Professional Documents
Culture Documents
SPEAKER
Active 2-Way Sound
SRM450 Reinforcement Speaker System
The Mackie Designs SRM450 is a full range, portable,
active loudspeaker system providing high output, wide
dispersion, and low distortion performance in a compact,
composite molded enclosure. Two amplifiers independent-
SRM450
ly power a high precision 12-inch professional woofer and
1.75-inch diaphragm titanium compression driver with a
1-inch exit throat. A sophisticated electronic control sys-
tem provides phase correction, crossover, and five modes
of thermal and active system protection.
The SRM450 is fitted with a specially designed horn
assembly that combines both an exponential and conical
geometry. With the addition of a multi-cell horn throat
aperture, the complete assembly provides unparalleled
dispersion characteristics. The result is super smooth, low-
Features
Bi-amplification with 300 watts rms low-frequency
distortion linear audio performance across the entire spec- and 100 watts rms high-frequency power
ified coverage angle of 90 degrees.
127 dB peak SPL
A servo feedback circuit has been added to the low-
frequency amplifier in order to provide extended bass Wide dispersion, studio-quality high-frequency
response and woofer control. This design provides simul- horn with multi-cell aperture throat
taneous positive and negative signal feedback information Large format exponential/conical high-frequency
from the woofer’s magnetic circuit to the low-frequency horn mouth
amplifier. This loop locks the two devices together and State of the art RCF Precision 1.75-inch titanium
provides extreme control of the woofer mass. The result is compression driver
extended linear movement of the woofer cone resulting in Servo feedback controlled RCF Precision
very high SPL low-frequency output levels. 12-inch high-efficiency, light mass woofer
Careful attention has been given to the ergonomic fea- Single mic/line level control
tures of the system. The center of gravity, handle loca-
High-pass switch for floor monitoring applications
tions, handle design, position of fly-points, and ease of
use have been carefully thought out. There is also an inte- Contour switch provides ideal low to medium
grated pole mount on the bottom of the cabinet and a level music playback equalization
weather-resistant steel grille. The asymmetrical trapezoi- Timed turn-off AC switch
dal cabinet has been designed to provide an ideal floor Complete electronic and component protection
monitoring position. circuitry
The SMR450 features a number of unique control fea- Electronic equalization and phase alignment
tures including a single microphone and line-level control
Professional trapezoidal enclosure design
in addition to a high-pass filter for floor monitoring appli-
cations, an AC timed turn off function that is ideal for fixed Built-in pole mount cup on bottom
or remote installations, and a contour switch for low-level Tilts on its side for use as a stage monitor
or background-level sound reinforcement applications. Correctly weight-balanced with two comfort-
The SRM450 cabinet is constructed of high pressure able side handles for easy carrying and set up
injected polypropylene. The enclosure features ample
amounts of reinforcement ribbing and structural strength-
ening resulting in a strong, super-rigid design providing
ideal acoustical characteristics. Applications
Live and playback applications
Small to medium sized protable PA systems
1
Corporate events
O Fo F66 PA
P AG EGSE S
Houses of worship
SPEAKER
SRM450 Active Speaker System
SRM450 Specifications
System Acoustic Low Frequency Section
Frequency Response (–3 dB) 55 Hz-18 kHz Number of Drivers 1
Frequency Range (–10 dB) 45 Hz-20 kHz Woofer Diameter 12 in/300 mm
Directivity Factor; Q (DI) 9.95 (9.98), averaged Voice Coil Diameter 2.5 in/63 mm
2 kHz to 10 kHz Power Handling 450 watts rms (long term)1
Max SPL Long-term 124 dB Sensitivity 98 dB (1W@1m)
SRM450
Safety Features
*Rated power is continuous rms wattage into transducer’s rated impedance @ 1 kHz for
the HF amplifier and @ 100 Hz for the LF amplifier Protection Low Frequency Dynamic Bass
Protection, Independent LF and HF
High Frequency Section Compressors, Power Supply and
Amplifier Thermal Protection
Diaphragm Size 1.75 in/44.5 mm
Display LEDs Signal Present, Peak, Power ON, and
Horn Exit Diameter 1.0 in/24.5 mm Thermal (Cool Down Auto Reset)
Power Handling 100 watts rms (long term)1
Sensitivity 106 dB (1W@1m) Physical
Frequency Range 1000 Hz to 20 kHz Height 26.0 in/660 mm
Nominal Impedance 8 ohms Width Front 15.4 in/390 mm
Diaphragm Material Damped titanium Depth 14.8 in/376 mm
Magnet Type Ferrite Weight 51.0 lb/23.2 kg
200Hz 500Hz
250Hz 630Hz
180° 0° 180° 0°
–36 –12 315Hz –36 –12 800Hz
400Hz 1kHz
90° 90°
120° 60° 120° 60°
1.25kHz 3.15kHz
1.6kHz 4kHz
180° 0° 180° 0°
–36 –12 2kHz –36 –12 5kHz
2.5kHz 6.3kHz
10
150° 30°
0
0 deg
Attenuation (dB)
10 deg
8kHz –10 20 deg
10kHz 30 deg
180° 0° –20
40 deg
–36 –12 12.5kHz
16kHz –30
20 100 1000 10000 20000
Frequency (Hz)
0
0 deg
Attenuation (dB)
–10 deg
–10 –20 deg
–30 deg
3
–20
O Fo F66 PA
P AG EGSE S
–40 deg
–30
20 100 1000 10000 20000
Frequency (Hz)
SRM450 Active Speaker System
–12 –12
–36 –36
200Hz 500Hz
250Hz 630Hz
270° 90° 270° 90°
315Hz 800Hz
400Hz 1kHz
0° 0°
330° 30° 330° 30°
–12 –12
–36 –36
1.25kHz 3.15kHz
1.6kHz 4kHz
270° 90° 270° 90°
2kHz 5kHz
2.5kHz 6.3kHz
0°
330° 30°
–12
300° 60°
–36
8kHz
16kHz
10
240° 120°
0
0 deg
Attenuation (dB)
10 deg
210° 150° –10 20 deg
180° 30 deg
–20
40 deg
–30
20 100 1000 10000 20000
Frequency (Hz)
4 O Fo F66 PA
P AG EGSE S
SRM450 Active Speaker System
SRM450 Frequency Response On-Axis
110
90
80
70
20 100 1000 10000 20000
Frequency (Hz)
180 10 10
120 Vert BW
Horz BW
60
0 0 1
20 100 1000 10000 20000 20 100 1000 10000 20000
Frequency (Hz) Frequency (Hz)
NORMAL
(+4dBu)
SRM450 Dimensions
15.4 in/390 mm 14.8 in/376 mm
26.0 in/660 mm
14.8 in/376 mm
15.4 in/390 mm
5 O Fo F66 PAGES
PAGES
SPEAKER
SRM450 Active Speaker System
Architects’ and Engineers’ Specifications
The active two-way, full-range loudspeaker system Thermal protection shall be provided by a thermal
shall incorporate one 12-inch low-frequency (LF) trans- sensor mounted on the heatsink, which monitors the
ducer and a 1-inch exit/1.75-inch diaphragm compression heatsink temperature and triggers the thermal protection
driver high-frequency (HF) transducer. The LF driver shall circuit should the temperature exceed 158° F (70° C). The
be mounted in a vented polypropylene molded enclosure Thermal LED shall light and the input signal to the ampli-
SRM450
tuned for optimum low-frequency response. The HF trans- fiers shall be muted until the heatsink cools to a safe oper-
ducer shall be loaded on a multi-cell horn aperture and ating level, at which point the thermal protection circuit
mounted on a combination exponential and conical horn. auto-resets and normal operation resumes.
The system shall have a nominal coverage pattern of Overload protection for the LF driver shall be provided
90° (horizontal) x 40° (vertical). System frequency response by a dynamically variable high-pass filter, the corner fre-
shall vary no more than ±3 dB from 55 Hz to 18 kHz quency of which shall slide from 40 Hz to 120 Hz as the LF
measured on axis. The loudspeaker shall incorporate a amplifier output approaches clipping. Additional protec-
Class G low-frequency amplifier capable of delivering 300 tion shall be provided for both the LF and HF drivers by a
watts rms over a frequency range of 20 Hz-2000 Hz. The compressor circuit, which monitors the low-frequency and
system shall incorporate a Class AB 100 watt rms ampli- high-frequency amplifier outputs and reduces the gain as
fier specifically designed to power the HF driver over the the amplifiers approach clipping.
range of 1500 Hz-20 kHz. The amplifiers shall be mounted The system shall include an XLR input connector, an
on an aluminum heatsink, which shall be mounted on the XLR loop-through signal connector, a level control capable
rear of the speaker system, and shall be convection cooled. of providing up to 40 dB of gain to accomodate both
microphone and line-level signal levels, a sound contour
switch providing +3 dB of equalization at 100 Hz and 12 kHz,
a high-pass switch for filtering out frequencies below 75 Hz,
and a timed turn-off switch for self shut-down.
SRM450 Block Diagram The loudspeaker enclosure shall have an asymmetrical
trapezoidal shape and shall incorporate 10 integrated M10
THRESHOLD
fly points, two side handles, and a top relocation handle.
LOW CUT CONTOUR
J15
HI-PASS The enclosure shall be molded from polyproylene material.
2 HI-FREQ HI-FREQ
176uS
POWER SWEEPING
FILTER LO-FREQ
SWITCH WOOF
FUSE AMP
+ +
MID VDC HI VDC THRESHOLD
– – THRESHOLD LPF
MACKIE DESIGNS
SRM450
BLOCK DIAGRAM
(#060322SEDF)
6
ITALY +39.0522.354.111, fax +39.0522.926.208, italy@mackie.com
FRANCE +33.3.85.46.91.60, fax +33.3.85.46.91.61, france@mackie.com O FoF66 PA
P AG EGSE S
GERMANY +49.2572.96042.0, fax +49.2572.96042.10, germany@mackie.com