Professional Documents
Culture Documents
10 Tips For Laser Engraving and Cutting - YoraHome
10 Tips For Laser Engraving and Cutting - YoraHome
SHOP BLOG
JOIN THE
REVIEWS ABOUT YO R A H O M E CART
C LU B
FAQ
1. Stay Safe
Take care of your eyes! Appropriate eye protection needs to be worn to avoid
serious & permanent damage to your eyesight.
NEVER LOOK DIRECTLY INTO ANY LASER BEAM. Choose goggles appropriate to
your machine.
For the Yorahome range of lasers, these Blue-Violet Laser Protective Goggles 200-
540nm are perfect, and each machine comes supplied with 1 pair. You can order
extra ones for family or friends to be able to watch you at work.
Ventilate the work area. Laser engraving and cutting can generate smoke & fumes,
make sure your work area is well ventilated and that you can get rid of any smoke
or smell.
https://yorahome.com/pages/10-tips-for-laser-engraving-and-cutting 1/9
29/01/2021 10 Tips For Laser Engraving And Cutting – YoraHome
Never leave the working laser unattended. You can adjust settings or turn off the
laser if you need to if you are with it, you can’t if you’re not there.
You need to ensure that your work piece is aligned to the movement of the
machine.
You can mark up the available work area as a grid and align the work piece on
there, that way your engraving or cutting will be where you want it to be.
Do not use the piece you intend to make the finished article from to start with!
Use a scrap piece of the same material to get your settings right first.
https://yorahome.com/pages/10-tips-for-laser-engraving-and-cutting 2/9
29/01/2021 10 Tips For Laser Engraving And Cutting – YoraHome
You can make fine setting changes once the job starts but getting the settings as
close as you need to begin with saves a lot of heartache and firewood.
For example, natural wood is not uniform. The grain represents different growth
periods and will burn differently, darker bits are harder and lighter bits softer – this
can lead to a “zebra” pattern as below.
You can often get a better result from a good plywood if you after a clear, crisp
engraving.
But remember, wood isn’t the only thing you can use your laser on. General guides
for what you can engrave depending on power are as follows:
https://yorahome.com/pages/10-tips-for-laser-engraving-and-cutting 3/9
29/01/2021 10 Tips For Laser Engraving And Cutting – YoraHome
Make sure the material you choose is safe to cut or engrave, as some plastics can
produce hazardous chemicals when burned.
5. Choose a good image
Depending on the software you are using with your machine, you can import
different formats.
With the YoraHome Laser Engraving Machine 6550, the most commonly used
software is LaserGRBL, and through the image import function, you can use bmp,
jpg, png and gif file format as well as Gcode.
You can use photographs, diagrams, text, whatever you want to try.
6. Focus
Probably the thing that will affect the quality of your engraving or cutting will be
whether you have focused the beam correctly.
You are aiming to adjust the beam to the smallest & sharpest pinpoint you can
achieve. Don’t go too far as it will start to distort again.
https://yorahome.com/pages/10-tips-for-laser-engraving-and-cutting 4/9
29/01/2021 10 Tips For Laser Engraving And Cutting – YoraHome
You may need to adjust the height of your material to get a small enough beam,
you can use our adjustable lifting platform to bring your material closer to the laser,
rather than getting the laser closer to the material.
7. Mask
Using masking paper over acrylic stops the immediate reflection of the laser.
Masking wood and leather can prevent charring around the edges of the burn.
Always try your setting out on a piece of scrap first, to see if masking will be useful
or not.
Finding your starting position is much easier when you use framing tools.
In LaserGRBL, you can use custom buttons to set up a framing tool, turn your laser
on and off and a number of other useful actions.
https://yorahome.com/pages/10-tips-for-laser-engraving-and-cutting 5/9
29/01/2021 10 Tips For Laser Engraving And Cutting – YoraHome
This will draw the area on your material that your image is going to take up, so you
can check you are centred and ready to go.
9. Take notes
Make a note of everything you do: the material used, the size of the image, the
settings you used, whether the result came out as expected, the time it took and so
on.
Keep a notebook at the side of your machine and try to enter something every
time you use the machine, that way you can always refer back to what you’ve done
previously.
10. Practice
https://yorahome.com/pages/10-tips-for-laser-engraving-and-cutting 6/9
29/01/2021 10 Tips For Laser Engraving And Cutting – YoraHome
The best and most important tip for using your laser engraver and cutter is to
practice. You will never get any worse at doing something by practicing. You will
only improve your techniques.
https://yorahome.com/pages/10-tips-for-laser-engraving-and-cutting 7/9
29/01/2021 10 Tips For Laser Engraving And Cutting – YoraHome
FREE EXPRESS
DELIVERY!
Free & Fast Delivery Worldwide With shipping
companies like DHL Express, UPS, FedEx Express,
USPS, Canada Post, Royal Mail & TNT.
https://yorahome.com/pages/10-tips-for-laser-engraving-and-cutting 8/9
29/01/2021 10 Tips For Laser Engraving And Cutting – YoraHome
HAVE
QUESTIONS?
We're happy to help!
Send an email at support@yorahome.com or call 833-541-5997
for sales inquiries & 833-861-3193 for technical support.
Email SUBSCRIBE
COMPANY SHOP SUPPORT & LEARN
Terms Of Service
© 2018-2020 YoraHome. All Rights Reserved.
https://yorahome.com/pages/10-tips-for-laser-engraving-and-cutting 9/9