Professional Documents
Culture Documents
Edition A
175-000412-00
VTM6801+
Three-Channel Serial Monitoring
Distribution Amplifier
Edition A
December 2007
Copyright Information
Copyright 2007 Harris Corporation, 1025 West NASA Boulevard,
Melbourne, Florida 32919-0001 U.S.A.
All rights reserved. This product and related documentation are
protected by copyright and are distributed under licenses restricting
their use, copying, distribution, and decompilation. No part of this
product or related documentation may be reproduced in any form by
any means without prior written authorization of Harris Corporation
and its licensors, if any.
This publication could include technical inaccuracies or typographical
errors. Changes are periodically added to the information herein; these
changes will be incorporated into new editions of the publication.
Harris Corporation may make improvements and/or changes in the
product(s) and/or the program(s) described in this publication at any
time.
All trademarks are property of their respective owners.
Warranty Information
The Limited Warranty Policy provides a complete description of your
warranty coverage, limitations, and exclusions, as well as procedures
for obtaining warranty service. To view the complete warranty, visit our
website.
This publication is provided “as is” without warranty of any kind, either
express or implied, including, but not limited to, the implied warranties
of merchantability, fitness for a particular purpose, or non-infringement.
Contents
Preface
Manual Information .............................................................................. vii
Purpose ........................................................................................... vii
Audience ........................................................................................ vii
Revision History ............................................................................ vii
Writing Conventions ..................................................................... viii
Obtaining Documents ................................................................... viii
Unpacking/Shipping Information .......................................................... ix
Unpacking a Product ....................................................................... ix
Product Servicing ............................................................................ ix
Returning a Product ........................................................................ ix
Restriction on Hazardous Substances (RoHS) Compliance ....................x
Waste from Electrical and Electronic Equipment (WEEE) Compliance xi
Safety .................................................................................................... xii
Safety Terms and Symbols in this Manual .................................... xii
Chapter 1: Introduction
Overview ..................................................................................................1
VTM6801+ Module Product Description ................................................2
Module Descriptions ................................................................................3
Front Module ....................................................................................3
Back Connector .................................................................................5
Signal Flow ..............................................................................................7
Chapter 2: Installation
Overview ..................................................................................................9
Maximum 6800+ Frame Power Ratings ................................................10
Unpacking the Module ...........................................................................11
Preparing the Product for Installation .............................................11
Chapter 3: Operation
Overview ............................................................................................... 15
Understanding Card-Edge Controls ...................................................... 16
Introducing Controls Types ........................................................... 16
Operating Notes ............................................................................. 18
Reading Hardware and Software Version ...................................... 19
LEDs and Alarms .................................................................................. 20
Channel LEDs ................................................................................ 20
Module Status LEDs ...................................................................... 21
Alarms ............................................................................................ 21
Chapter 4: Specifications
Overview ............................................................................................... 23
Input ...................................................................................................... 24
Serial Digital Video Input .............................................................. 24
Output .................................................................................................... 25
Serial Digital Video Output ........................................................... 25
Composite Analog Output ............................................................. 25
Miscellaneous ........................................................................................ 26
Performance ................................................................................... 26
Power Consumption ....................................................................... 26
Start-up Time ................................................................................. 26
Index
Keywords ...............................................................................................35
Manual Information
Purpose
This manual details the features, installation, operation, maintenance,
and specifications for the VTM6801+ Three-Channel Serial
Monitoring Distribution Amplifier.
Audience
This manual is written for engineers, technicians, and operators
responsible for installation, setup, maintenance, and/or operation of the
VTM6801+ Three-Channel Serial Monitoring Distribution Amplifier.
Revision History
Table P-1. Revision History of Manual
Edition Date Comments
A December 2007 Initial release
Writing Conventions
To enhance your understanding, the authors of this manual have
adhered to the following text conventions:
Obtaining Documents
Product support documents can be viewed or downloaded from our
website. Alternatively, contact your Customer Service representative to
request a document.
Unpacking/Shipping Information
Unpacking a Product
This product was carefully inspected, tested, and calibrated before
shipment to ensure years of stable and trouble-free service.
1. Check equipment for any visible damage that may have occurred
during transit.
2. Confirm that you have received all items listed on the packing list.
3. Contact your dealer if any item on the packing list is missing.
4. Contact the carrier if any item is damaged.
5. Remove all packaging material from the product and its associated
components before you install the unit.
Keep at least one set of original packaging, in the event that you need to
return a product for servicing.
Product Servicing
Except for firmware upgrades, VTM6801+ modules are not designed
for field servicing. All hardware upgrades, modifications, or repairs
require you to return the modules to the Customer Service center.
Returning a Product
In the unlikely event that your product fails to operate properly, please
contact Customer Service to obtain a Return Authorization (RA)
number, then send the unit back for servicing.
Keep at least one set of original packaging in the event that a product
needs to be returned for service. If the original package is not available,
you can supply your own packaging as long as it meets the following
criteria:
• The packaging must be able to withstand the product’s weight.
• The product must be held rigid within the packaging.
• There must be at least 2 in. (5 cm) of space between the product and
the container.
• The corners of the product must be protected.
Ship products back to us for servicing prepaid and, if possible, in the
original packaging material. If the product is still within the warranty
period, we will return the product prepaid after servicing.
Safety
Carefully review all safety precautions to avoid injury and prevent
damage to this product or any products connected to it. If this product is
rack-mountable, it should be mounted in an appropriate rack using the
rack-mounting positions and rear support guides provided. It is
recommended that each frame be connected to a separate electrical
circuit for protection against circuit overloading. If this product relies
on forced air cooling, it is recommended that all obstructions to the air
flow be removed prior to mounting the frame in the rack.
If this product has a provision for external earth grounding, it is
recommended that the frame be grounded to earth via the protective
earth ground on the rear panel.
IMPORTANT! Only qualified personnel should perform service
procedures.
CAUTION
Statements identifying conditions or
practices that can result in damage to the
equipment or other property.
Overview
The VTM6801+ is a three-channel serial monitoring distribution
amplifier. It combines the functions of an equalizing, reclocking serial
distribution amplifier, and a 4:2:2 to NTSC/PAL converter of 3
channels on a single distribution-amplifier sized card.
The following topics are described in this chapter:
• “VTM6801+ Module Product Description” on page 2
• “Module Descriptions” on page 3
• “Signal Flow” on page 7
Module Descriptions
Front Module
See Figure 1-1 for an illustration showing a partial top view of the
VTM6801+ module, and the general location of LEDs, switches, and
jumpers.
DIP
switches Gain pots
Remote/local
control
jumper
Back Connector
FR6802+ Frame Back Connector
Figure 1-2 shows the double-slot back connector (VTM6801+DR) used
by the VTM6801+ when installed in an FR6802+ frame.
SDI IN 1
SDI IN 2 CMPST 2
CMPST 3 SDI IN 3
SDI IN 1
SDI IN 2 CMPST 2
CMPST 3 SDI IN 3
Note
Remote control for this 6800+ module is not available if it is
installed in a 6800/7000 series frame.
Signal Flow
Figure 1-4 shows the basic signal flow of the VTM6801+:
SD-SDI out 1
SD-SDI out 2
SD-SDI out 3
Midplane
I/O
CCS remote
monitoring
and control
Overview
This chapter describes the VTM6801+ installation process, including
the following topics:
• “Maximum 6800+ Frame Power Ratings” on page 10
• “Unpacking the Module” on page 11
• “Setting the Jumper” on page 12
• “Installing 6800+ Modules” on page 14
Caution
Note
Contact your Customer Service representative if parts are
missing or damaged.
• Retain the original packaging materials for possible re-use.
See “Unpacking/Shipping Information” on page ix for information
about returning a product for servicing.
Note
You need to configure modules for local or remote operation prior to
power-up. To change the configuration, first remove power from the
module, reset the jumper, and then reapply power.
Follow this procedure to set the J1 jumper for either local or remote
control:
1. Locate jumper J1 on the module (beside the extractor handle).
Figure 2-1 shows the standard location of the J1 jumper.
Local/remote
jumper
2. Place a jumper on pins 1 and 2 to set the module for Local control
or pins 2 and 3 to set the module for Remote control. See
Figure 2-2.
3 2 1 3 2 1
Note
The white triangle near the jumper pins on the module indicates
pin 1.
See Table 1-1 on page 4 for more information on local/remote control
jumper functionality.
Caution
Overview
This chapter describes how to operate the VTM6801+ using card-edge
controls only. See the following documents for information on how to
operate this product remotely:
• + Pilot Lite User Manual for serial control interface
• CCS™ Navigator™, Pilot™ CoPilot™ or RCP-CCS-1U Remote
Control Panel Manual for Ethernet control interface
The following topics are discussed in this chapter:
• “Understanding Card-Edge Controls” on page 16
• “LEDs and Alarms” on page 20
Note
For best results, use the available 6800+ software control options
(serial/local or Ethernet/remote) to aid in viewing, setting, and
confirming parameter values. See Appendix A for more information.
You can control the composite output by adjusting the DIP switch
settings. Each DIP switch has a corresponding LED so that you can
easily monitor the DIP switch settings from the card edge.
The VTM6801+ also has three potentiometer (pot) controls that you
can use to adjust the gain for each channel.
J1 jumper
Operating Notes
You can affect the composite output of each of the three channels by
adjusting the DIP switches for each channel. Each of the three banks of
DIP switches has the following five controls:
See Table 3-2 for specific instructions for setting the DIP switches and
monitoring the LEDs.
Alarms
The VTM6801+ module does not have any card-edge alarms. Instead,
alarms are usually logged and monitored within the available 6800+
software control applications (for example, + Pilot Lite or Pilot). See
the appropriate software control user manual or online help for more
information.
Overview
The following specification tables appear in this chapter:
• “Serial Digital Video Input” on page 24
• “Serial Digital Video Output” on page 25
• “Composite Analog Output” on page 25
• “Performance” on page 26
• “Power Consumption” on page 26
• “Start-up Time” on page 26
Specifications and designs are subject to change without notice.
Input
Serial Digital Video Input
Table 4-1. Serial Digital Video Input Specifications
Item Specification
Format compatibility 4:2:2 serial component
Connector BNC per IEC169-8
Impedance 75Ω
Return loss >18 dB from 5 MHz to 270 MHz
Signal level 800 mV ±10%
Max. input cable Typical 300 m
CMRR 30 V peak-to-peak, up to 60 Hz
Output
Serial Digital Video Output
Table 4-2. Serial Digital Video Output Specifications
Item Specification
Quantity 1 BNC per channel
Connector BNC per IEC169-8
Overshoot <10% (all outputs terminated)
Impedance 75Ω
Return loss >18 dB to clock frequency
Signal level 800 mV ±10%
Jitter <0.2 UI
Rise and fall times 0.40 – 1.5 ns (as per SMPTE-259)
Miscellaneous
Performance
Table 4-4. Performance Specifications
Item Specification
Processing delay 1.6µs
Test signal Color bar: NTSC 100/7.5/75/7.5,
PAL 100/0/75/0
Power Consumption
The power consumption for the VTM6801+ module is typically less
than 10 W.
Start-up Time
The start-up time for the VTM6801+ module is typically less than 1
second.
Overview
Find the following troubleshooting information in this appendix:
• “General Troubleshooting Steps” on page 28
• “Software Communication and Control Issues” on page 30
• “Hardware Communication and Control Issues” on page 34
• “Contacting Customer Service” on page 34
Note
Associated documentation for 6800+ series products can
generally be found in the product-specific manual that
accompanies every module, in the FR6802+ Frame Installation
and Operation Manual, and in the 6800+ Safety Instructions
and Standards Manual.
Product documentation (including manuals, online help, application
notes, erratas, product release notes, and more) can be found on our
website, along with technical support information, training
information, product downloads, and a product knowledge base.
3. Contact your Customer Service representative if, after following
these initial steps, you cannot resolve the issue.
To contact Customer Service, see “Contacting Customer Service”
on page 34.
20-pin
connector
This connector should not have any bent or pressed pins. Even
a slightly depressed or bent pin may cause genlock issues.
d. If there are bent pins, carefully reposition them to their correct
positions.
If this is not possible, you can exchange the back module for a
new one (order part number VTM6801+DR).
Keywords
A-B D
Alarms 21 DIP switches 16
alarm query failed 33 location on board 17
Application not responding 32 settings 18
Back connector Dip switches 3, 4
6800/7000 frame 6 Discovering a module 29
FR6802+ frame 5 Discovery failure 31
installing 14
Black and white output DIP switch 18 E-H
Extractor handle 3, 4
C Features 2
Card-edge controls 16 FR6802+ frames 14
CCS applications 32 Front module 3, 14
changing parameter settings 29 Gain pots 3, 4, 17
refreshing and discovering modules 29
Channel LEDs 3, 4, 17 I
Chrominance 18
Color bar test signal DIP switch 18 Installation 14
Communication failure, frame 34 preparing for 11
Connections Installed modules 31
external 5, 6 Internal connections 14
internal 14
Control parameters J-K
changing using CCS applications 29
Jumper J1
Control problems 32
position 17
Controls, card-edge 16
setting 12
CoPilot 32
Harris is a registered trademark of Harris Corporation. Trademarks and tradenames are the property of their respective companies.