Professional Documents
Culture Documents
WindLoadCalc-01 - Copy 40X40
WindLoadCalc-01 - Copy 40X40
Results 1
1
Clauses Ao>1.1Aoi Ao>4 or 0.01 Ag Aoi/Agi<0.2 Building 1
Area 1 = NO NO OK Enclosed 1
Area 2 = NO NO OK Enclosed 1
Area 3 = NO OK OK Enclosed 1
Area 4 = NO OK OK Enclosed
Area 5 = NO NO OK Enclosed
Area 6 = NO NO OK Enclosed
1 03/28/2022 04:56:37
INPUT &
OUTPUT SHEET
Input Data:
Wind
B
Load Data:
Roof Dead Load:
Purlin Load = 1 Psf L= 40.00
Roof Sheeting = 1 Psf
Collateral Load = 2 Psf Plan
Accessories = 1 Psf
Roof Live Load:
Area = 800 Sft
Roof Live Load = 12 PSF :-MBMA-2006
2 03/28/2022 04:56:37
Main Frame Design Loads: Second
First h <=
Conditions: h <= 60' Min(L,B)
Yes, O.K. Yes, O.K.
I
II If h < 15 then: Kh = 2.01*(15/zg)^(2/a) (Table 6-3, Case 1b)
III If h >= 15 then: Kh = 2.01*(z/zg)^(2/a) (Table 6-3, Case 1b)
IV a= 9.50 (Table 6-2)
B zg = 900 (Table 6-2)
C Kh = 0.86 (Kh = Kz evaluated at z = h)
D I= 1.15 (Table 6-1) (Importance factor)
Gable Velocity Pressure: qz = 0.00256*Kz*Kzt*Kd*V^2*I (Sect. 6.5.10, Eq. 6-15)
Monoslope qh = 13.78 psf qh = 0.00256*Kh*Kzt*Kd*V^2*I (qz evaluated at z = h)
Y
N qh = 13.78 Psf
Part. Closed
Closed Load Transverse Dir. PLF (For Staad)
Open Internal Frame
Wind Load Roof Dead Roof Live Floor Dead Floor Live
Surface Co-efficients Loads (PLF) Load Load MB MB
(w/ +GCpi) (w/ -GCpi) (w/ +GCpi) (w/ -GCpi) Plf Plf Plf Plf
Zone 1 0.23 0.59 62 162 -1000 -1200
Zone 2 -0.87 -0.51 240 141 0 0
Zone 3 -0.56 -0.20 153 54 0 0
Zone 4 -0.48 -0.12 131 32 -60 -240 0 0
Zone 5 -0.63 -0.27 174 74 0 0
Zone 6 -0.63 -0.27 174 74
Status 20.00 ft Half of Building
End Wall
Zone 1E 0.44 0.80 55 104 -500 -600
Zone 2E -1.25 -0.89 162 112 0 0
Zone 3E -0.72 -0.36 94 45 -30 -120 0 0
Zone 4E -0.62 -0.26 81 32 0 0
Status 20.00 ft Half of Building 0 0
a= 4.0 ft
Total Horizontal Force = 2043 Lbs X- Dir.
2043 Lbs Opposite
Joist Loads
3 03/28/2022 04:56:37
As a Wall Member
Internal Girts Contributory Area
a. The Average of Two Adjacent Tributory Widths 4.00 0.00 2.00 ft
b. Span (Bay Spacing) divided by 3 20.00 3.00 6.67 ft
Inward Pressure
All Zones = 24.84 Plf
4 03/28/2022 04:56:37
Girts (Wall Components) Design Loads:
5 03/28/2022 04:56:37
End Wall Column Design Loads:
Zone 4 = Interior
Zone 5 = Corner a= 4.0 ft
6 03/28/2022 04:56:37
X-Bracings
X-Bracing Data
No. of Wind Column Bays = 6 Nos. Wind Column Spacing = 6.67 ft
Steel Rope Yeild Strength = 50 ksi Length of Cable = 21.1 ft
Dia Of Rope = 12 mm Braced Bays = 4 Nos.
Horizontal Component = 355 Lbs
Vertical Reaction = 284 Lbs
Forces in Roof Nos. of Ropes Dia of Rope Used
SR.<=1
Lbs Nos. mm
355 1 12 0.20
293 1 12 0.18
166 1 12 0.14
34 1 12 0.06
0 1 12 0.00
0 1 12 0.00
0 1 12 0.00
0 1 12 0.00
0 1 12 0.00
0 1 12 0.00
0 1 12 0.00
0 1 12 0.00
0 1 12 0.00
0 1 12 0.00
0 1 12 0.00
0 1 12 0.00
7 03/28/2022 04:56:37
Cranes Data & Load Calculation
8 03/28/2022 04:56:37
WIND LOADING ANALYSIS - Main Wind-Force Resisting System
Input Data:
Wall and Roof End Zone Widths 'a' and '2*a' (Fig. 6-10):
a= 4.00 ft.
2*a = 8.00 ft.
9 03/28/2022 04:56:37
MWFRS Wind Load for Transverse Direction MWFRS Wind Load for Longitudinal Direction
Surface GCpf p = Net Pressures (psf) Surface *GCpf p = Net Pressures (psf)
(w/ +GCpi) (w/ -GCpi) (w/ +GCpi) (w/ -GCpi)
Zone 1 0.41 3.12 8.08 Zone 1 0.40 3.03 7.99
Zone 2 -0.69 -11.99 -7.03 Zone 2 -0.69 -11.99 -7.03
Zone 3 -0.38 -7.65 -2.69 Zone 3 -0.37 -7.58 -2.62
Zone 4 -0.30 -6.57 -1.61 Zone 4 -0.29 -6.48 -1.52
Zone 5 -0.45 -8.68 -3.72 Zone 5 -0.45 -8.68 -3.72
Zone 6 -0.45 -8.68 -3.72 Zone 6 -0.45 -8.68 -3.72
Zone 1E 0.62 6.05 11.01 Zone 1E 0.61 5.93 10.89
Zone 2E -1.07 -17.23 -12.27 Zone 2E -1.07 -17.23 -12.27
Zone 3E -0.54 -9.89 -4.93 Zone 3E -0.53 -9.78 -4.82
Zone 4E -0.44 -8.54 -3.58 Zone 4E -0.43 -8.41 -3.45
10 03/28/2022 04:56:37
Low-Rise
Buildings
h <= 60'
11 03/28/2022 04:56:37
CALCULATIONS:
Length of Roof Zones 2/2E for Transverse and Long. Cases when GCpf is Negative in Roof Zones 2/2E:
For Transverse Case: For Longitudinal Case:
0.5*L = 20.00 0.5*B = 20.00
2.5*he = 40.00 2.5*he = 40.00
Use = 20.00 Use = 20.00
12 03/28/2022 04:56:37
MWFRS Wind Load Factor for Trans. Direction MWFRS Wind Load Factor for Long. Direction
Surface GCpf p = Net Pressures (psf) Surface *GCpf p = Net Pressures (psf)
(w/ +GCpi) (w/ -GCpi) (w/ +GCpi) (w/ -GCpi)
Zone 1 0.41 0.23 0.59 Zone 1 0.40 0.22 0.58
Zone 2 -0.69 -0.87 -0.51 Zone 2 -0.69 -0.87 -0.51
Zone 3 -0.38 -0.56 -0.20 Zone 3 -0.37 -0.55 -0.19
Zone 4 -0.30 -0.48 -0.12 Zone 4 -0.29 -0.47 -0.11
Zone 5 -0.45 -0.63 -0.27 Zone 5 -0.45 -0.63 -0.27
Zone 6 -0.45 -0.63 -0.27 Zone 6 -0.45 -0.63 -0.27
Zone 1E 0.62 0.44 0.80 Zone 1E 0.61 0.43 0.79
Zone 2E -1.07 -1.25 -0.89 Zone 2E -1.07 -1.25 -0.89
Zone 3E -0.54 -0.72 -0.36 Zone 3E -0.53 -0.71 -0.35
Zone 4E -0.44 -0.62 -0.26 Zone 4E -0.43 -0.61 -0.25
For Analysis Only
Pressure PLF Pressure PLF as per STAAD
Surface Transverse Dir. Longitudinal Dir. Transverse Dir. Longitudinal Dir.
(w/ +GCpi)(w/ -GCpi) (w/ +GCpi) (w/ -GCpi) (w/ +GCpi) (w/ -GCpi) (w/ +GCpi) (w/ -GCpi)
Zone 1 62 162 30 160 62 162 30 160
Zone 2 -240 -141 -240 -141 240 141 240 141
Zone 3 -153 -54 -152 -52 153 54 152 52
Zone 4 -131 -32 -130 -30 131 32 130 30
Zone 5 -174 -74 -174 -74 174 74 174 74
Zone 6 -174 -74 -174 -74 174 74 174 74
Zone 1E 55 104 33 104 55 104 33 104
Zone 2E -162 -112 -162 -112 162 112 162 112
Zone 3E -94 -45 -94 -45 94 45 94 45
Zone 4E -81 -32 -81 -32 81 32 81 32
13 03/28/2022 04:56:37
"ASCE705W.xls" Program
Version 1.2
If z <= 15 then: Kz = 2.01*(15/zg)^(2/a) , If z > 15 then: Kz = 2.01*(z/zg)^(2/a) (Table 6-3, Case 2a)
a= 9.50 zg = 900 (Table 6-2)
Kh = 0.86 (Kh = Kz evaluated at z = h)
I= 1.15 (Table 6-1) (Importance factor)
Velocity Pressure: qz = 0.00256*Kz*Kzt*Kd*V^2*I (Sect. 6.5.10, Eq. 6-15)
qh = 13.78 psf qh = 0.00256*Kh*Kzt*Kd*V^2*I (qz evaluated at z = h)
Ratio h/L = 0.400 freq., f = 6.250 hz. (f >= 1, Rigid structure)
Gust Factor, G = 0.850 (Sect. 6.5.8)
Design Net External Wind Pressures (Sect. 6.5.12.2):
p = qz*G*Cp - qi*(+/-GCpi) for windward wall (psf), where: qi =qh (Eq. 6-17, Sect. 6.5.12.2.1)
p = qh*G*Cp - qi*(+/-GCpi) for leeward wall, sidewalls, and roof (psf), where: qi = qh (Sect. 6.5.12.2.1)
14 of 71 03/28/2022 04:56:37
"ASCE705W.xls" Program
Version 1.2
Normal to Ridge Wind Load Tabulation for MWFRS - Buildings of Any Height
Surface z Kz qz Cp p = Net Design Press. (psf)
(ft.) (psf) (w/ +GCpi) (w/ -GCpi)
Windward Wall 0 0.85 13.60 0.80 6.76 11.73
15.00 0.85 13.60 0.80 6.76 11.73
For z = hr: 18.00 0.88 14.13 0.80 7.13 12.09
Notes: 1. (+) and (-) signs signify wind pressures acting toward & away from respective surfaces.
2. Per Code Section 6.1.4.1, the minimum wind load for MWFRS shall not be less than 10 psf.
3. References : a. ASCE 7-02, "Minimum Design Loads for Buildings and Other Structures".
b. "Guide to the Use of the Wind Load Provisions of ASCE 7-02"
by: Kishor C. Mehta and James M. Delahay (2004).
4. Roof zone #1 is applied for horizontal distance of 0 to h/2 from windward edge.
5. Roof zone #2 is applied for horizontal distance of h/2 to h from windward edge.
6. Roof zone #3 is applied for horizontal distance of h to 2*h from windward edge.
7. Roof zone #4 is applied for horizontal distance of > 2*h from windward edge.
15 of 71 03/28/2022 04:56:37
"ASCE705W.xls" Program
Version 1.2
Parameters Used in Both Item #2 and Item #3 Calculations (from Table 6-2):
a^ = 0.105
b^ = 1.00
a(bar) = 0.154
b(bar) = 0.65
c= 0.20
l= 500 ft.
e(bar) = 0.200
z(min) = 15 ft.
16 of 71 03/28/2022 04:56:37
"ASCE705W.xls" Program
Version 1.2
Figure 6-9 - Design Wind Load Cases of MWFRS for Buildings of All Heights
Case 1: Full design wind pressure acting on the projected area perpendicular to each principal axis of
the structure, considered separately along each principal axis.
Case 2: Three quarters of the design wind pressure acting on the projected area perpendicular to each
principal axis of the structure in conjunction with a torsional moment as shown, considered
separately for each principal axis.
Case 3: Wind pressure as defined in Case 1, but considered to act simultaneously at 75% of the
specified value.
Case 4: Wind pressure as defined in Case 2, but considered to act simultaneously at 75% of the
specified value.
Notes: 1. Design wind pressures for windward (Pw) and leeward (PL) faces shall be determined in
accordance with the provisions of Section 6.5.12.2.1 and 6.5.12.2.3 as applicable for buildings
of all heights.
2. Above diagrams show plan views of building.
3. Notation:
Pwx, Pwy = Windward face pressure acting in the X, Y principal axis, respectively.
PLx, PLy = Leeward face pressure acting in the X, Y principal axis, respectively.
e (ex, ey) = Eccentricity for the X, Y principal axis of the structure, respectively.
MT = Torsional moment per unit height acting about a vertical axis of the building.
17 of 71 03/28/2022 04:56:37
WIND LOADING ANALYSIS - Wall Components and Cladding
Per ASCE 7-05 Code for Buildings of Any Height
Using Method 2: Analytical Procedure (Section 6.5)
Job Name: ABCON ware house Subject: II
Job Number: MT-Q-****** Originator: Samad Checker: Aslam
IV
Input Data: B
C
Wind Speed, V = 80 mph (Wind Map, Figure 6-1) D
Bldg. Classification = III (Table 1-1 Occupancy Category) Gable
Exposure Category = C (Sect. 6.5.6) B
Monoslope
Ridge Height, hr = 18.00 ft. (hr >= he) Y
Eave Height, he = 16.00 ft. (he <= hr) N
Building Width = 40.00 ft. (Normal to Building Ridge) Girt
Building Length = 40.00 ft. (Parallel to Building Ridge) Siding
L
Roof Type = Gable (Gable or Monoslope) Wall
Topo. Factor, Kzt = 1.00 (Sect. 6.5.7 & Figure 6-4) Plan Fastener
Direct. Factor, Kd = 0.85 (Table 6-4)
Enclosed? (Y/N) Y (Sect. 6.2 & Figure 6-5)
Hurricane Region? N qo
Component Name = Girt (Girt, Siding, Wall, or Fastener) hr
h
Effective Area, Ae = 133.33 ft.^2 (Area Tributary to C&C) h
e
If z <= 15 then: Kz = 2.01*(15/zg)^(2/a) , If z > 15 then: Kz = 2.01*(z/zg)^(2/a) (Table 6-3, Case 1a)
a= 9.50 (Table 6-2)
zg = 900 (Table 6-2)
Kh = 0.86 (Kh = Kz evaluated at z = h)
I= 1.15 (Table 6-1) (Importance factor)
Velocity Pressure: qz = 0.00256*Kz*Kzt*Kd*V^2*I (Sect. 6.5.10, Eq. 6-15)
qh = 13.78 psf qh = 0.00256*Kh*Kzt*Kd*V^2*I (qz evaluated at z = h)
18 03/28/2022 04:56:37
Wind Load Tabulation for Wall Components & Cladding
Component z Kh qh p = Net Design Pressures (psf)
(ft.) (psf) Zone 4 (+) Zone 4 (-) Zone 5 (+) Zone 5 (-)
Girt 0 0.86 13.78 12.42 -13.66 12.42 -14.92
15.00 0.86 13.78 12.42 -13.66 12.42 -14.92
For z = hr: 18.00 0.86 13.78 12.42 -13.66 12.42 -14.92
Notes: 1. (+) and (-) signs signify wind pressures acting toward & away from respective surfaces.
2. Width of Zone 5 (end zones), 'a' = 4.00 ft.
3. Per Code Section 6.1.4.2, the minimum wind load for C&C shall not be less than 10 psf.
4. References : a. ASCE 7-02, "Minimum Design Loads for Buildings and Other Structures".
b. "Guide to the Use of the Wind Load Provisions of ASCE 7-02"
by: Kishor C. Mehta and James M. Delahay (2004).
19 03/28/2022 04:56:37
Wall Components and Cladding:
20 03/28/2022 04:56:37
CALCULATIONS:
Width 'a' for Zone 5 forWidth 'a' for Zone 5 for h > 60':
Lesser of L or B: 40.00 er of L or B: N.A.
0.1*(L or B): 4.00 0.1*(L or B): N.A.
Compare to 0.4*h: 4.00 mpare to 3': N.A.
Compare to .04*(L, B): 4.00 Use 'a' = N.A.
Compare to 3': 4.00
Use 'a' = 4.00
21 03/28/2022 04:56:37
WIND LOADING ANALYSIS - End Wall Columns
Components and Cladding
Per ASCE 7-05 Code for Buildings of Any Height
Using Method 2: Analytical Procedure (Section 6.5)
Job Name: ABCON ware house Subject: II
Job Number: MT-Q-****** Originator: Samad Checker: Aslam
IV
Input Data: B
C
Wind Speed, V = 80 mph (Wind Map, Figure 6-1) D
Bldg. Classification = III (Table 1-1 Occupancy Category) Gable
Exposure Category = C (Sect. 6.5.6) B
Monoslope
Ridge Height, hr = 18.00 ft. (hr >= he) Y
Eave Height, he = 16.00 ft. (he <= hr) N
Building Width = 40.00 ft. (Normal to Building Ridge) Girt
Building Length = 40.00 ft. (Parallel to Building Ridge) Siding
L
Roof Type = Gable (Gable or Monoslope) Wall
Topo. Factor, Kzt = 1.00 (Sect. 6.5.7 & Figure 6-4) Plan Fastener
Direct. Factor, Kd = 0.85 (Table 6-4) Compare to 3':
Enclosed? (Y/N) Y (Sect. 6.2 & Figure 6-5) Use 'a' =
Hurricane Region? N qo
Component Name = Wall (Girt, Siding, Wall, or Fastener) hr
h
No. of Wind Columns = 6 Nos. +GCpi Coef. (PIP) h=
-GCpi Coef. (NIP) e=
L
Resulting Parameters and Coefficients: Elevation
a=
Wind Column Spacing = 6.67 ft zg =
Roof Angle, q = 5.71 deg. Slope = 1: 10.00 Kh =
Mean Roof Ht., h = 16.00 ft. (h = he, for roof angle <=10 deg.) I=
qh =
Wall External Pressure Coefficients, GCp:
GCp Zone 4 Pos. = 0.90 (Fig. 6-11A, GCp is reduced by 10% for roof angle <=10 deg. )
GCp Zone 5 Pos. = 0.90 (Fig. 6-11A, GCp is reduced by 10% for roof angle <=10 deg. )
GCp Zone 4 Neg. = -0.99 (Fig. 6-11A, GCp is reduced by 10% for roof angle <=10 deg. )
GCp Zone 5 Neg. = -1.26 (Fig. 6-11A, GCp is reduced by 10% for roof angle <=10 deg. )
Positive & Negative Internal Pressure Coefficients, GCpi (Figure 6-5):
+GCpi Coef. = 0.18 (positive internal pressure)
-GCpi Coef. = -0.18 (negative internal pressure)
If z <= 15 then: Kz = 2.01*(15/zg)^(2/a) , If z > 15 then: Kz = 2.01*(z/zg)^(2/a) (Table 6-3, Case 1a)
a= 9.50 (Table 6-2)
zg = 900 (Table 6-2)
Kh = 0.86 (Kh = Kz evaluated at z = h)
I= 1.15 (Table 6-1) (Importance factor)
Velocity Pressure: qz = 0.00256*Kz*Kzt*Kd*V^2*I (Sect. 6.5.10, Eq. 6-15)
qh = 13.78 psf qh = 0.00256*Kh*Kzt*Kd*V^2*I (qz evaluated at z = h)
22 03/28/2022 04:56:37
Wind Load Tabulation for Wall Components & Cladding
Columns Corner to z Area qh p = Net Design Load (plf)
Ridge (ft.) Sft (psf) Zone 4 (+) Zone 4 (-) Zone 5 (+) Zone 5 (-)
Corner 16.00 85.33 13.78 43 -47 43 -53
1 16.67 111.11 13.78 84 -92 84 -102
2 17.33 115.56 13.78 84 -92 84 -101
3 18.00 120.00 13.78 83 -92 83 -101
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
p = Net Design Pressures Co-efficients (psf) p = Net Design Pressures (psf)
Zone 4 (+) Zone 4 (-) Zone 5 (+) Zone 5 (-) Zone 4 (+) Zone 4 (-) Zone 5 (+) Zone 5 (-)
0.75 0.75 -0.84 -0.96 12.84 -14.08 12.84 -15.77
0.73 0.73 -0.82 -0.93 12.59 -13.83 12.59 -15.26
0.73 0.73 -0.82 -0.92 12.56 -13.80 12.56 -15.19
0.73 0.73 -0.82 -0.92 12.52 -13.76 12.52 -15.12
Notes: 1. (+) and (-) signs signify wind pressures acting toward & away from respective surfaces.
2. Width of Zone 5 (end zones), 'a' = 4.00 ft.
3. Per Code Section 6.1.4.2, the minimum wind load for C&C shall not be less than 10 psf.
4. References : a. ASCE 7-02, "Minimum Design Loads for Buildings and Other Structures".
b. "Guide to the Use of the Wind Load Provisions of ASCE 7-02"
by: Kishor C. Mehta and James M. Delahay (2004).
23 03/28/2022 04:56:37
Wall Zones for Buildings with h <= 60 ft.
24 03/28/2022 04:56:37
Version 1.2
h
e
25 03/28/2022 04:56:37
WIND LOADING ANALYSIS - Roof Components and Cladding
Per ASCE 7-05 Code for Bldgs. of Any Height with Gable Roof
q <= 45o or Monoslope Roof q <= 3o
Using Method 2: Analytical Procedure (Section 6.5)
Job Name: ABCON ware house Subject: II
Job Number: MT-Q-****** Originator: Samad Checker: Aslam
IV
Input Data: B
C
Wind Speed, V = 80 mph (Wind Map, Figure 6-1) D
Bldg. Classification = III (Table 1-1 Occupancy Category) Gable
Exposure Category = C (Sect. 6.5.6) B
Monoslope
Ridge Height, hr = 18.00 ft. (hr >= he) Y
Eave Height, he = 16.00 ft. (he <= hr) N
Building Width = 40.00 ft. (Normal to Building Ridge) Purlin
Building Length = 40.00 ft. (Parallel to Building Ridge) Joist
L
Roof Type = Gable (Gable or Monoslope) Decking
Topo. Factor, Kzt = 1.00 (Sect. 6.5.7 & Figure 6-4) Plan Fastener
Direct. Factor, Kd = 0.85 (Table 6-4)
Enclosed? (Y/N) Y (Sect. 6.2 & Figure 6-5)
Hurricane Region? N qo
Component Name = Purlin (Purlin, Joist, Decking, or Fastener) hr
h
Effective Area, Ae = 133.33 ft.^2 (Area Tributary to C&C) h
Overhangs? (Y/N) N (if used, overhangs on all sides) e
L
Resulting Parameters and Coefficients: Elevation
26 03/28/2022 04:56:37
27 03/28/2022 04:56:37
Wind Load Tabulation for Roof Components & Cladding
Component z Kh qh p = Net Design Pressures (psf)
(ft.) (psf) Zone 1,2,3 (+) Zone 1 (-) Zone 2 (-) Zone 3 (-)
Purlin 0 0.86 13.78 5.24 -14.88 -17.64 -17.64
15.00 0.86 13.78 5.24 -14.88 -17.64 -17.64
For z = hr: 18.00 0.86 13.78 5.24 -14.88 -17.64 -17.64
Notes: 1. (+) and (-) signs signify wind pressures acting toward & away from respective surfaces.
2. Width of Zone 2 (edge), 'a' = 4.00 ft.
3. Width of Zone 3 (corner), 'a' = 4.00 ft.
4. For monoslope roofs with q <= 3 degrees, use Fig. 6-5B for 'GCp' values with 'qh'.
5. For buildings with h > 60' and q > 10 degrees, use Fig. 6-5B for 'GCpi' values with 'qh'.
6. For all buildings with overhangs, use Fig. 6-5B for 'GCp' values per Sect. 6.5.11.4.2.
7. If a parapet >= 3' in height is provided around perimeter of roof with q <= 10 degrees,
Zone 3 shall be treated as Zone 2.
8. Per Code Section 6.1.4.2, the minimum wind load for C&C shall not be less than 10 psf.
9. References : a. ASCE 7-02, "Minimum Design Loads for Buildings and Other Structures".
b. "Guide to the Use of the Wind Load Provisions of ASCE 7-02"
by: Kishor C. Mehta and James M. Delahay (2004).
28 03/28/2022 04:56:38
Roof Components and Cladding:
q <= 7 deg. 7 deg. < q <= 27 deg. 27 deg. < q <= 45 deg.
29 03/28/2022 04:56:38
CALCULATIONS:
30 03/28/2022 04:56:38
Width 'a' for Zone 2 for h <= 60': Width 'a' for Zone 2 for h > 60':
Lesser of L or B: 40.00 Lesser of L or B: N.A.
31 03/28/2022 04:56:38
0.1*(L or B): 4.00 0.1*(L or B): N.A.
Compare to 0.4*h: 4.00 Compare to 3': N.A.
Compare to .04*(L, B): 4.00 Use 'a' = N.A.
Compare to 3': 4.00
Use 'a' = 4.00
32 03/28/2022 04:56:38
Table 1.3.4.5(a)Main Framing Coefficients [(GCpf) – (GCpi)] for Transv
Roof Angle θ End Zone Coefficients Interior Zone Coefficients
Building Positive Pressure Co-Efficients
Type
1E 2E 3E 4E 1.00 2.00
0° ≤ θ ≤ 5° 0.43 -1.25 -0.71 -0.61 0.22 -0.87
0.43 -1.25 -0.71 -0.61 0.22 -0.87
Enclosed 2:12 0.49 -1.25 -0.76 -0.67 0.26 -0.87
Building 3:12 0.54 -1.25 -0.81 -0.74 0.30 -0.87
(ASCE 7) θ = 20° 0.62 -1.25 -0.87 -0.82 0.35 -0.87
30° ≤ θ ≤ 45° 0.51 0.09 -0.71 -0.66 0.38 0.03
θ = 90° 0.51 0.51 -0.66 -0.66 0.38 0.38
0° ≤ θ ≤ 5° 0.06 -1.62 -1.08 -0.98 -0.15 -1.24
0.06 -1.62 -1.08 -0.98 -0.15 -1.24
Partially 2:12 0.12 -1.62 -1.13 -1.04 -0.11 -1.24
Enclosed 3:12 0.17 -1.62 -1.20 -1.11 0.07 -1.24
(ASCE 7) θ = 20° 0.25 -1.62 -1.24 -1.19 -0.02 -1.24
30° ≤ θ ≤ 45° 0.14 -0.28 -1.08 -1.03 0.01 -0.34
θ = 90° 0.14 0.14 -1.03 -1.03 0.01 0.01
0° ≤ θ ≤ 10° 0.75 -0.50 -0.50 -0.75 0.75 -0.50
Open 0.75 -0.50 -0.50 -0.75 0.75 -0.50
(MBMA) 10° ≤ θ ≤ 25° 0.75 -0.50 -0.50 -0.75 0.75 -0.50
25° ≤ θ ≤ 45° 0.75 -0.50 -0.50 -0.75 0.75 -0.50
Notes:
1. Load Case refers to negative internal pressure (-i) and positive internal pressure (+i).
See Figure 6-5, ASCE 7-05 for the values used for GCpi.For the MBMA
recommendation for open buildings, load cases are provided for balanced and
unbalanced uplift cases.
4.00 5&6
-0.11 -0.27
-0.11 -0.27
-0.15 -0.27
-0.19 -0.27
-0.25 -0.27
-0.19 -0.27
-0.19 -0.27
0.26 0.10
0.26 0.10
0.22 0.10
0.18 0.10
0.12 0.10
0.18 0.10
0.18 0.10
-0.75 -0.75
-0.75 -0.75
-0.75 -0.75
-0.75 -0.75
Top in Compression Bottom in Compression
Thickness Weight Area Ix Zx-Top Zx-Bott. Ma Ix Zx-Top
mm kg/m2 cm 2 cm 4 cm 3 cm 3 kN.m cm 4 cm 3
0.5 4.99 6.36 4.05 2.15 4.97 0.44 3.44 2.22
0.6 5.99 7.63 5.13 2.96 6.3 0.61 4.5 2.83
0.7 6.99 8.9 6.15 3.64 7.61 0.75 5.61 3.44
Allowable loads in kN/m2
Panel Number of
Thickness Spans Load Case Span in meters
1 1.25 1.5 1.75 2 2.25
0.5 1 D+L 3.45 1.77 1.02 0.64 0.43 0.3
WP 4.69 2.65 1.54 0.97 0.65 0.46
WS 4.4 2.25 1.3 0.82 0.55 0.39
2 D+L 3.68 2.36 1.64 1.2 0.92 0.73
WP 4.91 3.14 2.18 1.6 1.23 0.97
WS 4.69 3 2.09 1.53 1.17 0.93
3 D+L 4.6 2.94 1.93 1.22 0.82 0.57
WP 6.13 3.92 2.73 1.82 1.22 0.86
WS 5.87 3.75 2.46 1.55 1.04 0.73
0.6 1 D+L 4.38 2.24 1.3 0.82 0.55 0.38
WP 6.51 3.36 1.95 1.23 0.82 0.58
WS 5.76 2.95 1.71 1.07 0.72 0.51
2 D+L 4.64 2.97 2.06 1.52 1.16 0.92
WP 6.19 3.96 2.75 2.02 1.55 1.22
WS 6.51 4.17 2.89 2.13 1.63 1.22
3 D+L 5.8 3.71 2.45 1.54 1.03 0.73
WP 7.73 4.95 3.44 2.31 1.55 1.09
WS 8.13 5.2 3.22 2.03 1.36 0.95
0.7 1 D+L 5.25 2.69 1.55 0.98 0.66 0.46
WP 7.87 4.03 2.33 1.47 0.98 0.69
WS 7.18 3.68 2.13 1.34 0.9 0.63
2 D+L 5.68 3.64 2.52 1.85 1.42 1.11
WP 7.58 4.85 3.37 2.47 1.89 1.5
WS 8 5.12 3.56 2.61 2 1.51
3 D+L 7.1 4.54 2.93 1.85 1.24 0.87
WP 9.46 6.06 4.21 2.77 1.86 1.3
WS 10 6.4 4.01 2.53 1.69 1.19
Bottom in Compression Web Shear & Cripp.
Zx-Bott. Ma Va Pa
cm 3 kN.m kN kN
3.14 0.46 11.89 5.97
4.31 0.58 18.58 9.44
5.55 0.71 25.45 13.4
meters
2.5 2.75 3 3.5 0
0.22 0.17 0.13 0.08
0.33 0.25 0.19 0.12
0.28 0.21 0.16 0.1
0.53 0.4 0.31 0.19
0.79 0.6 0.46 0.29
0.68 0.51 0.39 0.25
0.42 0.31 0.24 0.15
0.63 0.47 0.36 0.23
0.53 0.4 0.31 0.19
0.28 0.21 0.16 0.1
0.42 0.32 0.24 0.15
0.37 0.28 0.21 0.13
0.68 0.51 0.39 0.25
0.99 0.76 0.59 0.37
0.89 0.67 0.51 0.32
0.53 0.4 0.31 0.19
0.79 0.6 0.46 0.29
0.7 0.52 0.4 0.25
0.34 0.25 0.19 0.12
0.5 0.38 0.29 0.18
0.46 0.35 0.27 0.17
0.81 0.61 0.47 0.3
1.21 0.91 0.7 0.44
1.1 0.83 0.64 0.4
0.63 0.48 0.37 0.23
0.95 0.71 0.55 0.35
0.87 0.65 0.5 0.32
Design Sheet
X-Bracing Calculations
Job Name: ABCON ware house Subject:
Job Number: MT-Q-****** Originator: Samad Checker: Aslam
Input Data
Forces
Columns Nos. Tributory Forces in Nos. of
Tributory Acting on Cumulative Dia of Rope
from Eave to heights in Ropes at Ropes used
Areas "A" Joints of Forces "Pc" Used SR.<=1
Ridge End Wall "h" Roof "F" "n"
Cables "P"
Formulas:
h = Mean Height at two adjacent Columns =
A = Tributary Area of a Column = hxs/2
P = Forces on Cable Joints at Rafter Locations = A x Pr /( 2 x Bb)
Pc = Force Addition for two adjacent columns = P1 + P2
F = Forces acting in X-Area of Cable F = Pc x Lc / b
S.R. = Stress Ratio = SQRT (4 x d/1000/Fy x PI) x 25.4 / (n x d)
Pr =Wind Pressure = qh x Gcp (End Wall Zone 6)
38 03/28/2022 04:56:38
General Schematic Layout & Force Distribution of Bracing
Minimum Required
Total Bays Braced Bays
2 1
5 2
7 3
9 4
11 5
39 03/28/2022 04:56:38
Design Sheet
Hanger Door Support Calculations
Job Name: ABCON ware house Subject:
Job Number: MT-Q-****** Originator: Samad Checker: Aslam
Input Data
Length of Opening = 100.0 ft
Height of Opening = 20.0 ft
qh = 13.8 Psf
GCp = 1.0
No. of Supports = 10.0 Nos.
Depth of Door Pocket 'H' = 10.0 ft
Yield Strength 'Fy' = 50.0 Ksi
Force Diagram
40 03/28/2022 04:56:38
Design Sheet
Wind Column Load Calculation
& Bracing Calculations
Job Name: ABCON ware house Location: At Door Side
Job Number: MT-Q-****** Originator: Samad Checker: Aslam
Input Data
Forces
Columns Nos. Acting on Forces in
Tributory Tributory Cumulative
from Eave to Joints of Bracing
heights Areas Forces
Ridge Bracing Members
Membs
41 03/28/2022 04:56:38
General Schematic Layout & Force Distribution of Bracing
42 03/28/2022 04:56:38
RunWay Beam Design
As Per AISC Design Guide No. 7
T KN
3 17 4.8 3615 1000 30
Allowable Allowable
Lift Bridge Bridge Trolley+Hoist Wheel Bay End Wheel
Steel Grade Deflection Deflection %Age Load Addition
Capacity Span Weight Weight Spacing Width Clearence load(Max) (Vt) (Hz)
Kips ft Kips Kips ft ft Ksi ft Kips L / ? (in) L / ? (in) Vertical Lateral Longitudnal
Gutters Data:
Description Breadth (B) Depth (d) M=d/B
1 Eave Gutter 168.0 154.0 0.9
2 Common VG 400.0 190.0 0.5
3 High/Low VG 370.0 190.0 0.5
107.405617313786 KG/M2
Spacing with Sag Rods 6.2 m 107.8742
BMx 548.571395428794 KG.M 1.057891 5.43 5.38
*GIRT DESIGN
girt spacing 1.602347 M
wind pressure = 82.00 KN/M2 16.79614 PSF
cm2 In2
A = 6.452 cm2 1
Ixx= 1123.825 cm4 27
Zxx= 65.548 cm3 4
Zyy= 16.387 cm3 1
Iy 32.774 cm4 2
(3/384)X(W*L3)/EI
Loads
Dead Live Wind Down WindUplift D+L D+W
psf psf psf psf psf psf
Inner Bay 0 20 5.24 -14.88 20.00 5.24
Edge 0 20 5.24 -17.64 20.00 5.24
Corner 0 20 5.24 -17.64 20.00 5.24
Kn-M
Kn-M
5.07
6.07
7.42
8.56
9.81
11.72
9.96
12.97
lbs-ft
3,739.60
4,477.20
5,472.95
6,313.80
7,235.80
8,644.60
7,346.44
9,566.59
Spacing
D+(-Wu)
psf ft ft ft
14.88 7.20 27.51 9.68
17.64 7.20 27.51 8.17
17.64 7.20 27.51 8.17
Design Sheet
Purlin Design Sheet
Job Name: ABCON ware house Location: At Eave
Job Number: MT-Q-****** Originator: Samad Checker:
Input Data
Bay Spacing "B" = 20.00 ft
Slope = 5.71 Degrees
Material Used "Fy" = 50 Ksi
Sag Rods = 0.00 Nos.
Load Data
Basic Loads
Areas D RL Wd Wu
Psf
Inner Zone 0.00 20.00 5.24 -14.88
Edge Zone 0.00 20.00 5.24 -17.64
Corner Zone 0.00 20.00 5.24 -17.64
Load Combinations
Output
Allowable Stress = 33 Ksi
Allowable Deflection = 1.333333 in
Tributary Areaa = 129.0974 Sft
*GIRT DESIGN
girt spacing 0 M
wind pressure = 82.00 KN/M2 16.796142 PSF
cm2 In2
A = 6.452 cm2 1
Ixx= 1123.825 cm4 27
Zxx= 65.548 cm3 4
Zyy= 16.387 cm3 1
Iy 32.774 cm4 2
(3/384)X(W*L3)/EI
Loads
Dead Live Wind Down WindUplift D+L D+W
psf psf psf psf psf psf
Inner Bay 0 20 5.24 -14.88 20.00 5.24
9.96
12.97
lbs-ft
3,739.60
4,477.20
5,472.95
6,313.80
7,235.80
8,644.60
7,346.44
9,566.59
Spacing
D+(-Wu)
psf ft ft ft
14.88 7.20 27.51 9.68
2,195.35
PROJECT NAME :- 0
* SHEETING DESIGN
= 214.1789317 KGM
kn/m2
Thickness mm Weight kg/m2 Area cm2 Ix cm4 Zx-Top cm3 Zx-Bott. cm3 Ma kN.m
0.50 4.78 6.09 5.76 1.93 7.38 0.40
0.60 5.74 7.31 8.07 2.67 9.46 0.55
0.70 6.70 8.54 10.16 3.62 11.35 0.75
Span in Meters
2 2.25 2.5 2.75 3 3.5
0.63 0.44 0.32 0.24 0.19 0.12
0.95 0.67 0.49 0.37 0.28 0.18
0.91 0.64 0.47 0.35 0.27 0.17
1.02 0.81 0.65 0.54 0.45 0.28
1.36 1.07 0.87 0.72 0.6 0.43
1.06 0.84 0.68 0.56 0.47 0.35
1.2 0.84 0.61 0.46 0.35 0.22
1.7 1.26 0.92 0.69 0.53 0.33
1.33 1.05 0.85 0.66 0.51 0.32
0.89 0.62 0.45 0.34 0.26 0.17
1.33 0.94 0.68 0.51 0.39 0.25
1.21 0.85 0.62 0.47 0.36 0.23
1.3 1.03 0.83 0.69 0.58 0.4
1.73 1.37 1.11 0.91 0.77 0.56
1.46 1.16 0.94 0.77 0.65 0.48
1.63 1.18 0.86 0.64 0.5 0.31
2.17 1.71 1.29 0.97 0.74 0.47
1.83 1.45 1.17 0.88 0.68 0.43
1.12 0.78 0.57 0.43 0.33 0.21
1.68 1.18 0.86 0.64 0.5 0.31
1.52 1.07 0.78 0.58 0.45 0.28
1.58 1.25 1.01 0.84 0.7 0.5
2.1 1.66 1.34 1.11 0.93 0.69
2 1.58 1.28 1.06 0.89 0.65
1.98 1.48 1.08 0.81 0.62 0.39
2.63 2.08 1.62 1.22 0.94 0.59
2.5 1.97 1.47 1.1 0.85 0.53
2 1.0 Fy
F 0.60 F y , for F b F y / 3
3 2 2 y
F b 6 B F s F w = 16.68 ksi
B F s F w , for F b F y / 3
2 2
where Af = 0.78 in2
g = MIN[(dL - d0) / d0 , 0.268 L/d0, 6.0] = 0.00
ATo = tf bf + d0 tw / 6 = 1.01 in 2
Cv = 1.35
5.34 190 k v , for
4.0 , for a / h1.0
h /t C v 0.8
/ h 2
a = 5.37 w Fy
kv
5.34 4.0 , for a / h 1.0
a / h 2
Section Modulus 8.47 8.47 8.47 8.47 8.47 8.47 8.47 8.47 8.47 8.47 8.47 8.47 8.47
M Capacity 11.78 11.78 11.78 11.78 11.78 11.78 11.78 11.78 11.78 11.78 11.78 11.78 11.78
Shear Capacity 20.09 20.09 20.09 20.09 20.09 20.09 20.09 20.09 20.09 20.09 20.09 20.09 20.09
CHECK EACH SECTION CAPACITIES
Section HEEL 1/24 S 1/12 S 1/8 S 1/6 S 5/24 S 1/4 S 7/24 S 1/3 S 3/8 S 5/12 S 11/24 S MID
Distance 0 0.83 1.67 2.50 3.33 4.17 5.00 5.83 6.67 7.50 8.33 9.17 10.00
d (in) 9 9 9 9 9 9 9 9 9 9 9 9 9
I (in4) 38 38 38 38 38 38 38 38 38 38 38 38 38
Wt (plf) 9.9 9.9 9.9 9.9 9.9 9.9 9.9 9.9 9.9 9.9 9.9 9.9 9.9
V (kips) 4.50 4.12 3.75 3.37 3.00 2.62 2.25 1.87 1.50 1.12 0.75 0.37 0.00
M (ft-k) 0 4 7 10 12 15 17 19 20 21 22 22 22
fv (ksi) 3.22 2.96 2.69 2.42 2.15 1.88 1.61 1.34 1.07 0.81 0.54 0.27 0.00
fb (ksi) 0.00 5.09 9.74 13.94 17.70 21.02 23.90 26.33 28.32 29.87 30.98 31.64 31.86
0.00 1.51 2.88 4.12 5.24 6.22 7.07 7.79 8.38 8.84 9.16 9.36 9.43
0.90 0.82 0.75 0.67 0.60 0.52 0.45 0.37 0.30 0.22 0.15 0.07 0.00
BENDING STRESS
-fb (ksi)
0.00
-5.00
-10.00 0.83 19.17
-15.00 1.67 18.33
2.50 17.50
3.33 4.17 16.67
-20.00 5.00 5.83 15.0015.83
6.67 7.50 8.33 9.17 13.3314.17
-25.000.00 10.0010.8311.6712.50 20.00
-30.00
-35.00
Length
SHEAR STRESS
-fv (ksi)
0.00
-2.00
-4.00
-6.00
-8.000.00 0.83 1.67 2.50 3.33 4.17 5.00 5.83 6.67 7.50 8.33 9.17 10.8311.6712.5013.3314.1715.0015.83
16.6717.5018.3319.1720.00
-10.00
-12.00
-14.00
-16.00 10.00
Length
Technical Reference:
1. AISC: "Manual of Steel construction 9th", American Institute of Steel Construction, 1990.
Manual Input Auto From I/O Sheet
Joint No. x (ft.) y (ft.) Joint No. x (ft.)
1 1 0.0000
2 2 0.0000
3 3 20.0000
4 4 40.0000
5 5 40.0000
6 40.0000
1 2 3 4
JOB DETAILS
#VALUE! STAAD PLANE
#VALUE! START JOB INFORMATION
#VALUE! ENGINEER DATE 15-3-2011
#VALUE! ENGINEER NAME Samad
#VALUE! JOB NAME WARE HOUSE
#VALUE! JOB CLIENT Wajda
#VALUE! JOB NO. MT/Q-
#VALUE! JOB REV 0
#VALUE! JOB PART INNER FRAME
#VALUE! JOB COMMENT B= 20.00 FT
#VALUE! CHECKER NAME SAMAD
#VALUE! APPROVED NAME Aslam
#VALUE! CHECKER DATE 15-3-2011
#VALUE! APPROVED DATE 15-3-2011
#VALUE! END JOB INFORMATION
#VALUE! INPUT WIDTH 79
#VALUE! UNIT FEET KIP
#VALUE!
#VALUE! *********** JOINTS**************
#VALUE! JOINT COORDINATES
#VALUE! 1 0.00 0.00
#VALUE! 2 0.00 16.00
#VALUE! 3 20.00 18.00
#VALUE! 4 40.00 16.00
#VALUE! 5 40.00 0.00
#VALUE!
#VALUE!
#VALUE!
#VALUE!
#VALUE!
#VALUE!
#VALUE! ***********MEMBERS**********
#VALUE! MEMBER INCIDENCES
#VALUE! 1 1 2
#VALUE! 2 2 3
#VALUE! 3 4 3
#VALUE! 4 5 4
#VALUE!
#VALUE!
#VALUE!
#VALUE!
#VALUE!
#VALUE!
#VALUE!
#VALUE! ***********SECTIONS***********
#VALUE! START USER TABLE
#VALUE! TABLE 1
#VALUE! UNIT MMS KIP
#VALUE! ISECTION
#VALUE! C1
#VALUE! 200 4 900 200
#VALUE! R1
#VALUE! 900 4 300 200
#VALUE!
#VALUE!
#VALUE!
#VALUE!
#VALUE!
#VALUE!
#VALUE!
#VALUE!
#VALUE!
#VALUE!
#VALUE! END
#VALUE! UNIT FEET KIP
#VALUE! ***********MATERIAL*********
#VALUE! DEFINE MATERIAL START
#VALUE! ISOTROPIC STEEL
#VALUE! E 4.18E+06
#VALUE! POISSON 0.3
#VALUE! DENSITY 0.489024
#VALUE! ALPHA 6.50E-06
#VALUE! DAMP 0.03
#VALUE! END DEFINE MATERIAL
#VALUE!
#VALUE!
#VALUE!
#VALUE!
#VALUE!
#VALUE!
#VALUE!
#VALUE!
#VALUE!
#VALUE!
#VALUE!
#VALUE!
#VALUE!
#VALUE! ********MEMBERS*********
#VALUE! MEMBER PROPERTY AMERICAN
#VALUE! 1 4 UPTABLE
#VALUE! 2 3 UPTABLE
#VALUE!
#VALUE! CONSTANTS
#VALUE! MATERIAL STEEL ALL
#VALUE! **********SUPPORTS**********
#VALUE! SUPPORTS
#VALUE! 1 5 FIXED
#VALUE!
#VALUE!
#VALUE! **************LOADS***********
#VALUE! UNIT FEET POUND
#VALUE! LOAD 1 LOADTYP Dead
#VALUE! SELFWEIGY -1
#VALUE! MEMBER LOAD
#VALUE!
#VALUE! 2 3 UNI GY
#VALUE!
#VALUE!
#VALUE!
#VALUE!
#VALUE! LOAD 2 LOADTYP ROOF LIV
#VALUE! MEMBER LOAD
#VALUE! 2 3 UNI
#VALUE!
#VALUE!
#VALUE!
#VALUE!
#VALUE! LOAD 3 LOADTYP WIND
#VALUE! MEMBER LOAD
#VALUE! 1 uni gx
#VALUE! 2 uni gy
#VALUE! 3 uni gy
#VALUE! 4 uni gx
#VALUE!
#VALUE!
#VALUE! LOAD 4 LOADTYP WIND
#VALUE! MEMBER LOAD
#VALUE! 1 uni gx
#VALUE! 2 uni gy
#VALUE! 3 uni gy
#VALUE! 4 uni gx
#VALUE!
#VALUE!
#VALUE! LOAD 5 LOADTYP WIND
#VALUE! MEMBER LOAD
#VALUE! 4 uni gx
#VALUE! 3 uni gy
#VALUE! 2 uni gy
#VALUE! 1 uni gx
#VALUE!
#VALUE!
#VALUE! LOAD 6 LOADTYP WIND
#VALUE! MEMBER LOAD
#VALUE! 4 uni gx
#VALUE! 3 uni gy
#VALUE! 2 uni gy
#VALUE! 1 uni gx
#VALUE!
#VALUE! ************LOADS COMBINATIONS***********
#VALUE!
#VALUE!
#VALUE!
#VALUE!
#VALUE!
#VALUE!
#VALUE!
#VALUE!
#VALUE!
#VALUE!
#VALUE!
#VALUE!
#VALUE!
#VALUE!
#VALUE!
#VALUE!
#VALUE!
#VALUE!
#VALUE!
#VALUE!
#VALUE! PERFORM ANALYSIS
#VALUE! LOAD LIST ALL
#VALUE! UNIT FEET KIP
#VALUE! *********DESIGN***********
#VALUE! PARAMETER 1
#VALUE! CODE AISC
#VALUE! BEAM 1 ALL
#VALUE! FYLD 5182 ALL
#VALUE! LY 4 ALL
#VALUE! STIFF 12 ALL
#VALUE! TAPER 1 ALL
#VALUE! UNT 4 ALL
#VALUE! UNB 8 ALL
#VALUE! CHECK CODE ALL
#VALUE! UNIT FEET KGS
#VALUE! STEEL TAKE OFF LIST 1 TO 4
#VALUE! UNIT FEET KIP
#VALUE! STEEL TAKE OFF LIST 1 TO 4
#VALUE!
#VALUE!
#VALUE!
#VALUE!
#VALUE!
#VALUE!
#VALUE!
#VALUE!
#VALUE!
#VALUE!
#VALUE!
#VALUE! FINISH
20.0
Y-axis (ft.)
y (ft.) 18.0
0.0000 16.0 Autocad Script
16.0000 14.0 L
18.0000 12.0 #VALUE! 0.0 0.0
10.0
16.0000 #VALUE! 0.0 16.0
8.0
0.0000 #VALUE! 20.0 18.0
6.0
4.0
#VALUE! 40.0 16.0
2.0
#VALUE! 40.0 0.0
0.0 X-axis (ft.) #VALUE! 40.0 0.0
0.0 5.0 10.0 15.0 20.0 25.0 30.0 35.0 40.0 45.0
L
5 6 7 8 9 10 1 #VALUE! 0.7 0.0
2 #VALUE! 2.9527559 13.04724
3 #VALUE! 20.0 17.01575
4 #VALUE! 37.047244 13.04724
5 #VALUE! 39.343832 0.0
#VALUE!
#VALUE!
#VALUE!
#VALUE!
#VALUE!
#VALUE!
#VALUE!
#VALUE!
0
0
0
0
0
5 200 5 0 0 0
5 200 5 0 0 0
1 C1
1 R1
TITLE D
LIST ALL
-60.00
TITLE RL
GY -240.00
TITLE W+X+
62
240
153
131 0 0
TITLE W+X-
162 0 0
141
54
32 0 0
TITLE W+X-'
-62 0 0
240
153
-131 0 0
TITLE W-X-'
-162 0 0
141
54
-32 0 0
Sections
0.0 C1
0.0 200 4 900 200 5 200 5
0.0 R1
0.0 900 4 300 200 5 200 5
0.0
0.0
0.0
0.0
0.0
0.0
0.0
0.0