Professional Documents
Culture Documents
Manual
AEC Drafting
State:2/1/2021
Version:2.9.0
neoapps GmbH © 2020 page 2
Contents
Program start / common information ......................................................................................... 4
Material Dependent Hatch..................................................................................................... 5
AEC Drafting tool descriptions ................................................................................................... 6
AEC Spline Dimension .......................................................................................................... 6
AEC Spline Dimension with Sections .................................................................................... 7
AEC Dimension with Extension Line Cut .............................................................................. 8
AEC Grad < > Gon conversion ............................................................................................. 9
AEC Elevated mm ............................................................................................................... 10
AEC Horizontal View and Section Alignment ...................................................................... 10
AEC Chainage 2D ............................................................................................................... 11
The Dialog: ...................................................................................................................... 11
Usage: ............................................................................................................................. 12
AEC Section View with Depth ............................................................................................. 15
The Dialog ....................................................................................................................... 15
Create Section View with Depth ..................................................................................... 16
Select StartPoint and EndPoint on Model in ParentView ............................................... 17
Editing the Section Depth ............................................................................................... 18
Delete the Section Depth ................................................................................................ 19
Delete by Software .......................................................................................................... 19
Delete by deleting “Preview” Sketch ............................................................................... 20
AEC Longitudinal Section.................................................................................................... 21
Along Whole Curve ......................................................................................................... 22
Select Start and Endpoint ............................................................................................... 25
AEC Edit Section Edge Curve ............................................................................................. 26
Introduction ..................................................................................................................... 26
Dialog .............................................................................................................................. 26
How to use: ..................................................................................................................... 27
Set Linewidth................................................................................................................... 27
Edit or Remove Edit ........................................................................................................ 28
Remove ........................................................................................................................... 28
AEC Elevation numbers ...................................................................................................... 29
Flood Level...................................................................................................................... 33
AEC Slope dimension ......................................................................................................... 34
AEC Hatch Line ................................................................................................................... 35
Natural Ground ............................................................................................................... 36
Batter without Border ...................................................................................................... 38
Batter with border ............................................................................................................ 39
Construction Join ............................................................................................................ 40
AEC Hatches (Area filling)................................................................................................... 42
AEC Round Pillars ............................................................................................................... 43
Define Round Pillar ......................................................................................................... 44
Reverse Round Pillar Hatches ........................................................................................ 46
Edit Round Pillar In Region ............................................................................................. 47
Delete Round Pillar Hatches: .......................................................................................... 48
Move, Rotate, Scale the View ......................................................................................... 49
Edit Model Geometry ...................................................................................................... 49
AEC Setting out points ........................................................................................................ 50
AEC Stakeout the Edges..................................................................................................... 52
AEC Attributes ..................................................................................................................... 54
AEC Revision Cloud ............................................................................................................ 57
Introduction ..................................................................................................................... 57
Dialog .............................................................................................................................. 57
How to use ...................................................................................................................... 57
Rectangular Revision Cloud ........................................................................................... 58
Polygonal Revision Cloud ............................................................................................... 60
Circular Revision Cloud .................................................................................................. 61
Edit Revision Cloud ......................................................................................................... 62
Move the Cloud ............................................................................................................... 63
Delete Revision Cloud .................................................................................................... 64
To make the work faster and easier it is possible to use the radial toolbar (Figure 2) and the
context menu (Figure 3) for some objects (dimensions).
The "radial toolbar" shows up with a permanent right lick at the object.
The "context menu" shows up with a single left klick at the object.
Analog to UNIGRAPHICS NX all our dialogs use the middle mouse button as „OK“.
All information's about the configuration file are located at the section "Configuration" and the
preferences for drawing are located at the section "Drafting Preferences".
The Figure 4 shows the settings for the PMI section view, material must be selected for the
pattern definition, then the size, angle and color of the hatching can be defined!
Now it is possible to paste the PMI section view (Figure 5 Section #1). With the toggle Inherit
Crosshatch (settings) the material dependent hatch will be displayed in the section view.
IMPORTANT INFORMATION:
For the AEC Suite, a tool is planned to select the section view(s) and converts the contained
hatchings into the material dependent hatchings.
The construction unit has to be the same unite as the construction unit of the model, if this is
selected wrong the dimension text is displayed in the wrong format.
Now you can select edges out of the model, enter the desired text height and the length of the
dimension arrow.
Within the option „edit existing spline dimension“, you can only change the length of the
dimension arrow. All other properties can be changed with native NX functions.
The spline dimension is completely associative to the model. The shown dimension is the
projected length of the select edge/curve. Currently only the top view is supported.
Figure 11: Fully loaded Dialog AEC Spline Dimension with Sections
Now it is possible to select the edges from the Model and set every inputs as needed.
If "Create overall dimension" option is turned on, an overall dimension about all selected
edges is produced, which also includes gaps automatically.
Select points out of the model as boundary objects. The Selected Points has to be on the
selected Spline.
The Sections are all created on one side, with a toggle it is possible to switch the Sections to
the opposite side and the same applies for the text rotation, with a toggle it is possible to
rotate the text about 180°.
NOTE: Please make sure whether NX creates an associative or non-associative point (status
bar). The offset distance between the dimension text and dimension line can be set in the
configuration file.
This tool cuts the extension lines depending on the font size and is configurable within
AECDrafting.xml.
Selectable:
1.) Dimensions with 2 extension lines (radial dimension excluded).
2.) Spline Dimension
NOTE: A dimension that has been created between two 2D centerlines is not currently
supported.
This Application is only for the use in Drafting. It converts the text from an angular dimension
from grad to gon and also back from gon to grad.
The Figure 15 shows the dialog which is used to ask in what unit should be converted.
The Figure 16 shows the selection dialog for the angular dimension, this dialog opens when
user has chosen the unit for the conversion.
AEC Elevated mm
If a dimension has at least 3 decimals, elevated mm elevates the 3rd decimal and truncates
the other decimals. If the 3 decimal is a 0, it is not displayed.
This function aligns views and sections to the x-axis of the current drawing sheet.
First set the direction for the rotation. With the two to be selected points, the vector is
determined, which is used to be horizontally aligned on the drawing sheet.
AEC Chainage 2D
Die AEC Stationierung DWG ist eine Applikation zum übertragen der AEC
Stationierungsdaten vom 3D Model in eine Zeichnungsansicht. Die Übertragenen Objekte
(Lienen, Texte) können dann individuell angepasst werden.
The Dialog:
The Dialog contains two groups:
- "Selection"
- In case of Section View "Chainage Line Length"
- "Create or Update"
Group "Selection"
The first group (Figure 22) "Selection" includes all necessary selections.
The second group (Figure 22) is only in case of a section view visible and it is to set the line
length above and below the chainage position.
The third group (Figure 22) "Create or Update" shows the buttons to create and to update the
chainage in drafting.
Usage:
The following text describes how the application is to use.
Select Component:
- The "Reference Set" must be set to "CHAINGE". Then the objects can be picked from
the software.
- If it is an assembly the selection scope must be set to "Entire Assembly". With that
setting it is possible to select a dingle component.
Select View:
- It has to be a "Base View" or a "Section View" (only longitudinal sections of the
building are allowed) no Detail View.
Create:
- A klick at the "Create" button perform the creation of the 2D chainage. The Figure 23
shows an example.
Customizing in View:
- Text:
Select a text to move it (multiple selection is also possible). It works simple by drag and
drop. With a double klick on a text, the text itself can be changed, like a NX native Hint.
- Line:
The format properties of the lines can be changed by "Edit Display" (Ctrl + J) after
selecting (also multiple selections) the line. In order to change the length of the line the
view has to be expanded (position and direction can also be changed, but should not be
made during the stationing).
To do this, right-click on the view frame and select the "Expand" in the right klick menu
(third group) as shown in Figure 25.
As shown in Figure 26, the length of the line can be changed at the ball (end point) or the
arrow head (start point).
The Figure 27 shows an adapted (customized) version of the Chainage 2D in the drawing
view.
Furthermore, the lines or texts of the chainage can also be formatted using the groups
created in the part navigator. It is so easy and fast to edit the display settings of the line and
text.
In order to update the chainage lines and the chainage texts, the component and the view has
to be selected again, then the Chainage can be restored by clicking the "Update" button.
IMPORTANT: If you want to set back to the state from the 3D model, all individual
adaptations in the drawing will be lost! To ensure that this is also desired, a query can be
seen in Figure 29.
If this query is answered with "Yes", the actual 2D Chainage is deleted and the new 2D
Chainage will be created with the data from the 3D model.
You can delete the stationing elements either by deleting each individual line or text, as well
as by deleting the respective group (see Figure 28).
AEC Section View with Depth is a tool designed for getting the Break-Out View in a Section
View by a user defined depth. With a few clicks, users can see the Break-Out View of this
“Depth Cut”. For showing the “Depth Cut” area, a preview Sketch will be created on a
configurable Layer which is set by user during the process. The Cut - Line is fully editable,
which enables a reliable and operational practicability. User can edit the Cut - Line at any
time, the Section View will be updated as long as the Cut - Line is modified
The Dialog
The Dialog contains two Parts, “Create Section View with Depth” and “Delete Section View
with Depth”, as showed in Figure 31.
Press the Button "Delete section with Depth" and select the section view to delete or select
the sketch in the Part Navigator and delete it.
First select the section view and then the complete dialog is available
After selecting the section view, select start- and endpoint in the associated base view. To
define the depth, change the value (Section Depth [m]) in the Dialog
Important: Start and end points must be set to a drafting curve (spline) for the "Point on
curve" catch point, for example if you select a cutting line to define the point, the depth cannot
be determined and the depth cut it does not work.
As shown in Figure 35, a “Preview of Section Depth” will be created in Parent View. This
“preview” is actually a Sketch on Sheet named after the selected Section View. The “Preview”
will be updated every time you reset StartPoint and EndPoint. Then click “OK” or “Apply”
You will get the result of Section Depth as shown in
First, activate the Sketch from Part Navigator (Hook and DoubleClick in Part Navigaor).
After the activation, you can edit the Sketch by drag “End-Cut-Line”.
Right after your drag of end line is done, the Section View will be updated automatically.
You can repeat this step at any time you want. And the Section View will always be up–to–
date.
To hide Sketch and the dimension remove the hook in the part navigator and deactivate the
layer you set before in “AECDraftingConfig.xml” by Layer Settings(Ctrl + L).
Delete by Software
Select “Delete Depth Section”.
Figure 45: Delete the Section with Depth by deleting the Sketch
Set the distance between the intermediate sections. This distance will determinate the
amount of sections in the curve, that will be cut.
Set the tolerance and determinate the tolerance for the points which creates a section. If the
longitudinal section is not possible to set, it is recommendable to prove with a different
tolerance.
Select the direction vector for the new section. Up/down set the section in horizontal, left/right
set the section in vertical.
Result:
Note: When using with maximum number of sections, it can lead to a Performance reduction.
Introduction
AEC Edit Section Edge Curve allows you to edit all Section Edge Curves in a Section View.
You can select the Linewidth as you want, and apply to all Section Edge Curves in the
selected Section View.
Dialog
Main dialog is showed in Figure 60.
How to use:
- Select View
The View Selection is set to “Section View Only” and “Single”, so only Section View is
editable in this case, and one edition at one time. After your selection of a Section View, all
Section Edge Curves in the View will be highlighted. Those Curves are the ones to be edited
in the following process.
Set Linewidth
Remove
This button creates/defines elevation number points in the modeling (3D) und sets the
corresponding elevation number symbol in the drafting (2D).
To create a setting out points table, select first an AEC Coordinatesystem. (See chapter ‘AEC
Coordinatesystem’ for more details).
Consequently the settings for the symbol of the elevation number are set.
After the user sets all desired properties, he can start with the selection of the points on the
drawing.
This dialog allows the selection of points which were set in the modeling (3D) before.
If the option „allow only elevation points“ is selected, the selected points will be filtered right
after selection. If you select another point while this option is active, it will be ignored and the
selection will be deleted automatically.
If the validation is positive, the previous selected symbol is placed on the drawing.
➔ Option ACTIV:
Only existing elevation points from the model can be selected. Furthermore, the
tolerance settings for XYZ are available here.
Within the XY Tolerance only one symbol is created, and only used the heights which
exist outside the Z-tolerance.
The selected points are immediately upon selection, according to the set "Only
Elevation-Points allowed" filtered. If this option is set, and it also points are selected
which are not Elevation-Points, these selected points for creating the elevations
symbols are not considered and the selection is automatically deleted.
The review should be positive, then immediately the preset icon on the drawing is
issued.
➔ Option INACTIV:
Any points can be selected. For example, an end-point of an edge.
Note: Please note native NX messages in the status bar (Associative - or non-
associative selected item)
Example:
Scope of application example: In some cases it is necessary that the height is not reflecting
the reference to the sea level, but e.q. the height of a building. In this case you have to use
relative elevation number points on the drawing.
Further relative elevation numbers can be now defined on the construction. As long as you
stay in this dialog relative elevation numbers will be created. To create “normal” elevation
numbers on the drawing, you must close and reopen the dialog.
TOP-View symbol
The symbols for the section views can also be rotated by 180 degrees, so that the “arrow”
points to the top side. This orientation is set by the option direction.
To create a symbol without underline, the option “suppress underline of symbol” has to be set.
Furthermore, you find options for the textsize. The symbols for the text size 2.5 are smaller
than the symbols for the text size 3.5.
With the scale option you can scale any symbol as you like. E.q.: If you enter a scale of 0.5
the whole symbol will be half size, also the text size of the elevation value.
Flood Level
In addition to the high points, a symbol for the flood level mark can now also be set.
The dialog in Figure 74 shows the selection of the symbol and Figure 73 shows the design of
the symbol.
Select view/section.
After the selection of a view or section, all options to create a hatch are available.
Natural Ground
Thermal Insulation
Construction Join
Demolition Line
Configuration Settings:
How to set the AEC hatches in NX hatch dialog is shown in Figure 88, the hatching can now
be configured and then inserted to fill an area.
The aim of AEC Round Pillar Hatches is to create a vivid image of a Round Pillar in Drafting.
By using this tool, customers can easily distinguish a Round Pillar from other bodies. The
Round Pillar Hatches is fully associated to view and model. Any modification on model will
cause an auto-update to the View, and Hatches are associative to View in terms of Scale,
Rotation, Move and Update.
Dialog
How to use:
Note: Available “Round Pillar” are shown as following. So you can create Round Pillar on
these Bodies.
This software has taken these “Round Pillar” Bodies into consideration.
- Cylinder
- Variational Sweep
- Extrude
- Pipe (Tube)
- Swept
- Sweep
- Cone
As is shown in the graph above, there are two Hatches presented on wrong side. So, click
“Edit Hatches” button, select these two Bodies with wrong side Hatches. Then click “Reverse
Direction” button.
For all changes in Drafting, like move, rotate or scale the view, the Hatch will be associative a
stay at the correct position.
Delete By Dialog
Important Note:
There is one exception where the hatching fails. This case is depicted in figure 88 (Pillar with
angel to trim line). Left shows the top view with the trim line, in the middle of the figure you
see the trimmed version and on the right the zoomed result is shown. In this case the right
contour line is not the section of the ellipse but on the hidden circle. Consequently, the anchor
points on the ellipse are not detected which results in a lapse. We suggest to place the
section that the contours join the ellipse.
Drafting (2D)
To create the setting out points table you have to select a view or section first:
Construction-unit:
MILLIMETER 1m:1000mm
METER 1m:1mm
Information: Only existing points can be selected, which were created in the model before,
otherwise the table entries and setting out points are not associative.
After all desired points are selected and the position for the setting out points table is set, the
dialog gets confirmed with the OK button and the tabular note and the setting out point
symbols get created.
The setting out points symbols are associative to the selected point.
If the point gets moved in the model, also the relating symbol moves and the relating value in
the tabular note is updated.
If a point gets deleted in the model, also the symbol is deleted, and the related table entry is
removed.
Information: In the AECDrafting configuration file, you can set the text property for the text
above the table, the text in the first row and the text in the other rows in the table.
The text at the symbol can be moved. The symbol itself cannot be moved.
Information: The text property of the text of the symbol can be set in the AECDrafting
configuration file.
To start the software in the drawing area, an AEC coordinate system must first be selected
(for more details see section AEC coordinate system - Drafting).
Information: The creation of the stakeout edges is only working with elevation points, which
were created in the model with chainage or which were created afterwards with chainage
parameters. Points, which were defined as elevation points manually, do not have any
relation to a chainage and cannot be attached to them.
To create the stakeout edges table you have to select a view or a section first
Construction-unit:
MILLIMETER 1m:1000mm
METER 1m:1mm
After confirming the “Add new stakeout edge” button, a new entry field is available.
The settings for stakeout edges can be changed any time afterwards. Therefore, select the
desired list entry. Afterwards you can enter a new name (Enter confirms), select a new edge
or change the position of the note on drawing. The note on the old position is deleted
automatically.
If no elevation points exist (no intersection of edge/station line) on a chainage with its selected
stakeout edges, the related field will be kept empty.
The style of the note text and the style of the tabular note can be configured in
AECDrafting.xml.
If an elevation point is moved or deleted in the model, the table is not updated automatically.
The user must select the tabular note and have to press the “Update” button.
AEC Attributes
Information:
The application must be ‘Drawing’, otherwise an error message will be shown.
After all defined attributes (see configuration file) are checked, the whole dialog is available:
After all desired inputs/settings are confirmed and the ok/apply button is activated, the
component description will be created in the drawing at the selected position.
You don’t can edit the content of the part denotation native. Start the AEC Attributes tool and
select the existing part denotation to edit.
You can update the part denotation when you update the associated view.
<Patter_1>
Free text: Text1
$ATTRIBUTE_TITLE$
<Patter_2>
Free text: Text2
$ATTRIBUTE_TITLE$
Introduction
AEC Revision Cloud is a tool which allows you to drawing Revision Cloud in Siemens NX.
The Revision Cloud is created not only for drawing some nice cloud in Drafting, but also for
drawing attention to the user. This will help you to increase your productivity.
Dialog
The dialog of this tool contains 2 groups.
• Selection of View
• Definition of Revision Cloud
How to use
1. Select View
After you select the view, a default name depending on the selected View will be set to
“Revision Cloud Name” block as shown above (Selected View: Top@1). And later after Apply
or Ok, the associativity of your Revision Cloud will be set to the View you selected.
As is shown in the graph above, this two points selection will create a vertical & horizontal
Rectangle.
Result as you seen above. The Revision Cloud is set to RED, but you need to turn off
“Monochrome” first. Go to Part Navigator, right click on Drawing, uncheck Monochrome.
As is shown in the graph above, set cloud Points as you want. If the distance between two
points is bigger than the maximum diameter you set. The software will create several points in
between to enable the creation of Revision Cloud.
As is shown in the graph above, select two Points for center and radius, this will create a
circular Revision Cloud.
• Delete directly
• Delete Permanently
The AEC North Arrow tool adds a north arrow symbol to a selected view. This symbol is
aligned on the Y axis of a previously selected AEC coordinate system.
View/Section selction:
First the view into which the symbol should come must be selected.
Insert Position:
When a view is selected, use the cursor to select a position within the view frame of the
selected view as symbol position.
When the position is specified you can insert the symbol into the view by clicking on OK.
The symbol is placed in the view with a customizable scale and angle. The size can be
changed via the symbol scale and the angle via the symbol angle. An angle change should
not be made manually because the dependent AEC coordinate system has set the north
direction.
Configuration
AECDrafting.xml
Some of the AECDrafting tools have the possibility to be configured. You find those
configurations in the application directory within the file AECDrafting.xml. The same file also
resists in the udo directory. Changes at those files only have to be done by administrators.
Drafting Preferences
In the AECDrafting Toolbar you will find some actions to quickly switch NX drafting
preferences.
Sets the annotation style to filled arrow with 2.5 Text size and the unit to meter
Sets the annotation style to filled arrow with 3.5 Text size and the unit to meter
Sets the annotation style to filled arrow with 2.5 Text size and the unit to millimeter
Sets the annotation style to filled arrow with 3.5 Text size and the unit to millimeter
Sets the annotation style to cross with 2.5 Text size and the unit to meter
Sets the annotation style to cross with 3.5 Text size and the unit to meter
Sets the annotation style to cross with 2.5 Text size and the unit to millimeter
Sets the annotation style to cross with 3.5 Text size and the unit to millimeter
This action requires one or more selected view labels. The selected view labels text size is
set to 5.0 and the text is underlined.
This action requires one or more selected view labels. The selected view labels text size is
set to 7.0 and the text is underlined.
Sets the text size to 2.0 mm and the length of the arrowhead to 2.0 mm. The arrowhead is
filled. The line font of the text will be set to thin.
Sets the text size to 2.5 mm and the length of the arrowhead to 2.5 mm. The arrowhead is
filled. The line font of the text will be set to thin.
Sets the text size to 3.5 mm and the length of the arrowhead to 3.0 mm. The arrowhead is
filled. The line font of the text will be set to normal.
Sets the text size to 5.0 mm and the length of the arrowhead to 4.0 mm. The arrowhead is
filled. The line font of the text will be set to normal.
Sets the text size to 7.0 mm and the length of the arrowhead to 5.0 mm. The arrowhead is
filled. The line font of the text will be set to thick.
List of Figures
Figure 1: Ribbon Bar AEC Drafting ........................................................................................... 4
Figure 2: Radial Toolbar ............................................................................................................ 4
Figure 3: context menu .............................................................................................................. 4
Figure 4: PMI Section View – Material dependent Hatch .......................................................... 5
Figure 5: Paste PMI Section View (Settings) ............................................................................ 5
Figure 6: AEC Spline Dimension Icon ....................................................................................... 6
Figure 7: Dialog AEC Spline Dimension .................................................................................... 6
Figure 8: Fully loaded Dialog AEC Spline Dimension ............................................................... 6
Figure 9: AEC Spline Dimension with Sections Icon ................................................................. 7
Figure 10: Dialog AEC Spline Dimension with Sections ........................................................... 7
Figure 11: Fully loaded Dialog AEC Spline Dimension with Sections ....................................... 7
Figure 12: AEC Dimension with Extension Line Cut Icon ......................................................... 8
Figure 13: Dialog AEC Dimension with Extension Line Cut ...................................................... 8
Figure 14: AEC Elevated mm .................................................................................................... 9
Figure 15: Start dialog - Grad<>Gon ......................................................................................... 9
Figure 16: Dialog for object selection ........................................................................................ 9
Figure 17: AEC Elevated mm .................................................................................................. 10
Figure 18: Dialog AEC Elevated mm ....................................................................................... 10
Figure 19: AEC Horizontal View and Section Alignment Icon ................................................. 10
Figure 20: Dialog AEC Horizontal View and Section Alignment ............................................. 10
Figure 21: Symbol AEC Chainage 2D ..................................................................................... 11
Figure 22: AEC Chainage 2D – Dialog .................................................................................... 11
Figure 23: 2D Chainage after creation in View ........................................................................ 12
Figure 24: Chainage Longitudinal Section .............................................................................. 12
Figure 25: View Expand .......................................................................................................... 13
Figure 26: Change Line Length ............................................................................................... 13
Figure 27: Customize Chainage 2D ........................................................................................ 13
Figure 28: Groups from Chainage in the Part Navigator ......................................................... 13
Figure 29: Querry Update 2D Chainage .................................................................................. 14
Figure 30: AEC Section View with Depth Icon ........................................................................ 15
Figure 31: Dialog 1 AEC Section View with Depth .................................................................. 15
Figure 32: Dialog 2 AEC Section View with Depth .................................................................. 15
Figure 33: Dialog 3 AEC Section View with Depth .................................................................. 15
Figure 34: Select the View ....................................................................................................... 16
Figure 35: Preview of Section Depth ....................................................................................... 17
Figure 36: Result Section Depth .............................................................................................. 17
Figure 37: Activate Sketch in Part Navigator. .......................................................................... 18
Figure 38: Edit Sketch ............................................................................................................. 18
Figure 39: Update Section View .............................................................................................. 18
Figure 40: Up to Date Section View ........................................................................................ 19
Figure 41: Layer ....................................................................................................................... 19
Figure 42: Dialog Delete Depth Section .................................................................................. 19
Figure 43: Select the associate Section View ......................................................................... 20
Figure 44: The Section View will be restored to original state ................................................ 20
Figure 45: Delete the Section with Depth by deleting the Sketch ........................................... 20
Figure 46: Drawing Update ...................................................................................................... 20
Figure 47: Symbol AEC Longitudinal Section ......................................................................... 21
Figure 48: Dialog 1 AEC Longitudinal Section ........................................................................ 21
Figure 49: Dialog 2 AEC Longitudinal Section ........................................................................ 21
Figure 50: EX 1 - Longitudinal Section .................................................................................... 22
Figure 51: EX 2 - Longitudinal Section .................................................................................... 22
Figure 52: EX 3 - Longitudinal Section .................................................................................... 23
Figure 53: EX 4 - Longitudinal Section .................................................................................... 23
Figure 54: EX 5 - Longitudinal Section .................................................................................... 23
Figure 55: EX 6 - Longitudinal Section .................................................................................... 24
Figure 56: RESULT - Longitudinal Section ............................................................................. 24
Figure 57: Start Point on guide spline ..................................................................................... 25
Figure 58: End Point on guide spline....................................................................................... 25