Professional Documents
Culture Documents
: 316100407-A-en
Sicherheitsforschung Gesellschaft m. b. H. Date: 08.11.2016
A - 4020 Linz, Petzoldstrasse 45 Page 2 of 103
Akkreditierte Prüf-,, Inspektions-
Inspektions und Zertifizierungsstelle Sponsor: PRTC
1. Introduction
This Classification Report defines the fire resistance class assigned to the construction
product "PROMASTOP®-CC" CC" in compliance with the procedures given in EN 13501-2:2007
13501
+ A1:2009.
2.1. Function:
The construction product "PROMASTOP®-CC" CC" is suitable for application in combination with
mineral wool boards (class A1 in accordance with EN 13501-1, melting point ≥ 1000 °C)
and is designated as a soft penetration seal for installation in horizontal and vertical
orientation in lightweight and rigid constructions. PROMASTOP®-CC is applicable as
firestop coating in combination
combination with cable trays, cable conductors, electrical cables,
combustible/non-combustible
combustible pipes with combustible/non-combustible
combustible/non combustible insulations as well as
linear joints/gap
/gap penetration seal.
seal. The function of the product is to resist fire in accordance
with typicall product reactions as described in clause 5 of EN 13501--2:2007+A1:2009.
2.2. Description:
The construction product "PROMASTOP®-CC" CC" is fully described in the test reports provided
in support of this Classification listed in clause 3.
2.2.1. Details:
"PROMASTOP®-CC"
CC" is available in
in one consistency and is designated as follows:
The technical data can be taken from the technical data sheet (Promat Fire stopping
handbook or please contact your local Promat office) and from the attachments to this
Classification Report.
No. 10 Square opening (1200 x 1200 mm) with cable assignment in compliance with EN
CG1-5 EI90 1366-3:2009
3:2009 (table A.1), cable groups 1-5.
1 Sealed with two mineral wool boards
coated with PROMASTOP®-CC CC (class A1, 50 mm, 150 kg/m³, melting point ≥ 1000
°C). Coating of overlapping cable, cable bundles an d cable trays with PROMASTOP®-
CC, length 100 mm, symmetrical to the supporting construction. Circumferential
coating of the opening
open of adjacent supporting construction:: 10 mm
No. 14 Square opening (1200 x 1200 mm) Sealed with two mineral wool boards coated with
EI120 PROMASTOP®-CC CC (class A1, 30 mm, 150 kg/m³, melting point ≥ 1000 °C).
Circumferential coating of the opening of adjacent supporting construction:
construction 10 mm
No. 34 Square opening (1200 x 1200 mm) with cable assignment in compliance with EN
CG1 E90 EI60
CG2 E90 EI60
1366-3:2009
3:2009 (table A.1). Sealed with two mineral wool boards coated with
CG3 E90 EI60 PROMASTOP®-CC CC (class A1, 30 mm, 150 kg/m³, melting point ≥ 1000 °C). Coating of
CG4 EI90
CG5 E90 EI60 overlapping cable, cable bundles and cable trays with PROMASTOP®-CC, length 100
mm, symmetrical to the supporting construction. Circumferential coating of the
opening of adjacent supporting construction: 10 mm
IBS – Institut für Brandschutztechnik und Classification Report No.: 316100407-A-en
Sicherheitsforschung Gesellschaft m. b. H. Date: 08.11.2016
A - 4020 Linz, Petzoldstrasse 45 Page 4 of 103
Akkreditierte Prüf-,, Inspektions-
Inspektions und Zertifizierungsstelle Sponsor: PRTC
Test setup: Rigid floor construction from aerated concrete; thickness 150 mm; density ≥
Test date: 27.07.2010 450 kg/m³.
No. 31 Asymmetrical linear joint with a width of 50 mm. Backfilling from 1K-PU
1K foam (class E):
E120 Top coating with PROMASTOP®-CC, CC, approx. 1 mm. Circumferential coating of joints to
EI60
adjacent supporting construction:
construction 10 mm
No. 32 Asymmetrical linear joint with a width of 50 mm. Backfilling from 1K-PU
1K foam (class E):
EI120 Bottom coating with PROMASTOP®-CC, CC, approx. 1 mm. Circumferential coating of joints
to adjacent supporting construction:
construction 10 mm
No. 31 Vertical, asymmetrical linear joint with a width of 50 mm. Backfilling from 1K-PU foam
EI90 (class E): Coating of fire-exposed
fire side with PROMASTOP®-CC, approx. 1 mm.
Circumferential coating of joints to adjacent supporting construction:
construction 10 mm
No. 32 Vertical, asymmetrical linear joint with a width of 50 mm. Backfilling from 1K-PU foam
EI90 (class E): Coating of fire-unexposed side with PROMASTOP®-CC, approx. 1 mm.
Circumferential coating of joints to adjacent supporting construction:
construction 10 mm
IBS – Institut für Brandschutztechnik und Classification Report No.: 316100407-A-en
Sicherheitsforschung Gesellschaft m. b. H. Date: 08.11.2016
A - 4020 Linz, Petzoldstrasse 45 Page 5 of 103
Akkreditierte Prüf-,, Inspektions-
Inspektions und Zertifizierungsstelle Sponsor: PRTC
Test setup: Rigid floor construction from aerated concrete; thickness 150 mm; density ≥
Test date: 11.01.2012 450 kg/m³.
No. 102 Metal pipe penetration seal: Opening in the soft penetration seal (PROMASTOP®-CC, 2
EI90 x 50 mm) Ø 80 mm with copper pipe Ø 18 / s 1.0 mm u/c and mineral wool insulation
(class A2,
40 kg/m³, melting point ≥ 1000 °C, 30 mm) in LS configuration with a total centred
penetration length of 600 mm.
No. 103 Metal pipe penetration seal: Opening in the soft penetration seal (PROMASTOP®-CC, 2
EI90 x 50 mm) Ø 105 mm with copper pipe Ø 42 / s 1.5 mm u/c and mineral
mine wool insulation
(class A2, 40 kg/m³, melting point ≥ 1000 °C, 30 mm) in LS configuration with a total
centred penetration length of 800 mm.
No. 104 Metal pipe penetration seal: Opening in the soft penetration seal (PROMASTOP®-CC, 2
EI90 x 50 mm) Ø 105 mm with copper pipe Ø 88.9 / s 2.0 mm u/c and mineral wool
insulation (class A2, 40 kg/m³, melting point ≥ 1000 °C, 30 mm) in LS configuration with
a total centred penetration length of 800 mm.
No. 105 Metal pipe penetration seal: Opening in the soft penetration seal (PROMASTOP®-CC, 2
EI90 x 50 mm) Ø 80 mm withwith steel pipe Ø 17 / s 2.0 mm u/c and mineral wool insulation
(class A2, 40 kg/m³, melting point ≥ 1000 °C, 30 mm) in LS configuration with a total
centred penetration length of 500 mm.
No. 106 ration seal (PROMASTOP®-CC, 2
Metal pipe penetration seal: Opening in the soft penetration
EI90 x 50 mm) Ø 105 mm with steel pipe Ø 42 / s 2.5 mm u/c and mineral
mine wool insulation
(class A2, 40 kg/m³, melting point ≥ 1000 °C, 30 mm) in LS configuration with a total
centred penetration length of 500 mm.
No. 107 Metal pipe penetration seal: Opening in the soft penetration seal (PROMASTOP®-CC, 2
EI90 x 50 mm) Ø 180 mm with steel pipe Ø 114 / s 3.6 mm u/c and mineral
mine wool insulation
(class A2, 40 kg/m³, melting point ≥ 1000 °C, 30 mm) in LS configuration with a total
centred
entred penetration length of 1000 mm.
No. 108 Metal pipe penetration seal: Opening in the soft penetration seal (PROMASTOP®-CC, 2
EI90 x 50 mm) Ø 280 mm with steel pipe Ø 220 / s 4.5 mm u/c and mineral
mine wool insulation
(class A2, 40 kg/m³, melting point ≥ 1000 °C, 30 mm) in LS configuration with a total
centred penetration length of 2500 mm.
No. 109 Metal pipe penetration seal: Opening in the soft penetration seal (PROMASTOP®-CC, 2
EI90 x 50 mm) Ø 220 mm with copper pipe Ø 18 / s 1.0 mm u/c and mineral wool insulation
(class A2, 40 kg/m³, melting point ≥ 1000 °C, 100 mm) in LS configuration with a total
centred penetration length of 600 mm.
No. 110 Metal pipe penetration seal: Opening in the soft penetration seal (PROMASTOP®-CC, 2
EI90 x 50 mm) Ø 245 mm with copper pipe Ø 42 / s 1.5 mm u/c and mineral
mine wool insulation
(class A2, 40 kg/m³, melting point ≥ 1000 °C, 100 mm) in LS configuration with a total
centred penetration length of 800 mm.
No. 111 Metal pipe penetration seal: Opening in the soft penetration seal (PROMASTOP®-CC, 2
EI90 x 50 mm) Ø 280 mm with copper pipe Ø 88.9 / s 2.0 mm u/c and mineral wool
insulation (class A2, 40 kg/m³, melting point ≥ 1000 °C, 100 mm) in LS configuration
with a total centred penetration length of 2000 mm.
IBS – Institut für Brandschutztechnik und Classification Report No.: 316100407-A-en
Sicherheitsforschung Gesellschaft m. b. H. Date: 08.11.2016
A - 4020 Linz, Petzoldstrasse 45 Page 6 of 103
Akkreditierte Prüf-,, Inspektions-
Inspektions und Zertifizierungsstelle Sponsor: PRTC
No. 112 Metal pipe penetration seal: Opening in the soft penetration seal (PROMASTOP®-CC, 2
EI90 x 50 mm) Ø 220 mm with steel pipe Ø 17 / s 2.0 mm u/c and mineral
mine wool insulation
(class A2, 40 kg/m³, melting point ≥ 1000 °C, 100 mm) in LS configuration with a total
centred penetration length of 500 mm.
No. 113 Metal pipe penetration seal: Opening in the soft penetration seal (PROMASTOP®-CC, 2
EI90 x 50 mm) Ø 245 mm with steel pipe Ø 42 / s 2.5 mm u/c and mineral
mine wool insulation
(class A2, 40 kg/m³, melting point
po ≥ 1000 °C, 100 mm) in LS configuration with a total
centred penetration length of 500 mm.
No. 114 Metal pipe penetration seal: Opening in the soft penetration seal (PROMASTOP®-CC, 2
EI90 x 50 mm) Ø 315 mm with steel pipe Ø 114 / s 3.6 mm u/c and mineral wool insulation
(class A2, 40 kg/m³, melting point ≥ 1000 °C, 100 mm) in LS configuration with a total
centred penetration length of 1000 mm.
No. 115 Metal pipe penetration seal: Opening in the soft penetration seal (PROMASTOP®-CC, 2
EI90 x 50 mm)) Ø 420 mm with steel pipe Ø 220 / s 4.5 mm u/c and mineral
mine wool insulation
(class A2, 40 kg/m³, melting point ≥ 1000 °C, 100 mm) in LS configuration with a total
centred penetration length of 2500 mm.
No. 146 Metal pipe penetration seal: Opening in n the soft penetration seal (PROMASTOP®-CC, 2
EI90 x 50 mm) Ø 150 mm with copper pipe Ø 88.9 / s 2.0 mm u/c and mineral wool
insulation (class A2, 100 kg/m³, melting point ≥ 1000 °C, 30 mm) in LS configuration
with a total centred penetration length of 2000 mm.
mm
No. 149 Metal pipe penetration seal: Opening in the soft penetration seal (PROMASTOP®-CC, 2
EI90 x 50 mm) Ø 175 mm with steel pipe Ø 114 / s 3.6 mm u/c and mineral
mine wool insulation
(class A2, 100 kg/m³, melting point ≥ 1000 °C, 30 mm) in LS configuration with a total
centred penetration length of 1000 mm.
No. 150 Metal pipe penetration seal: Opening in the soft penetration seal (PROMASTOP®-CC, 2
EI90 x 50 mm) Ø 220 mm with steel pipe Ø 159 / s 4.0 mm u/c and mineral
mine wool insulation
(class A2, 100 kg/m³, melting point ≥ 1000 °C, 30 mm) in LS configuration with a total
centred penetration length of 2500 mm.
No. 154 Metal pipe penetration seal: Opening in the soft penetration seal (PROMASTOP®-CC, 2
EI90 x 50 mm) Ø 315 mm with steel pipe Ø 114 / s 3.6 mm u/c and mineral wool insulation
(class A2, 100 kg/m³, melting point ≥ 1000 °C, 100 mm) in LS configuration with a total
centred penetration length of 1000 mm.
No. 155 Metal pipe penetration seal: Opening in the e soft penetration seal (PROMASTOP®-CC, 2
EI90 x 50 mm) Ø 360 mm with steel pipe Ø 159 / s 4.0 mm u/c and mineral
mine wool insulation
(class A2, 100 kg/m³, melting point ≥ 1000 °C, 100mm) in LS configuration with a total
centred penetration length of 2500 mm.
No. 200 Rectangular opening 1500 x 2800 mm with cable assignment in compliance with EN
CG1 EI90 1366-3:2009
3:2009 (table A.1). Sealed with two mineral wool boards coated with
CG2 EI90
CG3 EI90 PROMASTOP®-CC CC (class A1, 50 mm, 150 kg/m³, melting point. ≥ 1000 °C). Coating of
CG4 EI90 overlapping cables, cable bundles and cable trays with PROMASTOP®-CC, length 100
CG5 EI90 mm, symmetrical to the supporting construction. No circumferential coating of the
CG6 EI90
opening of the adjacent supporting construction.
IBS – Institut für Brandschutztechnik und Classification Report No.: 316100407-A-en
Sicherheitsforschung Gesellschaft m. b. H. Date: 08.11.2016
A - 4020 Linz, Petzoldstrasse 45 Page 7 of 103
Akkreditierte Prüf-,, Inspektions-
Inspektions und Zertifizierungsstelle Sponsor: PRTC
Test setup: Flexible wall construction; with a thickness of 100 mm; two layers of gypsum
Test date: 23.01.2012 plaster boards of 12.5 mm in acc. with EN 520; with backfilling from 40 mm
mineral wool acc. to class A1 (density 100 kg/m³).
No. 102 Metal pipe penetration seal: Opening in the soft penetration seal (PROMASTOP®-CC, 2
EI120 x 50 mm) Ø 80 mm with copper pipe Ø 18 / s 1.0 mm u/c and mineral wool insulation
(class A2, 40 kg/m³, melting point ≥ 1000 °C, 30 mm) in LS configuration with a total
centred
ntred penetration length of 600 mm.
No. 103 Metal pipe penetration seal: Opening in the soft penetration seal (PROMASTOP®-CC, 2
E120 x 50 mm) Ø 105 mm with copper pipe Ø 42 / s 1.5 mm u/c and mineral wool insulation
EI90
(class A2, 40 kg/m³, melting point ≥ 1000 °C, 30 mm) in LS configuration with a total
centred penetration length of 800 mm.
No. 104 Metal pipe penetration seal: Opening in the soft penetration seal (PROMASTOP®-CC, 2
E120 x 50 mm) Ø 150 mm with copper pipe Ø 88.9 / s 2.0 mm u/c and mineral wool
EI90
insulation (class A2, 40 kg/m³, melting point ≥ 1000 °C, 30 mm) in LS configuration with
a total centred penetration length of 2000 mm.
No. 105 Metal pipe penetration seal: Opening in the soft penetration seal (PROMASTOP®-CC, 2
EI120 x 50
0 mm) Ø 80 mm with steel pipe Ø 17 / s 2.0 mm u/c and mineral wool insulation
(class A2, 40 kg/m³, melting point ≥ 1000 °C, 30 mm) in LS configuration with a total
centred penetration length of 500 mm.
No. 106 Metal pipe penetration seal: Opening in the soft penetration seal (PROMASTOP®-CC, 2
EI120 x 50 mm) Ø 100 mm with steel pipe Ø 42 / s 2.5 mm u/c and mineral
mine wool insulation
(class A2, 40 kg/m³, melting point ≥ 1000 °C, 30 mm) in LS configuration with a total
centred penetration length of 500 mm.
No. 107 Metal pipe penetration seal: Opening in the soft penetration seal (PROMASTOP®-CC, 2
E120 x 50 mm) Ø 175 mm with steel pipe Ø 114 / s 3.6 mm u/c and mineral
mine wool insulation
EI90
(class A2, 40 kg/m³, melting point ≥ 1000 °C, 30 mm) in LS configurat ion with a total
centred penetration length of 1000 mm.
No. 108 Metal pipe penetration seal: Opening in the soft penetration seal (PROMASTOP®-CC, 2
E120 x 50 mm) Ø 280 mm with steel pipe Ø 220 / s 4.5 mm u/c and mineral
mine wool insulation
EI90
(class A2, 400 kg/m³, melting point ≥ 1000 °C, 30 mm) in LS configuration with a total
centred penetration length of 2500 mm.
No. 109 Metal pipe penetration seal: Opening in the soft penetration seal (PROMASTOP®-CC, 2
EI120 x 50 mm) Ø 220 mm with copper pipe Ø 18 / s 1.0 mm u/c and mineral wool insulation
ins
(class A2, 40 kg/m³, melting point ≥ 1000 °C, 100 mm) in LS configuration with a total
centred penetration length of 600 mm.
No. 110 Metal pipe penetration seal: Opening in the soft penetration seal (PROMASTOP®-CC, 2
E120 x 50 mm) Ø 245 mm with copper pipe Ø 42 / s 1.5 mm u/c and mineralmine wool insulation
EI90
(class A2, 40 kg/m³, melting point ≥ 1000 °C, 100 mm) in LS configuration with a total
centred penetration length of 800 mm.
No. 111 enetration seal: Opening in the soft penetration seal (PROMASTOP®-CC, 2
Metal pipe penetration
E120 x 50 mm) Ø 290 mm with copper pipe Ø 88.9 / s 2.0 mm u/c and mineral wool
EI90
insulation (class A2, 40 kg/m³, melting point ≥ 1000 °C, 100 mm) in LS configuration
with a total centred penetration
pen length of 2000 mm.
IBS – Institut für Brandschutztechnik und Classification Report No.: 316100407-A-en
Sicherheitsforschung Gesellschaft m. b. H. Date: 08.11.2016
A - 4020 Linz, Petzoldstrasse 45 Page 8 of 103
Akkreditierte Prüf-,, Inspektions-
Inspektions und Zertifizierungsstelle Sponsor: PRTC
No. 112 Metal pipe penetration seal: Opening in the soft penetration seal (PROMASTOP®-CC, 2
EI120 x 50 mm) Ø 215 mm with steel pipe Ø 17 / s 2.0 mm u/c and mineral
mine wool insulation
(class A2, 40 kg/m³, melting point ≥ 1000 °C, 100 mm) in LS configuration with a total
centred penetration length of 500 mm.
No. 113 Metal pipe penetration seal: Opening in the soft penetration seal (PROMASTOP®-CC, 2
EI120 x 50 mm) Ø 245 mm with steel pipe Ø 42 / s 2.5 mm u/c and mineral
mine wool insulation
(class A2, 40 kg/m³, melting point ≥ 1000 °C, 100 mm) in LS configuration with a total
centred penetration length of 500 mm.
No. 114 Metal pipe penetration seal: Opening in the soft penetration seal (PROMASTOP®-CC, 2
EI120 x 50 mm) Ø 315 mm with steel pipe Ø 114 / s 3.6 mm u/c and mineral
mine wool insulation
(class A2, 40 kg/m³, melting point ≥ 1000 °C, 100 mm) in LS configuration with a total
centred penetration length of 1000 mm.
No. 115 Metal pipe penetration seal: Opening in the soft penetration seal (PROMASTOP®-CC, 2
E120 x 50 mm) Ø 420 mm with steel pipe Ø 220 / s 4.5 mm u/c and mineral
mine wool insulation
EI90
(class A2, 40 kg/m³, melting point ≥ 1000 °C, 100 mm) in LS configuration with a total
centred penetration length of 2500 mm.
No. 200 Rectangular opening 1500 x 2800 mm with cable assignment in compliance with EN
CG1 EI120
CG2 E120 EI90
1366-3:2009
3:2009 (table A.1). Sealed with two mineral wool boards coated with
CG3 E120 EI90 PROMASTOP®-CC CC (class A1, 50 mm, 150 kg/m³, melting point ≥ 1000 °C). Coating of
CG4 EI120
CG5 E120 EI90 overlapping cable, cable bundles and cable trays with PROMASTOP®-CC, length 100
CG6 E120 EI90 mm, symmetrical to the supporting construction. No circumferential coating of the
opening of the adjacent supporting construction.
Test setup: Rigid floor construction from aerated concrete; thickness 150 mm; density ≥
Test date: 30.07.2012 450 kg/m³.
No. 16c Metal pipe penetration seal: Opening in the soft penetration seal (PROMASTOP®-CC, 1
EI90 x 80 mm) Ø 80 mm with copper pipe Ø 18 / s 1.0 mm u/c and mineral wool insulation
(class A2, 40 kg/m³, melting point ≥ 1000 °C, 30 mm) in LS configuration with a total
centred penetration length of 600 mm.
No. 17c Metal pipe penetration seal: Opening in the soft penetration seal (PROMASTOP®-CC, 1
EI90 x 80 mm) Ø 105 mm with copper pipe Ø 42 / s 1.5 mm u/c and mineral
mine wool insulation
(class A2, 40 kg/m³, melting point ≥ 1000 °C, 30 mm) in LS configuration with a total
centred penetration length of 800 mm.
No. 18c Metal pipe penetration seal: Opening in the soft penetration seal (PROMASTOP®-CC, 1
EI90 x 80 mm) Ø 150 mm with copper pipe Ø 88.9 / s 2.0 mm u/c and mineral wool
insulation (class A2, 40 kg/m³, melting point ≥ 1000 °C, 30 mm) in LS configuration with
a total centred penetration length of 2000 mm.
No. 19c Metal pipe penetration seal: Opening in the soft penetration seal (PROMASTOP®-CC, 1
EI90 x 80 mm) Ø 80 mm with steel pipe Ø 17 / s 2.0 mm u/c and mineral wool insulation
(class A2, 40 kg/m³, melting point ≥ 1000 °C, 30 mm) in LS configuration with a total
centred penetration length of 500 mm.
No. 20c Metal pipe penetration seal: Opening in the soft penetration seal (PROMASTOP®-CC, 1
EI90 x 80 mm) Ø 100 mm with steel pipe Ø 42 / s 2.5 mm u/c and mineral
mine wool insulation
(class A2, 40 kg/m³, melting point ≥ 1000 °C, 30 mm) in LS configuration with a total
centred penetration length of 500 mm.
IBS – Institut für Brandschutztechnik und Classification Report No.: 316100407-A-en
Sicherheitsforschung Gesellschaft m. b. H. Date: 08.11.2016
A - 4020 Linz, Petzoldstrasse 45 Page 9 of 103
Akkreditierte Prüf-,, Inspektions-
Inspektions und Zertifizierungsstelle Sponsor: PRTC
No. 21c Metal pipe penetration seal: Opening in the soft penetration seal (PROMASTOP®-CC, 1
EI90 x 80 mm) Ø 175 mm with steel pipe Ø 114 / s 3.6 mm u/c and mineral
mine wool insulation
(class A2, 40 kg/m³, melting point ≥ 1000 °C, 30 mm) in LS configuration with a total
centred penetration length of 1000 mm.
No. 34c Rectangular opening 650 x 3000 mm with cable assignment in compliance with EN
CG1 EI90
CG2 EI90
1366-3:2009
3:2009 (table A.1). Sealed with one mineral wool board coated with
CG3 EI90 PROMASTOP®-CC CC (class A1, 80 mm, 150 kg/m³, melting point ≥ 1000 °C). Coating of
CG4 EI90
CG5 E90 EI60 overlapping cable, cable bundles and cable trays with PROMASTOP®-CC, length 100
CG6 E90 EI60 mm, symmetrical to the supporting construction. No circumferential coating of the
opening of the adjacent supporting construction.
No. 16d Metal pipe penetration seal: Opening in the soft penetration seal (PROMASTOP®-CC, 1
EI90 x 50 mm) Ø 80 mm with copper pipe Ø 18 / s 1.0 mm u/c and mineral
mine wool insulation
(class A2, 40 kg/m³, melting point ≥ 1000 °C, 30 mm) in LS configuration with a total
centred penetration length of 600 mm.
No. 17d Metal pipe penetration seal: Opening in the soft penetration seal (PROMASTOP®-CC, 1
EI90 x 50 mm) Ø 100 mm with copper pipe Ø 42 / s 1.5 mm u/c and mineral
mine wool insulation
(class A2, 40 kg/m³, melting point ≥ 1000 °C, 30 mm) in LS configuration with a to tal
centred penetration length of 800 mm.
No. 18d Metal pipe penetration seal: Opening in the soft penetration seal (PROMASTOP®-CC, 1
EI90 x 50 mm) Ø 150 mm with copper pipe Ø 88.9 / s 2.0 mm u/c and mineral wool
insulation (class A2, 40 kg/m³, melting point
p ≥ 1000 °C, 30 mm) in LS configuration with
a total centred penetration length of 1700 mm.
No. 19d Metal pipe penetration seal: Opening in the soft penetration seal (PROMASTOP®-CC, 1
EI90 x 50 mm) Ø 80 mm with steel pipe Ø 17 / s 2.0 mm u/c and mineral wool insulation
(class A2, 40 kg/m³, melting point ≥ 1000 °C, 30 mm) in LS configuration with a total
centred penetration length of 500 mm.
No. 20d Metal pipe penetration seal: Opening in the soft penetration seal (PROMASTOP®-CC, 1
EI90 x 50 mm) Ø 105 mm with steel pipe Ø 42 / s 2.5 mm u/c and mineral
mine wool insulation
(class A2, 40 kg/m³, melting point ≥ 1000 °C, 30 mm) in LS configuration with a total
centred penetration length of 500 mm.
No. 21d Metal pipe penetration seal: Opening in the soft penetration seal (PROMASTOP®-CC, 1
EI90 x 50 mm) Ø 175 mm with steel pipe Ø 114 / s 3.6 mm u/c and mineral
mine wool insulation
(class A2, 40 kg/m³, melting point ≥ 1000 °C, 30 mm) in LS configuration with a total
centred penetration length of 1000 mm.
No. 34d
CG1 EI90
Rectangular opening 650 x 3000 mm with cable assignment in compliance with EN
CG2 E90 EI60 1366-3:2009
3:2009 (table A.1). Sealed with one mineral wool board coated with
CG3 E90 EI60
CG4 EI90 PROMASTOP®-CC CC (class A1, 50 mm, 150 kg/m³, melting point ≥ 1000 °C). Coating of
CG5 E90 EI60 overlapping cable, cable bundles and cable trays with PROMASTOP®-CC, length 100
CG6 E90 EI45
mm, symmetrical to the supporting construction. No circumferential coating of the
opening of the adjacent supporting construction.
IBS – Institut für Brandschutztechnik und Classification Report No.: 316100407-A-en
Sicherheitsforschung Gesellschaft m. b. H. Date: 08.11.2016
A - 4020 Linz, Petzoldstrasse 45 Page 10 of 103
Akkreditierte Prüf-,, Inspektions-
Inspektions und Zertifizierungsstelle Sponsor: PRTC
Test setup: Flexible wall construction; with a thickness of 100 mm; two layers of gypsum
Test date: 14.08.2012 plaster boards of 12.5 mm in acc. with EN 520; with backfilling from 40 mm
mineral wool acc. to class A1 (density 100 kg/m³).
No. 16c Metal pipe penetration seal: Opening in the soft penetration seal (PROMASTOP®-CC, 1
EI90 x 80 mm) Ø 80 mm with copper pipe Ø 18 / s 1.0 mm u/c and mineral wool insulation
(class A2, 40 kg/m³, melting point ≥ 1000 °C, 30 mm) in LS configuration with a tota l
centred penetration length of 600 mm.
No. 17c Metal pipe penetration seal: Opening in the soft penetration seal (PROMASTOP®-CC, 1
EI90 x 80 mm) Ø 105 mm with copper pipe Ø 42 / s 1.5 mm u/c and mineral wool insulation
(class A2, 40 kg/m³, melting point ≥ 1000 °C, 30 mm) in LS configuration with a total
centred penetration length of 800 mm.
No. 18c Metal pipe penetration seal: Opening in the soft penetration seal (PROMASTOP®-CC, 1
EI90 x 80 mm) Ø 145 mm with copper pipe Ø 88.9 / s 2.0 mm u/c and mineral wool
insulation (class A2, 40 kg/m³, melting point ≥ 1000 °C, 30 mm) in LS configuration with
a total centred penetration length of 2000 mm.
No. 19c Metal pipe penetration seal: Opening in the soft penetration seal (PROMASTOP®-CC, 1
EI90 x 80 mm) Ø 80 mm with steel pipe Ø 17 / s 2.0 mm u/c and mineral wool insulation
(class A2, 40 kg/m³, melting point ≥ 1000 °C, 30 mm) in LS configuration with a total
centred penetration length of 500 mm.
No. 20c oft penetration seal (PROMASTOP®-CC, 1
Metal pipe penetration seal: Opening in the soft
EI90 x 80 mm) Ø 100 mm with steel pipe Ø 42 / s 2.5 mm u/c and mineral wool insulation
(class A2, 40 kg/m³, melting point ≥ 1000 °C, 30 mm) in LS configuration with a total
centred penetration length of 500 mm.
No. 21c Metal pipe penetration seal: Opening in the soft penetration seal (PROMASTOP®-CC, 1
EI90 x 80 mm) Ø 175 mm with steel pipe Ø 114 / s 3.6 mm u/c and mineral
mine wool insulation
(class A2, 40 kg/m³, melting point ≥ 1000 °C, 30 mm) in LS configuration with a total
centred penetration length of 1000 mm.
No. 34c Rectangular opening 650 x 3000 mm with cable assignment in compliance with EN
CG1 EI90
CG2 E90 EI60
1366-3:2009
3:2009 (table A.1). Sealed with one mineral wool board coated with
CG3 E90 EI60 PROMASTOP®-CC CC (class A1, 80 mm, 150 kg/m³, melting point ≥ 1000 °C). Coating of
CG4 EI90
CG5 E90 EI60 overlapping cable, cable bundles and cable trays with PROMASTOP®-CC, length 100
CG6 E90 EI60 mm, symmetrical to the supporting construction.
Circumferential coating of the opening of adjacent supporting construction:
construction 10 mm
No. 16d Metal pipe penetration seal: Opening in the soft penetration seal (PROMASTOP®-CC, 1
EI90 x 50 mm) Ø 70 mm with copper pipe Ø 18 / s 1.0 mm u/c and mineralmine wool insulation
(class A2, 40 kg/m³, melting point ≥ 1000 °C, 30 mm) in LS configuration with a total
centred penetration length of 600 mm.
No. 17d Metal pipe penetration seal: Opening in the soft penetration seal (PROMASTOP®-CC, 1
E90 x 50 mm) Ø 105 mm with copper pipe Ø 42 / s 1.5 mm u/c and mineralmine wool insulation
EI60
(class A2, 40 kg/m³, melting point ≥ 1000 °C, 30 mm) in LS configuration with a total
centred penetration length of 800 mm.
No. 18d Metal pipe penetration seal: Opening in the soft penetration seal (PROMASTOP®-CC, 1
E90 x 50 mm) Ø 145 mm with copper pipe Ø 88.9 / s 2.0 mm u/c and mineral wool
EI60
insulation (class A2, 40 kg/m³, melting point ≥ 1000 °C, 30 mm) in LS configuration with
a total centred penetration length of 2000 mm.
IBS – Institut für Brandschutztechnik und Classification Report No.: 316100407-A-en
Sicherheitsforschung Gesellschaft m. b. H. Date: 08.11.2016
A - 4020 Linz, Petzoldstrasse 45 Page 11 of 103
Akkreditierte Prüf-,, Inspektions-
Inspektions und Zertifizierungsstelle Sponsor: PRTC
Test setup: Rigid floor construction from aerated concrete; thickness 150 mm; density ≥
Test date: 11.01.2012 450 kg/m³.
No. 51 Plastic pipe penetration: Opening in the soft penetration seal (PROMASTOP®-CC, 2 x
EI90 50 mm) Ø 160 mm with PP-HPP pipe Ø 160 / s 4.0 mm u/u. PROMASTOP®-FC3/160
(crit.)
surface-mounted
mounted on bottom side of the soft penetration seal in acc. with the installation
guideline.
No. 52 Plastic pipe penetration: Opening in the soft penetration seal (PROMASTOP®-CC, 2 x
EI90 50 mm) Ø 125 mm with Poloplast PoloKal NG Ø 125 / s 3.9 mm u/u. PROMASTOP®-
(crit.)
FC3/125 surface--mounted on bottom side of the soft penetration seal in acc. with the
installation guideline.
guideline
No. 53 (PROMAST ®-CC, 2 x
Plastic pipe penetration: Opening in the soft penetration seal (PROMASTOP
EI90 50 mm) Ø 160 mm with Poloplast PoloKal NG Ø 160 / s 4.9 mm u/u. PROMASTOP®-
(crit.)
FC3/160 surface--mounted on bottom side of the soft penetration seal in acc. with the
installation guideline.
guideline
Test setup: Flexible wall construction; with a thickness of 100 mm; two layers of gypsum
Test date: 23.01.2012 plaster boards of 12.5 mm in acc. with EN 520; with backfilling from 40 mm
mineral wool acc. to class A1 (density 100 kg/m³).
No. 51 Plastic pipe penetration: Opening in the soft penetration seal (PROMASTOP®-CC, 2 x
EI120 50 mm) Ø 160 mm with PP-HPP H pipe Ø 160 / s 4.0 mm u/u. PROMASTOP®-FC3/160
surface-mounted
mounted on both sides in acc. with the installation guidelines.
guidelines
IBS – Institut für Brandschutztechnik und Classification Report No.: 316100407-A-en
Sicherheitsforschung Gesellschaft m. b. H. Date: 08.11.2016
A - 4020 Linz, Petzoldstrasse 45 Page 12 of 103
Akkreditierte Prüf-,, Inspektions-
Inspektions und Zertifizierungsstelle Sponsor: PRTC
No. 53 Plastic pipe penetration: Opening in the soft penetration seal (PROMASTOP®-CC, 2 x
EI120 50 mm) Ø 160 mm with Poloplast PoloKal NG Ø 160 / s 4.9 mm u/u. PROMASTOP®-
FC3/160 surface--mounted on both sides in acc. with the installation guidelines.
guidelines
No. 52 Plastic pipe penetration: Opening in the soft penetration seal (PROMASTOP®-CC, 2 x
EI120 50 mm) Ø 125 mm with Poloplast PoloKal NG Ø 125 / s 3.9 mm u/u. PROMASTOP®-
FC3/125 surface--mounted on both sides in acc. with the installation guidelines.
guidelines
No. 66 Composite pipe (plastic and metal) penetration: Opening in the softso penetration seal
EI120 (PROMASTOP®-CC, -CC, 2 x 50 mm) Ø 24 mm with aluminium composite pipe (Geberit
Mepla)) Ø 16 / s 2.25 mm u/u. With insulation (class E, s 4 mm) in LS configuration with
a total centred penetration length of 200 mm. PROMASTOP®-FC3/32 surface-mounted
on both sides in acc. with the installation guidelines.
No. 67 Composite pipe (plastic and metal) penetration: Opening in the soft penetration seal
E120 (PROMASTOP®-CC, -CC, 2 x 50 mm) Ø 40 mm with aluminium composite pipe (Geberit
EI45
Mepla)) Ø 32 / s 3.0 mm u/u. With insulation (class E, s 4 mm) in LS configuration with a
total centred penetration length of 200 mm. PROMASTOP®-FC3/32 FC3/32 surface-mounted
surface
on both sides in acc. with the installation guidelines.
No. 68 Composite pipe (plastic and metal) penetration: Opening in the soft penetration seal
E120 (PROMASTOP®-CC, -CC, 2 x 50 mm) Ø 71 mm with aluminium composite pipe (Geberit
EI45
Mepla)) Ø 63 / s 4.5 mm u/u. With insulation (class
(class E, s 4 mm) in LS configuration with a
total centred penetration length of 200 mm. PROMASTOP®-FC3/63 FC3/63 surface-mounted
surface
on both sides in acc. with the installation guidelines.
No. 69 Composite pipe (plastic and metal) penetration: Opening in the soft penetration seal
E120 (PROMASTOP®-CC, -CC, 2 x 50 mm) Ø 83 mm with aluminium composite pipe (Geberit
EI45
Mepla)) Ø 75 / s 4.7 mm u/u. With insulation (class E, s 4 mm) in LS configuration with a
total centred penetration length of 200 mm. PROMASTOP®-FC3/75 surface-mounted
on both sides in acc. with the installation guidelines.
No. 85 Composite pipe (plastic and metal) penetration: Opening in the soft penetration seal
EI120 (PROMASTOP®-CC, -CC, 2 x 50 mm) Ø 28 mm with aluminium composite pipe (Geberit
Mepla)) Ø 16 /s 2.25 mm u/c. With insulation (class B-s3,d0;
s3,d0; s 6 mm) in LS configuration
with a total centred penetration length of 500 mm. PROMASTOP®-FC3/32 surface-
mounted on both sides in acc. with the installation guidelines..
No. 86 Composite pipe (plastic and metal) penetration: Opening in the soft penetration seal
EI90 (PROMASTOP®-CC, -CC, 2 x 50 mm) Ø 38 mm with aluminium composite pipe (Geberit
Mepla)) Ø 26 / s 3.0 mm u/u. With insulation (class B-s3,d0;
B s3,d0; s 6 mm) in LS configuration
with a total centred penetration length of 500 mm. PROMASTOP®-FC3/32 surface-
mounted on both sides in acc. with the installation guidelines..
No. 87 Composite pipe (plastic and metal) penetration: Opening in the soft penetration seal
E120 (PROMASTOP®-CC, -CC, 2 x 50 mm) Ø 87 mm with aluminium composite
compo pipe (Geberit
EI60
Mepla)) Ø 75 / s 4.7 mm u/u. With insulation (class B-s3,d0;
B s3,d0; s 6 mm) in LS configuration
with a total centred penetration length of 500 mm. PROMASTOP®-FC3/75 surface-
mounted on both sides in acc. with the installation guidelines..
No. 88 Composite pipe (plastic and metal) penetration: Opening in the soft penetration seal
EI90 (PROMASTOP®-CC, -CC, 2 x 50 mm) Ø 80 mm with aluminium composite pipe (Geberit
Mepla)) Ø 16 /s 2.25 mm u/c. With insulation (class B-s3,d0;
B s3,d0; s 32 mm) in LS
configuration with a total centred penetration length of 500 mm. PROMASTOP®-FC3/75
surface-mounted
mounted on both sides in acc. with the installation guidelines.
guidelines
IBS – Institut für Brandschutztechnik und Classification Report No.: 316100407-A-en
Sicherheitsforschung Gesellschaft m. b. H. Date: 08.11.2016
A - 4020 Linz, Petzoldstrasse 45 Page 13 of 103
Akkreditierte Prüf-,, Inspektions-
Inspektions und Zertifizierungsstelle Sponsor: PRTC
No. 89 Composite pipe (plastic and metal) penetration: Opening in the soft penetration seal
EI90 (PROMASTOP®-CC, -CC, 2 x 50 mm) Ø 139 mm with aluminium composite pipe (Geberit
Mepla)) Ø 75 /s 4.7 mm u/c. With insulation (class B-s3,d0;
B s3,d0; s 32 mm) in LS configuration
with a total centred penetration length of 500 mm. PROMASTOP®-FC3/140 surface-
mounted on both sides in acc.
a with the installation guidelines..
Test setup: Rigid floor construction from aerated concrete; thickness 150 mm; density ≥
450 kg/m³.
Test setup: Flexible wall construction; with a thickness of 100 mm; two layers of gypsum
plaster boards of 12.5 mm in acc. with EN 520; with no backfilling.
No. A Blank seal with 3 m² seal size. Sealed with two mineral wool boards coated with
EI120 PROMASTOP®-CC CC (class A1, 50 mm, 150 kg/m³, melting point ≥ 1000 °C). No
circumferential coating on the adjacent supporting construction.
Test setup: Flexible wall construction; with a thickness of 100 mm; two layers of gypsum
plaster boards of 12.5 mm in acc. with EN 520; with no backfilling.
No. A Blank seal with 3 m² seal size. Sealed with one mineral wool board coated with
EI120 PROMASTOP®-CC CC (class A1, 80 mm, 150 kg/m³, melting point ≥ 1000 °C). No
circumferential coating on the adjacent supporting construction.
IBS – Institut für Brandschutztechnik und Classification Report No.: 316100407-A-en
Sicherheitsforschung Gesellschaft m. b. H. Date: 08.11.2016
A - 4020 Linz, Petzoldstrasse 45 Page 14 of 103
Akkreditierte Prüf-,, Inspektions-
Inspektions und Zertifizierungsstelle Sponsor: PRTC
Test setup: Flexible wall construction; with a thickness of 100 mm; two layers of gypsum
plaster boards of 12.5 mm in acc. with EN 520; with backfilling from 40 mm
mineral wool acc. to class A1 (density 40 kg/m³).
No. B Blank seal with 3 m² seal size. Sealed with one mineral wool board coated with
E90 EI60 PROMASTOP®-CC CC (class A1, 500 mm, 150 kg/m³, melting point ≥ 1000 °C). No
circumferential coating on the adjacent supporting construction.
Test setup: Rigid floor construction from aerated concrete; thickness 150 mm; density ≥
450 kg/m³.
No. A Blank seal with 3 m² seal size. Sealed with two mineral wool boards coated with
EI120 PROMASTOP®-CC CC (class A1, 50 mm, 150 kg/m³, melting point ≥ 1000 °C). No
circumferential coating on the adjacent supporting construction.
Test setup: Rigid floor construction from aerated concrete; thickness 150 mm; density ≥
450 kg/m³.
No. A Blank seal with 3 m² seal size. Sealed with one mineral wool board coated with
EI120 PROMASTOP®-CC CC (class A1, 80 mm, 150 kg/m³, melting point ≥ 1000 °C). No
circumferential coating on the adjacent supporting construction.
Test setup: Rigid floor construction from aerated concrete; thickness 150 mm; density ≥
450 kg/m³.
No. R Blank seal with 1,74 m² seal size. Sealed with one mineral wool board coated with
EI60 PROMASTOP®-CC CC (class A1, 50
50 mm, 150 kg/m³, melting point ≥ 1000 °C). No
circumferential coating on the adjacent supporting construction.
IBS – Institut für Brandschutztechnik und Classification Report No.: 316100407-A-en
Sicherheitsforschung Gesellschaft m. b. H. Date: 08.11.2016
A - 4020 Linz, Petzoldstrasse 45 Page 15 of 103
Akkreditierte Prüf-,, Inspektions-
Inspektions und Zertifizierungsstelle Sponsor: PRTC
Test specimen 11
EN 1366-3: 2009 Fire integrity (E)
in conjunction with Time until cotton pad ignition [min.] ≥ 90
EN 1363-1: 2000 Time until failure of gap gauge ≥ 90
criteria [min.]
Pr-10-2.098 Time until occurrence of sustained ≥ 90
flaming [min.]
of 22.09.2010 Thermal insulation (I)
Test date: 04.12.2009 Time of exceeding the maximum ≥ 90
temperature increase above 180 K
CC on the unexposed side [min.]
Test specimen 31
EN 1366-4: 2006 Fire integrity (E)
in conjunction with Time until cotton pad ignition [min.] ≥ 120
EN 1363-1: 2000 Time until failure of gap gauge ≥ 120
criteria [min.]
Pr-10-2.099 Time until occurrence of sustained ≥ 120
flaming [min.]
of 22.09.2010 Thermal insulation (I)
Test date: 27.07.2010 Time of exceeding the maximum ≥ 60
temperature increase above 180 K
CC joint on the unexposed side [min.]
Test specimen 32
EN 1366-4: 2006 Fire integrity (E)
in conjunction with Time until cotton pad ignition [min.] ≥ 120
EN 1363-1: 2000 Time until failure of gap gauge ≥ 120
criteria [min.]
Pr-10-2.099 Time until occurrence of sustained ≥ 120
flaming [min.]
of 22.09.2010 Thermal insulation (I)
Test date: 27.07.2010 Time of exceeding the maximum ≥ 120
temperature increase above 180 K
CC joint on the unexposed side [min.]
IBS – Institut für Brandschutztechnik und Classification Report No.: 316100407-A-en
Sicherheitsforschung Gesellschaft m. b. H. Date: 08.11.2016
A - 4020 Linz, Petzoldstrasse 45 Page 20 of 103
Akkreditierte Prüf-,, Inspektions-
Inspektions und Zertifizierungsstelle Sponsor: PRTC
Test specimen 31
EN 1366-4: 2006 Fire integrity (E)
in conjunction with Time until cotton pad ignition [min.] ≥ 90
EN 1363-1: 2000 Time until failure of gap gauge ≥ 90
criteria [min.]
Pr-10-2.099 Time until occurrence of sustained ≥ 90
flaming [min.]
of 22.09.2010 Thermal insulation (I)
Test date: 29.07.2010 Time of exceeding the maximum ≥ 90
temperature increase above 180 K
CC joint on the unexposed side [min.]
Test specimen 32
EN 1366-4: 2006 Fire integrity (E)
in conjunction with Time until cotton pad ignition [min.] ≥ 90
EN 1363-1: 2000 Time until failure of gap gauge ≥ 90
criteria [min.]
Pr-10-2.099 Time until occurrence of sustained ≥ 90
flaming [min.]
of 22.09.2010 Thermal insulation (I)
Test date: 29.07.2010 Time of exceeding the maximum ≥ 90
temperature increase above 180 K
CC joint on the unexposed side [min.]
Test specimen 102, 103, 104, 105, 106, 107, 108, 109, 110,
111, 112, 113, 114, 115, 146, 149, 150, 154, 155
EN 1366-3: 2009 Pipe end configuration u/c
in conjunction with Fire integrity (E)
EN 1363-1: 2000 Time until cotton pad ignition [min.] ≥ 90
Time until failure of gap gauge ≥ 90
Pr-12-2.101 criteria [min.]
Time until occurrence of sustained ≥ 90
of 06.09.2012 flaming [min.]
Test date: 11.01.2012 Thermal insulation (I)
Time of exceeding the maximum ≥ 90
CC temperature increase above 180 K
on the unexposed side [min.]
IBS – Institut für Brandschutztechnik und Classification Report No.: 316100407-A-en
Sicherheitsforschung Gesellschaft m. b. H. Date: 08.11.2016
A - 4020 Linz, Petzoldstrasse 45 Page 21 of 103
Akkreditierte Prüf-,, Inspektions-
Inspektions und Zertifizierungsstelle Sponsor: PRTC
Test specimen 66
Pipe end configuration u/c
EN 1366-3: 2009 Fire integrity (E)
in conjunction with Time until cotton pad ignition [min.] ≥ 120
EN 1363-1: 2000 Time until failure of gap gauge ≥ 120
criteria [min.]
Pr-12-2.059 Time until occurrence of sustained ≥ 120
flaming [min.]
of 02.07.2012 Thermal insulation (I)
Test date: 23.01.2012
Time of exceeding the maximum ≥ 120
CC temperature increase above 180 K
on the unexposed side [min.]
Test specimen 85
EN 1366-3: 2009 Pipe end configuration u/c
in conjunction with Fire integrity (E)
EN 1363-1: 2000 Time until cotton pad ignition [min.] ≥ 120
Time until failure of gap gauge ≥ 120
Pr-12-2.059 criteria [min.]
Time until occurrence of sustained ≥ 120
of 02.07.2012 flaming [min.]
Test date: 23.01.2012 Thermal insulation (I)
Time of exceeding the maximum ≥ 120
CC temperature increase above 180 K
on the unexposed side [min.]
Test specimen 86
Pipe end configuration u/c
EN 1366-3: 2009 Fire integrity (E)
in conjunction with Time until cotton pad ignition [min.] ≥ 90
EN 1363-1: 2000 Time until failure of gap gauge ≥ 90
criteria [min.]
Pr-12-2.059 Time until occurrence of sustained ≥ 90
flaming [min.]
of 02.07.2012 Thermal insulation (I)
Test date: 23.01.2012
Time of exceeding the maximum ≥ 90
CC temperature increase above 180 K
on the unexposed side [min.]
Test specimen 87
Pipe end configuration u/c
EN 1366-3: 2009 Fire integrity (E)
in conjunction with Time until cotton pad ignition [min.] ≥ 120
EN 1363-1: 2000 Time until failure of gap gauge ≥ 120
criteria [min.]
Pr-12-2.059 Time until occurrence of sustained ≥ 120
flaming [min.]
of 02.07.2012 Thermal insulation (I)
Test date: 23.01.2012
Time of exceeding the maximum ≥ 60
CC temperature increase above 180 K
on the unexposed side [min.]
IBS – Institut für Brandschutztechnik und Classification Report No.: 316100407-A-en
Sicherheitsforschung Gesellschaft m. b. H. Date: 08.11.2016
A - 4020 Linz, Petzoldstrasse 45 Page 32 of 103
Akkreditierte Prüf-,, Inspektions-
Inspektions und Zertifizierungsstelle Sponsor: PRTC
Test specimen A
EN 1366-3: 2009 Fire integrity (E)
in conjunction with Time until cotton pad ignition [min.] ≥ 120
EN 1363-1: 2012 Time until failure of gap gauge ≥ 120
criteria [min.]
Pr-13-2.045 Time until occurrence of sustained ≥ 120
flaming [min.]
of 05.09.2014 Thermal insulation (I)
Time of exceeding the maximum ≥ 120
CC temperature increase above 180 K
on the unexposed side [min.]
Test specimen A
EN 1366-3: 2009 Fire integrity (E)
in conjunction with Time until cotton pad ignition [min.] ≥ 120
EN 1363-1: 2012 Time until failure of gap gauge ≥ 120
criteria [min.]
Pr-13-2.047 Time until occurrence of sustained ≥ 120
flaming [min.]
of 08.09.2014 Thermal insulation (I)
Time of exceeding the maximum ≥ 120
CC temperature increase above 180 K
on the unexposed side [min.]
Test specimen B
EN 1366-3: 2009 Fire integrity (E)
in conjunction with Time until cotton pad ignition [min.] ≥ 90
EN 1363-1: 2012 Time until failure of gap gauge ≥ 90
criteria [min.]
Pr-13-2.052 Time until occurrence of sustained ≥ 90
flaming [min.]
of 15.07.2014 Thermal insulation (I)
Time of exceeding the maximum ≥ 60
CC temperature increase above 180 K
on the unexposed side [min.]
IBS – Institut für Brandschutztechnik und Classification Report No.: 316100407-A-en
Sicherheitsforschung Gesellschaft m. b. H. Date: 08.11.2016
A - 4020 Linz, Petzoldstrasse 45 Page 34 of 103
Akkreditierte Prüf-,, Inspektions-
Inspektions und Zertifizierungsstelle Sponsor: PRTC
Test specimen A
EN 1366-3: 2009 Fire integrity (E)
in conjunction with Time until cotton pad ignition [min.] ≥ 120
EN 1363-1: 2012 Time until failure of gap gauge ≥ 120
criteria [min.]
Pr-13-2.051 Time until occurrence of sustained ≥ 120
flaming [min.]
of 15.07.2014 Thermal insulation (I)
Time of exceeding the maximum ≥ 120
CC temperature increase above 180 K
on the unexposed side [min.]
Test specimen A
EN 1366-3: 2009 Fire integrity (E)
in conjunction with Time until cotton pad ignition [min.] ≥ 120
EN 1363-1: 2012 Time until failure of gap gauge ≥ 120
criteria [min.]
Pr-13-2.093 Time until occurrence of sustained ≥ 120
flaming [min.]
of 09.04.2014 Thermal insulation (I)
Time of exceeding the maximum ≥ 120
CC temperature increase above 180 K
on the unexposed side [min.]
Test specimen R
EN 1366-3: 2009 Fire integrity (E)
in conjunction with Time until cotton pad ignition [min.] ≥ 60
EN 1363-1: 2012 Time until failure of gap gauge ≥ 60
criteria [min.]
Pr-16-2.061 Time until occurrence of sustained ≥ 60
flaming [min.]
of 10.06.2016 Thermal insulation (I)
Time of exceeding the maximum ≥ 60
CC temperature increase above 180 K
on the unexposed side [min.]
This classification has been carried out in accordance with clause 7 of EN 13501-2:2007
and A1:2009.
IBS – Institut für Brandschutztechnik und Classification Report No.: 316100407-A-en
Sicherheitsforschung Gesellschaft m. b. H. Date: 08.11.2016
A - 4020 Linz, Petzoldstrasse 45 Page 35 of 103
Akkreditierte Prüf-,, Inspektions-
Inspektions und Zertifizierungsstelle Sponsor: PRTC
4.2 Classification
R E I W t t - M S C IncSlow sn ef r
- E I - 60 - - - - - - - - -
R E I W t t - M S C IncSlow sn ef r
- E I - 60 - - - - - - - - -
R E I W t t - M S C IncSlow sn ef r
- E I - 60 - - - - - - - - -
Pr-12-2.101 – Test specimen 102, 103, 104, 105, 106, 107, 108, 109, 110, 111, 112,
113, 114, 115, 146, 149, 150, 154, 155 of 11.01.2012 CC
R E I W t t - M S C IncSlow sn ef r
- E I - 90 - - - - - - - - -
Pr-12-2.101 – Test specimen 200 CG1, CG2, CG3, CG4, CG5, CG6 of 11.01.2012 CC
R E I W t t - M S C IncSlow sn ef r
- E I - 90 - - - - - - - - -
R E I W t t - M S C IncSlow sn ef r
- E I - 90 - - - - - - - - -
R E I W t t - M S C IncSlow sn ef r
- E I - 90 - - - - - - - - -
R E I W t t - M S C IncSlow sn ef r
- E I - 90 - - - - - - - - -
R E I W t t - M S C IncSlow sn ef r
- E I - 90 - - - - - - - - -
R E I W t t - M S C IncSlow sn ef r
- E I - 90 - - - - - - - - -
Pr-12-2.101 – Test specimen 16c, 17c, 18c, 19c, 20c, 21c of 30.07.2012 CC
R E I W t t - M S C IncSlow sn ef r
- E I - 90 - - - - - - - - -
R E I W t t - M S C IncSlow sn ef r
- E I - 60 - - - - - - - - -
R E I W t t - M S C IncSlow sn ef r
- E I - 60 - - - - - - - - -
R E I W t t - M S C IncSlow sn ef r
- E I - 45 - - - - - - - - -
Pr-12-2.101 – Test specimen 16c, 17c, 18c, 19c, 20c, 21c of 30.07.2012 CC
R E I W t t - M S C IncSlow sn ef r
- E I - 90 - - - - - - - - -
R E I W t t - M S C IncSlow sn ef r
- E I - 60 - - - - - - - - -
R E I W t t - M S C IncSlow sn ef r
- E I - 60 - - - - - - - - -
R E I W t t - M S C IncSlow sn ef r
- E I - 60 - - - - - - - - -
R E I W t t - M S C IncSlow sn ef r
- E I - 45 - - - - - - - - -
R E I W t t - M S C IncSlow sn ef r
- E I - 45 - - - - - - - - -
R E I W t t - M S C IncSlow sn ef r
- E I - 60 - - - - - - - - -
R E I W t t - M S C IncSlow sn ef r
- E I - 90 - - - - - - - - -
R E I W t t - M S C IncSlow sn ef r
- E I - 60 - - - - - - - - -
The test results are only applicable to the orientation in which the penetration seals were
tested, i.e. in a wall or floor.
Pipe end configuration tests performed u/u shall also cover the configurations u/u, c/u, u/c
and c/c.
Pipe end configuration tests performed u/c shall also cover the configuration u/c and c/c.
The classification results from flexible wall constructionss may also apply to rigid wall
constructions in case the thickness and density is higher than those of the tested
construction.
4.3.4 PROMASTOP®-CC
CC soft
s penetration seals
When installing soft penetration seals, the following parameters must be observed:
The boards
oards must be of non-combustible
non combustible mineral wool (A1 in acc. with EN 13501-1)
13501 with a
melting point of ≥ 1000°C and a density of ≥ 140 kg/m³, ³, unless otherwise defined.
The distance between the mineral wool boards must be ≥ 0 mm.
The necessary thickness and number of mineral wool boards is relatedrel to the specific use
and the required classification (see table with penetration seal sizes below).
It is not necessary to use an additional framing with boards in the opening in the flexible wall
construction, the soft penetration seal can be directly mount into the metal studs.
Shortcut Description
Figure 1 – 3:
A… Flexible wall
B… PROMASTOP®-CC firestop coating
tA ≥ 100 mm
tB ≥ 0,7 mm PROMASTOP®-CC
wF depends on the soft penetration seal sizes, see
above.
F… see clause 4.3.4
Figure 1:
Figure 3:
Figure 4 – 5:
Figure 4 Figure 5
Figure 6 – 8:
Figure 9 – 11:
A… Rigid wall
B… PROMASTOP®-CC firestop coating
tA ≥ 100 mm
tB ≥ 0,7 mm PROMASTOP®-CC
wF depends on the soft penetration seal sizes, see
above.
F… see clause 4.3.4
Figure 9:
Figure 10:
Figure 11:
Figure 12 Figure 13
Figure 14 – 16:
Figure 15:
Figure 15
Figure 16:
Figure 16
IBS – Institut für Brandschutztechnik und Classification Report No.: 316100407-A-en
Sicherheitsforschung Gesellschaft m. b. H. Date: 08.11.2016
A - 4020 Linz, Petzoldstrasse 45 Page 55 of 103
Akkreditierte Prüf-,, Inspektions-
Inspektions und Zertifizierungsstelle Sponsor: PRTC
PROMASTOP®-CC CC penetration seals can be overpainted with coatings and paints based on
emulsion, polyurethane, acrylic or their mixtures for decorative or environmental protection purposes
(Test Report No. Pr-13-2.103--En, issued 09.09.2014).
PROMASTOP®-CC
CC penetration seals can be overpainted with fire stop coatings PROMASTOP®-I or
®
PROMASTOP -E (Test
st Report No. Pr-14-2.074-En,
Pr issued 25.09.2014).
There was now negative influce for the fire resistance regarding Integrity (E) and Insulation (I)
recorded.
Depending on the soft penetration seal version, the following classifications can be assigned:
Soft penetration seal versions and
orientation
Electrical installation
1 x 50 mm 1 x 80 mm 2 x 50 mm
Wall Floor Wall Floor Wall Floor
All sheated cable types
E90
Ø ≤ 21 mm EI90 EI90 EI90 EI120 EI120
EI60
(CG 1)
All sheated cable types
E90 E90 E90 E120 E120
Ø ≤ 50 mm EI60 EI60 EI60
EI90
EI90 EI90
(CG 2)
All sheated cable types
E90 E90 E90 E120 E120
Ø ≤ 80 mm EI90
EI60 EI60 EI60 EI90 EI90
(CG 3)
Cable bundle
E90
Ø ≤ 100 mm EI90 EI90 EI90 EI120 EI120
EI60
(CG 4)
Non-sheated cable types
E90 E90 E90 E90 E120
Ø ≤ 24 mm EI45 EI60 EI60
EI90
EI60 EI90
(CG 5)
Empty conduits from steel, copper or
plastic; Pipe end configuration U/C E90 E90 E90 E90 E120
EI90
Ø ≤ 16 mm EI45 EI45 EI60 EI60 EI90
(CG 6)
CG...Cable group compliant to EN 1366-3:2009
1366
Cable trays and cable ladders can be lead through the soft penetration seal.
IBS – Institut für Brandschutztechnik und Classification Report No.: 316100407-A-en
Sicherheitsforschung Gesellschaft m. b. H. Date: 08.11.2016
A - 4020 Linz, Petzoldstrasse 45 Page 56 of 103
Akkreditierte Prüf-,, Inspektions-
Inspektions und Zertifizierungsstelle Sponsor: PRTC
Figure 17 – 18:
Possible arrangement of
the single or double board
soft penetration seals in
flexible and rigid walls
Thickness of B on cable
group 6 ≥ 3 mm, see
above.
Figure 19:
Detail:
Detail If there is a space between the boards,
it is not necessary to apply the firestop
coating on the cables, cable tray... .
Figure 19
Cable trays can penetrate also the
seal.
IBS – Institut für Brandschutztechnik und Classification Report No.: 316100407-A-en
Sicherheitsforschung Gesellschaft m. b. H. Date: 08.11.2016
A - 4020 Linz, Petzoldstrasse 45 Page 57 of 103
Akkreditierte Prüf-,, Inspektions-
Inspektions und Zertifizierungsstelle Sponsor: PRTC
Figure 20 – 23:
Figure 21:
Figure 21
IBS – Institut für Brandschutztechnik und Classification Report No.: 316100407-A-en
Sicherheitsforschung Gesellschaft m. b. H. Date: 08.11.2016
A - 4020 Linz, Petzoldstrasse 45 Page 58 of 103
Akkreditierte Prüf-,, Inspektions-
Inspektions und Zertifizierungsstelle Sponsor: PRTC
Figure 22:
Figure 22
Figure 23:
Figure 23
IBS – Institut für Brandschutztechnik und Classification Report No.: 316100407-A-en
Sicherheitsforschung Gesellschaft m. b. H. Date: 08.11.2016
A - 4020 Linz, Petzoldstrasse 45 Page 59 of 103
Akkreditierte Prüf-,, Inspektions-
Inspektions und Zertifizierungsstelle Sponsor: PRTC
4.3.7 Non-combustible
combustible pipe materials with non-combustible
combustible section insulation of
class A2 / A2L or higher-graded
higher
The insulation shall be placed in the center of the supporting construction or soft penetration
seal and fixed
ed with steel wire or the like.
Results of copper pipes can be also apply to steel pipes but not vice versa.
IBS – Institut für Brandschutztechnik und Classification Report No.: 316100407-A-en
Sicherheitsforschung Gesellschaft m. b. H. Date: 08.11.2016
A - 4020 Linz, Petzoldstrasse 45 Page 60 of 103
Akkreditierte Prüf-,, Inspektions-
Inspektions und Zertifizierungsstelle Sponsor: PRTC
Supporting distances:
The installations must be suspended ≤ 250 mm on both sides from walls or on the top of
floor constructions.
The results from copper pipelines the results can be also applied to steel pipes, however,
not vice versa, and to pipes with λ ≤ 380 W/mK and a melting point of ≥ 1083 °C.
IBS – Institut für Brandschutztechnik und Classification Report No.: 316100407-A-en
Sicherheitsforschung Gesellschaft m. b. H. Date: 08.11.2016
A - 4020 Linz, Petzoldstrasse 45 Page 62 of 103
Akkreditierte Prüf-,, Inspektions-
Inspektions und Zertifizierungsstelle Sponsor: PRTC
Aluminium composite pipes (type Geberit Mepla)) with combustible insulation (maximum
thickness 4 mm, class E in acc. with EN 13501-1
13501 or higher-graded
graded (exclusive of class B),
B)
®
e.g. from PE), can be sealed with fire stop collars of type PROMASTOP -FC. The
combustible insulation is placed in the middle-position
position of the soft penetration seal and must
have a minimum length of 200 mm. When used use in walls, fire stop collars must be mounted
on both sides of the soft penetration (with threaded rods through the soft penetration). The
configuration of this insulation is effected as LS (see illustration clause 4.3.7).
Classification
Aluminium composite ®
PROMASTOP -CC
pipes with combustible 2 x 50 mm
insulation and
PROMASTOP -FC
® Wall Floor
Geberit Mepla EI 120-u/c -
Ø 16 mm
Geberit Mepla EI 45-u/c
Ø 20, 26, 32, 40, 50, 63, 75 -
mm E 120-u/c
Aluminium composite pipes (type Pipelife Radopress) with combustible insulation (thickness
4 – 9 mm, class E in acc. with EN 13501-1
13501 or higher-graded
graded (exclusive of class B), e.g. from
PE), can be sealed with fire stop wrap PROMASTOP®-W (for wall application on both sides
of the penetration seal, for floor applications on the bottom side of the penetration seal).
seal) The
combustible insulation situation is CS (see illustration clause 4.3.7).
4.3.7 .
Classification
Aluminium composite ®
PROMASTOP -CC
pipes with combustible 2 x 50 mm
insulation and
®
PROMASTOP -W – 1 Wall Floor
Layer
Pipelife Radopress EI 120-u/c EI 120-u/c
Ø 16 – 63 mm
IBS – Institut für Brandschutztechnik und Classification Report No.: 316100407-A-en
Sicherheitsforschung Gesellschaft m. b. H. Date: 08.11.2016
A - 4020 Linz, Petzoldstrasse 45 Page 63 of 103
Akkreditierte Prüf-,, Inspektions-
Inspektions und Zertifizierungsstelle Sponsor: PRTC
Aluminium composite pipes (type Geberit Mepla)) with combustible insulation (thickness
from ≥ 6 mm to ≤ 32 mm, class B-s3,
B d0 in acc. with EN 13501-1 or higher-graded,
higher e.g. from
®
elastomeric foam), can be sealed with fire stop collars of type PROMASTOP -FC.
Aluminium composite ®
PROMASTOP -CC
pipes with combustible 2 x 50 mm
insulation and
PROMASTOP -FC
® Wall Floor
Geberit Mepla EI 120-u/c -
Ø 16 mm
Geberit Mepla EI 90-u/c -
Ø 20, 26 mm
Geberit Mepla EI 60-u/c
Ø 32, 40, 50, 63, 75 mm -
E 120-u/c
Aluminium composite ®
PROMASTOP -CC
pipes with combustible 2 x 50 mm
insulation and
PROMASTOP -FC
® Wall Floor
Geberit Mepla
Ø 16, 20, 26, 32, 40, 50, 63, EI 90-u/c -
75 mm
Aluminium composite pipes (type Pipelife Radopress) with combustible insulation (thickness
6 – 32 mm, class B-s3,
s3, d0 in acc. with EN 13501-1
13501 or higher-graded,
graded, e.g. from elastomeric
®
foam), can be sealed with fire stop wrap PROMASTOP -W (for for wall application on both
IBS – Institut für Brandschutztechnik und Classification Report No.: 316100407-A-en
Sicherheitsforschung Gesellschaft m. b. H. Date: 08.11.2016
A - 4020 Linz, Petzoldstrasse 45 Page 64 of 103
Akkreditierte Prüf-,, Inspektions-
Inspektions und Zertifizierungsstelle Sponsor: PRTC
sides
ides of the penetration seal, for floor applications on the bottom side of the penetration
seal).. The combustible insulation is placed in the middle-position
middle position of the soft penetration seal
and must have a minimum length of 500 mm, the insulation situation is LS (see illustration
clause 4.3.7).
Classification
Aluminium composite ®
PROMASTOP -CC
pipes with combustible 2 x 50 mm
insulation and
®
PROMASTOP -W – 1 Wall Floor
Layer
Pipelife Radopress EI 120-u/c
u/c
Ø 16 – 63 mm EI 120-u/c
* for Ø 63 mm E120 EI60-u/c*
u/c*
IBS – Institut für Brandschutztechnik und Classification Report No.: 316100407-A-en
Sicherheitsforschung Gesellschaft m. b. H. Date: 08.11.2016
A - 4020 Linz, Petzoldstrasse 45 Page 65 of 103
Akkreditierte Prüf-,, Inspektions-
Inspektions und Zertifizierungsstelle Sponsor: PRTC
The fire stop wrap PROMASTOP®-W shall be e wrapped around plastic pipes within the
PROMASTOP®-CC CC penetration seal. For wall application on both sides of the penetration
seal, for floor applications on the bottom side of the penetration seal. PROMASTOP®-W
shall be installed flushed to the surface of the penetration seal (max. 5 mm off the surface)
and shall be fixed with PROMASTOP®-CC, PROMASEAL®-A A or PROMASEAL®-AG.
The classification results from flexible wall constructions may also apply to rigid wall
constructions in case the thickness and density is equal or higher than those of the tested
construction.
When used in walls, the fire stop collars must be installed on both sides of the wall; but
when used in floor constructions the fire stop collars are only needed on the bottom side.
Sockets:
The diameter of the socketss may be reduced but not increased.
re the usage of PROMASTOP®-FC6 fire stop collars.
Sockets always require
Sound decoupling:
Any sound decoupling strips based on PE foam and class E (acc. to EN 13501-1)
13501 or higher-
graded with a maximum thickness of 5 mm can be used.
IBS – Institut für Brandschutztechnik und Classification Report No.: 316100407-A-en
Sicherheitsforschung Gesellschaft m. b. H. Date: 08.11.2016
A - 4020 Linz, Petzoldstrasse 45 Page 69 of 103
Akkreditierte Prüf-,, Inspektions-
Inspektions und Zertifizierungsstelle Sponsor: PRTC
Supporting distance:
The installations must be suspended ≤ 250 mm on both sides from walls or on the top of
floor constructions.
When taking the results of the critical pipe method into account the following pipes and
installation types shall apply:
Soft
Dimension range penetra
Orientation
Designation Ø…Diameter F...Floor Collar type Classification
s…
…pipe wall thickness
tion W...wall
(mm)
Friatec Friaphon Ø 52 / s 2.8 - Ø 110 / s 5.3 1 x 50 F FC3 EI60-U/U
Friatec Friaphon Ø 52 / s 2.8 - Ø 110 / s 5.3 1 x 80 F FC3 EI90-U/U
Friatec Friaphon Ø 52 / s 2.8 - Ø 110 / s 5.3 2 x 50 F FC3 EI90-U/U
Friatec dBlue Ø 50 / s 1.8 - Ø 125 / s 3.9 1 x 50 F FC3 EI60-U/U
Friatec dBlue Ø 50 / s 1.8 - Ø 125 / s 3.9 1 x 80 F FC3 EI90-U/U
Friatec dBlue Ø 50 / s 1.8 - Ø 125 / s 3.9 2 x 50 F FC3 EI90-U/U
IBS – Institut für Brandschutztechnik und Classification Report No.: 316100407-A-en
Sicherheitsforschung Gesellschaft m. b. H. Date: 08.11.2016
A - 4020 Linz, Petzoldstrasse 45 Page 71 of 103
Akkreditierte Prüf-,, Inspektions-
Inspektions und Zertifizierungsstelle Sponsor: PRTC
Details on the dimensions of combustible pipes can be taken from the following diagrams.
Friatec Friaphon pipe with or without sound decoupling combined with surface-mounted
surface
firestop collar PROMASTOP®-FC FC on soft penetration seal PROMASTOP®-CC with EI60 –
u/u:
IBS – Institut für Brandschutztechnik und Classification Report No.: 316100407-A-en
Sicherheitsforschung Gesellschaft m. b. H. Date: 08.11.2016
A - 4020 Linz, Petzoldstrasse 45 Page 73 of 103
Akkreditierte Prüf-,, Inspektions-
Inspektions und Zertifizierungsstelle Sponsor: PRTC
Friatec Friaphon pipe with or without sound decoupling combined with surface-mounted
surface
®
firestop collar PROMASTOP -FC FC on soft penetration seal PROMASTOP®-CC with EI90 –
u/u:
Friatec Friaphon pipe with or without sound decoupling combined with surface-mounted
surface
firestop collar PROMASTOP®-FC FC on soft penetration seal PROMASTOP®-CC with EI90 –
u/u:
IBS – Institut für Brandschutztechnik und Classification Report No.: 316100407-A-en
Sicherheitsforschung Gesellschaft m. b. H. Date: 08.11.2016
A - 4020 Linz, Petzoldstrasse 45 Page 74 of 103
Akkreditierte Prüf-,, Inspektions-
Inspektions und Zertifizierungsstelle Sponsor: PRTC
Friatec dBlue pipe with or without sound decoupling combined with surface-mounted
surface
firestop collar PROMASTOP®-FC FC on soft penetration seal PROMASTOP®-CC with EI60 –
u/u:
Friatec dBlue pipe with or without sound decoupling combined with surface-mounted
surface
®
firestop collar PROMASTOP -FC FC on soft penetration seal PROMASTOP®-CC with EI90 –
u/u:
IBS – Institut für Brandschutztechnik und Classification Report No.: 316100407-A-en
Sicherheitsforschung Gesellschaft m. b. H. Date: 08.11.2016
A - 4020 Linz, Petzoldstrasse 45 Page 75 of 103
Akkreditierte Prüf-,, Inspektions-
Inspektions und Zertifizierungsstelle Sponsor: PRTC
Friatec dBlue pipe with or without sound decoupling combined with surface-mounted
surface
®
firestop collar PROMASTOP -FC FC on soft penetration seal PROMASTOP®-CC with EI90 –
u/u:
Rehau Raupiano Plus pipe with socket and with/without sound decoupling combined with
surface-mounted firestop collar PROMASTOP®-FCFC on soft penetration seal PROMASTOP®-
CC with EI60 – u/u:
IBS – Institut für Brandschutztechnik und Classification Report No.: 316100407-A-en
Sicherheitsforschung Gesellschaft m. b. H. Date: 08.11.2016
A - 4020 Linz, Petzoldstrasse 45 Page 76 of 103
Akkreditierte Prüf-,, Inspektions-
Inspektions und Zertifizierungsstelle Sponsor: PRTC
Rehau Raupiano Plus pipe with socket and with/without sound decoupling combined with
surface-mounted firestop collar PROMASTOP®-FCFC on soft penetration seal PROMASTOP®-
CC with EI90 – u/u:
Rehau Raupiano Plus pipe with socket and with/without sound decoupling combined with
surface-mounted firestop collar PROMASTOP®-FCFC on soft penetration seal PROMASTOP®-
CC with EI90 – u/u:
IBS – Institut für Brandschutztechnik und Classification Report No.: 316100407-A-en
Sicherheitsforschung Gesellschaft m. b. H. Date: 08.11.2016
A - 4020 Linz, Petzoldstrasse 45 Page 77 of 103
Akkreditierte Prüf-,, Inspektions-
Inspektions und Zertifizierungsstelle Sponsor: PRTC
Rehau Raupiano Plus pipe with or without sound decoupling combined with surface-
surface
mounted firestop collar PROMASTOP -FC on soft penetration seal PROMASTOP®-CC with
®
EI60 – u/u:
Rehau Raupiano Plus pipe with or without sound decoupling combined with surface-
surface
®
mounted firestop collar PROMASTOP -FC FC on soft penetration seal PROMASTOP®-CC with
EI90 – u/u:
IBS – Institut für Brandschutztechnik und Classification Report No.: 316100407-A-en
Sicherheitsforschung Gesellschaft m. b. H. Date: 08.11.2016
A - 4020 Linz, Petzoldstrasse 45 Page 78 of 103
Akkreditierte Prüf-,, Inspektions-
Inspektions und Zertifizierungsstelle Sponsor: PRTC
Rehau Raupiano Plus pipe ipe with or without sound decoupling combined with surface-
surface
®
mounted fire stop collar PROMASTOP -FC FC on soft penetration seal PROMASTOP®-CC
with EI90 – u/u:
The test results of the PE pipes shall also apply to ABS pipes in accordance with EN 1455-1
1455
and SAN and PVC pipes complying with EN 1565-1.
1565
PE-HD
HD pipe conforming with EN 12201-2,
12201 EN 1519-1, EN 12666-1,
1, DIN 8074 and DIN 8075
mounted firestop collar PROMASTOP®-FC
with surface-mounted FC on soft penetration seal
PROMASTOP®-CC with EI90 – u/u:
IBS – Institut für Brandschutztechnik und Classification Report No.: 316100407-A-en
Sicherheitsforschung Gesellschaft m. b. H. Date: 08.11.2016
A - 4020 Linz, Petzoldstrasse 45 Page 87 of 103
Akkreditierte Prüf-,, Inspektions-
Inspektions und Zertifizierungsstelle Sponsor: PRTC
The test results of the PE pipes shall also apply to ABS pipes in accordance with EN 1455-1
1455
and SAN and PVC pipes complying with EN 1565-1.
1565
PE-HD
HD pipe conforming with EN 12201-2,
12201 EN 1519-1, EN 12666-1,
1, DIN 8074 and DIN 8075
ounted firestop collar PROMASTOP®-FC
with surface-mounted FC on soft penetration seal
PROMASTOP®-CC CC with EI90 – u/u:
The test results of the PE pipes shall also apply to ABS pipes in accordance with EN 1455-1
1455
and SAN and PVC pipes complying with EN 1565-1.
1565
Rehau Raupiano Plus pipe with socket and with/without sound decoupling combined
com with
surface-mounted firestop collar PROMASTOP®-FC penetrati seal PROMASTOP®-
FC on soft penetration
CC with EI60 – u/u:
Rehau Raupiano Plus pipe with socket and with/without sound decoupling combined
com with
surface-mounted firestop collar PROMASTOP®-FC
FC on soft penetration seal PROMASTOP®-
CC with EI90 – u/u:
IBS – Institut für Brandschutztechnik und Classification Report No.: 316100407-A-en
Sicherheitsforschung Gesellschaft m. b. H. Date: 08.11.2016
A - 4020 Linz, Petzoldstrasse 45 Page 90 of 103
Akkreditierte Prüf-,, Inspektions-
Inspektions und Zertifizierungsstelle Sponsor: PRTC
Rehau Raupiano Plus pipe with socket and with/without sound decoupling combined with
surface-mounted firestop collar PROMASTOP®-FC
FC on soft penetration seal PROMASTOP®-
CC with EI120 – u/u:
PE-HD pipe conforming with EN 12201-2, EN 1519-1, EN 12666-1, 1, DIN 8074 and DIN 8075
with the built in firestop collar PROMASTOP®-FC
FC on soft penetration seal PROMASTOP®-
CC with EI120 – u/u:
The test results of the PE pipes shall also apply to ABS pipes in accordance with EN 1455-1
and SAN and PVC pipes complying with EN 1565-1.
1565
PE-HD
HD pipe conforming with EN 12201-2,
12201 EN 1519-1, EN 12666-1,
1, DIN 8074 and DIN 8075
mounted firestop collar PROMASTOP®-FC
with surface-mounted FC on soft penetration seal
PROMASTOP®-CC CC with EI60 – u/u:
est results of the PE pipes shall also apply to ABS pipes in accordance with EN 1455-1
The test 1455
and SAN and PVC pipes complying with EN 1565-1.
1565
IBS – Institut für Brandschutztechnik und Classification Report No.: 316100407-A-en
Sicherheitsforschung Gesellschaft m. b. H. Date: 08.11.2016
A - 4020 Linz, Petzoldstrasse 45 Page 98 of 103
Akkreditierte Prüf-,, Inspektions-
Inspektions und Zertifizierungsstelle Sponsor: PRTC
PE-HD
HD pipe conforming with EN 12201-2,
12201 EN 1519-1, EN 12666-1,
1, DIN 8074 and DIN 8075
mounted firestop collar PROMASTOP®-FC
with surface-mounted FC on soft penetration seal
PROMASTOP®-CC CC with EI90 – u/u:
The test results of the PE pipes shall also apply to ABS pipes in accordance with EN 1455-1
1455
and SAN and PVC pipes complying with EN 1565-1.
1565
PE-HD
HD pipe conforming with EN 12201-2,
122 EN 1519-1, EN 12666-1,
1, DIN 8074 and DIN 8075
mounted firestop collar PROMASTOP®-FC
with surface-mounted FC on soft penetration seal
PROMASTOP®-CC CC with EI90 – u/u:
The test results of the PE pipes shall also apply to ABS pipes in accordance with EN 1455-1
1455
and SAN and PVC pipes complying with EN 1565-1.
1565
IBS – Institut für Brandschutztechnik und Classification Report No.: 316100407-A-en
Sicherheitsforschung Gesellschaft m. b. H. Date: 08.11.2016
A - 4020 Linz, Petzoldstrasse 45 Page 99 of 103
Akkreditierte Prüf-,, Inspektions-
Inspektions und Zertifizierungsstelle Sponsor: PRTC
PP-H and PP-R pipes (e.g. complying with OENORM B 5174-1, 1, DIN 8077, DIN 8078 (or
equal products))
)) with surface-mounted
surface fire stop collar PROMASTOP®-FC on soft
penetration seal PROMASTOP®-CC with EI90 – u/u:
IBS – Institut für Brandschutztechnik und Classification Report No.: 316100407-A-en
Sicherheitsforschung Gesellschaft m. b. H. Date: 08.11.2016
A - 4020 Linz, Petzoldstrasse 45 Page 100 of 103
Akkreditierte Prüf-,, Inspektions-
Inspektions und Zertifizierungsstelle Sponsor: PRTC
PP-H and PP-R pipes (e.g. complying with OENORM B 5174-1, 1, DIN 8077, DIN 8078 (or
equal products)) with surface-mounted
surface firestop collar PROMASTOP®-FC on soft penetration
seal PROMASTOP®-CC CC with EI120 – u/u:
IBS – Institut für Brandschutztechnik und Classification Report No.: 316100407-A-en
Sicherheitsforschung Gesellschaft m. b. H. Date: 08.11.2016
A - 4020 Linz, Petzoldstrasse 45 Page 101 of 103
Akkreditierte Prüf-,, Inspektions-
Inspektions und Zertifizierungsstelle Sponsor: PRTC
4.3.12 Distances
Supporting distances:
The installations must be suspended ≤ 250 mm on both sides from walls or on the top of
floor constructions.
The results achieved using a rigid standard supporting construction shall be valid for
separating construction products
products of concrete or masonry having a similar or higher
thickness and density as the tested ones.