Professional Documents
Culture Documents
DEH-2130R
DEH-2100R X1M/EW
X1M/EW
- This service manual should be used together with the following manual(s):
Model No. Order No. Mech. Module Remarks
CX-958 CRT2423 S8.1 CD Mech. Module:Circuit Description, Mech.Description, Disassembly
CONTENTS
1. SAFETY INFORMATION ............................................2 7. GENERAL INFORMATION .......................................45
2. EXPLODED VIEWS AND PARTS LIST .......................3 7.1 DIAGNOSIS ........................................................45
3. BLOCK DIAGRAM AND SCHEMATIC DIAGRAM .....8 7.1.1 TEST MODE ..............................................45
4. PCB CONNECTION DIAGRAM ................................26 7.1.2 DISASSEMBLY .........................................48
5. ELECTRICAL PARTS LIST ........................................36 7.2 PARTS .................................................................52
6. ADJUSTMENT..........................................................41 7.2.1 IC................................................................52
7.2.2 DISPLAY ....................................................59
7.3 OPERATIONAL FLOW CHART ...........................60
8. OPERATIONS AND SPECIFICATIONS.....................61
1. SAFETY INFORMATION
This service manual is intended for qualified service technicians; it is not meant for the casual do-it-yourselfer.
Qualified technicians have the necessary test equipment and tools, and have been trained to properly and safely repair
complex products such as those covered by this manual.
Improperly performed repairs can adversely affect the safety and reliability of the product and may void the warranty.
If you are not qualified to perform the repair of this product properly and safely; you should not risk trying to do so
and refer the repair to a qualified service technician.
Caution:
1. During repair or tests, minimum distance of 13cm from the focus lens must be kept.
2. During repair or tests, do not view laser beam for 10 seconds or longer.
2. A “CLASS 1 LASER PRODUCT” label is affixed to the 3. The triangular label is attached to the mechanism
bottom of the player. unit frame.
CLASS 1
LASER PRODUCT
Specifications of laser radiation fields to which human access is possible during service.
Wavelength = 800 nanometers
2
Downloaded from www.Manualslib.com manuals search engine
DEH-2130R,2100R
2.1 PACKING 2 3
5 4
10 12
1
11
6
NOTE:
- Parts marked by “*” are generally unavailable because they are not in our Master Spare Parts List.
- Screws adjacent to ∇ mark on the product are used for disassembly.
Mark No. Description Part No. Mark No. Description Part No.
1 Cord Assy CDE6123 * 7-5 Passport CRY1013
2 Screw CBA1002 * 7-6 Warranty Card CRY1157
3 Handle CNC5395 8 Carton See Contrast table(2)
4 Bush CNV3930 9 Contain Box See Contrast table(2)
* 5 Polyethylene Bag E36-615 10 Protector CHP2243
Part No.
Mark No. Symbol and Description DEH-2130R/X1M/EW DEH-2100R/X1M/EW
8 Carton CHG3951 CHG3950
9 Contain Box CHL3951 CHL3950
3
Downloaded from www.Manualslib.com manuals search engine
DEH-2130R,2100R
2.2 EXTERIOR
4
Downloaded from www.Manualslib.com manuals search engine
DEH-2130R,2100R
Part No.
Mark No. Symbol and Description DEH-2130R/X1M/EW DEH-2100R/X1M/EW
42 Panel CNS5340 CNS5188
47 Detach Grille Assy CXB4595 CXB4592
49 Button(Detach) CAC5929 CAC5789
50 Button(+, -) CAC6458 CAC6273
51 Chassis Unit CXB4624 CXB4623
5
Downloaded from www.Manualslib.com manuals search engine
DEH-2130R,2100R
6
Downloaded from www.Manualslib.com manuals search engine
DEH-2130R,2100R
Mark No. Description Part No. Mark No. Description Part No.
1 Control Unit CWX2411 46 •••••
2 Connector(CN802) CKS2192 47 Ball CNR1189
3 Connector(CN801) CKS2193 48 Belt CNT1086
4 Connector(CN701) CKS2773 49 Roller CNV4509
5 Connector(CN101) CKS3486 50 Arm CNV6037
7
Downloaded from www.Manualslib.com manuals search engine
1 2 3 4
DEH-2130R,2100R
3. BLOCK DIAGRAM AND SCHEMATIC DIAGRAM
3.1 BLOCK DIAGRAM
A TUNER AMP ASSY
A Q472 Q474 Q476
LDET
B FM/AM TUNER UNIT
FM FRONT END FM/AM 1ST IF 10.7MHz TMUTE
ANTENNA Q3 T51 Q51 CF51 CF52 CF53 FM MPX
CN402
25 24
27
32 19 Q477
IC 2 PM4008A 6
38 39 42 44 46 63 RDS VDD
34 33 41 44 11 12 13 46
69 DECODER
ANT1 TV
ANT2 TV 22
RF TV
70 FM/AM
FMSD
DI/DO
SDBL
VCC
CE2
CE1
NL1
NL2
CK
SL
25 22 10 14 12 15 16 8 13 2 3 4
Q411
NL1
PDIO
PCE2
PCK
PCE1
SDBW
SL
SD
PD
LOCL
VCC VDD
18 TOP HOME
4
SPINDLE M S801
C MOTOR 12
SOP
HOME
11
CN801 SOM
14
1 COP
CARRIAGE M 13 COM 1 CDLOAD CDLOAD
MOTOR 2 FWD 6 19
10 28 CDEJET EJET
LOP REV 5 20
9 21 CONT CONT
LOM MUTE 11 14
LOADING 3
MOTOR
M
4
CN802
EJTSNS EJTD
3 22 3
1 DSCSNS DINC
23 2
CLAMP CLAMP
VD 21 4
SELECT Q981
SENSE D803 D802 D801 VD
S802 VD 24 1 B.U
2 CLAMP
DISC SENSE +5V REGULATOR
4 IC 701 2
E PHOTO UNIT(S8) VDD
BA05SFP
IN
Q982
1 CD5VON CD5VON
7 18
VDCONT
8
Downloaded from www.Manualslib.com
1 manuals search engine
2 3 4
5 6 7 8
DEH-2130R,2100R
66
TMUTE
61
LDET
CN301
REAR L CH
21 Q346
FM/AM
SYSTEM
CONTROLLER
IC 601(1/2)
2
PE5090A
NL1
6
SD
76
SL
10
SDBW
14
TUNPCE
13
TUNPCK
48
TUNPCE2
12
TUNPDO
PDIO 11
TUNPDI VST
VCK Q353
67 VDT
LOCL
Q903
BACKUP
VDD B.U B.U
FUSE
10A B
2
BACK UP
GND
1
VST/ VCK/ VDT GND
2 POWER AMP
IN1
B.REMOTE
5
B.REM
SYSPW
Q351 MUTE
Q902
asens ACC 4
ACC
bsens
B.U
63
ASENS
Q901
TELIN CELLULAR MUTE
64 7
BSENS CELLULAR MUTE
Q951
SYSTEM
CONTROLLER TELIN
32
IC 601(2/2) C
PE5090A
Q942 Q941
42
SYSPW
31 CDLOAD
34
RR RR
CDEJECT - +
23 CONT BACK FR FR
UP - +
B. FL FL
REM - +
44
80 MUTE RL RL
EJTSNS GND ACC
79
DSCSNS
C KEYBOARD UNIT - +
27
CLAMP
CN601 CN1801
8 20
KYDT 3 3 KYDT
22 9 LCD
VDCONT 4 4 18
DPDT DPDT
RESET
60 1 IC 602 2
RESET VDD
S–80834ANY
VDD
50
5 5 VDD
10 VLCD
41
SWVDD Q650
35
CD5VON
LCD DRIVER
IC 1801 D
PD6293A
KEY MATRIX
22 23
X1801
9
Downloaded from www.Manualslib.com 5manuals search engine 6 7 8
1 2 3 4
DEH-2130R,2100R
3.2 OVERALL CONNECTION DIAGRAM(GUIDE PAGE)
Note: When ordering service parts, be sure to refer to “EXPLODED VIEWS AND PARTS LIST” or “ELECTRICAL PARTS
LIST”.
A
A-a A-b
Large size
SCH diagram
A-a
A-a A-b Guide page
CD:+4.
FM(100%):-15
AM (30%):-26
162
123
272
DSP-201M-S00B
272
123
162
4.194MHz
CSS1047
0R0
R
102
SYSTEM CONTROLLER
R699 0R0
C
KEYBOARD 104
UNIT
D
NOTE :
Symbol indicates a resistor.
No differentiation is made between chip resistors and For resistors and capacitors in the circuit diagrams, their resistance values or
discrete resistors. capacitance values are expressed in codes:
Symbol indicates a capacitor.
No differentiation is made between chip capacitors and Ex. *Resistors
discrete capacitors. Code Practical value
The > mark found on some component parts indicates 123 12k ohms
the importance of the safety factor of the part. 103 10k ohms
Therefore, when replacing, be sure to use parts of
identical designation. *Capacitors
Code Practical value
A
103 0.01µF
101/10 100µF/10V
10
Downloaded from www.Manualslib.com
1 manuals search engine
2 3 4
5 6 7 8
DEH-2130R,2100R
A-b A
CD:+10.1dBs
FM(100%):+6.5dBs
AM (30%):-3dBs
AA TUNER AMP ASSY
4.1dBs
5.5dBs
6dBs
SOURCE SELECTOR/
E.VOL
332/16
CD:+10.1dBs
FM(100%):+6.5dBs
AM (30%):-3dBs
B
>
CEK1136
600µH
Reset
C
(B2)
D CD MECHANISM MODULE
VD REGULATOR
CD:+4.1dBs
102(1/2W)
D
CELLULAR MUTE
RR RR
- +
BACK FR FR
UP - +
B. FL FL
REM - +
GND ACC RL RL
- +
D
A
C
A-a A-b
12
1
1
FM(100%):-15.5dBs
AM (30%):-26dBs
CD:+4.1dBs
FM(100%):-15.5dBs
AM (30%):-26dBs
162
123
272
SOURCE
E.VOL
272
123
DSP-201M-S00B
162
3
3
4
4
4.194MHz
CSS1047
0
0R0
Reset
5
102
2
6
R699 0R0
C
104
KEYBOARD
UNIT
7
7
NOTE :
Symbol indicates a resistor.
No differentiation is made between chip resistors and For resistors and capacitors in the circuit diagrams, their resistance values or
discrete resistors. capacitance values are expressed in codes:
Symbol indicates a capacitor.
D CD MECHANISM MODULE
8
8
A-a 13
DEH-2130R,2100R
A-a A-b
B
C
A
D
B
D
A
14
A-a A-b
1
1
A-b
CD:+10.1dBs
FM(100%):+6.5dBs
AM (30%):-3dBs
.1dBs
5.5dBs
6dBs
SOURCE SELECTOR/
E.VOL
3
3
332/16
CD:+10.1dBs
FM(100%):+6.5dBs
AM (30%):-3dBs
4
4
>
CEK1136
600µH
600µH
Reset
5
(B2)
2
6
VD REGULATOR
7
7
CD:+4.1dBs
102(1/2W)
CELLULAR MUTE
D CD MECHANISM MODULE
RR RR
- +
BACK FR FR
UP - +
B. FL FL
REM - +
GND ACC RL RL
- +
8
8
A-b
A-a A-b
15
DEH-2130R,2100R
C
A
D
1 2 3 4
DEH-2130R,2100R
A A
B FM/AM TUNER UNIT
B
KV1410(23)
KV1410(23)
C
DAN217U
DAN217U
16 B
Downloaded from www.Manualslib.com
1 manuals search engine
2 3 4
5 6 7 8
DEH-2130R,2100R
KV1410(23)
C KEYBOARD UNIT
PD6293A
LCD DRIVER,
KEY CONTROLLER
CAW1559
18
1
C
Downloaded from www.Manualslib.com manuals search engine
2 3 4
5 6 7 8
DEH-2130R,2100R
DISP
CN601
B
PTY TA/AF
A
LOCAL/BSM
DEH-2130R/X1M/EW DEH-2100R/X1M/EW
IL1801-1804 CEL1638(14V 40mA) CEL1547(14V 40mA)
A
D CONTROL UNIT
PICKUP UNIT
(SERVICE)(P8)
CN101
RF-AMP, SE
E PHOTO UNIT(S8)
Q1 CPT230SX-TU Q2 CPT230SX-TU
CN802
SPINDLE MOTOR
M3 CXB2562
CARRIAGE MOTOR
M1 CXB2190
D LOADING MOTOR
CD DRIVER
M2 CXB2195
CN801
20
1
D E
Downloaded from www.Manualslib.com manuals search engine
2
BA05SFP
5V REGULATOR
3 4
5 6 7 8
DEH-2130R,2100R
SWITCHES:
CONTROL UNIT
S801 : HOME SWITCH.....ON-OFF
S802 : CLAMP SWITCH....ON-OFF
The underlined indicates the switch position.
CN701
CN605
A
Note:1. The encircled numbers denote measuring pointes in the circuit diagram.
2. Reference voltage
REFO:2.5V
- Waveforms
1 RFI 0.5V/div. 0.5µs/div. 1 CH1: RFI 1V/div. 0.5ms/div. 1 CH1: RFI 1V/div. 0.5ms/div.
Normal mode: play 2 CH2: MIRR 5V/div. 2 CH2: MIRR 5V/div.
Test mode: Tracking open Normal mode: The defect part
passes 800µm
REFO →
REFO →
REFO →
REFO →
REFO →
REFO → REFO →
REFO →
REFO →
REFO → REFO →
GND →
REFO → REFO →
REFO →
22
Downloaded from www.Manualslib.com manuals search engine
DEH-2130R,2100R
REFO →
REFO →
REFO →
REFO → REFO →
REFO →
REFO →
REFO →
REFO →
GND →
REFO →
REFO → REFO →
REFO →
GND → GND →
GND →
REFO → REFO →
GND → GND →
23
Downloaded from www.Manualslib.com manuals search engine
DEH-2130R,2100R
REFO →
REFO → REFO →
24
Downloaded from www.Manualslib.com manuals search engine
DEH-2130R,2100R
25
Downloaded from www.Manualslib.com manuals search engine
1 2 3 4
DEH-2130R,2100R
A
4.1 TUNER AMP ASSY
NOTE FOR PCB DIAGRAMS
1. The parts mounted on this PCB
include all necessary parts for
several destination.
For further information for
respective destinations, be sure
to check with the schematic dia-
gram.
2. Viewpoint of PCB diagrams
Connector Capacitor
SIDE A
B
C
CN701
D
26 A
Downloaded from www.Manualslib.com
1 manuals search engine
2 3 4
C CN1801
5 6 7 8
DEH-2130R,2100R
A
SIDE A
28 A
Downloaded from www.Manualslib.com
1 manuals search engine
2 3 4
5 6 7 8
DEH-2130R,2100R
SIDE B
SIDE A
A
B
C
FM/AM TUNER UNIT
D
B
30
1
B
Downloaded from www.Manualslib.com manuals search engine
2 3 4
1 2 3 4
DEH-2130R,2100R
SIDE B
C
FM/AM TUNER UNIT
D
B
BAND
AUDIO
A
EJECT
]
'
'
LOCAL/BSM
[
PTY
B
TA/AF
6
5
4
C
3
2
SOURCE/OFF
KEYBOARD UNIT
1
DISP
D
C
+
32 C
Downloaded from www.Manualslib.com
1 manuals search engine
2 3 4
1 2 3 4
DEH-2130R,2100R
SIDE B
A
B
CN601
A
C
KEYBOARD UNIT
D
C
D
A
34
D CONTROL UNIT
1
1
PICKUP UNIT(SERVICE)(P8)
M1 CARRIAGE MOTOR
HOME
M3 SPINDLE MOTOR
3
3
4
4
3
2 D CN802
1
SIDE A
1 2 3 4
DEH-2130R,2100R
SIDE B
CLAMP
B
CONTROL UNIT
C
D
36
Downloaded from www.Manualslib.com manuals search engine
DEH-2130R,2100R
=====Circuit Symbol and No.===Part Name Part No. =====Circuit Symbol and No.===Part Name Part No.
--- ------ ------------------------------------------ ------------------------- --- ------ ------------------------------------------ -------------------------
R 431 RS1/10S153J R 911 RS1/10S122J
R 440 RS1/10S681J R 912 RD1/4PU103J
R 441 RS1/10S102J R 914 RD1/4PU152J
R 442 RS1/10S473J R 916 RS1/10S221J
R 443 RS1/10S681J R 918 RS1/10S1R0J
37
Downloaded from www.Manualslib.com manuals search engine
DEH-2130R,2100R
=====Circuit Symbol and No.===Part Name Part No. =====Circuit Symbol and No.===Part Name Part No.
--- ------ ------------------------------------------ ------------------------- --- ------ ------------------------------------------ -------------------------
C 441 CKSQYB182K50 L 203 Inductor LCTA121J3225
C 442 CKSQYB223K25 L 901 Coil CTC1154
C 462 CKSQYB123K25 L 902 Inductor LCTA3R3J3225
C 463 CKSQYB123K25 L 904 Inductor LCTBR47K1608
C 466 CEJA1R0M50 L 905 Inductor LCTBR47K1608
38
Downloaded from www.Manualslib.com manuals search engine
DEH-2130R,2100R
=====Circuit Symbol and No.===Part Name Part No. =====Circuit Symbol and No.===Part Name Part No.
--- ------ ------------------------------------------ ------------------------- --- ------ ------------------------------------------ -------------------------
R 907 RS1/16S103J C 208 CCSRCH560J50
R 908 RS1/16S681J C 209 CEAL470M6R3
R 909 RS1/16S473J C 210 CKSRYB103K50
R 914 RS1/16S562J C 211 CKSRYB103K50
C 212 CCSRCH101J50
CAPACITORS
C 215 CKSRYB223K25
C 1 CCSQCH5R0C50 C 216 CKSQYB334K16
C 2 CCSRCH5R0C50 C 217 CKSRYB103K50
C 4 CCSRCJ3R0C50 C 219 CKSQYB105K10
C 6 CKSQYB105K10 C 220 CKSRYB104K16
C 8 CKSRYB222K50
C 221 CKSRYB473K16
C 10 CCSRCH220J50 C 222 CKSQYB334K16
C 11 CCSRCH150J50 C 223 CKSQYB474K16
C 12 CCSRCH8R0D50 C 224 CKSRYB104K16
C 14 CCSRCJ3R0C50 C 225 CKSRYB272K50
C 15 CKSRYB103K50
C 226 CKSRYB682K25
C 16 CKSRYB222K50 C 902 CCSRCH270J50
C 17 CKSRYB222K50 C 904 CKSRYB223K25
C 18 CCSRCJ3R0C50 C 905 CKSRYB103K50
C 19 CKSRYB103K50 C 906 CCSRTH100D50
C 20 CKSRYB103K50
C 907 CCSRTH150J50
C 21 CKSRYB103K50 C 909 CCSRTH100D50
C 24 CKSQYB334K16 C 910 CKSRYB332K50
C 31 CKSRYB222K50 C 912 CKSQYB474K16
C 32 CCSRCH470J50 C 913 CKSRYB223K25
C 35 CKSRYB103K50
C 914 CKSRYB682K25
C 51 CKSRYB103K50 C 915 CKSQYB223K25
C 52 CKSRYB473K16 C 916 CKSQYB474K16
C 53 CCSRCK2R0C50 C 917 CKSYB475K10
C 54 CKSRYB103K50 C 918 CKSRYB223K25
C 55 CKSRYB104K16
C 919 CKSQYB225K10
C 56 CKSRYB104K16 C 920 CCSRCH270J50
C 58 CKSQYB224K16 C 921 CCSRCH270J50
C 59 CKSRYB223K25 C 922 CKSYB105K16
C 60 CKSRYB104K16 C 923 CKSRYB103K50
C 101 CEALNP100M10
Unit Number : CWM6779(DEH-2130R)
C
C
102
103
CCSRCH151J50
CKSRYB473K16
C : CWM6778(DEH-2100R)
C 105 CKSRYB682K25 Unit Name : Keyboard Unit
C 106 CEAL2R2M50
C 107 CKSRYB103K50 MISCELLANEOUS
C 108 CKSQYB474K16 IC 1801 IC PD6293A
C 109 CKSQYB474K16 D 1801 Diode MA152WK
C 110 CKSRYB104K16 D 1802 Diode MA152WA
C 111 CKSRYB104K16 X 1801 Ceramic Resonator 4.97MHz CSS1422
C 112 CKSRYB104K16 IL 1801 Lamp 14V 40mA(DEH-2130R) CEL1638
39
Downloaded from www.Manualslib.com manuals search engine
DEH-2130R,2100R
=====Circuit Symbol and No.===Part Name Part No. =====Circuit Symbol and No.===Part Name Part No.
--- ------ ------------------------------------------ ------------------------- --- ------ ------------------------------------------ -------------------------
Unit Number : CWX2411 C 220 CCSRCH510J50
D Unit Name : Control Unit C
C
221
222
CKSRYB682K25
CEV220M6R3
C 223 CKSRYB103K25
MISCELLANEOUS C 224 CKSRYB224K10
IC 201 IC UPD63711GC C 301 CEV101M10
IC 301 IC BA5985FM C 603 CCSQSL152J50
IC 701 IC BA05SFP C 604 CCSQSL152J50
Q 101 Transistor 2SB1132 C 702 10µF/10V CCH1349
D 801 LED CL200IRX C 703 CKSQYB334K16
D 802 LED CL200IRX
Unit Number :
X
S
201
801
Ceramic Oscillator 16.934MHz
Spring Switch(HOME)
CSS1456
CSN1051 E Unit Name : Photo Unit(S8)
S 802 Spring Switch(CLAMP) CSN1052
Q 1 Photo-transistor CPT230SX-TU
RESISTORS Q 2 Photo-transistor CPT230SX-TU
R 302 RS1/16S153J
R 303 RS1/16S103J
R 501 RS1/16S102J
R 502 RA4C681J
R 601 RS1/16S102J
R 602 RS1/16S102J
R 605 RS1/16S0R0J
R 606 RS1/16S0R0J
R 801 RS1/8S751J
R 803 RS1/8S751J
R 902 RS1/16S0R0J
R 906 RS1/16S0R0J
CAPACITORS
C 101 CCSRCH102J25
C 102 CKSRYB104K16
C 103 CEV101M6R3
C 104 CEV470M6R3
C 105 CKSQYB334K16
C 106 CKSQYB334K16
C 107 CKSQYB334K16
C 201 CKSRYB104K16
C 202 CKSRYB471K50
C 203 CKSRYB104K16
C 205 CEV101M6R3
C 206 CKSRYB104K16
C 207 CKSRYB104K16
C 208 CKSRYB104K16
C 209 CKSRYB104K16
C 210 CKSRYB332K50
C 211 CKSRYB104K16
C 212 CKSRYB104K16
C 213 CKSRYB392K50
C 214 CKSRYB104K16
C 215 CKSRYB104K16
C 216 CCSRCJ3R0C50
C 217 CCSRCH270J50
C 218 CKSRYB104K16
C 219 CCSRCH181J50
40
Downloaded from www.Manualslib.com manuals search engine
DEH-2130R,2100R
6. ADJUSTMENT
6.1 CD ADJUSTMENT
1) Precautions 2) Test Mode
• This unit uses a single power supply (+5V) for the reg- This mode is used for adjusting the CD mechanism
ulator. The signal reference potential, therefore, is module of the device.
connected to REFO(approx. 2.5V) instead of GND.
If REFO and GND are connected to each other by mis- • Test mode starting procedure
take during adjustments, not only will it be impossi- Reset while pressing the 4 and 6 keys together.
ble to measure the potential correctly, but the servo
will malfunction and a severe shock will be applied to • Test mode cancellation
the pick-up. To avoid this, take special note of the fol- Switch ACC, back-up OFF.
lowing.
Do not connect the negative probe of the measuring • After pressing the EJECT key, do not press any other
equipment to REFO and GND together. It is especially key until the disk is completely ejected.
important not to connect the channel 1 negative
probe of the oscilloscope to REFO with the channel 2 • If the ] or [ key is pressed while focus search is in
negative probe connected to GND. progress, immediately turn the power off (otherwise
Since the frame of the measuring instrument is usual- the actuator may be damaged due to adhesion of the
ly at the same potential as the negative probe, change lenses).
the frame of the measuring instrument to floating sta-
tus. • Jump operation of TRs other than 100TR continues
If by accident REFO comes in contact with GND, after releasing the key. CRG move and 100TR jump
immediately switch the regulator or power OFF. operations are brought into the “Tracking close” sta-
tus when the key is released.
• Always make sure the regulator is OFF when connect-
ing and disconnecting the various filters and wiring • Powering Off/On resets the jump mode to “1TR”, and
required for measurements. the automatic adjustment value to the initial value.
41
Downloaded from www.Manualslib.com manuals search engine
DEH-2130R,2100R
- Flow Chart
4 6
Test Mode In
Reset
Select CD SOURCE
BAND 3 6
Power ON
(Adjustment for T.Offset)
Power ON
TRK MIN SEC
(Not adjustment for T.Offset)
Display 00 00 00 TRK MIN SEC
Display 99 99 99
Power OFF
BAND 3 6 1 ] [ 2
Display
91 91 91 Display 0x 0x 0x 00 00 00 00 00 00 00 00 00
or or or
TRK MIN SEC TRK MIN SEC TRK MIN SEC
99 99 99 99 99 99 99 99 99
Power OFF
BAND 1 6 3 ] [ 2
T.Close and
F,T AGC and T. Close and RF AGC Coefficient Display/ CRG+ CRG- T.Balance
RF AGC and Fit Servo Rough Servo and RF AGC Adjustment
Fit Servo TRK MIN SEC TRK MIN SEC
Display 8x 8x 8x 8x 8x 8x
or or
TRK MIN SEC TRK MIN SEC
9x 9x 9x 9x 9x 9x
Tracking
Power OFF Open
BAND 1 3 6 ] [ 2
*4 *5 *6 CRG-/TR Jump- *6
F, T, RF AGC/ F, T AGC and CRG/TR Jump NO. CRG+/TR Jump+ *7
F.Bias Display Select RF AGC Select TRK MIN SEC
Power OFF
Display
8x 8x 8x
or
BAND TRK MIN SEC
2
9x 9x 9x
Tracking
Open
TRK MIN SEC
Display 8x 8x 8x
or
TRK MIN SEC
9x 9x 9x
42
Downloaded from www.Manualslib.com manuals search engine
DEH-2130R,2100R
• Purpose :
To check that the grating is within an acceptable range when the PU unit is changed.
• Symptoms of Mal-adjustment :
If the grating is off by a large amount symptoms such as being unable to close tracking, being unable to perform
track search operations, or taking a long time for track searching.
• Method :
• Measuring Equipment • Oscilloscope, Two L.P.F.
• Measuring Points • E, F, REFOUT
• Disc • ABEX TCD-784
• Mode • TEST MODE
CONTROL UNIT
E
F L.P.F.
Xch Ych
E 100kΩ
Oscilloscope
REFO 390pF
F 100kΩ
390pF
REFO REFO
L.P.F.
• Checking Procedure
1. In test mode, load the disc and switch the 5V regulator on.
2. Using the ] and [ buttons, move the PU unit to the innermost track.
3. Press key 3 to close focus, the display should read "91". Press key 2 to implement the tracking balance adjust-
ment the display should now read "81". Press key 3 2 times. The display will change, returning to "81" on the
fourth press.
4. As shown in the diagram above, monitor the LPF outputs using the oscilloscope and check that the phase differ-
ence is within 75° . Refer to the photographs supplied to determine the phase angle.
5. If the phase difference is determined to be greater than 75° try changing the PU unit to see if there is any
improvement. If, after trying this a number of times, the grating angle does not become less than 75° then the
mechanism should be judged to be at fault.
• Note
Because of eccentricity in the disc and a slight misalignment of the clamping center the grating waveform may be
seen to "wobble" ( the phase difference changes as the disc rotates). The angle specified above indicates the aver-
age angle.
• Hint
Reloading the disc changes the clamp position and may decrease the "wobble".
43
Downloaded from www.Manualslib.com manuals search engine
DEH-2130R,2100R
0° 30°
45° 60°
75° 90°
44
Downloaded from www.Manualslib.com manuals search engine
DEH-2130R,2100R
7. GENERAL INFORMATION
7.1 DIAGNOSIS
7.1.1 TEST MODE
- Error Messages
If a CD is not operative or stopped during operation due to an error, the error mode is turned on and cause(s) of the
error is indicated with a corresponding number. This arrangement is intended at reducing nonsense calls from the
users and also for facilitating trouble analysis and repair work in servicing.
45
Downloaded from www.Manualslib.com manuals search engine
DEH-2130R,2100R
46
Downloaded from www.Manualslib.com manuals search engine
DEH-2130R,2100R
47
Downloaded from www.Manualslib.com manuals search engine
DEH-2130R,2100R
7.1.2 DISASSEMBLY
- Removing the Upper Case (not shown)
Fig.1
CD Mechanism Module
Cover
- Removing the Tuner Amp Assy
Fig.2
Fig.3
Tuner Amp Assy
48
Downloaded from www.Manualslib.com manuals search engine
DEH-2130R,2100R
B A
Arm A
Arm
B A
49
Downloaded from www.Manualslib.com manuals search engine
DEH-2130R,2100R
A A
50
Downloaded from www.Manualslib.com manuals search engine
DEH-2130R,2100R
A
A
Loading Motor
Pickup Unit
Shaft
51
Downloaded from www.Manualslib.com manuals search engine
DEH-2130R,2100R
7.2 PARTS
7.2.1 IC
- Pin Functions(PE5090A)
Pin No. Pin Name I/O Format Function and Operation
1 MODEL1 I Model select input
2 NL1 I Noise level input
3 NL2DT I Noise level input 2
4 AVSS A/D GND
5 ST I Stereo input
6 SD I SD signal input
7 AREF1 (D/A converter standard voltage)
8 KYDT I Key data input
9 DPDT O C Key data output
10 SDBW I SDBW input
11 TUNPDI I PLL IC data input
12 TUNPDO O C PLL IC data output
13 TUNPCK O C PLL IC clock output
14 TUNPCE O C PLL IC chip enable output
15 CURRQ O C Tuner voltage FIX output
16 XSI I C LSI data input
17 XSO O C LSI data output
18 XSCK O C LSI clock output
19 DRST O C RDS decoder reset output
20 ADPW O C A/D converter power output
21 FM/AM O C FM/AM power select output
22 VDCONT O C VD power control output
23 CONT O C Servo driver power control output
24 XAO O C CD LSI data discernment control signal output
25 XRST O C CD LSI reset output
26 XSTB O C CD LSI strobe output
27 CLAMP I Disc clamp sense input
28 MIRR I Mirror detection input
29 FOK I Focus OK signal input
30 LOCK I Spindle lock detector input
31 CDLOAD O C LOAD motor loading control output
32 TELIN I Cellular mute input
33 VSS GND
34 CDEJECT O LOAD motor eject control output
35 CD5VON O C CD +5V power supply control output
36–39 NC Not used
40 RECIEVE O C RDS decoder receiving output
41 SWVDD O C Grille power supply control output
42 SYSPW O C System power supply control output
43 NC Not used
44 MUTE O C Mute output
45 PEE O C Beep tone output
46 LOCH O C LOCH output
47 RDS57K I 57kHzBP-OUT sense input
48 TUNPCE2 O C EEPROM chip enable output 2
49 NC Not used
50 VCK O C Clock output for electronic volume
51 VDT O C Data output for electronic volume
52 ANTPW O C Antenna power output
53 VST O C Strobe pulse output for electronic volume
54–57 DEQ4-1 O C Direct EQ data output 4-1
58 RDSLK I RDS LK signal input
59 RDT I RDS data input
60 RESET Reset
52
Downloaded from www.Manualslib.com manuals search engine
DEH-2130R,2100R
*PE5090A
80 61
1 60
S-80834ANY
20 41
21 40
1 2 3
OUT VDD VSS
53
Downloaded from www.Manualslib.com manuals search engine
DEH-2130R,2100R
SN761029DL
TONEout-R
BASS-C1-R
BASS-C2-R
REARout-R
FADERin-R
FRNTout-R
BASS-R-R
SWout-R
IN4(+)-R
LOUD-R
IN4(-)-R
TREB-R
VRin-R
ZCin-R
AGND
DATA
IN1-R
IN2-R
IN3-R
DVcc
VCC
STB
CLK
NC
48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25
Isolator
Volume, Treble Bass Fader
Loudness
Gain
Adjust
Gain
Adjust
Volume,
Loudness Treble Bass Fader Power A
Supply
Isolator
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
AVcc
IN1-L
IN2-L
IN3-L
IN4(+)-L
IN4(-)-L
AGND
SWout-L
ZCin-L
LOUD-L
VRin-L
TREB-L
BASS-C1-L
BASS-R-L
BASS-C2-L
TONEout-L
NC
FADERin-L
FRNTout-L
REARout-L
VREFin
AGND
DGND
Ct
PM4009A
54
Downloaded from www.Manualslib.com manuals search engine
DEH-2130R,2100R
BR9010FV
NC 1 8 WC
SK 4 5 DI
*PD6293A
33
48
32 49
17 64
16
55
Downloaded from www.Manualslib.com manuals search engine
DEH-2130R,2100R
56
Downloaded from www.Manualslib.com manuals search engine
DEH-2130R,2100R
1
1
26
21 100
80
50
40 76
61
51
75
41
60
57
Downloaded from www.Manualslib.com manuals search engine
DEH-2130R,2100R
BA5985FM
58
Downloaded from www.Manualslib.com manuals search engine
DEH-2130R,2100R
7.2.2 DISPLAY
- CAW1559
SEGMENT
COMMON
59
Downloaded from www.Manualslib.com manuals search engine
DEH-2130R,2100R
Power ON
VDD=5V
68pin
bsens
66pin
asens
65pin
dsens
63pin
L
ADPW←H
20pin
swvdd←L
41pin
300ms
In case of the above signal, the communication
Source keys with Grille microcomputer may fail.
operative If the time interval is not 300msec, the oscillator
may be defective.
Source ON
YES
SYSPW←H
42pin
60
Downloaded from www.Manualslib.com manuals search engine
DEH-2130R,2100R
61
Downloaded from www.Manualslib.com manuals search engine
Basic Operation
62
To Listen to Music Basic Operation of Tuner
The following explains the initial operations required before you can listen to music. This product’s AF function can be switched ON and OFF. AF should be switched OFF
for normal tuning operations.
Note:
• Loading a disc in this product.
1. Select the desired source (e.g. Tuner). Manual and Seek Tuning
• You can select the tuning method by changing the length of time
DEH-2130R,2100R
Each press of the SOURCE/OFF button selects the desired source in the following order:
Preset Tuning
• You can memorize broadcast stations in buttons 1 through 6 for
easy, one-touch station recall.
Preset station recall 2 seconds or less
Broadcast station preset memory 2 seconds or more
Note:
• Up to 12 FM stations (6 in F1 (FM1) and F2 (FM2)) and 6 MW/LW stations can be
stored in memory.
• You can also use the 5 or ∞ buttons to recall broadcast stations memorized in buttons 1
through 6.
Basic Operation Audio Adjustment
Note:
• If a disc cannot be inserted fully or playback fails, make sure the recorded side is down.
Push the EJECT button and check the disc for damage before reinserting it.
• If a disc is inserted with the recorded side up, it will be ejected automatically after a few
moments.
• If the built-in CD player cannot operate properly, an error message (such as “ERROR-14”)
appears on the display.
63
DEH-2130R,2100R
Audio Adjustment
64
Audio Menu Functions Treble Adjustment (TRE)
The Audio Menu features the following functions. You can adjust a Treble level as desired.
1. Press the AUDIO button and select the Treble mode (TRE) in the Audio
Balance Adjustment (FAD) Menu.
This function allows you to select a Fader/Balance setting that provides ideal listening con-
ditions in all occupied seats. 2. Boost or attenuate the treble
level with the 5/∞
∞ buttons.
1. Press the AUDIO button and select the Fader/Balance mode (FAD) in the
DEH-2130R,2100R
1* 3. Antenna jack
18. Yellow/black
8. Yellow (3*) 9. Yellow (2*) 19. Fuse holder 21. System remote control
Back-up To terminal always supplied
(or accessory) with power regardless of
ignition switch position. 25. Rear speaker 25. Rear speaker
+ +
10. Red (5*) 11. Red (4*)
Accessory To electric terminal con- ≠ ≠
(or back-up) trolled by ignition switch
(12 V DC) ON/OFF.
22. Blue/white (6*) 23. Blue/white (7*) 26. Perform these connections when using
To Auto-antenna relay control terminal. a different amp (sold separately).
(Max. 300 mA 12 V DC.)
12. Black (ground)
To vehicle (metal) body. 14. Speaker leads
White : Front left +
White/black : Front left ≠ 24.
Gray : Front right +
Gray/black : Front right ≠ The pin position of the ISO connector will differ
Green : Rear left + depends on the type of vehicle. Connect 6* and 7*
Green/black : Rear left ≠ when Pin 5 is an antenna control type. In another
Violet : Rear right + type of vehicle, never connect 6* and 7*.
Violet/black : Rear right ≠
65
DEH-2130R,2100R
DEH-2130R,2100R
8.2 SPECIFICATIONS
General FM tuner
Power source .......... 14.4 V DC (10.8 – 15.1 V allowable) Frequency range ...................................... 87.5 – 108 MHz
Grounding system ........................................ Negative type Usable sensitivity
Max. current consumption ...................................... 10.0 A .................. 11 dBf (1.0 µV/75 Ω, mono, S/N: 30 dB)
Dimensions 50 dB quieting sensitivity .... 16 dBf (1.7 µV/75 Ω, mono)
(mounting size) ...... 178 (W) × 50 (H) × 159 (D) mm Signal-to-noise ratio ...................... 70 dB (IEC-A network)
(front face) .............. 188 (W) × 58 (H) × 19 (D) mm Distortion .......................... 0.3% (at 65 dBf, 1 kHz, stereo)
Weight ...................................................................... 1.4 kg Frequency response ...................... 30 – 15,000 Hz (±3 dB)
Stereo separation .......................... 40 dB (at 65 dBf, 1 kHz)
Amplifier
Maximum power output ...................................... 40 W × 4 MW tuner
Continuous power output .................................... 22 W × 4 Frequency range ........................ 531 – 1,602 kHz (9 kHz)
(DIN45324, +B = 14.4 V) Usable sensitivity .............................. 18 µV (S/N: 20 dB)
Load impedance .......................... 4 Ω (4 – 8 Ω allowable) Selectivity .................................................. 50 dB (±9 kHz)
Preout maximum output level/output impedance
................................................................ 2.2 V /1 kΩ LW tuner
Tone controls Frequency range ........................................ 153 – 281 kHz
(Bass) .............................................. ±12 dB (100 Hz) Usable sensitivity .............................. 30 µV (S/N: 20 dB)
(Treble) ............................................ ±12 dB (10 kHz) Selectivity .................................................. 50 dB (±9 kHz)
Loudness contour.......... +10 dB (100 Hz), +7 dB (10 kHz)
(volume: –30 dB)
CD player
System .................................... Compact disc audio system
Usable discs .................................................. Compact disc
Signal format...................... Sampling frequency: 44.1 kHz
Number of quantization bits: 16; linear
Frequency characteristics................ 5 – 20,000 Hz (±1 dB)
Signal-to-noise ratio ........ 94 dB (1 kHz) (IEC-A network)
Dynamic range ............................................ 92 dB (1 kHz)
Number of channels ............................................ 2 (stereo)
Note:
• Specifications and the design are subject to possi-
ble modification without notice due to improve-
ments.