Professional Documents
Culture Documents
MAIN PRODUCTS Durability 300 m/s2 (approx. 30G) in each X Y Z direction for 3times NPN Open Collector + Current Output [RP3-5A(D)4]
Shock
-tance
Resis
Multi Pulse Meter - DIGITAL : Temperature Controller, Counter, Timer,Speedmeter,
Malfunction
RP3
Tachometer, Panel Meter, Recorder 100 m/s2 (approx. 10G) in each X Y Z direction for 3times
- SENSOR : Proximity Sensor/Photo Electric Sensor, Operating Ambient
Rotary Encoder, Optical Fiber Sensor, -10 ~ +60 (without condensation)
Temperature
Pressure Sensor
Storage Temperature
INSTRUCTION MANUAL - ANALOG : Timer, Temperature Controller -20 ~ +60 (without condensation)
Operating Ambient
We appreciate you for purchasing HanYoung NUX Co.,Ltd 35 ~ 85 % RH
product. Before using the product you have purchased, HEAD OFFICE Humidity
check to make sure that it is exactly what you ordered. Then, 1381-3, Juan-Dong, Nam-Gu Incheon, Korea
please use it following the instructions below.
Weight Approx. 220 g NPN Open Collector + RS-485 Communication [RP3-5A(D)5]
TEL: (82-32)876-4697 FAX : (82-32)876-4696
Main Circuit
contents. (Use at Pollution level 1 or 2) Display Method 7 Segment (Font size(W)83 mm x (H)14 mm)
7. Do not polish this product with substances such as alcohol or benzene. (Use neutral
detergent.) Display Cycle 0.05/0.5/1/2/4/8 sec Indicator [RP3 - 5A(D)N]
8. Do not use this product at any place with a large inductive difficulty or occurring static Hysteresis 0 ~ 9999 (applicable only for output type)
electricity or magnetic noise.
9. Do not use this product at any place with possible thermal accumulation due to direct Auto Zero Time Setting Function
sunlight or heat radiation. Display Cycle Setting Function : PNP Normal Open
10. Install this product at place under 2,000m in altitude.
11. When the product gets wet, the inspection is essential because there is danger of an Time Unit Selection Function : PNP Normal Close
electric leakage or fire. Parameter Lock Function
12. If there is excessive noise from the power supply, using insulating transformer and noise
filter is recommended. Remote/Local Conversion Function Example : Wiring with
Main Circuit
13. The noise filter must be attached to a panel which is already connected to a ground and the (applicable only for communication output type) Proximate Sensor
Functions
wire between the filter output side and power supply terminal must be short as possible.
14. If twisting the power cables closely together then it is effective against noise. Current Output Range Selection Function
15. Do not connect anything to the unused terminals.
16. After checking the polarity of terminal, connect wires at the correct position.
(applicable only for current output type) Contact output [RP3 - 5A(D)1] Contact output [RP3 - 5A(D)2]
17. When this product is connected onto a panel, use a circuit breaker or switch approved with Max. Min. Peak Value 10 Steps Memory Function
IEC947-1 or IEC947-3. Start Compensation Timer Function : Contact Input Normal Open
18. Install a circuit breaker or switch at near place for convenient use.
19. Write down on a label that if the circuit breaker or switch is operating then the power will be Electricity Failure Compensation (applicable only for F9)
disconnected since the circuit breaker or switch is installed. Comparative Output Function (HH, H, GO, L, LL)
Main Circuit
20. For the continuous and safe use of this product, the periodical maintenance is
recommended. Transistor Output (NPN/PNP Open Collector Output):
21. Some parts of this product have limited life span, and others are changed by their usage.
22. The warranty period for this product including parts is one year if this product is properly used. Comparative Alarm Output (a Contact)
Output Types
Output
Model Name Suffix code Description Before connecting the sensor, if the input specification is not selected
RS485 Communication Output : 32 channels : Displayed
RP3 Multi Pulse Meter properly, the desired measure value can not be obtained.
Value Output, PC Setting Function)
DIN Size: 96 x 48 x 105.6 Example of sensor type setting
BCD Dynamic Displayed Value Output Function
5 digits 1 stage - Normal open (NPN NO)
Low Speed serial Output
100 - 240V a.c (50 - 60 ) - Normal close (NPN NC)
Above 10 (at 500 V DC mega) Between electrically
24 - 60 V a.c / d.c Insulation Resistance
chargeable part and non-electrically chargeable part
Main output Subsidiary output
By noise simulator, square-shaped wave noise
Output Specification
Only Display - Noise Immunity
Relay 3 stages Output -
(pulse width 1 ) 2000 V NPN Open Collector + BCD Output [RP3-5A(D)3] Contact Output
2000 V AC 50 Hz for 1 minute Max. contact capacity : 1250 V A (a.c), 150 W (d.c)
Relay 5 stages Output -
(between AC power terminal and case, Contact capacity : 5A 250 V a.c, 5 A 30 V d.c
NPN Open Collector 5 Stages Output BCD Output Dielectric Strength
- between AC terminal and measurement input terminal)
NPN Open Collector 4 - 20 Current Life : Electrical life - Around Fifty thousand (3A 250 V a.c)
10 - 55 Hz double amplitude width 0.75 mm Mechanical life - Around Ten million (Twenty times opens and closes
5 Stages Output Output
Resistance
Vibration
cm
Velocity (m/min): IN A Input Cycle(f) x ( =60 x L/N) display value
GO
L
LL
operation. cm 100
Dot Point(Dot) Dot value of each Digit Data L = D (circumference of the revolving object) IN A IN B
Dot Data(D0, D1, D2, D3, D4) D0 : Lowest Digit, m 1
= prescale value, N = the number of waveform per 1 revolution Passing Time
D4 : Highest Digit Quantity(EA) 1 Rotary
HH
Encoder
Output : NPN Open collector Example of Application
H
GO
L sec
Revolution LL
1 2 3 4 1 2 1 2 3 4
Process
Example IN A
IN A
Display value & Units Operation IN A
In case of display value 123.45 Length
HH
H
GO
L
m/min
Display Units IN B
Example of Obtaining a
LL
Interval
Output signal : CLK, Data, Latch m 1 IN A IN B
Rotary
Encoder
CLK cycle : 50 Hz Quantity(EA) 1
Number of output CLK bit Mode : Moving Velocity (m/s) Mode : Time Lag
Number of output Data bit Display the moving velocity from ON of IN A to ON of IN B. Display the time from ON of IN A to ON of IN B after measuring it
Time Lag (T): t(IN A ~ IN B) Display 5×α 2×α
Rated load valtage : 12-24 V d.c Velocity(m/s): IN A Input Frequency(f) x value display. = L (m)
Display value & Units 1 2 3 4 5 1 2 1 2
Example of Application
C1 C2 C3 C23 C24 C25 C1 C2 C3 C4 Display value & Units Example of Application IN A
~ Units Prescale Value( )
Display Units
IN B
mm/s 1000 L IN B IN A value 10 60
20ms 1m IN B IN A ta
9.9999s 59.999s
HH
cm/s 100 L
H
GO
L
LL
m/min A HH
H
HOLD
~ 1m
GO
sec
ta(Pause Time) : ta≥20 mS
L
99.999s 59m59s.9
5us m/s 1 L (default)
999.99s 999m59s B
m/min 60 L Velocity
Latch
~
9999.9s 9h59m59s
1ms
km/hour 3.6 L
99999s 999h59m
Data Output order of serial Transmission
Default of Prescale Value Display t1 t2 Keep t4 t6
START
Mode : Addition Counter (Coefficient)
CLK : Time=1sec, Length=1m. L the Distance from IN A sensor to IN B (unit:m)
order
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25
IN A It starts counting the pulse which inputs to IN A but it does not count the
Shift Display (1/t1)×α (1/t2)×α Keep (1/t4)×α (1/t6)×α t1 ta t2 ta t3 ta t4 ta t5 ta t6 pulse when IN B is ON.
If the RESET input is ON, then the counted value becomes 0.
Data order
Segment
MSB(5)
MSB(4)
MSB(3)
MSB(2)
MSB(1)
LSB(5)
LSB(4)
LSB(3)
LSB(2)
LSB(1)
DP(5)
DP(4)
DP(3)
DP(2)
DP(1)
IN A IN B
Counter = P x (P=Pulse of IN A, =Prescale Value)
Data Dot Point Data Dot Point Data Dot Point Data Dot Point Data Dot Point t1 ta t2 ta t3 ta t4 ta t5 ta t6 HOLD
(5digit ) (5 digit ) (4 digit ) (4 digit ) (3 digit ) (3 digit ) (2 digit ) (2 digit ) (1 digit ) (1 digit ) Example of Application
4 ta(Pause Time) : ta≥20 mS
10 Digit 0
10 Digit IN B If you input 0.1 to the prescale
HOLD value ( ) of IN A and apply the
PV Transmission Output(4-20 mA d.c) ta(Pause Time) : ta≥20 mS
HH
H
GO
L
dot position as then the
LL
Output L
Hys Output LL : Comparative LL
Output LL
Displayed Value
HH Deviation Output
Comparative LL Setting
H Deviation Output
PV
SV : Setting Value Note 6) the display only product, BP6-5AN and the non-main output product, BP6-5A6, are not displayed like the above parameter comparative setting
L Deviation Output
PV : Displayed Value group. If each parameter is set and the hysteresis value is inputted, you can stably obtain the desired output.
LL Deviation Output
2. PS Group (Prescale or Time Option Setting Group) Option setting group)
Setting Menu Meaning Description Initial Setting Menu Meaning Description Initial
Option setting group Set the option of the input/output setting item
Prescale Setting Comparative s prescale value selection selection in the option setting group
Group Selection
IN A s prescale PV transmission output s
mantissa (X) setting high limit value setting
F1, F2, F7, F8, F9 : 0 ~ 99999
IN A s prescale F3, F4, F5, F6 : 0 ~ Set time Lange
exponent (Y) setting PV transmission output s
low limit value setting
For each bank, the When setting the option setting groupz the menu is displayed and it
displayed value s is possible to set the decimal setting individually for each bank
Communication
decimal point setting id setting
For each bank, the When setting the option setting group, the menu is displayed and it
Communication
displayed value s cycle is possible to set the display sampling cycle individually for each speed setting
bank. Setting Unit : bps
setting
: Remote Control
When setting the option setting group, the menu is displayed and it : Local Operation
For each bank, the output s is possible to set the hysteresis value individually for each bank. Remote control setting
3. Setup Group (IN/OUT setting group) 5. Peak Display Group (Peak Value save Group)
Setting Menu Meaning Description Initial Setting Menu Meaning Description Initial
Input/Output control Save the MAX, MIN peak value
Input/Output setting in the Input/Output control setting group Peak value save group
setting group selection of the measured values to the 10 memories
Input Operation 1st value of HIGH peak Save the highest number of the measured value
Mode Setting
: NPN Normal Open : NPN Normal Close 2nd value of HIGH peak Save the second highest number of the measured value
IN A sensor : PNP Normal Open : PNP Normal Close
type setting 3rd value of HIGH peak Save the third highest number of the measured value
: Contact Normal Open
4th value of HIGH peak Save the fourth highest number of the measured value
IN B sensor : NPN Normal Open : NPN Normal Close Average value of 4 Save the average value after taking the average
type setting : PNP Normal Open : PNP Normal Close HIGH peaks of the 4 saved HIGH peak values
: Normal Open
1st value of LOW peak Save the fourth lowest number of the measured value
Output mode setting
IN A s start 2nd value of LOW peak Save the third lowest number of the measured value
compensation timer
setting 3rd value of LOW peak Save the second lowest number of the measured value
IN B s start
compensation timer 4th value of LOW peak Save the lowest number of the measured value
setting Save the average value after taking the average
Average value of 4
IN A s Auto Zero of the 4 saved LOW peak values
LOW peaks
timer setting
Erase the memory of
Erase all the saved values
the peak value