Professional Documents
Culture Documents
GSM-To-UTMS Training Series - Introduction To The GENEX Probe - V1 - 0
GSM-To-UTMS Training Series - Introduction To The GENEX Probe - V1 - 0
Probe
l Replay control
l Data export
l Other functions
l Replay control
l Data export
l Other functions
l Replay control
l Data export
l Other functions
l Test control
and speed of logfile replay.
l Test display
l Replay control
l Data export
l Other functions
l Test control
l Test display
l Replay control
l Data export
l Other functions
l Data export
l Other functions
l Hardware
configuration
l System setting
l BTS configuration
l Project
configuration
Hardwar configuration
Hardware configuration
Add devices. Set different baud
rates for different devices and set
a unique port number ranging
from 1 to 32 for each device.
Mouse.ico
Hardware configuration
After adding a device, check whether
the device is successfully connected.
—A device can be used only when
the device is successfully connected.
You can select a device that is not in
use and delete it by pressing the
Delete key.
l Hardware
configuration
l System setting
l BTS configuration
l Project
configuration
System setting
p Test plan
p LOGMASK
p Event setting
p Alarm setting
System setting
p Test plan
p LOGMASK
p Event setting
p Alarm setting
System setting:
LOGMASK
System setting
p Test plan
p LOGMASK
p Event setting
p Alarm setting
System setting
p Test plan
p LOGMASK
p Event setting
p Alarm setting
System setting
p Test plan
p LOGMASK
p Event setting
p Alarm setting
l Hardware
configuration
l System setting
l BTS configuration
l Project
configuration
BTS configuration
BTS configuration
l Importing BTS
information
l Saving BTS information
l Hardware
configuration
l System setting
l BTS configuration
l Project
configuration
Project configuration
[ Suspending screen
display
l Capturing a window
l Technical
parameter view
l Signaling view
l Map view
l Event view
l Information view
p Main parameters
p Chart view
p List view
p Customized
template
… … …
p Main parameters
p Chart view
p List view
p Customized
template
p Main parameters
p Chart view
p List view
p Customized
template
p Main parameters
p Chart view
p List view
p Customized
template
l Technical
parameter view
l Signaling view
l Map view
l Event view
l Information view
Signaling view
Air interface messages can be
displayed and analyzed in a signaling
view. These messages include the
UMTS RRC and NAS signaling and
the GSM RR signaling. After a
complete signaling process is
performed, each unit of each
message can be a basis for locating
a problem.
l Technical
parameter view
l Signaling view
l Map view
l Event view
l Information view
Map view
[ Outdoor test
− Importing a
map
− Synchronizing
parameters
− Operating the
map
[ Indoor test
Map view
[ Outdoor test
− Importing a map
− Synchronizing parameters
[ Indoor test
Map view
[ Outdoor test
− Importing a map
− Synchronizing parameters
[ Indoor test
lZooming in a map
current location during the correction.
lUndoing: This operation is used to cancel the current
lZooming out a map
located point.
lZooming in or out a selected area on a
lRotating: This operation is performed to rotate a selected
map point during the static correction.
Map view
[ Outdoor test
[ Indoor test
Vertical test:
After starting a vertical test, you can click the
up-arrow or down-arrow button on the
navigation bar. If you click the up-arrow button,
the current location goes up by one floor. If you
click the down-arrow button, the current location
goes down by one floor. According to time, the
data between two points that indicate two
different floors is automatically displayed on the
map.
l Technical
parameter view
l Signaling view
l Map view
l Event view
l Information view
Event view
l Technical
parameter view
l Signaling view
l Map view
l Event view
l Information view
Information view
l Replay direction
l Replay speed
l Replay progress
l Replay progress
display
l Logfile locating
l Pause
Logfile export
Report generation
l Window arrangement
Window arrangement
The multiple-page mode is used for displaying data, and multiple windows can be opened at
the same time. Only one page, however, is displayed, and the other pages are hidden.
Multiple windows can be located on the same page, and the window arrangement function can
be performed to arrange these windows. By performing this function, you can use multiple
windows for displaying data at the same time. Thus, you can focus on the observation,
tracking, and comparison of test data.
Cascade Tile
l Question 1
l Question 2
For the Probe WCDMA, how many test modes are there in
terms of a chart view?
l Answer to question 1
l Answer to question 2