Professional Documents
Culture Documents
Civil Estimate
S NO
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
30 BED PREFAB WARD FOR COVID CARE
Civil Estimate
Description
DISMANTLING
Dismantling plastered brickwalls in cement mortar including cleaning, stacking the useful materials as directed
by engineer-in-charge and dumping the dismantled debris as indicated at site, levelling, consolidating, all complete
as directed and disposing the debris away from site all complete as directed.
Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats, architrave,
holdfasts etc. complete and stacking within 50 metres lead : Of area 3 sq. metres and below
Dismantling wood work in frames, trusses, purlins and rafters up to 10 metres span and 5 metres height including
stacking the material within 50 metres lead : Of sectional area 40 square centimetres and above
EARTH WORK
Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in
depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50
m and lift upto 1.5 m, as directed by Engineer-in-charge.
Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not
exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift
upto 1.5 m.
Filling with contractor's own earth ( excluding rock) in trenches, plinth, sides of foundations etc. in layers not
exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift up
to 1.5 m as per direction of site Engineer-in-charge
CEMENT CONCRETE
Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering -
All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal
size)
RCC
Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering,
shuttering, finishing and reinforcement - All work up to plinth level : 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III):
3 graded stone aggregate 20 mm nominal size)
Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering,
shuttering, finishing and reinforcement - All work up to plinth level :1:2:4 (1 cement : 2 coarse sand (zone-III) : 4
graded stone aggregate 20 mm nominal size)
Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all
complete upto plinth level.
Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone - III) : 6 graded
stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed
and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the
top smooth.
FORM WORK
Centering and shuttering including strutting, propping etc. and removal of form for all heights : Lintels, beams,
plinth beams, girders, bressumers and cantilevers
Centering and shuttering including strutting, propping etc. and removal of form for : Foundations, footings, bases of
columns, etc. for mass concrete
Centering and shuttering including strutting, propping etc. and removal of form for all heights : Lintels, beams,
plinth beams, girders, bressumers and cantilevers
MASONRY WORK
Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete
1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) upto plinth level with :Cement
mortar 1:6 (1 cement : 6 coarse sand)
PLASTERING
12 mm cement plaster finished with a floating coat of neat cement of mix :1:4 (1 cement: 4 fine sand)
STEEL WORK
Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including
welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary
stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash
fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable
arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members
shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).
Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting,
hoisting, fixing in position and applying a priming coat of approved steel primer all complete.
Structural steel work in single section, fixed with or without connecting plate,including cutting, hoisting, fixing in
position and applying a priming coat of approved steel primer all complete.
Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting,
hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with
special shaped washers etc. complete. Hot finished welded type tubes
ALUMINUM WORK
Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built
up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to
IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up
the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc.
Aluminium sections shall be smooth, rust free,straight, mitred and jointed mechanically wherever
required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel
screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing,
paneling and dash fasteners to be paid for separately) : For fixed portion Powder coated aluminium
(minimum thickness of powder coating 50 micron)
Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built
up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to
IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up
the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc.
Aluminium sections shall be smooth, rust free,straight, mitred and jointed mechanically wherever
required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel
screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing,
paneling and dash fasteners to be paid for separately) : For shutters of doors, windows & ventilators
including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever
required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for
separately) Powder coated aluminium (minimum thickness of powder coating 50 micron)
Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with
EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of
engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item):With float glass panes
of 5 mm thickness (weight not less than 12.50 kg/ sqm)
Providing and fixing aluminium tubular handle bar 32 mm outer dia, 3.0 mm thick & 2100 mm long with
SS screws etc .complete as per direction of Engineer-in-Charge.Polyester powder coated minimum
thickness 50 micron aluminium tubular handle bar
Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood
particle board conforming to IS: 12823 Grade l Type ll, in panelling fixed in aluminum doors, windows
shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural
drawings and directions of engineer-in-charge. Pre-laminated particle board with decorative lamination
on both sides
Providing and fixing aluminium tubular handle bar 32 mm outer dia, 3.0 mm thick & 2100 mm long with
SS screws etc .complete as per direction of Engineer-in-Charge.Polyester powder coated minimum
thickness 50 micron aluminium tubular handle bar
Providing and fixing aluminium hanging floor door stopper ISI marked anodised (anodic coating not less
than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade with necessary
screws etc. complete. With twin rubber stopper
Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand
logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm),
with necessary accessories and screws etc. complete.
Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete :
150x10 mm
Providing and fixing bright finished brass 100 mm mortice latch and lock with 6 levers and a pair of
lever handles of approved quality with necessary screws etc. complete.
Providing and fixing factory made uPVC white colour casement/casement cum fixed glazed windows
comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles
duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process
of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of
appropriate dimension, EPDM gasket, stainless steel (SS 304 grade) friction hinges, zinc alloy (white
powder coated) casement handles, G.I fasteners 100 x 8 mm size for fixing frame to finished wall,
plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame & sash shall be
mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including
drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between
frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of
required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-
Charge. (Single / double glass panes and silicon sealant shall be paid separately) Note: For uPVC frame,
sash and mullion extruded profiles minus 5% tolerancein dimension i.e. in depth & width of profile shall
be acceptable. Casement window single panel with S.S. friction hinges (300 x 19 x 1.9 mm), made of
(small series) frame 47 x 50 mm & sash 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and
single glass pane glazing bead of appropriate dimension. (Area of window upto 0.75 sqm.)
PANEL WORK
Supply and fixing of PUF panel Doors, windows, partitions, roof made up of GI powder coated 0.47mm thick sheet
on both sides, with 50 mm thick class 'O' PUF of min.38kg/m3 density sandwiched in between. The GI sheet shall
have 80 micron thick powder coating by hot dip galvanizing with zinc coating not less than 180gm/sqm on both
sides of the panel. Scope includes bottom runner, inter connecting profiles, fixing arrangements, silicon sealant
application and all other accessories required to complete the work as per site requirement. Colour: Powder coated,
complete with all necessary hardware, accessories, fittings and fixtures, as per description in individual items,
technical specifications, drawings and instructions of the Engineer-Incharge. including GI Frames.
ROOFING
Providing at all heights, levels and locations 0.45 mm thick Galvalume sheet of Alloy 31500/31000/40800,
conforming to IS 1254, IS 737, IS 2676. The sheet shall be fixed using self drilling/self tapping SS screws of size
5.5x65 mm with EPDM seal complete upto required pitch in horizontal, vertical or curved surfaces i/c cutting to
size and shape where required as per the direction of Engineer-in-Charge. The rate shall be inclusive of all screws,
seal, ridge, labour, scaffolding, machinery for fixing and approved sealant where required etc. but excluding the cost
of purlins, rafters and trusses.
FLOORING
Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water
absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on
20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including
grouting the joints with white cement and matching pigments etc., complete.Size of Tile 600x600 mm
Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be
specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours,
shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick Cement Mortar 1:4 (1 Cement
: 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including pointing the joints with white
cement and matching pigments etc., complete.
Providing and laying Vitrified tiles in different sizes (thickness to be specified by the manufacturer),
with water absorption less than 0.08% and conforming to IS: 15622, of approved brand & manufacturer,
in all colours and shade,in wall tiles, skirting, riser of steps, laid with cement based high polymer
modified quick set tile adhesive (water based) conforming to IS: 15477, in average 6 mm thickness,
including grouting of joints (Payment for grouting of joints to be made separately).Size of Tile 600x600
mm make Kajaria/ Restile/Johnson or equivqlent (Basic cost of tile - Rs.85/sft).Any difference in basic
price and OHP at the time of approval shall be adjusted for the laid area.No extra shall be payable for
forming any pattern in the flooring like border, cut tiles,etc.
Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be
specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green,
black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm
thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg
per sqm, including pointing in white cement mixed with pigment of matching shade complete.
Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine
cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size,
approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse
sand), joint treated with white cement, mixed with matching pigment, epoxy touch ups, including
rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.
Granite of any colour and shade. Area of slab over 0.50 sqm
Chequered terrazo tiles 22 mm thick with graded marble chips of size up to 6 mm in floors, jointed with
neat cement slurry mixed with pigment to match the shade of the tiles, including rubbing and polishing
complete, on 20 mm thick bed of cement mortar 1:4 (1 cement :4 coarse sand) : Dark shade pigment
using ordinary cement
FALSE CEILING
Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in true horizontal level,
suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/ sqm, both
side inclusive) consisting of main "T" runner with suitably spaced joints to get required length and of size 24x38
mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross "T" of size 24x25
mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main "T" at 600 mm center to center
to form a grid of 1200x600 mm and secondary cross "T" of length 600 mm and size 24x25 mm made of 0.30 mm
thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and
wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required
cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T"
runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5
mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85 x
30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections
shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed
by Engineer-in-charge. 12.5 mm thick square edge PVC Laminated Gypsum Tile of size 595x595 mm, made of
Gypsum plasterboard,manufactured from natural gypsum as per IS 2095 part I and laminated with white 0.16mm
thick fire retardant PVC film on the face side and 12micron metalized polyester on the back side with all edges
sealed with the face side PVC film which goes around and wraps the edges and is bonded to the edges and the back
side metalized polyester film so as to make the tile a completely sealed unit.
PAINTING
Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer’s
specifications including appropriate priming coat, preparation of surface, etc. complete. On steel work
Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer,
over the plastered wall surface to prepare the surface even and smooth complete.
Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface : Water
thinnable cement primer
Finishing with Deluxe Multi surface paint system for interiors using Primer as per manufacturers specifications :
Two or more coats applied on walls @ 1.25 ltr/10 sqm over and including one coat of Special primer applied @
0.75 ltr /10 sqm
Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/ 10
sqm over an under coat of primer applied @ 0.80 ltr/ 10 sqm of approved brand and manufacture
Providing and fixing PTMT Waste Coupling for wash basin and sink, of approved quality and colour. Waste
coupling 31 mm dia of 79 mm length and 62mm breadth weighing not less than 45 gms
Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. Semi rigid
pipe 32 mm dia
Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 25 mm nominal bore
Providing and fixing PTMT grating of approved quality and colour. Rectangular type with openable circular lid 150
mm nominal size square 100 mm diameter of the inner hinged round grating.
Providing and fixing C.P. brass long nose bib cock of approved quality conforming to IS standards and weighing
not less than 810 gms. 15 mm nominal bore
Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10
litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever),
conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and
floors wherever required : W.C. pan with ISI marked white solid plastic seat and lid
Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to
Eureopean type W.C. of quality and make as approved by Engineer - in - charge.
Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes
jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of
Engineer-in-Charge 25 mm dia 10 Kgf/cm2- External work - Exposed on wall
Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes
jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of
Engineer-in-Charge 32 mm dia 10 Kgf/cm2 - External work- Exposed on wall
Providing and fixing PVC pipes, fittings including fixing the pipe with clamps at 1.00 m spacing. This includes
jointing of pipes & fittings with one step PVC solvent cement and testing of joints complete as per direction of
Engineer-in-Charge 50 mm dia 10Kgf/cm2 - External work - Exposed on wall
Supplying and installing ready made PVC Septic tank including the cost of carriage, trenching, placing at the level
below ground level as specified as per the direction of engineer in charge (Provision for CC/RCC/Sand/06mm
aggregate for the preparation of bed shall be paid separately) 3. 25 to below 35 flush capacity
Providing and fixing PVC pipes includings jointing of pipes with one step PVC solvent cement, trenching, refilling
& testing of Joints complete as per direction of engineer in charge.110 mm dia 6Kgf/cm2
Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with
1:1.5:3 mix (1 cement : 1.5 coarse sand (zone- III) : 3 graded stone aggregate 20 mm nominal size), foundation
concrete 1:4:8 mix (1 cement : 4 coarse sand (zone- III) : 8 graded stone aggregate 40 mm nominal size), inside
plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement
and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal
size) finished with a floating coat of neat cement complete as per standard design :Inside size 90x80 cm and 45 cm
deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame
to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) :With common burnt clay F.P.S. (non
modular) bricks of class designation 7.5
Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete
with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.
Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass
screws with concealed fitting arrangement of approved quality and colour. 600mm long towel rail with
total length of 645mm, width 78mm and effective height of 88mm, weighing not less than 190gms.
Providing and fixing PTMT liquid soap container 109mm wide, 125mm high and 112mm distance from
wall of standard shape with bracket of the same materials with snap fittings of approved quality and
colour. weighing not less than 105 gms.
Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality
conforming to IS:8931 :15mm nominal bore
Unit Qty Rates Amount
Kg 4,459.08 85 379021.8
M 50 250 12500
M 90 350 31500
-
M 60 790 47400
M 30 790 23700
Total 5924184
ELECTRICAL WORKS.
SL No. DESCRIPTION QTY
Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC
insulated copper conductor single core cable in surface / recessed medium class PVC conduit,
with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm
FRLS PVC insulated copper conductor single core cable etc. as required. switch, modular plate,
suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor
single core cable etc. as required.
Group C 68
2 Wiring through PVC conduit
Wiring for circuit/submain wiring along with earth wire with the following sizes of FR PVC
insulated copper conductor, single core cable in surface/recessed medium class PVC conduit as
required.(Make:Havells/Finolex/V-guard/Polycab)
a 2X1.5 sq.mm + 1X1.5 sq.mm earth wire 224
b 2X2.5 sq.mm + 1 X2.5 sq mm earth wire 810
c 2 X 4 sq. mm + 1 X 4 sq. mm earth wire 794
d 2 X 6 sq. mm + 1 X 6 sq. mm earth wire 25
Supplying and drawing following pair 0.5 sq mm FR PVC insulated annealed copper conductor,
unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required.
a 2 Pair 88
4 Modular type blanking plate:
Supplying and fixing modular blanking plate on the existing modular plate & switch box
10
excluding modular plate as required.
8 outlet, with 2 pole and earth, metal enclosed plug topalong with 20 A "C" curve, SP, MCB, in 15
sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and
complete with connections, testing and commissioning etc. as required
Installation, testing and commissioning of ceiling fan, including wiring the down rods of
10.2 standard length (upto 30 cm) with 1.5 sq. mm FRLS PVC insulated, copper conductor, single 17
core cable etc. as required.
Supplying and fixing two module stepped type electronic fan regulator on the existing modular
10.3 17
plate switch box including connections but excluding modular plate etc. as required.
Extra for fixing the louvers/ shutters complete with frame for a
10.5 10
exhaust fan of all sizes.
11 LAYING OF CABLES
CABLE LAYING
Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1
KV grade of following size on wall surface as required.
Upto 35 sq. mm (clamped with 1mm thick saddle) 190
12 END TERMINATION
Supply and making end termination with brass compression gland, earth clip and aluminium
lugs for following size of PVC insulated and PVC sheathed/XLPE aluminium conductor cable
fo 1.1KV grade as required.
a 3.5 x 35 sq.mm(32mm) 2
b 4 x 25 sq.mm(28mm) 2
c 4 x 10 sq.mm(28mm) 2
Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 V, TPN
MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 A
13 tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without
MCBs and incomer ) as required . (Note : Vertical type MCB TPDB is normally used where 3
phase outlets are required.)
4 way (4 + 12), Double door 1
Supplying and fixing following rating, four pole, 415 V, isolator in the existing MCB DB
13.1
complete with connections, testing and commissioning etc. as required.
100 A 1
14 S/F of TPN MCB DB
Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB
distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus
bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But
without
MCB/RCCB/Isolator)
8 way (4 + 24), Double door 2
16 S/F OF SP MCB
Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, “C” curve, miniature circuit breaker
suitable for inductive load of following poles in the existing MCB DB complete with
connections, testing and commissioning etc. as required.
a 6/32 A SP MCB 60
18 EARTHING
Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing
a masonry enclosure with cover plate having locking arrangement and watering pipe etc. with 1
charcoal/ coke and salt as required
Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and
b providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2
2.7 metre long etc. with charcoal/ coke and salt as required.
Providing and fixing 4.00 mm dia copper wire on surface or in recess for loop earthing along
c 125
with existing surface/ recessed conduit/ submain wiring/ cable as required.
Providing and fixing earth bus of 50 mm X 5 mm copper strip on
d 0.45
surface for connections etc. as required.
19 Supply and installation of 10MP 8-Port Gigabit PoE Managed Switch with its all accessories 1
Supply and installation of intercom system with (Extn. to Extn. Call between 16 Intercoms),
20 Call transfer, call hold and busy transfer, Call parking, Outgoing local/std/isd call restriction, 1
Call pick-up form any extension and many more
Supply,laying and termination of 10 pair telephone terminal block housed in engineering plastic
20.1 1
box with transparent hinged door
Supply,installation, testing and commissioning of 600x600 mm square type cool white, pure
white LED recess mounted fixture with Integrated Driver & Backlight Technology with a
minimum system efficiency of 95 w/Lm, Standard CCT: 3000k* 4000 k & 6500k, high colour
rendering CRI>80, with high efficiency driver, minimum of 35000 hours working life and surge
21 protection -4kv(light variant as decided by engineer in charge), Each module should be tested 30
and QC approved by competent authority and same to be furnished before electrical engineer
HLL Life Care Ltd before purchase or else any higher or equivalent versions/specification may
be used without change in cost, only at the discretion of HLL/NHM Engineer at site or Electrical
Engineer( HLL ) (Make: AS per CPWD standards)
Supply of 20W LED tube fitting sleek with decorative end cap, powder coated CRCA steel
21.1 channel complete with all electrical accessories like electronic ballast, lamp holder, 20W LED 4
lamp etc complete as required.
21.1 Supply and fixing of 18 W LED bulb and batten with its all accessories.[ISI MAKE] 9
Supply and installation of 1200 mm sweep ceiling fan, white colour, 5 star rated as Per BEE
22 17
complete with blades, down rod shackle, canopy etc.
Supplying and fixing two module stepped type electronic fan regulator on the existing modular
22.1 11
plate switch box including connections but excluding modular plate etc. as required.
Supply and installation of wall fan (400 mm), white colour, 5 star rated as per BEE complete
22.2
with blades, casing , wall mounting accessories etc(Make Havells/bajaj/usha/V-guard/crompton)
1
Supply and installation EXHAUST FAN,SHUTTER TYPE white colour, 9" OR 10" star rated
22.3 8
as per BEE complete with its all accessories(
23 CABLE SUPPLY
Supplying the following PVC insulated and PVC sheathed/XLPE power cable of 1.1 KV grade
as per CPWD standards as required.
a 3.5 x 35 sq.mm 90
Supply of following PVC /XLPE insulated armoured cable with copper conductors for working
23.1 voltages up to and including 1100 volts conforming IS 1584/part I/ 1988 for PVC IS 7098 part I
for XLPE (Make:Havells/ Glostar/Nicco/Finolex/Polycab)
25 S/F of TP MCB
Supplying and fixing 6 amps to 63 amps rating, 415 Volts, "C" series, miniature cirucuit breaker
suitable for lighting and other loads of following poles in the existing MCB DB complete with
connections, testing and commissioning etc as required.(Make: Legrand/Havells/HPL)
a 63A TP MCB 2
Supply and installation of Co2 Fire Extinguisher (Trolley Mount - Wheel Operating) Type
26 4.5KG with MS clamps etc. for fixing on wall/wooden partition with 01 year warranty. I.S. No. 5
13849.
Supply and fixing RJ45 Keystone IO jack with cover and face plate, including
27 2
crimbing/Punching of UTP 4 Pair CAT 6E LAN Cables on both ends with RJ45 Connector.
Supply and installation of PVC raceway of size (50x 50mm) 2 mtr length with its all accessories
28 65
29 Supply and fixing of Basic landline phone set complete with its all accessories. 1
30 Supply and fixing call bell/buzzer suitable for single phase, 230 V complete as required. 1
31 SPLIT AIR CONDITIONER
Supply, installation, testing and commissioning of 2 TR, Hot and Cold, 3 star rated (as per BEE)
Air Cooled High Wall mounted Inverter type Split Air Conditioner consisting of high wall
mounted type room unit (fan coil) with cordless remote control and one number outdoor
condensing unit comprising of enegy efficient suitable rotary compressor for operation on single
phase, 230 V, 50Hz supply, fixing the outdoor unit on a raised platform as per manufacturers
recommendation and fixing of room (fan coil) unit on wall, standard 4 m distance refrigerant
1 7
copper piping with 13mm nitrile rubber insulation, providing and making interconnection
between room & condenser as per site conditions, comprising of 1" dia drain PVC pipe with
insulation 4m, canvas connections, full electrical cabling from power plug near indoor unit and
to outdoor unit, ODU MS stand, first charge refrigerant gas, suitable stabilizer etc complete as
required. Make: Voltas, Toshiba, Blue Star, Siemens, Mitsubuishi, Hitachi or equivalent or as
per the approval of Engineer in Charge
Supplying, installation, testing & commissioning sector panel suitable for following zones,
complete with visual indications for short circuit fault, open circuit fault, fire condition and all
a
other standard facilities as per IS:2189 with mimic diagram for all area/zone covered, complete
with all connections, interconnections as required. 2/4 ZONE-1 Each
Supplying, installation, testing & commissioning of smoke detector with builtin LED and
b
mounting base complete with all connections etc. as required.-24 Each.
Supplying, installation, testing & commissioning of manual call boxes of MS construction in 1
c surface/recess with stainless steel chain & hammer assembly complete with glass and push
button etc. as required.3 Each.
Supplying, installation, testing & commissioning fire alarm sounder with facility to make
d announcement, mounted in A.B.S. box with hinged cover plate & suitable for operation with
amplifier i/c line matching transformer etc. complete as required. 3 Each
Supplying & laying of 2x1.5 sqmm fire alarm armoured cable, 600/1000V rated with annealed
e copper conductor having XLPE insulation, steel wire armouring & FRLS outer sheath
complete as required. 425 Metre
33 SITC of 82.5 KVA DG Set
SITC OF 82.5 KVA DIESEL GENERATOR .
1 1
Providing, Installing, Testing and Commissioning of ‘Silent Type’ Diesel Generating set along
with having Prime Power Rating of 82.5 KVA, 415 volts at 1500 RPM, 0.8 lagging power
factor at 415 V suitable for 50 Hz, 3 phase system & for 0.85 Load Factor and consisting of
Diesel engine 4 stroke water cooled, electric start, of suitable BHP at 1500 RPM suitable for
above output of alternator at 40 Degree C, 50% RH & at 1000 Meter MSL andconforming to BS
5514, BS 649, IS 10000, capable of taking 10% over loading for one hour after 12 hours of
continuous operation. The engine will be fitted complete with all the required accessories and
Synchronous alternator rated at 82.5 KVA, 415 volts at 1500 RPM, 3 phase 50 Hz, AC supply
with 0.8 lagging power factor at 40 Degree C, 50% RH & at 1000 Meter MSL. The alternator
shall be having SPDP enclosure, brushless, continuous duty, self-excited and self-regulated
through AVR conforming to IS: 4722/BS 2613 suitable for tropical conditions and with class-
1 F/H insulation, provision for CPWD/EI/EB approved AMF panel, Base Frame, Fuel Tank, 1
Battery with leads and other accessories with type competent approved Canopy as a complete
set, Including Supply, fabrication and Erection of Exhaust piping, supplying and fixing of AMF
controller switch, Supply & laying of PVC insulated and PVC sheathed armoured aluminium
power cable including excavation, sand cushioning, protective covering and refilling the trench ,
Earthing as per standards and civil works, platform. Charges for Preparation of all drawings
submitting and getting approval from Electrical Inspectorate, submitting of Completion
certificates and arranging inspection, getting sanction and energisation certificates from
Electrical Inspectorate ,CPWD& EB, obtaining power allocation & power connection etc. for
commissioning of the whole installation in the premises including generator etc. Contractor has
to arrange load test at site or at factory without any additional cost or claim. Including First fill
of lube oil and Engine safeties – LLOP, HWT, Initial filling of diesel for standard testing
procedure up to 6 hours minimum and 12 hours maximum.
34 CCTV
Supply, installation, testing and commissioning of IP based IR WDR minidome day night colour
Camera, 1/3" progressive CMOS, 2 MP, 3 - 10 mm MFZ, night vision compatible,IR range upto
a 15 mtrs PoE, inbuilt micro SD card,Ethernet port, H.264, IP 66, ONVIF, UL, FCC & CE
certified. All mounting accessories shall be included Make:Hikvision/CP Plus/Honeywell
Make:Hikvision/CP Plus/Honeywell.-4 Each
b Supply and fixing of 3+1 coaxial pure copper CCTV camera cable -172 Metre
c Supply and fixing of BNC connector and DC jack for CCTV Cameras-8 Nos
1
d Supply and fixing of 12V 36 Amps SMPS with its all accessories-1 Each
e Supply and fixing of 1 TB Hard disk Drive with its all accessories-1 Each
f Supply and fixing of 4 Channel DVR with its all accessories-1 Each.
Supply and installation of wall mount 6 U CCTV DVR/NETWORK Cabinet Box with lock
g
including 3 power socket plug -1 Each.
Supply and installation of 10MP 5-Port Gigabit PoE Managed Switch with its all accessories-1
h
Each
NEGATIVE PRESSURE
35 DESCRIPTION QTY
PART A
Supply & installation charges of exhaust inline fan 8000 cfm. [ CPWD APPROVED ISI
1 1
MAKE]-exhaust(CABINET)
2 Lifting , shifting ,Installation,Testing & Commissioning of inline fans 1
3 Supply & fixing charges of Gravity Louver with its all accessories 1
4 Supply and fixing of electrical panel for fans 1
PART B
FILTERATION FOR ICU STANDARDS
Supply, installation, testing and balancing of Powder coated/Anodised extruded aluminium
5 construction, outlet air louvers with bird screen, volume damper & filter for exhaust air as per 1
specifications and approved drawings.
6 Providing & fixing charges of hepa filters (EU13)- Exhaust Duct 1
PART C
7 DUCT/DUCT INSULATION / ACOUSTIC INSULATION
Supply, installation, balancing and commissioning of factory fabricated GSS sheet metal
rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter dampers,
vanes,
hangers, supports etc. as per approved drawings and specifications of following sheet thickness
complete as required.
7.1 Thickness 0.63 mm sheet 85
7.2 Thickness 0.80 mm sheet 15
FIRE DAMPER
Supplying, Fixing,testing and commissioning of fire dampers in supply air duct/main branch and
return air path as and where required of required sizes i/c control wiring,the damper shall be
motorized and spring return so as to close the damper in the event of power failure automatically
8
and open the same in case of power being restored. The spring return action shall be inbuilt
mechanism and not externally mounted. The damper shall also be closed in the event of fire
signal complete as required and as per specifications.
Fire Damper 1
Actuator 1
Supply & fixing of powder coated extruded aluminium SUPPLY AIR DIFFUSER with
10 aluminium volume control dampers as per specification with anti smudge ring & removable 10.8
core.
Supply & fixing of powder coated extruded aluminium RETURN AIR DIFFUSER with louvers
11 10.8
without volume control dampers as per specification anti smudge ring & removable core.
Supplying & fixing of powder coated extruded aluminium Return Air Grills with louvers but
12 5
without volume control dampers complete as required
UNIT Rates Amount
Metre 20 4480
Metre 35 28350
Metre 42 33348
Metre 57 1425
Metre 34
Each
70
Each 410
Each 590
Each 98
Each 110
Each 120
Each 144
Each 40
Metre 29
Each
610
Metre 30
Metre 35
Each
1800
Each
2500
Each
370
Each 1600
Each
2200
Metre 70
Each 1560
Each 1500
Each 900
Each 1800
Each 1200
Each 2400
Each 3200
Each 1900
Each 500
Each 120
Each 6000
Set
11000
set
14000
Metre
42
Metre
800
Each
Set 59620
Each 820
Each
1400
Each
330
Each 230
Each 2200
Each 150
Each 3500
Each 250
Metre 335
Metre 824
Metre 600
Each 4200
Each 1100
No
2800
Each
1550
No
250
Set 1050
Each 225
NO
60000
10200
1350
Ls 13132
650
800
132
Each
Each
UNIT
Nos. 200000
200000
Ls 50000 50000
Nos. 3200 3200
Nos. 30000 30000
Sqm 2200
2200
Nos 14800 14800
sq.m 3400
36720
sq.m 3200
34560
sq.m 3200
16000
Total 705515