Professional Documents
Culture Documents
Standard STD 5051,16: Text Marking On Parts
Standard STD 5051,16: Text Marking On Parts
Volvo Group
The English language version is the original and the reference in case of dispute.
Orientation
This issue differs from issue 16 in that:
- it has been clarified that the standard covers both Volvo Group brands as well as joint venture
brands.
- section 3.3 has been revised to comply with European competition legislation.
- sections 6.6 and 6.7, which describe free-text marking and supplementary marking, respectively,
have been added.
- the option to perform the VOLVO PENTA marking on a single line has been added in section 8.4.
- the reference to figures for date clock in table 3 have been changed from 4a and 5a to 3a and 4a,
respectively.
© AB Volvo Group. All rights reserved. The Standard may not be used, reproduced, transmitted or made available
to a third party without prior written permission. Printed copies are uncontrolled. Print date: 2020-05-26
Standard STD 5051,16
Volvo Group
Contents
1 Scope and field of application ......................................................................................................... 3
2 Terms and definitions ....................................................................................................................... 3
3 Location and visibility....................................................................................................................... 3
3.1 General ................................................................................................................................................ 3
3.2 Volvo Group and joint venture brand markings ................................................................................... 3
3.3 Supplier brand marking – when applicable ......................................................................................... 4
3.4 Supplier serial number ........................................................................................................................ 4
4 Indication of marking in design-engineering documentation ...................................................... 4
5 Marking methods............................................................................................................................... 6
6 Basic markings .................................................................................................................................. 7
6.1 Volvo brand marking ........................................................................................................................... 8
6.2 Part number......................................................................................................................................... 8
6.3 Country of origin .................................................................................................................................. 8
6.4 Special requirements for the United States ........................................................................................ 8
6.5 Designations ........................................................................................................................................ 8
6.6 Free-text marking ................................................................................................................................ 9
6.7 Supplementary marking ...................................................................................................................... 9
7 Supplementary markings ............................................................................................................... 12
8 Brand marking and text requirements .......................................................................................... 15
8.1 Relative position of brand marking and text on marked part ............................................................ 16
8.2 Text style for other text ...................................................................................................................... 16
8.3 Colours .............................................................................................................................................. 17
8.4 VOLVO and VOLVO PENTA ............................................................................................................ 17
8.5 UD TRUCKS ..................................................................................................................................... 20
8.6 SDLG ................................................................................................................................................. 24
8.7 RENAULT TRUCKS .......................................................................................................................... 26
8.8 PREVOST ......................................................................................................................................... 29
8.9 NOVABUS ......................................................................................................................................... 30
8.10 MACK ................................................................................................................................................ 31
8.11 EICHER ............................................................................................................................................. 35
8.12 ARQUUS ........................................................................................................................................... 38
9 Associated standards ..................................................................................................................... 42
Appendix A Marking examples ............................................................................................................. 43
Appendix B Discontinued basic markings .......................................................................................... 47
Appendix C Discontinued supplementary markings .......................................................................... 48
Appendix D Discontinued Volvo wordmark sizes ............................................................................... 50
© AB Volvo Group. All rights reserved. The Standard may not be used, reproduced, transmitted or made available
to a third party without prior written permission. Printed copies are uncontrolled. Print date: 2020-05-26
Standard STD 5051,16
Volvo Group
The standard applies to direct marking on parts. In relevant sections, it may also be used for indirect
marking, such as marking of packages.
Marking may include Aftermarket branding levels 1–3, in accordance with the Brand Distinction and
Aftermarket Tool (BDAT), when requested by either a Volvo Group brand or a joint venture brand.
In cases where the supplier shall specify a supplier-part marking in the supplier-provided documentation,
in accordance with this standard, such marking shall be specified upon request from and require the
approval of the Volvo Group.
If the manufacturer needs to put their own marking on a part, for example to facilitate handling, this can
be accepted by the responsible Volvo Group entity on condition that the function of the part is not
jeopardized. However, this marking shall be placed completely separate from the Volvo Group entity
marking. The supplier’s marking shall be approved by the Volvo Group entity.
3.1 General
The marking shall be located in such a way that the function of the part is not affected and the marking
must be legible when required.
Any application of the Volvo Group product emblems and wordmark logotypes must be approved by
Product Design and Aftermarket brand representatives.
© AB Volvo Group. All rights reserved. The Standard may not be used, reproduced, transmitted or made available
to a third party without prior written permission. Printed copies are uncontrolled. Print date: 2020-05-26
Standard STD 5051,16
Volvo Group
The symbol with its leader line shall be placed close to the relevant drawing view. The symbol shall
be numbered, starting with number one, even if the drawing only has one marking.
If different alternative requirements shall be indicated they shall be performed as shown by the example in
figure 1.
Fig 1
© AB Volvo Group. All rights reserved. The Standard may not be used, reproduced, transmitted or made available
to a third party without prior written permission. Printed copies are uncontrolled. Print date: 2020-05-26
Standard STD 5051,16
Volvo Group
If several different markings as per this standard shall be indicated, or if there is a need to split a marking
in different locations, they shall be considered separate marking requirements and thereby be indicated
separately, as shown by the example in figure 2a.
If the marking area shall be limited, this must be indicated with a long-dashed, double-dotted, narrow line.
Its dimension and placement shall be given in accordance with the example in figure 2a.
For indication of the opposite (hidden) surface, a dashed leader line is used as per figure 2b.
Fig. 2a Fig. 2b
The marking requirement as such shall be documented in the PDM system for the part concerned. If the
PDM system lacks this functionality, the marking requirement shall be documented on the drawing or in a
technote.
Supplementary markings 7 3
Basic marking 6 2
Marking method 5 1
Fig. 3
If the marking text shall be read in a specific direction, an arrow showing the reading direction shall be
indicated, see figure 2a.
© AB Volvo Group. All rights reserved. The Standard may not be used, reproduced, transmitted or made available
to a third party without prior written permission. Printed copies are uncontrolled. Print date: 2020-05-26
Standard STD 5051,16
Volvo Group
5 Marking methods
The method number shall be indicated by one, two, or three digits, separated by point(s). If only one digit
has been given for a method comprising alternative marking variants as per table 1, any of the given
alternatives is acceptable.
When durable brand marking is required another method than specified in the table below may be
accepted, on condition that the brand marking is legible during the component’s entire life.
Table 1
Method No. Marking method Remarks
1 Marking in connection with casting, Parts and blanks formed by casting, injection
forging or other type of forming: moulding, forging or some other method.
© AB Volvo Group. All rights reserved. The Standard may not be used, reproduced, transmitted or made available
to a third party without prior written permission. Printed copies are uncontrolled. Print date: 2020-05-26
Standard STD 5051,16
Volvo Group
Table 1
Method No. Marking method Remarks
4 Adhesion: Non-durable marking method used, for instance, for
plastics and rubber parts and for components bought
in the finished stage.
6 Basic markings
This section describes the basic marking designations used for text marking on parts. In addition to this,
supplementary marking designations in accordance with section 7 can be used.
The general requirement is that the marking shall be kept together and structured as shown in section
8.1, figure 6. If lack of space makes this impractical, the marking shall be spread out and this shall be
indicated on the drawing by using multiple marking symbols (see figure 2a in section 4).
© AB Volvo Group. All rights reserved. The Standard may not be used, reproduced, transmitted or made available
to a third party without prior written permission. Printed copies are uncontrolled. Print date: 2020-05-26
Standard STD 5051,16
Volvo Group
Unless otherwise agreed, the complete indication of the country of origin shall be performed in capital
letters.
The name of the country of origin shall correspond to the short name in English as stated in ISO 3166-1,
List one, first column.
No abbreviation or alpha-2 code, alpha-3 code or numeric code of the country name is permitted. For
example, USA shall be indicated as “UNITED STATES”.
The country of origin marking shall be performed on one line. However, if the marking space is limited the
marking may be performed on a maximum of two lines, where the words “MADE IN” are printed on the
first line and the actual country name is printed on the second line.
According to Section 304 of the Tariff Act of 1930, all imported parts must have country of origin marking,
see Code of Federal Regulations, Title 19 - Custom Duties, Part 134 - Country of Origin Marking.
Note: If you have questions or want clarification to ensure correct adherence to the marking standard
related to country of origin, please e-mail your request to:
Info.USCustomsInquiries@volvo.com with "Country of Origin Marking Request" as the Subject.
6.5 Designations
Designations specifying country of origin without the mandatory prefix “MADE IN” shall not be used for
new design. These designations have been transferred to table B1 in Appendix B.
Other designations that shall not be used for new design have been transferred to table B1 in Appendix B.
© AB Volvo Group. All rights reserved. The Standard may not be used, reproduced, transmitted or made available
to a third party without prior written permission. Printed copies are uncontrolled. Print date: 2020-05-26
Standard STD 5051,16
Volvo Group
In these cases, a specification of what information to include in the marking shall be given. This
information shall be placed within quotation-marks.
Table 2
Designation Marking information Example
0 Free-text marking (refers to other marking
information than that specified by the other
designations given in this table).
99 Only supplementary marking
1G The VOLVO brand mark 1) + part number + country
of origin
12345678
MADE IN SWEDEN
2 The VOLVO brand mark 1) + part number
3G The VOLVO brand mark 1) + country of origin
4G Part number + country of origin
5 The VOLVO brand mark 1)
6 Part number
12345678
7G Country of origin MADE IN SWEDEN
8 Text: Made by XXXXX for YYYYY 2)
17G The UD TRUCKS brand mark 1) + part number +
country of origin
12345678
MADE IN JAPAN
18 The UD TRUCKS brand mark 1) + part number
19G The UD TRUCKS brand mark 1) + country of origin
20 The UD TRUCKS brand mark 1)
© AB Volvo Group. All rights reserved. The Standard may not be used, reproduced, transmitted or made available
to a third party without prior written permission. Printed copies are uncontrolled. Print date: 2020-05-26
Standard STD 5051,16
Volvo Group
Table 2
Designation Marking information Example
23G The RENAULT TRUCKS brand mark 1) + part
number + country of origin
12345678
MADE IN FRANCE
24 The RENAULT TRUCKS brand mark 1) + part
number
25G The RENAULT TRUCKS brand mark 1) + country of
origin
26 The RENAULT TRUCKS brand mark 1)
27G The EICHER brand mark 1) + part number + country
of origin
12345678
MADE IN INDIA
28 The EICHER brand mark 1) + part number
29G The EICHER brand mark 1) + country of origin
30 The EICHER brand mark 1)
12345678
MADE IN UNITED STATES
32 The MACK brand mark 1) + part number
33G The MACK brand mark 1) + country of origin
34 The MACK brand mark 1)
12345678
MADE IN CHINA
36 The SDLG brand mark 1) + part number
© AB Volvo Group. All rights reserved. The Standard may not be used, reproduced, transmitted or made available
to a third party without prior written permission. Printed copies are uncontrolled. Print date: 2020-05-26
Standard STD 5051,16
Volvo Group
Table 2
Designation Marking information Example
37G The SDLG brand mark 1) + country of origin
38 The SDLG brand mark 1)
39G The PREVOST brand mark 1) + part number +
country of origin
12345678
MADE IN CANADA
40 The PREVOST brand mark 1) + part number
41G The PREVOST brand mark 1) + country of origin
42 The PREVOST brand mark 1)
43G The NOVA BUS brand mark 1) + part number +
country of origin
12345678
MADE IN CANADA
44 The NOVA BUS brand mark 1) + part number
45G The NOVA BUS brand mark 1) + country of origin
46 The NOVA BUS brand mark 1)
12345678
MADE IN FRANCE
48 The ARQUUS brand mark 1) + part number
49G The ARQUUS brand mark 1) + country of origin
50 The ARQUUS brand mark 1)
1) Note the different types and clear-zone requirements (see section 8).
2) XXXXX = Name or trademark of the supplier; YYYYY = Volvo Group entity
© AB Volvo Group. All rights reserved. The Standard may not be used, reproduced, transmitted or made available
to a third party without prior written permission. Printed copies are uncontrolled. Print date: 2020-05-26
Standard STD 5051,16
Volvo Group
7 Supplementary markings
Table 3
Designation Marking information Example of marking Remarks
text
E Batch number Number that relates the product with all other units of
the same product from the same production batch.
F Serial number S/N: 1234ABCD Number assigned to an entity for its lifetime
H Change condition/ -1 -1 = part version 01
version suffix -2 = part version 02
etc. (acc. to the drawing or Part Version Report)
J Right-hand part RH Right Hand
© AB Volvo Group. All rights reserved. The Standard may not be used, reproduced, transmitted or made available
to a third party without prior written permission. Printed copies are uncontrolled. Print date: 2020-05-26
Standard STD 5051,16
Volvo Group
Table 3
Designation Marking information Example of marking Remarks
text
S4 Date of manufacture 150101 YearMonthDay
This indication is used when there is a need for
detailed traceability and method U is not an option.
Below are two examples of how this can be indicated:
YYMMDD, DDMMYY
- YY indicates the year in the current century
(e.g. 2015 = 15)
- MM indicates the month with two digits
(e.g. January = 01)
- DD indicates day of month
T Date of manufacture 10W03 YearWeek (with W in between and no spaces) W =
short for Week. Calendar week is represented by two
digits. The first calendar week of the year shall be
identified as 01 and subsequent weeks shall be
numbered in ascending sequence.
U Date of manufacture 10W031 YearWeekDay (with W in between and no spaces) W
= short for Week. Day of week is represented by one
digit. Monday shall be identified as day 1 of any
calendar week, and subsequent days of the same
week shall be numbered in ascending sequence to
Sunday (day 7).
V Date of manufacture (see figures 4a Date clock or date insert, alt. date field for cast or
and 4b) injection-moulded parts as per figures 4a and 4b (year
and month to be indicated).
X Date of manufacture (see figures 5a Date clock or date insert, alt. date field for cast or
and 5b) injection-moulded parts as per figures 5a and 5b (year
and month to be indicated).
Y Date of manufacture Date clock or date insert, alt. date field as per V or X
but with other dimensions (dimensioned on drawing)
(year and month to be indicated).
Z Compressed code 12R345 6 characters. Only used upon request from the
manufacturing unit if there is insufficient space for
complete marking. (Supplier code + RH or LH part +
batch number, consecutive).
© AB Volvo Group. All rights reserved. The Standard may not be used, reproduced, transmitted or made available
to a third party without prior written permission. Printed copies are uncontrolled. Print date: 2020-05-26
Standard STD 5051,16
Volvo Group
Figures 4a, 4b, 5a and 5b shall be regarded as explanatory figures, and other designs are therefore
accepted (shall be approved by the Volvo Group entity concerned). Tolerance zone 2 mm.
The date fields as per figures 4b and 5b shall comprise a ten-year period, starting with the year the part
was first manufactured in the top left-hand square.
Date clock or date insert V (2013 January indicated) Date field V (new part in 2011 June, last date of
manufacture 2012 March indicated)
Fig. 4a Fig. 4b
Date clock or date insert X (2013 February indicated) Date field X (new part in 2011 August, last date of
manufacture 2012 March indicated)
Fig. 5a Fig. 5b
© AB Volvo Group. All rights reserved. The Standard may not be used, reproduced, transmitted or made available
to a third party without prior written permission. Printed copies are uncontrolled. Print date: 2020-05-26
Standard STD 5051,16
Volvo Group
Suppliers can obtain the brand markings in a suitable file format by requesting it from their Volvo Group
contact.
If the marking contains a brand mark, the specified size in the designation refers to the brand mark. When
there are different marking alternatives for a brand, the required marking shall be indicated by a prefix as
per the relevant table.
Whenever a brand mark has a wordmark or a text element, this shall act as a guide for the text height of
the other information. The text height (H1 and H2) of the other information shall be smaller than the height
(H) of the brand marking. See tables for the respective brands.
Requirements concerning text height (H1 and H2, respectively) can be found in the table for each brand.
For definition of text heights for different information, see figure 6 in section 8.1 Relative position of text on
marked part.
Parts exposed to dirt, underseal or similar shall have a minimum text height of 4 mm for legibility reasons.
Normally, the combination 6/4 for H1/ H2 should be used for such parts.
Note: Should this combination not be possible due to lack of space, a text height of 4 mm shall be
specified for all text. This must, however, be specified for each marking information, i.e.
Identification data, manufacturing data and country of origin.
© AB Volvo Group. All rights reserved. The Standard may not be used, reproduced, transmitted or made available
to a third party without prior written permission. Printed copies are uncontrolled. Print date: 2020-05-26
Standard STD 5051,16
Volvo Group
1) According to the relevant trademark requirements or guidelines. See section for each brand.
2) Additional manufacturing data other than country of origin
Fig. 6
If one (or some) of the intermediate lines is not used, the lower one(s) shall be moved up a step (or two).
If some information in the horizontal plane is left out, the remaining data shall be moved to the left to
produce a straight left margin.
For products where left-aligned text is not suitable from an aesthetic viewpoint, centred text is acceptable
(this shall, however, require approval by the Volvo Group entity concerned).
If the number of lines is restricted due to lack of space, this shall be indicated on the drawing. In such
case, e.g. “two lines” shall be indicated after the marking information.
If more than one line is prescribed, the brand marking shall always be placed by itself on the top line.
If only identity data and manufacturing information are specified, the size refers to the text height of the
identity data (H1). In these cases, the clearance all around the marking shall be equal to at least half the
specified height H1 of the marking.
© AB Volvo Group. All rights reserved. The Standard may not be used, reproduced, transmitted or made available
to a third party without prior written permission. Printed copies are uncontrolled. Print date: 2020-05-26
Standard STD 5051,16
Volvo Group
8.3 Colours
For a correct representation of the Volvo Group corporate colours, the information provided at Brand
Center on the Volvo Group Intranet shall be used.
Suppliers can obtain the information about corporate colours from their Volvo Group contact.
When printed, the VOLVO or the VOLVO PENTA wordmark shall always be represented in one of its
corporate colours.
When printed, the NOVA BUS logotype must always be represented in black.
If no colour requirement has been specified on the drawing, the marking text shall be applied “colourless”
(in the case of marking methods 1, 2, or 6).
If the drawing specifies one single colour (black or white), this refers to the colour of the text and the
surrounding surface is “colourless” (= substrate colour).
In the case of marking method 5 (stamping, stencilling or painting), and if no colour has been specified,
the marking shall be made black or white and shall contrast with the colour of the substrate.
Unless otherwise stated, the colour requirement for brand marking also applies to the marking text.
When marking materials that, for some reason, do not permit the use of filled letters (e.g. hard materials),
the letters may be produced with contour lines. See figures 8a and 8b. A suitable thickness for the
contour lines is 1/100 of the length/width of the logotype. Contour lines may not be used in any other
context.
© AB Volvo Group. All rights reserved. The Standard may not be used, reproduced, transmitted or made available
to a third party without prior written permission. Printed copies are uncontrolled. Print date: 2020-05-26
Standard STD 5051,16
Volvo Group
The pre-determined clear zone around the VOLVO or the VOLVO PENTA wordmark shall be at least
equal to the height (X) of the VOLVO wordmark. See figures 9a and 9b.
Fig. 9a VOLVO wordmark clear zone Fig. 9b VOLVO PENTA wordmark clear zone
Note: In case of inadequate marking space, the clear zone may be equal to half the height of the
VOLVO wordmark.
The single-line VOLVO PENTA branding defined below may, after approval by the product design
department, be used if the available space is unsuitable for dual-line branding.
The minimum width of the VOLVO PENTA single-line wordmark shall be 27 mm, see figure 10.
The pre-determined clear zone around the VOLVO PENTA single-line wordmark shall be at least equal to
the height (X) of the VOLVO wordmark. See figure 10.
© AB Volvo Group. All rights reserved. The Standard may not be used, reproduced, transmitted or made available
to a third party without prior written permission. Printed copies are uncontrolled. Print date: 2020-05-26
Standard STD 5051,16
Volvo Group
VOLVO wordmark
H = 0,13 × W
VOLVO PENTA
wordmark
(two lines) H = 0,12 × W
VOLVO PENTA
wordmark H = 0,06 × W
(one line)
Table 5
The VOLVO brand mark Text height H1 Text height H2
(line 2) (lines 3 and 4)
VOLVO VOLVO VOLVO
wordmark PENTA PENTA
wordmark wordmark
(two lines) (one line)
Height Width Width Width Tol Nominal Tol Nominal Tol
approx. [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm]
[mm]
1,2 0,1 0,8 0,1
1,6 A12,5 B13 C27 0,6 1,6 1
2 A15 B17 C33 0,8 2 1,2
2,6 A20 B22 C43 1 2,5 1,6
3,2 A25 B27 C54 1,2 3 0,2 2
3,9 A30 B33 C65 1,5 3,5 2,5
5,2 A40 B42 C86 2 5 3 0,2
6,5 A50 B53 C108 2,5 6 0,4 4
7,8 A60 B65 C130 3 7,5 5
10,4 A80 B87 C173 4 10 0,5 6 0,4
13 A100 B108 C217 5 12,5 8
16 A125 B133 C267 6 16 0,8 10 0,6
21 A160 B170 C346 8 20 12
© AB Volvo Group. All rights reserved. The Standard may not be used, reproduced, transmitted or made available
to a third party without prior written permission. Printed copies are uncontrolled. Print date: 2020-05-26
Standard STD 5051,16
Volvo Group
8.5 UD TRUCKS
The UD Trucks brand mark is comprised of the brand symbol and the wordmark.
On parts where a UD Trucks brand marking cannot be executed at its minimum size in accordance with
this standard, the symbol by itself can be permitted (see figure 16). The choice of execution should be
based on the available space on each specific part.
Vertical use of the brand mark shall be given precedence.
Use of the UD Trucks brand mark shall be made in accordance with the following preference:
1. UD brand mark in vertical format, see figure 12
2. UD brand mark in horizontal format, see figure 14
3. UD logotype, see figure 16
4. UD symbol, see figure 17
For questions regarding the use of the UD Trucks brand mark, please contact Kenneth Hagas
kenneth.hagas@udtrucks.com.
8.5.1 Application
Use of the UD TRUCKS brand mark must comply with the latest issue of the UD Trucks brand guideline
A_Basic elements 6.1.
This must be followed in order to reproduce the brand mark accurately.
The minimum dimension of the UD TRUCKS brand mark in vertical format shall be in accordance with
figure 12.
© AB Volvo Group. All rights reserved. The Standard may not be used, reproduced, transmitted or made available
to a third party without prior written permission. Printed copies are uncontrolled. Print date: 2020-05-26
Standard STD 5051,16
Volvo Group
The relative size of each brand mark element and the established minimum clear zone around the brand
mark shall be in accordance with figure 13.
Fig. 13 UD TRUCKS brand mark, vertical format, relative size and clear zone
The minimum dimension of the UD Trucks brand mark in horizontal format shall be in accordance with
figure 14.
© AB Volvo Group. All rights reserved. The Standard may not be used, reproduced, transmitted or made available
to a third party without prior written permission. Printed copies are uncontrolled. Print date: 2020-05-26
Standard STD 5051,16
Volvo Group
The relative size of each brand mark element and the established minimum clear zone around the brand
mark shall be in accordance with figure 15.
Fig. 15 UD TRUCKS brand mark, horizontal format, relative size and clear zone
The minimum dimension of the UD TRUCK wordmark shall be in accordance with figure 16.
The minimum dimension of the UD TRUCKS symbol shall be in accordance with figure 17.
© AB Volvo Group. All rights reserved. The Standard may not be used, reproduced, transmitted or made available
to a third party without prior written permission. Printed copies are uncontrolled. Print date: 2020-05-26
Standard STD 5051,16
Volvo Group
UD TRUCKS
vertical brand mark
(Type A)
H = 0,11 × W
UD TRUCKS
horizontal brand
mark H = 0,08 × W
(Type B)
UD TRUCKS
brand logotype H = 0,11 × W
(Type C)
UD TRUCKS
brand symbol
(Type D) H = 0,29 × W
All dimensions of the UD brand mark are based on the brand symbol height that is described in the UD
Trucks Identity Guideline.
Table 6
The UD TRUCKS brand marks Text height H1 Text height H2
(line 2) (lines 3 and 4)
Type A Type B Type C Type D Nominal Tol Nominal Tol
Size Size Size Size [mm] [mm] [mm] [mm]
(Width) (Width) (Width) (Width)
A13 C13 1,2 0,1 0,8 0,1
A18 C18 2 1,2
A25 B25 C25 2,5 1,6
A30 B43 C30 3 0,2 2
A35 B50 C35 D6 4 2,5
A45 B65 C45 D7 5 3 0,2
A55 B75 C55 D8 6 0,4 4
A75 B100 C75 D11 8 5
A90 B125 C90 D13 10 0,5 6 0,4
A115 B155 C115 D17 12,5 8
A145 B200 C145 D22 16 0,8 10 0,6
A185 B250 C185 D30 20 12
© AB Volvo Group. All rights reserved. The Standard may not be used, reproduced, transmitted or made available
to a third party without prior written permission. Printed copies are uncontrolled. Print date: 2020-05-26
Standard STD 5051,16
Volvo Group
8.6 SDLG
For questions regarding the use of the SDLG brand mark, please contact:
shaohua.guo@sdlg.com.cn.
In accordance with the SDLG CORPORATE IDENTITY MANUAL, the pre-determined clear zone around
the logotype shall be at least equal to half the width of the logotype. See figure 19.
© AB Volvo Group. All rights reserved. The Standard may not be used, reproduced, transmitted or made available
to a third party without prior written permission. Printed copies are uncontrolled. Print date: 2020-05-26
Standard STD 5051,16
Volvo Group
Table 7
The SDLG Text height H1 Text height H2
brand mark (line 2) (lines 3 and 4)
(Width) Nominal Tol Nominal Tol
[mm] [mm] [mm] [mm] [mm]
1,2 0,1 0,8 0,1
10 2 1,2
15 2,5 1,6
20 3 0,2 2
25 4 2,5
30 5 3 0,2
35 6 0,4 4
45 8 5
55 10 0,5 6 0,4
65 12,5 8
85 16 0,8 10 0,6
105 20 12
© AB Volvo Group. All rights reserved. The Standard may not be used, reproduced, transmitted or made available
to a third party without prior written permission. Printed copies are uncontrolled. Print date: 2020-05-26
Standard STD 5051,16
Volvo Group
The established minimum clear zone around the logotype shall be equal to the height of the letter “R”, see
figure 21.
© AB Volvo Group. All rights reserved. The Standard may not be used, reproduced, transmitted or made available
to a third party without prior written permission. Printed copies are uncontrolled. Print date: 2020-05-26
Standard STD 5051,16
Volvo Group
The established minimum clear zone around the logotype shall be equal to the height of the letter “R”, see
figure 23.
The minimum clear zone for the RENAULT TRUCKS diamond shall be H1 according to table 8.
© AB Volvo Group. All rights reserved. The Standard may not be used, reproduced, transmitted or made available
to a third party without prior written permission. Printed copies are uncontrolled. Print date: 2020-05-26
Standard STD 5051,16
Volvo Group
RENAULT
TRUCKS wordmark
H = 0,17 × W
(two lines)
RENAULT
TRUCKS wordmark H = 0,09 × W
(one line)
RENAULT
TRUCKS diamond
Table 8
The RENAULT TRUCKS logotype Text height H1 Text height H2
RENAULT TRUCKS RENAULT TRUCKS RENAULT TRUCKS (line 2) (lines 3 and 4)
(two lines) (one line) diamond
Length Tol Length Tol Height Tol Nominal Tol Nominal Tol
[mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm]
C12 0,6 1,2 0,1 0,8 0,1
C14 0,6 1,6 1
A16 0,8 B30 1,5 C16 0,8 2 1,2
A20 1 B40 2 C20 1 2,5 1,6
A25 1,2 B50 2,5 3 0,2 2
A30 1,5 4 2,5
A40 2 5 3 0,2
A50 2,5 6 0,4 4
A60 3 8 5
A80 4 10 0,5 6 0,4
A100 5 12,5 8
A125 6 16 0,8 10 0,6
A160 8 20 12
© AB Volvo Group. All rights reserved. The Standard may not be used, reproduced, transmitted or made available
to a third party without prior written permission. Printed copies are uncontrolled. Print date: 2020-05-26
Standard STD 5051,16
Volvo Group
8.8 PREVOST
The clear zone is equal to 1,5 times the height of the Prevost logotype all around it. This dimension can
also be calculated using the rotated ’P’ of the Prevost logotype, see figure 27.
PREVOST
wordmark H = 0,08 × W
Table 9
The PREVOST wordmark Text height H1 Text height H2
(line 2) (lines 3 and 4)
Width Length Tol Nominal Tol Nominal Tol
approx. Nom (12,8xH) [mm] [mm] [mm] [mm] [mm]
[mm] [mm]
1,95 25 1,2 2 0,1 1,2 0,1
2,4 31 1,5 2,5 1,6
3,1 40 2 3 0,2 2
3,9 50 2,5 4 2,5
4,9 63 3 5 3 0,2
6,25 80 4 6 0,4 4
7,9 101 5 8 5
9,8 125 6 10 0,5 6 0,4
12,5 160 8 12,5 8
© AB Volvo Group. All rights reserved. The Standard may not be used, reproduced, transmitted or made available
to a third party without prior written permission. Printed copies are uncontrolled. Print date: 2020-05-26
Standard STD 5051,16
Volvo Group
8.9 NOVABUS
8.9.1 Brand mark size and clear zone
Sizes shall be chosen from table 10.
Note: Only the sizes specified in table 10 are allowed.
The minimum size of the NOVA BUS wordmark shall be 20 mm. See figure 28.
In accordance with the Nova Bus Guidelines, the pre-determined clear zone around the logotype shall be
at least equal to the height of the letter N of the wordmark. See figure 29.
NOVA BUS
wordmark H = 0,1 × W
Table 10
The NOVA BUS wordmark Text height H1 Text height H2
(line 2) (lines 3 and 4)
Width Length Tol Nominal Tol Nominal Tol
approx. Nom (10,2xH) [mm] [mm] [mm] [mm] [mm]
[mm] [mm]
1,6 16,2 0,8 1,6 0,1 1 0,1
2,1 21 1,1 2 1,2
2,6 26 1,3 2,5 1,6
3,2 32 1,6 3 0,2 2
4,1 42 2,1 4 2,5
5,2 53 2,6 5 3 0,2
6,5 66 3 6 0,4 4
8,2 83 4 8 5
10,4 106 5 10 0,5 6 0,4
13 132 7 12,5 8
© AB Volvo Group. All rights reserved. The Standard may not be used, reproduced, transmitted or made available
to a third party without prior written permission. Printed copies are uncontrolled. Print date: 2020-05-26
Standard STD 5051,16
Volvo Group
8.10 MACK
8.10.2 Application
The minimum dimension of the MACK wordmark shall be 12,7 mm, see figure 30.
Sizes shall be chosen from table 11.
Note: Only the sizes specified in table 11 are allowed.
© AB Volvo Group. All rights reserved. The Standard may not be used, reproduced, transmitted or made available
to a third party without prior written permission. Printed copies are uncontrolled. Print date: 2020-05-26
Standard STD 5051,16
Volvo Group
8.10.4 Application
The minimum dimension of the PURE MACK seal shall be 19 mm, see figure 32.
Sizes shall be chosen from table 11.
Note: Only the sizes specified in table 11 are allowed.
On parts where the PURE MACK seal cannot be executed at its minimum size in accordance with this
standard, either of these PURE MACK double-line or single-line executions is permitted, see figures 33a
and 33b. The double-line or single-line execution shall be chosen based on the available space on each
specific part.
Fig. 33a Minimum dimension of double line Fig. 33b Minimum dimension of single line
The use of either of these executions shall be indicated with the relevant prefix in table 11.
© AB Volvo Group. All rights reserved. The Standard may not be used, reproduced, transmitted or made available
to a third party without prior written permission. Printed copies are uncontrolled. Print date: 2020-05-26
Standard STD 5051,16
Volvo Group
The established minimum clear zone around the PURE MACK seal shall be equal to half the width of the
seal, see figure 34.
For the double-line or single-line brand marking, the minimum clear zone shall be equal to the width of the
letter “M”, see figures 35a and 35b.
Fig. 35a Double-line with clear zone Fig. 35b Single-line with clear zone
Manufactured and purchased assemblies shall be identified by the assembly number; component parts
shall not be identified. Items similar to engines, transmissions, differential carriers, and axles are an
exception. See section 6 Basic Marking and the examples given in Appendix A1.
In general, the PURE MACK seal trademark shall not be illustrated on the part drawing.
Below is an example of a part with both a brand marking that is visible to the customer (figure 36a) and a
required durable B-side (reverse side/back side/inside) marking (figure 36b).
FRONT BACK
© AB Volvo Group. All rights reserved. The Standard may not be used, reproduced, transmitted or made available
to a third party without prior written permission. Printed copies are uncontrolled. Print date: 2020-05-26
Standard STD 5051,16
Volvo Group
PURE MACK
wordmark H = 0,24 × W
(two lines)
PURE MACK
wordmark H = 0,12 × W
(one line)
Table 11
MACK PURE MACK Text height H1 Text height H2
wordmark (line 2) (lines 3 and 4)
seal wordmark wordmark
double line single line
Width Diameter Width Width Nominal Tol Nominal Tol
[mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm]
A12,7 1,2 0,1 1 0,1
A16 1,6 1
A19 D19 2 1,2
A22 2 1,2
A25 B19 C13 D22 2,5 1,6
A30 B22 C14,5 D27 3 0,2 2
A40 B28 C19 D38 4 2,5
A50 B36 C24 D49 5 3 0,2
A60 B43 C29 D55 6 0,4 4
A80 B55 C37 D72 8 5
A100 B68 C46 D90 10 0,5 6 0,4
A125 B83 C56 D111 12,5 8
© AB Volvo Group. All rights reserved. The Standard may not be used, reproduced, transmitted or made available
to a third party without prior written permission. Printed copies are uncontrolled. Print date: 2020-05-26
Standard STD 5051,16
Volvo Group
8.11 EICHER
Types A and B shall only be used in case of insufficient space on the part.
The different types of EICHER brand markings are indicated by using the designations found in table 12.
© AB Volvo Group. All rights reserved. The Standard may not be used, reproduced, transmitted or made available
to a third party without prior written permission. Printed copies are uncontrolled. Print date: 2020-05-26
Standard STD 5051,16
Volvo Group
The minimum width of the EICHER brand mark, type C, shall be 50 mm.
The clear zone around the logotype shall be at least equal to the height of the letter E in the wordmark.
See figure 38 for example.
© AB Volvo Group. All rights reserved. The Standard may not be used, reproduced, transmitted or made available
to a third party without prior written permission. Printed copies are uncontrolled. Print date: 2020-05-26
Standard STD 5051,16
Volvo Group
EICHER wordmark
(Type A) H = 0,19 × W
EICHER symbol 1)
(Type B) H = 0,38 × W
EICHER horizontal
logotype H = 0,12 × W
(Type C)
EICHER vertical
logotype
(Type D) H = 0,19 × W
1) In cases where the brand mark does not contain a wordmark or text, the height H = H1.
Table 12
The EICHER brand mark Text height H1 Text height H2
(line 2) (lines 3 and 4)
Type A Type B Type C Type D Nominal Tol Nominal Tol
Size Size Size Size [mm] [mm] [mm] [mm]
A10 B10 C10 D10 1,2 0,1 0,8 0,1
A12,5 B12,5 C12,5 D12,5 1,6 1
A15 B15 C15 D15 2 1,2
A20 B20 C20 D20 2,5 1,6
A25 B25 C25 D25 3 0,2 2
A30 B30 C30 D30 4 2,5
A40 B40 C40 D40 5 3 0,2
A50 B50 C50 D50 6 0,4 4
A65 B65 C65 D65 8 5
A80 B80 C80 D80 10 0,5 6 0,4
A100 B100 C100 D100 12,5 8
A125 B125 C125 D125 16 0,8 10 0,6
A135 B135 C135 D135 18 11
A145 B145 C145 D145 20 12
A200 B200 C200 D200 22 1,0 13 0,8
© AB Volvo Group. All rights reserved. The Standard may not be used, reproduced, transmitted or made available
to a third party without prior written permission. Printed copies are uncontrolled. Print date: 2020-05-26
Standard STD 5051,16
Volvo Group
8.12 ARQUUS
The minimum dimension of the ARQUUS wordmark shall be 30 mm, see figure 39b.
© AB Volvo Group. All rights reserved. The Standard may not be used, reproduced, transmitted or made available
to a third party without prior written permission. Printed copies are uncontrolled. Print date: 2020-05-26
Standard STD 5051,16
Volvo Group
The minimum dimension of the ARQUUS monogram shall be 20 mm, see figure 39c.
Use of the ARQUUS circled monogram, see figure 39d, is restricted. Contact the ARQUUS Brand
Management Team for further information about minimum dimensions and clear zones.
The clear zone around the ARQUUS brand marking shall be at least equal to the size of the triangle in the
centre of the monogram. See figures 40a, 40b and 40c for examples.
© AB Volvo Group. All rights reserved. The Standard may not be used, reproduced, transmitted or made available
to a third party without prior written permission. Printed copies are uncontrolled. Print date: 2020-05-26
Standard STD 5051,16
Volvo Group
© AB Volvo Group. All rights reserved. The Standard may not be used, reproduced, transmitted or made available
to a third party without prior written permission. Printed copies are uncontrolled. Print date: 2020-05-26
Standard STD 5051,16
Volvo Group
ARQUUS logotype
H = 0,13 × W
ARQUUS wordmark
H = 0,13 × W
ARQUUS
monogram 1)
H = 0,19 × W
ARQUUS circled
monogram 1)
H = 0,15 × W
1) In cases where the brand mark does not contain a wordmark or text, the height H = H1.
Table 13
The ARQUUS brand mark Text height H1 Text height H2
(line 2) (lines 3 and 4)
ARQUUS ARQUUS ARQUUS ARQUUS Nominal Tol Nominal Tol
logotype wordmark monogram circled [mm] [mm] [mm] [mm]
monogram
Width Width Width Width Nominal Tol Nominal Tol
[mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm]
1,2 0,1 0,8 0,1
1,6 1
A20 B20 C14 D17 2 1,2
A25 B25 C17 D21 2,5 1,6
A30 B30 C20 D25 3 0,2 2
A35 B35 C25 D31 4 2,5
A40 B40 C30 D37 5 3 0,2
A50 B50 C40 D50 6 0,4 4
A60 B60 C50 D62 7 5
A70 B70 C60 D75 8 6 0,4
A80 B80 C70 D87 10 0,5 6
A100 B100 C90 D112 12,5 8
© AB Volvo Group. All rights reserved. The Standard may not be used, reproduced, transmitted or made available
to a third party without prior written permission. Printed copies are uncontrolled. Print date: 2020-05-26
Standard STD 5051,16
Volvo Group
9 Associated standards
STD 920-0001 Representation of dates and times
STD 103-0002 Generic identification and marking of plastics products
STD 103-0010 Marking of aluminium parts
STD 103-0026 Marking of magnesium parts
STD 103-0013 Parts marking with bar codes and 2D symbologies
STD 103-0020 Marking on filters
STD 5052,21 Colour identification marking on rubber parts
ISO 3166-1 Codes for the representation of names of countries and their subdivisions
DIN 1451 Serifenlose Linear-Antigua
© AB Volvo Group. All rights reserved. The Standard may not be used, reproduced, transmitted or made available
to a third party without prior written permission. Printed copies are uncontrolled. Print date: 2020-05-26
Standard STD 5051,16
Volvo Group
Example 1
For parts with common design-engineering documentation (e.g. multi-part drawings) but different
trademarks, this shall be indicated in accordance with the following example:
1) For part number 12345671:
MARKED ACCORDING TO STD 5051,16
MET 1.1 – 1G – A50
Example 2
MARKED ACCORDING TO STD 5051,16
MET 1.1 – 1G – P – A30
MARKED WITH PART NUMBER 12345678
Means: Marking method/Marking text raised – Basic marking/The VOLVO brand mark + part
number + country of origin – Additional markings/P = Supplier ID – Logotype size/A30 (indicates
VOLVO wordmark). For other text heights, see table 5.
It also illustrates marking with a part number that differs from the one that applies to the part in question,
for instance the assembly number.
Example 3
MARKED ACCORDING TO STD 5051,16
MET 1.1 – 0 – 6
ABCD 12345678
Means: Marking method/Marking text raised on the finished part – Free-text marking – Text height
(mm)/6
© AB Volvo Group. All rights reserved. The Standard may not be used, reproduced, transmitted or made available
to a third party without prior written permission. Printed copies are uncontrolled. Print date: 2020-05-26
Standard STD 5051,16
Volvo Group
Example 4
The example above illustrates how to indicate that the marking shall be spread out on the part.
Means: Marking method/Marking text raised – Basic marking/The VOLVO brand mark +
part number – Logotype size/A30 (indicates VOLVO wordmark). For other text heights, see
table 5.
Example 5
MARKED ACCORDING TO STD 5051,16
MET 1.1 – 99 – KV – 6
MET 1.1 – 99 – JV – 6
Means: Marking method/Marking test raised – Basic marking/No basic marking – Additional markings/
K = LH design, J = RH design (symmetric-opposite), V = date of manufacture – Text height (mm)/6.
Example 6
MARKED ACCORDING TO STD 5051,16
MET 2.2.1/MET 3.2 – 2 – JPS2 – A50
Means: Marking method/Etching (with acid)/riveted plate – Basic marking/The VOLVO brand mark +
part number – Additional markings/J = Right-hand part (RH) P = Supplier ID, S2 = Date of
manufacture is indicated in the form of a date code in accordance with table 5 (e.g. 1994 January =
date code RA) – Logotype size/A50 (indicates VOLVO wordmark). For other text heights, see table 5.
Example 7
MARKED ACCORDING TO STD 5051,16
MET 2.5 – 23G – P – A50
Means: Marking method/Marking using a laser beam – Basic marking/The RENAULT TRUCKS brand
mark + part number + country of origin – Additional markings/P = Supplier ID – brand mark size/A50
(indicates RENAULT TRUCKS wordmark on two lines). For other text heights, see table 8.
© AB Volvo Group. All rights reserved. The Standard may not be used, reproduced, transmitted or made available
to a third party without prior written permission. Printed copies are uncontrolled. Print date: 2020-05-26
Standard STD 5051,16
Volvo Group
Example 8
MARKED ACCORDING TO STD 5051,16
MET 2.1.1 – 6 – 4
Example 9
MARKED ACCORDING TO STD 5051,16
MET 4.1 – 14 – E – B40
Means: Marking method/Label – Basic marking/The RENAULT TRUCKS brand mark + part number –
Additional markings/E = Batch number – Logotype size/B40 (indicates RENAULT TRUCKS wordmark
on one line). For other text heights, see table 8.
Example 10
MARKED ACCORDING TO STD 5051,16
MET 2.3.1 – 17G – T – A55
Means: Marking method/Engraving – Basic marking/The UD TRUCKS brand mark + part number +
country of origin – Additional markings/T = Date of manufacture – Logotype size/A55 (indicates UD
TRUCKS vertical logotype). For other text heights, see table 6.
Example 11
MARKED ACCORDING TO STD 5051,16
MET 2.1.2 – 27G – T – D50
Means: Marking method/Embossing – Basic marking/The EICHER brand mark + part number +
country of origin – Additional markings/T = Date of manufacture – Logotype size/D50 (indicates
EICHER vertical logotype). For other text heights, see table 12.
Example 12
© AB Volvo Group. All rights reserved. The Standard may not be used, reproduced, transmitted or made available
to a third party without prior written permission. Printed copies are uncontrolled. Print date: 2020-05-26
Standard STD 5051,16
Volvo Group
Example 13
MARKED ACCORDING TO STD 5051,16
MET 2.1.3 – 27G – T – D65
Means: Marking method/Marking using a vibro pen – Basic marking/The EICHER brand mark + part
number + country of origin – Additional markings/T = Date of manufacture – Logotype size/D65
(indicates EICHER vertical logotype). For other text heights, see table 12.
Example 14
MARKED ACCORDING TO STD 5051,16
MET 4.1 – 14 – E – C20
Means: Marking method/Label – Basic marking/The RENAULT TRUCKS brand mark + part number –
Additional markings/E = Batch number – Logotype size/C20 (indicates RENAULT diamond). For other
text heights, see table 8.
© AB Volvo Group. All rights reserved. The Standard may not be used, reproduced, transmitted or made available
to a third party without prior written permission. Printed copies are uncontrolled. Print date: 2020-05-26
Standard STD 5051,16
Volvo Group
Table B1
Designation Marking information Example
1 The VOLVO brand mark 1) + part number + country
of origin
3 The VOLVO brand mark 1) + country of origin
4 Part number + country of origin
7 Country of origin only
9,10,11,12 Former MACK brand mark, not for new design.
13,14,15,16 Former Renault brand mark, not for new design.
17 The UD TRUCKS brand mark 1) + part number +
country of origin
19 The UD TRUCKS brand mark + country of origin
23 The RENAULT TRUCKS brand mark 1) + part
number + country of origin
25 The RENAULT TRUCKS brand mark + country of
origin
27 The EICHER brand mark 1) + part number + country
of origin
29 The EICHER brand mark + country of origin
31 The MACK brand mark 1) + part number + country
of origin
33 The MACK brand mark + country of origin
35 The SDLG brand mark 1) + part number + country
of origin
37 The SDLG brand mark 1) + country of origin
© AB Volvo Group. All rights reserved. The Standard may not be used, reproduced, transmitted or made available
to a third party without prior written permission. Printed copies are uncontrolled. Print date: 2020-05-26
Standard STD 5051,16
Volvo Group
Table C1
Designation Marking information Example of marking Remarks
text
A The VOLVO logotype PENTA Applies only to Volvo Penta.
Refers to the addition of "PENTA" to the VOLVO
logotype to obtain the trademark "VOLVO PENTA".
C RENAULT TRUCKS RENAULT TRUCKS Applies only to Renault Trucks. See section 8.3 for
logotype, on one line details. (If the former RENAULT logotype is still to be
used, the appendix applies.)
D RENAULT TRUCKS Applies only to Renault Trucks. See section 8.3 for
diamond details. (If the former RENAULT logotype is still to be
used, the appendix applies.)
The following was previously accepted as an alternative for indicating part version in accordance with
supplementary marking H, as per table 3
Fig. C1
© AB Volvo Group. All rights reserved. The Standard may not be used, reproduced, transmitted or made available
to a third party without prior written permission. Printed copies are uncontrolled. Print date: 2020-05-26
Standard STD 5051,16
Volvo Group
Table C2 Dimensions/design of relevant change field. For a definition of H1, see figure 7
H1 No. of lines No. of Size of square Square field Square field No. of
Line 2 squares/line height length changes
mm mm mm mm
2 1 12 a) 2 2 24 12
2,5 1 12 a) 2 2 24 12
3 1 12 a) 2 2 24 12
4 2 8 b) 2 4 16 16
5 2 8 b) 2,5 5 20 16
6 2 8 b) 3 6 24 16
8 3 5 c) 2,5 7,5 12,5 15
10 3 5 c) 3 9 15 15
12,5 3 5 c) 4 12 20 15
16 3 5 c) 4 12 20 15
20 3 5 c) 4 12 20 15
© AB Volvo Group. All rights reserved. The Standard may not be used, reproduced, transmitted or made available
to a third party without prior written permission. Printed copies are uncontrolled. Print date: 2020-05-26
Standard STD 5051,16
Volvo Group
Table D1
The VOLVO wordmark Text height H1 (line 2) Text height H2 (lines 3
and 4)
Height Length Tol Nominal Tol Nominal Tol
approx. Nom (7,7xH) [mm] [mm] [mm] [mm] [mm]
[mm] [mm]
1,3 10 0,5 1,2 0,1 0,8 0,1
© AB Volvo Group. All rights reserved. The Standard may not be used, reproduced, transmitted or made available
to a third party without prior written permission. Printed copies are uncontrolled. Print date: 2020-05-26