Professional Documents
Culture Documents
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
Factory menu entry: Press MENU, and then press 1999
Primary menu Secondary menu Value,remark
MDOE VGA,YPBPR,Selection
R-GAIN
G-GAIN
B-GAIN Front-end gain adjustment
ADC ADJUST
R-OFFSET
G-OFFSET
B-OFFSET Clamp level adjustment
AUTO ADC ADC automatically adjust
Input Source Source Selection
MODE Dynamic/Standard/Sotf/User
BRIGHTNESS BRIGHTNESS
CONTRAST CONTRAST
PICTURE MODE
COLOR COLOR
SHARPNESS SHARPNESS
TINT TINT
Copy all No function
inputsource Source Selection
TEMPERATURE Cool, Standard, Warm
R-GAIN
G-GAIN White level adjustment
W/B ADJUST B-GAIN
R-OFFSET
G-OFFSET Black level adjustment
B-OFFSET
Copy all No function
MIU Enable DDR spectrum enable
MIU0 Span Exhibition frequently wide
MIU Step Spread spectrum step
SSC SETTING LVDS enable LVDS spectrum enable
LVDS Span Exhibition frequently wide
LVDS Step Spread spectrum step
LVDS swing LVDS swing
Spectial set 2HOUR OFF 2hours power off enable
WDT Watch dog on/off
White pattern White pattern selection
Restore user default Factory reset
PVR_RECORDALL PVR Record on/off
Power Power mode selection
Mirror Mirror function selection
Ageing mode Ageing mode enable
VIF Vif 1 Vif set
Vif 2 Vif set
32
Vif 3 Vif set
Qmap adjsut PQ setting
PEQ PEQsetting
OverScan Overscan_resolution Reselution select
Overscan_hsize Adjust overscan H size
Overscan_hposition Adjust overscan H position
Overscan_vsize Adjust overscan V size
Overscan_vposition Adjust overscal V position
other Test pattern
UART DEBUG DEBUG ON/OFF
HDMI CEC/ARC CEC/ARC ON/OFF
Backlight Adjust backlight
CI+ key usb upgrade CI+ key usb upgrade
SW information SW information
MODE Feature Selection
OSD 0
OSD 25
Non-linear
OSD 50 Curve adjustment
OSD 75
OSD 100
Channel table1 KTC factory Frequecy table set
CI factory setting No function
Channel table2 KTC factory Frequecy table set
Channel dvbt KTC factory Frequecy table set
33
34
35
36
37
38
MSD6308 Program Software Burning Instruction
1. Connect burning board and computer; connect burning board and waiting burning main board VGA
socket with VGA connecting wire.
ISP burning
board
To PC USB
interface
39
4. Sorting set the burning board terminal and computer interface make sure the two are all set as automatic
connecting. same as above .
40
5.
6. Click view in toolbar in the main menu, click the second( count backwards) view in main toolbar and the
second(count backwards) Eagle NAND Program to get into the next menu.
41
Follow these instructions to load the appropriate file
Load suffix
file .txt
When toolbar shows Success .Please reset power. That means burning finished (Notice Although the hint shows
42
complete but it may not be burning completed, wait for 5 minutes to shut off power. If U disk cannot be used
for burning, boot file should be burning again until U disk can be used for upgrading. .
3, CI+KEY burning
i.CI + is certain TV operators encrypted to digital TV channels, need to watch the event on TV after decrypting,
if TV software upgraded , must re- burn ci + key, otherwise the
ii.client will not normally watch encrypted program .
iii.All parts on main board with CI socket must burn ci + key, if any question, please contact the engineer .
iv.ci + key running reference to "MSD6308 program ci + key count file modification ", "MSD6308 ci + key burn".
43
History Rev
Author
44
12V
45
AV-IN
VGA
MSD6308
AUDIO-OUT
USB
RF
- +
46
5V
12V
47
video NAND & CI & TS & Front End POWER&GND
PHY
VGA
YPBPR
TS IN
USB
SCART
CVBS
PCM
TS OUT
VIF
MCP
MIU0
NAND
HDMI & Audio GPIO & LVDS
PWM
SAR
LVDS
SPI
HDMI A
Analog Audio
HDMI C
GPIO
TCON
LOCAL DIMMING
I2S
HDMI D
GPIO_PM
SPDIF MHL
Connector
Mode Selection EEPROM
RESET Crystal
48
HDMI3 ( ARC
HDMI1 MHL
ARC DET
49
AV USB2.0 INTERFACE
USB2.0 POWER
LAN
50
AUDIO AMP
AUDIO-OUT
51
Si2151
TUNER POWER
T4292
52
7 5 3 1 7 5 3 1
7 5 3 1 7 5 3 1 8 6 4 2 8 6 4 2
NAND Power
8 6 4 2 8 6 4 2
T4292
53
NAND FLASH