot EXH port]
Metal Base
01 : 16.2
C : 14.5
DIN rail
5.5
B A B A B A B A B A
4A 4A 4A 4A 4A
PE
5EA
106.2
Plug-in
23.2
116.6
35
96.2
20
81.6
20
74.1
1P
24.6
20
43.8
40.2
40.2
3EB
8
30.2
X
2B 2B 2B 2B 2B
52RS5- Stations UD
72.3
71.6
38
Plug-in
3
[Plug for external pilot]
(For DIN rail
10
n: Stations 2 3 4 5 6 7 8 9 10 11 12
L1 84 100 116 132 148
Manifold Options
70
Series SY3000/5000/7000
U
SS5Y7-52(R)S5- Stations D -(D)
B
D side U side
L3
5.3 L4 Manual override
M5 x 0.8 (External pilot)
PE: Pilot EXH port
(DIN rail mounting hole pitch: 12.5)
( Push-turn locking slotted type:
Press, then rotate it. )
DIN rail holding screw (Pitch) 4(A) port side : Blue (For rubber seal)
84 52 P = 19 : Gray (For metal seal)
(For DIN rail mounting)
(Slide locking manual override) 78.3 (Light/surge voltage 2(B) port side : Yellow
20.5 19.6
DIN rail bracket mounting screw suppressor)
(For DIN rail mounting)
(DIN rail) B A B A B A B A B A
5.5
4 A 4 A 4 A 4 A 4 A
PE
5EA
116.7
23.8
28
102.1
35
133.2
92.1
84.6
24
1P
23.8
28.2
49.7
45.6
44.1
22.6
8
3EB
X
32.1
2B 2B 2B 2B 2B
NC
NC
18.1 4 x ø4.5 1/4
20.9 (For mounting) [4(A), 2(B) port]
34.5 5 L2 One-touch fitting
40.5 (L5) L1 [4(A), 2(B) port]
Applicable tube O.D. : ø6, ø1/4"
3/8 : ø8, ø5/16"
[1(P), 5(EA), 3(EB) port] : ø10, ø3/8"
: ø12
M5 x 0.8 (External pilot)
X: External pilot port
(Station 1) (Station n)
U
52RS5- Stations D
(A, B port: ø12)
3
(110.3)
44.5
mounting)
port entry is D.
n: Stations 2 3 4 5 6 7 8 9 10 11 12
L1 92 111 130 149 168 187 206 225 244 263 282
L2 82 101 120 139 158 177 196 215 234 253 272
L3 123 148 160.5 185.5 198 223 235.5 260.5 273 298 310.5
L4 112.5 137.5 150 175 187.5 212.5 225 250 262.5 287.5 300
L5 15.5 18.5 15.5 18.5 15 18 15 18 14.5 17.5 14.5
71
72
One-touch Fittings/ Type 10, 11, 12 Type 50, 51, 52
Manifold Options Plug-in Connector Connecting Base Plug-in Metal Base Plug-in Sub-plate Valve
Plug Assembly Part No. Manifold Exploded View Manifold Exploded View
Series SY3000/5000/7000 Type 50, 51, 52
Plug-in Metal Base Manifold Exploded View
q
Holding screw
Part no.
No. Description Note
SY3000 SY5000 SY7000
Round head SY3000-23-24A SY5000-221-1A SY7000-221-1A
combination screw (M2 x 32) (M3 x 32.5) (M3 x 36.5) Part numbers shown on the left are
Valve mounting
q for 10 valves (20 pcs.).
screw Hexagon socket SY3000-222-1A SY5000-222-1A SY7000-222-1A (30 pcs. for the SY7000)
head cap screw (M2 x 32) (M3 x 32.5) (M3 x 36.5)
Base gasket Part numbers shown on the left are
w (for plug-in metal base and sub-plate)
SY30M-11-1A SY50M-11-1A SY70M-11-1A for 10 valves (10 pcs.).
e DIN rail VZ1000-11-1- VZ1000-11-4- VZ1000-11-4- Refer to page 225.
Part numbers shown on the left are for
Clamp bracket assembly the clamp bracket assembly for one
r (for plug-in metal base) SY30M-15-2A SY50M-15-2A SY70M-15-2A
manifold (two sets of clamp brackets).
73
Type 50, 51, 52
Plug-in Metal Base Manifold Exploded View Series SY3000/5000/7000
Valve
Manifold Parts No.
Blanking plate assembly (With mounting screw)
Sub-plate
Used when expecting valve additions, or for maintenance.
A structure to prevent screws falling out is in place on the blanking plate, making it much harder for the mounting screws to fall out.
Plug-in
Metal Base
SY30M-26-2A (-B) SY50M-26-2A (-B) SY70M-26-2A (-B)
Plug-in
Refer to pages 226 to 230 for individual SUP/EXH and other options.
5 1 3
(EA) (P) (EB)
Circuit diagram
Plug-in
Manifold Exploded View
Type 10, 11, 12
Plug Assembly Part No.
One-touch Fittings/
Manifold Options
74
75
Plug-in
Bottom ported
Side ported
Top ported
Connector Connecting Base
76
One-touch Fittings/ Type 10, 11, 12 Type 50, 51, 52
Manifold Options Plug-in Connector Connecting Base Plug-in Metal Base Plug-in Sub-plate Valve
Plug Assembly Part No. Manifold Exploded View Manifold Exploded View
Series SY3000/5000/7000 Type 10, 11, 12
Plug-in Connector Connecting Base
Manifold Specifications
( )( )
Enclosure (Based on IEC60529) EX500
IP40 IP67∗ IP40 IP67∗ I/O unit:
gateway (Partially IP20
partially IP40)
IP40 unit, input
unit: IP65
∗ In the case of a metal seal, there are restrictions in the operating environment. Refer to the Specific Product Precautions (page 242).
77
Type 10, 11, 12
Plug-in Connector Connecting Base Series SY3000/5000/7000
Valve
Manifold Flow-rate Characteristics Note 1)/Manifold Weight
Valve Seal Type: Rubber Seal
Sub-plate
Port size Valve flow-rate characteristics
Weight: W [g] Note 2)
Model 1, 3/5 4, 2 1→4/2 (P→A/B) 4/2→5/3 (A/B→E)
(n: stations)
(P, E) (A, B) C [dm3/(s·bar)] b C [dm3/(s·bar)] b
Plug-in
SS5Y3-10 (Side ported) C8 C6 1.4 0.30 1.6 0.19 28.9n + 293
SS5Y3-12 (Top ported) C8 C6 1.2 0.29 1.3 0.19 25.1n + 314
SS5Y5-10 (Side ported) C10 C8 3.3 0.30 3.6 0.17 74.7n + 398
SS5Y5-11 (Bottom ported) C10 C8 3.3 0.29 4.2 0.26 76.8n + 445
SS5Y5-12 (Top ported) C10 C8 2.8 0.27 3.8 0.23 66.3n + 417
SS5Y7-10 (Side ported) C12 C12 6.2 0.23 5.9 0.20 106.6n + 496
Metal Base
SS5Y7-11 (Bottom ported) C12 C12 6.2 0.25 6.6 0.21 117.9n + 532
SS5Y7-12 (Top ported) C12 C12 5.6 0.31 5.7 0.24 84.1n + 519
Plug-in
Port size Valve flow-rate characteristics
Weight: W [g] Note 2)
Model 1, 3/5 4, 2 1→4/2 (P→A/B) 4/2→5/3 (A/B→E)
(n: stations)
(P, E) (A, B) C [dm3/(s·bar)] b C [dm3/(s·bar)] b
SS5Y3-10 (Side ported) C8 C6 1.2 0.19 1.3 0.18 28.9n + 293
SS5Y3-12 (Top ported)
Plug-in
Manifold Exploded View
Type 10, 11, 12
Plug Assembly Part No.
One-touch Fittings/
Manifold Options
78
Series SY3000/5000/7000
Single solenoid valve is installed to all double wiring. (in the case of all double wiring)
(Manifold specification sheet is not necessary.)
Solenoid Connector side
(D-sub connector etc.)
Common (+, –)
SOL.a
Station 1
SOL.b
SOL.a Station 2
Unused terminal
SOL.a Station 3
SOL.b
···
Double solenoid Single solenoid Double solenoid
Station 3 (Double wiring) Station 1
Station 2
Common (+, –)
SOL.a Station 1
SOL.b
SOL.a Station 2
SOL.a
SOL.b Station 3
···
Note) These diagrams are for the purpose of explanation, and differ from the connector wiring used for testing.
79
80
One-touch Fittings/ Type 10, 11, 12 Type 50, 51, 52
Manifold Options Plug-in Connector Connecting Base Plug-in Metal Base Plug-in Sub-plate Valve
Plug Assembly Part No. Manifold Exploded View Manifold Exploded View
Type 10
Side Ported
Plug-in Connector Connecting Base
Type 11 D-sub Connector Flat Ribbon Cable PC Wiring
Series SY3000/5000/7000
Bottom Ported
RoHS
How to Order Manifold
81
Plug-in Connector Connecting Base Series SY3000/5000/7000
Valve
P, E port entry SUP/EXH block assembly Mounting and Option
Sub-plate
U U side (2 to 10 stations) Nil Internal pilot Option DIN Rail Option
Symbol Mounting
D D side (2 to 10 stations) Internal pilot, Name plate Station number Nil Direct mounting
S
B Both sides (2 to 24 stations) Built-in silencer Nil — — 0 Without DIN rail (with bracket)
Direct
Plug-in
R External pilot AA mounting 3 For 3 stations Specify a longer rail
∗ 3/5(E) port is plugged for the BA — than the total length
built-in silencer type. D — — 24 For 24 stations of specified stations.
DIN rail
A mounting
B —
Note 1) Enter the number of stations inside when it is larger than the
number of valve stations. (Refer to “DIN Rail Option” above.)
Note 2) Only direct mounting is available for Type 11 (Bottom ported).
Metal Base
Note 3) Refer to page 247 for the fixation of DIN rail mounting type manifold.
Plug-in
Type 10/Side ported Type 11/Bottom ported Type 10/Side ported Type 11/Bottom ported
Symbol A, B port Symbol A, B port
SY3000 SY5000 SY7000 SY5000 SY7000 SY3000 SY5000 SY7000 SY5000 SY7000
C2 ø2 — — — — N1 ø1/8" — — — —
C3 ø3.2 — — — — N3 ø5/32" — —
Straight
C4 ø4 — — N7 ø1/4"
C6 ø6 N9 ø5/16" —
Elbow Note)
B4 ø4 — — — BN11 ø3/8" — — — —
Downward
Plug-in
Elbow port, mixed sizes
LM∗ (Including upward and — —
downward piping)
P, E port size
Protective class
class III (Mark: )
82
Series SY3000/5000/7000
How to Order Valves (With mounting screw) Refer to page 3 for valve specifications.
SY 3 1 0 0 5 1
Base mounted
Type of actuation
1 Single E: F:
2
2-position
Double Coil type Push-turn Slide locking
3 Closed center Nil Standard locking lever type
4 3-position Exhaust center T With power saving circuit (Continuous duty type) type
5 Pressure center ∗ Be sure to select the power saving circuit type
A∗ 4-position N.C./N.C. when the valve is continuously energized for
B∗ dual N.O./N.O. long periods of time.
C∗ 3-port N.C./N.O. ∗ Be careful of the energizing time when the ∗ Refer to page 14 for with the safety slide locking
power saving circuit is selected. Refer to page manual override.
∗ Only rubber seal type is available for the 244 for details.
4-position dual 3-port valve.
Protective class
class III (Mark: )
83
Plug-in Connector Connecting Base Series SY3000/5000/7000
Valve
Plug-in Type 10/Side Ported
C2
U
SS5Y3-10F 21 - Stations D - C3,
C4, N3 (D)
N1
Sub-plate
B C6, N7
D side U side
Manual override Note 2)
DIN rail holding screw (L5) L1
(Push-turn locking slotted type:
)
Plug-in
(For DIN rail mounting) (8) Press, then rotate it.
4(A) port side : Blue (For rubber seal)
Applicable connector: D-sub ( JIS-X-5101
MIL-C-24308 )
equivalent (Light/surge voltage suppressor) : Gray (For metal seal)
2(B) port side : Yellow
(5.5)
(8)
LOCK
B A B A B A B A B A
(35)
92.6
14 A 14 A 14 A 14 A 14 A
70.6
83
Metal Base
60.5
FREE
(40.9)
44.8
4.6
12 B 12 B 12 B 12 B 12 B
Plug-in
2 x M2.6
4.6
9.5
1.7
(4.9)
)
2 x 4-40 UNC
C6: 3.6
N7: 7.4
(Connector entry
[4(A), 2(B) port: 4 x M4 mounting hole
N (inch size)] upward direction)
(Fitting for the type with P/E
(
19.6 L2 1.5 ports on the U and/or D sides)
(L4)
63.1
13.6
10.6
56.6
48.6
3/5 E 2 B2 B2 B2 B2 B 3/5 E
40.2
21.6
4 A4 A4 A4 A4 A
18
Plug-in
Applicable tube O.D.: ø8, ø5/16"
n: Stations 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
L1
Manifold Options
88.6 99.1 109.6 120.1 130.6 141.1 151.6 162.1 172.6 183.1 193.6 204.1 214.6 225.1 235.6 246.1 256.6 267.1 277.6 288.1 298.6 309.1 319.6
L2 63 73.5 84 94.5 105 115.5 126 136.5 147 157.5 168 178.5 189 199.5 210 220.5 231 241.5 252 262.5 273 283.5 294
L3 123 135.5 148 160.5 160.5 173 185.5 198 210.5 223 223 235.5 248 260.5 273 285.5 298 298 310.5 323 335.5 348 360.5
L4 112.5 125 137.5 150 150 162.5 175 187.5 200 212.5 212.5 225 237.5 250 262.5 275 287.5 287.5 300 312.5 325 337.5 350
L5 20.5 21.5 22.5 23.5 18 19 20 21 22 23 18 19 20 21 22 23 23.5 18.5 19.5 20.5 21.5 22.5 23.5
84
Series SY3000/5000/7000
U C4, N3
SS5Y5-10F 21 - Stations D - C6, N7 (D)
B C8, N9
D side U side
Manual override Note 2)
(L5) L1
DIN rail holding screw
(For DIN rail mounting) (8)
( Push-turn locking slotted type:
Press, then rotate it. )
4(A) port side : Blue (For rubber seal)
Applicable connector: D-sub ( JIS-X-5101
MIL-C-24308 )
equivalent
DIN rail
(Light/surge voltage suppressor)
: Gray (For metal seal)
2(B) port side : Yellow
(5.5)
(8)
LOCK
BA BA BA BA BA
(35)
14 A 14 A 14 A 14 A 14 A
70.6
97.5
113.4
FREE
81.2
(61.7)
65.6
5.5
12 B 12 B 12 B 12 B 12 B
10.9
30.3
4.7
2 x M2.6
(5.9)
(8.3)
4 x M5 mounting hole
2 x 4-40 UNC
[4(A), 2(B) port: 21.9 L2 1.5 (Fitting for the type with P/E
N (inch size)] ports on the U and/or D sides)
(5.3) (L4)
(Connector entry upward direction) (DIN rail mounting hole pitch: 12.5)
(L3)
One-touch fitting
[4(A), 2(B) port]
(Station 1) ----------- (Station n) Applicable tube O.D.: ø4, ø5/32"
: ø6, ø1/4"
: ø8, ø5/16"
6.1
1 P 1 P
14.1
73.2
(62.7)
8.7
2 B2 B2 B2 B2 B
56.6
48.6
12.4
3/5 E 3/5 E
33.4
29.1
4 A4 A4 A4 A4 A
One-touch fitting
(For DIN rail
(Pitch)
(7.5)
mounting)
n: Stations 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
L1 108.4 124.4 140.4 156.4 172.4 188.4 204.4 220.4 236.4 252.4 268.4 284.4 300.4 316.4 332.4 348.4 364.4 380.4 396.4 412.4 428.4 444.4 460.4
L2 80 96 112 128 144 160 176 192 208 224 240 256 272 288 304 320 336 352 368 384 400 416 432
L3 148 160.5 173 198 210.5 223 235.5 260.5 273 285.5 298 323 335.5 348 373 385.5 398 410.5 435.5 448 460.5 485.5 498
L4 137.5 150 162.5 187.5 200 212.5 225 250 262.5 275 287.5 312.5 325 337.5 362.5 375 387.5 400 425 437.5 450 475 487.5
L5 23 21 19.5 24 22 20.5 18.5 23 21.5 19.5 18 22.5 20.5 19 23.5 21.5 20 18 22.5 21 19 23.5 22
85
Plug-in Connector Connecting Base Series SY3000/5000/7000
Valve
Plug-in Type 10/Side Ported
U C6, N7
C10, N11(D)
SS5Y7-10F 12- Stations DB - C8, N9
Sub-plate
C12
D side U side
Manual override Note 2)
DIN rail holding screw (L5) L1
(Push-turn locking slotted type:
)
Plug-in
(For DIN rail mounting) Press, then rotate it.
(8)
(
JIS-X-5101
Applicable connector: D-sub MIL-C-24308 equivalent ) (Light/surge voltage suppressor)
4(A) port side : Blue (For rubber seal)
: Gray (For metal seal)
2(B) port side : Yellow
(8)
(DIN rail)
LOCK
B A B A B A B A B A
(35)
Metal Base
14 A 14 A 14 A 14 A 14 A
70.6
128.8
115
FREE
(5.5)
96.7
(77.1)
79.5
Plug-in
12 B 12 B 12 B 12 B 12 B
44.2
5.5
8.8
2 x M2.6
3.9
(6)
(9.3)
4 x M5 mounting hole
One-touch fitting
[4(A), 2(B) port]
2
1 P 1 P
2 B2 B2 B2 B2 B 82.7
(62.7)
Plug-in
56.6
48.6
14.2
3/5 E 3/5 E
11.1
8.7
35.2
31.6
4 A4 A4 A4 A4 A
mounting)
39.5 20.5 P = 19
(14.3)
n: Stations 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
Manifold Options
L1 121.2 140.2 159.2 178.2 197.2 216.2 235.2 254.2 273.2 292.2 311.2 330.2 349.2 368.2 387.2 406.2 425.2 444.2 463.2 482.2 501.2 520.2 539.2
L2 94 113 132 151 170 189 208 227 246 265 284 303 322 341 360 379 398 417 436 455 474 493 512
L3 160.5 173 198 210.5 235.5 248 273 285.5 310.5 323 348 360.5 385.5 398 423 435.5 460.5 485.5 498 523 535.5 560.5 573
L4 150 162.5 187.5 200 225 237.5 262.5 275 300 312.5 337.5 350 375 387.5 412.5 425 450 475 487.5 512.5 525 550 562.5
L5 22.5 19.5 22.5 19 22 19 22 18.5 21.5 18.5 21.5 18 21 18 21 17.5 20.5 23.5 20.5 23.5 20 23 20
86
Series SY3000/5000/7000
U C2
SS5Y3-10FW 12 - C4, N3 (D)
Stations D - C3, N1
B C6, N7
D side U side
(L5) Manual override Note 2)
L1
DIN rail holding screw
(15)
(Push-turn locking slotted type:
Press, then rotate it. )
(For DIN rail mounting) 4(A) port side : Blue (For rubber seal)
(Light/surge voltage suppressor) : Gray (For metal seal)
(Connector entry upward direction)
2(B) port side : Yellow
DIN rail
(8)
(5.5)
B A B A B A B A B A
(35)
14 A 14 A 14 A 14 A 14 A
92.6
83
70.6
60.5
(40.9)
38.7
12 B 12 B 12 B 12 B 12 B
4.6
3.4
4.6
1.7
(4.9)
)C6: 3.6
N7: 7.4
2 x M2.6
2 x 4-40 UNC 4 x M4 mounting hole
(
(Station 1) (Station n)
One-touch fitting
One-touch fitting [4(A), 2(B) port]
[1(P), 3/5(E) port] Applicable tube O.D.: ø2, ø1/8"
Applicable tube O.D.: ø8, ø5/16" : ø3, ø5/32"
4.5 : ø4, ø1/4"
: ø6
1 P 1 P
(61.1)
63.1
56.6
10.6
13.6
3/5 E 2 B2 B2 B2 B2 B 3/5 E
40.2
4 A4 A4 A4 A4 A
21.6
23
18
(17.8)
(For DIN rail
(7.5)
(Pitch)
mounting)
(11.8)
n: Stations 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
L1 105.5 116 126.5 137 147.5 158 168.5 179 189.5 200 210.5 221 231.5 242 252.5 263 273.5 284 294.5 305 315.5 326 336.5
L2 63 73.5 84 94.5 105 115.5 126 136.5 147 157.5 168 178.5 189 199.5 210 220.5 231 241.5 252 262.5 273 283.5 294
L3 135.5 148 160.5 173 185.5 198 198 210.5 223 235.5 248 260.5 260.5 273 285.5 298 310.5 323 323 335.5 348 360.5 373
L4 125 137.5 150 162.5 175 187.5 187.5 200 212.5 225 237.5 250 250 262.5 275 287.5 300 312.5 312.5 325 337.5 350 362.5
L5 17.5 18.5 19.5 20.5 21.5 22.5 17 18 19 20 21 22 17 18 19 20 21 22 16.5 17.5 18.5 19.5 20.5
87
Plug-in Connector Connecting Base Series SY3000/5000/7000
Valve
Plug-in Type 10/Side Ported
U C4, N3
SS5Y5-10FW 12 - Stations D- C6, N7 (D)
Sub-plate
B C8, N9
D side U side
Manual override Note 2)
(L5) L1
(
Push-turn locking slotted type:
Press, then rotate it. )
Plug-in
DIN rail holding screw
(15) 4(A) port side : Blue (For rubber seal)
(For DIN rail mounting) (Light/surge voltage suppressor)
(Connector entry upward direction) : Gray (For metal seal)
2(B) port side : Yellow
DIN rail
(8)
(5.5)
B A B A B A B A B A
(35)
14 A 14 A 14 A 14 A 14 A
Metal Base
97.5
70.6
113.4
81.2
(61.7)
59.5
5.5
12 B 12 B 12 B 12 B 12 B
24.2
Plug-in
10.9
4.7
2 x M2.6 (5.9)
(8.3)
(Station 1) (Station n)
One-touch fitting
One-touch fitting [4(A), 2(B) port]
[1(P), 3/5(E) port] Applicable tube O.D.: ø4, ø5/32"
1 P 1 P
14.1
73.2
8.7
(61.1)
2 B2 B2 B2 B2 B
56.6
3/5 E 3/5 E
33.4
29.1
23
4 A4 A4 A4 A4 A
Plug-in
12.4
(Pitch)
(7.5)
mounting)
50 18 P=16 (20.5)
(11.8)
n: Stations 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
Manifold Options
L1 122.5 138.5 154.5 170.5 186.5 202.5 218.5 234.5 250.5 266.5 282.5 298.5 314.5 330.5 346.5 362.5 378.5 394.5 410.5 426.5 442.5 458.5 474.5
L2 80 96 112 128 144 160 176 192 208 224 240 256 272 288 304 320 336 352 368 384 400 416 432
L3 160.5 173 185.5 210.5 223 235.5 248 273 285.5 298 310.5 335.5 348 360.5 385.5 398 410.5 423 448 460.5 473 498 510.5
L4 150 162.5 175 200 212.5 225 237.5 262.5 275 287.5 300 325 337.5 350 375 387.5 400 412.5 437.5 450 462.5 487.5 500
L5 21.5 19.5 18 22.5 20.5 19 17 21.5 20 18 16.5 21 19 17.5 22 20 18.5 16.5 21 19.5 17.5 22 20.5
88
Series SY3000/5000/7000
U C6, N7
SS5Y7-10FW 12 - Stations D - C8, N9 (D)
B C10, N11
C12
D side U side
(8)
(DIN rail)
B A B A B A B A B A
(35)
14 A 14 A 14 A 14 A 14 A
70.6
128.8
115
(5.5)
96.7
(77.1)
74.9
12 B 12 B 12 B 12 B 12 B
5.5
39.6
8.8
3.9
(6)
(9.3)
2 x M2.6
(17.9)
1 P 1 P
82.7
2 B2 B2 B2 B2 B
(61.1)
56.6
3/5 E 3/5 E
11.1
8.7
35.2
31.6
4 A4 A4 A4 A4 A
23
14.2
(Pitch) (21.7)
(10)
mounting)
(14.3)
55 20.5 P = 19
n: Stations 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
L1 136.7 155.7 174.7 193.7 212.7 231.7 250.7 269.7 288.7 307.7 326.7 345.7 364.7 383.7 402.7 421.7 440.7 459.7 478.7 497.7 516.7 535.7 554.7
L2 94 113 132 151 170 189 208 227 246 265 284 303 322 341 360 379 398 417 436 455 474 493 512
L3 173 185.5 210.5 223 248 260.5 285.5 298 323 335.5 360.5 385.5 398 423 435.5 460.5 473 498 510.5 535.5 548 573 585.5
L4 162.5 175 200 212.5 237.5 250 275 287.5 312.5 325 350 375 387.5 412.5 425 450 462.5 487.5 500 525 537.5 562.5 575
L5 20.5 17 20 17 20 16.5 19.5 16.5 19.5 16 19 22 19 22 18.5 21.5 18.5 21.5 18 21 18 21 17.5
89
Plug-in Connector Connecting Base Series SY3000/5000/7000
Valve
Plug-in Type 10/Side Ported
P C2
U D side U side
PH 2 - Stations D - C4, N3 (D)
SS5Y3-10 PG 1 C3, N1
Sub-plate
B C6, N7 (L5) L1 Manual override Note 2)
J
Plug-in
2(B) port side : Yellow
voltage suppressor)
(8)
(5.5)
LOCK
B A B A B A B A B A
(35)
92.6
14 A 14 A 14 A 14 A 14 A
70.6
83
60.5
FREE
(40.9)
44.8
Metal Base
4.6
12 B 12 B 12 B 12 B 12 B
4.6
9.5
N7: 7.4 )
1.7
(4.9)
(Fitting for the type
3.6
Applicable connector:
with P/E ports on the
(C6:
26 pins MIL type with strain relief
Plug-in
U and/or D sides)
(Conforming to MIL-C-83503) 19.6 L2 1.5 4 x M4 mounting hole
(5.3) (L4)
(DIN rail mounting hole pitch: 12.5)
(L3)
For PC wiring with power One-touch fitting
63.1
10.6
13.6
56.6
48.6
3/5 E 2 B2 B2 B2 B2 B 3/5 E
40.2
4 A4 A4 A4 A4 A
21.6
18
mounting)
[1(P), 3/5(E) port] (11.8)
Applicable tube O.D.: ø8, ø5/16"
Plug-in
10PJG (20 pins) 10PH (10 pins) 10G (20 pins)
For PC wiring Switch for locking a connector
+ (Positive)
LOCK
LOCK
PCW type
FREE
44.8
n: Stations 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
Manifold Options
L1 88.6 99.1 109.6 120.1 130.6 141.1 151.6 162.1 172.6 183.1 193.6 204.1 214.6 225.1 235.6 246.1 256.6 267.1 277.6 288.1 298.6 309.1 319.6
L2 63 73.5 84 94.5 105 115.5 126 136.5 147 157.5 168 178.5 189 199.5 210 220.5 231 241.5 252 262.5 273 283.5 294
L3 123 135.5 148 160.5 160.5 173 185.5 198 210.5 223 223 235.5 248 260.5 273 285.5 298 298 310.5 323 335.5 348 360.5
L4 112.5 125 137.5 150 150 162.5 175 187.5 200 212.5 212.5 225 237.5 250 262.5 275 287.5 287.5 300 312.5 325 337.5 350
L5 20.5 21.5 22.5 23.5 18 19 20 21 22 23 18 19 20 21 22 23 23.5 18.5 19.5 20.5 21.5 22.5 23.5
90
Series SY3000/5000/7000
P
U C4, N3
PH 2 - Stations D - C6, N7 (D)
SS5Y5-10 PG 1 D side U side
J B C8, N9 (L5) L1 Manual override Note 2)
(5.5)
(8)
LOCK
BA BA BA BA BA
(35)
14 A 14 A 14 A 14 A 14 A
70.6
97.5
113.4
FREE
81.2
(61.7)
65.6
5.5
12 B 12 B 12 B 12 B 12 B
30.3
10.9
4 x M5 mounting hole
4.7
(5.9)
(8.3)
Applicable connector: (Fitting for the type with P/E
26 pins MIL type with strain relief 21.9 L2 1.5
ports on the U and/or D sides)
(Conforming to MIL-C-83503) (5.3) (L4)
(DIN rail mounting hole pitch: 12.5)
(L3) One-touch fitting
For PC wiring with power
supply terminals [4(A), 2(B) port]
Applicable tube O.D.: ø4, ø5/32"
(Station 1)----------- (Station n) : ø6, ø1/4"
: ø8, ø5/16"
18.8
(75.4)
1 P 1 P
14.1
73.2
8.7
2 B2 B2 B2 B2 B
56.6
48.6
12.4
3/5 E 3/5 E
33.4
29.1
4 A4 A4 A4 A4 A
(Pitch)
mounting)
(11.8)
[1(P), 3/5(E) port] 7.9 35.9 18 P=16 (20.5)
Applicable tube O.D.: ø10, ø3/8"
+(Positive)
LOCK
dimensions of A or B port
FREE
top-ported type.
65.6
n: Stations 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
L1 108.4 124.4 140.4 156.4 172.4 188.4 204.4 220.4 236.4 252.4 268.4 284.4 300.4 316.4 332.4 348.4 364.4 380.4 396.4 412.4 428.4 444.4 460.4
L2 80 96 112 128 144 160 176 192 208 224 240 256 272 288 304 320 336 352 368 384 400 416 432
L3 148 160.5 173 198 210.5 223 235.5 260.5 273 285.5 298 323 335.5 348 373 385.5 398 410.5 435.5 448 460.5 485.5 498
L4 137.5 150 162.5 187.5 200 212.5 225 250 262.5 275 287.5 312.5 325 337.5 362.5 375 387.5 400 425 437.5 450 475 487.5
L5 23 21 19.5 24 22 20.5 18.5 23 21.5 19.5 18 22.5 20.5 19 23.5 21.5 20 18 22.5 21 19 23.5 22
91
Plug-in Connector Connecting Base Series SY3000/5000/7000
Valve
Plug-in Type 10/Side Ported
Sub-plate
J
G C12
DIN rail holding screw
(L5) L1 (
Push-turn locking slotted type:
Press, then rotate it. )
(For DIN rail mounting) (8) (Light/surge voltage suppressor) 4(A) port side : Blue (For rubber seal)
: Gray (For metal seal)
Triangle mark (Connector entry upward direction) 2(B) port side : Yellow
Plug-in
(8)
(DIN rail)
LOCK
B A B A B A B A B A
(35)
14 A 14 A 14 A 14 A 14 A
70.6
128.8
115
FREE
(5.5)
96.7
Metal Base
(77.1)
79.5
44.2
12 B 12 B 12 B 12 B 12 B
5.5
Plug-in
8.8
3.9
(6)
Applicable connector:
(9.3)
2
“SS5Y7-10P2-05D-C8”.
Note 2) Refer to page 183 for 1 P 1 P
82.7
(75.4)
2 B2 B2 B2 B2 B
dimensions of external pilot,
56.6
3/5 E 3/5 E
11.1
8.7
35.2
31.6
4 A4 A4 A4 A4 A
slide locking manual override.
Note 3) Refer to page 188 for
dimensions of A or B port
top-ported type.
Note 4) Only connectors are different
mounting)
(14.3)
39.5 20.5 P = 19
10G. L1 to L5 dimensions are
the same as 10P type.
Plug-in
For PC wiring LED Switch for locking a connector
Triangle mark
Triangle mark Power supply terminal Triangle mark
LOCK
LOCK
+(Positive)
PCW type
PCW type
FREE
FREE
65.6
n: Stations 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
Manifold Options
L1 121.2 140.2 159.2 178.2 197.2 216.2 235.2 254.2 273.2 292.2 311.2 330.2 349.2 368.2 387.2 406.2 425.2 444.2 463.2 482.2 501.2 520.2 539.2
L2 94 113 132 151 170 189 208 227 246 265 284 303 322 341 360 379 398 417 436 455 474 493 512
L3 160.5 173 198 210.5 235.5 248 273 285.5 310.5 323 348 360.5 385.5 398 423 435.5 460.5 485.5 498 523 535.5 560.5 573
L4 150 162.5 187.5 200 225 237.5 262.5 275 300 312.5 337.5 350 375 387.5 412.5 425 450 475 487.5 512.5 525 550 562.5
L5 22.5 19.5 22.5 19 22 19 22 18.5 21.5 18.5 21.5 18 21 18 21 17.5 20.5 23.5 20.5 23.5 20 23 20
92
Plug-in Connector Connecting Base
Type 12
Top Ported D-sub Connector Flat Ribbon Cable PC Wiring
SS5Y 3 12 F 1 05 U RoHS
Refer to pages 186 to 188 for
dimensions of Type 12/Top ported type.
Series Connector entry direction
3 SY3000 1: Upward 2: Lateral ∗ The connector entry direc-
5 SY5000 tion for connector type "FW"
7 SY7000 D-sub connector <IP67>
can not be rotated. If it is
Connector type LOC
K
LOC
K
necessary to change, order
F: D-sub connector FW: D-sub connector P: Flat ribbon cable PG: Flat ribbon cable FRE
E
FRE
E
connector block assembly
<IP40> <IP67> (26 pins) (20 pins) (page 208) separately.
(25 pins) New (25 pins)
Valve stations
LOC
K
LOC
K
LOC
K
F/FW: D-sub connector (25 pins) P: Flat ribbon cable (26 pins)
FRE
E
FRE
E
FRE
E
Symbol Stations Note Symbol Stations Note
02 2 stations 02 2 stations
Double wiring Note 1) Double wiring Note 1)
PH: Flat ribbon cable J: PC wiring (20 pins) G: PC wiring (20 pins) 12 12 stations 12 12 stations
with power
(10 pins) Yellow ink New supply terminal 02 2 stations Specified layout Note 2) 02 2 stations Specified layout Note 2)
Yellow ink (Available up to (Available up to
24 24 stations 24 solenoids) 24 24 stations 24 solenoids)
LOC LOC
PG: Flat ribbon cable (20 pins) PH: Flat ribbon cable (10 pins)
K K
FRE PC FRE
Symbol Stations Note Symbol Stations Note
W ty
02 2 stations 02 2 stations
E E
pe
Manifold base
3
93
Plug-in Connector Connecting Base Series SY3000/5000/7000
Valve
How to Order Valves (With mounting screw) Refer to page 3 for valve specifications.
SY 3 1 3 0 5 1 C6
Sub-plate
Plug-in
Top ported
Metal Base
Type of actuation pressure type. 02 1/4 SY7000
1 Single One-touch fitting (Metric)
2
2-position
Double
Coil type Symbol A, B port SY3000 SY5000 SY7000
3 Closed center Nil Standard
C2 ø2 — —
4 T With power saving circuit (Continuous duty type)
Plug-in
3-position Exhaust center C3 ø3.2 — —
5 Pressure center ∗ Be sure to select the power saving circuit type C4 ø4 —
A∗ 4-position N.C./N.C. when the valve is continuously energized for
C6 ø6
long periods of time.
B∗ dual N.O./N.O. C8 ø8 —
∗ Be careful of the energizing time when the
C∗ 3-port N.C./N.O. power saving circuit is selected. Refer to page C10 ø10 — —
∗ Only rubber seal type is available for the 244 for details. C12 ø12 — —
Plug-in
H Built-in NZ common Type of mounting screw
∗ Only rubber seal type. Manifold installed type is ∗ Only “Z” and “NZ” types are available for with the Nil Round head combination screw
available if the back pressure check valve is power saving circuit. B Hexagon socket head cap screw
94
Series SY3000/5000/7000
Electrical Wiring Specifications Cable Assembly
015 015
D-sub connector
AXT100-DS25- 030 (N) [IP40] SY30M-DS25- 030 (N) [IP67]
050 050
Nil: Metric Nil: Metric
If alignment is not specified,
N: Inch N: Inch
the internal wiring is double
1
14 2 wiring (connected to SOL. a
15 and SOL. b) regardless of Cable Cable
3 0.3 mm2 x 25 cores 0.3 mm2 x 25 cores
16 4 number of stations, valve
17 O.D. ø1.4 O.D. ø1.4
5 and option types.
18 6 Approx. ø10
19 7
20 8
21 Approx. ø8
9 Connector terminal no. Seal (Length)
22 10
23 015
11
24 12 Molded cover
L
25 13 2 x M2.6 x 0.45
or Seal (Length)
44
2 x 4 − 40 UNC 015
Connector JBZ-25S-3 Connector hood
Terminal no. Polarity made by J.S.T. Mfg.
L
SOL.a Co.,Ltd.
1 (−) (+) (2.4)
Station 1 SOL.b 55
14 (−) (+)
SOL.a Socket side 2 x M2.6 x 0.45
2 (−) (+) 14 25
(86.5)
Station 2 SOL.b or
15 (−) (+)
SOL.a Terminal no. 2 x 4 − 40 UNC
16
3 (−) (+)
Station 3 SOL.b
16 (−) (+)
SOL.a 1 13
4 (−) (+)
8.7
Station 4 SOL.b 47.04
17 (−) (+)
SOL.a
5 (−) (+)
Station 5 SOL.b
18 (−) (+) Connector
SOL.a
6 (−) (+) JBZ-25S-3 made by
Station 6 SOL.b
19 (−) (+) J.S.T. Mfg. Co.,Ltd.
SOL.a
7 (−) (+)
Station 7 SOL.b 14…………25 Socket side
20 (−) (+)
SOL.a
8 (−) (+)
Station 8 SOL.b
22
21 (−) (+) Terminal no.
SOL.a
9 (−) (+)
Station 9 SOL.b 1…………13
22 (−) (+) 47.04
SOL.a
10 (−) (+)
Station 10 SOL.b
23 (−) (+) D-sub connector cable assembly [IP40] D-sub connector cable assembly [IP67]
SOL.a
11 (−) (+)
Station 11 SOL.b Cable Cable
24 (−) (+) Assembly part no. Note Assembly part no. Note
SOL.a length (L) length (L)
12 (−) (+)
Station 12 SOL.b 1.5 m AXT100-DS25-015 1.5 m SY30M-DS25-015
25 (−) (+) Cable Cable
3m AXT100-DS25-030 0.3 mm2 x 25 cores 3m SY30M-DS25-030
0.3 mm2 x 25 cores
COM. 5m AXT100-DS25-050 5m SY30M-DS25-050
13 (+) (−) ∗ Be sure to use the connector cable assembly
∗ When using a standard commercial
Positive Negative connector, use a 25-pin type female in the table, to satisfy enclosure IP67.
common common connector conforming to MIL-C-24308. ∗ Cannot be used for movable wiring.
Note) When using a valve with no polarity, either positive ∗ Cannot be used for movable wiring.
common or negative common can be used. ∗ Lengths other than the above are also
available. Please contact SMC for details.
Brown
White
White
White
Orange
Orange
Orange
Yellow
Yellow
Yellow
Purple
Purple
Black
Black
Gray
Gray
Blue
Blue
Pink
Pink
Pink
Red
Red
color
White
White
White
White
White
Dot
Black
Black
Black
Black
Black
None
None
None
None
None
None
None
None
None
None
Red
Red
Red
Red
Red
marking
95
Plug-in Connector Connecting Base Series SY3000/5000/7000
Valve
Electrical Wiring Specifications
Flat ribbon cable connector
If alignment is not specified, the internal wiring
is double wiring (connected to SOL. a and
26 25
24 23
SOL. b) regardless of number of stations,
22 21 valve and option types.
Sub-plate
20 19
18 17
16 15
14 13
12 11 Connector terminal no.
Plug-in
10 9
8 7
Triangle mark indicator position
6 5
4 3
2 1
P: Flat ribbon cable (26 pins) PG: Flat ribbon cable (20 pins) G: Flat ribbon cable (20 pins)
<Double wiring> <Double wiring> PC wiring (with power supply terminal)
Metal Base
Terminal no. Polarity Terminal no. Polarity Terminal no.
SOL.a 1 (−) (+) SOL.a 1 (−) (+) SOL.a
Station 1 SOL.b Station 1 SOL.b 20 19 20
2 (−) (+) 2 (−) (+) Station 1 SOL.b
SOL.a SOL.a 18
3 (−) (+) 3 (−) (+)
Station 2 SOL.b Station 2 SOL.b SOL.a 16
4 (−) (+) 4 (−) (+)
SOL.a SOL.a 18 17 Station 2 SOL.b
5 (−) (+) 5 (−) (+)
Plug-in
14
Station 3 SOL.b Station 3 SOL.b
6 (−) (+) 6 (−) (+) SOL.a
SOL.a SOL.a 12
7 (−) (+) 7 (−) (+) 16 15 Station 3
Station 4 SOL.b Station 4 SOL.b SOL.b 10
8 (−) (+) 8 (−) (+)
SOL.a 9 (−) (+) SOL.a 9 (−) (+) SOL.a 8
Station 5 SOL.b Station 5 SOL.b Station 4
10 (−) (+) 10 (−) (+) 14 13 SOL.b 6
SOL.a 11 (−) (+) SOL.a 11 (−) (+) SOL.a
Plug-in
18 (−) (+)
SOL.a 1,2
16 (−) (+) 24 VDC − +
Station 2 SOL.b 14 (−)
PH: Flat ribbon cable (10 pins) (+)
SOL.a Power supply terminal
12 (−) (+)
9 (+) (−)
One-touch Fittings/
either positive common or negative Note 1) This circuits are for the specifications with up to 8 stations of
common can be used. 2-position double, 3-position and 4-position dual 3 port valve.
There should be wired in order 20→18→16→14 without
skipping or leaving any connectors remaining.
Note 2) For details on PC wiring system, refer to the WEB catalog or
the Best Pneumatics No. 1.
96
Series SY3000/5000/7000
Flat Ribbon Cable Assembly
10 1
AXT100-FC 20 - 2
26 3
1
26
25
(15.6)
L
Specified Layout
COM. COM.
26 25
24 23 COM. COM.
22 21
20 19 20 19 20 19
18 17 18 17 18 17
16 15 16 15 16 15
14 13 14 13 COM. COM. 14 13
12 11 12 11 12 11
10 9 10 9 10 9
10 9
8 7 8 7 8 7
8 7
6 5 6 5 6 5
6 5
4 3 4 3 4 3
4 3
2 1 2 1 2 1
2 1
COM. COM.
(P: 26 pins) (PG: 20 pins) (PH: 10 pins) (J,G: 20 pins PC wiring)
Mixed wiring of single and double wiring can be specified on the manifold specification. The maximum number of stations is determined according to the number of solenoids. The
total number of solenoids should be 24 or less for P, 18 or less for PG, 8 or less for PH, and 16 or less for J/G. 1 solenoid is required for 2-position single, and 2 solenoids for
2-position double, 3-position and 4-position.
97
98
One-touch Fittings/ Type 10, 11, 12 Type 50, 51, 52
Manifold Options Plug-in Connector Connecting Base Plug-in Metal Base Plug-in Sub-plate Valve
Plug Assembly Part No. Manifold Exploded View Manifold Exploded View
Type 10 Plug-in Connector Connecting Base
Side Ported RoHS
Terminal Block Box
Series SY3000/5000/7000
Type 11
Bottom Ported
99
Plug-in Connector Connecting Base Series SY3000/5000/7000
Valve
A, B port size (Metric/One-touch fitting) A, B port size (Inch/One-touch fitting)
Sub-plate
Type 10/Side ported Type 11/Bottom ported Type 10/Side ported Type 11/Bottom ported
Symbol A, B port Symbol A, B port
SY3000 SY5000 SY7000 SY5000 SY7000 SY3000 SY5000 SY7000 SY5000 SY7000
C2 ø2 — — — — N1 ø1/8" — — — —
Plug-in
C3 ø3.2 — — — — N3 ø5/32" — —
Straight
C4 ø4 — — N7 ø1/4"
Straight
C6 ø6 N9 ø5/16" —
C8 ø8 — N11 ø3/8" — — —
C10 ø10 — — — CM∗ Straight port, mixed sizes
C12 ø12 — — — LN3 ø5/32" — — — —
CM∗
Upward
Straight port, mixed sizes LN7 ø1/4" — — —
Metal Base
L4 ø4 — — — LN9 ø5/16" — — — —
L6 ø6 — — LN11 ø3/8" — — — —
Upward
Elbow Note)
L8 ø8 — — — BN3 ø5/32" — — — —
Downward
L10 ø10 — — — — BN7 ø1/4" — — —
Plug-in
L12 ø12 — — — — BN9 ø5/16" — — — —
Elbow Note)
B4 ø4 — — — BN11 ø3/8" — — — —
Downward
P, E port size
ø8 ø10 ø12 ø10 ø12
(One-touch fittings)
Note) To avoid interference with the body or piping, select downward elbow port when mounting the optional spacer assembly (pages 226 to 228).
∗ Indicate the sizes on the manifold specification sheet in the case of “CM”, “LM”.
Plug-in
Manifold Exploded View
Type 10, 11, 12
Plug Assembly Part No.
One-touch Fittings/
Manifold Options
Protective class
class III (Mark: )
100
Series SY3000/5000/7000
How to Order Valves (With mounting screw) Refer to page 3 for valve specifications.
SY 3 1 0 0 5 1
Base mounted
Type of actuation
1
2-position
Single Coil type E: F:
2 Double Nil Standard Push-turn Slide locking
3 Closed center T With power saving circuit (Continuous duty type) locking type
4 3-position Exhaust center ∗ Be sure to select the power saving circuit type lever
5 Pressure center when the valve is continuously energized for type
A∗ N.C./N.C. long periods of time.
4-position
B∗ dual 3-port N.O./N.O. ∗ Be careful of the energizing time when the
C∗ N.C./N.O. power saving circuit is selected. Refer to page
∗ Refer to page 14 for with the safety slide locking
244 for details.
∗ Only rubber seal type is available for the manual override.
4-position dual 3-port valve.
Rated voltage
5 24 VDC Type of mounting screw
Seal type 6 12 VDC
Nil Round head combination screw
0 Rubber seal B Hexagon socket head cap screw
1 Metal seal Round head combination screw
K (Falling-out-prevention type)
Light/surge voltage suppressor
and common specification Hexagon socket head cap screw
H (Falling-out-prevention type)
Pilot type Symbol With light
Surge voltage Common
Nil Internal pilot suppressor specification ∗ For “K” and “H”, the valve body cover has a drop
R External pilot Nil — — prevention construction to stop the mounting screws
R — Non-polar from falling out when the valve is removed for
U maintenance etc.
∗ When ordering a valve individually, the base gasket is
S — Positive
Back pressure check valve (Built-in valve type) Z
common
not included. Since the base gasket is attached to the
manifold, please order the base gasket separately if it
Nil None NS — Negative is needed for maintenance service.
H Built-in NZ common Refer to page 220 for part numbers of the base
∗ Only rubber seal type. Manifold installed type is ∗ Only “Z” and “NZ” types are available for with the gasket and mounting screw.
available if the back pressure check valve is power saving circuit. ∗ "B" and "H" cannot be selected for the individual
required for a valve with metal seal. Refer to SUP/EXH spacer assembly, interface regulator or
page 232 for Ordering Example. However, it is double check spacer assembly with residual pressure
not recommended to use the built-in valve type release valve.
and the manifold installed type at the same time
because it will reduce the flow.
∗ The built-in valve type back pressure check
valve is not available for the 3-position type and
the SY7000.
Protective class
class III (Mark: )
101
Plug-in Connector Connecting Base Series SY3000/5000/7000
Valve
Plug-in Type 10/Side Ported
C2
U
C4, N3 (D)
SS5Y3-10T- Stations D - C3, N1
Sub-plate
B C6, N7
D side U side
Plug-in
(L5) L1
Manual override Note 2)
( )
DIN rail holding screw Push-turn locking slotted type:
DIN rail holding screw
(For DIN rail mounting) Press, then rotate it.
(For DIN rail mounting)
(8)
DIN rail 4(A) port side : Blue (For rubber seal)
(Light/surge : Gray (For metal seal)
voltage suppressor) 2(B) port side : Yellow
D side
U side
Metal Base
(5.5)
(8)
B A B A B A B A B A
(35)
14 A 14 A 14 A 14 A 14 A
126
83
92.6
Plug-in
80
60.5
(40.9)
12 B 12 B 12 B 12 B 12 B
4.6
20.4
4.6
1.7
16
(5.3) (L4)
(DIN rail mounting hole pitch: 12.5)
(L3)
1 P 1 P
Plug-in
77.7
63.1
13.6
10.6
56.6
45.5
3/5 E 2 B2 B2 B2 B2 B 3/5 E
40.2
4 A4 A4 A4 A4 A
21.6
18
mounting)
34.9
(11.8)
(Pitch)
107.1 15.5 P = 10.5 (17.8)
n: Stations 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
L1 164.3 174.8 185.3 195.8 206.3 216.8 227.3 237.8 248.3 258.8 269.3 279.8 290.3 300.8 311.3 321.8 332.3 342.8 353.3
Manifold Options
L2 63 73.5 84 94.5 105 115.5 126 136.5 147 157.5 168 178.5 189 199.5 210 220.5 231 241.5 252
L3 198 198 210.5 223 235.5 248 260.5 273 273 285.5 298 310.5 323 335.5 335.5 348 360.5 373 385.5
L4 187.5 187.5 200 212.5 225 237.5 250 262.5 262.5 275 287.5 300 312.5 325 325 337.5 350 362.5 375
L5 17 11.5 12.5 13.5 14.5 15.5 16.5 17.5 12.5 13.5 14.5 15.5 16.5 17.5 12 13 14 15 16
102
Series SY3000/5000/7000
U C4, N3
SS5Y5-10T- Stations D - C6, N7 (D)
B C8, N9
D side U side
U side
(5.5)
(8)
BA BA BA BA BA
(35)
14 A 14 A 14 A 14 A 14 A
126.4
97.5
113.4
80
81.2
(61.7)
5.5
12 B 12 B 12 B 12 B 12 B
16.4
10.9
1
4.7
(5.9)
(8.3)
2 x M5 mounting hole
4 x M5 mounting hole
7.1 87.7 L2 1.5
(Fitting for the type with P/E
(5.3) (L4) ports on the U and/or D sides)
(DIN rail mounting hole pitch: 12.5)
(L3)
One-touch fitting
[1(P), 3/5(E) port] One-touch fitting
Applicable tube O.D.: ø10, ø3/8" [4(A), 2(B) port]
(Station 1) ----------- (Station n) Applicable tube O.D.: ø4, ø5/32"
2 x G3/4
: ø6, ø1/4"
Conduit port : ø8, ø5/16"
1 P 1 P
77.7
14.1
73.2
8.7
2 B2 B2 B2 B2 B
56.6
45.5
3/5 E 3/5 E
33.4
29.1
4 A4 A4 A4 A4 A
13.2
12.4
mounting)
34.9
(11.8)
(Pitch)
108.8 18 P = 16 (20.5)
n: Stations 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
L1 181.3 197.3 213.3 229.3 245.3 261.3 277.3 293.3 309.3 325.3 341.3 357.3 373.3 389.3 405.3 421.3 437.3 453.3 469.3
L2 80 96 112 128 144 160 176 192 208 224 240 256 272 288 304 320 336 352 368
L3 210.5 223 248 260.5 273 285.5 310.5 323 335.5 360.5 373 385.5 398 423 435.5 448 460.5 485.5 498
L4 200 212.5 237.5 250 262.5 275 300 312.5 325 350 362.5 375 387.5 412.5 425 437.5 450 475 487.5
L5 14.5 13 17.5 15.5 14 12 16.5 15 13 17.5 16 14 12.5 17 15 13.5 11.5 16 14.5
103
Plug-in Connector Connecting Base Series SY3000/5000/7000
Valve
Plug-in Type 10/Side Ported
C6, N7
U
C10, N11 (D)
SS5Y7-10T- Stations D - C8, N9
Sub-plate
B C12
D side U side
Plug-in
L1
DIN rail holding screw DIN rail holding screw (
Push-turn locking slotted type:
Press, then rotate it. )
(8)
(For DIN rail mounting) (For DIN rail mounting) 4(A) port side : Blue (For rubber seal)
(Light/surge voltage suppressor) : Gray (For metal seal)
2(B) port side : Yellow
D side
U side
(8)
(DIN rail)
Metal Base
B A B A B A B A B A
(35)
14 A 14 A 14 A 14 A 14 A
141.8
80
128.8
115
(5.5)
96.7
Plug-in
(77.1)
12 B 12 B 12 B 12 B 12 B
5.5
31.8
8.8
3.9
(6)
2 x M5 mounting hole
(A, B port: ø12)
(17.9)
4 x M5 mounting hole
7.1 87.9 L2 1.5
(Fitting for the type with P/E
(5.3) (L4) ports on the U and/or D sides)
(DIN rail mounting hole pitch: 12.5)
(L3)
Plug-in
1 P 1 P
82.7
77.7
2 B2 B2 B2 B2 B
56.6
45.5
3/5 E 3/5 E
11.1
8.7
35.2
31.6
4 A4 A4 A4 A4 A
113.8 20.5 P = 19
n: Stations 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
Manifold Options
L1 195.5 214.5 233.5 252.5 271.5 290.5 309.5 328.5 347.5 366.5 385.5 404.5 423.5 442.5 461.5 480.5 499.5 518.5 537.5
L2 94 113 132 151 170 189 208 227 246 265 284 303 322 341 360 379 398 417 436
L3 223 248 260.5 285.5 298 323 335.5 360.5 373 398 410.5 435.5 448 473 485.5 510.5 523 548 573
L4 212.5 237.5 250 275 287.5 312.5 325 350 362.5 387.5 400 425 437.5 462.5 475 500 512.5 537.5 562.5
L5 14 17 13.5 16.5 13.5 16.5 13 16 13 16 12.5 15.5 12.5 15.5 12 15 12 15 18
104
Plug-in Connector Connecting Base
Type 12 RoHS
Top Ported Terminal Block Box
Series SY3000/5000/7000
How to Order Manifold
SS5Y 3 12T 05 U
Refer to pages 186 to 188 for
dimensions of Type 12/Top ported type.
Series Valve stations SUP/EXH block assembly
3 SY3000 Symbol Stations Note Nil Internal pilot
5 SY5000 02 2 stations S Internal pilot, Built-in silencer
7 SY7000 Double wiring Note 1) R External pilot
10 10 stations ∗ For built-in silencer type, P and E ports are
02 2 stations available on U and D sides. 3/5(E) port is
Specified layout Note 2)
P, E port entry (Available up to 20 solenoids)
plugged. The silencer exhaust port is located on
20 20 stations the opposite side of P, E port entry. (Example:
U Note) U side (2 to 10 stations) When the P, E port entry is D side, the silencer
D Note) D side (2 to 10 stations) Note 1) Double wiring: 2-position single, double, exhaust port is U side.)
3-position and 4-position valves can be ∗ When the built-in silencer type is used, keep the
B Both sides (2 to 20 stations)
used on all manifold stations. exhaust port from coming in direct contact with
Note) For type “S”, supply/exhaust block assembly Use of a 2-position single solenoid will result
with built-in silencer, choose U or D for P port water or other liquids.
in an unused control signal. If this is not
entry. desired, order with a specified layout.
Note 2) Specified layout: Indicate the wiring
specifications on the manifold specification
sheet. (Note that 2-position double,
3-position and 4-position valves cannot be P, E port size
used where single wiring has been (One-touch fittings)
specified.)
Note 3) This also includes the number of blanking
Symbol SY3000 SY5000 SY7000
plate assembly. Nil ø8 ø10 ø12
N ø5/16" ø3/8" ø1/2"
∗ For N, sizes are in inches.
How to Order Manifold Assembly
Example (SS5Y3-12T-)
2-position double (24 VDC)
Mounting
SY3230-5U1-C6 (1 set) Nil Direct mounting
2-position single (24 VDC) 3-position closed DIN rail mounting
SY3130-5U1-C6 (3 sets) center (24 VDC) D
(With DIN rail)
SY3330-5U1-C6 (1 set) DIN rail mounting
D0
(Without DIN rail)
D3 For 3 stations Specify a longer rail than
the standard length.
D20 For 20 stations
Note) Refer to page 247 for the fixation of DIN rail
ide
Us mounting type manifold.
s
n
tio
ta
S
3
2
ide
1
Ds
Manifold base
(5 stations)
SS5Y3-12T-05D
SS5Y3-12T-05D ············1 set (Type 12 5-station manifold base part no.)
∗SY3130-5U1-C6 ············3 sets (2-position single part no.)
∗SY3230-5U1-C6 ············1 set (2-position double part no.)
∗SY3330-5U1-C6 ············1 set (3-position closed center part no.)
The asterisk denotes the symbol for assembly.
Prefix it to the part numbers of the valve etc.
• The valve arrangement is numbered as the 1st station from the D side.
• Under the manifold part number, state the valves to be mounted in order
from the 1st station as shown in the figure above. If the arrangement
becomes complicated, specify on a manifold specification sheet.
105
Plug-in Connector Connecting Base Series SY3000/5000/7000
Valve
How to Order Valves (With mounting screw) Refer to page 3 for valve specifications.
SY 3 1 3 0 5 1 C6
Sub-plate
Plug-in
Top ported
Metal Base
pressure type. 02
Type of actuation 1/4 SY7000
Plug-in
4 3-position Exhaust center T With power saving circuit (Continuous duty type) C3 ø3.2 — —
5 Pressure center ∗ Be sure to select the power saving circuit type C4 ø4 —
A∗ N.C./N.C. when the valve is continuously energized for C6 ø6
4-position
B∗ dual 3-port
N.O./N.O. long periods of time. C8 ø8 —
C∗ N.C./N.O. ∗ Be careful of the energizing time when the C10 ø10 — —
power saving circuit is selected. Refer to page C12
Plug-in
Nil None NS — Negative
H NZ common
Built-in
∗ Only “Z” and “NZ” types are available for with the
Type of mounting screw
∗ Only rubber seal type. Manifold installed type is
Gasket
m
6m
Electrical entry
2 x G3/4
SOL.a
1B
1A 2A 3A 4A 5A 6A 7A 8A 9A 10A COM
2A
Station 2
2B
SOL.b
(−) number of solenoids should be 20 or less. 1
3A
2B (+)
3B
SOL.a
4A
Station 3 SOL.b
5A
SOL.a
6A 7A
Station 4 SOL.b
4B (−) (+)
7B
8A
SOL.a
8B
5A (−) (+)
9A 10A COM
Station 5 SOL.b
9B 10B
5B (−) (+)
SOL.a
6A (−) (+)
Station 6 SOL.b
6B (−) (+)
1A 2A 3A 4A 5A 6A 7A 8A 9A 10A COM
SOL.a
1A 2A 3A 4A 5A 6A 7A 8A 9A 10A COM
1B 2B 3B 4B 5B 6B 7B 8B 9B 10B
7A (−) (+)
Station 7 SOL.b
1B 2B 3B 4B 5B 6B 7B 8B 9B 10B
7B (−) (+)
SOL.a
8A (−) (+)
If alignment is not specified, the Station 8 SOL.b
8B (−) (+)
internal wiring is double wiring SOL.a
9A (−) (+)
(connected to SOL. a and SOL. b) Station 9 SOL.b
regardless of number of stations, 9B (−) (+)
SOL.a
valve and option types. 10A (−) (+)
Station 10 SOL.b
10B (−) (+)
107
108
One-touch Fittings/ Type 10, 11, 12 Type 50, 51, 52
Manifold Options Plug-in Connector Connecting Base Plug-in Metal Base Plug-in Sub-plate Valve
Plug Assembly Part No. Manifold Exploded View Manifold Exploded View
Type 10 Plug-in Connector Connecting Base
Side Ported RoHS
Lead Wire
Type 11
Bottom Ported
Series SY3000/5000/7000
How to Order Manifold
e
s
U sid SUP/EXH block assembly
on
ati Nil Internal pilot
St
3 S Internal pilot, Built-in silencer
2
e
1 R External pilot
D sid
∗ 3/5(E) port is plugged for the built-in silencer type.
Manifold base ∗ When the built-in silencer type is used, keep the exhaust port from coming in
(5 stations) direct contact with water or other liquids.
SS5Y3-10L11-05D-C6
SS5Y3-10L11-05D-C6 ···1 set (Type 10 5-station manifold base part no.)
∗SY3100-5U1 ···················3 sets (2-position single part no.)
∗SY3200-5U1 ···················1 set (2-position double part no.)
∗SY3300-5U1 ···················1 set (3-position closed center part no.)
The asterisk denotes the symbol for assembly.
Prefix it to the part numbers of the valve etc.
• The valve arrangement is numbered as the 1st station from the D side.
• Under the manifold part number, state the valves to be mounted in order from
the 1st station as shown in the figure above. If the arrangement becomes
complicated, specify on a manifold specification sheet.
Note) When mixing top ported configurations, select from page 116.
In this case, use caution as there is also output on the A and B port on base side.
Specify on a manifold specification sheet if plugs are required on the A and B port
on base side.
109
Valve
A, B port size (Metric/One-touch fitting) A, B port size (Inch/One-touch fitting)
Sub-plate
Type 10/Side ported Type 11/Bottom ported Type 10/Side ported Type 11/Bottom ported
Symbol A, B port Symbol A, B port
SY3000 SY5000 SY7000 SY5000 SY7000 SY3000 SY5000 SY7000 SY5000 SY7000
C2 ø2 — — — — N1 ø1/8" — — — —
Plug-in
C3 ø3.2 — — — — N3 ø5/32" — —
Straight
C4 ø4 — — N7 ø1/4"
Straight
C6 ø6 N9 ø5/16" —
C8 ø8 — N11 ø3/8" — — —
C10 ø10 — — — CM∗ Straight port, mixed sizes
C12 ø12 — — — LN3 ø5/32" — — — —
CM∗
Upward
Straight port, mixed sizes LN7 ø1/4" — — —
Metal Base
L4 ø4 — — — LN9 ø5/16" — — — —
L6 ø6 — — LN11 ø3/8" — — — —
Upward
Elbow Note)
L8 ø8 — — — BN3 ø5/32" — — — —
Downward
L10 ø10 — — — — BN7 ø1/4" — — —
Plug-in
L12 ø12 — — — — BN9 ø5/16" — — — —
Elbow Note)
B4 ø4 — — — BN11 ø3/8" — — — —
Downward
P, E port size
ø8 ø10 ø12 ø10 ø12
(One-touch fittings)
Note) To avoid interference with the body or piping, select downward elbow port when mounting the optional spacer assembly (pages 226 to 228).
∗ Indicate the sizes on the manifold specification sheet in the case of “CM”, “LM”.
∗ The direction of P, E port fittings is the same as for A, B port. If selecting “LM”, indicate it on the manifold specification sheet for the P, E port fitting direction.
···
Plug-in
D — — 24 For 24 stations stations.
DIN rail
A mounting
B —
110
Series SY3000/5000/7000
How to Order Valves (With mounting screw) Refer to page 3 for valve specifications.
SY 3 1 0 0 5 1
Base mounted
Type of actuation
1 Single Coil type
2-position E: F:
2 Double Nil Standard Push-turn Slide locking
3 Closed center T With power saving circuit (Continuous duty type) locking type
4 3-position Exhaust center ∗ Be sure to select the power saving circuit type lever
5 Pressure center when the valve is continuously energized for type
A∗ N.C./N.C. long periods of time.
4-position ∗ Be careful of the energizing time when the
B∗ dual 3-port
N.O./N.O.
power saving circuit is selected. Refer to page
C∗ N.C./N.O.
244 for details. ∗ Refer to page 14 for with the safety slide locking
∗ Only rubber seal is available for the 4-position manual override.
dual 3-port valve.
Rated voltage
5 24 VDC Type of mounting screw
Seal type 6 12 VDC
Nil Round head combination screw
0 Rubber seal B Hexagon socket head cap screw
1 Metal seal Round head combination screw
Light/surge voltage suppressor K (Falling-out-prevention type)
and common specification H Hexagon socket head cap screw
(Falling-out-prevention type)
Pilot type Symbol With light
Surge voltage Common
suppressor specification ∗ For “K” and “H”, the valve body cover has a drop
Nil Internal pilot
prevention construction to stop the mounting
Nil — —
R External pilot screws from falling out when the valve is
R — Non-polar
removed for maintenance etc.
U
∗ When ordering a valve individually, the base
S — Positive gasket is not included. Since the base gasket is
Back pressure check valve Z common attached to the manifold, please order the base
(Built-in valve type) NS — Negative gasket separately if it is needed for maintenance
Nil None NZ common service.
Refer to page 220 for part numbers of the base
H Built-in ∗ Only “Z” and “NZ” types are available for with the
power saving circuit. gasket and mounting screw.
∗ Only rubber seal type. Manifold installed type is ∗ "B" and "H" cannot be selected for the individual
available if the back pressure check valve is SUP/EXH spacer assembly, interface regulator
required for a valve with metal seal. Refer to or double check spacer assembly with residual
page 232 for Ordering Example. However, it is pressure release valve.
not recommended to use the built-in valve type
and the manifold installed type at the same time
because it will reduce the flow.
∗ The built-in valve type back pressure check
valve is not available for the 3-position type and
the SY7000.
Protective class
class III (Mark: )
111
Plug-in Connector Connecting Base Series SY3000/5000/7000
Valve
Plug-in Type 10/Side Ported
C2
1 U
SS5Y3-10L 2 - Stations D - C3,
C4, N3 (D)
N1
Sub-plate
3 B C6, N7
D side U side
Manual override Note 2)
(L5) L1
DIN rail holding screw (
Push-turn locking slotted type:
Press, then rotate it. )
Plug-in
(For DIN rail mounting) 4(A) port side : Blue (For rubber seal)
DIN rail (Light/surge : Gray (For metal seal)
2(B) port side : Yellow
voltage suppressor)
(5.5)
(8)
B A B A B A B A B A
(35)
92.6
14 A 14 A 14 A 14 A 14 A
83
Metal Base
67.8
60.5
(40.9)
4.6
12 B 12 B 12 B 12 B 12 B
17
Plug-in
4.6
1.7
)C6: 3.6
N7: 7.4
(4.9)
4 x M4 mounting hole
(
18 (Fitting for the type with P/E
ports on the U and/or D sides)
43 L2 1.5
One-touch fitting
[4(A), 2(B) port]
One-touch fitting
Applicable tube O.D.: ø2
(Station 1) --- (Station n)
63.1
56.6
3/5 E 2 B2 B2 B2 B2 B 3/5 E
40.2
4 A4 A4 A4 A4 A
21.6
18
Plug-in
(For DIN rail
(7.5)
mounting)
(Pitch)
(11.8)
n: Stations 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
L1 112 122.5 133 143.5 154 164.5 175 185.5 196 206.5 217 227.5 238 248.5 259 269.5 280 290.5 301 311.5 322 332.5 343
L2 63 73.5 84 94.5 105 115.5 126 136.5 147 157.5 168 178.5 189 199.5 210 220.5 231 241.5 252 262.5 273 283.5 294
Manifold Options
L3 135.5 148 160.5 173 185.5 198 210.5 210.5 223 235.5 248 260.5 273 273 285.5 298 310.5 323 335.5 335.5 348 360.5 373
L4 125 137.5 150 162.5 175 187.5 200 200 212.5 225 237.5 250 262.5 262.5 275 287.5 300 312.5 325 325 337.5 350 362.5
L5 12 13 14 15 16 17 18 12.5 13.5 14.5 15.5 16.5 17.5 12.5 13.5 14.5 15.5 16.5 17.5 12 13 14 15
112
Series SY3000/5000/7000
1 U C4, N3
SS5Y5-10L 2 - Stations D - C6, N7 (D)
3 B C8, N9
D side U side
Manual override Note 2)
(L5)
DIN rail holding screw
L1
(Push-turn locking slotted type:
Press, then rotate it. )
(For DIN rail mounting) 4(A) port side : Blue (For rubber seal)
DIN rail (Light/surge : Gray (For metal seal)
voltage suppressor) 2(B) port side : Yellow
(5.5)
(8)
BA BA BA BA BA
(35)
14 A 14 A 14 A 14 A 14 A
97.5
113.4
64.4
81.2
(61.7)
5.5
12 B 12 B 12 B 12 B 12 B
24.2
10.9
4.7
(5.9)
(8.3)
4 x M5 mounting hole
18
(Fitting for the type with P/E
18
42.5 L2 1.5
ports on the U and/or D sides)
(Lead wire length)
0.6 m, 1.5 m, 3 m
(5.3) (L4)
(DIN rail mounting hole pitch: 12.5)
(L3)
One-touch fitting
[4(A), 2(B) port]
(Station 1) ----------- (Station n) Applicable tube O.D.: ø4, ø5/32"
: ø6, ø1/4"
One-touch fitting : ø8, ø5/16"
[1(P), 3/5(E) port]
Applicable tube O.D.: ø10, ø3/8"
14.1
1 P 1 P
73.2
2 B2 B2 B2 B2 B
56.6
8.7
3/5 E 3/5 E
33.4
29.1
4 A4 A4 A4 A4 A
12.4
(Pitch)
mounting)
(11.8)
56.5 18 P = 16 (20.5)
n: Stations 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
L1 129 145 161 177 193 209 225 241 257 273 289 305 321 337 353 369 385 401 417 433 449 465 481
L2 80 96 112 128 144 160 176 192 208 224 240 256 272 288 304 320 336 352 368 384 400 416 432
L3 160.5 173 185.5 210.5 223 235.5 260.5 273 285.5 298 323 335.5 348 360.5 385.5 398 410.5 435.5 448 460.5 473 498 510.5
L4 150 162.5 175 200 212.5 225 250 262.5 275 287.5 312.5 325 337.5 350 375 387.5 400 425 437.5 450 462.5 487.5 500
L5 16 14 12.5 17 15 13.5 18 16 14.5 12.5 17 15.5 13.5 12 16.5 14.5 13 17.5 15.5 14 12 16.5 15
113
Plug-in Connector Connecting Base Series SY3000/5000/7000
Valve
Plug-in Type 10/Side Ported
C6, N7
1 U
SS5Y7-10L 2 - Stations D - C8,
C10, N11 (D)
N9
Sub-plate
3 B C12
D side U side
Plug-in
(L5) L1
DIN rail holding screw (
Push-turn locking slotted type:
Press, then rotate it. )
(For DIN rail mounting) 4(A) port side: Blue (For rubber seal)
(Light/surge voltage suppressor) : Gray (For metal seal)
2(B) port side: Yellow
Metal Base
B A B A B A B A B A
(35)
14 A 14 A 14 A 14 A 14 A
64.4
128.8
115
(5.5)
96.7
Plug-in
(77.1)
12 B 12 B 12 B 12 B 12 B
5.5
39.6
(Lead wire length)
0.6 m, 1.5 m, 3 m
4 x M5 mounting hole
42.7 L2 1.5
(Fitting for the type with P/E
18 (5.3) (L4) ports on the U and/or D sides)
(DIN rail mounting hole pitch: 12.5)
(L3)
One-touch fitting
[1(P), 3/5(E) port] 2
Applicable tube O.D.: ø12, ø1/2"
1 P 1 P
82.7
2 B2 B2 B2 B2 B
56.6
3/5 E 3/5 E
11.1
Plug-in
8.7
35.2
31.6
4 A4 A4 A4 A4 A
14.2
(21.7)
(10)
mounting)
61.5 20.5 P = 19
One-touch fitting
(14.3)
Note 2) Refer to page 183 for dimensions of external pilot, silencer, elbow fittings and slide locking manual override.
Note 3) Refer to page 188 for dimensions of A or B port top-ported type.
n: Stations 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
L1 143.2 162.2 181.2 200.2 219.2 238.2 257.2 276.2 295.2 314.2 333.2 352.2 371.2 390.2 409.2 428.2 447.2 466.2 485.2 504.2 523.2 542.2 561.2
Manifold Options
L2 94 113 132 151 170 189 208 227 246 265 284 303 322 341 360 379 398 417 436 455 474 493 512
L3 173 185.5 210.5 235.5 248 273 285.5 310.5 323 348 360.5 385.5 398 423 435.5 460.5 473 498 510.5 535.5 548 573 585.5
L4 162.5 175 200 225 237.5 262.5 275 300 312.5 337.5 350 375 387.5 412.5 425 450 462.5 487.5 500 525 537.5 562.5 575
L5 15 11.5 14.5 17.5 14.5 17.5 14 17 14 17 13.5 16.5 13.5 16.5 13 16 13 16 12.5 15.5 12.5 15.5 12
114
Plug-in Connector Connecting Base
Type 12 Lead Wire
Top Ported
Series SY3000/5000/7000
RoHS
How to Order Manifold
SS5Y 3 12 L1 1 05 U
Refer to pages 186 to 188 for
dimensions of Type 12/Top
ported type.
1
2
3
P, E port size (One-touch fittings)
e
D sid Symbol SY3000 SY5000 SY7000
Manifold base
(5 stations) Nil ø8 ø10 ø12
SS5Y3-12L11-05D
N ø5/16" ø3/8" ø1/2"
∗ For N, sizes are in inches.
SS5Y3-12L11-05D ···1 set (Type 12 5-station manifold base part no.)
∗SY3130-5U1-C6 ·······3 sets (2-position single part no.)
∗SY3230-5U1-C6 ·······1 set (2-position double part no.) Mounting
∗SY3330-5U1-C6 ·······1 set (3-position closed center part no.) Nil Direct mounting
The asterisk denotes the symbol for assembly. D DIN rail mounting (With DIN rail)
Prefix it to the part numbers of the valve etc. D0 DIN rail mounting (Without DIN rail)
• The valve arrangement is numbered as the 1st station from the D side. D3 For 3 stations
Specify a longer rail than
···
···
• Under the manifold part number, state the valves to be mounted in order the standard length.
from the 1st station as shown in the figure above. If the arrangement D24 For 24 stations
becomes complicated, specify on a manifold specification sheet. Note) Refer to page 247 for the fixation of DIN rail mounting type manifold.
115
Plug-in Connector Connecting Base Series SY3000/5000/7000
Valve
How to Order Valves (With mounting screw) Refer to page 3 for valve specifications.
SY 3 1 3 0 5 1 C6
Sub-plate
Plug-in
Top ported
Metal Base
pressure type. 02 1/4 SY7000
Type of actuation One-touch fitting (Metric)
1 Single Coil type Symbol A, B port SY3000 SY5000 SY7000
2-position C2 ø2 — —
2 Double Nil Standard
Plug-in
3 Closed center T With power saving circuit (Continuous duty type) C3 ø3.2 — —
4 3-position Exhaust center ∗ Be sure to select the power saving circuit type C4 ø4 —
5 Pressure center when the valve is continuously energized for C6 ø6
A∗ N.C./N.C. long periods of time. C8 ø8 —
4-position ∗ Be careful of the energizing time when the
B∗ dual 3-port
N.O./N.O. C10 ø10 — —
power saving circuit is selected. Refer to page
C∗
Plug-in
(Built-in valve type) NZ common
Nil None ∗ Only “Z” and “NZ” types are available for with the Type of mounting screw
H Built-in power saving circuit.
Specified Layout
Mixed wiring of single and double wiring can be specified on the manifold
specification. The maximum number of stations is determined according
to the number of solenoids. The total number of solenoids should be 32
or less. 1 solenoid is required for 2-position single, and 2 solenoids for
2-position double, 3-position and 4-position.
117
Plug-in Connector Connecting Base Series SY3000/5000/7000
Valve
Electrical Wiring Specifications
Lead wire Electrical characteristics
Sub-plate
Item Property
Conductor resistance
Lead wire 143 or less
17 cores 9 cores Lead wire Ω/km, 68°F (20°C)
0.18 mm2 x 17 cores 0.18 mm2 x 9 cores
Voltage limit
2000
V, 1 minute, AC
Plug-in
1
17 2
1
16 13 8 9 3 9 2 Insulation resistance
10 or more
15 12 10 4
8 5 3 MΩ/km, 68°F (20°C)
11 7 4
14 5 6
7 6 Note) Cannot be used for movable wiring. Note) Cannot be used for movable wiring.
The minimum bending radius of the cable The minimum bending radius of the cable
is 45 mm. is 40 mm.
Sheath O.D. Sheath O.D.
Lead Printed mark Lead Printed mark
ø6.8 ø6.3
wire (Both sides) wire (Both sides)
Lead wire no. Polarity
Metal Base
Lead wire no. Polarity color Type Color color Type Color
SOL.a SOL.a
1 (−) (+) Red 1 (−) (+) Red
Station 1 SOL.b Orange Station 1 SOL.b Orange
2 (−) (+) Black 2 (−) (+) Black
SOL.a SOL.a
3 (−) (+) Light Red 3 (−) (+) Light Red
Station 2 SOL.b Station 2 SOL.b
4 (−) (+) gray 4 (−) (+) gray Black
Plug-in
Black
SOL.a SOL.a
5 (−) (+) Red 5 (−) (+) Red
Station 3 SOL.b White Station 3 SOL.b White
6 (−) (+) Black 6 (−) (+) Black
SOL.a SOL.a
7 (−) (+) Red 7 (−) (+) Red
Station 4 SOL.b Yellow Station 4 SOL.b Yellow
8 (−) (+) Black 8 (−) (+) Black
SOL.a COM.
9 (−) (+) Red 9 (+) (−) Pink Red
Plug-in
Manifold Exploded View
Type 10, 11, 12
Plug Assembly Part No.
One-touch Fittings/
Manifold Options
118
Type 10 Plug-in Connector Connecting Base
Side Ported
Circular Connector
Series SY3000/5000/7000
Type 11
Bottom Ported
RoHS
How to Order Manifold
···
12 12 stations
02 2 stations
Type Specified layout Note 2) SUP/EXH block assembly
···
···
(Available up to 24 solenoids)
10 Side ported 24 24 stations Nil Internal pilot
11 Bottom ported∗ Note 1) Double wiring: 2-position single, double, 3-position and S Internal pilot, Built-in silencer
∗ The SY5000 manifold base is 4-position valves can be used on all manifold stations. R External pilot
used for the bottom ported of the Use of a 2-position single solenoid will result in an ∗ 3/5(E) port is plugged for the built-in silencer type.
SY3000. When ordering, refer to unused control signal. If this is not desired, order with a ∗ When the built-in silencer type is used, keep the
“Plug-in Mixed Mounting Type specified layout. exhaust port from coming in direct contact with
Manifold” (from page 189). Note 2) Specified layout: Indicate the wiring specifications on the water or other liquids.
manifold specification sheet. (Note that 2-position
double, 3-position and 4-position valves cannot be used
where single wiring has been specified.)
Note 3) This also includes the number of blanking plate
Refer to the page on the right for .
assembly.
···
119
Valve
A, B port size (Metric/One-touch fitting) A, B port size (Inch/One-touch fitting)
Sub-plate
Type 10/Side ported Type 11/Bottom ported Type 10/Side ported Type 11/Bottom ported
Symbol A, B port Symbol A, B port
SY3000 SY5000 SY7000 SY5000 SY7000 SY3000 SY5000 SY7000 SY5000 SY7000
C2 ø2 — — — — N1 ø1/8" — — — —
Plug-in
C3 ø3.2 — — — — N3 ø5/32" — —
Straight
C4 ø4 — — N7 ø1/4"
Straight
C6 ø6 N9 ø5/16" —
C8 ø8 — N11 ø3/8" — — —
C10 ø10 — — — CM∗ Straight port, mixed sizes
C12 ø12 — — — LN3 ø5/32" — — — —
CM∗
Upward
Straight port, mixed sizes LN7 ø1/4" — — —
Metal Base
L4 ø4 — — — LN9 ø5/16" — — — —
L6 ø6 — — LN11 ø3/8" — — — —
Upward
Elbow Note)
L8 ø8 — — — BN3 ø5/32" — — — —
Downward
L10 ø10 — — — — BN7 ø1/4" — — —
Plug-in
L12 ø12 — — — — BN9 ø5/16" — — — —
Elbow Note)
B4 ø4 — — — BN11 ø3/8" — — — —
Downward
P, E port size
ø8 ø10 ø12 ø10 ø12
(One-touch fittings)
Note) To avoid interference with the body or piping, select downward elbow port when mounting the optional spacer assembly (pages 226 to 228).
∗ Indicate the sizes on the manifold specification sheet in the case of “CM”, “LM”.
Plug-in
Manifold Exploded View
Type 10, 11, 12
Plug Assembly Part No.
One-touch Fittings/
Manifold Options
Protective class
class III (Mark: )
120
Series SY3000/5000/7000
How to Order Valves (With mounting screw) Refer to page 3 for valve specifications.
SY 3 1 0 0 5 1
Base mounted
Type of actuation
1 Single Coil type
2-position E: F:
2 Double Nil Standard Push-turn Slide locking
3 Closed center T With power saving circuit (Continuous duty type) locking type
4 3-position Exhaust center ∗ Be sure to select the power saving circuit type lever
5 Pressure center when the valve is continuously energized for type
A∗ N.C./N.C. long periods of time.
4-position ∗ Be careful of the energizing time when the
B∗ dual 3-port
N.O./N.O.
power saving circuit is selected. Refer to page
C∗ N.C./N.O.
244 for details. ∗ Refer to page 14 for with the safety slide locking
∗ Only rubber seal type is available for the 4-position manual override.
dual 3-port valve. Rated voltage
5 24 VDC
6 12 VDC Type of mounting screw
Seal type Nil Round head combination screw
0 Rubber seal B Hexagon socket head cap screw
1 Metal seal
Light/surge voltage suppressor Round head combination screw
K (Falling-out-prevention type)
and common specification
Hexagon socket head cap screw
Symbol With light
Surge voltage Common H (Falling-out-prevention type)
Pilot type suppressor specification
Nil — — ∗ For “K” and “H”, the valve body cover has a drop
Nil Internal pilot prevention construction to stop the mounting
R External pilot R — Non-polar
screws from falling out when the valve is
U removed for maintenance etc.
S — Positive ∗ When ordering a valve individually, the base
common
Z gasket is not included. Since the base gasket is
Back pressure check valve NS — Negative attached to the manifold, please order the base
(Built-in valve type) NZ common gasket separately if it is needed for maintenance
service.
Nil None ∗ Only “Z” and “NZ” types are available for with the Refer to page 220 for part numbers of the base
H Built-in power saving circuit. gasket and mounting screw.
∗ Only rubber seal type. Manifold installed type is ∗ "B" and "H" cannot be selected for the individual
available if the back pressure check valve is SUP/EXH spacer assembly, interface regulator
required for a valve with metal seal. Refer to or double check spacer assembly with residual
page 232 for Ordering Example. However, it is pressure release valve.
not recommended to use the built-in valve type
and the manifold installed type at the same time
because it will reduce the flow.
∗ The built-in valve type back pressure check
valve is not available for the 3-position type and
the SY7000.
Protective class
class III (Mark: )
121
Plug-in Connector Connecting Base Series SY3000/5000/7000
Valve
Plug-in Type 10/Side Ported
C2
U
C4, N3 (D)
SS5Y3-10M- Stations D - C3, N1
Sub-plate
B C6, N7
D side U side
(L5) L1 Manual override Note 2)
Plug-in
Press, then rotate it.
(For DIN rail mounting) 4(A) port side : Blue (For rubber seal)
DIN rail (Light/surge : Gray (For metal seal)
voltage suppressor) 2(B) port side : Yellow
(5.5)
(8)
B A B A B A B A B A
(35)
92.6
14 A 14 A 14 A 14 A 14 A
Metal Base
83
67.8
60.5
(40.9)
4.6
12 B 12 B 12 B 12 B 12 B
Plug-in
21.9
1.7
4.6
)
(4.9)
C6: 3.6
N7: 7.4
4 x M4 mounting hole
18
18 ( (Fitting for the type with P/E ports on the U and/or D sides)
43 L2 1.5
One-touch fitting
One-touch fitting [4(A), 2(B) port]
[1(P), 3/5(E) port] (Station 1) --- (Station n) Applicable tube O.D.: ø2
Applicable tube O.D.: ø8, ø5/16" : ø3.2, ø1/8"
: ø4, ø5/32"
56.6
AXT100-MC26-050: 5 m 3/5 E 2 B2 B2 B2 B2 B 3/5 E
40.2
4 A4 A4 A4 A4 A
21.6
18
mounting)
(Pitch)
(11.8)
Plug-in
made by CONINVERS GmbH 54.8 15.5 (17.8)
P = 10.5
n: Stations 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
Manifold Options
L1 112 122.5 133 143.5 154 164.5 175 185.5 196 206.5 217 227.5 238 248.5 259 269.5 280 290.5 301 311.5 322 332.5 343
L2 63 73.5 84 94.5 105 115.5 126 136.5 147 157.5 168 178.5 189 199.5 210 220.5 231 241.5 252 262.5 273 283.5 294
L3 135.5 148 160.5 173 185.5 198 210.5 210.5 223 235.5 248 260.5 273 273 285.5 298 310.5 323 335.5 335.5 348 360.5 373
L4 125 137.5 150 162.5 175 187.5 200 200 212.5 225 237.5 250 262.5 262.5 275 287.5 300 312.5 325 325 337.5 350 362.5
L5 12 13 14 15 16 17 18 12.5 13.5 14.5 15.5 16.5 17.5 12.5 13.5 14.5 15.5 16.5 17.5 12 13 14 15
122
Series SY3000/5000/7000
U C4, N3
SS5Y5-10M- Stations D - C6, N7 (D)
B C8, N9 D side U side
Manual override Note 2)
(L5)
DIN rail holding screw
L1
(
Push-turn locking slotted type:
Press, then rotate it. )
(For DIN rail mounting) 4(A) port side : Blue (For rubber seal)
DIN rail (Light/surge voltage suppressor) : Gray (For metal seal)
2(B) port side : Yellow
(5.5)
(8)
BA BA BA BA BA
(35)
14 A 14 A 14 A 14 A 14 A
97.5
113.4
64.4
81.2
61.7
5.5
12 B 12 B 12 B 12 B 12 B
24.2
10.9
4.7
18
(5.9)
(8.3)
18 4 x M5 mounting hole
42.5 L2 1.5 (Fitting for the type with P/E
ports on the U and/or D sides)
(5.3) (L4)
(DIN rail mounting hole pitch: 12.5)
Circular connector cable assembly (L3)
AXT100-MC26-015: 1.5 m
AXT100-MC26-030: 3 m
AXT100-MC26-050: 5 m
One-touch fitting
[4(A), 2(B) port]
Applicable tube O.D.: ø4, ø5/32"
(Station 1)----------- (Station n)
: ø6, ø1/4"
One-touch fitting : ø8, ø5/16"
[1(P), 3/5(E) port]
Applicable tube O.D.: ø10, ø3/8"
1 P 1 P
14.1
73.2
2 B2 B2 B2 B2 B
56.6
12.4
8.7
3/5 E 3/5 E
33.4
29.1
4 A4 A4 A4 A4 A
(For DIN rail
mounting)
(7.5)
n: Stations 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
L1 129 145 161 177 193 209 225 241 257 273 289 305 321 337 353 369 385 401 417 433 449 465 481
L2 80 96 112 128 144 160 176 192 208 224 240 256 272 288 304 320 336 352 368 384 400 416 432
L3 160.5 173 185.5 210.5 223 235.5 260.5 273 285.5 298 323 335.5 348 360.5 385.5 398 410.5 435.5 448 460.5 473 498 510.5
L4 150 162.5 175 200 212.5 225 250 262.5 275 287.5 312.5 325 337.5 350 375 387.5 400 425 437.5 450 462.5 487.5 500
L5 16 14 12.5 17 15 13.5 18 16 14.5 12.5 17 15.5 13.5 12 16.5 14.5 13 17.5 15.5 14 12 16.5 15
123
Plug-in Connector Connecting Base Series SY3000/5000/7000
Valve
Plug-in Type 10/Side Ported
C6, N7
U
C10, N11 (D)
SS5Y7-10M- Stations D - C8, N9
Sub-plate
B C12
D side U side
Plug-in
(L5) L1
DIN rail holding screw (
Push-turn locking slotted type:
Press, then rotate it. )
(For DIN rail mounting) 4(A) port side: Blue (For rubber seal)
: Gray (For metal seal)
(Light/surge voltage suppressor) 2(B) port side: Yellow
Metal Base
B A B A B A B A B A
(35)
14 A 14 A 14 A 14 A 14 A
64.4
128.8
115
(5.5)
96.7
Plug-in
(77.1)
12 B 12 B 12 B 12 B 12 B
5.5
39.6
18 4 x M5 mounting hole
42.7 L2 1.5 (Fitting for the type with P/E ports
(5.3) (L4) on the U and/or D sides)
(DIN rail mounting hole pitch: 12.5)
(L3)
Plug-in
1 P 1 P
82.7
2 B2 B2 B2 B2 B
56.6
3/5 E 3/5 E
11.1
8.7
35.2
31.6
(Pitch)
(For DIN rail
(21.7)
(10)
61.5 20.5 P = 19
Made by CONINVERS GmbH
(14.3)
Note 2) Refer to page 183 for dimensions of external pilot, silencer, elbow fittings and slide locking manual override.
One-touch Fittings/
n: Stations 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
L1 143.2 162.2 181.2 200.2 219.2 238.2 257.2 276.2 295.2 314.2 333.2 352.2 371.2 390.2 409.2 428.2 447.2 466.2 485.2 504.2 523.2 542.2 561.2
Manifold Options
L2 94 113 132 151 170 189 208 227 246 265 284 303 322 341 360 379 398 417 436 455 474 493 512
L3 173 185.5 210.5 235.5 248 273 285.5 310.5 323 348 360.5 385.5 398 423 435.5 460.5 473 498 510.5 535.5 548 573 585.5
L4 162.5 175 200 225 237.5 262.5 275 300 312.5 337.5 350 375 387.5 412.5 425 450 462.5 487.5 500 525 537.5 562.5 575
L5 15 11.5 14.5 17.5 14.5 17.5 14 17 14 17 13.5 16.5 13.5 16.5 13 16 13 16 12.5 15.5 12.5 15.5 12
124
Plug-in Connector Connecting Base
Circular Connector
Type 12
Top Ported
Series SY3000/5000/7000
RoHS
How to Order Manifold
SS5Y 3 12M 05 U
Refer to pages 186 to 188 for
dimensions of Type 12/Top
ported type.
Series Valve stations P, E port entry
3 SY3000 Symbol Stations Note U Note) U side (2 to 10 stations)
5 SY5000 02 2 stations D Note) D side (2 to 10 stations)
7 SY7000 Double wiring Note 1) B Both sides (2 to 24 stations)
···
···
···
(Available up to 24 solenoids)
24 24 stations
Note 1) Double wiring: 2-position single, double,
3-position and 4-position valves can be used
on all manifold stations. SUP/EXH block assembly
Use of a 2-position single solenoid will result
in an unused control signal. If this is not Nil Internal pilot
desired, order with a specified layout. S Internal pilot, Built-in silencer
Note 2) Specified layout: Indicate the wiring R External pilot
specifications on the manifold specification ∗ For built-in silencer type, P and E ports are
sheet. (Note that 2-position double, 3-position available on U and D sides. 3/5(E) port is
and 4-position valves cannot be used where plugged. The silencer exhaust port is located on
single wiring has been specified.) the opposite side of P, E port entry. (Example:
Note 3) This also includes the number of blanking When the P, E port entry is D side, the silencer
plate assembly. exhaust port is U side.)
∗ When the built-in silencer type is used, keep the
exhaust port from coming in direct contact with
How to Order Manifold Assembly water or other liquids.
Example (SS5Y3-12M-)
2-position single (24 VDC)
2-position double (24 VDC)
SY3230-5U1-C6 (1 set)
P, E port size (One-touch fittings)
SY3130-5U1-C6 (3 sets) Symbol SY3000 SY5000 SY7000
3-position closed
center (24 VDC)
Nil ø8 ø10 ø12
SY3330-5U1-C6 (1 set)
N ø5/16" ø3/8" ø1/2"
∗ For N, sizes are in inches.
Us
ide Mounting
s
on Nil Direct mounting
ati
St
3 DIN rail mounting
2 D (With DIN rail)
1
e
sid DIN rail mounting
D D0 (Without DIN rail)
Manifold base (5 stations)
D3 For 3 stations
SS5Y3-12M-05D Specify a longer rail than
···
···
125
Plug-in Connector Connecting Base Series SY3000/5000/7000
Valve
How to Order Valves (With mounting screw) Refer to page 3 for valve specifications.
SY 3 1 3 0 5 1 C6
Sub-plate
Plug-in
Top ported
Metal Base
pressure type. 02 1/4 SY7000
Type of actuation One-touch fitting (Metric)
1 Single Coil type Symbol A, B port SY3000 SY5000 SY7000
2-position C2 ø2 — —
2 Double Nil Standard
Plug-in
3 Closed center T With power saving circuit (Continuous duty type) C3 ø3.2 — —
4 3-position Exhaust center ∗ Be sure to select the power saving circuit type C4 ø4 —
5 Pressure center when the valve is continuously energized for C6 ø6
A∗ N.C./N.C. long periods of time. C8 ø8 —
4-position
B∗ dual 3-port N.O./N.O. ∗ Be careful of the energizing time when the C10 ø10 — —
power saving circuit is selected. Refer to page
C∗ C12
Plug-in
(Built-in valve type) NZ common
Nil None ∗ Only “Z” and “NZ” types are available for with Type of mounting screw
H Built-in the power saving circuit.
126
Series SY3000/5000/7000
L
Station 2 SOL.b
4 (−) (+) 9 Gray Black
SOL.a
5 (−) (+) 10 White Black
Station 3 SOL.b
6 (−) (+) 11 White Red
60
SOL.a
7 (−) (+) 12 Yellow Red
Station 4 SOL.b
8 (−) (+) 13 Orange Red
SOL.a Plug
9 (−) (+) 14 Yellow Black
Station 5 SOL.b
10 (−) (+) 15 Pink Black
SOL.a
11 (−) (+) 16 Blue White
Station 6 SOL.b
12 (−) (+) 17 Purple None
SOL.a
13 (−) (+) 18 Gray None
Station 7 SOL.b
14 (−) (+) 19 Orange Black
SOL.a ø30
15 (−) (+) 20 Red White
Station 8 SOL.b
16 (−) (+) 21 Brown White
SOL.a 15 1
17 (−) (+) 14 16 2 Terminal no. 22 Pink Red
Station 9 SOL.b 24 17
18 (−) (+) 13 3 23 Gray Red
SOL.a 25
19 (−) (+) 23 18
Station 10 12 4 24 Black White
SOL.b
20 (−) (+) 22 26 19 25 White None
SOL.a 11 21 20 5
21 (−) (+) 26 White None
Station 11 SOL.b 10 6
22 (−) (+) M27 female
SOL.a 9 8 7
23 (−) (+) thread
Station 12 SOL.b Electrical characteristics
24 (−) (+) Item Property
COM.
25 (+) (−) Conductor
COM. 65 or
26 (+) (−) resistance
less
Ω/km, 68°F (20°C)
Positive Negative
Voltage limit
common common 1000
V, 1 minute, AC
Circular connector cable assembly
Insulation
Cable Assembly part no. 5 or
resistance
length (L) 26 pins more
MΩ/km, 68°F (20°C)
Note) When using a valve with no polarity, either positive common or 1.5 m AXT100-MC26-015
negative common can be used. Note) The minimum bending
3m AXT100-MC26-030 radius of the circular
5m AXT100-MC26-050 connector cable is 20 mm.
∗ Cannot be used for movable wiring.
∗ Lengths other than the above is also
Specified Layout available. Please contact SMC for details.
Mixed wiring of single and double wiring can be specified on the manifold
specification sheet. The maximum number of stations is determined
according to the number of solenoids. The total number of solenoids
should be 24 or less. 1 solenoid is required for 2-position single, and 2
solenoids for 2-position double, 3-position and 4-position.
127
128
One-touch Fittings/ Type 10, 11, 12 Type 50, 51, 52
Manifold Options Plug-in Connector Connecting Base Plug-in Metal Base Plug-in Sub-plate Valve
Plug Assembly Part No. Manifold Exploded View Manifold Exploded View
Type 10 Plug-in Connector Connecting Base
Side Ported RoHS
EX500
Series SY3000/5000/7000
Type 11
Bottom Ported
···
···
(Positive common) 08 8 stations
DeviceNet™/PROFIBUS DP/ 02 2 stations
Type A2N EtherNet/IP™
Specified layout Note 2)
···
···
(Available up to 16 solenoids)
10 Side ported (Negative common) 16 16 stations
11 Bottom ported∗ Note) Ensure a match with the common Note 1) Double wiring: 2-position single, double,
∗ The SY5000 manifold base is used for the specification of the valve to be used. 3-position and 4-position valves can be
bottom ported of the SY3000. When ordering, used on all manifold stations.
refer to “Plug-in Mixed Mounting Type Manifold” Use of a 2-position single solenoid will
(from page 189). result in an unused control signal. If this is
not desired, order with a specified layout.
Note 2) Specified layout: Indicate the wiring
specifications on the manifold specification
sheet. (Note that 2-position double,
3-position and 4-position valves cannot be
used where single wiring has been
specified.)
Note 3) This also includes the number of blanking
How to Order Manifold Assembly plate assembly.
Note 4) For the product without the SI unit (S0),
note the maximum number of solenoids of
Example (SS5Y3-10SA2-) the SI unit that will be mounted. If the
2-position double (24 VDC) layout is specified, indicate it on the
2-position single (24 VDC) SY3200-5U1 (1 set) manifold specification sheet.
SY3100-5U1 (3 sets)
3-position closed
center (24 VDC)
SY3300-5U1 (1 set)
P, E port entry
U U side (2 to 10 stations)
D D side (2 to 10 stations)
B Both sides (2 to 16 stations)
ide
SUP/EXH block assembly
Us
Nil Internal pilot
s
n
S
tio
3 R External pilot
2
1 ∗ 3/5(E) port is plugged for the built-in silencer
e
D sid type.
∗ When the built-in silencer type is used, keep the
Manifold base (5 stations)
exhaust port from coming in direct contact with
SS5Y3-10SA2-05D-C6 water or other liquids.
SS5Y3-10SA2-05D-C6 ···1 set (Type 10 5-station manifold base part no.)
∗SY3100-5U1 ····················3 sets (2-position single part no.)
∗SY3200-5U1 ····················1 set (2-position double part no.)
∗SY3300-5U1 ····················1 set (3-position closed center part no.)
The asterisk denotes the symbol for assembly.
Prefix it to the part numbers of the valve etc.
• The valve arrangement is numbered as the 1st station from the D side. For details about the EX500 Gateway-type Serial
• Under the manifold part number, state the valves to be mounted in order from Transmission System, refer to the WEB catalog or the Best
the 1st station as shown in the figure above. If the arrangement becomes Pneumatics No. 1 and the Operation Manual. For details about
complicated, specify on a manifold specification sheet. part numbers of SI units to be mounted, refer to page 212 in
Note) When mixing top ported configurations, select from page 136. this catalog. Please download the Operation Manual via SMC
In this case, use caution as there is also output on the A and B port on base side. website, http://www.smcworld.com
Specify on a manifold specification sheet if plugs are required on the A and B port
on base side.
129
Plug-in Connector Connecting Base Series SY3000/5000/7000
Valve
A, B port size (Metric/One-touch fitting) A, B port size (Inch/One-touch fitting)
Sub-plate
Type 10/Side ported Type 11/Bottom ported Type 10/Side ported Type 11/Bottom ported
Symbol A, B port Symbol A, B port
SY3000 SY5000 SY7000 SY5000 SY7000 SY3000 SY5000 SY7000 SY5000 SY7000
C2 ø2 — — — — N1 ø1/8" — — — —
Plug-in
C3 ø3.2 — — — — N3 ø5/32" — —
Straight
C4 ø4 — — N7 ø1/4"
Straight
C6 ø6 N9 ø5/16" —
C8 ø8 — N11 ø3/8" — — —
C10 ø10 — — — CM∗ Straight port, mixed sizes
C12 ø12 — — — LN3 ø5/32" — — — —
CM∗
Upward
Straight port, mixed sizes LN7 ø1/4" — — —
Metal Base
L4 ø4 — — — LN9 ø5/16" — — — —
L6 ø6 — — LN11 ø3/8" — — — —
Upward
Elbow Note)
L8 ø8 — — — BN3 ø5/32" — — — —
Downward
L10 ø10 — — — — BN7 ø1/4" — — —
Plug-in
L12 ø12 — — — — BN9 ø5/16" — — — —
Elbow Note)
B4 ø4 — — — BN11 ø3/8" — — — —
Downward
P, E port size
ø8 ø10 ø12 ø10 ø12
(One-touch fittings)
Note) To avoid interference with the body or piping, select downward elbow port when mounting the optional spacer assembly (pages 226 to 228).
∗ Indicate the sizes on the manifold specification sheet in the case of “CM”, “LM”.
∗ The direction of P, E port fittings is the same as for A, B port. If selecting “LM”, indicate it on the manifold specification sheet for the P, E port fitting direction.
Plug-in
D — —
DIN rail
A mounting
B —
···
(Refer to page 225 for part numbers of DIN rail.) Protective class
class III (Mark: )
130
Series SY3000/5000/7000
How to Order Valves (With mounting screw) Refer to page 3 for valve specifications.
SY 3 1 0 0 5 1
Base mounted
Type of actuation
1 Single Coil type
2-position E: F:
2 Double Nil Standard Push-turn Slide locking
3 Closed center T With power saving circuit (Continuous duty type) locking type
4 3-position Exhaust center ∗ Be sure to select the power saving circuit type lever
5 Pressure center when the valve is continuously energized for type
A∗ N.C./N.C. long periods of time.
4-position ∗ Be careful of the energizing time when the
B∗ dual 3-port N.O./N.O.
power saving circuit is selected. Refer to page
C∗ N.C./N.O.
244 for details. ∗ Refer to page 14 for with the safety slide locking
∗ Only rubber seal type is available for the manual override.
4-position dual 3-port valve.
Rated voltage
5 24 VDC
Seal type Type of mounting screw
Nil Round head combination screw
0 Rubber seal
B Hexagon socket head cap screw
1 Metal seal Light/surge voltage suppressor Round head combination screw
K
and common specification (Falling-out-prevention type)
Surge voltage Common Hexagon socket head cap screw
Symbol With light H
Pilot type suppressor specification (Falling-out-prevention type)
R — ∗ For “K” and “H”, the valve body cover has a drop
Nil Internal pilot Non-polar
U prevention construction to stop the mounting
R External pilot screws from falling out when the valve is
S — Positive
common removed for maintenance etc.
Z
∗ When ordering a valve individually, the base
NS — Negative gasket is not included. Since the base gasket is
Back pressure check valve NZ common attached to the manifold, please order the base
(Built-in valve type) ∗ Only “Z” and “NZ” types are available for with gasket separately if it is needed for maintenance
Nil None the power saving circuit. Select a valve from R, service.
U, S or Z when the SI unit specification is A2 Refer to page 220 for part numbers of the base
H Built-in
(positive common). Select a valve from R, U, NS gasket and mounting screw.
∗ Only rubber seal type. Manifold installed type is or NZ when the SI unit specification is A2N ∗ "B" and "H" cannot be selected for the individual
available if the back pressure check valve is (negative common). SUP/EXH spacer assembly, interface regulator
required for a valve with metal seal. Refer to or double check spacer assembly with residual
page 232 for Ordering Example. However, it is pressure release valve.
not recommended to use the built-in valve type
and the manifold installed type at the same time
because it will reduce the flow.
∗ The built-in valve type back pressure check
valve is not available for the 3-position type and
the SY7000.
Protective class
class III (Mark: )
131
Plug-in Connector Connecting Base Series SY3000/5000/7000
Valve
Plug-in Type 10/Side Ported
C2
U
C4, N3 (D)
SS5Y3-10SA2- Stations D - C3, N1
Sub-plate
B C6, N7
D side U side
Manual override Note 2)
(L5)
( )
Plug-in
L1 Push-turn locking slotted type:
DIN rail holding screw Press, then rotate it.
(For DIN rail mounting) 4(A) port side : Blue (For rubber seal)
: Gray (For metal seal)
(Light/surge voltage suppressor) 2(B) port side : Yellow
SI unit
(5.5)
(8)
Metal Base
B A B A B A B A B A
(35)
92.6
14 A 14 A 14 A 14 A 14 A
83
67.8
60.5
(40.9)
12 B 12 B 12 B 12 B 12 B
Plug-in
4.6
4.6
1.7
)
(4.9)
C6: 3.6
N7: 7.4
12.1
4 x M4 mounting hole
(Fitting for the type with P/E ports on the U and/or D sides)
(
One-touch fitting
One-touch fitting
[1(P), 3/5(E) port]
Applicable tube O.D.: ø8, ø5/16" [4(A), 2(B) port]
Applicable tube O.D.: ø2
1
56.6
60
3/5 E 2 B2 B2 B2 B2 B 3/5 E
43.2
40.2
22.2
21.6
4 A4 A4 A4 A4 A
18
Plug-in
M12
(For DIN rail
(7.5)
mounting)
17.5 (Pitch)
8-pin plug
(11.8)
n: Stations 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
L1 103.5 114 124.5 135 145.5 156 166.5 177 187.5 198 208.5 219 229.5 240 250.5
L2 63 73.5 84 94.5 105 115.5 126 136.5 147 157.5 168 178.5 189 199.5 210
L3 135.5 148 148 160.5 173 185.5 198 210.5 223 223 235.5 248 260.5 273 285.5
Manifold Options
L4 125 137.5 137.5 150 162.5 175 187.5 200 212.5 212.5 225 237.5 250 262.5 275
L5 16 17 12 13 14 15 16 17 18 12.5 13.5 14.5 15.5 16.5 17.5
132
Series SY3000/5000/7000
U C4, N3
SS5Y5-10SA2- Stations D - C6, N7 (D)
B C8, N9
D side U side
Manual override Note 2)
DIN rail
(5.5)
(8)
BA BA BA BA BA
(35)
14 A 14 A 14 A 14 A 14 A
97.5
113.4
79.9
81.2
(61.7)
5.5
12 B 12 B 12 B 12 B 12 B
10.9
8.7
4.7
(5.9)
(8.3)
4 x M5 mounting hole
34 L2 1.5
(Fitting for the type with P/E
(5.3) (L4) ports on the U and/or D sides)
(DIN rail mounting hole pitch: 12.5)
(L3)
One-touch fitting
One-touch fitting [4(A), 2(B) port]
[1(P), 3/5(E) port] Applicable tube O.D.: ø4, ø5/32"
Applicable tube O.D.: ø10, ø3/8" (Station 1) ----------- (Station n) : ø6, ø1/4"
: ø8, ø5/16"
M12
8-pin socket
0
1 P 1 P
14.1
73.2
2 B2 B2 B2 B2 B
1
56.6
60
43.2
3/5 E 3/5 E
33.4
29.1
22.2
4 A4 A4 A4 A4 A
12.4
8.7
17.5
(11.8)
M12 (Pitch)
48 18 P = 16 (20.5)
8-pin plug
n: Stations 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
L1 120.5 136.5 152.5 168.5 184.5 200.5 216.5 232.5 248.5 264.5 280.5 296.5 312.5 328.5 344.5
L2 80 96 112 128 144 160 176 192 208 224 240 256 272 288 304
L3 148 160.5 185.5 198 210.5 235.5 248 260.5 273 298 310.5 323 348 360.5 373
L4 137.5 150 175 187.5 200 225 237.5 250 262.5 287.5 300 312.5 337.5 350 362.5
L5 14 12 16.5 15 13 17.5 16 14 12.5 17 15 13.5 18 16 14.5
133
Plug-in Connector Connecting Base Series SY3000/5000/7000
Valve
Plug-in Type 10/Side Ported
C6, N7
U
C10, N11 (D)
SS5Y7-10SA2- Stations D - C8, N9
Sub-plate
B C12
D side U side
(L5) L1 Manual override Note 2)
Plug-in
DIN rail holding screw (
Push-turn locking slotted type:
Press, then rotate it. )
SI unit (For DIN rail mounting) 4(A) port side : Blue (For rubber seal)
: Gray (For metal seal)
(Light/surge voltage suppressor)
2(B) port side: Yellow
Metal Base
B A B A B A B A B A
(35)
14 A 14 A 14 A 14 A 14 A
128.8
115
79.9
(5.5)
96.7
Plug-in
(77.1)
12 B 12 B 12 B 12 B 12 B
5.5
24.1
0
1 P 1 P
82.7
2 B2 B2 B2 B2 B
Plug-in
1
56.6
60
43.2
3/5 E 3/5 E
11.1
8.7
35.2
31.6
4 A4 A4 A4 A4 A
22.2
(14.3)
M12
mounting)
n: Stations 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
L1 134.7 153.7 172.7 191.7 210.7 229.7 248.7 267.7 286.7 305.7 324.7 343.7 362.7 381.7 400.7
L2 151 170 189 208 227 246 265 284 303 322 341 360
Manifold Options
94 113 132
L3 160.5 185.5 198 223 235.5 260.5 273 298 310.5 335.5 348 373 398 410.5 435.5
L4 150 175 187.5 212.5 225 250 262.5 287.5 300 325 337.5 362.5 387.5 400 425
L5 13 16 12.5 15.5 12.5 15.5 12 15 12 15 11.5 14.5 17.5 14.5 17.5
134
Plug-in Connector Connecting Base
EX500
Series SY3000/5000/7000
Type 12
Top Ported
RoHS
How to Order Manifold
SS5Y 3 12S A2 05 U
Refer to pages 186 to 188 for
dimensions of Type 12/Top
ported type.
Series P, E port entry Valve stations
3 SY3000 U Note) U side (2 to 10 stations) Symbol Stations Note
5 SY5000 D Note) D side (2 to 10 stations) 02 2 stations
7 SY7000 B Both sides (2 to 16 stations) Double wiring Note 1)
···
···
Note) For type “S”, supply/exhaust block 08 8 stations
assembly with built-in silencer, choose U or 02 2 stations
SI unit D for P port entry. Specified layout Note 2)
···
···
(Available up to 16 solenoids)
0 Without SI unit 16 16 stations
DeviceNet™/PROFIBUS DP/ Note 1) Double wiring: 2-position single, double,
A2 EtherNet/IP™ SUP/EXH block assembly 3-position and 4-position valves can be used on
(Positive common) Nil Internal pilot all manifold stations.
DeviceNet™/PROFIBUS DP/ S Internal pilot/Built-in silencer Use of a 2-position single solenoid will result in
A2N EtherNet/IP™ R External pilot an unused control signal. If this is not desired,
(Negative common) order with a specified layout.
∗ For built-in silencer type, P and E ports are Note 2) Specified layout: Indicate the wiring
Note) Ensure a match with the common available on U and D sides. 3/5(E) port is specifications on the manifold specification
specification of the valve to be used. plugged. The silencer exhaust port is located on sheet. (Note that 2-position double, 3-position
the opposite side of P, E port entry. (Example: and 4-position valves cannot be used where
When the P, E port entry is D side, the silencer single wiring has been specified.)
exhaust port is U side.) Note 3) This also includes the number of blanking plate
∗ When the built-in silencer type is used, keep the assembly.
exhaust port from coming in direct contact with Note 4) For the product without the SI unit (S0), note the
water or other liquids. maximum number of solenoids of the SI unit that
will be mounted. If the layout is specified,
How to Order Manifold Assembly indicate it on the manifold specification sheet.
Example (SS5Y3-12SA2-)
2-position double (24 VDC)
SY3230-5U1-C6 (1 set)
P, E port size (One-touch fittings)
2-position single (24 VDC) Symbol SY3000 SY5000 SY7000
SY3130-5U1-C6 (3 sets) 3-position closed
center (24 VDC) Nil ø8 ø10 ø12
SY3330-5U1-C6 (1 set)
N ø5/16" ø3/8" ø1/2"
∗ For N, sizes are in inches.
Mounting
sid
e Nil Direct mounting
U DIN rail mounting
D
s
n
···
135
Plug-in Connector Connecting Base Series SY3000/5000/7000
Valve
How to Order Valves (With mounting screw) Refer to page 3 for valve specifications.
SY 3 1 3 0 5 1 C6
Sub-plate
Plug-in
Top ported
Metal Base
pressure type. 02 1/4 SY7000
Type of actuation Coil type One-touch fitting (Metric)
1 Single Symbol A, B port SY3000 SY5000 SY7000
2-position Nil Standard
2 Double C2 ø2 — —
T With power saving circuit (Continuous duty type)
Plug-in
3 Closed center C3 ø3.2 — —
∗ Be sure to select the power saving circuit type
4 3-position Exhaust center when the valve is continuously energized for
C4 ø4 —
5 Pressure center long periods of time. C6 ø6
A∗ N.C./N.C. ∗ Be careful of the energizing time when the C8 ø8 —
4-position
B∗ dual 3-port N.O./N.O. power saving circuit is selected. Refer to page C10 ø10 — —
C∗ 244 for details. C12
Plug-in
U, S or Z when the SI unit specification is A2
(Built-in valve type) (positive common). Select a valve from R, U, NS
Nil None or NZ when the SI unit specification is A2N Type of mounting screw
H Built-in (negative common).
136
Type 10
Side Ported
Plug-in Connector Connecting Base
RoHS
EX600
Series SY3000/5000/7000
Type 11
Bottom Ported
···
Direct
9 9 stations AA mounting
Note 1) Without SI unit, the symbol is nil. BA —
Type Note 2) SI unit is not included in I/O unit stations.
Note 3) When I/O unit is selected, it is shipped
D
DIN rail
— —
A
10 Side ported separately, and assembled by users. mounting
B —
11 Bottom ported∗ Refer to the attached operation manual for
mounting. Note 1) Enter the number of stations inside
∗ The SY5000 manifold base is used for the
when it is larger than the number of valve
bottom ported of the SY3000. When ordering,
stations. (Refer to “DIN Rail Option”
refer to “Plug-in Mixed Mounting Type Manifold”
below.)
(from page 189).
Valve stations Note 2) Only direct mounting is available for Type
11 (Bottom ported).
Symbol Stations Note Note 3) Refer to page 247 for the fixation of DIN
SI unit 02 2 stations rail mounting type manifold.
0 Without SI unit Double wiring Note 1)
···
···
···
···
···
137
Plug-in Connector Connecting Base Series SY3000/5000/7000
Valve
A, B port size (Metric/One-touch fitting) A, B port size (Inch/One-touch fitting)
Sub-plate
Type 10/Side ported Type 11/Bottom ported Type 10/Side ported Type 11/Bottom ported
Symbol A, B port Symbol A, B port
SY3000 SY5000 SY7000 SY5000 SY7000 SY3000 SY5000 SY7000 SY5000 SY7000
C2 ø2 — — — — N1 ø1/8" — — — —
Plug-in
C3 ø3.2 — — — — N3 ø5/32" — —
Straight
C4 ø4 — — N7 ø1/4"
Straight
C6 ø6 N9 ø5/16" —
C8 ø8 — N11 ø3/8" — — —
C10 ø10 — — — CM∗ Straight port, mixed sizes
C12 ø12 — — — LN3 ø5/32" — — — —
CM∗
Upward
Straight port, mixed sizes LN7 ø1/4" — — —
Metal Base
L4 ø4 — — — LN9 ø5/16" — — — —
L6 ø6 — — LN11 ø3/8" — — — —
Upward
Elbow Note)
L8 ø8 — — — BN3 ø5/32" — — — —
Downward
L10 ø10 — — — — BN7 ø1/4" — — —
Plug-in
L12 ø12 — — — — BN9 ø5/16" — — — —
Elbow Note)
B4 ø4 — — — BN11 ø3/8" — — — —
Downward
P, E port size
ø8 ø10 ø12 ø10 ø12
(One-touch fittings)
Note) To avoid interference with the body or piping, select downward elbow port when mounting the optional spacer assembly (pages 226 to 228).
∗ Indicate the sizes on the manifold specification sheet in the case of “CM”, “LM”.
∗ The direction of P, E port fittings is the same as for A, B port. If selecting “LM”, indicate it on the manifold specification sheet for the P, E port fitting direction.
Example (SS5Y3-10S6-) SS5Y3-10S6Q42-05B-C6 ···1 set (Type 10 5-station manifold base part no.)
∗SY3100-5U1 ·······················3 sets (2-position single part no.)
∗SY3200-5U1 ·······················2 sets (2-position double part no.)
Plug-in
Digital input unit Digital output unit 2-position single ∗EX600-DXPD ·····················1 set I/O unit part number (Station 1)
EX600-DXPD EX600-DYPB SY3100-5U1 (3 sets) ∗EX600-DYPB ·····················1 set I/O unit part number (Station 2)
End plate Note 1) SI unit Note 1) 2-position double The asterisk denotes the symbol for assembly.
In this case, use caution as there is also output on the A and B port on
1 2 I/O unit stations
One-touch Fittings/
base side.
Specify on a manifold specification sheet if plugs are required on the A and
B port on base side.
Manifold Options
Protective class
class III (Mark: )
138
Series SY3000/5000/7000
How to Order Valves (With mounting screw) Refer to page 3 for valve specifications.
SY 3 1 0 0 5 1
Base mounted
Type of actuation
1 Single Coil type
2-position E: F:
2 Double Nil Standard Push-turn Slide locking
3 Closed center T With power saving circuit (Continuous duty type) locking type
4 3-position Exhaust center ∗ Be sure to select the power saving circuit type lever
5 Pressure center when the valve is continuously energized for type
A∗ N.C./N.C. long periods of time.
4-position ∗ Be careful of the energizing time when the
B∗ dual 3-port
N.O./N.O.
power saving circuit is selected. Refer to page
C∗ N.C./N.O.
244 for details. ∗ Refer to page 14 for with the safety slide locking
∗ Only rubber seal type is available for the manual override.
4-position dual 3-port valve.
Rated voltage
5 24 VDC
Protective class
class III (Mark: )
139
Plug-in Connector Connecting Base Series SY3000/5000/7000
Valve
Plug-in Type 10/Side Ported
U C2
SS5Y3-10S6 42 - Stations D - C3,
C4, N3 (D)
N1
Sub-plate
B C6, N7
D side (L3) U side
(5.3) (L4)
(DIN rail mounting hole pitch: 12.5) Manual override Note 2)
Plug-in
(L5) L1
DIN rail holding screw 5.5 L6 L2 ( Push-turn locking slotted type:
Press, then rotate it. )
(For DIN rail mounting) 47 8 DIN rail holding screw 1.5 4(A) port side
Communication connector
(For DIN rail mounting) : Blue (For rubber seal)
Power connector 2 x M4 mounting hole : Gray (For metal seal)
85.1 (Light/surge 2(B) port side : Yellow
Marker groove
voltage suppressor)
0 1
(5.5)
Metal Base
B A B A B A B A B A
2 3
(35)
92.6
14 A 14 A 14 A 14 A 14 A
83
106
PWR
90
OUT
60.5
0 1
(40.9)
4 5
2 3
Plug-in
4.6
(8)
12 B 12 B 12 B 12 B 12 B
BUS PCI BUS
IN OUT
8 7
8
1.7
4.6
)
(4.9)
C6: 3.6
N7: 7.4
86.6 FE
terminal 5.4 4 x M4 mounting hole
: ø6, ø1/4"
1 P 1 P
63.1
56.6
3/5 E 2 B2 B2 B2 B2 B 3/5 E
13.2
40.2
21.6
4 A4 A4 A4 A4 A
18
10.6
13.6
(For DIN rail
(7.5)
mounting)
One-touch fitting
(Pitch)
(11.8)
Plug-in
[1(P), 3/5(E) port] 18.3 15.5 P = 10.5 (17.8)
Applicable tube O.D.: ø8, ø5/16"
I/O (n1) 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
One-touch Fittings/
unit
stations
(n2)
0 185.5 198 210.5 223 223 235.5 248 260.5 273 285.5 285.5 298 310.5 323 335.5 348 348 360.5 373 385.5 398 410.5 423
1 235.5 248 248 260.5 273 285.5 298 310.5 323 323 335.5 348 360.5 373 385.5 385.5 398 410.5 423 435.5 448 448 460.5
2 285.5 285.5 298 310.5 323 335.5 348 348 360.5 373 385.5 398 410.5 410.5 423 435.5 448 460.5 473 485.5 485.5 498 510.5
3 323 335.5 348 360.5 373 385.5 385.5 398 410.5 423 435.5 448 448 460.5 473 485.5 498 510.5 510.5 523 535.5 548 560.5
Manifold Options
4 373 385.5 398 410.5 410.5 423 435.5 448 460.5 473 473 485.5 498 510.5 523 535.5 548 548 560.5 573 585.5 598 610.5
5 423 435.5 448 448 460.5 473 485.5 498 510.5 510.5 523 535.5 548 560.5 573 573 585.5 598 610.5 623 635.5 635.5 648
6 473 473 485.5 498 510.5 523 535.5 535.5 548 560.5 573 585.5 598 610.5 610.5 623 635.5 648 660.5 673 673 685.5 698
7 510.5 523 535.5 548 560.5 573 573 585.5 598 610.5 623 635.5 635.5 648 660.5 673 685.5 698 698 710.5 723 735.5 748
8 560.5 573 585.5 598 598 610.5 623 635.5 648 660.5 673 673 685.5 698 710.5 723 735.5 735.5 748 760.5 773 785.5 798
9 610.5 623 635.5 635.5 648 660.5 673 685.5 698 698 710.5 723 735.5 748 760.5 760.5 773 785.5 798 810.5 823 835.5 835.5
140
Series SY3000/5000/7000
Dimensions: Series SY3000 Connector Connecting Base EX600 (7/8 Inch Connector)
U C2
SS5Y3-10S6 53 - Stations D - C3,
C4, N3 (D)
N1
B C6, N7
D side (L3) U side
(5.3) (L4)
(DIN rail mounting hole pitch: 12.5)
(L5) L1 Manual override Note 2)
0 1
(5.5)
B A B A B A B A B A
2 3
(35)
92.6
14 A 14 A 14 A 14 A 14 A
83
106
90
60.5
0 1
(40.9)
4 5
PWR
2 3
4.6
(8)
12 B 12 B 12 B 12 B 12 B
BUS PCI BUS
53
IN OUT
8 7
4.6
1.7
8
)
(4.9)
C6: 3.6
N7: 7.4
36.7 FE
terminal 5.4 4 x M4 mounting hole
(
Power connector End plate
(Fitting for the type with P/E
Digital input unit ports on the U and/or D sides)
Valve plate
Input connector One-touch fitting
Output connector SI unit [4(A), 2(B) port]
Applicable tube O.D.: ø2
Digital output unit Connector for handheld terminal : ø3.2, ø1/8"
: ø4, ø5/32"
11.5
(Station 1)---(Station n)
: ø6, ø1/4"
8
1 P 1 P
63.1
56.6
3/5 E 2 B2 B2 B2 B2 B 3/5 E
13.2
40.2
21.6
4 A4 A4 A4 A4 A
18
10.6
13.6
(For DIN rail
(7.5)
One-touch fitting
mounting)
(Pitch)
(11.8)
141
Plug-in Connector Connecting Base Series SY3000/5000/7000
Valve
Plug-in Type 10/Side Ported
U C4, N3
SS5Y5-10S6 42 - Stations D - C6, N7 (D)
Sub-plate
B C8, N9
D side
(L3)
U side
(5.3) (L4)
(DIN rail mounting hole pitch: 12.5)
DIN rail holding screw
Plug-in
(L5) L1 Manual override Note 2)
(For DIN rail mounting)
Power connector
5.5
Communication connector
L6 L2
( Push-turn locking slotted type:
Press, then rotate it. )
47 8 DIN rail holding screw 1.5 4(A) port side
DIN rail
2 x M4 mounting hole (For DIN rail mounting) : Blue (For rubber seal)
(Light/surge voltage suppressor) : Gray (For metal seal)
85.1 Marker groove 2(B) port side : Yellow
0 1
Metal Base
(5.5)
BA BA BA BA BA
2 3
(35)
14 A 14 A 14 A 14 A 14 A
97.5
113.4
PWR
90
OUT
0 1
4 5
81.2
2 3
Plug-in
PCI (8)
(61.7)
BUS BUS
IN OUT
5.5
7.4
12 B 12 B 12 B 12 B 12 B
8 7
10.9
15.4
4.7
(5.9)
(8.3)
1 P 1 P
73.2
2 B2 B2 B2 B2 B
56.6
13.2
3/5 E 3/5 E
33.4
29.1
4 A4 A4 A4 A4 A
12.4
14.1
8.7
One-touch fitting
(7.5)
(For DIN rail
mounting)
Plug-in
[1(P), 3/5(E) port] (Pitch)
(11.8)
I/O (n1)
One-touch Fittings/
unit 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
stations
(n2)
0 198 223 235.5 248 273 285.5 298 310.5 335.5 348 360.5 373 398 410.5 423 448 460.5 473 485.5 510.5 523 535.5 560.5
1 248 260.5 285.5 298 310.5 335.5 348 360.5 373 398 410.5 423 448 460.5 473 485.5 510.5 523 535.5 548 573 585.5 598
2 298 310.5 323 348 360.5 373 398 410.5 423 435.5 460.5 473 485.5 510.5 523 535.5 548 573 585.5 598 623 635.5 648
3 348 360.5 373 398 410.5 423 435.5 460.5 473 485.5 498 523 535.5 548 573 585.5 598 610.5 635.5 648 660.5 685.5 698
Manifold Options
4 385.5 410.5 423 435.5 460.5 473 485.5 498 523 535.5 548 573 585.5 598 610.5 635.5 648 660.5 673 698 710.5 723 748
5 435.5 448 473 485.5 498 523 535.5 548 560.5 585.5 598 610.5 635.5 648 660.5 673 698 710.5 723 748 760.5 773 785.5
6 485.5 498 523 535.5 548 560.5 585.5 598 610.5 623 648 660.5 673 698 710.5 723 735.5 760.5 773 785.5 810.5 823 835.5
7 535.5 548 560.5 585.5 598 610.5 623 648 660.5 673 698 710.5 723 735.5 760.5 773 785.5 798 823 835.5 848 873 885.5
8 573 598 610.5 623 648 660.5 673 685.5 710.5 723 735.5 760.5 773 785.5 798 823 835.5 848 873 885.5 898 910.5 935.5
9 623 648 660.5 673 685.5 710.5 723 735.5 748 773 785.5 798 823 835.5 848 860.5 885.5 898 910.5 935.5 948 960.5 973
142
Series SY3000/5000/7000
Dimensions: Series SY5000 Connector Connecting Base EX600 (7/8 Inch Connector)
U C4, N3
SS5Y5-10S6 53 - Stations D - C6, N7 (D)
B C8, N9
D side (L3) U side
(5.3) (L4)
(DIN rail mounting hole pitch: 12.5)
(L5) L1 Manual override Note 2)
0 1
(5.5)
BA BA BA BA BA
2 3
(35)
14 A 14 A 14 A 14 A 14 A
90
97.5
0 1
113.4
4 5
81.2
PWR
2 3
PCI (8)
(61.7)
BUS BUS
60.4
IN OUT
5.5
7.4
12 B 12 B 12 B 12 B 12 B
8 7
10.9
15.4
4.7
(5.9)
(8.3)
36.7
Power connector FE terminal 5.4 4 x M5 mounting hole
1 P 1 P
73.2
2 B2 B2 B2 B2 B
56.6
13.2
3/5 E 3/5 E
33.4
29.1
4 A4 A4 A4 A4 A
14.1
12.4
8.7
(For DIN rail
(7.5)
mounting)
143
Plug-in Connector Connecting Base Series SY3000/5000/7000
Valve
Plug-in Type 10/Side Ported
U C6, N7
SS5Y7-10S6 42 - Stations D - C8,
C10, N11 (D)
N9
Sub-plate
B C12 (L3)
D side U side
(5.3) (L4)
(DIN rail mounting hole pitch: 12.5)
Manual override Note 2)
DIN rail holding screw (L5) L1
Plug-in
(For DIN rail mounting)
Power connector
5.5 L6 L2 ( Push-turn locking slotted
type: Press, then rotate it. )
2 x M4 mounting hole 47 8 DIN rail holding screw 1.5 4(A) port side
(DIN rail) Communication connector (For DIN rail mounting) : Blue (For rubber seal)
: Gray (For metal seal)
Marker groove Valve plate Light/surge voltage suppressor 2(B) port side: Yellow
85.1
0 1
(5.5)
Metal Base
B A B A B A B A B A
2 3
(35)
14 A 14 A 14 A 14 A 14 A
PWR
90
OUT
128.8
115
0 1
4 5
2 3
FE PCI
(8)
96.7
BUS BUS
IN OUT
terminal
Plug-in
(77.1)
8 7
12 B 12 B 12 B 12 B 12 B
5.5
30.8
22.8
5.4
8.8
3.9
(6)
86.6 SI unit
(17.9)
82.7
1 P 1 P
2 B2 B2 B2 B2 B
(56.6)
56.6
13.2
3/5 E 3/5 E
35.2
31.6
4 A4 A4 A4 A4 A
11.1
14.2
8.7
(Pitch)
(For DIN rail
(10)
(14.3)
mounting)
Plug-in
[1(P), 3/5(E) port]
Applicable tube O.D.: ø12, ø1/2"
I/O stations
One-touch Fittings/
unit (n1) 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
stations
(n2)
0 223 235.5 260.5 273 298 310.5 335.5 348 373 385.5 410.5 423 448 460.5 485.5 498 523 535.5 560.5 573 598 610.5 635.5
1 260.5 285.5 298 323 335.5 360.5 373 398 410.5 435.5 448 473 498 510.5 535.5 548 573 585.5 610.5 623 648 660.5 685.5
2 310.5 335.5 348 373 385.5 410.5 423 448 460.5 485.5 498 523 535.5 560.5 573 598 610.5 635.5 648 673 685.5 710.5 723
3 360.5 373 398 410.5 435.5 448 473 485.5 510.5 523 548 573 585.5 610.5 623 648 660.5 685.5 698 723 735.5 760.5 773
Manifold Options
4 410.5 423 448 460.5 485.5 498 523 535.5 560.5 573 598 610.5 635.5 648 673 685.5 710.5 723 748 760.5 785.5 798 823
5 448 473 485.5 510.5 523 548 560.5 585.5 598 623 648 660.5 685.5 698 723 735.5 760.5 773 798 810.5 835.5 848 873
6 498 523 535.5 560.5 573 598 610.5 635.5 648 673 685.5 710.5 723 748 760.5 785.5 798 823 835.5 860.5 873 898 923
7 548 560.5 585.5 598 623 635.5 660.5 673 698 723 735.5 760.5 773 798 810.5 835.5 848 873 885.5 910.5 923 948 960.5
8 598 610.5 635.5 648 673 685.5 710.5 723 748 760.5 785.5 798 823 835.5 860.5 873 898 910.5 935.5 948 973 — —
9 635.5 660.5 673 698 710.5 735.5 748 773 798 810.5 835.5 848 873 885.5 910.5 923 948 960.5 985.5 — — — —
144
Series SY3000/5000/7000
Dimensions: Series SY7000 Connector Connecting Base EX600 (7/8 Inch Connector)
U C6, N7
SS5Y7-10S6 53 - Stations D - C8,
C10, N11 (D)
N9
B C12
D side (L3) U side
(5.3) (L4)
(DIN rail mounting hole pitch: 12.5)
(L5) L1 Manual override Note 2)
0 1
(5.5)
B A B A B A B A B A
(35)
2 3
14 A 14 A 14 A 14 A 14 A
90
128.8
115
0 1
4 5
PWR
2 3
FE PCI
96.7
BUS BUS
IN OUT (8)
terminal
(77.1)
75.8
8 7
5.5
12 B 12 B 12 B 12 B 12 B
31
22.8
5.4
8.8
End plate
3.9
36.7
(6)
(9.3)
(A, B port: ø12) 4 x M5 mounting hole
(17.9)
Digital input unit
Input connector Valve plate (Fitting for the type with P/E
ports on the U and/or D sides)
Output connector SI unit
Digital output unit Connector for One-touch fitting
handheld terminal [4(A), 2(B) port]
(Station 1) (Station n) Applicable tube O.D.: ø6, ø1/4"
One-touch fitting : ø8, ø5/16"
: ø10, ø3/8"
[1(P), 3/5(E) port] : ø12
Applicable tube O.D.: ø12, ø1/2"
11.5
2
8
82.7
1 P 1 P
2 B2 B2 B2 B2 B
(56.6)
56.6
13.2
8.7
3/5 E 3/5 E
35.2
31.6
4 A4 A4 A4 A4 A
11.1
14.2
(Pitch)
(For DIN rail
(10)
(21.7)
mounting)
(14.3)
25 20.5 P = 19
145
146
One-touch Fittings/ Type 10, 11, 12 Type 50, 51, 52
Manifold Options Plug-in Connector Connecting Base Plug-in Metal Base Plug-in Sub-plate Valve
Plug Assembly Part No. Manifold Exploded View Manifold Exploded View
Plug-in Connector Connecting Base
RoHS
EX600
Series SY3000/5000/7000
Type 12
Top Ported
How to Order Manifold
SS5Y 3 12S6 Q 2 05 U
Refer to pages 186 to 188 for
dimensions of Type 12/Top
ported type.
Series SI unit output polarity, end plate type Valve stations
3 SY3000 Power supply Power supply Symbol Stations Note
SI unit output polarity with M12 with 7/8 inch
5 SY5000 connector connector 02 2 stations
7 SY7000 Without SI unit Nil Double wiring Note 1)
···
···
SI unit positive common 2 3 16 16 stations
SI unit SI unit negative common 4 5 02 2 stations
Specified layout Note 2)
Note 1) Without SI unit, the symbol is nil.
···
···
0 Without SI unit (Available up to 32 solenoids)
Note 2) Ensure a match with the common 24 24 stations
Q DeviceNet™ specification of the valve to be used. Note 1) Double wiring: 2-position single, double,
N PROFIBUS DP
3-position and 4-position valves can be used on
V CC-Link I/O unit stations all manifold stations.
ZE EtherNet/IP™ Nil None Use of a 2-position single solenoid will result in
D EtherCAT 1 1 stations an unused control signal. If this is not desired,
F PROFINET order with a specified layout.
···
···
PE PE
X X
3/5E B A B A B A B A B A 3/5E
D side U side
PWR
OUT
0 1
4 5
2 3
PCI
1P
2B 2B 2B 2B 2B
1P Nil ø8 ø10 ø12
BUS BUS
IN OUT
8 7
N ø5/16" ø3/8" ø1/2"
···
∗EX600-DYPB ······················1 set I/O unit part number (Station 2) than the standard length.
D24 For 24 stations
The asterisk denotes the symbol for assembly.
Prefix it to the part numbers of the valve etc. Note 1) When it is necessary to mount a DIN rail without an SI unit, select D0
and order DIN rail length separately, referring to L3 in the dimensions.
• The valve arrangement is numbered as the 1st station from the D side. (Refer to page 225 for part numbers of DIN rail.)
• Under the manifold part number, state the valves to be mounted, then the Note 2) Refer to page 247 for the fixation of DIN rail mounting type manifold.
I/O units in order from the 1st station as shown in the figure above.
For details about the EX600 Integrated-type (For Input/Output) Serial
If the arrangement becomes complicated, specify on a manifold Transmission System, refer to the WEB catalog or the Best Pneumatics No. 1
specification sheet. and the Operation Manual. For details about part numbers of SI units to be
Note) Do not enter the SI unit part number and the end plate part number mounted, refer to pages 213 and 214 in this catalog. (IP40 specifications may be
together. required according to the I/O unit to be selected.) Please download the Operation
Manual via SMC website, http://www.smcworld.com
147
Plug-in Connector Connecting Base Series SY3000/5000/7000
Valve
How to Order Valves (With mounting screw) Refer to page 3 for valve specifications.
SY 3 1 3 0 5 1 C6
Sub-plate
Plug-in
Top ported
Metal Base
pressure type. 02 1/4 SY7000
Plug-in
T With power saving circuit (Continuous duty type) C3 ø3.2 — —
3 Closed center
∗ Be sure to select the power saving circuit type C4 ø4 —
4 3-position Exhaust center when the valve is continuously energized for C6 ø6
5 Pressure center long periods of time. C8 ø8 —
A∗ N.C./N.C. ∗ Be careful of the energizing time when the
4-position C10 ø10 — —
B∗ dual 3-port N.O./N.O. power saving circuit is selected. Refer to page
C12
Plug-in
Back pressure check valve polarity is positive common. Select a valve from
R, U, NS or NZ when the SI unit output polarity
Nil None is negative common.
H Built-in ∗ Only “Z” and “NZ” types are available for with Type of mounting screw
∗ Refer to page 14 for with the safety slide locking Protective class
manual override. class III (Mark: )
148
Type 10 Plug-in Connector Connecting Base
Side Ported
EX250
Series SY3000/5000/7000
Type 11
Bottom Ported
···
···
Note 2) Input block cannot be mounted without SI unit. 16 16 stations
Nil None Note 3) The supply current from the SI unit of 02 2 stations
1 1 station AS-Interface applicable 1 power supply Specified layout Note 2)
···
···
system specification to the input block and (Available up to 32 solenoids)
···
···
specification sheet.
23
1
e
sid
D P, E port entry, SUP/EXH block assembly
Manifold base (5 stations) Internal pilot,
SS5Y3-10SQ1C-05D-C6 P, E port entry Internal pilot External pilot
Built-in silencer
• The valve arrangement is numbered as the 1st station from the D side.
• Under the manifold part number, state the valves to be mounted in order
from the 1st station as shown in the figure above. If the arrangement For details about the EX250 Integrated-type (For Input/Output) Serial
becomes complicated, specify on a manifold specification sheet. Transmission System, refer to the WEB catalog or the Best Pneumatics
No. 1 and the Operation Manual. For details about part numbers of SI units
Note) When mixing top ported configurations, select from page 156. to be mounted, refer to page 215 in this catalog. Please download the
In this case, use caution as there is also output on the A and B port on base side. Operation Manual via SMC website, http://www.smcworld.com
Specify on a manifold specification sheet if plugs are required on the A and B port
on base side.
149
Valve
A, B port size (Metric/One-touch fitting) A, B port size (Inch/One-touch fitting)
Sub-plate
Type 10/Side ported Type 11/Bottom ported Type 10/Side ported Type 11/Bottom ported
Symbol A, B port Symbol A, B port
SY3000 SY5000 SY7000 SY5000 SY7000 SY3000 SY5000 SY7000 SY5000 SY7000
C2 ø2 — — — — N1 ø1/8" — — — —
Plug-in
C3 ø3.2 — — — — N3 ø5/32" — —
Straight
C4 ø4 — — N7 ø1/4"
Straight
C6 ø6 N9 ø5/16" —
C8 ø8 — N11 ø3/8" — — —
C10 ø10 — — — CM∗ Straight port, mixed sizes
C12 ø12 — — — LN3 ø5/32" — — — —
CM∗
Upward
Straight port, mixed sizes LN7 ø1/4" — — —
Metal Base
L4 ø4 — — — LN9 ø5/16" — — — —
L6 ø6 — — LN11 ø3/8" — — — —
Upward
Elbow Note)
L8 ø8 — — — BN3 ø5/32" — — — —
Downward
L10 ø10 — — — — BN7 ø1/4" — — —
Plug-in
L12 ø12 — — — — BN9 ø5/16" — — — —
Elbow Note)
B4 ø4 — — — BN11 ø3/8" — — — —
Downward
P, E port size
ø8 ø10 ø12 ø10 ø12
(One-touch fittings)
Note) To avoid interference with the body or piping, select downward elbow port when mounting the optional spacer assembly (pages 226 to 228).
∗ Indicate the sizes on the manifold specification sheet in the case of “CM”, “LM”.
∗ The direction of P, E port fittings is the same as for A, B port. If selecting “LM”, indicate it on the manifold specification sheet for the P, E port fitting direction.
···
— length of specified
Plug-in
D — — 24 For 24 stations stations.
DIN rail
A mounting
B —
Protective class
class III (Mark: )
150
Series SY3000/5000/7000
How to Order Valves (With mounting screw) Refer to page 3 for valve specifications.
SY 3 1 0 0 5 1
Base mounted
Type of actuation
1 Single Coil type
2-position E: F:
2 Double Nil Standard Push-turn Slide locking
3 Closed center T With power saving circuit (Continuous duty type) locking type
4 3-position Exhaust center ∗ Be sure to select the power saving circuit type lever
5 Pressure center when the valve is continuously energized for type
A∗ N.C./N.C. long periods of time.
4-position ∗ Be careful of the energizing time when the
B∗ dual 3-port
N.O./N.O.
power saving circuit is selected. Refer to page
C∗ N.C./N.O.
244 for details. ∗ Refer to page 14 for with the safety slide locking
∗ Only rubber seal type is available for the manual override.
4-position dual 3-port valve.
Rated voltage
5 24 VDC Type of mounting screw
Seal type Nil Round head combination screw
0 Rubber seal B Hexagon socket head cap screw
1 Metal seal Light/surge voltage suppressor K
Round head combination screw
and common specification (Falling-out-prevention type)
Surge voltage Common H Hexagon socket head cap screw
Symbol With light (Falling-out-prevention type)
Pilot type suppressor specification
R — ∗ For “K” and “H”, the valve body cover has a drop
Nil Internal pilot Non-polar prevention construction to stop the mounting
U
R External pilot screws from falling out when the valve is
S — Positive removed for maintenance etc.
Z common ∗ When ordering a valve individually, the base
NS — Negative gasket is not included. Since the base gasket is
Back pressure check valve NZ common attached to the manifold, please order the base
gasket separately if it is needed for maintenance
(Built-in valve type) ∗ “R" and “U” are applicable for every SI unit. service.
Nil None However, “S” and “Z” can be used only for Refer to page 220 for part numbers of the base
H Built-in CC-Link applicable unit and “NS” and “NZ” are gasket and mounting screw.
for units which are not CC-Link applicable. ∗ "B" and "H" cannot be selected for the individual
∗ Only rubber seal type. Manifold installed type is ∗ Only “Z” and “NZ” types are available for with
available if the back pressure check valve is SUP/EXH spacer assembly, interface regulator
the power saving circuit. or double check spacer assembly with residual
required for a valve with metal seal. Refer to
page 232 for Ordering Example. However, it is pressure release valve.
not recommended to use the built-in valve type
and the manifold installed type at the same time
because it will reduce the flow.
∗ The built-in valve type back pressure check
valve is not available for the 3-position type and
the SY7000.
Protective class
class # (Mark: )
151
Plug-in Connector Connecting Base Series SY3000/5000/7000
Valve
Plug-in Type 10/Side Ported
C2
U
SS5Y3-10S- Stations D - C3,
C4, N3 (D)
N1
Sub-plate
B C6, N7
D side U side
(L5) L1 Manual override Note 2)
Plug-in
(For DIN rail mounting) 4(A) port side : Blue (For rubber seal)
(Light/surge voltage suppressor)
: Gray (For metal seal)
DIN rail holding screw
DIN rail 2(B) port side : Yellow
(For DIN rail mounting)
(5.5)
(8)
B A B A B A B A B A
(35)
92.6
14 A 14 A 14 A 14 A 14 A
83
Metal Base
0
1
66
60.5
2
(40.9)
3
12 B 12 B 12 B 12 B 12 B
4.6
Plug-in
4.6
2.7
1.7
)
(4.9)
SI unit
C6: 3.6
N7: 7.4
7.5
(
(Fitting for the type with P/E
5.5 L6 L2 1.5 ports on the U and/or D sides)
(5.3) (L4)
63.1
1
10.6
13.6
56.6
60
3/5 E 2 B2 B2 B2 B2 B 3/5 E
40.2
2
PWR 4 A4 A4 A4 A4 A
21.6
3
18
13.2
M3
(11.8)
Plug-in
3-pin socket
Input 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
One-touch Fittings/
block
stations (n2)
0 185.5 198 210.5 223 223 235.5 248 260.5 273 285.5 285.5 298 310.5 323 335.5 348 348 360.5 373 385.5 398 410.5 423
1 210.5 223 223 235.5 248 260.5 273 285.5 285.5 298 310.5 323 335.5 348 348 360.5 373 385.5 398 410.5 423 423 435.5
2 223 235.5 248 260.5 273 285.5 285.5 298 310.5 323 335.5 348 348 360.5 373 385.5 398 410.5 423 423 435.5 448 460.5
3 248 260.5 273 285.5 285.5 298 310.5 323 335.5 348 348 360.5 373 385.5 398 410.5 423 423 435.5 448 460.5 473 485.5
Manifold Options
4 273 285.5 285.5 298 310.5 323 335.5 348 348 360.5 373 385.5 398 410.5 423 423 435.5 448 460.5 473 485.5 485.5 498
5 285.5 298 310.5 323 335.5 348 348 360.5 373 385.5 398 410.5 423 423 435.5 448 460.5 473 485.5 485.5 498 510.5 523
6 310.5 323 335.5 348 348 360.5 373 385.5 398 410.5 423 423 435.5 448 460.5 473 485.5 485.5 498 510.5 523 535.5 548
7 335.5 348 348 360.5 373 385.5 398 410.5 423 423 435.5 448 460.5 473 485.5 485.5 498 510.5 523 535.5 548 548 560.5
8 348 360.5 373 385.5 398 410.5 423 423 435.5 448 460.5 473 485.5 485.5 498 510.5 523 535.5 548 548 560.5 573 585.5
152
Series SY3000/5000/7000
U C4, N3
SS5Y5-10S- Stations D - C6, N7 (D)
B C8, N9
D side U side
(L5) L1
Manual override Note 2)
18 21 63
DIN rail holding screw
(For DIN rail mounting)
(Push-turn locking slotted type:
Press, then rotate it. )
4(A) port side : Blue (For rubber seal)
DIN rail holding screw (Light/surge voltage suppressor) : Gray (For metal seal)
(For DIN rail mounting) 2(B) port side : Yellow
Input block
DIN rail SI unit
(5.5)
(8)
BA BA BA BA BA
(35)
14 A 14 A 14 A 14 A 14 A
0
97.5
113.4
1
66
81.2
3
(61.7)
5.5
12 B 12 B 12 B 12 B 12 B
23.5
10.9
4.7
(5.9)
2 x M4 mounting hole
(8.3)
4 x M5 mounting hole
5.5 L6 L2 1.5 (Fitting for the type with P/E
ports on the U and/or D sides)
(5.3) (L4)
(DIN rail mounting hole pitch: 12.5)
(L3)
One-touch fitting
[4(A), 2(B) port]
(Station 1) ----------- (Station n) Applicable tube O.D.: ø4, ø5/32"
One-touch fitting : ø6, ø1/4"
[1(P), 3/5(E) port] : ø8, ø5/16"
Applicable tube O.D.: ø10, ø3/8"
0
BUS 1 P 1 P
73.2
1 2 B2 B2 B2 B2 B
56.6
60
12.4
13.2
2
3/5 E 3/5 E
33.4
29.1
PWR
3
4 A4 A4 A4 A4 A
14.1
8.7
(For DIN rail
(7.5)
mounting)
M3 (Pitch)
(11.8)
20 18 P = 16 (20.5)
4 x M8 2 x M12
3-pin socket
153
Plug-in Connector Connecting Base Series SY3000/5000/7000
Valve
Plug-in Type 10/Side Ported
C6, N7
U
SS5Y7-10S- Stations D - C8,
C10, N11 (D)
N9
Sub-plate
B C12
U side
D side (L5) Manual override Note 2)
L1
18 21 63 DIN rail holding screw
(For DIN rail mounting)
(
Push-turn locking slotted type:
Press, then rotate it. )
DIN rail holding screw
Plug-in
4(A) port side : Blue (For rubber seal)
(For DIN rail mounting) (Light/surge voltage suppressor) : Gray (For metal seal)
Input 2(B) port side : Yellow
connector
SI unit
(8) (DIN rail)
B A B A B A B A B A
(35)
14 A 14 A 14 A 14 A 14 A
0
1
66
128.8
115
Metal Base
2
(5.5)
96.7
(77.1)
12 B 12 B 12 B 12 B 12 B
5.5
38.9
Plug-in
8.8
3.9
2 x M4 mounting hole (6)
(9.3)
82.7
1 P 1 P
BUS 2 B2 B2 B2 B2 B
1
56.6
60
13.2
14.2
2 3/5 E 3/5 E
11.1
35.2
8.7
4 A4 A4 A4 A4 A
31.6
PWR
3
(For DIN rail
(Pitch)
(10)
M3
Plug-in
mounting)
25 20.5 P = 19 (21.7)
2 x M12
(14.3)
4 x M8
3-pin socket
Valve
One-touch Fittings/
stations
(n1) 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
I/O unit
stations (n2)
0 223 235.5 260.5 273 298 310.5 335.5 348 373 385.5 410.5 423 448 460.5 485.5 498 523 535.5 560.5 573 598 610.5 635.5
1 235.5 260.5 273 298 310.5 335.5 348 373 385.5 410.5 423 448 460.5 485.5 498 523 548 560.5 585.5 598 623 635.5 660.5
2 260.5 273 298 310.5 335.5 348 373 398 410.5 435.5 448 473 485.5 510.5 523 548 560.5 585.5 598 623 635.5 660.5 673
Manifold Options
3 285.5 298 323 335.5 360.5 373 398 410.5 435.5 448 473 485.5 510.5 523 548 560.5 585.5 598 623 635.5 660.5 673 698
4 298 323 335.5 360.5 373 398 410.5 435.5 448 473 485.5 510.5 523 548 573 585.5 610.5 623 648 660.5 685.5 698 723
5 323 335.5 360.5 373 398 423 435.5 460.5 473 498 510.5 535.5 548 573 585.5 610.5 623 648 660.5 685.5 698 723 735.5
6 348 360.5 385.5 398 423 435.5 460.5 473 498 510.5 535.5 548 573 585.5 610.5 623 648 660.5 685.5 698 723 748 760.5
7 360.5 385.5 398 423 435.5 460.5 473 498 510.5 535.5 548 573 598 610.5 635.5 648 673 685.5 710.5 723 748 760.5 785.5
8 385.5 398 423 448 460.5 485.5 498 523 535.5 560.5 573 598 610.5 635.5 648 673 685.5 710.5 723 748 760.5 785.5 798
154
Plug-in Connector Connecting Base
EX250
Series SY3000/5000/7000
Type 12
Top Ported
SS5Y 3 12S Q 05 U
Refer to pages 186 to 188 for
dimensions of Type 12/Top
ported type.
Series SI unit Valve stations
3 SY3000 0 Without SI unit Symbol Stations Note
5 SY5000 Q DeviceNet™ (Negative common) 02 2 stations
7 SY7000 N PROFIBUS DP (Negative common) Double wiring Note 1)
···
···
V CC-Link (Positive common) 16 16 stations
Input block stations TA 2 power 8 in/8 out, 31 slave modes
AS-Interface supply 4 in/4 out, 31 slave modes
02 2 stations
Specified layout Note 2)
TB
···
···
systems
Nil None (Negative 1 power (Available up to 32 solenoids)
1 1 station
TC common) supply 8 in/8 out, 31 slave modes 24 24 stations
TD systems 4 in/4 out, 31 slave modes Note 1) Double wiring: 2-position single, double, 3-position
···
···
8 8 stations
Y CANopen (Negative common) and 4-position valves can be used on all manifold
stations.
ZE EtherNet/IP™ (Negative common) Use of a 2-position single solenoid will result in an
Note) Without SI unit, the symbol is nil. The
maximum number of stations is limited for Note 1) Ensure a match with the common specification unused control signal. If this is not desired, order with
a specified layout.
the AS-Interface applicable SI unit. of the valve to be used. Note 2) Specified layout: Indicate the wiring specifications on
Note 2) Input block cannot be mounted without SI unit. the manifold specification sheet. (Note that 2-position
Note 3) The supply current from the SI unit of
Input block type AS-Interface applicable 1 power supply system
double, 3-position and 4-position valves cannot be
used where single wiring has been specified.)
PNP input NPN input specification to the input block and valve is When determining the number of valve stations, note
limited. that the maximum number of solenoids for the
(Positive common) (Negative common)
AS-Interface applicable SI unit specification is as
Without input block Nil follows.
M12, 2 inputs A D • 8 in/8 out specification: Max. 8 solenoids
• 4 in/4 out specification: Max. 4 solenoids
M12, 4 inputs B E Note 3) This also includes the number of blanking plate
M8, 4 inputs C F assembly.
Note 4) For the product without the SI unit (S0), note the
Note) Without SI unit, the symbol is nil. maximum number of solenoids of the SI unit that will
be mounted. If the layout is specified, indicate it on
the manifold specification sheet.
How to Order Manifold Assembly P, E port entry, SUP/EXH block assembly
Internal pilot,
P, E port entry Internal pilot External pilot
Built-in silencer
Example (SS5Y3-12S-) U side (2 to 10 stations) U C Note) G
3-position closed
center (24 VDC) D side (2 to 10 stations) D E Note) H
2-position double (24 VDC)
SY3330-5U1-C6 (1 set) Both sides (2 to 24 stations) B — J
SY3230-5U1-C6 (1 set)
∗ For built-in silencer type, P and E ports are available on U and D sides. 3/5(E) port is plugged.
2-position single (24 VDC) The silencer exhaust port is located on the opposite side of P, E port entry. (Example: When the
SY3130-5U1-C6 (3 sets) P, E port entry is D side, the silencer exhaust port is U side.)
∗ When the built-in silencer type is used, keep the exhaust port from coming in direct contact with
water or other liquids.
Note) For SUP/EXH block assembly specifications, built-in silencer types will have P port entry
stipulated.
ide
Us P, E port size (One-touch fittings)
s
n
tio
ta
2 3
1 Nil ø8 ø10 ø12
ide
Ds
N ø5/16" ø3/8" ø1/2"
Manifold base (5 stations) ∗ For N, sizes are in inches.
SS5Y3-12SQ1C-05D
Mounting Note 1) If the DIN rail must be mounted
SS5Y3-12SQ1C-05D ···1 set (Type 12 5-station manifold base part no.)
Nil Direct mounting without an SI unit, select D0. Then,
D DIN rail mounting (With DIN rail) refer to L3 of the dimensions for the
∗SY3130-5U1-C6 ···········3 sets (2-position single part no.) DIN rail length and order separately.
∗SY3230-5U1-C6 ···········1 set (2-position double part no.) D0 DIN rail mounting (Without DIN rail) (Refer to page 225 for the DIN rail
∗SY3330-5U1-C6 ···········1 set (3-position closed center part no.) D3 For 3 stations Specify a longer part number.)
rail than the Note 2) Refer to page 247 for the fixation of
···
···
The asterisk denotes the symbol for assembly. DIN rail mounting type manifold.
Prefix it to the part numbers of the valve etc. D24 For 24 stations standard length.
• The valve arrangement is numbered as the 1st station from the D side. For details about the EX250 Integrated-type (For Input/Output) Serial
• Under the manifold part number, state the valves to be mounted in order Transmission System, refer to the WEB catalog or the Best Pneumatics No. 1
from the 1st station as shown in the figure above. If the arrangement and the Operation Manual. For details about part numbers of SI units to be
becomes complicated, specify on a manifold specification sheet. mounted, refer to page 215 in this catalog. Please download the Operation Manual
via SMC website, http://www.smcworld.com
155
Plug-in Connector Connecting Base Series SY3000/5000/7000
Valve
How to Order Valves (With mounting screw) Refer to page 3 for valve specifications.
SY 3 1 3 0 5 1 C6
Sub-plate
Plug-in
Top ported
Metal Base
pressure type. 02 1/4 SY7000
Type of actuation One-touch fitting (Metric)
1 Single Coil type Symbol A, B port SY3000 SY5000 SY7000
2-position C2
2 Double Nil Standard ø2 — —
Plug-in
3 Closed center T With power saving circuit (Continuous duty type) C3 ø3.2 — —
4 3-position Exhaust center ∗ Be sure to select the power saving circuit type C4 ø4 —
5 Pressure center when the valve is continuously energized for C6 ø6
A∗ N.C./N.C. long periods of time. C8 ø8 —
4-position ∗ Be careful of the energizing time when the
B∗ dual 3-port
N.O./N.O. C10 ø10 — —
power saving circuit is selected. Refer to page
C∗ C12
Plug-in
(Built-in valve type) However, “S” and “Z” can be used only for
CC-Link applicable unit and “NS” and “NZ” are
Nil None for units which are not CC-Link applicable. Type of mounting screw
H Built-in ∗ Only “Z” and “NZ” types are available for with
∗ Refer to page 14 for with the safety slide locking Protective class
manual override. class III (Mark: )
156
Type 10 Plug-in Connector Connecting Base
Side Ported
EX260
Series SY3000/5000/7000
Type 11
Bottom Ported
RoHS
How to Order Manifold
···
Type 16 16 stations
02 2 stations SUP/EXH block assembly
10 Side ported Specified layout Note 2) Nil Internal pilot
···
···
···
···
···
157
Valve
Sub-plate
A, B port size (Metric/One-touch fitting) A, B port size (Inch/One-touch fitting)
Plug-in
Type 10/Side ported Type 11/Bottom ported Type 10/Side ported Type 11/Bottom ported
Symbol A, B port Symbol A, B port
SY3000 SY5000 SY7000 SY5000 SY7000 SY3000 SY5000 SY7000 SY5000 SY7000
C2 ø2 — — — — N1 ø1/8" — — — —
C3 ø3.2 — — — — N3 ø5/32" — —
Straight
C4 ø4 — — N7 ø1/4"
Straight
C6 ø6 N9 ø5/16" —
C8 N11
Metal Base
ø8 — ø3/8" — — —
C10 ø10 — — — CM∗ Straight port, mixed sizes
C12 ø12 — — — LN3 ø5/32" — — — —
CM∗
Upward
Straight port, mixed sizes LN7 ø1/4" — — —
L4 ø4 — — — LN9 ø5/16" — — — —
Plug-in
L6 ø6 — — LN11 ø3/8" — — — —
Upward
Elbow Note)
L8 ø8 — — — BN3 ø5/32" — — — —
Downward
L10 ø10 — — — — BN7 ø1/4" — — —
L12 ø12 — — — — BN9 ø5/16" — — — —
Elbow Note)
Note) To avoid interference with the body or piping, select downward elbow port when mounting the optional spacer assembly (pages 226 to 228).
∗ Indicate the sizes on the manifold specification sheet in the case of “CM”, “LM”.
∗ The direction of P, E port fittings is the same as for A, B port. If selecting “LM”, indicate it on the manifold specification sheet for the P, E port fitting direction.
Plug-in
Manifold Exploded View
Example (SS5Y3-10SNAN-)
• The valve arrangement is numbered as the 1st station from the D side.
• Under the manifold part number, state the valves to be mounted in
Plug Assembly Part No.
One-touch Fittings/
Note) When mixing top ported configurations, select from page 164.
ta
S
Ds
SS5Y3-10SNAN-04D-C6
Protective class
class III (Mark: )
158
Series SY3000/5000/7000
How to Order Valves (With mounting screw) Refer to page 3 for valve specifications.
SY 3 1 0 0 5 1
Base mounted
5 24 VDC
Seal type Type of mounting screw
0 Rubber seal Nil Round head combination screw
1 Metal seal Light/surge voltage suppressor B Hexagon socket head cap screw
and common specification Round head combination screw
Surge voltage Common K (Falling-out-prevention type)
Symbol With light
suppressor specification
Pilot type R — H
Hexagon socket head cap screw
Non-polar (Falling-out-prevention type)
Nil Internal pilot U ∗ For “K” and “H”, the valve body cover has a drop
R External pilot S — Positive
prevention construction to stop the mounting
Z common screws from falling out when the valve is
NS — Negative removed for maintenance etc.
NZ common ∗ When ordering a valve individually, the base
Back pressure check valve
gasket is not included. Since the base gasket is
(Built-in valve type) ∗ Select a valve from R, U, S or Z when the SI unit
attached to the manifold, please order the base
output polarity is Nil (positive common). Select a
Nil None valve from R, U, NS or NZ when the SI unit
gasket separately if it is needed for maintenance
H Built-in service.
output polarity is N (negative common).
Refer to page 220 for part numbers of the base
∗ Only rubber seal type. Manifold installed type is ∗ Only “Z” and “NZ” types are available for with
gasket and mounting screw.
available if the back pressure check valve is the power saving circuit.
∗ “B” and “H” cannot be selected for the individual
required for a valve with metal seal. Refer to SUP/EXH spacer assembly, interface regulator
page 232 for details. However, it is not or double check spacer assembly with residual
recommended to use the built-in valve type and pressure release valve.
the manifold installed type at the same time
because it will reduce the flow.
∗ The built-in valve type back pressure check
valve is not available for the 3-position type and
the SY7000.
Protective class
class III (Mark: )
159
Plug-in Connector Connecting Base Series SY3000/5000/7000
Valve
Plug-in Type 10/Side Ported
U C2
D - C3, N3 (D)
N1
B C4,
Sub-plate
C6, N7
D side U side
Manual override Note 2)
(
Push-turn locking slotted type:
Press, then rotate it. )
Plug-in
(L5) 4(A) port side : Blue (For rubber seal)
DIN rail holding screw L1
: Gray (For metal seal)
(For DIN rail mounting)
2(B) port side : Yellow
(Light/surge voltage
(DIN rail) suppressor) (8)
(5.5)
Metal Base
B A B A B A B A
(35)
92.6
14 A 14 A 14 A 14 A
83
80.2
(114.8)
60.5
(40.9)
12 B 12 B 12 B 12 B
4.6
Plug-in
22.2
4.6
1.7
(4.9) 4 x M4 mounting hole
SI unit
) C6: 3.6
N7: 7.4
manual override)
1 P
(Slide locking
1 P 1 P
76.7
76.7
63.1
10.6
13.6
BUS IN 68.8
56.6
3/5 E 2 B2
3/5 E 2 B2 B2 B2 B2 B 3/5 E
40.2
PWR 4 A4 PWR
21.6
4 A4 A4 A4 A4 A
Plug-in
18
15.5 (Pitch)
n: Stations 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17
L1 103.7 114.2 124.7 135.2 145.7 156.2 166.7 177.2 187.7 198.2 208.7 219.2 229.7 240.2 250.7 261.2
Plug Assembly Part No.
One-touch Fittings/
L2 63 73.5 84 94.5 105 115.5 126 136.5 147 157.5 168 178.5 189 199.5 210 220.5
L3 135.5 148 148 160.5 173 185.5 198 210.5 223 223 235.5 248 260.5 273 285.5 285.5
L4 125 137.5 137.5 150 162.5 175 187.5 200 212.5 212.5 225 237.5 250 262.5 275 275
L5 16 17 11.5 12.5 13.5 14.5 15.5 16.5 17.5 12.5 13.5 14.5 15.5 16.5 17.5 12
n: Stations 18 19 20 21 22 23 24
Manifold Options
160
Series SY3000/5000/7000
U C4, N3
SS5Y5-10S- D - C6, N7 (D)
B C8, N9
D side U side Manual override Note 2)
(5.5)
B A B A B A B A
(35)
14 A 14 A 14 A 14 A
(114.8)
97.5
113.4
101
81.2
(61.7)
5.5
12 B 12 B 12 B 12 B
10.9
1.4
4.7
(5.9)
(8.3)
SI unit
4 x M5 mounting hole
34.2 L2 1.5
(5.3) (L4)
(DIN rail mounting hole pitch: 12.5) (Fitting for the type with P/E
(L3) ports on U and/or D sides)
One-touch fitting
[4(A), 2(B) port]
One-touch fitting Applicable tube O.D.: : ø4, ø5/32"
[Communication connector D-sub] [1(P), 3/5(E) port] : ø6, ø1/4"
Applicable tube O.D.: ø10 (Station 1) ----------- (Station n) : ø8, ø5/16"
: ø3/8"
BUS
manual override)
1 P BUS OUT (Slide locking
76.7
2 B2
78.9
1 P 1 P
76.7
14.1
73.2
3/5 E BUS IN 2 B2 B2 B2 B2 B
56.6
PWR
3/5 E 3/5 E
33.4
4 A4
29.1
PWR
4 A4 A4 A4 A4 A
48.2
8.7
12.4
(20.5)
(11.8)
(Pitch)
(7.5)
48.2 18 P=16
n: Stations 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17
L1 120.7 136.7 152.7 168.7 184.7 200.7 216.7 232.7 248.7 264.7 280.7 296.7 312.7 328.7 344.7 360.7
L2 80 96 112 128 144 160 176 192 208 224 240 256 272 288 304 320
L3 148 160.5 185.5 198 210.5 235.5 248 260.5 273 298 310.5 323 348 360.5 373 385.5
L4 137.5 150 175 187.5 200 225 237.5 250 262.5 287.5 300 312.5 337.5 350 362.5 375
L5 13.5 12 16.5 14.5 13 17.5 15.5 14 12 16.5 15 13 17.5 16 14 12.5
n: Stations 18 19 20 21 22 23 24
L1 376.7 392.7 408.7 424.7 440.7 456.7 472.7
L2 336 352 368 384 400 416 432
L3 410.5 423 435.5 448 473 485.5 498
L4 400 412.5 425 437.5 462.5 475 487.5
L5 17 15 13.5 11.5 16 14.5 12.5
161
Plug-in Connector Connecting Base Series SY3000/5000/7000
Valve
Plug-in Type 10/Side Ported
C6, N7
U
SS5Y7-10S- Stations D - C8,
C10, N11 (D)
N9
D side U side
Sub-plate
B C12
(L5) L1
DIN rail holding screw Manual override Note 2)
(For DIN rail mounting) Light/surge voltage suppressor
(
Push-turn locking slotted type:
Press, then rotate it. )
Plug-in
4(A) port side: Blue (For rubber seal)
2(B) port side: Yellow
B A B A B A B A
(35)
14 A 14 A 14 A 14 A 14 A
102.3
128.8
Metal Base
115
(5.5)
96.7
(77.1)
12 B 12 B 12 B 12 B 12 B
5.5
Plug-in
14
8.8
3.9
SI unit
(6)
(9.3)
One-touch fitting
[1(P), 3/5(E) port]
2
BUS OUT
BUS OUT
1 P 1 P
82.7
76.7
1 P 2 B2 B2 B2 B2 B
76.7
BUS IN
2 B2
56.6
BUS IN
3/5 E 3/5 E
11.1
35.2
8.7
31.6
3/5 E PWR 4 A4 A4 A4 A4 A
Plug-in
PWR 4 A4
14.2
(21.7)
(10)
mounting)
(Pitch)
53.2 20.5 P = 19 One-touch fitting
[4(A), 2(B) port]
Applicable tube O.D.: ø6, ø1/4"
: ø8, ø5/16"
: ø10, ø3/8"
: ø12
Note 1) These figures show the “SS5Y7-10SQA-05D-C10”.
Plug Assembly Part No.
Note 2) Refer to page 183 for dimensions of external pilot, silencer, elbow fittings and slide locking manual override.
One-touch Fittings/
n: Stations 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
L1 134.9 153.9 172.9 191.9 210.9 229.9 248.9 267.9 286.9 305.9 324.9 343.9 362.9 381.9 400.9 419.9 438.9 457.9 476.9 495.9 514.9 533.9 552.9
Manifold Options
L2 94 113 132 151 170 189 208 227 246 265 284 303 322 341 360 379 398 417 436 455 474 493 512
L3 160.5 185.5 198 223 235.5 260.5 273 298 310.5 335.5 348 373 398 410.5 435.5 448 473 485.5 510.5 523 548 560.5 585.5
L4 150 175 187.5 212.5 225 250 262.5 287.5 300 325 337.5 362.5 387.5 400 425 437.5 462.5 475 500 512.5 537.5 550 575
L5 13 16 12.5 15.5 12.5 15.5 12 15 12 15 11.5 14.5 17.5 14.5 17.5 14 17 14 17 13.5 16.5 13.5 16.5
162
Plug-in Connector Connecting Base
RoHS
EX260
Series SY3000/5000/7000
Type 12
Top Ported
How to Order Manifold
···
(Available up to 32 solenoids)
0 Without SI unit 24 24 stations
Nil Internal pilot
QA 32 In the case of the 16-output SI unit
DeviceNet™ M12 S Internal pilot, Built-in silencer
QB 16
Symbol Stations Note
NA 32
R External pilot
M12 02 2 stations
NB PROFIBUS 16 ∗ For built-in silencer type, P and E ports are available on U
Double wiring Note 1)
···
···
···
VB 16 (Available up to 16 solenoids) ∗ When the built-in silencer type is used, keep the exhaust
16 16 stations port from coming in direct contact with water or other
DA 32
Note 1) Double wiring: 2-position single, double,
EtherCAT M12 liquids.
DB 16 3-position and 4-position valves can be used
FA 32 on all manifold stations. P, E port size (One-touch fittings)
PROFINET M12 Use of a 2-position single solenoid will result
FB 16
in an unused control signal. If this is not Symbol SY3000 SY5000 SY7000
EA 32
EtherNet/IP™ M12 desired, order with a specified layout.
EB 16 Note 2) Specified layout: Indicate the wiring Nil ø8 ø10 ø12
Note) IP40 for the D-sub applicable communication specifications on the manifold specification
connector specification. sheet. N ø5/16" ø3/8" ø1/2"
DIN rail cannot be mounted without SI unit. (Note that 2-position double, 3-position and ∗ For N, sizes are in inches.
4-position valves cannot be used where
SI unit output polarity single wiring has been specified.) Mounting
Note 3) This also includes the number of blanking
Nil Positive common (NPN) plate assembly. Nil Direct mounting
N Negative common (PNP) Note 4) For the model without the SI unit (S0), note D DIN rail mounting (With DIN rail)
Note 1) Ensure a match with the common
the maximum number of solenoids of the SI D0 DIN rail mounting (Without DIN rail)
unit that will be mounted. If the layout is D3 For 3 stations
specification of the valve to be used. specified, indicate it on the manifold Specify a longer rail than
Note 2) Without SI unit, the symbol is nil.
···
···
Example (SS5Y3-12SNAN-)
2-position single (24 VDC) 2-position double (24 VDC)
SS5Y3-12SNAN-04D ····· 1 set (Type 12 4-station manifold base part no.)
SY3130-5U1-C6 (2 sets) SY3230-5U1-C6 (1 set)
∗SY3130-5U1-C6 ············· 2 sets (2-position single part no.)
3-position closed center (24 VDC) ∗SY3230-5U1-C6 ············· 1 set (2-position double part no.)
SY3330-5U1-C6 (1 set) ∗SY3330-5U1-C6 ············· 1 set (3-position closed center part no.)
The asterisk denotes the symbol for assembly.
Prefix it to the part numbers of the valve etc.
• The valve arrangement is numbered as the 1st station from the D side.
• Under the manifold part number, state the valves to be mounted in
de
specification sheet.
S
3
2
1
SS5Y3-12SNAN-04D
163
Plug-in Connector Connecting Base Series SY3000/5000/7000
Valve
How to Order Valves (With mounting screw) Refer to page 3 for valve specifications.
SY 3 1 3 0 5 1 C6
Sub-plate
Plug-in
Top ported
Metal Base
periods of time. 02 1/4 SY7000
Type of actuation ∗ Be careful of the energizing time when the
power saving circuit is selected. Refer to page One-touch fitting (Metric)
1 Single 244 for details.
2-position Symbol A, B port SY3000 SY5000 SY7000
2 Double
C2 ø2 — —
3 Closed center Rated voltage
Plug-in
C3 ø3.2 — —
4 3-position Exhaust center
5 24 VDC C4 ø4 —
5 Pressure center
C6 ø6
A∗ N.C./N.C.
4-position C8 ø8 —
B∗ N.O./N.O.
C∗
dual 3-port
N.C./N.O. Light/surge voltage suppressor C10 ø10 — —
C12
Plug-in
H Built-in Nil: D: Type of mounting screw
∗ Only rubber seal type. Manifold installed type is Non-locking Push-turn
available if the back pressure check valve is push type locking slotted Nil Round head combination screw
Nil Standard (102 psi (0.7 MPa)) attached to the manifold, please order the base
B Quick response type (102 psi (0.7 MPa)) gasket separately if it is needed for maintenance
K∗ High pressure type (145 psi (1.0 MPa)) service.
∗ Refer to page 14 for with the safety slide locking Refer to page 220 for part numbers of the base
∗ Only metal seal type is available for the high manual override.
pressure type. gasket and mounting screw.
∗ “B” and “H” cannot be selected for the individual
SUP/EXH spacer assembly or interface
Manifold Options
regulator.
Protective class
class III (Mark: )
164
Type 10 Plug-in Connector Connecting Base RoHS
Side Ported
EX126
Series SY3000/5000/7000
Type 11
Bottom Ported
···
···
bottom ported of the SY3000. When ordering, 08 8 stations
refer to “Plug-in Mixed Mounting Type Manifold” 02 2 stations
(from page 189). Specified layout Note 2)
···
···
(Available up to 16 solenoids)
16 16 stations
Note 1) Double wiring: 2-position single, double,
SI unit 3-position and 4-position valves can be used on
0 Without SI unit all manifold stations.
V CC-Link (Positive common NPN) Use of a 2-position single solenoid will result in
an unused control signal. If this is not desired,
∗ Only a terminal block plate is mounted for the
order with a specified layout.
valve without SI unit.
Note 2) Specified layout: Indicate the wiring
specifications with the manifold specification
sheet. (Note that 2-position double, 3-position
How to Order Manifold Assembly and 4-position valves cannot be used where
single wiring has been specified.)
Note 3) This also includes the number of blanking plate
Example (SS5Y3-10S4V--) assembly.
165
Plug-in Connector Connecting Base Series SY3000/5000/7000
Valve
Sub-plate
A, B port size (Metric/One-touch fitting) A, B port size (Inch/One-touch fitting)
Plug-in
Type 10/Side ported Type 11/Bottom ported Type 10/Side ported Type 11/Bottom ported
Symbol A, B port Symbol A, B port
SY3000 SY5000 SY7000 SY5000 SY7000 SY3000 SY5000 SY7000 SY5000 SY7000
C2 ø2 — — — — N1 ø1/8" — — — —
C3 ø3.2 — — — — N3 ø5/32" — —
Straight
C4 ø4 — — N7 ø1/4"
Straight
C6 ø6 N9 ø5/16" —
C8 ø8 — N11 ø3/8" — — —
Metal Base
C10 ø10 — — — CM∗ Straight port, mixed sizes
C12 ø12 — — — LN3 ø5/32" — — — —
CM∗
Upward
Straight port, mixed sizes LN7 ø1/4" — — —
L4 — — — LN9
Plug-in
ø4 ø5/16" — — — —
L6 ø6 — — LN11 ø3/8" — — — —
Upward
Elbow Note)
L8 ø8 — — — BN3 ø5/32" — — — —
Downward
L10 ø10 — — — — BN7 ø1/4" — — —
L12 ø12 — — — — BN9 ø5/16" — — — —
Elbow Note)
P, E port size
Note) To avoid interference with the body or piping, select downward elbow port when mounting the optional spacer assembly (pages 226 to 228).
∗ Indicate the sizes on the manifold specification sheet in the case of “CM”, “LM”.
∗ The direction of P, E port fittings is the same as for A, B port. If selecting “LM”, indicate it on the manifold specification sheet for the P, E port fitting direction.
Plug-in
Symbol Mounting
Name plate Station number
Nil — —
Direct
AA mounting
···
Protective class
class III (Mark: )
166
Series SY3000/5000/7000
How to Order Valves (With mounting screw) Refer to page 3 for valve specifications.
SY 3 1 0 0 5 1
Base mounted
Type of actuation
1 Single Coil type
2-position E: F:
2 Double Nil Standard Push-turn Slide locking
3 Closed center T With power saving circuit (Continuous duty type) locking type
4 3-position Exhaust center ∗ Be sure to select the power saving circuit type lever
5 Pressure center when the valve is continuously energized for type
A∗ N.C./N.C. long periods of time.
4-position ∗ Be careful of the energizing time when the
B∗ dual 3-port
N.O./N.O.
power saving circuit is selected. Refer to page
C∗ N.C./N.O.
244 for details. ∗ Refer to page 14 for with the safety slide locking
∗ Only rubber seal type is available for the manual override.
4-position dual 3-port valve.
Rated voltage
5 24 VDC Type of mounting screw
Seal type
Nil Round head combination screw
0 Rubber seal
B Hexagon socket head cap screw
1 Metal seal
Light/surge voltage suppressor K
Round head combination screw
and common specification (Falling-out-prevention type)
Surge voltage Common H Hexagon socket head cap screw
Pilot type Symbol With light (Falling-out-prevention type)
suppressor specification
Nil Internal pilot R — ∗ For “K” and “H”, the valve body cover has a drop
Non-polar prevention construction to stop the mounting
R External pilot U
screws from falling out when the valve is
S — Positive
removed for maintenance etc.
Z common
∗ When ordering a valve individually, the base
∗ Only “Z” type is available for with the power gasket is not included. Since the base gasket is
Back pressure check valve saving circuit. attached to the manifold, please order the base
(Built-in valve type) gasket separately if it is needed for maintenance
Nil None service.
H Built-in Refer to page 220 for part numbers of base
gasket and mounting screw.
∗ Only rubber seal type. Manifold installed type is ∗ “B” and “H” cannot be selected for the individual
available if the back pressure check valve is SUP/EXH spacer assembly, interface regulator
required for a valve with metal seal. Refer to or double check spacer assembly with residual
page 232 for Ordering Example. However, it is pressure release valve.
not recommended to use the built-in valve type
and the manifold installed type at the same time
because it will reduce the flow.
∗ The built-in valve type back pressure check
valve is not available for the 3-position type and
the SY7000.
Protective class
class III (Mark: )
167
Plug-in Connector Connecting Base Series SY3000/5000/7000
Valve
Plug-in Type 10/Side Ported
U C2
N1 ( )
SS5Y3-10S4V- Stations D - C3, D
Sub-plate
B C4, N3 C6, N7
D side U side
Manual override Note 2)
(L5) L1
DIN rail holding screw (Push-turn locking slotted type:
)
Plug-in
(Light/surge voltage suppressor) Press, then rotate it.
(For DIN rail mounting)
DIN rail holding screw 4(A) port side : Blue (For rubber seal)
DIN rail : Gray (For metal seal)
(For DIN rail mounting)
2(B) port side : Yellow
(5.5)
(8)
B A B A B A B A B A
Metal Base
(35)
92.6
14 A 14 A 14 A 14 A 14 A
83
116
42
80
60.5
(40.9)
4.6
12 B 12 B 12 B 12 B 12 B
36.6
Plug-in
4.6
11
1.7
)
(4.9)
15.4
4 x M4
C6: 3.6
N7: 7.4
55.4
mounting hole
2 x M5 mounting hole
(
1 (Fitting for the type with P/E
1 P 1 P
63.1
13.6
10.6
56.6
55.4
3/5 E 2 B2 B2 B2 B2 B 3/5 E
40.2
4 A4 A4 A4 A4 A
21.6
18
Plug-in
13.2
33.4
(7.5)
mounting)
(Pitch)
(11.8)
n: Stations 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
L1 164.3 174.8 185.3 195.8 206.3 216.8 227.3 237.8 248.3 258.8 269.3 279.8 290.3 300.8 311.3
L2 63 73.5 84 94.5 105 115.5 126 136.5 147 157.5 168 178.5 189 199.5 210
Manifold Options
L3 198 198 210.5 223 235.5 248 260.5 273 273 285.5 298 310.5 323 335.5 335.5
L4 187.5 187.5 200 212.5 225 237.5 250 262.5 262.5 275 287.5 300 312.5 325 325
L5 17 11.5 12.5 13.5 14.5 15.5 16.5 17.5 12.5 13.5 14.5 15.5 16.5 17.5 12
168
Series SY3000/5000/7000
U C4, N3
SS5Y5-10S4V - Stations D - C6, N7 (D)
B C8, N9
D side U side
Manual override Note 2)
(L5) L1
DIN rail holding screw
(For DIN rail mounting)
DIN rail holding screw (Push-turn locking slotted type:
Press, then rotate it. )
(For DIN rail mounting) 4(A) port side : Blue (For rubber seal)
DIN rail (Light/surge voltage suppressor) : Gray (For metal seal)
2(B) port side : Yellow
(5.5)
(8)
B A B A B A B A B A
(35)
14 A 14 A 14 A 14 A 14 A
121.4
116
42
97.5
113.4
80
81.2
(61.7)
5.5
42.4
12 B 12 B 12 B 12 B 12 B
10.9
16.4
4.7
55.4
(5.9)
(8.3)
1 P 1 P
14.1
73.2
8.7
2 B2 B2 B2 B2 B
56.6
55.4
3/5 E 3/5 E
33.4
29.1
4 A4 A4 A4 A4 A
13.2
12.4
33.4
(For DIN rail
(Pitch)
(7.5)
mounting)
108.8 18 P = 16
n: Stations 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
L1 181.3 197.3 213.3 229.3 245.3 261.3 277.3 293.3 309.3 325.3 341.3 357.3 373.3 389.3 405.3
L2 80 96 112 128 144 160 176 192 208 224 240 256 272 288 304
L3 210.5 223 248 260.5 273 285.5 310.5 323 335.5 360.5 373 385.5 398 423 435.5
L4 200 212.5 237.5 250 262.5 275 300 312.5 325 350 362.5 375 387.5 412.5 425
L5 14.5 13 17.5 15.5 14 12 16.5 15 13 17.5 16 14 12.5 17 15
169
Plug-in Connector Connecting Base Series SY3000/5000/7000
Valve
Plug-in Type 10/Side Ported
U C6, N7
SS5Y7-10S4- Stations D - C8, N9 ( )
C10, N11 D
Sub-plate
B C12
D side U side
(L5) L1
Manual override Note 2)
Plug-in
DIN rail holding screw DIN rail holding screw (Light/surge voltage suppressor) Press, then rotate it.
(For DIN rail mounting) (For DIN rail mounting) 4(A) port side: Blue (For rubber seal)
: Gray (For metal seal)
2(B) port side: Yellow
B A B A B A B A B A
Metal Base
(35)
14 A 14 A 14 A 14 A 14 A
116
42
136.8
80
128.8
115
(5.5)
96.7
(77.1)
Plug-in
57.8
12 B 12 B 12 B 12 B 12 B
5.5
31.8
8.8
4 x M5
3.9
(6)
(9.3)
(5.3) (L4)
(DIN rail mounting hole pitch: 12.5)
(L3)
One-touch fitting
[1(P), 3/5(E) port]
4 x G1/2 SI unit
(2.6)
Plug-in
90.7
1 P 1 P 82.7
2 B2 B2 B2 B2 B
56.6
55.4
3/5 E 3/5 E
11.1
35.2
8.7
31.6
4 A4 A4 A4 A4 A
(21.7)
mounting)
(10)
(14.3)
33.4 (Pitch)
Terminal block plate assembly
113.8 20.5 P = 19
One-touch fitting
[4(A), 2(B) port]
Applicable tube O.D.: ø6, ø1/4"
: ø8, ø5/16"
Plug Assembly Part No.
One-touch Fittings/
n: Stations 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
Manifold Options
L1 195.5 214.5 233.5 252.5 271.5 290.5 309.5 328.5 347.5 366.5 385.5 404.5 423.5 442.5 461.5
L2 94 113 132 151 170 189 208 227 246 265 284 303 322 341 360
L3 223 248 260.5 285.5 298 323 335.5 360.5 373 398 410.5 435.5 448 473 485.5
L4 212.5 237.5 250 275 287.5 312.5 325 350 362.5 387.5 400 425 437.5 462.5 475
L5 14 17 13.5 16.5 13.5 16.5 13 16 13 16 12.5 15.5 12.5 15.5 12
170
Plug-in Connector Connecting Base
RoHS
EX126
Type 12
Top Ported
Series SY3000/5000/7000
How to Order Manifold
···
···
(Available up to 16 solenoids)
0 Without SI unit 16 16 stations
V CC-Link (Positive common NPN)
∗ Only a terminal block plate is mounted for the
Note 1) Double wiring: 2-position single, double,
3-position and 4-position valves can be used
SUP/EXH block assembly
valve without SI unit. on all manifold stations. Nil Internal pilot
Use of a 2-position single solenoid will result S Internal pilot, Built-in silencer
in an unused control signal. If this is not R External pilot
desired, order with a specified layout.
Note 2) Specified layout: Indicate the wiring ∗ For built-in silencer type, P and E ports are
specifications on the manifold specification available on U and D sides. 3/5(E) port is
sheet. (Note that 2-position double, 3-position plugged. The silencer exhaust port is located on
and 4-position valves cannot be used where the opposite side of P, E port entry. (Example:
single wiring has been specified.) When the P, E port entry is D side, the silencer
Note 3) This also includes the number of blanking exhaust port is U side.)
plate assembly. ∗ When the built-in silencer type is used, keep the
exhaust port from coming in direct contact with
How to Order Manifold Assembly water or other liquids.
Mounting
Nil Direct mounting
ide D DIN rail mounting (With DIN rail)
Us D0 DIN rail mounting (Without DIN rail)
s
on
ati D3 For 3 stations Specify a longer rail
St
3 than the standard
···
···
2
1 D16 For 16 stations length.
e
D sid
Note) Refer to page 247 for the fixation of DIN rail
mounting type manifold.
Terminal block plate assembly
171
Plug-in Connector Connecting Base Series SY3000/5000/7000
Valve
How to Order Valves (With mounting screw) Refer to page 3 for valve specifications.
SY 3 1 3 0 5 1 C6
Sub-plate
Plug-in
Top ported
Metal Base
pressure type. 02 1/4 SY7000
Type of actuation Coil type One-touch fitting (Metric)
1 Single Symbol A, B port SY3000 SY5000 SY7000
2-position Nil Standard C2 ø2 — —
2 Double
T
Plug-in
With power saving circuit (Continuous duty type) C3 ø3.2 — —
3 Closed center
4 3-position Exhaust center ∗ Be sure to select the power saving circuit type C4 ø4 —
when the valve is continuously energized for C6 ø6
5 Pressure center
long periods of time.
A∗ N.C./N.C. ∗ Be careful of the energizing time when the
C8 ø8 —
4-position
B∗ dual 3-port
N.O./N.O. power saving circuit is selected. Refer to page C10 ø10 — —
C∗ C12
Plug-in
Nil None
H Built-in Manual override Type of mounting screw
∗ Only rubber seal type. Manifold installed type is Nil
Protective class
class III (Mark: )
172
Type 10 Plug-in Connector Connecting Base
Side Ported RoHS
EX120
Series SY3000/5000/7000
Type 11
Bottom Ported
···
···
R2 (Positive common NPN) 8 outputs 08 8 stations
V CC-Link (Positive common NPN) 02 2 stations
Type ZB Note 2) Positive common NPN
Specified layout Note 2)
···
···
CompoNet™ (Available up to 16 solenoids)
10 Side ported ZBN Note 2) Negative common PNP 16 16 stations
11 Bottom ported∗ Note 1) Ensure a match with the common specification Note 1) Double wiring: 2-position single, double,
∗ The SY5000 manifold base is used for the of the valve to be used. 3-position and 4-position valves can be
bottom ported of the SY3000. When ordering, Note 2) The communication connector (for the opposite used on all manifold stations.
refer to “Plug-in Mixed Mounting Type Manifold” side) is not provided. Please order it Use of a 2-position single solenoid will
(from page 189). separately. result in an unused control signal. If this is
not desired, order with a specified layout.
Note 2) Specified layout: Indicate the wiring
specifications on the manifold
specification sheet. (Note that 2-position
double, 3-position and 4-position valves
cannot be used where single wiring has
How to Order Manifold Assembly been specified.)
Note 3) This also includes the number of blanking
plate assembly.
Example (SS5Y3-10S3V-) Note 4) Since R2 type SI unit has 8 outputs, note
that up to 8 solenoids can be
accommodated.
2-position double (24 VDC)
2-position single (24 VDC) SY3200-5U1 (1 set)
SY3100-5U1 (3 sets) 3-position closed
P, E port entry
center (24 VDC) U U side (2 to 10 stations)
SY3300-5U1 (1 set) D D side (2 to 10 stations)
B Both sides (2 to 16 stations)
173
Plug-in Connector Connecting Base Series SY3000/5000/7000
Valve
A, B port size (Metric/One-touch fitting) A, B port size (Inch/One-touch fitting)
Sub-plate
Type 10/Side ported Type 11/Bottom ported Type 10/Side ported Type 11/Bottom ported
Symbol A, B port Symbol A, B port
SY3000 SY5000 SY7000 SY5000 SY7000 SY3000 SY5000 SY7000 SY5000 SY7000
C2 ø2 — — — — N1 ø1/8" — — — —
Plug-in
C3 ø3.2 — — — — N3 ø5/32" — —
Straight
C4 ø4 — — N7 ø1/4"
Straight
C6 ø6 N9 ø5/16" —
C8 ø8 — N11 ø3/8" — — —
C10 ø10 — — — CM∗ Straight port, mixed sizes
C12 ø12 — — — LN3 ø5/32" — — — —
CM∗
Upward
Straight port, mixed sizes LN7 ø1/4" — — —
Metal Base
L4 ø4 — — — LN9 ø5/16" — — — —
L6 ø6 — — LN11 ø3/8" — — — —
Upward
Elbow Note)
L8 ø8 — — — BN3 ø5/32" — — — —
Downward
L10 ø10 — — — — BN7 ø1/4" — — —
Plug-in
L12 ø12 — — — — BN9 ø5/16" — — — —
Elbow Note)
B4 ø4 — — — BN11 ø3/8" — — — —
Downward
P, E port size
ø8 ø10 ø12 ø10 ø12
(One-touch fittings)
Note) To avoid interference with the body or piping, select downward elbow port when mounting the optional spacer assembly (pages 226 to 228).
∗ Indicate the sizes on the manifold specification sheet in the case of “CM”, “LM”.
Plug-in
D — —
DIN rail
A mounting
B —
···
Protective class
class III (Mark: )
174
Series SY3000/5000/7000
How to Order Valves (With mounting screw) Refer to page 3 for valve specifications.
SY 3 1 0 0 5 1
Base mounted
Protective class
class III (Mark: )
175
Plug-in Connector Connecting Base Series SY3000/5000/7000
Valve
Plug-in Type 10/Side Ported
C2
U
SS5Y3-10S3- Stations D - C3,
C4, N3 (D)
N1
Sub-plate
B C6, N7
D side U side
Manual override Note 2)
(L5)
DIN rail holding screw L1
(
Push-turn locking slotted type:
)
Plug-in
(For DIN rail mounting) Press, then rotate it.
4(A) port side : Blue (For rubber seal)
(Light/surge voltage suppressor) : Gray (For metal seal)
2(B) port side : Yellow
(5.5)
(8)
B A B A B A B A B A
Metal Base
(35)
92.6
14 A 14 A 14 A 14 A 14 A
64
83
6.2
60.5
(40.9)
12 B 12 B 12 B 12 B 12 B
M3
Plug-in
Terminal screw
16.1
4.6
1.7
4.6
)
(4.9)
C6: 3.6
N7: 7.4
4 x M4 mounting hole
27.9
( L2 1.5
(Fitting for the type with P/E
ports on the U and/or D sides)
63.1
10.6
13.6
56.6
61
3/5 E 2 B2 B2 B2 B2 B 3/5 E
40.2
21.6
4 A4 A4 A4 A4 A
18
(Pitch)
mounting)
(11.8)
Plug-in
Manifold Exploded View
Type 10, 11, 12
Note 1) These figures show the “SS5Y3-10S3V-05D-C6”.
Note 2) Refer to page 181 for dimensions of external pilot, silencer, elbow fittings and slide locking manual override.
Note 3) Refer to page 186 for dimensions of A or B port top-ported type.
Plug Assembly Part No.
One-touch Fittings/
n: Stations 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
L1 96.9 107.4 117.9 128.4 138.9 149.4 159.9 170.4 180.9 191.4 201.9 212.4 222.9 233.4 243.9
L2 63 73.5 84 94.5 105 115.5 126 136.5 147 157.5 168 178.5 189 199.5 210
L3 123 135.5 148 160.5 173 173 185.5 198 210.5 223 235.5 235.5 248 260.5 273
Manifold Options
L4 112.5 125 137.5 150 162.5 162.5 175 187.5 200 212.5 225 225 237.5 250 262.5
L5 13 14 15 16 17 12 13 14 15 16 17 11.5 12.5 13.5 14.5
176
Series SY3000/5000/7000
U C4, N3
SS5Y5-10S3- Stations D - C6, N7 (D)
B C8, N9
D side U side
Manual override Note 2)
(L5) L1
DIN rail holding screw
(For DIN rail mounting)
(
Push-turn locking slotted type:
Press, then rotate it. )
4(A) port side : Blue (For rubber seal)
M3 DIN rail (Light/surge voltage suppressor) : Gray (For metal seal)
Terminal screw 2(B) port side : Yellow
(5.5)
(8)
6.2
BA BA BA BA BA
(35)
14 A 14 A 14 A 14 A 14 A
64
97.5
113.4
81.2
(61.7)
36.9
5.5
12 B 12 B 12 B 12 B 12 B
10.9
4.7
(5.9)
(8.3)
4 x M5 mounting hole
One-touch fitting
[4(A), 2(B) port]
Applicable tube O.D.: ø4, ø5/32"
One-touch fitting (Station 1) ----------- (Station n) : ø6, ø1/4"
: ø8, ø5/16"
[1(P), 3/5(E) port]
Applicable tube O.D.: ø10, ø3/8"
1 P 1 P
73.2
2 B2 B2 B2 B2 B
56.6
61
14.1
3/5 E 3/5 E
33.4
29.1
4 A4 A4 A4 A4 A
12.4
8.7
mounting)
(Pitch)
(11.8)
44.2 18 P = 16 (20.5)
n: Stations 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
L1 116.7 132.7 148.7 164.7 180.7 196.7 212.7 228.7 244.7 260.7 276.7 292.7 308.7 324.7 340.7
L2 80 96 112 128 144 160 176 192 208 224 240 256 272 288 304
L3 148 160.5 173 198 210.5 223 248 260.5 273 285.5 310.5 323 335.5 348 373
L4 137.5 150 162.5 187.5 200 212.5 237.5 250 262.5 275 300 312.5 325 337.5 362.5
L5 15.5 14 12 16.5 15 13 17.5 16 14 12.5 17 15 13.5 11.5 16
177
Plug-in Connector Connecting Base Series SY3000/5000/7000
Valve
Plug-in Type 10/Side Ported
C6, N7
U
SS5Y7-10S3- Stations D - C8,
C10, N11 (D)
N9
Sub-plate
B C12
D side U side
Manual override Note 2)
(L5) L1
(Push-turn locking slotted type:
)
Plug-in
DIN rail holding screw Press, then rotate it.
(For DIN rail mounting) 4(A) port side: Blue (For rubber seal)
(Light/surge voltage suppressor) : Gray (For metal seal)
2(B) port side: Yellow
(8)
(DIN rail)
B A B A B A B A B A
Metal Base
(35)
14 A 14 A 14 A 14 A 14 A
64
6.2
128.8
115
(5.5)
96.7
(77.1)
Plug-in
M3
50.8
12 B 12 B 12 B 12 B 12 B
5.5
Terminal screw
8.8
3.9
(6)
4 x M5 mounting hole
1 P 1 P
82.7
2 B2 B2 B2 B2 B
56.6
61
3/5 E 3/5 E
11.1
Plug-in
35.2
8.7
31.6
4 A4 A4 A4 A4 A
14.2
(21.7)
(10)
mounting)
(14.3)
(Pitch)
47.7 20.5 P = 19
One-touch fitting
[4(A), 2(B) port]
Applicable tube O.D.: ø6, ø1/4"
: ø8, ø5/16"
: ø10, ø3/8"
: ø12
Plug Assembly Part No.
One-touch Fittings/
n: Stations 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
Manifold Options
L1 129.4 148.4 167.4 186.4 205.4 224.4 243.4 262.4 281.4 300.4 319.4 338.4 357.4 376.4 395.4
L2 94 113 132 151 170 189 208 227 246 265 284 303 322 341 360
L3 160.5 173 198 210.5 235.5 248 273 285.5 310.5 335.5 348 373 385.5 410.5 423
L4 150 162.5 187.5 200 225 237.5 262.5 275 300 325 337.5 362.5 375 400 412.5
L5 15.5 12.5 15.5 12 15 12 15 11.5 14.5 17.5 14.5 17.5 14 17 14
178
Plug-in Connector Connecting Base
EX120
Series SY3000/5000/7000
Type 12
Top Ported
RoHS
How to Order Manifold
···
···
(Available up to 16 solenoids)
0 Without SI unit 16 16 stations
Q DeviceNet™ (Positive common NPN) Note 1) Double wiring: 2-position single, double,
R1 OMRON CompoBus/S 16 outputs 3-position and 4-position valves can be
SUP/EXH block assembly
R2 (Positive common NPN) 8 outputs used on all manifold stations. Nil Internal pilot
V CC-Link (Positive common NPN) Use of a 2-position single solenoid will result S Internal pilot, Built-in silencer
in an unused control signal. If this is not R External pilot
ZB Note 2) Positive common NPN
desired, order with a specified layout.
CompoNet™
ZBN Note 2) Negative common PNP Note 2) Specified layout: Indicate the wiring ∗ For built-in silencer type, P and E ports are
Note 1) Ensure a match with the common specifications on the manifold specification available on U and D sides. 3/5(E) port is
specification of the valve to be used. sheet. (Note that 2-position double, plugged. The silencer exhaust port is located on
Note 2) The communication connector (for the 3-position and 4-position valves cannot be the opposite side of P, E port entry. (Example:
opposite side) is not provided. Please used where single wiring has been When the P, E port entry is D side, the silencer
order it separately. specified.) exhaust port is U side.)
Note 3) This also includes the number of blanking
plate assembly.
Note 4) Since R2 type SI unit has 8 outputs, note
that up to 8 solenoids can be
accommodated.
How to Order Manifold Assembly P, E port size (One-touch fittings)
Symbol SY3000 SY5000 SY7000
Example (SS5Y3-12S3V-) Nil ø8 ø10 ø12
2-position double (24 VDC)
N ø5/16" ø3/8" ø1/2"
SY3230-5U1-C6 (1 set)
2-position single (24 VDC) ∗ For N, sizes are in inches.
SY3130-5U1-C6 (3 sets) 3-position closed
center (24 VDC)
SY3330-5U1-C6 (1 set)
Mounting
Nil Direct mounting
D DIN rail mounting (With DIN rail)
D0 DIN rail mounting (Without DIN rail)
D3 For 3 stations Specify a longer rail
ide than the standard
Us
···
···
ati
on
s D16 For 16 stations length.
St
3 Note 1) When mounted on the DIN rail without the
2 SI unit, please select D0 and refer to L3 of
1
Manifold base the dimensions for the DIN rail length,
ide
(5 stations) Ds then order separately. (Refer to page 225
SS5Y3-12S3V-05D for the DIN rail part number.)
Note 2) Refer to page 247 for the fixation of DIN
SS5Y3-12S3V-05D ···1 set (Type 12 5-station manifold base part no.) rail mounting type manifold.
∗SY3130-5U1-C6 ·······3 sets (2-position single part no.)
∗SY3230-5U1-C6 ·······1 set (2-position double part no.)
∗SY3330-5U1-C6 ·······1 set (3-position closed center part no.)
The asterisk denotes the symbol for assembly.
For details about the EX120 Integrated-type (For Output) Serial
Prefix it to the part numbers of the valve etc.
Transmission System, refer to the WEB catalog or the Best
• The valve arrangement is numbered as the 1st station from the D side. Pneumatics No. 1 and the Operation Manual. For details about
• Under the manifold part number, state the valves to be mounted in order part numbers of SI units to be mounted, refer to page 218 in
from the 1st station as shown in the figure above. If the arrangement this catalog. Please download the Operation Manual via SMC
becomes complicated, specify on a manifold specification sheet. website, http://www.smcworld.com
179
Plug-in Connector Connecting Base Series SY3000/5000/7000
Valve
How to Order Valves (With mounting screw) Refer to page 3 for valve specifications.
SY 3 1 3 0 5 1 C6
Sub-plate
Plug-in
Top ported
Metal Base
pressure type. 02 1/4 SY7000
Type of actuation One-touch fitting (Metric)
1 Single
2
2-position
Double
Coil type Symbol A, B port SY3000 SY5000 SY7000
C2 ø2 — —
3 Closed center Nil Standard
Plug-in
C3 ø3.2 — —
4 3-position Exhaust center T With power saving circuit (Continuous duty type)
C4 ø4 —
5 Pressure center ∗ Be sure to select the power saving circuit type
C6 ø6
A∗ N.C./N.C. when the valve is continuously energized for
C8 ø8 —
4-position
B∗ dual 3-port
N.O./N.O. long periods of time.
C10 ø10 — —
∗ Be careful of the energizing time when the
C∗ N.C./N.O.
C12
Plug-in
∗ Select a valve from R, U, S or Z when the SI unit
H Built-in
∗ Only rubber seal type. Manifold installed type is
specification is positive common. Select a valve
from R, U, NS or NZ when the SI unit
Type of mounting screw
available if the back pressure check valve is specification is ZBN (negative common). Nil Round head combination screw
∗ Refer to page 14 for with the safety slide locking Protective class
manual override. class III (Mark: )
180
Series SY3000/5000/7000
Common Dimensions
Plug-in Type 10/Side Ported
Series SY3000 Connector Connecting Base External Pilot, Silencer, Elbow Fittings, Slide Locking Manual Override
U
SS5Y3-10- Stations D (S, R)- LB D side U side
B
One-touch fitting 7.4 85.5
[PE: Pilot EXH port] (For 5 stations)
[X: External pilot port]
(73.2) (7.4) (11.6)
Applicable tube O.D.: ø4, ø5/32"
(Fitting for the type with P/E
ports on the U and/or D sides)
5.3
PE PE
LOCK
X X
3/5E B A B A B A B A B A 3/5E
14 A 14 A 14 A 14 A 14 A
(127.8)
58.5
FREE
40.9
1P 1P
12 B 12 B 12 B 12 B 12 B
11.6
6.9
1.7
17.3
27.6
35.2
7.4 85.5
manual override)
(Slide locking
(For 5 stations) 1 P
(65.4)
68.8
63.1
56.6
(43.2)
3/5 E
PE
LOCK
X
B A B A B
14 A 14 A 14
)
)
L6 : 32.4
LN7 : 34.9
L6 : 43.4
LN7 : 45.9
(Pitch)
FREE
(42.8)
(37.5)
1P
12 B 12 B
15.5 P= 10.5 (17.8)
(
78.6 One-touch fitting
Note) These figures show the “SS5Y3-10F2-05DR-L6”. (
82.3 [PE: Pilot EXH port]
[X: External pilot port]
Applicable tube O.D.: ø4, ø5/32"
LOCK
FREE
FREE
LOCK
B A B A B (11.2)
14 A 14 A 14
4(A) port
3/5(E) port
FREE
12 B 12 B
2(B) port
1(P) port
(0.2)
(7.2) (15)
Plug
3/5(E) port
181
Common Dimensions Series SY3000/5000/7000
Valve
Plug-in Type 10/Side Ported
Series SY5000 Connector Connecting Base External Pilot, Silencer, Elbow Fittings, Slide Locking Manual Override
Sub-plate
B
[X: External pilot port] (For 5 stations)
(65.4) (12)
Applicable tube O.D.: ø4, ø5/32"
(Fitting for the type with P/E
ports on the U and/or D sides)
Plug-in
PE PE
LOCK
3/5 B A B A B A B A B A 3/5
14 A 14 A 14 A 14 A 14 A
26.9
113.4
E E
FREE
X X
1 1
(159.5)
61.7
P P
52.8
12 B 12 B 12 B 12 B 12 B
4.7
12.6
17.9
Metal Base
28.6
36.9
(Fitting for the type with P/E
2(B) port ports on the U and/or D sides)
Plug-in
1(P) port
External pilot for straight piping 4(A) port One-touch fitting
(118.2) 3/5(E) port [4(A), 2(B) port]
P, E port entry: D
(For 5 stations) One-touch fitting Applicable tube O.D.: ø4
(20°) : ø6, ø1/4"
[1(P), 3/5(E) port]
Applicable tube O.D.: ø10, ø3/8" : ø8, ø5/16"
3/5 BA BA
14 A 14 A
E
X
FREE
manual override)
(59.8)
(Slide locking
P
(31.7)
12 B 12 B 12 B
78.9
1 P
66.1
(59.8)
(54.3)
(39.3)
(38.8)
3/5 E
70.8 One-touch fitting
Plug-in
LOCK
BA BA
14 A 14 A
FREE
Downward (Type B)
[SUP/EXH block] [Valve]
Plug Assembly Part No.
LOCK
LOCK
One-touch Fittings/
One-touch fitting
[4(A), 2(B) port]
LOCK
LOCK
FREE
FREE
( )
B6 : 10.7 Applicable tube O.D.: ø4, ø5/32"
BN7 : 13.2 : ø6, ø1/4"
FREE
FREE
6.5
16.9
Manifold Options
4(A) port
Series SY7000 Connector Connecting Base External Pilot, Silencer, Elbow Fittings, Slide Locking Manual Override
U
SS5Y7-10- Stations D (S, R)- LB One-touch fitting
[PE: Pilot EXH port]
D side U side
B 138.1
[X: External pilot port]
(69.5) (For 5 stations) (10.9)
Applicable tube O.D.: ø6, ø1/4"
(Fitting for the type with P/E
ports on the U and/or D sides)
PE PE
LOCK
3/5E B A B A B A B A B A 3/5E
14 A 14 A 14 A 14 A 14 A
49.4
128.8
FREE
(175.6)
1P 1P
(77.1)
X X
45.4
12 B 12 B 12 B 12 B 12 B
15.6
3.9
34.6
37.6
16.6
(Fitting for the type with P/E
1(P) port ports on the U and/or D sides)
3/5(E) port One-touch fitting
External pilot for straight piping One-touch fitting 4(A) port [4(A), 2(B) port]
P, E port entry: D Applicable tube O.D.: ø12
[1(P), 3/5(E) port] 2(B) port
(138.1) Applicable tube O.D.: ø12, ø1/2"
One-touch fitting
(For 5 stations) [4(A), 2(B) port]
(20°) Applicable tube O.D.: ø6, ø1/4"
: ø8, ø5/16"
: ø10, ø3/8"
(Station 1) (Station n)
3/5E B A B A
14 A 14 A
FREE
85.8
1 P
(For ø10, ø3/8")
(For ø12)
69.7
(53.1)
(58)
(For ø12)
1P
(For ø10, ø3/8")
(74.2)
(23.5)
(37.5)
3/5 E
(32.6)
12 B 12 B
LOCK
LOCK
B A B A
FREE
FREE
14 A 14 A
FREE
12 B 12 B
Valve
Plug-in Type 11/Bottom Ported
U
SS5Y5-11- Stations D
Sub-plate
B D side U side
L2 1.5 Manual override
(
Push-turn locking slotted type:
Press, then rotate it. )
4(A) port side : Blue (For rubber seal)
Plug-in
: Gray (For metal seal)
2(B) port side : Yellow
4 x M5 mounting hole
LOCK
BA BA BA BA B A
14 A 14 A 14 A 14 A 14 A
97.5
113.4
FREE
Metal Base
5.5
12 B 12 B 12 B 12 B 12 B
10.9
Plug-in
4.7
External pilot
P, E port entry: D (118.2) (Station 1) ---------- (Station n)
(For 5 stations)
(20°)
manual override)
(Slide locking
3/5 B A B A
8.7
14 A 14 A
4.7
E
FREE
X
1
(59.8)
(12.9)
(9.5)
P
12 B 12 B 12 B
(Fitting for the type with P/E
(31.7)
Built-in silencer
31.8
P, E port entry: D
39.7
Plug-in
15
1 P 1 P
4 A4 A4 A4 A4 A
EX500 : P. 133
Manifold Options
97.5
U L2 1.5
SS5Y7-11- Stations D D side U side
Manual override
B
( Push-turn locking slotted type:
Press, then rotate it. )
4(A) port side:
Blue (For rubber seal)
Gray (For metal seal)
2(B) port side : Yellow
LOCK
B A B A B A B A B A
14 A 14 A 14 A 14 A 14 A
115
FREE
12 B 12 B 12 B 12 B 12 B
5.5
8.8
External pilot
P, E port entry: D (138.1) 4 x M5 mounting hole
(For 5 stations)
40.1 (20°) (Station 1) (Station n)
3/5E B A B A
85.8
82.7
14 A 14 A
56.6
FREE
8.7
1P
(74.2)
12 B 12 B
9.1
(12)
(14.5)
(23.5)
X
(23.9)
Built-in silencer
P, E port entry: D
Silencer (Exhaust port)
39.9
3/5 E 3/5 E
2 B2 B2 B2 B2 B
21
19.5
LOCK
B A B A 4 A4 A4 A4 A4 A
14 A 14 A
1 P 1 P
FREE
Note 2) Refer to the below pages for L2 dimensions and other dimensions
that are not specified in each wiring specification.
D-sub connector <IP40> : P. 86
D-sub connector <IP67> : P. 89
60
Valve
Plug-in Type 12/Top Ported
U
SS5Y3-12- Stations D (R)
B
Sub-plate
D side U side
89.3
(For 5 stations) Light/surge voltage suppressor
Plug-in
[PE: Pilot EXH port]
[X: External pilot port]
7.4
16 P = 10.5
(15.3)
(
Push-turn locking slotted type:
Press, then rotate it. )
Applicable tube O.D.: ø4, ø5/32" 4(A) port side : Blue (For rubber seal)
(73.2) : Gray (For metal seal)
2(B) port side : Yellow
5.3 PE PE
LOCK
X X
Metal Base
3/5E B A B A B A B A B A 3/5E
92.6
4A 4A 4A 4A 4A
15
11
60.5
58.5
FREE
(40.9)
1P 1P
31.8
30.2
2B 2B 2B 2B 2B
Plug-in
1.7
One-touch fitting
) C6: 3.6
N7: 7.4
M5 x 0.8
1 P 1 P
(73.8)
3/5 E 2 B2 B2 B2 B2 B 3/5 E
(
4 A4 A4 A4 A4 A
Plug-in
Manifold Exploded View
Note 1) These figures show the “SS5Y3-12F2-05D”.
EX500 : P. 132
One-touch Fittings/
186
Series SY3000/5000/7000
Plug-in Type 12/Top Ported
U
SS5Y5-12- Stations D (R)
B
D side U side
Light/surge voltage suppressor
123.6
(For 5 stations)
PE PE
LOCK
BA BA BA BA B A
3/5 3/5
4A 4A 4A 4A 4A
26.9
113.4
116.7
E E
X X
FREE
1 1
81.2
(61.7)
01 : 16.2
C : 14.5
P P
52.8
47.3
39.5
2B 2B 2B 2B 2B
1 P 1 P
76.9
(69.7)
2 B2 B2 B2 B2 B
3/5 E 3/5 E
4 A4 A4 A4 A4 A
187
Common Dimensions Series SY3000/5000/7000
Valve
Plug-in Type 12/Top Ported
U
SS5Y7-12- Stations D (R)
Sub-plate
B
One-touch fitting
(External pilot) D side U side
[PE: Pilot EXH port] (Light/surge voltage suppressor)
Plug-in
[X: External pilot port]
144.3 Manual override
Applicable tube O.D.: ø6, ø1/4"
85.8
(Slide locking manual override)
(Pitch)
26.1 P = 19
(For 5 stations)
(17.1)
(
Push-turn locking slotted type:
Press, then rotate it. )
4(A) port side: Blue (For rubber seal)
(69.5) 6.2 (6.2) : Gray (For metal seal)
2(B) port side: Yellow
Metal Base
PE PE
LOCK
3/5E B A B A B A B A B A 3/5E
4A 4A 4A 4A 4A
(49.4)
21
128.8
133.2
FREE
22.6
Plug-in
96.7
1P 1P
(77.1)
X X
59.9
(45.5)
46.4
2B 2B 2B 2B 2B
(112.1)
(100.3)
88.8
1 P 1 P
(75.1)
2 B2 B2 B2 B2 B
Plug-in
3/5 E 3/5 E
8.7
4 A4 A4 A4 A4 A
Series SY3000/5000
Type 11
Bottom Ported
···
189
Plug-in Connector Connecting Base Series SY3000/5000
Valve
Sub-plate
SY5000: A, B port size Mounting
Plug-in
(Metric/One-touch fitting) (Inch/One-touch fitting) Nil Direct mounting
Symbol Port size Symbol Port size D DIN rail mounting (With DIN rail)
4 ø4 3 ø5/32" D0 DIN rail mounting (Without DIN rail)
6 ø6 7 ø1/4" D3 For 3 stations Specify a longer rail than the standard length.
8 ø8 9 ø5/16" [The SY5000 valve is now at a mountable length
···
···
Nil For all stations of SY3000 Nil For all stations of SY3000 D24 For 24 stations (manifold block length of 16 mm).]
∗ No symbol needs to be specified when fitting type “CM”, “LM” is selected. Note 1) Only direct mounting is available for Type 11 (Bottom ported).
Metal Base
Note 2) Refer to page 196 to determine the L3 using “Calculation formula” for
the DIN rail length.
Note 3) Refer to page 247 for the fixation of DIN rail mounting type manifold.
SY3000: A, B port size
(Metric/One-touch fitting) (Inch/One-touch fitting)
Plug-in
Symbol Port size Symbol Port size
2 ø2 1 ø1/8"
3 ø3.2 3 ø5/32"
4 ø4 7 ø1/4"
6 ø6 9 ø5/16" Note)
Plug-in
Manifold Exploded View
ide
SS5Y5-M10F1-05D-C86 ···1 set (Type M10 5-station manifold base part no.)
∗SY5200-5U1 ·····················3 sets (2-position double part no.)
Plug Assembly Part No.
One-touch Fittings/
190
Series SY3000/5000
How to Order Valves (With mounting screw) Refer to page 3 for valve specifications.
SY 3 1 0 0 5 1
Base mounted
Rated voltage
Seal type 5 24 VDC Type of mounting screw
0 Rubber seal 6 12 VDC Nil Round head combination screw
1 Metal seal ∗ Only 24 VDC is available for the serial B Hexagon socket head cap screw
transmission type. Round head combination screw
K (Falling-out-prevention type)
Hexagon socket head cap screw
Pilot type Light/surge voltage suppressor H (Falling-out-prevention type)
Nil Internal pilot and common specification ∗ For “K” and “H”, the valve body cover has a drop
R External pilot Symbol With light
Surge voltage Common prevention construction to stop the mounting
suppressor specification screws from falling out when the valve is
Nil — — removed for maintenance etc.
∗ When ordering a valve individually, the base
R — Non-polar
Back pressure check valve U
gasket is not included. Since the base gasket is
attached to the manifold, please order the base
(Built-in valve type) S — Positive
gasket separately if it is needed for maintenance
Nil None Z common service.
H Built-in NS — Negative Refer to page 220 for part numbers of the base
∗ Only rubber seal type. Manifold installed type is NZ common gasket and mounting screw.
available if back pressure check valve is ∗ “B” and “H” cannot be selected for the individual
∗ “Nil” is not available for the SI unit manifold. SUP/EXH spacer assembly, interface regulator
required for the valve with metal seal. Refer to ∗ Only “Z” and “NZ” types are available for with
page 232 for Ordering Example. However, it is or double check spacer assembly with residual
the power saving circuit. Select a valve which is pressure release valve.
not recommended to use the built-in valve type suited to the SI unit output polarity or SI unit
and the manifold installed type at the same time specification when the SI unit is selected.
because it will reduce the flow. Refer to the pages below for details.
∗ The built-in valve type back pressure check EX500: P. 131 EX600: P. 139 EX250: P. 151
valve is not available for the 3-position type. EX260: P. 159 EX126: P. 167 EX120: P. 175
Protective class
class III (Mark: )
191
192
One-touch Fittings/ Type 10, 11, 12 Type 50, 51, 52
Manifold Options Plug-in Connector Connecting Base Plug-in Metal Base Plug-in Sub-plate Valve
Plug Assembly Part No. Manifold Exploded View Manifold Exploded View
Type 10 Plug-in Connector Connecting Base: Plug-in Mixed Mounting Type Manifold
D-sub Connector (IP40/67) Flat Ribbon Cable PC Wiring Terminal Block Box (IP67) Lead Wire (IP67)
Side Ported Circular Connector (IP67) EX500 (IP67) EX600 (IP67) EX250 (IP67) EX260 (IP67) EX126 (IP67) EX120
Series SY5000/7000
Type 11
Bottom Ported
···
193
Plug-in Connector Connecting Base Series SY5000/7000
Valve
SY7000: A, B port size Mounting and Option
Sub-plate
(Metric/One-touch fitting) (Inch/One-touch fitting) Option DIN Rail Option
Symbol Mounting
Symbol Port size Symbol Port size Name plate Station number Nil Direct mounting
6 ø6 7 ø1/4" Nil — — 0 Without DIN rail (with bracket)
Direct
Plug-in
8 ø8 9 ø5/16" AA mounting
3 For 3 stations Specify a longer
10 ø10 11 ø3/8" BA — rail than the total
···
···
D — — length of
12 ø12 Nil For all stations of SY5000
A
DIN rail 24 For 24 stations specified stations.
Nil For all stations of SY5000 mounting
∗ No symbol needs to be specified when fitting type “CM”, “LM” is selected. B —
Note 1) Enter the number of stations inside when it is larger than the
number of valve stations. (Refer to “DIN Rail Option” above.)
Note 2) Only direct mounting is available for Type 11 (Bottom ported).
SY5000: A, B port size
Metal Base
Note 3) Refer to page 196 to determine the L3 using “Calculation formula” for
(Metric/One-touch fitting) (Inch/One-touch fitting) the DIN rail length. (For the SY3000 and SY5000 mixed mounting
Symbol Port size Symbol Port size type)
6 ø6 7 ø1/4" Note 4) The manifold block width is 19 mm for both the SY5000 and SY7000
8 sizes.
ø8 9 ø5/16"
Note 5) Refer to page 247 for the fixation of DIN rail mounting type manifold.
Plug-in
10 ø10 11 ø3/8"
12 ø12
Note) The valve pitch is 19 mm, the same as the SY7000.
∗ No symbol needs to be specified when fitting type “CM”, “LM” is selected.
Example (SS5Y7-M10F1-)
Plug-in
ide
Us
s
on
SS5Y7-M10F1-05D-C128 ··1 set (Type M10 5-station manifold base part no.)
∗SY7200-5U1 ·····················3 sets (2-position double part no.)
∗SY5200-5U1 ·····················2 sets (2-position double part no.)
The asterisk denotes the symbol for assembly.
Plug Assembly Part No.
• The valve arrangement is numbered as the 1st station from the D side.
• Under the manifold part number, state the valves to be mounted in order from
the 1st station as shown in the figure above. If the arrangement becomes
complicated, specify on a manifold specification sheet.
Note) When mixing top ported configurations, select from page 202.
In this case, use caution as there is also output on the A and B port on base
Manifold Options
side.
Specify on a manifold specification sheet if plugs are required on the A and B
port on base side.
Protective class
class III (Mark: )
194
Series SY5000/7000
How to Order Valves (With mounting screw) Refer to page 3 for valve specifications.
SY 7 1 0 0 5 1
Base mounted
Rated voltage
Seal type 5 24 VDC Type of mounting screw
0 Rubber seal 6 12 VDC Nil Round head combination screw
1 Metal seal ∗ Only 24 VDC is available for the serial B Hexagon socket head cap screw
transmission type. Round head combination screw
K (Falling-out-prevention type)
Hexagon socket head cap screw
Pilot type Light/surge voltage suppressor H (Falling-out-prevention type)
Nil Internal pilot and common specification
∗ For “K” and “H”, the valve body cover has a drop
R External pilot Symbol With light
Surge voltage Common prevention construction to stop the mounting
suppressor specification screws from falling out when the valve is
Nil — — removed for maintenance etc.
R — Non-polar ∗ When ordering a valve individually, the base
Back pressure check valve U gasket is not included. Since the base gasket is
(Built-in valve type) attached to the manifold, please order the base
S —
Positive gasket separately if it is needed for maintenance
Nil None Z common service.
H Built-in NS — Negative Refer to page 220 for part numbers of the base
∗ Only rubber seal type. Manifold installed type is NZ common gasket and mounting screw.
available if back pressure check valve is ∗ “Nil” is not available for the SI unit manifold. ∗ “B” and “H” cannot be selected for the individual
required for the valve with metal seal. Refer to ∗ Only “Z” and “NZ” types are available for with SUP/EXH spacer assembly, interface regulator
page 232 for Ordering Example. However, it is the power saving circuit. Select a valve which is or double check spacer assembly with residual
not recommended to use the built-in valve type suited to the SI unit output polarity or SI unit pressure release valve.
and the manifold installed type at the same time specification when the SI unit is selected.
because it will reduce the flow. Refer to the pages below for details.
∗ The built-in valve type back pressure check EX500: P. 131 EX600: P. 139 EX250: P. 151
valve is not available for the 3-position type and EX260: P. 159 EX126: P. 167 EX120: P. 175
the SY7000.
Protective class
class III (Mark: )
195
Plug-in Connector Connecting Base Series SY3000/5000/7000
Valve
Plug-in Type 10/Side Ported
U
SS5Y5-M10- Stations D D side
(L5) L1
U side
Manual override
Sub-plate
B
Plug-in
2(B) port side : Yellow
5.5
LOCK
B A B A B A B A B A
35
14 A 14 A 14 A 14 A 14 A
97.5
113.4
FREE
81.2
Metal Base
12 B 12 B
(61.7)
61.7
5.5
12 B 12 B
10.9
4 x M5
Plug-in
4.7
(5.9)
(8.3)
mounting hole
21.9 L2 1.5 (Fitting for the type with P
and E ports on both sides)
5.3 (L4)
(DIN rail mounting hole pitch: 12.5)
(L3)
(SY3000)
(SY3000)
11.1
31.5
78.9
1 P 1 P
4 A4 A
12.4
14.1
(SY5000 and SY3000: ø8, ø5/16")
29.1
(SY5000 and SY3000: ø8, ø5/16")
(11.8)
One-touch fitting 35.9 18 (20.5) (For DIN rail mounting)
(7.5)
Plug-in
P = 12.5
Calculation formula for dimensions with
D-sub connector <IP40>, Flat ribbon cable and PC wiring
L1 = 12.5 x n1 + 16 x n2 + 76.4
L2 = 12.5 x n1 + 16 x n2 + 48
( Pitch of SY3000: ø8,
ø5/16"
P = 16
) One-touch fitting
[4(A), 2(B)port]
serial transmission
One-touch Fittings/
Coefficient a b c
L1 = 12.5 x n1 + 16 x n2 + a + b x n3
L2 = 12.5 x n1 + 16 x n2 x 48 D-sub connector <IP67> 90.5 — —
M = L1/12.5 + 1 Decimal fractions are truncated. Terminal block box or Serial transmission: EX126 149.3 — —
L3 = 12.5 x M + 23
L4 = L3 – 10.5 Lead wire or Circular connector 97 — —
L5 = (L3 – L1)/2 Serial transmission: EX500 88.5 — —
L6 = b x n3 + c
Manifold Options
U
SS5Y7-M10- Stations D
B D side U side Manual override
(DIN rail)
LOCK
B A B A B A B A B A
14 A 14 A 14 A 14 A 14 A
128.8
115
SY5000: 95.7
SY7000: 96.7
FREE
(5.5)
(35)
(77.1)
12 B 12 B 12 B
12 B 12 B
5.5
8.8
3.9
(6)
(9.3)
4 x M5 mounting hole
1 P 1 P
2 B2 B2 B2 B2 B
3/5
11.1
3/5 E E
8.7
35.2
31.6
4 A4 A4 A4 A4 A
14.2
(10)
(21.7)
mounting)
(14.3)
Valve
Plug-in Type 11/Bottom Ported
U L1 U side
SS5Y5-M11- Stations D D side
Sub-plate
B Manual override
Plug-in
2(B) port side : Yellow
LOCK
B A B A B A B A B A
14 A 14 A 14 A 14 A 14 A
97.5
113.4
FREE
81.2
12 B 12 B
Metal Base
5.5
12 B 12 B
10.9
21.9 L2 1.5
Plug-in
(Station 1) --------- (Station n)
Compatible with mixed
mounting type: ø8, ø5/16"
Panel fitting dimensions
SY3000
manual override)
97.5
4.7
(SY3000)
(12.9)
(SY5000)
(7.3)
(9.5)
35.9 18 (20.5)
ø8, ø5/16"
31.8
SY3000:
(SY3000)
L1 = 12.5 x n1 + 16 x n2 + a + b x n3
39.7
Plug-in
2 B2 B2 B
L6 = b x n3 + c
) (
18
2 B2 B
Fitting dimensions for panel mounting
n1: Number of valve stations of the SY3000
(
ø8, ø5/16"
11
Note) Refer to pages 142 and 143 for dimen- One-touch fitting
sions of the EX600 serial transmission
(
Serial transmission: EX600 (M12 connector) 141.5 47 81.5 and built-in silencers.
Serial transmission: EX600 (7/8 inch connector) 158 47 81.5
Serial transmission: EX250 141.5 21 81.5
Serial transmission: EX260 88.7 — —
Serial transmission: EX120 84.7 — —
198
Series SY3000/5000/7000
U
SS5Y7-M11- Stations D D side
L1
U side
B
Manual override
LOCK
B A B A B A B A B A
14 A 14 A 14 A 14 A 14 A
128.8
115
SY5000: 95.7
SY7000: 96.7
FREE
12 B 12 B 12 B
12 B 12 B
5.5
8.8
(Station 1) (Station n)
2
16
85.8
82.7
56.6
9.1
60
115
(12)
(14.5)
(23.9)
48.7
3/5 E 3/5 E
2 B2 B2 B2 B2 B
21
19.5
4 A4 A4 A4 A4 A
1 P 1 P
Note 1) Refer to page 185 for dimensions of external pilots and built-in silencers.
Note 2) Refer to the below pages for L1, L2 dimensions and other dimensions One-touch fitting (For SY7000) One-touch fitting (For SY5000)
that are not specified in each wiring specification. [4(A), 2(B) port] [4(A), 2(B) port]
Dimensions of Type 11/Bottom ported : P. 185 Applicable tube O.D.: ø6 ,ø1/4" Applicable tube O.D.: ø6 ,ø1/4"
: ø8 ,ø5/16" : ø8 ,ø5/16"
D-sub connector <IP40> : P. 86
: ø10,ø3/8" : ø10,ø3/8"
D-sub connector <IP67> : P. 89 : ø12 : ø12
Flat ribbon cable : P. 92
Terminal block box : P. 104
Lead wire : P. 114
Circular connector : P. 124
EX500 : P. 134
EX600 : P. 144, 145
EX250 : P. 154
EX260 : P. 162
EX126 : P. 170
199 EX120 : P. 178
200
One-touch Fittings/ Type 10, 11, 12 Type 50, 51, 52
Manifold Options Plug-in Connector Connecting Base Plug-in Metal Base Plug-in Sub-plate Valve
Plug Assembly Part No. Manifold Exploded View Manifold Exploded View
Plug-in Connector Connecting Base: Plug-in Mixed Mounting Type Manifold
D-sub Connector (IP40/67) Flat Ribbon Cable PC Wiring Terminal Block Box (IP67) Lead Wire (IP67)
Circular Connector (IP67) EX500 (IP67) EX600 (IP67) EX250 (IP67) EX260 (IP67) EX126 (IP67) EX120
Series SY3000/5000/7000
Type 12
Top Ported
For the SY5000 series, the SY5000 and the SY3000
can be mounted on the same manifold.
For the SY7000 series, the SY7000 and the SY5000
can be mounted on the same manifold. How to Order Manifold
Refer to pages 187 and 188
for dimensions of Type
12/Top ported type.
SS5Y 5 M 12 F 1 05 U
Mixed Mounting Type
For the SY5000 series, it is possible to mount the SY3000 size valves on all
stations. However, the SY3000 manifold block width should be 12.5 mm.
(16 mm for ø8 or ø5/16" One-touch fitting)
Also, for the SY7000 series, it is possible to mount the SY5000 size valves on
all stations. However, the SY3000 cannot be mounted onto the SY7000 series.
···
···
to the pages shown in the table
P 26 pins 24 24 stations “Connector type” for details.
• With Lead wire PG Flat ribbon cable 20 pins 93
PH 10 pins
Lead wire length J PC wiring —
1 0.6 m G (20 pins) With power supply terminal
P, E port entry
2 1.5 m T Terminal block box 105 U Note) U side (2 to 10 stations)
3 3m L1 34 cores D Note) D side (2 to 10 stations)
L2 Lead wire 17 cores 115 B Both sides (2 to 24 stations)
• With D-sub connector (IP40/67), Flat L3 9 cores ∗ Refer to page 147 for the EX600 and on page
ribbon cable and PC wiring M Circular connector 125 155 for the EX250.
Connector entry direction S EX500 135 Note) For type “S”, supply/exhaust block assembly
with built-in silencer, choose U or D for P
1 Upward S6 EX600 147
port entry.
2 Lateral S Serial EX250 155
S transmission EX260 163
∗ It is not necessary to select the items above for S4 EX126 171 SUP/EXH block assembly
the valve with terminal block box or with circular
S3 EX120 179 Nil Internal pilot
connector or the serial transmission type.
∗ Refer to the pages shown in the table above for details. S Internal pilot, Built-in silencer
How to Order Manifold Assembly R External pilot
∗ For built-in silencer type, P and E ports are
available on U and D sides. 3/5(E) port is
Example (SS5Y5-M12F1-) plugged. The silencer exhaust port is located on
the opposite side of P, E port entry. (Example:
2-position double 2-position double
When the P, E port entry is D side, the silencer
SY5230-5U1-C8 (3 sets) SY3230-5U1-C6 (2 sets) exhaust port is U side.)
∗ Refer to page 147 for the EX600 and on page
Manifold base (5 stations) 155 for the EX250.
SS5Y5-M12F1-05D
P, E port size
(One-touch fittings)
e
Symbol SY5000 SY7000 Note
U sid Nil ø10 ø12 Metric size
s
ati
on N ø3/8" ø1/2" Inch size
St
3
2
ide
1
Mounting
Ds
Nil Direct mounting
SS5Y5-M12F1-05D ···1 set (Type M12 5-station manifold base part no.) D DIN rail mounting (With DIN rail)
∗SY5230-5U1-C8 ········3 sets (2-position double part no.) D0 DIN rail mounting (Without DIN rail)
∗SY3230-5U1-C6 ········2 sets (2-position double part no.) D3 For 3 stations Specify a longer rail than the standard
length. [For the SS5Y5-M12, the SY5000
The asterisk denotes the symbol for assembly.
···
···
Valve
How to Order Valves (With mounting screw) Refer to page 3 for valve specifications.
SY 3 1 3 0 5 1 C6
Sub-plate
Plug-in
Top ported
Metal Base
periods of time. 02 1/4 SY7000
∗ Be careful of the energizing time when the
Type of actuation power saving circuit is selected. Refer to page One-touch fitting (Metric)
1 Single 244 for details. Symbol A, B port SY3000 SY5000 SY7000
2-position
2 Double C2 ø2 — —
3
Plug-in
Closed center Rated voltage C3 ø3.2 — —
4 3-position Exhaust center C4 ø4 —
5 24 VDC
5 Pressure center C6 ø6
6 12 VDC
A∗ N.C./N.C. C8 ø8 —
4-position ∗ Only 24 VDC is available for the serial
B∗ dual 3-port
N.O./N.O. C10 ø10 — —
transmission type.
C∗ N.C./N.O. C12
Plug-in
Nil None EX500: P. 136 EX600: P. 148 EX250: P. 156
H Built-in EX260: P. 164 EX126: P. 172 EX120: P. 180 Type of mounting screw
∗ Only rubber seal type. Manifold installed type is Nil Round head combination screw
202
Series SY3000/5000/7000
U
SS5Y5-M12- Stations D D side U side
B
(L5) L1
( Pitch of
SY5000 ) Manual override
Light/surge voltage suppressor
32.8 21.1 P = 16
(
Push-turn locking slotted type:
Press, then rotate it. )
78.9
(Slide locking manual override)
(
Pitch of
SY3000 ) 4(A) port side : Blue (For rubber seal)
: Gray (For metal seal)
P = 12.5
2(B) port side : Yellow
(8)
PE
LOCK
3/5 B A B A B A B A B A
(5.5)
(35)
4A 4A
4A 4A 4A
113.4
E
26.5
FREE
X
1
(SY3000)
81.2
(SY3000)
2B 2B
(61.7)
(SY5000)
11
01 : 16.2
C: 14.5
(SY5000)
56.4
P
47.3
39.5
2B 2B 2B
2.7
4.7
One-touch fitting
[1(P), 3/5(E) port] One-touch fitting One-touch fitting
Applicable tube O.D.: ø10, ø3/8" [4(A), 2(B) port] [4(A), 2(B) port]
Applicable tube O.D.: ø4, ø5/32" Applicable tube O.D.: ø2
: ø6, ø1/4" : ø3.2, ø1/8"
: ø8, ø5/16" : ø4, ø5/32"
5.3 L4 : ø6, ø1/4"
(DIN rail mounting hole pitch: 12.5)
L3
(SY3000)
(91.3)
and PC wiring 2 B2 B2 B2 B2 B
mounting)
(11.8)
L5 = (L3 – L1 + 6.1)/2
n1: Number of valve stations of the SY3000
n2: Number of valve stations of the SY5000
Calculation formula for dimensions with D-sub Note) Refer to page 182 for dimensions of
connector <IP67>, Terminal block box, Lead wire, external pilot and elbow fittings.
Circular connector, EX500/600/250/260/126/120
serial transmission
L1 = 12.5 x n1 + 16 x n2 + a + b x n3
L2 = 12.5 x n1 + 16 x n2 x 48
M = L1/12.5 + 1 Decimal fractions are truncated.
L3 = 12.5 x M + 23 Coefficient a b c
L4 = L3 – 10.5 D-sub connector <IP67> 90.5 — —
L5 = (L3 – L1)/2 Terminal block box or Serial transmission: EX126 149.3 — —
L6 = b x n3 + c Lead wire or Circular connector 97 — —
n1: Number of valve stations of the SY3000 Serial transmission: EX500 88.5 — —
n2: Number of valve stations of the SY5000 Serial transmission: EX600 (M12 connector) 141.5 47 81.5
n3: Number of I/O units or input block stations
Serial transmission: EX600 (7/8 inch connector) 158 47 81.5
Note) Refer to pages 142 and 143 for dimensions of the
Serial transmission: EX250 141.5 21 81.5
EX600 serial transmission with I/O unit and page 153
for the EX250 serial transmission with input block Serial transmission: EX260 88.7 — —
when L6, b and c are used for the calculation formula. Serial transmission: EX120 84.7 — —
203
Plug-in Connector Connecting Base Series SY3000/5000/7000
Valve
Plug-in Type 12/Top Ported
U
SS5Y7-M12- Stations D
Sub-plate
B
D side U side
L1
Plug-in
Manual override
One-touch fitting
[1(P), 3/5(E) port]
Applicable tube O.D.: ø12, ø1/2"
33.9
(Pitch)
26.1 P = 19
(Pitch)
P = 19 42.2 (
Push-turn locking slotted type:
Press, then rotate it. )
4(A) port side: Blue (For rubber seal)
85.8 : Gray (For metal seal)
(Slide locking manual override) 2(B) port side: Yellow
Metal Base
PE
LOCK
3/5E B A B A B A B A B A
4A 4A 4A 4A 4A
21
128.8
FREE
SY5000: 95.7
SY7000: 96.7
Plug-in
(SY5000)
C: 14.5
01: 16.2
1P
(SY5000)
77.1
(SY7000)
(SY7000)
X 2B 2B 2B
22.6
61.8
59.9
57.7
2B 2B
4 x M5 mounting hole
1/4 [A(A), 2(B) port]
[A(A), 2(B) port]
20.7 L2 1.5
(DIN rail mounting hole pitch: 12.5) One-touch fitting (For SY5000)
One-touch fitting (For SY7000) [4(A), 2(B) port]
[4(A), 2(B) port] Applicable tube O.D.: ø4, ø5/32"
Applicable tube O.D.: ø6 , ø1/4" : ø6, ø1/4"
: ø8 , ø5/16" (Station 1) (Station n) : ø8, ø5/16"
: ø10, ø 3/8"
(SY7000)
(SY5000)
(100.3)
(SY7000)
(98.2)
(SY5000)
Plug-in
88.8
83.8
1 P 1 P
(75.1)
2 B2 B2 B2 B2 B
3/5 E 3/5 E
4 A4 A4 A4 A4 A
Note 1) Refer to page 183 for dimensions of external pilot and elbow fittings.
Plug Assembly Part No.
Note 2) Refer to the below pages for L1, L2, L3, L4 dimensions and other
One-touch Fittings/
Valve
Connector Connecting Base Manifold Exploded View
Manifold Exploded View Page 219 U side
Sub-plate
Plug-in
D side
Metal Base
Plug-in
LOC
K
FRE
E
Wiring
Plug-in
Manifold Exploded View
Type 10, 11, 12
Lead wire Circular connector EX500 EX600
Page 210 Page 211 Page 212 Page 213
206
Series SY3000/5000/7000
Wiring
D-sub Connector <IP40>/Flat Ribbon Cable Manifold exploded view
q
U side
Locking bracket
(For D-sub connector)
LOC
Cover assembly K
Holding screw
D side
w Clamp bracket assembly
It is mounted only for the DIN rail mounting type. Refer to pages 219 to 222
The holding screw of the clamping bracket is for details about common parts.
tightened at one point.
(Tightening torque of holding screw: 10.3 lbf·ft (1.4 N·m))
Side ported
Nil — — L10 ø10 — — Metric size
S — Side L12 ø12 — —
R — — LN9 ø5/16" — —
Side ported
V — — LN11 ø3/8" — — Inch size
RV — — Top LN13 ø1/2" — —
VP — ∗ B8 ø8 — —
Side ported
B — — B10 ø10 — — Metric size
BS — Bottom B12 ø12 — —
BR — — BN9 ø5/16" — —
Side ported
∗ For silencer (supply side). E port is BN11 ø3/8" — — Inch size
plugged. BN13 ø1/2" — —
Note) “B” for bottom ported can be 00 Note 1) Plug P/E port entry on one
selected for the SY5000/7000 00U Note 2) Plug side or Top ported
series. Note 1) It can be selected only if no symbol or “S” or “V” or “B” is
SUP/EXH block assembly (D side) selected for the pilot and the piping.
accessories and the number of accessories Note 2) “00U” is available only for the D-sub connector type and it has
an inch size locking bracket.
Accessories SY3000 SY5000
SY7000
a Tension bolt None Note) 3 pcs.
Note) Since the nuts are embedded in the SUP/EXH block.
207
Type 10, 11, 12
Connector Connecting Base Manifold Exploded View Series SY3000/5000/7000
Valve
Wiring
D-sub Connector <IP67> Manifold exploded view
q
U side
Sub-plate
w
Plug-in
Locking a
bracket Tension
bolt
Mounting screw
(Tightening torque:
Metal Base
0.59 lbf·ft (0.8 N·m))
D side
Holding screw
Refer to pages 219 to 222
e Clamp bracket assembly for details about common parts.
Plug-in
It is mounted only for the DIN rail mounting type.
The holding screws of the clamping bracket is
tightened at two points.
(Tightening torque of holding screw: 10.3 lbf·ft (1.4 N·m))
Plug-in
— —
R — — LN9 ø5/16" — —
V — — Side ported
LN11 ø3/8" — — Inch size
RV — — Top LN13 ø1/2" — —
∗
a
Tension
bolt
Mounting screw
DIN rail holding screw (Tightening torque: 10.3 lbf·ft (1.4 N·m))
(Tightening torque: 10.3 lbf·ft (1.4 N·m))
SY30M 15 4A SY3000
SY5000/7000
SY30M-15-1A
SY50M-15-1A
∗ Part number is for one assembly.
∗ Part number is for one assembly.
209
Type 10, 11, 12
Connector Connecting Base Manifold Exploded View Series SY3000/5000/7000
Valve
Wiring
Lead Wire Manifold exploded view
q
U side
Sub-plate
w
Plug-in
a
Tension
bolt
Mounting screw
Metal Base
(Tightening torque:
0.59 lbf·ft (0.8 N·m)) D side
Plug-in
e Clamp bracket assembly
It is mounted only for the DIN rail mounting type.
The holding screws of the clamping bracket is
tightened at two points.
(Tightening torque of holding screw: 10.3 lbf·ft (1.4 N·m))
Manifold Parts No.
Plug-in
BS — Bottom LN11 ø3/8" — —
Side ported
BR — — Inch size
LN13 ø1/2" — —
∗ For silencer (supply side). E port is B8 ø8 — —
plugged. Side ported
SY30M 14 4A
Number of cores Lead wire length (m)
1 34 1 0.6
2 17 2 1.5
Manifold Options
3 9 3 3
q
U side
a
Tension
bolt
Mounting screw
(Tightening torque:
0.59 lbf·ft (0.8 N·m)) D side
211
Type 10, 11, 12
Connector Connecting Base Manifold Exploded View Series SY3000/5000/7000
Valve
Wiring
EX500 Manifold exploded view
Sub-plate
U side
Plug-in
a
Tension
bolt
Mounting screw
(Tightening torque:
Metal Base
0.59 lbf·ft (0.8 N·m))
D side
Plug-in
It is mounted only for the DIN rail mounting type.
The holding screws of the clamping bracket is
tightened at two points.
(Tightening torque of holding screw: 1.03 lbf·ft (1.4 N·m))
Plug-in
— Bottom Side ported
LN11 ø3/8" — — Inch size
BR — —
LN13 ø1/2" — —
∗ For silencer (supply side). E port is B8 ø8 — —
plugged. Side ported
B10 ø10 — —
w EX500 SI unit
One-touch Fittings/
EX500 Q 0 01
Output specifications
0 NPN (Positive common)
1 PNP (Negative common)
Manifold Options
Mounting screw q
(Tightening torque: 0.59 lbf·ft (0.8 N·m)) U side
w
e
a
Tension
t bolt
D side
Holding screw
Valve
Manifold Parts No.
t EX600 digital input unit
Sub-plate
EX600 DX P B
Input type Number of inputs, open circuit detection, and connector
Symbol Description Symbol Number of inputs Open circuit detection Connector
Plug-in
P PNP B 8 No M12 connector (5 pins) 4 pcs.
N NPN C 8 No M8 connector (3 pins) 8 pcs.
C1 8 Yes M8 connector (3 pins) 8 pcs.
D 16 No M12 connector (5 pins) 8 pcs.
E 16 No D-sub connector (25 pins) Note 1) 2)
F 16 No Spring type terminal block (32 pins) Note 1) 2)
Metal Base
EX600 DY P B
Output type Number of outputs and connector
Symbol Description Symbol Number of outputs Connector
P PNP B 8 M12 connector (5 pins) 4 pcs.
Plug-in
N NPN E 16 D-sub connector (25 pins) Note 1) 2)
F 16 Spring type terminal block (32 pins) Note 1) 2)
Plug-in
EX600 AM B
Analog input/output Number of input/output channels and connector
EX600 ZMA3
Enclosed parts
Round head screw with washer (M4 x 20) 1 pc.
P-tight screw (4 x 14) 2 pcs. Note 1) Cannot be communicated with the EX600-HT1- (Old version of the Handheld Terminal).
Note 2) Cannot be connected with the EX600-SPR1, EX600-SPR2, EX600-SDN1, or EX600-SDN2.
214
Series SY3000/5000/7000
Wiring
EX250 Manifold exploded view
q
U side
w
r a
Tension
t bolt
y
Holding screw D side
Valve
Wiring
EX260 Manifold exploded view
q U side
Sub-plate
a
Plug-in
Tension
bolt
Holding screw
e Clamp bracket assembly
It is mounted only for the DIN rail mounting type. D side Refer to pages 219 to 222
Metal Base
The holding screws of the clamping bracket is tightened
for details about common parts.
at two points. (Tightening torque of holding screw: 1.03 lbf·ft (1.4 N·m))
Plug-in
qSUP/EXH block assembly
Mounting
SY 3 0M 1 1A C8 Nil Direct mounting
D0 DIN rail mounting (Without DIN rail)
Series
∗ For bottom ported, the symbol is nil.
3 SY3000
Plug-in
P/E port entry on one
00 Note) Plug
EX260 S PR1
side or Top ported
Note) It can be selected only if no symbol or “S” or “V” or “B” is
NCN EAN
32 32
PR6 Sink/NPN (Positive common) NC EN2 EtherNet/IP™ Sink/NPN (Positive common) EA
Source/PNP (Negative common) D-sub M12
Note)
PR7 16
NDN EN3 16
Source/PNP (Negative common) EBN
PR8 Sink/NPN (Positive common) ND EN4 Sink/NPN (Positive common) EB
MJ1 32
Source/PNP (Negative common) VAN
MJ2 CC-Link
Sink/NPN (Positive common)
M12
VA
MJ3 16
Source/PNP (Negative common) VBN
MJ4
Manifold Options
q
U side
w
a
Tension
bolt
e
Valve
Wiring
EX120 Manifold exploded view
q
U side
Sub-plate
w
Plug-in
a
Tension
bolt
Metal Base
D side
Plug-in
The holding screw of the clamping bracket is
tightened at one point.
(Tightening torque of holding screw: 1.03 lbf·ft (1.4 N·m))
Plug-in
LN11 ø3/8" — —
BR — —
LN13 ø1/2" — —
Inch size
∗ For silencer (supply side). E port is plugged. B8 ø8 — —
Note) “B” for bottom ported can be selected for Side ported
B10 ø10 — —
Communication protocol
DN1 DeviceNet™ (Positive common)
CS1 OMRON Corp.: CompoBus/S (16 outputs) (Positive common)
CS2 OMRON Corp.: CompoBus/S (8 outputs) (Positive common)
MJ1 CC-Link (Positive common)
Manifold Options
u DIN rail
It is mounted only for
the DIN rail mounting
type (with DIN rail.)
A Manifold block
assembly
D side Details Page 221
EXH blocking disk assembly
t Refer to “Manifold Options”
Tie-rod on page 231. Holding screw
(SY5000/7000: 3 pcs.)
i Clamp bracket assembly
It is mounted only for the DIN
rail mounting type. (Tightening
∗ The figures show the SY3000 series. torque of holding screw: 1.03 lb·ft (1.4 N·m))
1 Loosen the U-side tension bolt a, and remove the B <For SY3000>
SUP/EXH end block assembly.
Caution
1. Be sure to shut off the power and air supplies before Gaskets are mounted.
disassembly.
Furthermore, since air may remain inside the actuator, piping ∗ Manifold block assembly
and manifold, confirm that the air is completely exhausted No. Description Q'ty Note
before performing any work. For base, connector
qwe Gasket 3
2. When disassembly and assembly are performed, air leakage and manifold block
may result if the tightening of the tension bolt is inadequate.
Tie-rod for SY3000 2 pcs.
r additional stations SY5000 3 pcs.
SY7000 3 pcs.
Refer to page 220 for ordering single unit.
219
Type 10, 11, 12
Connector Connecting Base Manifold Exploded View Series SY3000/5000/7000
Valve
For SS5Y3-10/11/12, SS5Y5-(M)10/11/12, SS5Y7-(M)10/11/12
Sub-plate
Base gasket Part numbers shown on the left are
A-q
(for connector connecting base) SY30M-9-1A SY50M-9-1A SY70M-9-1A for 10 valves. (10 pcs.)
Manifold block assembly
Plug-in
A-e Supplied individually.
Note 2)
2 pcs. supplied (SY3000),
SY3000/5000/7000 SY30M-49-2-A SV2000-55-2A-A SY70M-49-2-A 3 pcs. supplied (SY5000/7000)
stations Note 1)
Tie-rod for
additional
Metal Base
: Manifold stations (2 stations to 24
SY3000/5000/7000 VVQC1000-TR- SV2000-55-1--A SY70M-49-1--A stations) 2 pcs. supplied (SY3000),
t Tie-rod 3 pcs. supplied (SY5000/7000)
Mixed mounting type manifold
(for mounting only SY3000 on — SY50M-49-1--A SY70M-49-1--A 3 pcs. supplied.
Plug-in
SY5000 manifolds)
220
Series SY3000/5000/7000
Manifold Parts No.
AManifold block assembly
SY 3 0M 2 1 D A C6
Series A, B port size (One-touch fittings)
3 SY3000 Symbol A, B port SY3000 SY5000 SY7000 Note Symbol A, B port SY3000 SY5000 SY7000 Note
5 SY5000 C2 ø2 — — L4 ø4 — Side
7 SY7000 C3 ø3.2 — — Side/ L6 ø6 ported
Upward elbow
C4 ø4 Bottom L8 ø8 — Note) Metric
Piping direction C6 ø6 ported L10 ø10 — — size
1 Side/Top ported C8 ø8 — Note) Metric LN3 ø5/32" — — Side
2 Bottom ported C10 ø10 — — size LN7 ø1/4" — ported
Note) “2” for bottom ported can
C12 ø12 — — LN9 ø5/16" — Note) — Inch
be selected for the
N1 ø1/8" — — Side/ LN11 ø3/8" — — size
SY5000/7000 series.
N3 ø5/32" — Bottom B4 ø4 — Side
Downward elbow
N7 ø1/4" ported B6 ø6 ported
N9 ø5/16" — Note) Inch B8 ø8 — Note) Metric
N11 ø3/8" — — size B10 ø10 — — size
Note) Refer to mixed mounting type for ø8, ø5/16". BN3 ø5/32" — — Side
Single wiring BN7 ø1/4" — ported
Marked with ß BN9 ø5/16" — Note) — Inch
BN11 ø3/8" — — size
00 Plug Top ported
Wiring type
S Single wiring
D Double wiring A Manifold (All parts inside are included.)
block assembly
q Base gasket
A Mixed mounting of the SY3000/5000 w Connector r Tie-rod for
gasket
Manifold block assembly for mounting the SY3000 additional
stations
SY50M 2 3 D A C6
Piping direction A, B port size (One-touch fittings)
3 Side/Top ported Symbol A, B port Note Symbol A, B port Note
4 Bottom ported C2 ø2 L4 ø4 Side ported
Downward elbow Upward elbow
Side/Bottom
C3 ø3.2
ported L6 ø6 Metric size
Wiring type C4 ø4 Metric size LN3 ø5/32" Side ported
S Single wiring C6 ø6 LN7 ø1/4" Inch size
D Double wiring N1 ø1/8" Side/Bottom B4 ø4 Side ported
N3 ø5/32" ported B6 ø6 Metric size
N7 ø1/4" Inch size BN3 ø5/32" Side ported
BN7 ø1/4" Inch size
00 Plug Top ported Gaskets are mounted.
Side/Bottom
C8 ø8
ported L8 ø8 Side ported B8 ø8 Side ported
Wiring type C10 ø10 Metric size L10 ø10 Metric size B10 ø10 Metric size
S Single wiring C12 ø12 L12 ø12 B12 ø12
D Double wiring N7 ø1/4" Side/Bottom Side ported Side ported
N9 ø5/16" ported LN11 ø3/8"
Inch size BN11 ø3/8"
Inch size
N11 ø3/8" Inch size 00 Plug Top ported
221
Type 10, 11, 12
Connector Connecting Base Manifold Exploded View Series SY3000/5000/7000
Valve
Manifold Parts No.
B SUP/EXH end block assembly
Sub-plate
SY 3 0M 3 1A C8
Series Mounting
Plug-in
3 SY3000 Nil Direct mounting
5 SY5000 D0 DIN rail mounting (Without DIN rail)
7 SY7000 ∗ For bottom ported, the symbol is nil.
Metal Base
Symbol
Internal External silencer direction
Nil — — B SUP/EXH end block assembly
(Includes a.)
S — Side
R — —
V — —
RV
Plug-in
— — Top
VP — ∗
B — —
BS — Bottom
BR
— —
A-e
a Tension bolt
( )
∗ For silencer (supply side). E port is plugged.
Tightening torque:
Plug-in
Metric size
B12 ø12 — —
BN9 ø5/16" — —
Side ported
BN11 ø3/8" — — Inch size
BN13
222
Series SY3000/5000/7000
Cover assembly
(Internal pilot) SY 3 0M 4 1A
Dent for positioning
X, PE port
1. Be sure to shut off the power and air supplies before SY0M-6-1ARV-.
disassembly.
Furthermore, since air may remain inside the actuator, piping
and manifold, confirm that the air is completely exhausted
before performing any work.
2. When disassembly and assembly are performed, air leakage
may result if the tightening of the cover and port block
assemblies are inadequate.
223
Series SY3000/5000/7000
One-touch Fittings
Valve
and Plug Assembly/Part No.
Refer to “Changing One-touch Fittings” on page 248 for replacement method.
One-touch fittings
Sub-plate
Port size SY3000 SY5000 SY7000
ø2 VVQ1000-50A-C2 — —
ø3.2 VVQ1000-50A-C3 — —
ø4 VVQ1000-50A-C4 VVQ1000-51A-C4 —
Plug-in
ø6 Straight type VVQ1000-50A-C6 VVQ1000-51A-C6 VVQ2000-51A-C6
ø8 — VVQ1000-51A-C8 VVQ2000-51A-C8
ø10 — — VVQ2000-51A-C10
ø12 — — KQ2H12-17-X224
Metric size
ø4 SZ3000-73-1A-L4 SZ3000-74-1A-L4 —
ø6 SZ3000-73-1A-L6 SZ3000-74-1A-L6 SZ3000-83-1A-L6
ø8 Elbow type — SZ3000-74-1A-L8 SZ3000-83-1A-L8
Metal Base
ø10 — — SZ3000-83-1A-L10
ø12 — — KQ2L12-17N-X224
ø4 SZ3000-73-2A-L4 SZ3000-74-2A-L4 —
A, B port Note1)
Plug-in
ø8 Long elbow type — SZ3000-74-2A-L8 SZ3000-83-2A-L8
ø10 — — SZ3000-83-2A-L10
ø12 — — KQ2W12-17N-X224
ø1/8" VVQ1000-50A-N1 — —
ø5/32" KJL03-95-X224 — —
ø1/4" KJL07-95-X224 KQ2L07-14-X224 —
Elbow type
ø5/16" — KQ2L09-14-X224 —
ø3/8" — — KQ2L11-14-X224
ø8 SZ3000-74-1A-L8 — —
Plug-in
ø10 Elbow type — SZ3000-83-1A-L10 —
ø12 — KQ2L12-19N-X224
ø8 SZ3000-74-2A-L8 — —
ø12 — — KQ2W12-19N-X224
ø5/16" VVQ1000-51A-N9 — —
ø3/8" Straight type — VVQ2000-51A-N11 —
ø1/2" — — VVQ4000-50B-N13
Inch size
ø5/16" KQ2L09-14-X224 — —
ø3/8" Elbow type — KQ2L11-14-X224 —
ø1/2" — — KQ2L13-19N-X224
Plug Assembly Part No.
One-touch Fittings/
ø5/16" KQ2L09-14-X225 — —
ø3/8" Long elbow type — KQ2L11-14-X225 —
ø1/2" — — KQ2W13-19N-X224
Note 1) A and B ports (ø8 and ø5/16") of the SY3000 and 5000 mixed mounting type are the same as those of the SY5000.
Note 2) The basic order unit of the One-touch fitting part number is 1 pc. Additionally, when performing the piping in the same orientation using the elbow type,
please order “elbow type” or “long elbow type” appropriately.
Manifold Options
Plug assembly
SY3000 SY5000 SY7000
A, B port VVQ0000-58A VVQ1000-58A VVQ2000-58A
P, E port VVQ1000-58A VVQ2000-58A SY9000-62-1A
Note) The basic order unit of the plug assembly part number is 1 pc.
224
Series SY3000/5000/7000
Manifold Options
DIN rail dimensions/weight for the SY3000 Plug-in metal base and
the SY3000/5000 Plug-in connector connecting base
VZ1000-11-1-
∗ After confirming the L3 dimension in the dimensions table of each series, refer to the DIN rail dimensions table below and
specify the number in the box .
L
8 (7.5)
5.5
(35)
(25)
Rail mounting hole pitch 12.5
No. 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18
L dimension 98 110.5 123 135.5 148 160.5 173 185.5 198 210.5 223 235.5 248 260.5 273 285.5 298 310.5 323
Weight (g) 17.6 19.9 22.1 24.4 26.6 28.9 31.1 33.4 35.6 37.9 40.1 42.4 44.6 46.9 49.1 51.4 53.6 55.9 58.1
No. 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37
L dimension 335.5 348 360.5 373 385.5 398 410.5 423 435.5 448 460.5 473 485.5 498 510.5 523 535.5 548 560.5
Weight (g) 60.4 62.5 64.9 67.1 69.4 71.6 73.9 76.1 78.4 80.6 82.9 85.1 87.4 89.6 91.9 94.1 96.4 98.6 100.9
No. 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56
L dimension 573 585.5 598 610.5 623 635.5 648 660.5 673 685.5 698 710.5 723 735.5 748 760.5 773 785.5 798
Weight (g) 103.1 105.4 107.6 109.9 112.1 114.4 116.6 118.9 121.1 123.4 125.6 127.9 130.1 132.4 134.6 136.9 139.1 141.4 143.6
No. 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71
L dimension 810.5 823 835.5 848 860.5 873 885.5 898 910.5 923 935.5 948 960.5 973 985.5
Weight (g) 145.9 148.1 150.4 152.6 154.9 157.1 159.4 161.6 163.9 166.1 168.4 170.6 172.9 175.1 177.4
DIN rail dimensions/weight for the SY5000/7000 Plug-in metal base and
the SY7000 Plug-in connector connecting base
VZ1000-11-4-
∗ After confirming the L3 dimension in the dimensions table of each series, refer to the DIN rail dimensions table below and
specify the number in the box .
L
8
5.5
(35)
(25)
No. 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18
L dimension 98 110.5 123 135.5 148 160.5 173 185.5 198 210.5 223 235.5 248 260.5 273 285.5 298 310.5 323
Weight (g) 24.8 28 31.1 34.3 37.4 40.6 43.8 46.9 50.1 53.3 56.4 59.6 62.7 65.9 69.1 72.2 75.4 78.6 81.7
No. 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37
L dimension 335.5 348 360.5 373 385.5 398 410.5 423 435.5 448 460.5 473 485.5 498 510.5 523 535.5 548 560.5
Weight (g) 84.9 88 91.2 94.4 97.5 100.7 103.9 107 110.2 113.3 116.5 119.7 122.8 126 129.2 132.3 135.5 138.6 141.8
No. 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56
L dimension 573 585.5 598 610.5 623 635.5 648 660.5 673 685.5 698 710.5 723 735.5 748 760.5 773 785.5 798
Weight (g) 145 148.1 151.3 154.5 157.6 160.8 163.9 167.1 170.3 173.4 176.6 179.8 182.9 186.1 189.2 192.4 195.6 198.7 201.9
No. 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71
L dimension 810.5 823 835.5 848 860.5 873 885.5 898 910.5 923 935.5 948 960.5 973 985.5
Weight (g) 205.1 208.2 211.4 214.5 217.7 220.9 224 227.2 230.4 233.5 236.7 239.8 243 246.2 249.3
225
Manifold Options Series SY3000/5000/7000
Valve
Caution
Tightening torque for mounting screw
M2: 0.12 lbf ft (0.16 N·m) (SY3000)
Manifold Options ∗ Refer to pages 236, 238, 240 for dimensions. M3: 0.59 lbf ft (0.8 N·m) (SY5000/7000)
Sub-plate
[With two mounting screws (3 pcs. for the SY7000)]
Used when valve additions are expected or for maintenance. A SY 3 0M 26 1 A
structure is in place on the blanking plate to prevent the mounting
screws from sliding. Mounting Series Option for mounting
Mounting screw
Mounting 3 SY3000 With mounting screw
Plug-in
screw (3 pcs.) Nil
screw 5 SY5000 (Round head combination screw)
(2 pcs.)
(2 pcs.)
7 SY7000 With mounting screw
B (Hexagon socket head cap screw)
(A) (B)
4 2 Base type
1 For plug-in connector connecting base
2 For plug-in metal base
5 1 3
(EA) (P) (EB)
Metal Base
SY30M-26-A (-B) SY50M-26-A (-B) SY70M-26-A (-B) Circuit diagram
Individual SUP spacer assembly How to Order Individual SUP/EXH Spacer Assembly
[With a connector gasket, a base gasket, and two mounting screws (3 One-touch fitting
SY 3 0M 38 1 A C6
Plug-in
pcs. for the SY7000)] Straight type
When the same manifold is used for different pressures, an individual
SUP spacer assembly is used as a supply port for different pressures. One-touch fitting
Note) When selecting a One-touch fitting elbow type for a spacer Elbow type SY 3 0M 38 2 A L6
assembly, use it faced upward, since it interferes with A and B port
piping in Type 50 and Type 10 manifolds.
Series
Plug-in
L4 ø4 —
Individual EXH spacer assembly L6 ø6
[With a connector gasket, a base gasket, and two mounting screws (3 pcs. for L8 ø8 —
the SY7000)] L10 ø10 — —
screw C2 ø2 — —
5(EA)
1(P) C3 ø3 — —
3(EB) C4 ø4 —
Circuit diagram
C6 ø6
(Mounting example of a
2-position single valve) C8 ø8 —
Part numbers of mounting
C10 ø10 — —
Base gasket screw (For repairs) C12 ø12 — —
Manifold Options
Double check spacer assembly with residual pressure release valve (Side/Bottom <Example>
ported) Double check spacer assembly with residual pressure release valve
[With a connector gasket, a base gasket, and two mounting screws (3 pcs. for the SY7000)] 3-position exhaust center valve
It is used to hold the intermediate position of the cylinder for a long period of time. Use a 3-position exhaust
center valve when the double check spacer assembly with residual exhaust valve is used.
It can also be used for drop prevention at the cylinder stroke end when supply residual pressure is released by
using a 2-position single/double valve.
Note) When the elbows are facing upward in A and B ports in Type 10 manifolds, they will interfere with the piping for
the spacer assembly. Therefore, combine the A and B ports with straight types or elbows facing downward.
• Air leakage from the pipe between the valve and cylinder or from
the fittings will prevent the cylinder from stopping for a long period
of time. Check the leakage using neutral household detergent,
Base gasket such as dish washing soap. Also, check the cylinder’s tube
gasket, piston packing and rod packing for air leakage.
• Combining with 3-position closed center or pressure center valve
will not work.
• If the exhaust of the double check spacer is restricted too much,
4(A) 2(B) EXH.
the cylinder may not operate properly and may not stop 5(EA)
intermediately. 1(P)
Connector gasket 3(EB)
• Set the cylinder load so that the cylinder pressure will be within two Circuit diagram
Part numbers of times that of the supply pressure. (Drop prevention: When 2-position single valve is mounted)
mounting screw (For repairs)
SY3000: SY3000-23-27A (2 pcs.)
SY5000: SY5000-221-4A (2 pcs.)
SY7000: SY7000-221-4A (3 pcs.)
227
Manifold Options Series SY3000/5000/7000
Valve
Caution
Tightening torque for mounting screw
M2: 0.12 lbf ft (0.16 N·m) (SY3000)
Manifold Options ∗ Refer to pages 237, 239, 241 for dimensions. M3: 0.59 lbf ft (0.8 N·m) (SY5000/7000)
Interface regulator
[With a connector gasket, a base gasket, and two mounting screws (3 pcs. for the SY7000)]
Sub-plate
Used when the supply pressure for each valve on the same manifold must be individually set (reduced pressure).
How to Order
SY 3 0M 05 P
Plug-in
Series Applicable valve Note 3)
3 SY3000 Nil For single, double, and 4-position
3 For 3-position
Pressure gauge option Note 1)
Note 1) In the case of the SY3000 series with a pressure gauge, when mounting on the manifold,
M1 No pressure gauge use caution that the part numbers are different between the odd no. stations and the even
05 Pressure gauge with MPa display (For odd number station) no. stations to prevent the pressure gauges from interfering with each other.
Metal Base
06 Pressure gauge with MPa display (For even number station) If using a connector connecting base M10/11/12 (mixed mounting type), you can use only
the model without a pressure gauge (M1).
N5 Pressure gauge with psi display (For odd number station) Note 2)
Note 2) As per the new Measurement Law, gauges with a psi display will only be sold to overseas
N6 Pressure gauge with psi display (For even number station) Note 2) customers.
Note 3) In the case of the SY3000 series, use caution that the part numbers will differ depending on
the one for single/double and 4- and 3-position due to the different length of solenoid
SY 5 0M 00 P
Plug-in
valves. Also, if you have selected a model with a pressure gauge, and if at least the one for
3-position is included in the same manifold, use all the ones for 3-position to prevent the
pressure gauges from interfering with each other.
Series
5 SY5000
7 SY7000 Regulating port
Mounting screw
Connector gasket
Plug-in
SY30M-05/N5- SY30M-06/N6- SY30M-M1- SY50M-00/N0- SY50M-M1- SY70M-00/N0- SY70M-M1-
(With pressure gauge/ (With pressure gauge/ (Without pressure gauge) (With pressure gauge) (Without pressure gauge) (With pressure gauge) (Without pressure gauge)
For odd number station) For even number station)
2(B) (A)4
Manifold Options
(EA)5 3(EB)
(EA)5 3(EB) (EA)5 3(EB)
228
Series SY3000/5000/7000 Caution
Tightening torque for mounting screw
M2: 0.12 lbf·ft (0.16 N·m) (SY3000)
Mounting Screw Part No. q (when adding optional lamination layers) M3: 0.59 lbf·ft (0.8 N·m) (SY5000/7000)
<Round head combination screw> SY3000- SY3000- SY5000- SY5000- SY7000- SY7000-
q: SY3000-23-24A A Valve 23-24A 222-1A 221-1A 222-1A 221-1A 222-1A
[for 10 valves [for 10 valves [for 10 valves [for 10 valves [for 10 valves [for 10 valves
w: SY5000-221-1A
(20 pcs.)] (20 pcs.)] (20 pcs.)] (20 pcs.)] (30 pcs.)] (30 pcs.)]
e: SY7000-221-1A
<Hexagon socket head cap screw> SUP stop valve
A q: SY3000-222-1A spacer assembly
w: SY5000-222-1A B with residual
B e: SY7000-221-1A pressure
release valve SY30M-56-2A SY50M-56-2A SY70M-56-2A
q: SY30M-56-2A
(2 pcs.) (2 pcs.) (3 pcs.)
C w: SY50M-56-2A Individual
e: SY70M-56-2A SUP (EXH)
C spacer
assembly
A Valve
<Round head combination screw>
q: SY3000-23-33A
w: SY5000-221-5A Double check
A e: SY7000-221-5A spacer assembly SY3000- SY5000- SY7000-
B with residual 23-33A — 221-5A — 221-5A —
B pressure release (2 pcs.) (2 pcs.) (3 pcs.)
valve
C Individual
SUP (EXH)
C spacer
assembly
A Valve
<Round head combination screw>
q: SY3000-23-32A
w: SY5000-221-3A
A Individual
e: SY7000-221-3A SUP (EXH)
SY3000- SY5000- SY7000-
B B spacer 23-32A — 221-3A — 221-3A —
assembly (2 pcs.) (2 pcs.) (3 pcs.)
C Individual
EXH (SUP)
C spacer
assembly
229
Manifold Options Series SY3000/5000/7000
Caution
Valve
Tightening torque for mounting screw
M2: 0.12 lbf·ft (0.16 N·m) (SY3000)
Mounting Screw Part No. w (when adding optional lamination layers) M3: 0.59 lbf·ft (0.8 N·m) (SY5000/7000)
Sub-plate
Combination
Round head Hexagon socket Round head Hexagon socket Round head Hexagon socket
combination screw head cap screw combination screw head cap screw combination screw head cap screw
<Round head combination screw> SY3000- SY3000- SY5000- SY5000- SY7000- SY7000-
23-24A 222-1A 221-1A 222-1A 221-1A 222-1A
Plug-in
q: SY3000-23-24A A Valve
w: SY5000-221-1A [for 10 valves [for 10 valves [for 10 valves [for 10 valves [for 10 valves [for 10 valves
e: SY7000-221-1A (20 pcs.)] (20 pcs.)] (20 pcs.)] (20 pcs.)] (30 pcs.)] (30 pcs.)]
<Hexagon socket head cap screw> SUP stop valve
q: SY3000-222-1A spacer assembly
A
w: SY5000-222-1A B with residual
e: SY7000-222-1A pressure
B release valve
SY30M-56-3A SY50M-56-3A SY70M-56-3A
Metal Base
q: SY30M-56-3A Double check (2 pcs.) (2 pcs.) (3 pcs.)
C w: SY50M-56-3A spacer
assembly with
e: SY70M-56-3A C residual
pressure
release valve
Plug-in
SY3000- SY3000- SY5000- SY5000- SY7000- SY7000-
23-24A 222-1A 221-1A 222-1A 221-1A 222-1A
<Round head combination screw> A Valve
[for 10 valves [for 10 valves [for 10 valves [for 10 valves [for 10 valves [for 10 valves
q: SY3000-23-24A (20 pcs.)] (20 pcs.)] (20 pcs.)] (20 pcs.)] (30 pcs.)] (30 pcs.)]
w: SY5000-221-1A
Individual
D EXH (SUP)
spacer
assembly
A Valve
Plug-in
<Round head combination screw>
q: SY3000-23-32A
A w: SY5000-221-7A
C
Individual
C SUP (EXH)
spacer
assembly
Plug Assembly Part No.
Note 1) The fitting for individual SUP/EXH spacers comes in a straight type only, since an elbow type would interfere with each spacer assembly when laminated.
Note 2) When laminating an interface regulator with other options, only the combinations in the table above are possible.
Manifold Options
230
Series SY3000/5000/7000
Caution
Tightening torque for mounting screw
M2: 0.12 lbf·ft (0.16 N·m) (SY3000)
Manifold Options ∗ Refer to pages 237, 239, 241 for dimensions. M3: 0.59 lbf·ft (0.8 N·m) (SY5000/7000)
Individual SUP block assembly Mounting screw How to Order Individual SUP/EXH Block Assembly
On the circuit of the plug-in connector
One-touch fitting
connection base, an individual SUP block
assembly can be used to supply air to a Straight type SY 3 0M 78 1 A C6
series of valves if a separate air supply is One-touch fitting
required, or if addition air is required for Elbow type SY 3 0M 78 2 A L6
additional air flow.
Individual SUP block assembly occupies 1 Series
station. 3 SY3000
Blocking disks also supplied (2 pieces). 5 SY5000 Block type
Can be used to block both sides of the 7 SY7000
78 Individual SUP block
number of stations being isolated for SUP blocking disk
assembly 79 Individual EXH block
individual air supply (as shown in
example).
<Example> Individual SUP/EXH block assembly
∗ Specify the mounting position of the
2 Short elbow type (Type 12)
block as well as the position where the D side U side
3 Long elbow type (Type 11)
SUP passage is to be blocked on the 5(EA) 5(EA)
1(P) X X 1(P) Note) Long elbow type is for the
manifold specification sheet. 3(EB) 3(EB) SY5000/7000 only.
Blocking is required for 1 or 2 positions for
1 set. (2 SUP blocking disks to block SUP Port size (Metric/One-touch fittings)
is attached to individual SUP block.) Symbol P, E port SY3000 SY5000 SY7000
∗ Electrical wiring is connected to a
L4 ø4 —
number of stations in the individual SUP L6 ø6
block manifold. 1(P)
L8 ø8 —
(A)4 2(B) (A)4 2(B) (A)4 2(B) (A)4 2(B) (A)4 2(B)
∗ When used in M10/11/12 (mixed L10 ø10 — —
mounting type), select the SY50M type L12 ø12 — —
for SS5Y5 and the SY70M type for
SS5Y7. Port size (Inch/One-touch fittings)
∗ A structure to prevent screws falling out Mounting screw Symbol P, E port SY3000 SY5000 SY7000
is in place on the individual SUP block, LN3 ø5/32" — —
making it much harder for the mounting LN7 ø1/4" —
screws to fall out. LN9 ø5/16" — —
LN11 ø3/8" — —
Individual EXH block assembly
On the circuit of the plug-in connector
Port size (Metric/One-touch fittings)
connection base, individual EXH block
Symbol P, E port SY3000 SY5000 SY7000
assembly can be used to individually
C2 ø2 — —
exhaust series of valves when the exhaust
C3 ø3 — —
from the valves would affect a number of
EXH blocking disk C4 ø4 —
other stations. assembly C6 ø6
Individual EXH block assembly occupies 1
C8 ø8 —
station. <Example>
C10 ø10 — —
Blocking disks also supplied (4 pieces). D side U side
C12 ø12 — —
Can be used to block both sides of the 5(EA) X X 5(EA)
1(P) 1(P)
number of stations being isolated for 3(EB) X X 3(EB) Port size (Inch/One-touch fittings)
individual exhaust. (as shown in example). Symbol P, E port SY3000 SY5000 SY7000
∗ Specify the mounting position of the N1 ø1/8" — —
block as well as the position where the N3 ø5/32" —
EXH passage is to be blocked on the N7 ø1/4"
manifold specification sheet. N9 ø5/16" —
Blocking is required for 1 or 2 positions 3(R) N11 ø3/8" — —
(A)4 2(B) (A)4 2(B) (A)4 2(B) (A)4 2(B) (A)4 2(B)
for 1 set. (2 sets of EXH blocking disks (4
pcs.) to block EXH is attached to
individual EXH block.)
∗ Electrical wiring is connected to a
number of stations in the individual EXH
block manifold.
∗ When used in M10/11/12 (mixed
mounting type), select the SY50M type
for SS5Y5 and the SY70M type for
SS5Y7.
∗ A structure to prevent screws falling out
is in place on the individual EXH block,
making it much harder for the mounting
screws to fall out.
231
Manifold Options Series SY3000/5000/7000
Valve
Manifold Options
SUP/EXH blocking disk assembly (for connector type manifold, Type 10, 11, 12)
Sub-plate
[SUP blocking disk]
By inserting the SUP blocking disk in the pressure supply passage of the
manifold valve, can provide two different high and low pressure in one
manifold.
Plug-in
[EXH blocking disk]
By inserting the EXH blocking disk in the exhaust passage of the manifold SUP blocking EXH blocking
Series
valve, can separate the exhaust from the valve so it does not affect the disk assembly disk assembly
other valves. It can also be used for the manifold for the positive pressure SY3000 SY30M-40-1A SY30M-40-2A
and vacuum mixed manifold. (2 pcs. are required to block FA/EB both SY5000 SY50M-40-1A SY50M-40-1A
sides of the EXH.) SY7000 SY70M-40-1A SY70M-40-1A
Metal Base
Label for blocking disk ∗ If the blocking disk assembly is ordered using
Label to indicate and confirm on the manifold where the SUP/EXH blocking the manifold specification sheet and ordered at
disk assemblies were inserted. (3 sheets each) the same time as the manifold, the position
where the blocking disk assembly is inserted will
Plug-in
SUP/EXH blocking SUP blocking EXH blocking be labeled and shipped out.
disk label disk label disk label
Plug-in
to be installed only in certain manifold stations, clearly indicate the For SY5000/7000
part number and specify the mounting position on the manifold
specification sheet. EA port
2. When the back pressure check valve assembly is mounted, please contact SY5000 SY50M-24-1A
SMC for valve flow-rate characteristics. SY7000 SY70M-24-1A
Ordering Example
SS5Y3-10F1-05B-C6·····1 set (Type 10 5-station manifold base part no.)
∗SY3201-5U1··················5 sets (2-position double part no.)
Manifold Options
232
Series SY3000/5000/7000
Manifold Options
Dual flow fitting (for connector connecting base, Type 10, side ported)
This is a fitting for cylinder ports which enables simultaneous actuation and increase in flow rate of valves for 2 stations.
∗ When ordering assemblies incorporated into a manifold, refer to the Ordering Example below and specify on the manifold specification sheet.
SY 3 0M 120 1A C8
Series A, B port size (One-touch fittings) Clip
3 SY3000 Symbol A, B port SY3000 SY5000
5 SY5000 C8 ø8 —
Metric size
C10 ø10 —
Dual flow fitting
N9 Inch size
ø5/16" —
N11 ø3/8" —
Ordering Example
SS5Y3-10F1-08B-CM
∗SY3100-5U1
∗SY30M-120-1A-C8
∗The asterisk denotes the symbol for assembly.
Note 1) Specifically for side porting for a connector
SY3000 SY5000 connecting base. Cannot be attached to bottom or
(22.8) (24.1)
top ported, or mixed mounting types that are metal
or connector connecting bases.
Note 2) When adding or changing clips, push them into the
very end of the manifold for each station. Also,
13.6
32.1
26.3
Silencer A
C
(One-touch fitting connection type)
This silencer can be mounted to the 3/5 Series Model Effective area A B C
øB
ød
(E: EXH) port of the manifold in one step. For SY3000 (ø8) AN15-C08 20 mm2 45 13 20
For SY5000 (ø10) AN20-C10 30 mm2 57.5 16.5 30.5
Body Sound absorbing material For SY7000 (ø12) AN30-C12 41 mm2 71.5 20 43.5
Note) Shipped together with the product. (Resin) (Resin sintered body)
233
Manifold Options Series SY3000/5000/7000
Valve
Manifold Options A transparent plastic plate to put a label with the name of the function of the solenoid valve.
Sub-plate
SY7000: For SS5Y7-(M)10/11 (Side/Bottom ported)
SS5Y3-10
Name plate bracket assembly and name plate mounting
instructions SS5Y5- 10
11
Plug-in
Insert it into the groove on the name plate bracket onto which a
SUP/EXH (end) block is mounted, as shown in Figure 2. SS5Y7-(M) 10
11
∗ When ordering assemblies incorporated with a manifold, refer to the
Ordering Example below.
Mounting and Option
Mounting option
Symbol Printing DIN rail Direct
Yes No With Without Specified length mounting
Metal Base
AA — — — —
A — — — —
A0 — — — —
A3 — — — For 3 stations —
Plug-in
—
A24 — — — For 24 stations —
BA — — — —
B — — — —
B0 — — — —
B3 — — — For 3 stations —
62.5
3 1 2 3 4 5 n: Number
of stations
1 3 1 2 3 4 5 n: Number
Pitch of stations
Pitch
10.5
P = 16 (SY5000)
Plug-in
P = 19 (SY7000)
Make sure to mount
Make sure to mount
in the right direction. (20°)
in the right direction.
Name plate insertion hole the end of the Name plate bracket assembly
One-touch Fittings/
SUP/EXH
SUP/EXH block
Figure 1 Figure 2
block
Figure 1 Figure 2
Insertion hole
234
Series SY3000/5000/7000
Manifold Options A transparent plastic plate to put a label with the name of the function of the solenoid valve.
Name plate bracket assembly part no. and number of items ordered
Series SS5Y3-10 SS5Y5-10/11
Name plate assembly part no. SY30M-85-1A SY50M-85-1A
Internal pilot
2 pcs.
Manifold SUP/EXH U/D piping
block assembly Internal pilot
2 pcs.
Pilot type
double sided piping
2 pcs. Caution
External pilot
and 1 pc. Note) 1. Be sure to shut off the power and air supplies before
U/D piping
P, E port entry mounting the name plate bracket assembly.
External pilot Furthermore, since air may remain inside the actuator,
Not required Note)
double sided piping
piping and manifold, confirm that the air is completely
Note 1) If the manifold is an external pilot, an insertion slot for name plates is on the port block of exhausted before performing any work.
the SUP/EXH block assembly. Thus, a bracket assembly is no longer required on the 2. When disassembly and assembly are performed, air
port piping side. leakage may result if the tightening of the bracket
Note 2) Name plate bracket assembly is not required for the SY7000. mounting screws is inadequate.
235
Manifold Options Series SY3000/5000/7000
Valve
Dimensions: Manifold Options/Series SY3000
Blanking plate assembly Individual SUP/EXH spacer assembly
Sub-plate
(Top/Bottom ported)
Plug-in
B A B A B A B A B A B A 3/5E
92.6
92.6
92.7
14 A 14 A 4A 4A 4A 4A
89
89
101.2
101.2
111.6
111.6
1P
12 B 12 B 2B 2B 2B 2B
3.6
14
7.2
Metal Base
13.9
One-touch fitting
(SUP port, EXH port)
One-touch fitting Applicable tube O.D.: ø4, ø5/32"
1 P
(SUP port, EXH port) : ø6, ø1/4"
Applicable tube O.D.: ø4, ø5/32"
Plug-in
62.6
63.1
: ø6, ø1/4"
2B 2 B2 B 3/5 E
4 A4 A
4A
C6: 92.3
N7: 96.1
L6 : 61.3
L6 : 60.8
2 B2 B 3/5 E
4 A4 A
B A B A B A B A B A B A B A B A
92.6
92.6
14 A 14 A 14 A 14 A 14 A 14 A 14 A 14 A
89
89
101.2
101.2
Plug-in
12 B 12 B 12 B 12 B 12 B 12 B 12 B 12 B
LOCK LOCK
1 P 1 P
1 P 1 P
77.6
78.1
77.6
78.1
2B 2 B2 B 3/5 E 2B 2 B2 B 3/5 E
39.5
39
4 A4 A 4 A4 A
4A 4A
Manifold Options
236
Series SY3000/5000/7000
B A B A B A B A B A 3/5E
92.6
92.6
14 A 14 A 14 A 14 A 4 A
89
101.2
112.8
112.8
SUP
1P
12 B 12 B 12 B 12 B 2 B
LOCK LOCK
3.6
PUSH PUSH
One-touch fitting
(SUP port, EXH port)
Applicable tube O.D.: ø4, ø5/32"
: ø6, ø1/4"
1 P 1 P
83.6
LN7: 72.3
84.1
L6 : 69.8
2B 2 B2 B 3/5 E 2 B2 B 3/5 E
4 A4 A 4 A4 A
4A
B A B A B A B A B A B A B A B A B A
(100.7)
(100.7)
92.6
14 A 14 A 14 A 14 A 14 A
92.2
14 A 14 A 14 A 14 A
92.2
92.6
89
(111.7)
103.2
103.2
(118.3)
(111.7)
109.8
109.8
(118.3)
SUP
12 B 12 B 12 B 12 B 12 B 12 B 12 B 12 B 12 B
Max. 14
Max. 14
05
SY30M- N5 --
06
SY30M- N6-- One-touch fitting
SY30M-M1-- (SUP port, EXH port)
Applicable tube O.D.: ø2
: ø3.2, ø1/8"
: ø4, ø5/32"
1 P
: ø6, ø1/4"
1 P 1 P
77.6
76.9
78.1
77.4
62.1
62.6
2B B 3/5
2 B2 B 3/5 E
48
2 B2 B2 B2 E
39.9
40.4
4 A4 A
4 A4 A4 A4 A
4A
237
Manifold Options Series SY3000/5000/7000
Valve
Dimensions: Manifold Options/Series SY5000
Blanking plate assembly Individual SUP/EXH spacer assembly
Sub-plate
(Top/Bottom ported)
Plug-in
BA BA BA BA BA BA 3/5
14 A 14 A 4A 4A 4A 4A
106.2
113.4
113.4
116.7
116.6
126.5
126.4
E
81.6
142.5
142.4
1
P
12 B 12 B 2B 2B 2B 2B
12.6
Metal Base
5.5
18.2
18.2
1 P
One-touch fitting One-touch fitting
73.2
68.6
Plug-in
2B
3/5 E
Applicable tube O.D.: ø4 Applicable tube O.D.: ø4,
4A : ø6, ø1/4" : ø6, ø1/4"
4 A4 A
: ø8, ø5/16" : ø8, ø5/16"
(76.8)
(72.2)
1 P
2 B2 B
3/5 E
4 A4 A
Plug-in
BA BA BA BA BA BA BA BA
14 A 14 A 14 A 14 A 14 A 14 A 14 A 14 A
106.2
106.2
113.4
113.4
127.7
127.9
LOCK LOCK
(6.1)
PUSH PUSH
1 P
2 B2 B
2B
3/5 E
1 P
1 P 4A
90.7
86.1
4 A4 A
1 P
Manifold Options
2 B2 B
2B
51.6
3/5 E
4A
4 A4 A
238
Series SY3000/5000/7000
B A B A B A B A
14 A 14 A 14 A 14 A B A 3/5 B A
106.2
4 A 14 A
113.4
113.4
113.4
138.6
138.8
E
126.7
1
12 B 12 B 12 B 12 B SUP SUP
P
2 B 12 B
LOCK LOCK
PUSH PUSH
5.7
One-touch fitting
(SUP port, EXH port) One-touch fitting
Applicable tube O.D.: ø4 (SUP port, EXH port)
: ø6, ø1/4" Applicable tube O.D.: ø4, ø5/32"
101.2
1 P : ø8, ø5/16"
2 B2 B
2B
3/5 E P
4A
4 A4 A 1 1
(88.9)
1 P 1 P
<Type 50, 51> <Type 10, 11> 2 B2 B 2 B2 B
63.7
3/5 E 3/5 E
4 A4 A 4 A4 A
BA BA BA BA BA BA
14 A 14 A 14 A 14 A 14 A 14 A B A
106.2
14 A
113.4
113.4
127.5
127.5
145.5
145.7
142.7
12 B 12 B 12 B 12 B 12 B 12 B SUP
12 B
21.7
Max. 21
Max. 21
00 One-touch fitting
SY50M- N0-
(SUP port, EXH port)
SY50M-M1- Applicable tube O.D.: ø4,
: ø6, ø1/4"
P : ø8, ø5/16"
96.2
1 P
92.4
91.6
87.8
(38.5)
2 B2 B2 B
74.5
79.1
54.6
2B
50
3/5 E
4A
4 A4 A4 A
<Type 50, 51, 52> <Type 10, 11, 12> <Type 11>
239
Manifold Options Series SY3000/5000/7000
Valve
Dimensions: Manifold Options/Series SY7000
Blanking plate assembly Individual SUP/EXH spacer assembly
Sub-plate
(Top/Bottom ported)
Plug-in
B A B A B A B A B A B A
14 A 14 A 4A 4A 4A 4A
116.7
116.7
128.8
128.8
133.2
145.1
145.1
92.1
164.1
164.1
12 B 12 B 2B 2B 2B 2B
19.2
38.2
Metal Base
21.7
7.1
One-touch fitting One-touch fitting
(SUP port, EXH port) (SUP port, EXH port)
Plug-in
1 P
Applicable tube O.D.: ø6, ø3/8" Applicable tube O.D.: ø6, ø3/8"
80.1
78.3
2B 2 B2 B : ø8 : ø8
3/5 E : ø10 : ø10
4A
4 A4 A
: ø12 : ø12
(83.2)
(81.4)
1 P
2 B2 B
3/5 E
4 A4 A
Individual SUP/EXH spacer assembly SUP stop valve spacer assembly with residual
(Side ported) pressure release valve
B A B A B A B A B A B A B A B A
Plug-in
14 A 14 A 14 A 14 A 14 A 14 A 14 A 14 A
116.7
116.7
(126.3)
(For ø12)
128.8
(138.2)
148.7
148.7
12 B 12 B 12 B 12 B 12 B 12 B 12 B 12 B
Applicable tube O.D.: ø6, ø1/4" Applicable tube O.D.: ø6, ø1/4"
: ø8, ø5/16" : ø8, ø5/16"
100.9
: ø12 : ø12 2B 2 B2 B
1 P
3/5 E
4 A4 A
4A
Manifold Options
1 P
100.9
99.6
3/5 E
4 A4 A
4A
B A B A B A B A B A B A
14 A 14 A 14 A 14 A 4A 14 A
116.7
(126.3)
(For ø12)
128.8
128.8
(138.2)
145.1
167.1
167.1
SUP SUP
12 B 12 B 12 B 12 B 2B 12 B
7.1
PUSH LOCK PUSH LOCK
One-touch fitting
(SUP port, EXH port)
One-touch fitting
Applicable tube O.D.: ø6, ø3/8"
: ø8 (SUP port, EXH port)
: ø10 Applicable tube O.D.: ø6, ø3/8"
: ø12 : ø8
: ø10
: ø12
113.6
114.9
P
1 P
2B 2 B2 B
1 1
(95.2)
3/5 E
4 A4 A 1 P 1 P
4A
2 B2 B 2 B2 B
68.8
3/5 E 3/5 E
4 A4 A 4 A4 A
<Type 50, 51> <Type 10, 11>
B A
B A B A B A B A B A B A
14 A
14 A 14 A 14 A 14 A 14 A 14 A
116.7
128.8
143.8
143.8
154.9
164.1
161.8
161.8
SUP
12 B
12 B 12 B 12 B 12 B 12 B 12 B
Max. 21
Max. 21
00
SY70M- N0- P
SY70M-M1-
1 P
(42.4)
3/5 E
One-touch fitting
(SUP port, EXH port)
101.8
103.1
82.8
1 P
81
2B 2 B2 B2 B : ø10
58.3
56.5
3/5 E
: ø12
4 A4 A4 A
4A
Warning Warning
1. Do not use valves in atmospheres of corrosive gases, chemicals, Push-turn locking lever type [Type E]
sea water, water, water vapor, or where there is direct contact with Push down on the manual override by finger until it stops, and
any of these. then turn it 60° clockwise. The manual override is then locked. To
2. Products compliant with IP67 enclosures (based on IEC60529) are release it, turn it counterclockwise. If it is not turned, it can be
protected against dust and water, however, these products cannot operated the same way as the non-locking type.
be used in water. If using in an environment that is exposed to
water and dust splashes, take measures such as using a
Locked
protective cover.
position
3. When using built-in silencer type manifold with an IP67 enclosure,
keep the exhaust port of the silencer from coming in direct contact
with water or other liquids.
4. The metal seal valve is provided with a hole to discharge the pilot OFF
EXH. When using in atmospheres containing water and dust,
mount it horizontally. ON
B
Valve Mounting
(3.7)
SY3000 M2 0.12 lbf ft (0.16 N·m Max. (at OFF): 3.7 mm
gaskets, and tighten with SY5000/7000 M3 0.59 lbf ft (0.8 N·m)
the tightening torque as
shown below.
Manual Override
Warning Caution
Regardless of an electric signal for the valve, the manual override is Do not apply excessive torque when turning the manual override.
used for switching the main valve. Connected actuator is started by [0.1 N·m]
manual operation. Use the manual override after confirming that When locking the manual override, be sure to push it down before
there is no danger. turning. Turning without first pushing it down can cause damage to
Non-locking push type the manual override and other trouble such as air leakage etc.
Push down on the manual
override button until it stops. Slide locking type (Manual)
It is locked by sliding the manual override all the way in the
direction indicated by the arrow (ON side) with a small flat head
screwdriver or with your fingers. Slide it in the direction indicated
by the arrow (OFF side) to release it.
OFF Locked
Push-turn locking slotted type [Type D] position
Push down on the manual override with a small flat head screw- ON
driver until it stops, and then turn it 90° clockwise. The manual
override is then locked. To release it, turn it counterclockwise. OFF
If it is not turned, it can be operated the same way as the
non-locking type. B
ON A
Locked
position
PUSH
TURN
B A
242
Series SY3000/5000/7000
Specific Product Precautions 2
Be sure to read before handling. Refer to back cover for Safety Instructions. For 3/4/5 Port Solenoid Valve Precautions, refer
to “Handling Precautions for SMC Products” and the Operation Manual on SMC website, http://www.smcworld.com
Caution The SY series plug-in valve has the common configuration of the valve
3
mounting surface between base mounted type (SY 57 0) and top
3
There are two types of back pressure check valves; the one which is ported type (SY 57 3), therefore, it can be mounted to all manifolds of
built into a valve (with rubber seal type only) and the one which is the side ported type (Type 50 and Type 10), the bottom ported type
built in on the manifold side with connector connection. Both of them (Type 51 and Type 11) and the top ported type (Type 52 and Type 12).
have a check valve built-in to prevent back pressure. For this reason, For example, air output can be obtained from both sides of the A and B
use caution that the valves with external pilot specification cannot be ports of the manifold and the valve by mounting a top ported valve to a
pressurized from exhaust port [3/5(E)]. As compared with the types side ported or bottom ported manifold, and a pressure switch can be
which do not integrate the back pressure check valve, C value of the connected to the output port on one side. However, when selecting
flow-rate characteristics goes down. Please contact SMC for details. valves and manifolds, note that when a base mounted valve is
The manifold installed type back pressure check valve assembly is mounted to a top ported manifold, there will be no output from the A
assembly parts with a check valve structure. However, since slight air and B port.
leakage against the back pressure is allowed due to its structure,
adverse effects of the back pressure due to increase in exhaust
resistance cannot be prevented if the manifold exhaust port and other
exhaust ports are put together for piping or if the piping diameter is
narrowed. As a result, this may cause the actuator and air operated
equipment to malfunction. So, be careful not to restrict the exhaust
air. If the exhaust resistance becomes large, select a built-in valve
type with rubber seal.
Do not switch valves when A or B port is open to the atmosphere, or
while the actuators and air operated equipment are in operation. For
built-in valve type with rubber seal, the back pressure prevention seal
may be peeled off, which may cause air leakage or malfunctions.
Use caution especially when performing a trial operation or
maintenance work.
Exhaust Throttle
Caution
The SY series pilot valve and main valve share a common exhaust
inside the valve. Therefore, do not block the exhaust port
when arranging the piping.
Caution
In case of using a 5-port valve as a 3-port valve
The SY3000/5000/7000 series can be used as normally closed
(N.C.) or normally open (N.O.) 3-port port valves by closing one of
the cylinder ports 4(A) or 2(B) with a plug. However, they should be
used with the exhaust ports kept open. They are convenient at times
when a double solenoid type 3-port valve is required.
Single
(EA)5 1 3(EB) (EA)5 1 3(EB)
(P) (P)
243
Series SY3000/5000/7000
Specific Product Precautions 3
Be sure to read before handling. Refer to back cover for Safety Instructions. For 3/4/5 Port Solenoid Valve Precautions, refer
to “Handling Precautions for SMC Products” and the Operation Manual on SMC website, http://www.smcworld.com
Caution
Polar type With power saving circuit
Positive common Negative common Power consumption is decreased by approx. 1/3 by reducing the
Single solenoid Single solenoid wattage required to hold the valve in an energized state. (Effective
energizing time is over 67 ms at 24 VDC.)
Light/surge voltage suppressor (Z) Light/surge voltage suppressor (NZ) Note) Be careful of the energizing time, as quick response and high pressure types
Polarity protection diode Polarity protection diode will become operational when the energizing time is over 40 ms.
COM COM
(+) (−) <Standard> <High pressure>
LED Electric circuit diagram
LED
Coil
Coil
(With power saving circuit) Polarity protection diode
[SOL.a] [SOL.a] (Orange) In the case of single solenoid
(−) (+)
(+) (+)
Timer circuit
Surge voltage suppressor (S) Surge voltage suppressor (NS)
Diode
Diode
PWM circuit
Coil
Coil
LED
Polarity protection diode Polarity protection diode
COM COM i2 i1
(+) (−) (−)
(−)
Coil
Coil
Double solenoid, Double solenoid, The above circuit reduces the power consumption for holding in order to
3-position, 4-position 3-position, 4-position save energy. Refer to the electrical power waveform as shown below.
Light/surge voltage suppressor (Z) Light/surge voltage suppressor (NZ) <Electrical power waveform with power saving circuit>
[SOL.b] [SOL.b]
(−) (+) LED Applied voltage
LED
(Green)
Coil
Coil
(Green) 24 V
COM COM
(+) (−)
LED
0V
Coil
Coil
LED (Orange)
[SOL.a] (Orange) [SOL.a]
(−) (+)
Polarity protection diode Polarity protection diode
Coil
COM COM
(+) (−) 0W
67 ms (40 ms)
Coil
Coil
[SOL.a] [SOL.a]
(−) (+) The values in ( ) are for the high pressure and quick response types.
Polarity protection diode Polarity protection diode
• The 12 VDC specification with power saving circuit (standard
Non-polar type specification) does not have the polarity protection diode. Do not make
With surge voltage suppressor (R) a mistake with the polarity.
Single solenoid Double solenoid • Since the voltage will drop by approx. 0.5 V due to the transistor, pay
SOL.b
attention to the allowable voltage fluctuation. (For details, refer to the
(−,+) solenoid specifications of each type of valve.)
COM
Coil
(+,−) Varistor
COM Residual voltage of the surge voltage suppressor
Coil
Varistor
(+,−)
SOL.a Note) If a varistor or diode surge voltage suppressor is used, there is
Coil
(−,+) Varistor
some residual voltage to the protection element and rated voltage.
SOL.a
(−,+) Therefore, refer to the below table and pay attention to the surge
voltage protection on the controller side. Also, since the response
With light/surge voltage suppressor (U) time does change, refer to the valve specifications on page 4.
Single solenoid Double solenoid
Residual Voltage
SOL.b LED
(−,+) Surge voltage DC
COM suppressor
Varistor 24 V 12 V
Coil
(+,−)
COM S, Z Approx. 1 V
Coil
Varistor (+,−)
SOL.a
R, U Approx. 47 V Approx. 32 V
Coil
(−,+) Varistor
LED
SOL.a
(−,+) LED 244
Series SY3000/5000/7000
Specific Product Precautions 4
Be sure to read before handling. Refer to back cover for Safety Instructions. For 3/4/5 Port Solenoid Valve Precautions, refer
to “Handling Precautions for SMC Products” and the Operation Manual on SMC website, http://www.smcworld.com
Surge voltage
24 V
sol.1: Energized
0V
R −60 V
Surge voltage
Internal circuit 24 V
0V
sol.2: De-energized
R −60 V
Surge voltage
24 V
0V
Large capacity
R load: Energized −60 V
Relay
Power supply circuit breaker
24 VDC
Figure 1. Surge intrusion circuit example (NPN outlet example) (24 VDC)
Output circuit
Surge voltage
24 V
0V
sol.1: Energized
−2 V
R
Surge voltage
24 V
Internal circuit
0V
sol.2: De-energized
−2 V
R
Surge voltage
24 V
0V
Large capacity −2 V
R load: Energized
Countermeasure
Diode parts
– (Anode) + (Cathode)
Relay
Power supply circuit breaker
24 VDC
Figure 2. Surge intrusion circuit example (NPN outlet example) (24 VDC)
245
Series SY3000/5000/7000
Specific Product Precautions 5
Be sure to read before handling. Refer to back cover for Safety Instructions. For 3/4/5 Port Solenoid Valve Precautions, refer
to “Handling Precautions for SMC Products” and the Operation Manual on SMC website, http://www.smcworld.com
Caution
E
Connector direction for electrical entry of D-sub connector, flat ribbon FRE
cable and PC wiring can be changed. If the directional change is LOC
K
required, push the lever on both sides to remove the connector and
change the connector direction for electrical entry as shown in the
figure. Since lead wire assemblies are attached to the connector,
excessive pulling or twisting can cause broken wires or other trouble.
Also, take precautions so that lead wires are not caught and pinched
when installing the connector.
How to Order Manifold
Caution
The letter “Í” is indicated on manifold blocks for the SY series Type 1
(connector connecting base) as shown below. This indication refers
to the type of substrate assembly (single wiring) inside the manifold
blocks. When there is no symbol, double wiring is used.
When the manifold specification sheet does not include a wiring
specification, all stations will be double wiring specification. In this
case, single and double solenoid valves can be mounted in any
position, but when a single valve is used, there will be an unused
control signal. To avoid this, indicate positions of manifold blocks for
single wiring specification and double wiring specification on a manifold
specification sheet. (Note that double, 3-or 4-position valves cannot be
used for manifolds blocks with single wiring specification Í.)
Single wiring
marked with Í
246
Series SY3000/5000/7000
Specific Product Precautions 6
Be sure to read before handling. Refer to back cover for Safety Instructions. For 3/4/5 Port Solenoid Valve Precautions, refer
to “Handling Precautions for SMC Products” and the Operation Manual on SMC website, http://www.smcworld.com
Substrate Assemblies inside Manifolds Port Block Assembly and How to Change Piping Types between Top and Side
Caution Caution
Substrate assemblies inside of manifolds cannot be taken apart. For top ported type, the port size of A and B ports can be changed by
Attempting to do so may damage parts. switching the port block assemblies which are mounted on the body.
The piping method can also be changed by switching the top ported
type port block assembly with the side ported type cover assembly.
Also, it may cause air leakage if the mounting screws are not tightened
Fixation of DIN Rail Mounting Type Manifold securely enough when they are switched. Take care to tighten to the
correct tightening torque.
Caution Refer to page 223 for part numbers of port block assembly and body
cover assembly.
1. When the manifold is fixed with bolts on a mounting surface etc., it
When switching them while valves are mounted on a manifold, remove
can be operated just by fixing on both ends of the DIN rail if the
the clip with a flat head screwdriver before switching the port plugs and
bottom surface of the DIN rail is entirely in contact with the mounting
the One-touch fittings. It may cause air leakage if the mounting screws
surface when mounted horizontally. However, if it is used with other
are not tightened or the clip is not inserted securely enough when they
mounting or with side or reverse mounting, fix the DIN rail with bolts
are switched. Take care to tighten to the correct tightening torque.
at regular intervals. As a guide, insert bolts in 2 locations for 2-5
stations, 3 locations for 6-10 stations, 4 locations for 11-15 stations, Caution
5 locations for 16-20 stations and 6 locations for 21-24 stations.
Tightening torque Mounting screw
2. When using the manifold with DIN rail in an environment where any
M2: 0.12 lbf·ft (0.16 N·m) (SY3000)
vibration or impact is applied to it, the DIN rail itself may be broken. M3: 0.59 lbf·ft (0.8 N·m) (SY5000/7000)
In particular, if the installation surface vibrates when mounting the
Port block assembly
manifold on the wall or if a load is directly applied to the manifold, Thread piping
the DIN rail may be broken, causing the manifold to drop. When any
vibration, impact, or load is applied to the manifold, be sure to use
Mounting screw
the direct mounting manifold.
Plate
Plug assembly
For SY3000
Removable by screwing
an M3 screw into the
Plug assembly center hole.
Plate Refer to page 224.
247
Series SY3000/5000/7000
Specific Product Precautions 7
Be sure to read before handling. Refer to back cover for Safety Instructions. For 3/4/5 Port Solenoid Valve Precautions, refer
to “Handling Precautions for SMC Products” and the Operation Manual on SMC website, http://www.smcworld.com
Caution Caution
By replacing One-touch fittings of valve or manifold base, it is possible Bottom ported (Type 11)
to change the connection diameter of the 4(A), 2(B), 1(P), 3/5(E) ports. Secure enough space between
When replacing the One-touch fittings, remove the clip or the plate and the manifold blocks when the
the plate mounting screws with a screwdriver before pulling the plate is detached and attached.
One-touch fittings off. Mount the One-touch fittings by following the Plate part no. (10 pcs. included)
removal procedure in reverse. Plate Series Part no.
It may cause air leakage if the mounting screws are not tightened or SY5000 Note) SY50M-10-4A
the clip and the clip plate are not inserted securely enough when they SY3000/5000 SY50M-10-5A
are switched. Take care to tighten to the correct tightening torque. Mixed mounting type
Refer to page 224 for part numbers of One-touch fittings for valve or SY7000 SY70M-10-4A
manifold. Note) A and B ports (ø8 and ø5/16") of
Valve the SY3000/5000 mixed mount-
Manifold block ing type are those for the
SY5000.
One-touch fitting
Other Tube Brands
Port plate
Caution
Caution 1. When using other than SMC brand tube, confirm that
the following specifications are satisfied with respect to
Tightening torque
the tube outside diameter tolerance.
M2: 0.12 lbf ft (0.16 N·m) 1) Nylon tube within ±0.1 mm
(SY3000) 2) Soft nylon tube within ±0.1 mm
M3: 0.59 lbf ft (0.8 N·m) 3) Polyurethane tube within +0.15 mm
(SY5000/7000) –0.2 mm
Plug-in metal base Do not use tube which do not meet these outside diameter
tolerances. It may not be possible to connect them, or they may
Side ported (Type 50) Bottom ported (Type 51)
cause other trouble, such as air leakage or the tube pulling out after
Clip connection.
One-touch One-touch Fittings
fitting
Tube attachment/detachment for One-touch fittings
Plate 1) Tube attachment
1. Take a tube having no flaws on its periphery and cut it off at a
Plate mounting right angle. When cutting the tube, use tube cutters TK-1, 2 or
screw 3. Do not use pinchers, nippers or scissors, etc. If cutting is
done with tools other than tube cutters, the tube may be cut
Plate assembly part no. diagonally or become flattened, etc., making a secure
Clip part no. (10 pcs. included) (10 pcs. included)
installation impossible, and causing problems such as the tube
Series Part no. Series Part no.
pulling out after installation or air leakage. Allow some extra
SY3000 SY30M-19-2A SY3000 SY30M-10-3A
length in the tube.
SY5000 SY50M-19-2A SY5000 SY50M-10-6A
2. Grasp the tube and push it in slowly, inserting it securely all the
SY7000 SY70M-19-2A SY7000 SY70M-10-7A
way into the fitting.
Note) Including mounting screw 3. After inserting the tube, pull on it lightly to confirm that it will not
Plug-in connector connecting base come out. If it is not installed securely all the way into the
fitting, this can cause problems such as air leakage or the tube
Side ported (Type 10) Clip part no. (10 pcs. included) pulling out.
Port plate SUP/EXH block Series Part no.
2) Tube detachment
Clip SY3000 SY30M-19-1A
One-touch SY5000 Note 1) SY50M-19-6A 1. Push in the release button sufficiently, pushing its collar
fitting SY3000/5000 equally around the circumference.
SY50M-19-1A 2. Pull out the tube while holding down the release button so that
Mixed mounting type
SY7000 SV3000-70-1A it does not come out. If the release button is not pressed down
sufficiently, there will be increased bite on the tube and it will
Note 1) A and B ports (ø8 and ø5/16") of
become more difficult to pull it out.
the SY3000/5000 mixed mounting
3. When the removed tube is to be used again, cut off the portion
type are those for the SY5000.
which has been chewed before reusing it. If the chewed
Note 2) If the port plate for the SUP/EXH
block is required, please contact
portion of the tube is used as is, this can cause trouble such as
SMC.
air leakage or difficulty in removing the tube.
Manifold block
248
Series SY3000/5000/7000
Specific Product Precautions 8
Be sure to read before handling. Refer to back cover for Safety Instructions. For 3/4/5 Port Solenoid Valve Precautions, refer
to “Handling Precautions for SMC Products” and the Operation Manual on SMC website, http://www.smcworld.com
One-touch Fittings
Caution
When fittings are used, they may interfere with one another depending Fittings whose compliance with the SY series is already confirmed are
on their types and sizes. Therefore, the dimensions of the fittings to be stated below. If the fitting within the applicable range is selected, there will
used should first be confirmed in their respective catalogs. not be any interference.
Applicable Fittings: Series KQ2H, KQ2S
Port Applicable tube O.D.
Series Model Piping port Fittings
size ø2 ø3.2 ø4 ø6 ø8 ø10 ø12
KQ2H
SY330--M5 4A, 2B M5
KQ2S
KQ2H
1P, 5EA, 3EB 1/8
KQ2S
KQ2H
SY3000 X, PE M5
SS5Y3-50/51/52 (R) KQ2S
Manifold base KQ2H
1/8
KQ2S
4A, 2B
KQ2H
M5
KQ2S
Trademark
DeviceNet™ is a trademark of ODVA.
EtherNet/IP™ is a trademark of ODVA.
CompoNet™ is a trademark of ODVA.
EtherCAT® is registered trademark and patented technology, licensed by Beckhoff
Automation GmbH, Germany.
249
These safety instructions are intended to prevent hazardous situations and/or
Safety Instructions equipment damage. These instructions indicate the level of potential hazard with
the labels of “Caution,” “Warning” or “Danger.” They are all important notes for
safety and must be followed in addition to International Standards (ISO/IEC)∗1),
and other safety regulations.
∗1) ISO 4414: Pneumatic fluid power – General rules relating to systems.
Caution indicates a hazard with a low level of risk ISO 4413: Hydraulic fluid power – General rules relating to systems.
Caution: which, if not avoided, could result in minor or IEC 60204-1: Safety of machinery – Electrical equipment of machines.
moderate injury.
(Part 1: General requirements)
Warning indicates a hazard with a medium level of ISO 10218-1: Manipulating industrial robots – Safety.
Warning: risk which, if not avoided, could result in death or etc.
serious injury.
Danger indicates a hazard with a high level of risk
Danger : which, if not avoided, will result in death or serious
injury.
Warning Caution
1. The compatibility of the product is the responsibility of the 1. The product is provided for use in manufacturing industries.
person who designs the equipment or decides its specifications. The product herein described is basically provided for peaceful use in
Since the product specified here is used under various operating conditions, its manufacturing industries.
compatibility with specific equipment must be decided by the person who designs If considering using the product in other industries, consult SMC beforehand and
the equipment or decides its specifications based on necessary analysis and test
exchange specifications or a contract if necessary.
results. The expected performance and safety assurance of the equipment will be
If anything is unclear, contact your nearest sales branch.
the responsibility of the person who has determined its compatibility with the
product. This person should also continuously review all specifications of the
product referring to its latest catalog information, with a view to giving due
consideration to any possibility of equipment failure when configuring the Limited warranty and Disclaimer/
equipment.
2. Only personnel with appropriate training should operate
Compliance Requirements
machinery and equipment. The product used is subject to the following “Limited warranty and Disclaimer”
The product specified here may become unsafe if handled incorrectly. The and “Compliance Requirements”.
assembly, operation and maintenance of machines or equipment including our Read and accept them before using the product.
products must be performed by an operator who is appropriately trained and
experienced. Limited warranty and Disclaimer
3. Do not service or attempt to remove product and machinery/
equipment until safety is confirmed. 1. The warranty period of the product is 1 year in service or 1.5 years after
1. The inspection and maintenance of machinery/equipment should only be the product is delivered, whichever is first.∗2)
performed after measures to prevent falling or runaway of the driven objects Also, the product may have specified durability, running distance or
have been confirmed. replacement parts. Please consult your nearest sales branch.
2. When the product is to be removed, confirm that the safety measures as
mentioned above are implemented and the power from any appropriate source 2. For any failure or damage reported within the warranty period which is clearly our
is cut, and read and understand the specific product precautions of all relevant responsibility, a replacement product or necessary parts will be provided.
products carefully. This limited warranty applies only to our product independently, and not to any
3. Before machinery/equipment is restarted, take measures to prevent other damage incurred due to the failure of the product.
unexpected operation and malfunction.
4. Contact SMC beforehand and take special consideration of safety 3. Prior to using SMC products, please read and understand the warranty terms
measures if the product is to be used in any of the following and disclaimers noted in the specified catalog for the particular products.
conditions. ∗2) Vacuum pads are excluded from this 1 year warranty.
1. Conditions and environments outside of the given specifications, or use A vacuum pad is a consumable part, so it is warranted for a year after it is delivered.
Also, even within the warranty period, the wear of a product due to the use of the vacuum pad
outdoors or in a place exposed to direct sunlight.
or failure due to the deterioration of rubber material are not covered by the limited warranty.
2. Installation on equipment in conjunction with atomic energy, railways, air
navigation, space, shipping, vehicles, military, medical treatment, combustion
and recreation, or equipment in contact with food and beverages, emergency Compliance Requirements
stop circuits, clutch and brake circuits in press applications, safety equipment
or other applications unsuitable for the standard specifications described in the 1. The use of SMC products with production equipment for the manufacture of
product catalog. weapons of mass destruction (WMD) or any other weapon is strictly prohibited.
3. An application which could have negative effects on people, property, or
animals requiring special safety analysis. 2. The exports of SMC products or technology from one country to another are
4. Use in an interlock circuit, which requires the provision of double interlock for governed by the relevant security laws and regulations of the countries involved
possible failure by using a mechanical protective function, and periodical in the transaction. Prior to the shipment of a SMC product to another country,
checks to confirm proper operation. assure that all local rules governing that export are known and followed.
Revision history
Edition B ¡Added the EX260 Integrated-type (For Output) Serial ¡Changed the part numbers for A, B port mixed Edition C ¡Added the SY7000.
Transmission System. sizes for plug-in connector connecting bases ¡Added plug-in sub-plate (SY3000/5000).
¡Added EtherNet/IP™ and EtherCAT to the EX600 for Type 10 (Side ported), Type 11 (Bottom ¡Added with residual pressure release valve
Integrated-type (For Input/Output) Serial Transmission ported), Type 12 (Top ported). (SY5000).
System (Fieldbus System).
¡Deleted the mixed specification for A, B port ¡Added with safety slide locking manual override.
¡Additional Options:
· Interface regulator assembly · Dual flow fitting piping specification for plug-in connector ¡Added D-sub connector [IP67] manifold.
· Individual SUP block assembly · Name plate for manifolds connecting base for Type 12 (Top ported). ¡Added PC wiring (with power supply terminal) manifold.
· Individual EXH block assembly ¡Number of pages from 148 to 164 PY ¡Number of pages from 164 to 260 SO
Safety Instructions Be sure to read “Handling Precautions for SMC Products” (M-E03-3) before using.
250
Global Manufacturing, Distribution and Service Network
Worldwide Subsidiaries
EUROPE ASIA NORTH AMERICA
AUSTRIA LATVIA CHINA CANADA
SMC Pneumatik GmbH (Austria) SMC Pneumatics Latvia SIA SMC (China) Co., Ltd. SMC Pneumatics (Canada) Ltd.
BELGIUM LITHUANIA HONG KONG MEXICO
SMC Pneumatics N.V./S.A. SMC Pneumatics Lietuva, UAB SMC Pneumatics (Hong kong) Ltd. SMC Corporation (Mexico) S.A. DE C.V.
BULGARIA NETHERLANDS INDIA USA
SMC Industrial Automation Bulgaria EOOD SMC Pneumatics BV SMC Pneumatics (India) Pvt. Ltd. SMC Corporation of America
CROATIA NORWAY JAPAN
SMC Industrijska Automatika d.o.o. SMC Pneumatics Norway A/S SMC Corporation SOUTH AMERICA
CZECH POLAND MALAYSIA ARGENTINA
SMC Industrial Automation CZ s.r.o. SMC Industrial Automation Polska Sp.z.o.o. SMC Pneumatics (S.E.A.) Sdn. Bhd. SMC Argentina S.A.
DENMARK ROMANIA PHILIPPINES BOLIVIA
SMC Pneumatik A/S SMC Romania S.r.l. SMC Pneumatics (Philippines), Inc. SMC Pneumatics Bolivia S.R.L.
ESTONIA RUSSIA SINGAPORE BRAZIL
SMC Pneumatics Estonia SMC Pneumatik LLC. SMC Pneumatics (S.E.A.) Pte. Ltd. SMC Pneumaticos do Brazil Ltda.
FINLAND SLOVAKIA SOUTH KOREA CHILE
SMC Pneumatics Finland OY SMC Priemyselná Automatizáciá, s.r.o. SMC Pneumatics Korea Co., Ltd. SMC Pneumatics (Chile) S.A.
FRANCE SLOVENIA TAIWAN VENEZUELA
SMC Pneumatique S.A. SMC Industrijska Avtomatika d.o.o. SMC Pneumatics (Taiwan) Co., Ltd. SMC Neumatica Venezuela S.A.
GERMANY SPAIN / PORTUGAL THAILAND OCEANIA
SMC Pneumatik GmbH SMC España, S.A. SMC Thailand Ltd.
AUSTRALIA
GREECE SWEDEN SMC Pneumatics (Australia) Pty. Ltd.
SMC Hellas EPE SMC Pneumatics Sweden AB
NEW ZEALAND
HUNGARY SWITZERLAND SMC Pneumatics (N.Z.) Ltd.
SMC Hungary Ipari Automatizálási Kft. SMC Pneumatik AG
IRELAND UK
SMC Pneumatics (Ireland) Ltd. SMC Pneumatics (U.K.) Ltd.
ITALY
SMC Italia S.p.A.
WEST EAST
Austin Atlanta
Dallas Birmingham
Los Angeles Boston
Phoenix Charlotte
Portland Nashville Vancouver