Professional Documents
Culture Documents
Max Power 35 W BTL × 4 CH Audio Power IC: Features
Max Power 35 W BTL × 4 CH Audio Power IC: Features
TA8276H
Max Power 35 W BTL × 4 ch Audio Power IC
1 2002-02-13
TA8276H
Block Diagram
C5
C3
1 20 6
TAB VCC1 VCC2
OUT1 (+)
9
IN1
11 PW-GND1 8 RL
C1
OUT1 (-)
7
OUT2 (+)
5
IN2
12 PW-GND2 2 RL
C1
OUT2 (-)
3
AUX IN
16
C6
OUT3 (+)
17
IN3
15 PW-GND3 18 RL
C1
OUT3 (-)
19
OUT4 (+)
21
IN4
14 PW-GND4 24 RL
C1
OUT4 (-)
23
R1
C4
: PRE-GND
: PW-GND
2 2002-02-13
TA8276H
Caution and Application Method
(Description is made only on the single channel.)
Amp. 2A
Amp. 1
Input
Amp. 2B
ON OFF 0~1.5
OFF ON 3~VCC Figure 2 With pin 4 set to High,
Power is turned ON
Adjustage of Stand-by SW
(1) Since VCC can directly be controlled to ON or OFF by the microcomputer, the switching relay can be
omitted.
(2) Since the control current is microscopic, the switching relay of small current capacity is satisfactory
for switching
3 2002-02-13
TA8276H
RELAY
Large current capacity switch
BATTERY BATTERY
– Conventional Method –
DIRECTLY FROM
Small current capacity switch MICROCOMPUTER
BATTERY BATTERY
Figure 3
<Recommended Application>
ATT – VMUTE
20
I (100 mA)
R1 A 10 kW 5 kW
IMUTE (OFF) 0
22
(dB)
C4
IMUTE -20
Mute attenuation ATT
VMUTE
-40
-60
<Application for pulled up> VCC = 13.2 V
Po = 10 W
-80
PL = 4 W
I (100 mA) f = 1 kHz
R1 -100
BW = 400~30 kHz
IMUTE (OFF) 22
0 0.4 0.8 1 1.2 1.6 2 2.4 2.8 3
C4
IMUTE
Point A voltage: VMUTE (V)
VMUTE
4 2002-02-13
TA8276H
4. AUX Input (pin 16) 20 dB AMP.
The pin 16 is for input terminal of AUX
amplifier.
The total gain is 0 dB by using of AUX amplifier. IN
Therefore, the m-COM can directly drive the OUT (+)
AUX amplifier.
BEEP sound or voice synthesizer signal can be
input to pin 16 directly. OUT (-)
When AUX function is not used, this pin must be AUX AMP
AUX-IN
connected to PRE-GND (pin 13) via a capacitor. m-COM 16
-20 dB
5V
25
V25
OUTPUT CLIP
Q1 5V
DETECTOR
OUTPUT SHORT
PROTECTOR
5V
LED/LCD (Flashing)
25 m-COM
Figure 8 Application 1
5 2002-02-13
TA8276H
5.3 Prevention of speaker burning accident (In Case of Rare Short Circuit of Speaker)
When the direct current resistance between OUT + and OUT - terminal becomes 1 W or less and output
current over 4 A flows, this IC makes a protection circuit operate and suppresses the current into a speaker.
This system makes the burning accident of the speaker prevent as below mechanism.
Abnormal output offset voltage (voltage between OUT + and OUT -) over 4 V is made by the external
circuit failure.(Note 1)
¯
The speaker impedance becomes 1 W or less as it is in a rare short circuit condition.
¯
The current more than 4 A flows into the speaker and the speaker is burned.
Less than 4 W
Speaker impedance
About 1 W 4W
Figure 9
5.4 Applications
When output terminals short-circuit to VCC or GND, the voltage of 25pin is fixed to “L”.
And when shorting OUT + to OUT -, “L” and “H” are switched according to an input signal.
Therefore, it is possible to judge how the power IC condition is if a micro-controller detects the
25pin voltage that is smoothed out with LPF.
It is recommend that the threshold voltage (Vth) is set up as higher as possible because output level
of LPF is changed according to an input signal.
(for example, Vth is set up to 4 V if 25pin is pulled up to 5 V line.)
5V
Output power
Figure 10
6 2002-02-13
TA8276H
6. Output Clip Detection Function (pin 25)
The output clip detection terminal of pin 25 has the open collector output structure on chip as shown in
Figure 11. In case that the output waveform is clipping, the clip detection circuit is operated and NPN Tr. is
turned on.
It is possible to improve the audio quality with controlling the volume, tone control circuit through L.P.F.
smoothing circuit as shown in Figure 11.
In case of being unused this function, use this IC as open connection on pin 25.
(Application) 5V
25
OUTPUT CLIP
DETECTOR
Figure 11
(A)
(B)
(C)
5V
GND t
7 2002-02-13
TA8276H
Maximum Ratings (Ta = 25°C)
Electrical Characteristics
(unless otherwise specified, VCC = 13.2 V, f = 1 kHz, RL = 4 W, Ta = 25°C)
Test
Characteristics Symbol Test Condition Min Typ. Max Unit
Circuit
Quiescent current ICCQ ¾ VIN = 0 ¾ 200 400 mA
POUT MAX (1) ¾ VCC = 14.4 V, max Power ¾ 35 ¾
POUT MAX (2) ¾ VCC = 13.7 V, max Power ¾ 31 ¾
Output power W
POUT (1) ¾ VCC = 14.4 V, THD = 10% ¾ 23 ¾
POUT (2) ¾ THD = 10% 17 20 ¾
Total harmonic distortion THD ¾ POUT = 5 W ¾ 0.02 0.2 %
Voltage gain GV ¾ VOUT = 0.775 Vrms (0 dBm) 24 26 28
dB
Voltage gain ratio DGV ¾ VOUT = 0.775 Vrms (0 dBm) -1.0 0 1.0
VNO (1) ¾ Rg = 0 W, DIN45405 ¾ 0.12 ¾
Output noise voltage mVrms
VNO (2) ¾ Rg = 0 W, BW = 20 Hz~20 kHz ¾ 0.10 0.35
frip = 100 Hz, Rg = 620 W
Ripple rejection ratio R.R. ¾ 40 50 ¾ dB
Vrip = 0.775 Vrms (0 dBm)
Rg = 620 W
Cross talk C.T. ¾ ¾ 65 ¾ dB
VOUT = 0.775 Vrms (0 dBm)
Output offset voltage VOFFSET ¾ ¾ -150 0 150 mV
Input resistance RIN ¾ ¾ ¾ 90 ¾ kW
Stand-by current ISB ¾ Stand-by condition ¾ 2 10 mA
VSB H ¾ Power: ON 3.0 ¾ VCC
Stand-by control voltage V
VSB L ¾ Power: OFF 0 ¾ 1.5
VM H ¾ Mute: OFF Open ¾
Mute control voltage (Note 2)
VM L ¾ Mute: ON, R1 = 10 kW 0 ¾ 0.5 V
Mute: ON,
Mute attenuation ATT M ¾ VOUT = 7.75 Vrms (20 dBm) at 80 90 ¾ dB
Mute: OFF.
Note 2: Muting function have to be controlled by open and low logic, which logic is a transistor, FET and m-COM port
of IMUTE > 250 mA ability.
This means than the mute control terminal : pin 22 must not be pulled-up.
8 2002-02-13
TA8276H
Test Circuit
0.1 mF
3900 mF
C5
C3
1 20 6
TAB VCC1 VCC2
OUT1 (+)
9
0.22 mF IN1
11 PW-GND1 8 RL
C1
OUT1 (-)
7
OUT2 (+)
5
0.22 mF IN2
12 PW-GND2 2 RL
C1
OUT2 (-)
3
0.22 mF AUX IN
16
C6
OUT3 (+)
17
0.22 mF IN3
15 PW-GND3 18 RL
C1
OUT3 (-)
19
OUT4 (+)
21
0.22 mF IN4
14 PW-GND4 24 RL
C1
OUT4 (-)
23
1 mF
C2
R1
C4
: PRE-GND
: PW-GND
9 2002-02-13
TA8276H
(%)
10 10
T.H.D
T.H.D
Total harmonic distortion
0.01 0.01
0.1 1 10 100 0.1 1 10 100
RL = ¥
(%)
VIN = 0
(mA)
T.H.D
300
ICCQ
0.1 OUT3
OUT1
Total harmonic distortion
OUT2
Quiescent current
200
0.01
100 OUT4
VCC = 13.2 V
RL = 4 W
Pout = 5 W
0 0.001
0 10 20 30 10 100 1k 10 k 100 k
10 2002-02-13
TA8276H
VNO – Rg R.R. – f
300 0
VCC = 13.2 V VCC = 13.2 V
RL = 4 W
(mVrms)
-10 RL = 4 W
200
-30
Output noise voltage
150
-40
100
-50
50
-60
0 -70
10 100 1k 10 k 100 k 10 100 1k 10 k 100 k
C.T. (dB)
-20 RL = 4 W -20 RL = 4 W
-30 -30
Cross talk
Cross talk
-40 -40
-50 -50
OUT1 ® OUT2, 3
-60 -60 OUT2 ® OUT1
C.T. (dB)
-30 -30
Cross talk
Cross talk
-40 -40
OUT3 ® OUT4
-50 -50
OUT3 ® OUT1
OUT4 ® OUT3
-60 -60
11 2002-02-13
TA8276H
GV – f PD – POUT
40 70
35
60
(W)
30
(dB)
50 16 V
PD
25
GV
40
Power dissipation
20
Voltage gain
13.2 V
30
15
20
10
VCC = 13.2 V
9V
5 RL = 4 W 10
f = 1 kHz
VOUT = 0.775 Vrms (0 dBm) RL = 4 W
0 0
10 100 1k 10 k 100 k 0 5 10 15 20 25
PD MAX – Ta
120
① INFINITE HEAT SINK
(w)
RqJC = 1°C/W
Allowable power dissipation PD MAX.
40
20 ②
③
0
0 25 50 75 100 125 150
12 2002-02-13
TA8276H
Package Dimensions
13 2002-02-13
TA8276H
· TOSHIBA is continually working to improve the quality and reliability of its products. Nevertheless, semiconductor
devices in general can malfunction or fail due to their inherent electrical sensitivity and vulnerability to physical
stress. It is the responsibility of the buyer, when utilizing TOSHIBA products, to comply with the standards of
safety in making a safe design for the entire system, and to avoid situations in which a malfunction or failure of
such TOSHIBA products could cause loss of human life, bodily injury or damage to property.
In developing your designs, please ensure that TOSHIBA products are used within specified operating ranges as
set forth in the most recent TOSHIBA products specifications. Also, please keep in mind the precautions and
conditions set forth in the “Handling Guide for Semiconductor Devices,” or “TOSHIBA Semiconductor Reliability
Handbook” etc..
· The TOSHIBA products listed in this document are intended for usage in general electronics applications
(computer, personal equipment, office equipment, measuring equipment, industrial robotics, domestic appliances,
etc.). These TOSHIBA products are neither intended nor warranted for usage in equipment that requires
extraordinarily high quality and/or reliability or a malfunction or failure of which may cause loss of human life or
bodily injury (“Unintended Usage”). Unintended Usage include atomic energy control instruments, airplane or
spaceship instruments, transportation instruments, traffic signal instruments, combustion control instruments,
medical instruments, all types of safety devices, etc.. Unintended Usage of TOSHIBA products listed in this
document shall be made at the customer’s own risk.
· This product generates heat during normal operation. However, substandard performance or malfunction may
cause the product and its peripherals to reach abnormally high temperatures.
The product is often the final stage (the external output stage) of a circuit. Substandard performance or
malfunction of the destination device to which the circuit supplies output may cause damage to the circuit or to the
product.
· The products described in this document are subject to the foreign exchange and foreign trade laws.
· The information contained herein is presented only as a guide for the applications of our products. No
responsibility is assumed by TOSHIBA CORPORATION for any infringements of intellectual property or other
rights of the third parties which may result from its use. No license is granted by implication or otherwise under
any intellectual property or other rights of TOSHIBA CORPORATION or others.
14 2002-02-13