Professional Documents
Culture Documents
VoLTE performance
optimization
Basic
Performance
Enhance
Basic PUSCH DTX schedule policy
PuschDtxSchStrategy
Performance (No license)
Enhance
RoHC RohcSwitch
RoHC HighestMode
RoHC Profiles
TTIB(need License:LT1S00TTIB00)UlSchSwitch-TtiBundlingSwitch
QCI5 DRX parameter 1,QCI5 have the same DRX Parameter with default Bearer(such
delay of QCI too longer,so Long DRX cycle of QCI5 is advised to
2,UE级DRX参数与QCI级DRX参数间的关系:
VoLTE EMC CnOperatorId
Enhance
Features VoLTE EMC EmcEnable
HoCommOptSwitch-
Gap Optimization Switch-Based
BasedSriGapOptSwitch
SRI
SRI and GAP optimization
Gap Optimization Switch-Based HoCommOptSwitch-
SRI(DRX state) DrxBasedSriGapOptSwitch
Preemption RacAlgoSwitch-PreemptionSwitch
Preemption UeNumPreemptSwitch-
IntraOpUeNumPreemptSwitch
Preemption UeNumPreemptSwitch-
InterOpUeNumPreemptSwitch
None ProtocolSupportSwitch:SupportS1Ue
voice policy negotiation CapMatchMsg~0
Mobility Qci
QCI priority for mobility
Mobility QciPriorityForHo
The Default value in Function
MO Recommend value for VOIP
version describe
Schedule FPD
CELLULPCCOMM -115
-105 power control
FPD
e DRX Parameter with default Bearer(such as QCI9/8),but Long DRX Cycle of QCI5 too longer,the setup DRX FPD
,so Long DRX cycle of QCI5 is advised to be smaller than 320ms;
QCI级DRX参数间的关系:
EMC NA NA Emergency Call
ENODEBALGOSWITCH ON ON connection
mobility
management
ENODEBALGOSWITCH ON ON FPD
connection
mobility
management
CELLPUCCHALGO OFF ON FPD
CELLPUCCHALGO OFF ON
only used for parameter check,if VoLTE enable Indicates the logical channel group configuration.
in eRAN7.0/eRAN8.0,This parameter should
Should
configurekeep the same for whole
to LCG_Profile_0; fromnetwork.Because
eRAN8.1, this Indicates the length of a PDCP sequence number of
128 continous
parameter shouldPDCPnot packets
configurediscarded
to will cause a UL DRB in RLC UM.
inconsistent HFN between cipher and decipher
side, it will bring the bad voice experience when
Should keep the same for whole network. RLC SN Indicates the length of a UL RLC sequence number
5bit means Rx Window Size = 16; too small Rx in UM. The length is permanently 10 bits in AM.
Should
Win Size keepwillthe same
cause for SN’s
RLC wholeerror-rollback
network. RLC, for
SN Indicates the length of a DL RLC sequence number
5bit means
example theRxfirstWindow Size =is received
RLC SN=1 16; too small
and Rx in UM. The length is permanently 10 bits in AM.
Default
Win Sizeis will
100ms cause RLC SN’s error-rollback , for Indicates the length of the PDCP discard timer.
example the first RLC SN=1 is received and
infinity is recommened according to LGU+ Case Indicates the length of the PDCP discard timer.
1,SIP invite may be divided two packet in
Indicates
TCP/IP layerthe timer
due togoverning the period the local
MTU in Terminal; Indicates the timer governing the period the local
eNodeB waits for a response message from the eNodeB waits for a response message from the
peer eNodeB when the UE is running services with peer eNodeB when the UE is running services with
Indicates
the QCI ofthe 1. timer
If thegoverning the period
timer expires, the
the eNodeB Indicates
the QCI ofthe 1. timer
If thegoverning the period
timer expires, the
the eNodeB
eNodeB waits for a response message from a UE eNodeB waits for a response message from a UE
when the UE is running services with the QCI of 1. when the UE is running services with the QCI of 1.
every 20ms expires,
If the timer had one thevoice packet.initiate
eNodeB And the cell
a UE Indicates
If the timerwhether
expires, to the
apply upper initiates
eNodeB limit control
a UEon
edge, when the UE power limitation, eNodeB have service data unit (SDU) segmentation at the radio
to select small TBS which smaller than the size of link control (RLC) layer in the uplink for VoIP
voice packet, so voice packet had to divide into services scheduled in non-TTI bundling mode and
For voice service, keep the number of RB not VoipTbsBasedMcsSelSwitch: Indicates whether
change and select the smaller MCS can dedue the the modulation and coding scheme (MCS) index is
bler and HARQ retransmission selected based on the transport block size (TBS) in
downlink scheduling for VoIP services. If this
If the UE transmit power is not limited, adaptive UlLast2RetransSchOptSwitch: Indicates whether to
retransmission is used and the number of RBs enable optimization on the scheduling policy for
increases in the last two retransmissions to increase the last two retransmissions. If this switch is on,
the receive success rate of the last two optimization on the scheduling policy for the last
If this switch is On, TBS index adjustment DlRetxTbsIndexAdjOptSwitch: Indicates whether
optimization in retransmissions is enabled. The to enable transport block size (TBS) index
TBS index is lowered for the scheduling of the last adjustment optimization in retransmissions.
two retransmissions, and the TBS index is
determined based on the CQI adjustment for the If this switch is On, TBS index adjustment
This ensures timely uplink scheduling on voice UlVoipSchOptSwitch: Indicatesiswhether
optimization in retransmissions enabled.toTheenable
services even when SR missing detection occurs, scheduling
TBS index is optimization
lowered forfor theVoIP servicesofinthe
scheduling thelast
thereby avoiding packet loss caused by the uplink. If this option and
two retransmissions, is deselected, this function
the TBS index is is
expiration of the PDCP packet discarding timer. disabled. If this option is selected, an uplink
when this switch and UlVoipSchOptSwitch
both on, can reduce UL voice packet delay
and UL packet
Indicates loss which
the switches related caused by(UL)
to uplink SR miss
detect, improve
scheduling voiceThe
in the cell. quality. Butareit used
switches will to
enable or the
increase disable specific ULofscheduling
consumption PUSCH functions.
RB and Indicates the scheduling policy for the initial
PuschDtxSwitch: Indicates whether the eNodeB
PUSCH transmission that is detected as
uses the physical uplink shared channel (PUSCH)
discontinuous transmission (DTX) when
discontinuous transmission (DTX) detection result
PuschDtxSwitch of the UlSchSwitch parameter is
during uplink (UL) scheduling. When this switch is
on. If the PuschDtxSchStrategy parameter is set to
turned on, the parameter applies to only cells
NEW_TX, initial transmission instead of
established on an LBBPd working in FDD mode. If
retransmission is performed when the initial
this switch is turned on, the eNodeB determines
PUSCH transmission is detected as DTX. If the
whether to perform adaptive retransmission during
PuschDtxSchStrategy parameter is set to
UL scheduling based on the PUSCH DTX
ADAPTIVE_RETX, adaptive retransmission is
detection result, and also adjusts the CCE
performed when the initial PUSCH transmission is
aggregation level of the physical downlink control
detected as DTX. This parameter does not apply to
channel (PDCCH) carrying downlink control
LTE TDD.
information (DCI) format 0 based on the result. If
this switch is turned off, the eNodeB does not use
the PUSCH DTX detection result during UL
scheduling.
Indicates the scheduling policy for the initial
PUSCH transmission that is detected as
discontinuous transmission (DTX) when
PuschDtxSwitch of the UlSchSwitch parameter is
on. If the PuschDtxSchStrategy parameter is set to
If PuschDtxSchStrategy set to ADAPTIVE_RETX, NEW_TX, initial transmission instead of
it can deduce the uplink packetloss, but it may retransmission is performed when the initial
caused that increase the uplink RB and CCE PUSCH transmission is detected as DTX. If the
spending. PuschDtxSchStrategy parameter is set to
ADAPTIVE_RETX, adaptive retransmission is
performed when the initial PUSCH transmission is
detected as DTX. This parameter does not apply to
LTE TDD.
If this parameter is set to VOIP_DELAYSCH, Indicates whether to enable delay-based dynamic
delay-based dynamic scheduling prioritization for scheduling prioritization for VoIP services. If this
VoIP services is enabled. Scheduling priorities are parameter is set to NO_DELAYSCH, delay-based
This option isadjusted
dynamically selected,based
the eNodeB
on VoIPestimates the UlVoLTEDataSizeEstSwitch:
packet delays Indicates
dynamic scheduling prioritization whether
for VoIP to
services
uplink traffic volume that is dynamically scheduled enable the estimation of traffic volume dynamically
for VoLTE services, which shortens the VoLTE scheduled for VoLTE services in the uplink.If this
packet delay, reduces the packet loss rate, improves option is deselected, this function is disabled. If
the voice service this option is selected, the eNodeB estimates the
Indicates the mode for allocating PUCCH
format 1/1a/1b code channel resources. The
setting of this parameter takes effect only
when the DeltaShift parameter is set to
When PucchPcDtxSinrSwitch is turned off,
the eNodeB does not process the measured
uplink SINR in the DTX state when PUCCH
DTX is detected. When
Indicates the period of power control for the
PUCCH. This switch applies only to LTE
FDD cells.该参数用于配置PUCCH的功控周
期。配置最小功控周期,当干扰变化时,
功控能够更快响应。
Indicates the offset to the target signal to
interference plus noise ratio (SINR) in power
control for the PUCCH. This switch applies
only to LTE FDD cells.抬升PUCCH SINR
Indicates the target UE transmit power for the
PUCCH expected by the eNodeB on condition
that normal demodulation can be performed.
P0NominalPUCCH set too high will increase
Indicates whether the P0NominalPUCCH
parameter affects closed-loop power control
(CL PC) for the PUCCH. The
PucchCloseLoopPcType parameter applies
only to LTE FDD cells. If this parameter is set
to NOT_USE_P0NOMINALPUCCH, the
P0NominalPUCCH parameter does not affect
CL PC for the PUCCH. If this parameter is set
to USE_P0NOMINALPUCCH,
Indicates whether to enable ROHC. the reference
Set this parameter to ON if the eNodeB is
The reasontoforsupport
expected O-Mode:
VoIP or video services.
【compression ratio】O mode is same
Profile1 usedefficency,
compression for RTP/UDP/IP
or gain of pdsch and pusch,
Profile2 usedand
as R-mode, forisUDP/IP
better than U-mode.
Profile3 used for ESP/IP
Profile4 used for IP
If TTI bundling is enabled, more transmission
opportunities are available to UEs within the delay
budget for VoIP services on the air interface,
thereby improving uplink coverage.
当为UE配置TTI bundling传输模式后,在VOIP
空口时延预算内获得更多传输机会,提高上行
覆盖。
This feature can be commerical, but now many
operator is verifying and not use large-scale,and
If endable
this featureuplink
dependsSPS,
onitUE
should enablesothe
capablity, not
CloseLoopSpsSwitch.
recommend enable now.there Because in order
maybe some to keep
Even if enalbe
the IBLER not downlink SPS,
deteriorate, it also
it need not need
dynamic adjust
downlink power adjust.
the UE power.
This feature can be commerical, but now many
operator is verifying and not use large-scale,and
Indicates thedepends
this feature policy for
on selecting a DRX
UE capablity, so parameter
not
group for a UE
recommend for which
enable the bearers
now. When DRX have multiple
for QCI1 is
1,performance Firstly,
QCIs. If this parameter suggest:
is set to QCI1
EnterDrxSwitch
DEFAULT(Default), =OFFthe DRX parameter group
2,power Saving firstly && SPS
enable,suggest:LongDRXCycle = 20ms,OD
Timer =10;IATimer =80ms;ReTxTimer =
8ms;SupportShortDrx = uu_Disable
3,power Saving firstly && SPS
disable,suggest:LongDRXCycle = 40ms,OD
Timer =10;IATimer =80ms;ReTxTimer =
8ms;SupportShortDrx = uu_Disable
When DRX for QCI1 is enable and longDRXCycle
bigger than 20ms, downlink SPS can't enable.
Indicates whether to enable or disable short DRX
cycles for non-power-saving UEs whose RFSP
indexes are contained in the RFSP index set.
eRAN7.0 V0.1
eRAN1.0 V0.3
eRAN1.0 V0.3
eRAN7.0 V1.0
eRAN6.0 V0.1
eRAN6.0 V0.1
eRAN6.0 V0.1
eRAN6.0 V0.1
eRAN8.1 V0.8
eRAN8.1 V0.8
eRAN8.1 V0.8
eRAN8.1 V0.8
eRAN8.1 V0.8
eRAN8.1 V0.8
eRAN6.0 V0.1
eRAN6.0 V0.1
eRAN6.0 V0.1
eRAN6.0 V0.1
eRAN7.0 V0.9
eRAN6.0 V0.1
eRAN6.0 V0.1
eRAN6.0 V0.1
eRAN6.0 V0.1
eRAN6.0 V0.1
eRAN6.0 V0.1
eRAN6.0 V0.1
eRAN6.0 V0.1
eRAN6.0 v0.4
eRAN6.0 v0.4
eRAN6.0 v0.4
eRAN6.0 v0.4
eRAN6.0 v0.4
eRAN8.0 V0.3
eRAN7.0 V0.9
eRAN8.0 V0.9
eRAN8.1S V1.0
PC050
eRAN8.1S V1.0
PC050
eRAN1.0 对核心网有要V0.1
eRAN6.0 V0.2
eRAN6.0 V0.1
eRAN6.0 V0.1
eRAN7.0 This import V0.4
in 3GPP
36.413
eRAN7.0 Release V0.1
eRAN7.0 V0.1
LTE
Function Object MO
ENODEBALGOSWITCH
SRVCC switch HoModeSwitch ENODEBALGOSWITCH
ENODEBALGOSWITCH
CsPsHOInd UTRANEXTERNALCELL UTRANEXTERNALCELL
QCI5 STANDARDQCI
InterRatPolicy
QCI1 STANDARDQCI
INTERRATPOLICYCFGGROUP
QCI1InterRatPolicy UtranHoCfg INTERRATPOLICYCFGGROUP
INTERRATPOLICYCFGGROUP
INTERRATHO INTERRATHOCOMMGROUP
INTERRATHO INTERRATHOCOMMGROUP
INTERRATHO INTERRATHOCOMMGROUP
INTERRATHO INTERRATHOCOMMGROUP
INTERRATHO INTERRATHOCOMMGROUP
INTERRATHO INTERRATHOCOMMGROUP
QCI1 InterRatHoPara INTERRATHO INTERRATHOCOMMGROUP
HOUTRAN INTERRATHOUTRANGROUP
HOUTRAN INTERRATHOUTRANGROUP
HOUTRAN INTERRATHOUTRANGROUP
HOUTRAN INTERRATHOUTRANGROUP
HOUTRAN INTERRATHOCOMM
CELLRESEL
CELLRESEL CELLRESEL
CELLRESEL
U
SET URRCTRLSWITCH RsvdPara1
SET URRCTRLSWITCH PROCESSSWITCH2
SET USTATETIMER RelocAnotherTmr
SET UCORRMALGOSWITCH CmpSwitch=CMP_IU_IMS_PROC_AS_NORMAL_PS_SWITCH
UMTS
SET URRCTRLSWITCH OptimizationSwitch4=SRVCC_RELOC_IN_USE_CS_KEY_SWITCH
RsvdSwPara1_bit5 ON
SNonIntraSearch
ThrshServLow
UMTS
SYSHO_CSIN_PERMIT_SWITC
RsvdPara1
H-1
L2U_SRVCC_WITH_PS_HO_S
PROCESSSWITCH2
WITCH-1
RelocAnotherTmr 5000
MP_IU_IMS_PROC_AS_NORMAL_PS_SWITCH ON
tch4=SRVCC_RELOC_IN_USE_CS_KEY_SWITCH ON
nSwitch6:CSPS_SYS_HO_IN_SMC_SWITCH ON
Remark
Open L2U of SRVCC switch
Close U's ability to switch voip
Open L2U the PS switch (must be consistent with the existing network strategy)
If the existing network of support L2U PS switch is labeled adjacent areas of support CS + PS SRVCC
Set QCI5 exclusive system configuration policy consistent with the data bearer, a separate set of different sy
Open L2U QCI 1 configuration policy group of SRVCC switch, turn off the redirection switch (open redirect
switch will cause voice dropped calls) and PS switch
Configuring L2U of B1 event-related threshold, reference baseline value, can be adjusted according to the
opening test and then optimize the effect, InterRatHoUtranB1ThdRscp to and UMTS side 2F threshold
agreement
Baseline recommend using ECIO trigger urban, suburban triggered by RSCP (required sub scene settings)
This switch prevents UE modified QCI bearer, the base station does not update issued A2 threshold (due
QCI1 threshold than other QCI threshold, UE can not update the special A2 threshold after New QCI1 bearer,
may cause dropped calls due to the switching is not timely)
Reference existing network value, to ensure (-128 + 2 * ThrshServLow> A2 threshold), to avoid the re-
election back to the UE 4G, just to establish business and cut back to GU, easily lead to dropped calls.
License
RoHC Need
TTB Need
SPS Need
Voice Characteristic
Awareness Need
Scheduling
Need(EUTRAN and
UtranSrvccSwitch
UTRAN)
ROHC Profile Profile1 Profile2 remark
0x0004 IP