Professional Documents
Culture Documents
Crayon Puppet
by andruppets on May 30, 2013
Table of Contents
Crayon Puppet . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Step 4: Finishing Up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Related Instructables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Advertisements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Comments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
http://www.instructables.com/id/Crayon-Puppet/
Author:andruppets Andrew Olsen
I love puppets! Subscribe on my website and follow me on instructables and I'll give you a 20% off coupon on one select ready made puppet!
http://www.andruppets.com/
http://www.instructables.com/id/Crayon-Puppet/
http://www.instructables.com/id/Crayon-Puppet/
http://www.instructables.com/id/Crayon-Puppet/
Step 2: Mouth plate
Now take the foam board and trace 2 half circle the will fit the diameter of the skull. Leave a half inch in between the two boards and place duct tape on over the gap.
Now bend over a table and place another piece of tape. Trim the edges. Now cut small rectangles out of foam and glue together to make small tubes for your fingers to fit
through. Put a small amount of contact cement on the foam board and put the finger tubes down. Let dry. Now cover the whole front of the foam board with contact
cement and put the red fleece over it. Let dry. Glue the excess fabric to the rear of the mouth plate. Put glue on the rim of the top of the board and attach to the skull. Let
dry.
http://www.instructables.com/id/Crayon-Puppet/
http://www.instructables.com/id/Crayon-Puppet/
http://www.instructables.com/id/Crayon-Puppet/
Step 3: The Body
Trace a large rectangle of foam that will match the diameter if the skull and the length of about the Heath of the skull times 2. Glue the long sides together. Cut a piece of
fabric from your pattern but add a 3" seam allowance vertically and 1" horizontally. Now sew the long ends together and fit it over the puppet.
http://www.instructables.com/id/Crayon-Puppet/
http://www.instructables.com/id/Crayon-Puppet/
Step 4: Finishing Up
Now sew or glue the upper and lower jaw to the mouth plate. And sew the back of the head using the whip stitch. Sew the excess fabric underneath the puppet the inside
body. Now cut small slits to attach the eyes. Place the eyes in the head and put the plastic washer on the back. Cut a thin strip of black felt and sew The ends. Now hand
sew it on to the puppet body. Your finished! You made a crayon puppet. You can make these as big or small as you like. Visit my website: Andruppets.com
http://www.instructables.com/id/Crayon-Puppet/
http://www.instructables.com/id/Crayon-Puppet/
Related Instructables
Advertisements
Comments
1 comments Add Comment
http://www.instructables.com/id/Crayon-Puppet/