Professional Documents
Culture Documents
The AZ34063D is a monolithic switching regulator • Operation from 3.0V to 36V Input
control circuit which contains the primary functions • Low Standby Current
required for DC-DC converters. This device consists • Current Limiting
of internal temperature compensated reference, voltage
• Output Switch Current to1A
comparator, controlled duty cycle oscillator with active
• Output Voltage Adjustable
current limit circuit, driver and high current output
switch. • Operation Frequency up to 180kHz (CT=100pF)
• Precision 2% Reference
The AZ34063D is specifically designed as a general
DC-DC converter to be used in Step-Down, Step-Up Applications
and Voltage-Inverting applications with a minimum
number of external components.
· Battery Chargers
· ADSL Modems
The AZ34063D is available in 2 packages: SOIC-8 and · Hubs
DIP-8. · Negative Voltage Power Supplies
SOIC-8 DIP-8
1
Data Sheet
M Package P Package
(SOIC-8) (DIP-8)
Switch 1 8 Driver
Switch 1 8 Driver Collector Collector
Collector Collector
Switch IPK Sense
Switch IPK Sense 2 7
2 7 Emitter
Emitter
Timing Timing VCC
3 6 VCC 3 6
Capacitor Capacitor
Comparator Comparator
GND 4 5 GND 4 5
Inverting Input Inverting Input
Driver 8 1 Switch
Collector B
Collector
S Q
A
R
7 2 Switch
IPK Sense Emitter
Ipk
IPK
CT
OSC
VCC
6 3 Timing
Capacitor
1.25V
+ Reference
Regulator
-
Comparator 5 4
Inverting GND
Input
2
Data Sheet
Ordering Information
AZ34063D -
BCD Semiconductor's Pb-free products, as designated with "G1" suffix in the part number, are RoHS compliant and green.
3
Data Sheet
Note 1: Stresses greater than those listed under "Absolute Maximum Ratings" may cause permanent damage to the device.
These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated
under "Recommended Operating Conditions" is not implied. Exposure to "Absolute Maximum Ratings" for extended periods
may affect device reliability.
Note 2: Maximum package power dissipation limits must be observed.
4
Data Sheet
Note 3: Low duty cycle pulse technique are used during test to maintain junction temperature as close to ambient temperature
as possible.
Note 4: If the output switch is driven into hard saturation (non-Darlington configuration) at low switch currents (≤300mA) and
high driver currents (≥30mA), it may take up to 2.0µs for it to come out of saturation. This condition will shorten the off time
at frequencies 30KHz, and is magnified at high temperatures. This condition does not occur with a Darlington configuration,
since the output switch cannot saturate. If a non-Darlington configuration is used, the following output drive condition is rec-
ommended:
5
Data Sheet
1000
Ton-off Output Switch On-Off Time (µs)
VCC=5.0V
VPIN7=VCC
Vosc Oscillator Voltage (V)
VPIN5=GND
O
100 TA=25 C ton
200mV/DIV
toff
10
0.1 1 10 100
CT Oscillator Timing Capacitor (nF)
Time 20µs/DIV
Figure 4. Output Switch On-Off Time vs. Figure 5. Timing Capacitor Waveform
Oscillator Timing Capacitor
3.5
VCC=5.0V
100 VPIN7=VCC 3.0
VPIN5=GND
ICC Supply Current (mA)
Oscillator Frequency (kHz)
O
TA=25 C 2.5
10 2.0
CT=1.0nF
1.5
VPIN7=VCC
1 VPIN2=GND
1.0
0.5
0.1 1 10 100 0 5 10 15 20 25 30 35 40
Figure 6. Oscillator Frequency vs.Timing Capacitor Figure 7. Standby Supply Current vs. Supply Voltage
6
Data Sheet
1.70 1.2
1.1
1.65 1.0 Darlington Connection
0.9
0.8
0.7
1.55
0.6
0.5
1.50 Forced β=20
0.4
VCC=5.0V VCC=5.0V
0.3
1.45 VPIN1,7,8=VCC VPIN7=VCC
0.2
VPIN3,5=GND VPIN2,3,5=GND
1.40 0.1
O O
TA=25 C 0.0
TA=25 C
1.35 -0.1
0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 1.1 1.2 1.3 0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 1.1 1.2 1.3
Collector Current (A)
Emitter Current (A)
Figure 8. Emitter Follower Configuration Output Figure 9. Common Emitter Configuration Output Switch
Saturation Voltage vs. Emitter Current Saturation Voltage vs. Collector Current
300 1.27
295
Current Limit Sense Voltage (mV)
290 1.26
Feedback Voltage (V)
285
280 1.25
275
270 1.24
265
260 1.23
255
250 1.22
-60 -40 -20 0 20 40 60 80 100 120 140 -40 0 40 80 120 160
O O
Temperature ( C) Temperature ( C)
Figure 10. Current Limit Sense Voltage vs. Temperature Figure 11. Feedback Voltage vs. Temperature
7
Data Sheet
130 1.4
120
Operation Frequency (kHz)
110
90
80
1.0
70
VCC=5.0V ISW =1.0A
CT=330pF VCC=5.0V
60
PIN1 PIN8 Connected
50 0.8
-40 0 40 80 120 160 -40 0 40 80 120 160
O o
Temperature ( C) Temperature ( C)
Figure 12. Operation Frequency vs. Temperature Figure 13. Saturation Voltage vs. Temperature
8
Data Sheet
L1 220µH
R3 180
8 1
B
S Q
A
R
7 2
Ipk
IPK
Rsc D1
0.4 CT 1N5819
OSC
VIN 12V 6 3
+ CT
C1 470pF
1.25V
100µF + Reference
Regulator
-
5 4
L2 1.0µH
U1 AZ34063D
VOUT VOUT
28V/175mA
R1 47k + +
R2 C2 C3
330 µF Optional 100 µF
2.2k
Filter
Note 5: This is a typical step-up converter configuration. In the steady state, if the resistor divider voltage at pin
5 is greater than the voltage in the non-inverting input, which is 1.25V determined by the internal reference, the
output of the comparator will go low. At the next swithching period, the output switch will not conduct and the
output voltage will eventually drop below its nominal voltage until the divider voltage at pin 5 is lower than 1.25V.
Then the output of the comparator will go high, the output switch will be allowed to conduct. Since VPIN5=VOUT *
R2/(R1+R2)=1.25(V), the output voltage can be decided by VOUT=1.25 * (R1+R2)/R2 (V).
9
Data Sheet
8 1
B
S Q
A
R
7 2
Ipk
IPK
Rsc D1
0.33 CT 1N5819
OSC
L1
220 µH
VIN 25V 6 3
+
C1 CT
1.25V
100µF + 470 pF
Reference
Regulator
-
5 4
U1 AZ34063D L2 1.0 µH
VOUT VOUT
5V/500mA
R1 3.6k + +
C2 C3
R2 Optional
470 µF 100 µF
1.2k Filter
Note 6: This is a typical step-down converter configuration. The working process in the steady state is similar to
step-up converter, VPIN5=VOUT*R2/(R1+R2)=1.25 (V), the output voltage can be decided by VOUT=1.25*
(R1+R2)/R2 (V).
10
Data Sheet
8 1
B
S Q
A
R
7 2
Ipk
IPK L1
Rsc 88 µΗ
0.24 CT
OSC
VIN 6 3
4.5-6V
+
C1 1.25V CT
100 µF + Reference 470pF D1
Regulator 1N5819
-
5 4
U1 AZ34063D
L2 1.0 µH
VOUT
VOUT
-12V/100mA
R1 953 C3
C2 100 µF
R2 + Optional
+
1000 µF
8.2k Filter
Note 7: This is a typical inverting converter configuration. The working process in the steady state is similar to
step-up converter, the difference in this situation is that the voltage at the non-inverting pin of the comparator is
equal to 1.25V+VOUT, then VPIN5=VOUT*R2/(R1+R2)=1.25V+VOUT, so the output voltage can be decided by
VOUT=-1.25*(R1+R2)/R1 (V).
11
Data Sheet
4.700(0.185) 0.320(0.013)
5.100(0.201) 1.350(0.053)
7° 1.750(0.069)
8°
7° 8°
0.675(0.027)
D
0.725(0.029) 5.800(0.228)
1.270(0.050) 6.200(0.244)
TYP
D
20:1
0.100(0.004) 0.800(0.031)
R0.150(0.006)
0.300(0.012)
0.200(0.008)
0°
8°
1.000(0.039)
3.800(0.150)
4.000(0.157)
0.190(0.007) 1°
0.330(0.013) 0.250(0.010) 5°
0.510(0.020)
0.900(0.035) R0.150(0.006)
0.450(0.017)
0.800(0.031)
12
Data Sheet
0.700(0.028)
7.620(0.300)TYP
1.524(0.060) TYP
5°
6° 6°
3.200(0.126)
3.710(0.146) 3.600(0.142)
4.310(0.170) 4°
4°
0.510(0.020)MIN
3.000(0.118)
3.600(0.142)
0.204(0.008)
0.254(0.010)TYP 0.360(0.014)
0.360(0.014) 2.540(0.100) TYP 8.200(0.323)
0.560(0.022) 9.400(0.370)
0.130(0.005)MIN
6.200(0.244)
R0.750(0.030) 6.600(0.260)
Φ3.000(0.118)
Depth
0.100(0.004)
0.200(0.008)
9.000(0.354)
9.400(0.370)
13
BCD Semiconductor Manufacturing Limited
http://www.bcdsemi.com
IMPORTANT NOTICE
IMPORTANT NOTICE
BCD Semiconductor
BCD Semiconductor Manufacturing
Manufacturing Limited
Limited reserves
reserves the
the right
right to
to make
make changes
changes without
without further
further notice
notice to
to any
any products
products oror specifi-
specifi-
cations herein.
cations herein. BCD
BCD Semiconductor
Semiconductor Manufacturing
Manufacturing Limited
Limited does
does not
not assume
assume any
any responsibility
responsibility for
for use
use of
of any
any its
its products
products for
for any
any
particular purpose,
particular purpose, nor
nor does
does BCD
BCD Semiconductor
Semiconductor Manufacturing
Manufacturing Limited
Limited assume
assume any
any liability
liability arising
arising out
out of
of the
the application
application or
or use
use
of any
of any its
its products
products or
or circuits.
circuits. BCD
BCD Semiconductor
Semiconductor Manufacturing
Manufacturing Limited
Limited does
does not
not convey
convey anyany license
license under
under its
its patent
patent rights
rights or
or
other rights
other rights nor
nor the
the rights
rights of
of others.
others.
MAIN SITE
MAIN SITE
- Headquarters
BCD Semiconductor Manufacturing Limited - Wafer
BCD FabSemiconductor Manufacturing Limited
BCD Semiconductor
- Wafer Fab Manufacturing Limited Shanghai SIM-BCD
- IC Design GroupSemiconductor Manufacturing Co., Ltd.
No. 1600, Zi
Shanghai Xing Road,
SIM-BCD Shanghai ZiZhu
Semiconductor Science-basedLimited
Manufacturing Industrial Park, 200241, China 800 Yi Shan Road,
Advanced Shanghai
Analog 200233,
Circuits China Corporation
(Shanghai)
Tel:
800,+86-21-24162266, Fax: +86-21-24162277
Yi Shan Road, Shanghai 200233, China Tel: +86-21-6485 1491,YiFax:
8F, Zone B, 900, Shan+86-21-5450 0008200233, China
Road, Shanghai
Tel: +86-21-6485 1491, Fax: +86-21-5450 0008 Tel: +86-21-6495 9539, Fax: +86-21-6485 9673
REGIONAL SALES OFFICE
Shenzhen OfficeSALES OFFICE
REGIONAL Taiwan Office USA Office
Shanghai
Shenzhen SIM-BCD
Office Semiconductor Manufacturing Co., Ltd., Shenzhen Office BCD Taiwan
Semiconductor
Office (Taiwan) Company Limited BCD Office
USA Semiconductor Corp.
Unit A Room
Shanghai 1203, Skyworth
SIM-BCD Bldg., Gaoxin
Semiconductor Ave.1.S., Nanshan
Manufacturing Co., Ltd.District,
Shenzhen Shenzhen,
Office 4F, 298-1,
BCDRui Guang Road,(Taiwan)
Semiconductor Nei-Hu District,
Company Taipei,
Limited 30920Semiconductor
BCD Huntwood Ave.Corporation
Hayward,
China
Advanced Analog Circuits (Shanghai) Corporation Shenzhen Office Taiwan4F, 298-1, Rui Guang Road, Nei-Hu District, Taipei, CA 94544,
30920 USA Ave. Hayward,
Huntwood
Tel:
Room +86-755-8826
E, 5F, Noble 7951 Tel: +886-2-2656
Center, No.1006, 3rd Fuzhong Road, Futian District, Shenzhen 518026, China Taiwan 2808 Tel :94544,
CA +1-510-324-2988
U.S.A
Fax: +86-755-88267951
Tel: +86-755-8826 7865 Fax: +886-2-2656 28062808
Tel: +886-2-2656 Fax:: +1-510-324-2988
Tel +1-510-324-2788
Fax: +86-755-8826 7865 Fax: +886-2-2656 2806 Fax: +1-510-324-2788