Professional Documents
Culture Documents
Tower Mods Web
Tower Mods Web
These guy brackets are designed for 5/8” EHS maximum guys at 80% guy
Torque Bar Shown radius. For use on ROHN Model 80 tower only, supported on brace clips.
For single braced standard sections, guy bracket must be used at the top
4 of the section.
1
Tower Brace (REF) For double braced standard sections, guy brackets may be used at any panel
point.
1 4 For single braced standard sections, guy bracket must be used at the top
of the section.
Tower Brace (REF)
For double braced standard sections, guy brackets may be used at any panel
point.
282 Phone (309) 566-3000 • Fax (309) 566-3079 • www.rohnnet.com • The Industry Standard
© 2011 ROHN PRODUCTS LLC
T O W E R M O D I F I C AT I O N M AT E R I A L - G U Y E D T O W E R S M
TORQUE ARM
C H A N N E L A S S E M B LY F O R 8 0 T O W E R S
Available Sizes:
• 10” Channel (C10x15.3)
• 12” Channel (C12x20.7)
• 15” Channel (C15x33.9)
Tower
Leg Clamp
Bolt Assembly
Bottom Plate
NOTE: For single braced sections, torque arm must bear on brace clips above flange plates. For double braced sections,
torque arm must bear on brace clips at any panel point.
Phone (309) 566-3000 • Fax (309) 566-3079 • www.rohnnet.com • The Industry Standard
283
© 2011 ROHN PRODUCTS LLC
M T O W E R M O D I F I C AT I O N M AT E R I A L - G U Y E D T O W E R S
284 Phone (309) 566-3000 • Fax (309) 566-3079 • www.rohnnet.com • The Industry Standard
©2011 ROHN PRODUCTS LLC
T O W E R M O D I F I C AT I O N M AT E R I A L - G U Y E D T O W E R S M
REINFORCEMENTS FOR 80 SERIES TOWERS
S TA N D A R D PA R T S AVA I L A B L E F O R T O W E R M O D I F I C AT I O N S
AND FIELD REINFORCEMENT
Similar reinforcements available for 90 series towers.
DetailDetail of bolt-on
of bolt-on horizontal
midspan brace.
horizontal bracket.
Phone (309) 566-3000 • Fax (309) 566-3079 • www.rohnnet.com • The Industry Standard
285
© 2011 ROHN PRODUCTS LLC
M TOWER MODIFICATION MATERIAL - SELF-SUPPORTING TOWERS
SELF-SUPPORTING REINFORCEMENTS
S TA N D A R D PA R T S AVA I L A B L E F O R T O W E R M O D I F I C AT I O N S
AND FIELD REINFORCEMENT
Horizontal Girt
(Typ)
Girt Support
Bracket
Tower Leg
(Ref ) Bolt
Assembly
Diagonal Tower
Braces
Added horizontal
girt to increase leg
capacity (TYP)
1/2” Leg
U-bolt Center Plate
Center Plate
Diagonal Tower
Braces (Ref ) Horizontal Girt (Typ)
1/2” Leg
U-Bolt VIEW A-A
286 Phone (309) 566-3000 • Fax (309) 566-3079 • www.rohnnet.com • The Industry Standard
© 2011 ROHN PRODUCTS LLC
TOWER MODIFICATION MATERIAL - SELF-SUPPORTING TOWERS M
SSMW SELF-SUPPORTING REINFORCEMENTS
S TA N D A R D PA R T S AVA I L A B L E F O R T O W E R M O D I F I C AT I O N S
AND FIELD REINFORCEMENT
Added redundants to
increase brace and leg
capacity (TYP)
U-bolt Connection
(Typical)
Phone (309) 566-3000 • Fax (309) 566-3079 • www.rohnnet.com • The Industry Standard
287
© 2011 ROHN PRODUCTS LLC
M T O W E R M O D I F I C AT I O N M AT E R I A L
ANCHOR RODS
Type L A B C D T Part No. Weight (lbs.)
GAR 84” 1” - 2” 5/8” - GAR30 9
GAC 84” 2” - 1” 5/8” 3/16” GAC303 13
GAC 84” 2” - 1” 5/8” 3/16” GAC305 14
GAC34 84” 2” 12” 1” 3/4” 3/8” GAC3455TOP 25
GAC56 120” 2-1/2” 12” 1-1/4” 1-1/4” 1/2“ GAC5655TOP 65
GAC57 168” 3” 12” 1-3/8” 1-7/16” 3/4” GAC5755TOP 125
GAC58 192” 4” 12” 1-3/4” 1-1/4” 1” GAC5855TOP 220
GAC59 240” 4” 18” 1-3/4” 1-7/16” 1” GAC5955TOP 310
3/4” dia.
bolt
included
(2) 3/16”
plates, one
on each
side
L L
L L
GAR30
Anchor
Rod
D D
D D
5-1/4" 5-1/4" B B
NOTE: GAC Anchors require use of eye and eye turnbuckles. All other anchors are for
use with eye and jaw turnbuckles. Refer to page 297.
288 Phone (309) 566-3000 • Fax (309) 566-3079 • www.rohnnet.com • The Industry Standard
© 2011 ROHN PRODUCTS LLC