Professional Documents
Culture Documents
Titas Dėjus
11.19 · Vilnius Gediminas Technical University
10 Sec
Abstract
To design solutions for occupational safety at a construction site for the construction technology project,
an occupational hazard was assessed. Possible solutions for occupational safety depend on the
number of criteria such as hazardous factors from which workers must be protected; the number of
danger zones; architectural-design and structural solutions of a building; types of technical protection
measures, etc. A large set of solutions for occupational safety predetermines the number of respective
typical (or repeated) solutions, which are based on specific technical safety measures and are
applicable depending on a hazardous factor; besides, it determines systematisation of the solutions on
these grounds. It is suggested to use the Multiple Criteria Decision Making (MCDM) technique for
assessment and selection of appropriate solutions for occupational safety. The authors propose
formulating assessed alternatives from the typical solutions to ensure their quality and then apply the
entropy method for determining relative significances of evaluation criteria and, finally, use Weighted
Aggregated Sum Product Assessment (WASPAS) method for ranking of alternatives.
https://www.researchgate.net/publication/261580431_Assessment_of_health_and_safety_solutions_at_a_construction_site 1/22
29/7/2020 Assessment of health and safety solutions at a construction site | Request PDF
Request full-text
Advertisement
... Table 11. Normalized decision matrix for AGV system selection problem 0.3277 (7) 0.3438 (7) 0.3599 (7)
0.3760 (7) 0.3921 (7) 0.4083 (6) 0.4244 (6) 0.4405 (6) 0.4566 (6) 0.4727 (6) 0.3433 (6) 0.3539 (6) 0.3646
(6) 0.3752 (6) 0.3859 (6) 0.3965 (6) 0.4072 (7) 0.4178 (7) 0.4285 (7) 0.4391 (7) 0.4498 (7) ...
... Table 11. Normalized decision matrix for AGV system selection problem 0.3277 (7) 0.3438 (7) 0.3599 (7)
0.3760 (7) 0.3921 (7) 0.4083 (6) 0.4244 (6) 0.4405 (6) 0.4566 (6) 0.4727 (6) 0.3433 (6) 0.3539 (6) 0.3646
(6) 0.3752 (6) 0.3859 (6) 0.3965 (6) 0.4072 (7) 0.4178 (7) 0.4285 (7) 0.4391 (7) 0.4498 (7) ...
... Table 11. Normalized decision matrix for AGV system selection problem 0.3277 (7) 0.3438 (7) 0.3599 (7)
0.3760 (7) 0.3921 (7) 0.4083 (6) 0.4244 (6) 0.4405 (6) 0.4566 (6) 0.4727 (6) 0.3433 (6) 0.3539 (6) 0.3646
(6) 0.3752 (6) 0.3859 (6) 0.3965 (6) 0.4072 (7) 0.4178 (7) 0.4285 (7) 0.4391 (7) 0.4498 (7) ...
https://www.researchgate.net/publication/261580431_Assessment_of_health_and_safety_solutions_at_a_construction_site 2/22
29/7/2020 Assessment of health and safety solutions at a construction site | Request PDF
... A case study of ranking the facades for public and commercial buildings was presented and verification
of robustness of the method performed [25]. Searching the increase of ranking accuracy in a critical
situation, crisp WASPAS was applied for selecting the best occupational safety solution during construction
works [26] . In the current research the method is extended with interval-valued intuitionistic fuzzy numbers
and called WASPAS-IVIF. ...
... Extreme of the function can be found when derivative of Eq. (5) in regard to is equated to zero. Optimal
should be calculated for every alternative and may vary depending on ratio of 2 (Q i (1) )/ 2 (Q i (2) ) in
every particular case [25, 26] . ...
... There are different ways to specify the values ofx k ij : (1) the DM can directly estate the preferences
based on IVIF by determining a membership and a non-membership interval; (2) the DM can specify the
preferences based on crisp, fuzzy or intuitionistic fuzzy numbers. Then, the Bustince and Burillo theorem
[26] can be applied to transform the specified values to an associated IVIF value; and (3) the following
scale (Table 1) can be used to determine alternatives performance regard to criteria. These scales are
developed by applying Bustince and Burillo [34] theorem on an intuitionistic fuzzy scale which previously
extended and applied by Boran et al. [35]. ...
Extension of weighted aggregated sum product assessment with interval-valued intuitionistic fuzzy
numbers (WASPAS-IVIF)
Article
Nov 2014 · APPL SOFT COMPUT
Jurgita Antucheviciene · Seyed Hossein · Sh S Hashemi · Edmundas Kazimieras Zavadskas
View
... Table 11. Normalized decision matrix for AGV system selection problem 0.3277 (7) 0.3438 (7) 0.3599 (7)
0.3760 (7) 0.3921 (7) 0.4083 (6) 0.4244 (6) 0.4405 (6) 0.4566 (6) 0.4727 (6) 0.3433 (6) 0.3539 (6) 0.3646
(6) 0.3752 (6) 0.3859 (6) 0.3965 (6) 0.4072 (7) 0.4178 (7) 0.4285 (7) 0.4391 (7) 0.4498 (7) ...
... Table 11. Normalized decision matrix for AGV system selection problem 0.3277 (7) 0.3438 (7) 0.3599 (7)
0.3760 (7) 0.3921 (7) 0.4083 (6) 0.4244 (6) 0.4405 (6) 0.4566 (6) 0.4727 (6) 0.3433 (6) 0.3539 (6) 0.3646
(6) 0.3752 (6) 0.3859 (6) 0.3965 (6) 0.4072 (7) 0.4178 (7) 0.4285 (7) 0.4391 (7) 0.4498 (7) ...
... Table 11. Normalized decision matrix for AGV system selection problem 0.3277 (7) 0.3438 (7) 0.3599 (7)
0.3760 (7) 0.3921 (7) 0.4083 (6) 0.4244 (6) 0.4405 (6) 0.4566 (6) 0.4727 (6) 0.3433 (6) 0.3539 (6) 0.3646
(6) 0.3752 (6) 0.3859 (6) 0.3965 (6) 0.4072 (7) 0.4178 (7) 0.4285 (7) 0.4391 (7) 0.4498 (7) ...
https://www.researchgate.net/publication/261580431_Assessment_of_health_and_safety_solutions_at_a_construction_site 3/22
29/7/2020 Assessment of health and safety solutions at a construction site | Request PDF
... Robotics and remotely controlled manipulators have been invented and are being improved for
highsafety-risk construction activities Han et al. 2006). Information systems have been widely discussed for
managing massive multi-source heterogeneous data generated during construction and occupational
hazard on site was assessed, so that consistent and timely data can be shared between project
participants for effective safety collaborations Dėjus, Antuchevičienė 2013) . ...
... Information technology has been applied in a wide array of applications to provide solutions to
construction safety problems. Efforts made by researchers to assess the occupational safety (Dėjus,
Antuchevičienė 2013) , monitor performance of workers, equipment and construction environment, to
replace human operations with robots and to collaborate among themselves are vital in creating a safe-
working environment and in reducing casualties (Shin et al. 2014;Moon et al. 2014a;Ma et al. 2014;Kim
Yamada 2011;Shen, Zhu 2011;Maalek, Sadeghpour 2011;John, Ganah 2011;Guo et al. 2011;Golparvar-
Fard et al. 2011;Ding et al. 2011aDing et al. , 2011bChen et al. 2011;Aguilar, Hewage 2011;Yang et al.
2010;Yamamoto et al. 2010;Talmaki et al. 2010;Syachrani et al. 2010;Qi et al. 2010;Patel et al. 2010;Meng
et al. 2010aMeng et al. , 2010bHu et al. 2010aHu et al. , 2010bDobrzański, Pasternak 2009;Ding et al.
2010;Cheng et al. 2010;Zhang et al. 2009;Wang, Q. K., Wang, S. Q. 2009;Park et al. 2009;Lv, Zhu
2009;Teizer et al. 2008Teizer, Castro-Lacouture 2007;Teizer 2007;Li et al. 2007;Nuntasunti, Bernold
2006;Cho, Youn 2006). ...
... Table 2 Customer retention factor and their citation. Careless attitude (F 8 ) Dėjus and Antuchevičienė
(2013 ), Awa et al. (2016), Su et al. (2016), Padilla et al. (2017 important for everyone ( Idrees and Xinping,
2017). Customers are becoming more time conscious with little time to waste. ...
... Many such customers do not recognise any difference between an authorised workshop and local
technicians; therefore they do not come to the workshop on time. This is one of the factors for low
customer retention at workshops ( Dėjus and Antuchevičienė, 2013 ). Based on the above review, the
citations of each factor are summarized in Table 2 with support references as the foundation for AHP and
DEMATEL. ...
Measuring and improving customer retention at authorized automobile workshops after free services
Article
Jul 2017 · J Retailing Consum Serv
Anil Kumar · Sunil Luthra · Dinesh Kumar Khandelwal · Sukhdev Bhatia
View
https://www.researchgate.net/publication/261580431_Assessment_of_health_and_safety_solutions_at_a_construction_site 4/22
29/7/2020 Assessment of health and safety solutions at a construction site | Request PDF
... European country management capabilities within the construction sector in the time of crisis were
investigated, applying a proposed method determined via the entropy method (Susinskas et al., 2011 ).
Assessment and selection of appropriate solutions for occupational safety were classified as an MCDM
problem, and EWM was used to determine the relative significance of evaluation criteria ( Dejus and
Antucheviciene, 2013 ). ...
... However, in recent years, numerous studies have been carried out using MCDM methods to analyze
risks in construction industry [45]. Dejus and Antucheviciene [46] proposed MCDM technique for
assessment and selection of appropriate solutions for occupational safety. Furthermore, in construction
industry, Efe et al. [47] suggested an integrated intuitionistic fuzzy multi-criteria decision making method
and a linear programming for risk evaluation in three firms. ...
Application of Fuzzy DEMATEL Method for Analyzing Occupational Risks on Construction Sites
Article Full-text available
Nov 2017
Sukran Seker · Edmundas Kazimieras Zavadskas
... A model for comprehensive assessment of technologies applying AHP and Permutation method is
offered by Kildiene et al. (2014) . It is proposed to select the most suitable solution for ensuring safety at a
construction site applying a novel method WASPAS combining with Entropy ( Dejus, Antucheviciene
2013 ). The single application of ELECTRE III, PRO- METHEE II methods for selecting structural systems
can be observed in a paper of Balali et al. (2014). ...
https://www.researchgate.net/publication/261580431_Assessment_of_health_and_safety_solutions_at_a_construction_site 5/22
29/7/2020 Assessment of health and safety solutions at a construction site | Request PDF
... In this paper, application of a recent MCDM method, i.e. weighted aggregated sum product assessment
(WASPAS) method for determination of manufacturing process conditions in laser cutting considering
different technological, economical and quality criteria was discussed. Although it is a relatively new MCDM
method, the WASPAS method was already successfully used to solve many decision making problems
such as assessment of health and safety solutions at a construction site (Dejus & Antucheviciene, 2013) ,
improvement of daylighting in vernacular buildings (Siožinyte & Antucheviciene, 2013), selection of the
best place for shopping mall location with foresight perspective , selection and ranking of the feasible
location areas of wind farms and assessing the types of wind turbines (Bagocius et al., 2014), evaluation of
real-time intelligent sensors for structural health monitoring of bridges (Bitarafan et al., 2014),
determination of outsourcing strategies (Lashgari et al., 2014), identification and prioritization of suitable
regions for construction of expensive solar power plants (Vafaeipour et al., 2014). Unlike previous studies
related to the application of the WASPAS method for solving manufacturing MCDM problems (Chakraborty
& Zavadskas, 2014;Chakraborty et al., 2015a;Chakraborty et al., 2015b), this study is based on real
experimental data obtained through realization of Taguchi based experimentation of CO 2 laser cutting of
aluminum alloy. ...
... In order to enhance an accuracy of evaluation, Chakraborty and Zavadskas (2014) applied WASPAS
method in several manufacturing decision making problems. Dejus and Antucheviciene (2013) applied
WASPAS for multiple criteria assessment of safety technologies at a construction site. Cheng (2013) made
a comparison of technologies for the new materials development by applying fuzzy AHP. ...
A Hybrid MCDM Approach Based on Fuzzy ANP and Fuzzy TOPSIS for Technology Selection
Article
Dec 2015 · INFORMATICA-LITHUAN
Fahimeh Aliakbari Nouri · Saber Khalili · Jurgita Antucheviciene
https://www.researchgate.net/publication/261580431_Assessment_of_health_and_safety_solutions_at_a_construction_site 6/22
29/7/2020 Assessment of health and safety solutions at a construction site | Request PDF
... In this case, entropy can be used for determining the weights of criteria (Ye, 2010;Ghorbani, Bahrami &
Arabzad, 2012;Chen et al., 2014). However, the entropy method can be used in various fields Sliogeriene,
Turskis & Streimikiene, 2013; Dėjus, Antuchevičienė, 2013; Li, Liu & Li, 2014). The determination of the
weights of criteria begins with normalization of the initial decision-making matrix. ...
Is the evaluation of the students' values possible? An integrated approach to determining the weights of
students' personal goals using multiple-criteria methods
Article Full-text available
Nov 2016
Stanislav Dadelo · Edmundas Kazimieras Zavadskas · Ruta Dadeliene · Zenonas Turskis
... Results of Table 1 showed that, in fields of construction management, project management, safety and
risk management 37 articles (9.05%) have applied an MCDM approach and techniques. Construction
management, project management, safety and risk management involve several specific sub-fields, some
recent applications of MCDM approaches include: construction management (Zavadskas, Turskis,
Volvačiovas, & Kildiene, 2013;Zavadskas, Skibniewski, & Antucheviciene, 2014;Kanapeckiene et al.,
2010;Brauers, Kildienė, Zavadskas, & Kaklauskas, 2013;Gudienė, Banaitis, Podvezko, & Banaitienė,
2014) in field of project management (Buchanan & Vanderpooten, 2007;Mohammadi, Sadi, Nateghi,
Abdullah, & Skitmore, 2014;Zavadskas, Turskis, Tamošaitiene, & Marina, 2008), in the area of risk
management (Jiang, Hu, & Jin, 2007;Wabiri & Amusa, 2010), and in fields of safety (Liu, Mao, Li, & Yao,
2007;Wang, Qin, Li, & Chen, 2009;Chen, Jin, Qiu, & Chen, 2014; Dėjus & Antuchevičienė, 2013) . , and its
applications have been used more than other tools and approaches. ...
Multiple criteria decision-making techniques and their applications–a review of the literature from 2000 to
2014
Article Full-text available
Jan 2015 · EKON ISTRAZ
Abbas Mardani · Ahmad Jusoh · Khalil Md. Nor · Alireza Valipour
View
... In the probabilistic framework, Shannon entropy [62] is a well-known theory for uncertainty measure; it
has attracted much attention in real applications [63] [64] [65]. But Shannon entropy cannot be used
directly in the framework of Dempster-Shafer evidence theory, because a mass function in evidence theory
is a generalized probability assigned on the power set of the FOD. ...
https://www.researchgate.net/publication/261580431_Assessment_of_health_and_safety_solutions_at_a_construction_site 7/22
29/7/2020 Assessment of health and safety solutions at a construction site | Request PDF
... Zavadskas, Turskis, Antucheviciene and Zakarevicius [133], proposed this new method and proved that
this aggregated method performs more accurately than other approaches. Recently, a number of studies
conducted by using WASPAS method which is presented in the following scholars: Bagočius, Zavadskas
and Turskis [160] used WASPAS to select a deep-water port; Staniūnas, Medineckienė, Zavadskas and
Kalibatas [161] employed WASPAS for ecological-economic assessment of multi-dwelling house
modernization; Zavadskas, Antucheviciene, Šaparauskas and Turskis [162] used WASPAS to evaluate the
facade alternatives; Zavadskas, Antucheviciene, Saparauskas and Turskis [163] applied WASPAS for
verification of robustness of methods to assess the alternative solutions; Bitarafan, Zolfani, Arefi,
Zavadskas and Mahmoudzadeh [164] used WASPAS to evaluate of real-time intelligent sensors for
structural health monitoring of bridges; Dėjus and Antuchevičienė [165] used it to assess health and
safety solutions on the construction site; and Hashemkhani Zolfani, Aghdaie, Derakhti, Zavadskas and
Morshed Varzandeh [166] applied WASPAS to decision making with respect to business issues in the
foresight perspective. The methodology of WASPAS technique is presented in Fig. 2. ...
A systematic review and meta-Analysis of SWARA and WASPAS methods: Theory and applications with
recent fuzzy developments
Article Full-text available
Mar 2017 · APPL SOFT COMPUT
Mehrbakhsh Nilashi · Norhayati Zakuan · Assoc Prof. Dr. Othman Ibrahim · Abbas Mardani
... If opt value is min. All the researches based on the WASPAS method up to now are described in several
references as below: Zavadskas et al. (2012) in developing WASPAS as a new methodology;
Hashemkhani Zolfani et al. (2013c) in decision making on business issues with foresight perspective;
Dejus and Antucheviciene (2013) in assessment of health and safety solutions at a construction site;
Šiožinytė and Antuchevicienė (2013) ...
A hybrid MADM analysis in evaluating process of chemical wastewater purification regarding to advance
oxidation processes
Article Full-text available
Jul 2017 · J ENVIRON ENG LANDSC
https://www.researchgate.net/publication/261580431_Assessment_of_health_and_safety_solutions_at_a_construction_site 8/22
29/7/2020 Assessment of health and safety solutions at a construction site | Request PDF
... European country management capabilities within the construction sector in the time of crisis were
investigated applying a proposed method determined via entropy method (Susinskas et al., 2011).
Assessment and selection of appropriate solutions for occupational safety was classified as MCDM
problem and EWM was used to determine relative significances of evaluation criteria (Dejus and
Antucheviciene, 2013) . ...
Comprehensive evaluation of high rocky slope safety through an integrated analytic hierarchy process
and extension matter model
Article Full-text available
Feb 2016
H. Z. Su · M. Yang · Z. P. Wen
... It has now been applied for solving MCDM problems for increasing ranking accuracy and it has the
capability to reach the highest accuracy of estimation. Till date, WASPAS method has limited successful
applications in location selection (Hashemkhani Zolfani et al., 2013), civil engineering domain (Dėjus &
Antuchevičienė, 2013; Staniūnas et al., 2013;Šiožinyte & Antuchevičiene, 2013), port site selection
(Bagočius et al., 2013) and manufacturing decision-making (Chakraborty & Zavadskas, 2014). ...
A study on the ranking performance of some MCDM methods for industrial robot selection problems
Article Full-text available
Jun 2016
Prasad Karande · Edmundas Kazimieras Zavadskas · Shankar Chakraborty
... Results of Table 1 showed that, in fields of construction management, project management, safety and
risk management 37 articles (9.05%) have applied an MCDM approach and techniques. Construction
management, project management, safety and risk management involve several specific sub-fields, some
recent applications of MCDM approaches include: construction management (Zavadskas, Turskis,
Volvačiovas, & Kildiene, 2013;Zavadskas, Skibniewski, & Antucheviciene, 2014;Kanapeckiene et al.,
2010;Brauers, Kildienė, Zavadskas, & Kaklauskas, 2013;Gudienė, Banaitis, Podvezko, & Banaitienė,
https://www.researchgate.net/publication/261580431_Assessment_of_health_and_safety_solutions_at_a_construction_site 9/22
29/7/2020 Assessment of health and safety solutions at a construction site | Request PDF
2014) in field of project management (Buchanan & Vanderpooten, 2007;Mohammadi, Sadi, Nateghi,
Abdullah, & Skitmore, 2014;Zavadskas, Turskis, Tamošaitiene, & Marina, 2008), in the area of risk
management (Jiang, Hu, & Jin, 2007;Wabiri & Amusa, 2010), and in fields of safety (Liu, Mao, Li, & Yao,
2007;Wang, Qin, Li, & Chen, 2009;Chen, Jin, Qiu, & Chen, 2014; Dėjus & Antuchevičienė, 2013) .
(Shidpour et al., 2013) 2013 Utilised research ...
Multiple Criteria Decision Making Techniques and Its Applications– A Review of the Literature from 2000
to 2014
Article Full-text available
Oct 2015 · EKON ISTRAZ
Abbas Mardani · Ahmad Jusoh · Khalil Md. Nor · Alireza Valipour
... Applications and developments of WASPAS method have been reported in many studies. It was used
for assessment and selection of appropriate solutions for occupational safety (Dejus, Antucheviciene
2013) . Capability of WASPAS for exact ranking of alternatives was shown by solving eight manufacturing
selection problems (Chakraborty, Zavadskas 2014). ...
Developing WASPAS-RTB method for range target-based criteria: toward selection for robust design
Article Full-text available
Jul 2018
Ali Jahan
... It has been applied for solving MCDM problems for increasing ranking accuracy and it has the capability
to reach the highest accuracy of estimation. Till date, WASPAS method has very limited applications, only
in location selection [14], civil engineering domain [15] [16][17], port site selection [18] and manufacturing
decision-making [19]. ...
https://www.researchgate.net/publication/261580431_Assessment_of_health_and_safety_solutions_at_a_construction_site 10/22
29/7/2020 Assessment of health and safety solutions at a construction site | Request PDF
... This desire transforms the decision making problem into a Multi-Objective Decision-Making (MODM)
problem or a Multi-Attribute Decision-Making (MADM) problem. These groups of problems all encompass
one category defined as Multi-Criteria Decision-Making (MCDM) problems (Nutt 2000;Farahani et al.
2010;Brauers, Zavadskas 2008;Rezaeiniya et al. 2012;Hashemkhani Zolfani et al. 2013aTamošaitienė et
al. 2013; Dėjus, Antuchevičienė 2013) . ...
... WASPAS enables to reach the highest accuracy of estimation applying suggested methodology for
optimization of weighted aggregated function. It was successfully applied for decision making in civil
engineering when ranking strategies for construction works [25, 26] , house modernization [27,28], or
selecting the most appropriate location [29]. Suppose that a given MCDM problem is defined using m
alternatives (journals covered by the analysis) and n decision criteria, applied for ranking the journals. ...
ACME 231
Data
Feb 2015
Miroslaw J. Skibniewski · Jurgita Antucheviciene · Edmundas Kazimieras Zavadskas
View
https://www.researchgate.net/publication/261580431_Assessment_of_health_and_safety_solutions_at_a_construction_site 11/22
29/7/2020 Assessment of health and safety solutions at a construction site | Request PDF
... Bas (2013) integrated SWOT–FTOPSIS methodology with AHP to propose a structure for prioritization
for each factor within the SWOT groups, meanwhile utilizing fuzzy TOPSIS they evaluated the electricity
supply chain with respect to the SWOT factors. Dėjus and Antuchevičienė (2013) using MCDM
approaches aimed to evaluate the possible solutions for occupational safety. For a given construction
technology project all the hazards were identified and based on the related criteria for each hazard all
solutions were developed. ...
The Formulation of Organizational Strategies through Integration of Freeman Model, SWOT, and Fuzzy
MCDM Methods: A Case Study of Oil Industry
Article
Dec 2014 · TRANSFORM BUS ECON
Ahmad Esmaeili · Reza Ahmadi kahnali · Reza Rostamzadeh · Akbar Sepahvand
View
A hybrid model based on fuzzy AHP and fuzzy WASPAS for construction site selection
https://www.researchgate.net/publication/261580431_Assessment_of_health_and_safety_solutions_at_a_construction_site 12/22
29/7/2020 Assessment of health and safety solutions at a construction site | Request PDF
Article
Oct 2015 · INT J COMPUT COMMUN
Zenonas Turskis · Natalja Kosareva · Edmundas Kazimieras Zavadskas · Jurgita Antucheviciene
Optimising the Elements of a Construction Health and Safety (H&S) Programme and Audit System
Article Full-text available
Dec 2015
John Smallwood
Selecting a Contractor by Using a Novel Method for Multiple Attribute Analysis: Weighted Aggregated
Sum Product Assessment with Grey Values (WASPAS-G)
Article
Dec 2015
Edmundas Kazimieras Zavadskas · Zenonas Turskis · Jurgita Antucheviciene
2078-4290-1-PB+++
Data Full-text available
Jan 2016
Zenonas Turskis · Edmundas Kazimieras Zavadskas · Jurgita Antucheviciene · Natalja Kosareva
View
Evaluation of real-time intelligent sensors for structural health monitoring of bridges based on SWARA-
WASPAS; a case in Iran
Article Full-text available
Dec 2014
Mahdi Bitarafan · Shahin Lale Arefi · Amir Mahmoudzadeh · Sarfaraz Hashemkhani Zolfani
https://www.researchgate.net/publication/261580431_Assessment_of_health_and_safety_solutions_at_a_construction_site 13/22
29/7/2020 Assessment of health and safety solutions at a construction site | Request PDF
A novel entropy proposition for spherical fuzzy sets and its application in multiple attribute decision‐
making
Article
Jul 2020 · INT J INTELL SYST
Ali Aydoğdu · Sait Gül
View
Investigation of machinability criteria during micro-abrasive finishing of SUS-304L steel using fuzzy
combined with WASPAS approach
Article
Mar 2020 · J BRAZ SOC MECH SCI
Rahul Sharma · Swastik Pradhan
A novel approach for classification of occupational health and safety measures based on their
https://www.researchgate.net/publication/261580431_Assessment_of_health_and_safety_solutions_at_a_construction_site 14/22
29/7/2020 Assessment of health and safety solutions at a construction site | Request PDF
View
Human risk assessment of Panchet Dam in India using TOPSIS and WASPAS Multi-Criteria Decision-
Making (MCDM) methods
Article Full-text available
Jun 2019
Sumanta Bid · Giyasuddin Siddique
Determining the utility in management by using multi-criteria decision support tools: a review
Article
Sep 2018 · EKON ISTRAZ
Ungku Norulkamar Ungku Ahmad · Andrzej Magruk · Abbas Mardani · Ahmad Jusoh
Parametric Optimization of Micro-EDM Process during Micro-hole Machining on Ti-6Al-4V using WASPAS
https://www.researchgate.net/publication/261580431_Assessment_of_health_and_safety_solutions_at_a_construction_site 15/22
29/7/2020 Assessment of health and safety solutions at a construction site | Request PDF
Method
Article Full-text available
Jun 2018
A. P. Tiwary · Partha Protim Das · S. Chakraborty · B. Bhattacharyya
A decision support system for agricultural machines and equipment selection: A case study on olive
harvester machines
Article Full-text available
May 2018 · COMPUT ELECTRON AGR
Ashkan Hafezalkotob · Aida Hami-Dindar · Naghmeh Rabie · Arian Hafezalkotob
The Effectiveness of Health and Safety Training and Its Impact on Construction Workers’ Attitudes, and
Perceptions
Chapter
Mar 2018
Tafadzwa Mushayi · Claire Deacon · John Smallwood
https://www.researchgate.net/publication/261580431_Assessment_of_health_and_safety_solutions_at_a_construction_site 16/22
29/7/2020 Assessment of health and safety solutions at a construction site | Request PDF
An approach of evaluation and mechanism study on the high and steep rock slope in water conservancy
project
Article
May 2017 · COMPUT CONCRETE
Huaizhi Su · Meng Yang · Zhiping Wen
Selection of portable hard disk drive based upon weighted aggregated sum product assessment method:
A case of Indian market
Article Full-text available
Jun 2020 · MEAS CONTROL-UK
Raman Kumar · Abhishek Bhattacherjee · Angad Deep Singh · Catalin Pruncu
Multiple Nash Equilibriums and evaluation of strategies. New application of MCDM methods
Article Full-text available
Mar 2015 · J BUS ECON MANAG
Sarfaraz Hashemkhani Zolfani · Reza Maknoon · Edmundas Kazimieras Zavadskas
Show more
Recommendations
https://www.researchgate.net/publication/261580431_Assessment_of_health_and_safety_solutions_at_a_construction_site 17/22
29/7/2020 Assessment of health and safety solutions at a construction site | Request PDF
Project
View project
Project
View project
https://www.researchgate.net/publication/261580431_Assessment_of_health_and_safety_solutions_at_a_construction_site 18/22
29/7/2020 Assessment of health and safety solutions at a construction site | Request PDF
Project
View project
Project
Co-Researcher
Akbar Sepahvand · Reza Rostamzadeh · Ahmad Esmaeili · [...] ·
View project
https://www.researchgate.net/publication/261580431_Assessment_of_health_and_safety_solutions_at_a_construction_site 19/22
29/7/2020 Assessment of health and safety solutions at a construction site | Request PDF
Article
Read more
Article
Re: Robinson, AE (1989): Standard setting and protection of human health and safety. Am J Ind Med 15...
January 1989 · American Journal of Industrial Medicine
Read more
https://www.researchgate.net/publication/261580431_Assessment_of_health_and_safety_solutions_at_a_construction_site 20/22
29/7/2020 Assessment of health and safety solutions at a construction site | Request PDF
Article
There is a multitude of norms and general guidelines relevant to machine safety. Two possibilities are discussed which allow a systematic analysis
of hazards concerning processes, process steps and machines down to their components, and which allow appropriate measures to be defined. It
concerns the so-called FMEA (Fehler-Mo¨glichkeits- und Einfluss-Analyse = Fault Occurrence and Influence ... [Show full abstract]
Read more
Article
3 pp. By following a few simple measures, you can help protect yourself and your family from food-borne illness caused by harmful bacteria.
Read more
Discover more
https://www.researchgate.net/publication/261580431_Assessment_of_health_and_safety_solutions_at_a_construction_site 21/22
29/7/2020 Assessment of health and safety solutions at a construction site | Request PDF
© 2008-2020 ResearchGate GmbH. All rights reserved. Terms · Privacy · Copyright · Imprint
https://www.researchgate.net/publication/261580431_Assessment_of_health_and_safety_solutions_at_a_construction_site 22/22