Professional Documents
Culture Documents
4G Basics OptimizationConcept - Vishwadeep
4G Basics OptimizationConcept - Vishwadeep
EnodeB-EvolvednodeB: Responsble for AC,LC,RRM,HO,Radio bearer control,scheduler(Dynamic Resource Allocation ),IP Header Compression/ de- UE-enodeb
compression
EPC(SAE)+EUTRAN(LTE)=EPS(Evolved Packet system), No CS component UE-SGW
SRB0 RRC REESTABLISHMENT UE-PDN
SRB1 RRC+NAS
SRB2 ONLY NAS
Architecture
SGW
PGW
For Random Access attempts; SIBs indicates the PRACH configuration (duration; frequency; repetition; number of preambles - max. 64)
Radio bearer
ERAB
PDP connection/Session
Capacity = No of bits transferred in a sub frame / Duration of the Subframe(i.e 1milli sec)
Total number of Resource block in a slot = Bandwidth / (Each subcarrier bandwidth * no of subcarriers in a Resource Block)
Bandwidth = 5Mhz
Each sub carrier width = 15Khz
No of sub carriers in a Resource Block = 12 (As 12 Subcarrier is 1 Resource block )
Calculation of total no of resource blocks in 5MHz Bandwidth
so Resource block in one slot = 5 Mhz / (15 KHz *12 ) = 27.77 (But used RBs will be 25 for 5MHz bandwidth)
so Total Resource block in one subframe = 2 * Resource blocks in a slot = 50 RBs
Calculation of total no of symbols/Resource Elements in 5MHz Bandwidth
Total no of symbols / Resource Elements = 50 * no of symbols(REs) in a Resource block
No of symbols(REs) in a resource block = 12 subcarrier * 7 symbols = 84 symbols(REs)
Total symbols(REs ) in 50 Resource blocks = 50 * 84 = 4200 Resource Elements.
****Calculation of total no of bits sent in 5MHz Bandwidth in one subframe ****
In one symbol we can send no of bits at a time which depends on the modulation scheme (like BPSK,QPSK ,64QAM
BPSK - 1 bit,QPSK - 2 bit ,64 QAM - 6bits in a Symbol/ Resource elements
We will consider QPSK Scheme so in one symbol 2bits we can send.
So 1 Symbol = 2 bits.
So total no of Bits sent in a subframe = 2 * 4200 = 8400 bits.
So capacity = 8400 / 1ms = 8.4 MBPS
So capacity in 5MHz Bandwidth with QPSK Modulation with normal cyclic Prefix is 8.4MBPS.
if Modulation scheme is BPSK, 1 bits in a symbol = 1 * 4200 / 1ms = 4.2 MBPS
if Modulation scheme is 64QAM , 6 bits in a symbol = 6 * 4200 / 1ms = 25.2 MBPS.
Presentation
LTE EARFCN Equation
Fdownlink = FDL_Low + 0.1 (NDL - NDL_Offset)
Where,
NDL is downlink EARFCN
NUL is uplink EARFCN
NDL_Offset is offset used to calculate downlink EARFCN
NUL_Offset is offset used to calculate uplink EARFCN
768
EVENTA1 serving becomes better than threshold
The LTE Event A1 is triggered when the serving cell becomes better than a threshold. The event is triggered when the following condition is
true:
MEAsserv - Hyst > Threshold
Triggering of the event is subsequently cancelled when the following condition is true:
MEAsserv + Hyst < Threshold
The hysteresis can be configured with a value between 0 and 30 dB.
EVENTA5 Serving becomes worse than thr.1and neighbour becomes better than thr.2
LTE Event A5 is triggered when the serving cell becomes worse than threshold-1 while a neighbouring cell becomes better than threshold-2. The
event is triggered when both of the following consitions are true:
MEASserv + Hyst < Threshold-1
MEASneigh + Oneigh,freq + Oneigh,cell - Hyst >Threshold-2
Triggering of the event is subsequently cancelled when either of the following conditions are true:
MEASserv - Hyst > Threshold-1
MEASneigh + Oneigh,freq + Oneigh,cell + Hyst <Threshold-2
Event B1
The LTE Event B1 is triggered when a neighbouring inter-system cell becomes better than a threshold. The event is triggered when the following
condition is true:
MEASneigh + Oneigh,freq - Hyst > Threshold
Triggering of the event is subsequently cancelled when the following condition is true:
MEASneigh + Oneigh,freq + Hyst < Threshold
Event B2
The LTE Event B2 is triggered when the serving cell becomes worse than threshold-1 while a neighbouring inter-system cell becomes better
than threshold-2. The event is triggered when both of the following conditions are true:
MEASserv + Hyst < Threshold-1
MEASneigh + Oneigh,freq - Hyst > Threshold-2
Triggering of the event is subsequently cancelled when either of the following conditions are true:
MEASserv - Hyst > Threshold-1
MEASneigh + Oneigh,freq + Hyst < Threshold-2
a1 threshold2a:-108
a2 threshold2:-110
a3 a3offset:6
a4 threshold4:-123
a5 threshold3a:-104 Others
threshold3:-106 Lte
3G – 4G Internetworking
3G
CELL_DCH
CELL_DCH
CELL_DCH
CELL_PCH,URA_PCH
UTRA_IDLE
This feature requires WCDMA/GERAN neighbor cell configuration data to initiate WCDMA/GERAN
measurements and the CS fallback procedure towards WCDMA/GERAN.
LTE56: Inter-RAT Handover to WCDMA
This feature is required for Handover to WCDMA PS Domain. The eNB takes the decision to start
Handover procedure based on measurements delivered by the UE.
LTE736: CS Fallback to UTRAN (with PS HO)
This feature requires WCDMA neighbor cell configuration data to initiate WCDMA measurements
and the hand over procedure towards WCDMA as for LTE56. The vendor templates for LNREW
support "csfbPsHoAllowed". The operator need to manually configure additional CSFB parameters
and to activate the feature. By default the feature is disabled and set to csfbPsHoAllowed =
forbidden.
LTE736: CS Fallback to UTRAN (with PS HO)
This feature requires WCDMA neighbor cell configuration data to initiate WCDMA measurements
and the hand over
LTE762: Idle mode mobility from LTE to WCDMA, GSM or other LTE bands
This feature requests SIB broadcast of information to support idle mode mobility for inter-RAT
neighbor cells.
LTE498: RAN Information Management for GSM
This feature brings a mechanism for automatic GSM SysInfo provisioning and eliminating the need
for manual configuration; requires IS-NACC for LTE (BSS21355) feature in GSM.
LTE1196: RAN Information Management for WCDMA
This feature brings a mechanism for automatic WCDMA SysInfo provisioning and eliminating the
need for manual configuration.
LTE984: GSM Redirect with System Information
This feature speeds up the redirection procedure by targets cells SysInfo provisioning with no
need for manual configuration.
LTE1197: UTRAN redirect with system information
This feature speeds up the redirection procedure by targets cells SysInfo provisioning with no
need for manual configuration.
LTE
RRC CONNECTED RAN2176 LTE PS HANDOVER
RRC CONNECTED RAN2435 CSFB with HO
RRC_IDLE RAN2717 Smart Layering
RRC_IDLE RAN2067 LTE interworking
RRC_IDLE RAN2067 LTE interworking
RAN2717 Smart LTE Layering (3G Connected to 4G Idle)
A& R
MOBILITY
INTEGRITY
PRACH
UTILIZATION
USER
System Program Reports RSLTE000
System Program Reports RSLTE001(Cell Level)
Accessibilty & Retainability RSLTE038
Service Retainability RSLTE037
S1 Interface accessibility RSLTE003
Neighbor HO analysis(Inter & Intra Rel Level) RSLTE031
Neighbor HO analysis(Inter) RSLTE005
Neighbor HO analysis(Utran) RSLTE044
Neighbor HO analysis(GSM) RSLTE045
BLER RSLTE067
High TA RSLTE058
PRB utiliztion RSLTE017
Active User at eNB RSLTE017
Active User at Cell level RSLTE027
Poor RRC SR
High TA( RSLTE058)
Low Coverage Area
HW suspected or alarm
HOSR
High TA( RSLTE058)
Low Coverage Area
HW suspected or alarm
PCI/RSI collision
Physical Optimization based on TA
Hardware alarms and history
HO fail due to prep/Exec?
Target cell distance(forbidden if it is far)
UL RSSI issue with source/Target
PCI/RSI collision check
PHR
CIO Tuning
Neighbor Ho report
T304 (Intera LTE)
CIO(+3(delay Ho),-3(Early HO)
HO Blacklisting
Automatic neighbor removal
Actionable KPIs Tuned Value Abbreviated Name MO Class
• Basic parameters
• Basic parameters
• Basic parameters
• Basic parameters
• Advanced parameters
• Advanced parameters
• Advanced parameters
• Basic parameters
• Basic parameters
• Advanced parameters
• Basic parameters
• Advanced parameters
• Advanced parameters
• Advanced parameters
• Advanced parameters
Full Name 3GPP Name Data Type Classification
1
Description
Indicates the maximum number of HARQ transmissions in DL that is configured for each UE at initial access to a spec
The maximum content resolution timer parameter defines the maximum amount of time allowed for contention resolu
The parameter defines an initial Modulation and Coding Scheme (MCS) to be used on PUSCH for other use than random acce
The parameter defines the maximum code rate for random access procedure messages 4 (SRB0 message). This maximum code rate is taken into ac
For small bandwidth system a sufficient number of HARQ retransmission or according segmentation is applied in order to reach to the
Cell Individual Offset (CIO) of Neighbor cells for insertion into the CIO Cell List of EUTRA Serving or Neighbor Carrier Measur
All CIOs different from zero will be considered by eNB for Measurement Configuration (up to a limit of 32 CIOs per carrier
Threshold for RSRP of intra-frequency neighbor cell. If RSRP of serving value < Th4 then re-direct is triggered.
The dBm value is mapped to the 3GPP IE value according to TS 36.133:
* -140 dBm means a threshold lower than -140 dBm.* values between -139 dBm and -44 dBm mean a threshold lower than the configured value but hi
* -43 dBm means a threshold higher than or equal to -44 dBm
This parameter defines the cell specific nominal power for the PUSCH. Used for P0_PUSCH calculation in UE uplink power control equation (P1) for contr
during (re)transmission corresponding to a received PDCCH with DCI format 0 associated with a new packet transmission. This parameter is used to co
Transmission power of the downlink reference signals in a cell is boosted (positive value) respectively deboosted (negative value) c
Defines the time period for the indication of the UE inactivity in both DL and UL directions.
The eNodeB will dynamically change the value of parameter inactivityTimer for each UE which is configured for DRX. The value configured at cell setup wil
is based on the comparison between UE mobility and data traffic characteristics as further described in LTE585-Smar
Cell Individual Offset (CIO) of Neighbor cells for insertion into the CIO Cell List of EUTRA Serving or Neighbor Carrier Measur
All CIOs different from zero will be considered by eNB for Measurement Configuration (up to a limit of 32 CIOs per carrier
The parameter defines the number of consecutive CQI DTX detections causing radio link failure indication. Special value 0 means that
Number of concecutive CQIs required for RL recovery.The parameter defines number of consecutive CQI non-DTX detections causing radio l
Range and step
1...16, step 1
8ms (0), 16ms (1), 24ms (2), 32ms (3), 40ms (4), 48ms (5), 56ms (6), 64ms (7)
100ms (0), 200ms (1), 300ms (2), 400ms (3), 600ms (4), 1000ms (5), 1500ms (6), 2000ms (7)
0...20, step 1
-24dB (0), -22dB (1), -20dB (2), -18dB (3), -16dB (4), -14dB (5), -12dB (6), -10dB (7), -8dB (8), -6dB (9), -5dB (10), -4dB
(11), -3dB (12), -2dB (13), -1dB (14), 0dB (15), 1dB (16), 2dB (17), 3dB (18), 4dB (19), 5dB (20), 6dB (21), 8dB (22), 10dB
(23), 12dB (24), 14dB (25), 16dB (26), 18dB (27), 20dB (28), 22dB (29), 24dB (30)
-3dB (700), 0dB (1000), 1.77dB (1177), 3dB (1300), 4.77dB (1477), 6dB (1600)
5...65535 s, step 1 s
1000ms (0), 3000ms (1), 5000ms (2), 10000ms (3), 15000ms (4), 20000ms (5), 30000ms (6)
32...1544, step 8
-24dB (0), -22dB (1), -20dB (2), -18dB (3), -16dB (4), -14dB (5), -12dB (6), -10dB (7), -8dB (8), -6dB (9), -5dB (10), -4dB
(11), -3dB (12), -2dB (13), -1dB (14), 0dB (15), 1dB (16), 2dB (17), 3dB (18), 4dB (19), 5dB (20), 6dB (21), 8dB (22), 10dB
(23), 12dB (24), 14dB (25), 16dB (26), 18dB (27), 20dB (28), 22dB (29), 24dB (30)
50ms (0), 100ms (1), 150ms (2), 200ms (3), 500ms (4), 1000ms (5), 2000ms (6)
0...250, step 1
1...8, step 1
Formula for Getting Internal Value Default Value Default Value Notes
internal_value = gui_value 5
dlChBw of LNCEL - if dlChBw set to '1.4 MHz', dlRsBoost must be configured to '0dB'
dlMimoMode of LNCEL - If dlMimoMode is set to 'SingleTX', dlRsBoost must be different to '1.77d
dlpcMimoComp of LNCEL - if dlpcMimoComp is set to '3dB', dlRsBoost must be less than or equal to '3dB', if dlRsBoost is not set to '0dB', dlpcM
qci1ProtectionTimer of LNCEL
Related Features Interfaces
• EM <-> LTE BTS
• LTE41 PDCP, MAC & RLC support (standard) • LTE BTS <-> RAC
• RAC <-> RACApp
• LTE430 DL power boosting for control channels (standard) • EM <-> LTE BTS
• LTE568 DL adaptive closed loop MIMO (4x2) (optional) • LTE BTS <-> RAC
• LTE117 Cell Bandwidth - 1,4 MHz (standard) • RAC <-> RACApp
• LTE41 PDCP, MAC & RLC support (standard) • EM <-> LTE BTS
• LTE BTS <-> RAC
• LTE2430 QCI1 establishment triggered inactivity timer (standard) • RAC <-> RACApp
applyOutOfSyncState
LNBTS Radio problem indication based on CQI DTX nCqiDtx
LNBTS Number of PUSCH DTX detections for radio link problem rlpDetMaxNUl
LNBTS Time of PUSCH DTX detections for radio link problem rlpDetMaxTUl
1...7, step 1 5
1...16, step 1 3
n1 (0), n2 (1), n3 (2), n4 (3), n6 (4), n8 (5), n10 (6), n20 (7) -
1...10, step 1 10
0...100, step 1 50
1...8, step 1 2
1...20, step 1 3
1...20, step 1 3
RAB Improvement 3S to 5S t311 LNCEL Timer T311 ➨(4): P-CSCF receives abo
RAB Improvement 104 to 72 ulsMinTbs LNCEL Minimum UL transport block size ➨(5): Dedicated bearer is e
CIO(+3(delay Ho),- Cell individual offsets of other neighbor ➨(6): In parallel to (5), P-C
Intra LTE_HO cellIndOffNeigh LNREL
3(Early HO) cells
Intra LTE_HO t304IntraLte LNCEL Timer T304 intra-LTE ➨(7): Originating terminal s
Radio problem indication based on CQI ➨(8): This establishes voic
RAB Improvement 100 to 150 ncqiDTX LNBTS
DTX
Radio problem recovery based on CQI ➨(9): After the confirmation
RAB Improvement 2 to 8 nCqiRec LNBTS
DTX
➨(10): Terminating termina
➨(11): The "Ser" at termina
➨(12): The terminating term
QCI of value 1.
Header Info
SIP INVITE Request INVITE
➨(2): INVITE message is transmitted to VoLTE terminating terminal via P-CSCF/S-CSCF/TAS. The message consists of terminal IDs, codes used by originating terminal.
➨(3): Terminating terminal responds with "183 session progress". This message carries codecs used by terminating terminal.
➨(4): P-CSCF receives above message and signals PCRF to establish dedicated bearer for voice media.
➨(5): Dedicated bearer is established by PGW, SGW, eNB and originating terminal. Appropriate QCI is assigned to such dedicated bearer. QCI of value 1 is used for conve
➨(6): In parallel to (5), P-CSCF forwards "183 session progress" message to originating terminal. Using this, originating terminal compares codecs of terminating terminal w
➨(7): Originating terminal sends PRACK to terminating terminal which notifies codec to be used. Terminating terminal responds with "200 OK".
➨(8): This establishes voice bearer. This is confirmed by "UPDATE" message initiation from originating terminal and response of "200 OK" from terminating terminal.
h "200 OK".
00 OK" from terminating terminal.
tablishment of session. Now voice traffic can flow through established dedicated voice bearer which utilizes
LTE Features
DL power boosting for control channel: (Downlink PCFICH transmission power boost (dlPcfichBoost))
DL power boosting for control channel: (Downlink PCFICH transmission power boost (dlPcfichBoost))
DL target BLER:Avg_DL_PDCP Thpt is Improved by ~437 kbps and PDSCH MCS is improved from 10.64 to 11.50
Paramater Name
sNonIntrsearch
Cell Count
threshSrvLow
Cell Count
sIntrasearch
Cell Count
qHyst
Cell Count
Description
Parameter ‘allowPbIndexZero’ is to be changed for the trial from 0 (False) to 1 (True) in 5 sites . You can keep this trial as inte
By setting ‘allowPbIndexZero’ = 1 ( true ) along with dlRSboost = 0dB; we shall be able to use the power from the blanked Reference signal for boosti
We shall be able to increase the power of PDSCH B symbols by 0.97 dB. Since we are only increasing power of the B symbols hence the overall increase is PDSCH power
by only 0.21 dB ).
Hence we might observe minor improvement in throughput
Objective is to improve user Throughpu,t.introduces a new uplink link adaptation algorithm based on available Extended Uplink Link Adaptation (E-ULA), which pro
modulation and coding scheme (MCS) selection. Improvement of Uplink throughput observed in Lucknow & Jhansi, marginal dec
PUSCH MCS improved in Lucknow,varansi & Jhansi
There is no major changes observed on other KPI’s
Selects a working mode for UL power control. Offers various combinations between open-loop and closed-loop control for PUCCH and PU
Activates autonomous removal of unused UTRAN neighbour relation and neighbour cell configuration information
Activates autonomous removal of unused LTE neighbour relation and neighbour information
Activates the feature 'Radio Link Failure (RLF) based RRC connection reestablishment (RCR)'
To improve IRAT execution Success rate
To imrove DL cell throughput.
The LTE1140: Intra-frequency Load Balancing supports load balancing for cells deployed on the same frequency layer.parameter is actI
Value of parameter ie dlPcfichBoost,dlPhichBoost need to be validated
ActSmartDrx : (Ranges: True / False) :Parameter allows for activating (true) SMART DRX feature. Feature introduces Short DRX cycle together with
Longer values of short cycle timer gives longer possibility for UE to follow short DRX Cycles until DRX Long Cycles will s
After expiration of drxShortCycleT it is assumed that UE can follow Long DRX Cycles to achieve better battery savings (longer DRX
Impacts After disabling Smart DRX feature:
Higher scheduler flexibility, Possible lower delays may be experienced for new DL transmissions (transmission of DL data will be not be delayed to
observed improvement in latency after tdiscard timer change from 750 to 500
This feature introduces means for detecting neighbour inter enb cells which are temporarily excluded as potential target candidates for LTE Inter enb Handovers.It w
preparation failures by avoiding handover preparation in some scenarios where success of handover preparation is considered as
actTempHoBlacklisting: Current value : FALSE & Proposed value : TRUE
If the success of a handover (HO) preparation is considered unlikely, the HO is temporarily blacklisted. It was implemented on 13th June on PLMN level. It has given ~
S1 setups SR.
Interference aware UL power control feature improves the uplink (UL) cell capacity and the cell-edge performance.
The interference-aware uplink power control is used for the power control on the physical uplink shared channel (PUSCH).
he eNB uses its own measurements and the UE's measurements as input & controls the UE-specific transmit power and the UL interference in t
Range : 0 to 7 : ( 0: PuschOLPucchOL & 1: PuschOLPucchCL & 2: PuschCLPucchOL & 3: PuschCLPucchCL & 4: PuschCLSrsPucchOL & 5: PuschCLSrsPucchCL & 6: P
dlPcfichBoost : Transmission power of the Physical Control Format Indicator Channel is boosted by set value.PCFICH informs about the number of PDCCH symbols per
the whole sub frame is lost.The eNB supports dedicated power control settings for the PCFICH in order to ensure that especially cell edge UEs can p
With this feature Better detection of PCFICH indicating the number of OFDM (Orthogonal Frequency-Division Multiplexing) symbols for the PDCCH (Physical Downlink C
channel estimations will be possible.
dlPcfichBoost : Transmission power of the Physical Control Format Indicator Channel is boosted by set value.PCFICH informs about the number of PDCCH symbols per
the whole sub frame is lost.The eNB supports dedicated power control settings for the PCFICH in order to ensure that especially cell edge UEs can p
With this feature Better detection of PCFICH indicating the number of OFDM (Orthogonal Frequency-Division Multiplexing) symbols for the PDCCH (Physical Downlink C
channel estimations will be possible.
This parameter defines acceptable target Block Error Ratio (BLER) for downlink Link Adaptation in percent’s.
Ranges : 0.1...99.9 %, step 0.1 %
Current Value :10% Proposed Value : 12%
LNCEL Parameter
Paramater value
4
7307
2
7307
44
7307
2dB
2037
Observations –
Agg 4+ Agg 8 usage reduced by ~ 4.77%
CCE blocking rate reduced from 0.011 to 0.008
DL Cell Throughput improved by ~275 Kbps, day wise trend suggest throughput increase was observed on 30 th April.
Paramater Name Paramater value
12 threshold2Wcdma -118 -114 -112
213 Cell Count 7288 118 114
8 hysThreshold2Wcdma 0 1 2
213 Cell Count 213 1831 5476
4dB
5483 tReselEutr 2 3 4
Cell Count 5495 162 1863
hysA3Offset 0 0.5 1
Cell Count 213 1831 5476
as observed on 30 th April.
Parameter Name MOC_FL16A MOC_FL16 Default/Delta
actUlLnkAdp LNCEL_PS LNCEL SCF Default value
drxSmartProfile2drxShortCycle SDRX LNCEL_DC Delta
threshold2a LNCEL_HC LNCEL_HC SCF Default value
threshold2InterFreq LNCEL_HC LNCEL_HC SCF Default value
threshold2Wcdma LNCEL_HC LNCEL_HC SCF Default value
cqiPerNp MPUCCH LNCEL Delta
b2Threshold2UtraEcn0 LNHOW LNHOW SCF Default value
b2Threshold2UtraRscp LNHOW LNHOW SCF Default value
hysB2ThresholdUtra LNHOW LNHOW SCF Default value
actIfHo LNBTS LNBTS SCF Default value
actInterFreqLB LNBTS LNBTS Delta
actSrvccToGsm LNBTS LNBTS Delta
actQci1eVTT LNCEL_PS LNCEL Delta
qci1DlTargetBler LNCEL_PS LNCEL Delta
qci1UlTargetBler LNCEL_PS LNCEL Delta
acteNACCtoGSM LNBTS LNBTS SCF Default value
threshold2GeranQci1 LNCEL_HC LNCEL_HC SCF Default value
b2threshold1GeranQci1 LNHOG LNHOG SCF Default value
b2threshold2RssiGeranQci1 LNHOG LNHOG SCF Default value
eUlLaLowMcsThr LNCEL_PS LNCEL SCF Default value
eUlLaLowPrbThr LNCEL_PS LNCEL SCF Default value
qci1ThroughputFactorUl LNCEL_PS LNCEL SCF Default value
qci1ThroughputFactorDl LNCEL_PS LNCEL SCF Default value
qci1HarqMaxTrDl LNCEL_PS LNCEL SCF Default value
qci1ReconStopTimer LNCEL_PS LNCEL SCF Default value
actInterFreqServiceBasedHo LNBTS LNBTS SCF Default value
threshold1 LNCEL_HC LNCEL_HC SCF Default value
a3offset LNCEL_HC LNCEL_HC SCF Default value
threshold2Wcdma LNCEL_HC LNCEL_HC SCF Default value
b2Threshold1Utra LNHOW LNHOW SCF Default value
b2Threshold2UtraEcNo LNHOW LNHOW SCF Default value
b2Threshold2UtraRscp LNHOW LNHOW SCF Default value
threshold2GERAN LNCEL_HC LNCEL_HC SCF Default value
b2Threshold1GERAN LNHOG LNHOG SCF Default value
hysB2thresholdGERAN LNHOG LNHOG SCF Default value
threshold4 LNCEL_HC LNCEL_HC SCF Default value
actConvVoice LNBTS_BEARER LNBTS_BEARER SCF Default value
actDlsVoicePacketAgg LNCEL_PS LNCEL_PS Delta
ulsMaxPacketAgg LNCEL_PS LNCEL_PS Delta
actDlsOldtc LNCEL_PS LNCEL_PS Delta
maxNumQci1Drb LNCEL_AC LNCEL_AC SCF Default value
addNumQci1DrbRadioReasHo LNCEL_AC LNCEL_AC SCF Default value
addNumQci1DrbTimeCriticalHo LNCEL_AC LNCEL_AC SCF Default value
voiceSuppMatchInd LNBTS LNBTS Delta
qciTab1delayTarget LNBTS_QCITAB LNBTS_QCITAB SCF Default value
qciTab1maxGbrDl LNBTS_QCITAB LNBTS_QCITAB SCF Default value
qciTab1maxGbrUl LNBTS_QCITAB LNBTS_QCITAB SCF Default value
qciTab1resType LNBTS_QCITAB LNBTS_QCITAB SCF Default value
qciTab1rlcMode LNBTS_QCITAB LNBTS_QCITAB SCF Default value
qciTab1drxProfileIndex LNBTS_QCITAB LNBTS_QCITAB SCF Default value
drxProfile2drxInactivityT LNCEL_DRX LNCEL_DC SCF Default value
drxProfile2drxLongCycle LNCEL_DRX LNCEL_DC SCF Default value
drxProfile2drxOnDuratT LNCEL_DRX LNCEL_DC SCF Default value
drxProfile2drxProfileIndex LNCEL_DRX LNCEL_DC SCF Default value
drxProfile2drxProfilePriority LNCEL_DRX LNCEL_DC SCF Default value
drxProfile2drxRetransT LNCEL_DRX LNCEL_DC SCF Default value
qciTab1schedulPrio LNBTS_QCITAB LNBTS_QCITAB SCF Default value
qciTab5drxProfileIndex LNBTS_QCITAB LNBTS_QCITAB Delta
drxProfile4drxProfileIndex LNCEL_DRX LNCEL_DC SCF Default value
drxProfile4drxRetransT LNCEL_DRX LNCEL_DC Delta
drxProfile4drxInactivityT LNCEL_DRX LNCEL_DC SCF Default value
drxProfile4drxLongCycle LNCEL_DRX LNCEL_DC SCF Default value
drxProfile4drxOnDuratT LNCEL_DRX LNCEL_DC Delta
drxProfile4drxProfilePriority LNCEL_DRX LNCEL_DC SCF Default value
qciTab5resType LNBTS_QCITAB LNBTS_QCITAB SCF Default value
qciTab5rlcMode LNBTS_QCITAB LNBTS_QCITAB SCF Default value
qciTab5schedulPrio LNBTS_QCITAB LNBTS_QCITAB SCF Default value
qciTab5schedulType LNBTS_QCITAB LNBTS_QCITAB Delta
qciTab5lcgid LNBTS_QCITAB LNBTS_QCITAB Delta
n310Qci1 LNCEL LNCEL Delta
t310Qci1 LNCEL LNCEL Delta
actRrcConnNoActivity LNBTS LNBTS Delta
qci1ProtectionTimer LNCEL_PS LNCEL Delta
actMultBearers LNBTS_BEARER LNBTS_BEARER SCF Default value
actMultGbrBearers LNBTS_BEARER LNBTS_BEARER Delta
actEnhAcAndGbrServices LNBTS_BEARER LNBTS_BEARER SCF Default value
gbrCongHandling LNCEL_PS LNCEL_PS SCF Default value
qcitab2drxProfileIndex LNBTS_QCITAB LNBTS_QCITAB SCF Default value
qcitab2maxGbrDl LNBTS_QCITAB LNBTS_QCITAB Delta
qcitab2maxGbrUl LNBTS_QCITAB LNBTS_QCITAB Delta
qcitab2qciSupp LNBTS_QCITAB LNBTS_QCITAB SCF Default value
qcitab2resType LNBTS_QCITAB LNBTS_QCITAB SCF Default value
qcitab2rlcMode LNBTS_QCITAB LNBTS_QCITAB SCF Default value
qciTab2schedulPrio LNBTS_QCITAB LNBTS_QCITAB SCF Default value
actPdcpRohc LNBTS_BEARER LNBTS_BEARER SCF Default value
pdcpProf101rohcmaxCid LNBTS_BEARER LNBTS_BEARER Delta
actEmerCallRedir LNBTS LNBTS SCF Default value
actIMSEmerSessR9 LNBTS_BEARER LNBTS Delta
addEmergencySessions MPUCCH LNCEL_AC Delta
maxNumRrcEmergency MPUCCH LNCEL_AC Delta
actTtiBundling LNCEL_PS LNCEL_PS Delta
harqMaxTrUlTtiBundling LNCEL_PS LNCEL_PS SCF Default value
qciTab1enforceTtiBundling LNBTS_QCITAB LNBTS_QCITAB SCF Default value
qciTab5enforceTtiBundling LNBTS_QCITAB LNBTS_QCITAB SCF Default value
qciTab6enforceTtiBundling LNBTS_QCITAB LNBTS_QCITAB SCF Default value
qciTab7enforceTtiBundling LNBTS_QCITAB LNBTS_QCITAB SCF Default value
qciTab8enforceTtiBundling LNBTS_QCITAB LNBTS_QCITAB SCF Default value
qciTab9enforceTtiBundling LNBTS_QCITAB LNBTS_QCITAB SCF Default value
ttiBundlingBlerThreshold LNCEL_PS LNCEL SCF Default value
ttiBundlingSinrThreshold LNCEL_PS LNCEL SCF Default value
ttiBundlingBlerTarget LNCEL_PS LNCEL SCF Default value
ttibOperMode LNCEL_PS LNCEL Delta
ulsMinRbPerUe LNCEL_PS LNCEL_PS SCF Default value
ulsMinTbs LNCEL_PS LNCEL_PS Delta
actRLFbasedRCR LNBTS LNBTS SCF Default value
rlfBasedRCRdefault LNBTS LNBTS SCF Default value
rlfBasedRCRsupported LNADJ LNADJ SCF Default value
actSrvccToWcdma LNBTS LNBTS Delta
preventPsHOtoWcdma LNBTS LNBTS SCF Default value
srvccAllowed ANRPRW LNRELW SCF Default value
srvccAllowed ANRPRW LNRELW SCF Default value
srvccHoInd ANRPRW LNDJW SCF Default value
srvccHoInd ANRPRW LNDJW SCF Default value
actServBasedMobThr LNBTS LNBTS Delta
threshold2InterFreqQci1 LNCEL LNCEL_HC Delta
threshold2WcdmaQci1 LNHOW LNCEL_HC SCF Default value
threshold2aQci1 LNCEL_HC LNCEL_HC Delta
b2Threshold1UtraQci1 LNHOW LNHOW Delta
measQuantityUtra LNCEL LNCEL_HC SCF Default value
b2Threshold2UtraRscpQci1 LNHOW LNHOW Delta
b2Threshold2UtraEcN0Qci1 LNHOW LNHOW Delta
a2RedirectQci1 LNCEL_HC LNCEL_HC Delta
Parameter Updated Internal Value GUI Value Changes required
6 Fulla NO
40 40 40ms Yes
42 42 NO
40 40 NO
22 22 NO
40 40 40ms Yes
20 -14 NO
13 -102 NO
0 0 NO
1 1 enabled NO
1 1 true Yes
1 1 true Yes
1 1 1 Yes
20 20 2 Yes
2 2 2 Yes
1 1 NO
22 -118 NO
BLANKS BLANKS NO
BLANKS BLANKS NO
1 1 NO
1 1 NO
16 1.6 NO
16 1.6 NO
5 5 NO
10 1 NO
0 0 NO
60 -80 NO
6 3 dB NO
22 -118 NO
20 -120 NO
20 -14dB NO
13 -102 NO
22 -118 NO
21 -119 NO
0 0 dB NO
18 -122 NO
1 1 NO
0 0 0 Yes
1 1 1 Yes
1 1 1 Yes
100 100 NO
15 15 NO
20 20 NO
2 2 supported Yes
80 80ms NO
256 256 kbps NO
256 256 kbps NO
0 GBR NO
1 RLC_UM NO
2 2 NO
4 4 NO
40 40 ms NO
6 6 NO
2 2 NO
40 40 NO
4 4 NO
5 5 NO
4 4 4 Yes
4 4 NO
16 16 16 Yes
500 500 NO
320 320 NO
10 10 10 Yes
20 20 NO
1 NonGBR NO
0 RLC_AM NO
9 9 NO
0 0 SIGNALLING Yes
0 0 0 Yes
10 10 n10 Yes
2000 2000 2000ms Yes
1 1 1 Yes
40 40 40s Yes
1 1 NO
1 1 1 Yes
1 1 NO
2 l2andl3 NO
2 2 NO
2048 2048 2048 kbps Yes
840 840 840 kbps Yes
1 Enable NO
0 GBR NO
1 RLC_UM NO
7 7 NO
1 1 NO
2 2 2 Yes
1 Enabled NO
1 1 1 Yes
45 45 45 Yes
145 145 145 Yes
1 1 1 Yes
12 -100 NO
1 cpichRscp NO
0 NA NO
0 0 NO
0 0 NO
0 0 NO
0 0 NO
15 15 NO
10 1 NO
12 0.06 NO
0 0 blerBasedNotWithMeasGap Yes
3 3 NO
72 72 72 Yes
1 1 NO
1 1 NO
1 1 NO
1 1 1 Yes
0 None NO
0 Allowed NO
0 Allowed NO
0 PS and CS NO
0 PS and CS NO
1 1 1 Yes
40 40 40 Yes
26 -114 NO
42 42 42 Yes
24 24 -116 Yes
0 cpichRSCP NO
13 13 -102 Yes
20 20 -14 Yes
0 0 0 Yes
Parameters Grouped by features
SRVCC to WCDMA
FEATURE ID FEATURE NAME CAPACITY
feature is to command the UE to leave LTE network if the LTE coverage is
ending and handover the VoIP call (QCI = 1)
LTE872
to WCDMA network via Single Radio Voice Call Continuity procedure – in
the IMS capable environment
VOLTE CALL FLOW
F)
- CSC
n (P
ctio
l Fun
o
ntr
Co
s ion
es
alS
x y -C
Pro